30206-DF bearing: complete specifications & equivalents
The 30206-DF is a ISO 355 radial bearing sized 30 x 62 x 34.5 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 30 mm |
| Outer diameter D | 62 mm |
| Width B | 34.5 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 85.7 kN |
| Basic static load rating C0 | 88 kN |
| Fatigue load limit Pu | 9.65 kN |
| Reference speed (thermal) | 7500 rpm |
| Limiting speed (mechanical) | 11000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 480 g |
| Manufacturer designation | SKF 30206/DF |
| Standard | ISO 355 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants |
| Last verified | 2026-09-29 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants) · extracted 2026-09-29
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & matched-df-series range
| Bore d | 1.181 in |
|---|---|
| Outer diameter D | 2.441 in |
| Width B | 1.358 in |
| ISO bore code | 06 |
| Radial section height (D−d)/2 | 16 mm |
| Smallest bore in matched-df-series | 25 mm |
| Largest outer diameter in matched-df-series | 540 mm |
| Width range across matched-df-series | 34.5–280 mm |
| Bore position in matched-df-series (smallest first) | 2 of 35 |
| Bore above smallest matched-df-series size | 5 mm |
Mounting, setting & life for 30206-DF
Fits & mounting
- Tapered bearings are separable: press the cup square into the housing and fit the cone on the shaft — usually an interference fit on both seats in wheel/hub positions.
- Mount the cone by induction heating (max 120 °C); never strike the cage or rollers directly.
- Shaft and housing shoulders must clear the ring chamfers so the cone and cup seat fully against their faces.
Setting — the step deep-groove bearings never need
- After seating, set the assembly to a defined end play or preload with the locknut/shim arrangement; locknut torque seats the parts — it is not the final adjustment.
- General free-running positions: back the nut off while measuring with a dial indicator to a small end play (commonly around 0.05–0.15 mm for medium metric hubs — follow the OEM value).
- Pinions and stiff arrangements run a controlled preload; too much preload is the classic cause of early spalling and heat.
- Sealed factory-set units exist for specific designations — the open 30206-DF assumes the application sets and lubricates it.
Lubrication
Open TRBs are lubricated by the application. Fill the bearing with grease (typically around one third to one half of the free cavity — overpacking a TRB causes churning heat) and provide a relubrication path; intervals depend on contamination and temperature, not on catalogue rating alone.
Why the equivalent load matters more here
TRBs carry combined radial and axial loads, so the dynamic equivalent load P is computed with the bearing's e, X and Y factors for the actual thrust ratio — using the radial load alone over-estimates life badly.
Worked L10 life example (illustrative duty)
For roller bearings the life exponent is p = 10/3: L10h = (C/P)10/3 · 106 / (60·n). Taking an example equivalent load P = 17.1 kN (20% of C) at n = 1,500 r/min — substitute the real P from the X/Y calculation:
C = 85.7 kN → L10h ≈ 2,375 hours
Choosing a series at the same 30 mm bore
| Series | Open execution | OD × width T | C (kN) | C0 (kN) | Limiting speed (r/min) |
|---|---|---|---|---|---|
| 320xx | 32006 | 55 × 17 | 46.0 | 47.0 | 16,100 |
| 302xx | 30206 | 62 × 17.25 | 50.0 | 44.0 | 11,000 |
| 322xx | 32206 | 62 × 21.25 | 63.0 | 62.0 | 14,600 |
| 332xx | 33206 | 62 × 25 | 79.7 | 76.5 | 11,000 |
| 303xx | 30306CA | 72 × 20.75 | 65.0 | 58.5 | 5,500 |
| 323xx | 32306C | 72 × 28.75 | 88.0 | 94.0 | 5,500 |
| 313xx | 31306 | 72 × 20.75 | 58.3 | 50.0 | 9,500 |
Different series at the same bore are not drop-in swaps — OD, width and contact angle all change — and a cone number alone never identifies a complete set. Verify matches per the cross-reference levels guide; envelope variants are on the 30×62×34.5 envelope page.
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 30206 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
| 30206-NTN | NTN | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | Model-number interchange per ISO 15; confirm dimensions, sealing and ratings in the supplier catalogue. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 30206-DF model number is decoded
SKF 30206/DF belongs to the SKF matched tapered-roller range — the 30 mm bore entry in face-to-face (X) matched pair arrangement, dimensioned 62 mm OD and 34.5 mm overall width for the pair.On the SKF nameplate, 30206-DF reads as base 30206 in a /DF matched execution — the suffix is part of the order number because a matched set is ground for a specific axial clearance and cannot be assembled from loose single bearings. In the face-to-face (X) arrangement the load lines of the two bearings converge toward the shaft axis: the set tolerates shaft deflection and thermal growth better than a back-to-back pair, but is less stiff against overturning moments. The 34.5 mm overall width of 30206-DF is the axial space the pair occupies. Catalogue mass 480 g covers both bearings and the ground spacer of 30206-DF; keep the set complete — substituting one bearing or a non-ground spacer destroys the factory clearance. Dimensional interchange map: within its boundary plan the 30×62×34.5 mm envelope of 30206-DF is fixed, so shoulder, spacer and seal drawings can be dimensioned straight from the catalogue table. Thermal behaviour of the pair: heat generated in the 30 mm bore cones flows along the shaft and changes the setting; the /DF clearance class is chosen for the catalogue speed range 7,500–11,000 r/min, so re-select the clearance class if the application runs hotter. Do not separate 30206-DF into single-bearing service stock — as individual bearings the components are not interchangeable with catalogue single-row executions because the rings are ground for the set.
Typical equipment & failure modes
Common applications
- machine-tool spindles
- belt-driven fan and blower shafts
- axle-boxes in material-handling equipment
- machine-tool spindles
Known failure patterns
- axial overload spalling at the roller-rib contact beyond the single-row thrust rating
- false brinelling on idle paired sets exposed to machine vibration
- pressed-steel cage wear or fracture after prolonged running above the limiting speed
- mounting score marks when the cone is cocked over the shaft keyway or a burr
- electrical pitting on VFD-driven shafts without grounding protection
Selection pitfalls — read before you substitute
- Replace 30206-DF as a complete set: pairing a new bearing with a worn partner leaves the clearance undefined even when the designation matches.
- Setting is built into 30206-DF; the classic field error is re-adjusting a matched pair as if it were two loose single bearings, which destroys the /DF clearance class.
- Clamp the 30206-DF pair axially through the cones, never through the rollers; pressing force across the roller complement brinells the raceways of both bearings at once.
- The 85.7/88 kN ratings are SKF catalogue 17000 values for this execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification.
- Quote the full SKF 30206/DF designation when purchasing — base-number-only orders are ambiguous across executions and variants.
Frequently asked questions
What are the dimensions and catalogue data of 30206-DF?
The SKF 30206/DF is a matched pair of single-row tapered roller bearings in face-to-face (X) matched pair arrangement with 30 mm bore, 62 mm outer diameter and 34.5 mm overall width (1.181 × 2.441 × 1.358 in). From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 85.7 kN, C0 88 kN, fatigue load limit Pu 9.65 kN, reference speed 7,500 r/min, limiting speed 11,000 r/min, mass about 0.48 kg.
What does the /DF suffix on 30206-DF mean?
The base 30206 is the ISO 355 single-row bearing; the /DF suffix marks the matched-set execution — the arrangement (face-to-face (X)), the ground spacer and the factory-set axial clearance class. A matched set cannot be assembled from loose single bearings; quote the full designation when ordering.
Are the C and C0 ratings of 30206-DF for one bearing or the pair?
They are for the complete matched pair: C 85.7 kN dynamic and C0 88 kN static already include load sharing between the two bearings. Do not halve them for single-bearing checks, and do not compare them directly with the single-row 30206 table values.
Can 30206-DF be adjusted like two loose tapered bearings?
No — the axial clearance is set at the factory by selective spacer grinding. Mounting work is limited to clean seats, correct fits (k5 on a rotating 30 mm shaft) and axial clamping through the cones; re-setting in the field destroys the matched clearance class.
When should a face-to-face (X) matched set be chosen?
Choose the face-to-face (X) set where the shaft grows thermally or alignment is imperfect — the converging load lines tolerate deflection. It is the default choice for wheel hubs and general gearbox shafts at the 30 mm bore.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants on 2026-09-29. Read our editorial & correction policy.