30208-DF bearing: complete specifications & equivalents

The 30208-DF is a ISO 355 radial bearing sized 40 x 80 x 39.5 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 80 mm d = 40 B = 39.5 mm side section front view
Principal dimensions: bore d 40 mm, outer diameter D 80 mm, width B 39.5 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 40 mm
Outer diameter D 80 mm
Width B 39.5 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 130 kN
Basic static load rating C0 137 kN
Fatigue load limit Pu 15.3 kN
Reference speed (thermal) 5600 rpm
Limiting speed (mechanical) 8500 rpm
Operating temperature -40 to +120 °C
Mass 870 g
Manufacturer designation SKF 30208/DF
Standard ISO 355
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants
Last verified 2026-09-29

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants) · extracted 2026-09-29

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & matched-df-series range

Bore d1.575 in
Outer diameter D3.15 in
Width B1.555 in
ISO bore code08
Radial section height (D−d)/220 mm
Smallest bore in matched-df-series25 mm
Largest outer diameter in matched-df-series540 mm
Width range across matched-df-series34.5–280 mm
Bore position in matched-df-series (smallest first)4 of 35
Bore above smallest matched-df-series size15 mm

Mounting, setting & life for 30208-DF

Fits & mounting

  • Tapered bearings are separable: press the cup square into the housing and fit the cone on the shaft — usually an interference fit on both seats in wheel/hub positions.
  • Mount the cone by induction heating (max 120 °C); never strike the cage or rollers directly.
  • Shaft and housing shoulders must clear the ring chamfers so the cone and cup seat fully against their faces.

Setting — the step deep-groove bearings never need

  • After seating, set the assembly to a defined end play or preload with the locknut/shim arrangement; locknut torque seats the parts — it is not the final adjustment.
  • General free-running positions: back the nut off while measuring with a dial indicator to a small end play (commonly around 0.05–0.15 mm for medium metric hubs — follow the OEM value).
  • Pinions and stiff arrangements run a controlled preload; too much preload is the classic cause of early spalling and heat.
  • Sealed factory-set units exist for specific designations — the open 30208-DF assumes the application sets and lubricates it.

Lubrication

Open TRBs are lubricated by the application. Fill the bearing with grease (typically around one third to one half of the free cavity — overpacking a TRB causes churning heat) and provide a relubrication path; intervals depend on contamination and temperature, not on catalogue rating alone.

Why the equivalent load matters more here

TRBs carry combined radial and axial loads, so the dynamic equivalent load P is computed with the bearing's e, X and Y factors for the actual thrust ratio — using the radial load alone over-estimates life badly.

Worked L10 life example (illustrative duty)

For roller bearings the life exponent is p = 10/3: L10h = (C/P)10/3 · 106 / (60·n). Taking an example equivalent load P = 26 kN (20% of C) at n = 1,500 r/min — substitute the real P from the X/Y calculation:

C = 130.0 kN → L10h ≈ 2,375 hours

Choosing a series at the same 40 mm bore

SeriesOpen executionOD × width TC (kN)C0 (kN)Limiting speed (r/min)
320xx3200868 × 1963.071.012,800
302xx3020880 × 19.7575.868.08,500
322xx3220880 × 24.7594.094.011,200
332xx3320880 × 32128.0132.08,500
303xx30308C90 × 25.2592.087.04,200
323xx32308C90 × 35.25122.0140.04,200
313xx3130890 × 25.2591.181.57,500

Different series at the same bore are not drop-in swaps — OD, width and contact angle all change — and a cone number alone never identifies a complete set. Verify matches per the cross-reference levels guide; envelope variants are on the 40×80×39.5 envelope page.

Cross references & equivalents

Equivalent modelBrandMatch levelNote
30208 ISO 15 full
Dimensions and internal design equivalent — standard interchange.
ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier.
30208-NTN NTN verify
Commonly quoted cross reference; confirm against the target catalog before ordering.
Model-number interchange per ISO 15; confirm dimensions, sealing and ratings in the supplier catalogue.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 30208-DF model number is decoded

Thermal behaviour of the pair: heat generated in the 40 mm bore cones flows along the shaft and changes the setting; the /DF clearance class is chosen for the catalogue speed range 5,600–8,500 r/min, so re-select the clearance class if the application runs hotter. Lubrication for the pair should be sized against the combined 39.5 mm width and 870 g mass: two roller sets sweep twice the contact area of a single bearing of the same bore.Ordering number SKF 30208/DF in SKF catalogue PUB BU/P1 17000 denotes two single-row tapered roller bearings supplied as a matched face-to-face (X) matched pair set for a 40 mm shaft — one order number, one factory setting.On the SKF nameplate, 30208-DF reads as base 30208 in a /DF matched execution — the suffix is part of the order number because a matched set is ground for a specific axial clearance and cannot be assembled from loose single bearings. In the face-to-face (X) arrangement the load lines of the two bearings converge toward the shaft axis: the set tolerates shaft deflection and thermal growth better than a back-to-back pair, but is less stiff against overturning moments. The 39.5 mm overall width of 30208-DF is the axial space the pair occupies. With a pair mass of 870 g across the 40×80×39.5 mm envelope, the set replaces what would otherwise be two separate bearings plus spacer grinding work — the factory setting is the engineering value being purchased. Cross-section geometry: the 20.0 mm half-section ((80−40)/2) places the roller pitch diameter near 60 mm, and the 39.5 mm axial width sets the abutment depth — geometry that fixes the contact angle behaviour of 30208-DF.

Typical equipment & failure modes

Common applications

  • industrial gearbox shafts and reducers
  • differential and pinion drives
  • pump and compressor shafts
  • machine-tool spindles

Known failure patterns

  • axial overload spalling at the roller-rib contact beyond the single-row thrust rating
  • preload loss as the mounted pair relaxes, letting rollers skid and smear the raceways
  • pressed-steel cage wear or fracture after prolonged running above the limiting speed
  • edge loading from shaft deflection or housing misalignment
  • fretting corrosion on a loose rotating shaft seat

Selection pitfalls — read before you substitute

  • O and X arrangements are not interchangeable by turning the set around: 30208-DF in face-to-face (X) matched pair arrangement has its load-line geometry fixed — specify the arrangement from the shaft thermal and stiffness analysis.
  • Setting is built into 30208-DF; the classic field error is re-adjusting a matched pair as if it were two loose single bearings, which destroys the /DF clearance class.
  • Replace 30208-DF as a complete set: pairing a new bearing with a worn partner leaves the clearance undefined even when the designation matches.
  • The 130/137 kN ratings are SKF catalogue 17000 values for this execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification.
  • Quote the full SKF 30208/DF designation when purchasing — base-number-only orders are ambiguous across executions and variants.

Frequently asked questions

What are the dimensions and catalogue data of 30208-DF?

The SKF 30208/DF is a matched pair of single-row tapered roller bearings in face-to-face (X) matched pair arrangement with 40 mm bore, 80 mm outer diameter and 39.5 mm overall width (1.575 × 3.15 × 1.555 in). From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 130 kN, C0 137 kN, fatigue load limit Pu 15.3 kN, reference speed 5,600 r/min, limiting speed 8,500 r/min, mass about 0.87 kg.

What does the /DF suffix on 30208-DF mean?

The base 30208 is the ISO 355 single-row bearing; the /DF suffix marks the matched-set execution — the arrangement (face-to-face (X)), the ground spacer and the factory-set axial clearance class. A matched set cannot be assembled from loose single bearings; quote the full designation when ordering.

Are the C and C0 ratings of 30208-DF for one bearing or the pair?

They are for the complete matched pair: C 130 kN dynamic and C0 137 kN static already include load sharing between the two bearings. Do not halve them for single-bearing checks, and do not compare them directly with the single-row 30208 table values.

Can 30208-DF be adjusted like two loose tapered bearings?

No — the axial clearance is set at the factory by selective spacer grinding. Mounting work is limited to clean seats, correct fits (k5 on a rotating 40 mm shaft) and axial clamping through the cones; re-setting in the field destroys the matched clearance class.

When should a face-to-face (X) matched set be chosen?

Choose the face-to-face (X) set where the shaft grows thermally or alignment is imperfect — the converging load lines tolerate deflection. It is the default choice for wheel hubs and general gearbox shafts at the 40 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants on 2026-09-29. Read our editorial & correction policy.