30210-DF bearing: complete specifications & equivalents

The 30210-DF is a ISO 355 radial bearing sized 50 x 90 x 43.5 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 90 mm d = 50 B = 43.5 mm side section front view
Principal dimensions: bore d 50 mm, outer diameter D 90 mm, width B 43.5 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 50 mm
Outer diameter D 90 mm
Width B 43.5 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 160 kN
Basic static load rating C0 183 kN
Fatigue load limit Pu 20.8 kN
Reference speed (thermal) 4800 rpm
Limiting speed (mechanical) 7500 rpm
Operating temperature -40 to +120 °C
Mass 1100 g
Manufacturer designation SKF 30210/DF
Standard ISO 355
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants
Last verified 2026-09-29

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants) · extracted 2026-09-29

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & matched-df-series range

Bore d1.969 in
Outer diameter D3.543 in
Width B1.713 in
ISO bore code10
Radial section height (D−d)/220 mm
Smallest bore in matched-df-series25 mm
Largest outer diameter in matched-df-series540 mm
Width range across matched-df-series34.5–280 mm
Bore position in matched-df-series (smallest first)6 of 35
Bore above smallest matched-df-series size25 mm

Mounting, setting & life for 30210-DF

Fits & mounting

  • Tapered bearings are separable: press the cup square into the housing and fit the cone on the shaft — usually an interference fit on both seats in wheel/hub positions.
  • Mount the cone by induction heating (max 120 °C); never strike the cage or rollers directly.
  • Shaft and housing shoulders must clear the ring chamfers so the cone and cup seat fully against their faces.

Setting — the step deep-groove bearings never need

  • After seating, set the assembly to a defined end play or preload with the locknut/shim arrangement; locknut torque seats the parts — it is not the final adjustment.
  • General free-running positions: back the nut off while measuring with a dial indicator to a small end play (commonly around 0.05–0.15 mm for medium metric hubs — follow the OEM value).
  • Pinions and stiff arrangements run a controlled preload; too much preload is the classic cause of early spalling and heat.
  • Sealed factory-set units exist for specific designations — the open 30210-DF assumes the application sets and lubricates it.

Lubrication

Open TRBs are lubricated by the application. Fill the bearing with grease (typically around one third to one half of the free cavity — overpacking a TRB causes churning heat) and provide a relubrication path; intervals depend on contamination and temperature, not on catalogue rating alone.

Why the equivalent load matters more here

TRBs carry combined radial and axial loads, so the dynamic equivalent load P is computed with the bearing's e, X and Y factors for the actual thrust ratio — using the radial load alone over-estimates life badly.

Worked L10 life example (illustrative duty)

For roller bearings the life exponent is p = 10/3: L10h = (C/P)10/3 · 106 / (60·n). Taking an example equivalent load P = 32 kN (20% of C) at n = 1,500 r/min — substitute the real P from the X/Y calculation:

C = 160.0 kN → L10h ≈ 2,375 hours

Choosing a series at the same 50 mm bore

SeriesOpen executionOD × width TC (kN)C0 (kN)Limiting speed (r/min)
320xx3201080 × 2075.094.010,500
302xx3021090 × 21.7593.191.57,500
322xx3221090 × 24.75104.0110.09,700
332xx3321090 × 32142.0160.07,000
303xx30310D110 × 29.25126.0130.03,200
323xx32310C110 × 42.25178.0220.03,500
313xx31310110 × 29.25131.0120.06,000

Different series at the same bore are not drop-in swaps — OD, width and contact angle all change — and a cone number alone never identifies a complete set. Verify matches per the cross-reference levels guide; envelope variants are on the 50×90×43.5 envelope page.

Cross references & equivalents

Equivalent modelBrandMatch levelNote
30210 ISO 15 full
Dimensions and internal design equivalent — standard interchange.
ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier.
30210-NTN NTN verify
Commonly quoted cross reference; confirm against the target catalog before ordering.
Model-number interchange per ISO 15; confirm dimensions, sealing and ratings in the supplier catalogue.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 30210-DF model number is decoded

Face-to-face matching puts the small rib ends outward, so the pressure cones cross inside the pair; 30210-DF therefore runs cooler where the shaft expands axially, at the price of lower moment stiffness than an O-arrangement of the same 50 mm bore. Dividing the pair C 160 kN by the 50 mm bore gives 3.20 kN per millimetre of journal for the complete arrangement — a density metric that compares matched sets across the face-to-face (X) matched pair family. Operating context for the 50 mm bore: a shaft of this diameter typically runs in the medium-bore band of industrial duty, and the 90 mm OD places the housing shoulder near 98 mm outer abutment. When a matched /DF set like 30210-DF is replaced, replace the whole set: mixing a new bearing with a worn partner from the old set leaves the clearance and load sharing of the pair undefined. A matched /DF set needs no setting adjustment at mounting: the clearance is built in; the assembler's job is clean seats, correct fits (k5 on a 50 mm rotating shaft) and square abutments.In SKF catalogue PUB BU/P1 17000, 30210-DF appears as SKF 30210/DF: a matched face-to-face (X) matched pair pair for a 50 mm shaft, rated as a set at C 160 kN and C0 183 kN.On the SKF nameplate, 30210-DF reads as base 30210 in a /DF matched execution — the suffix is part of the order number because a matched set is ground for a specific axial clearance and cannot be assembled from loose single bearings.

Typical equipment & failure modes

Common applications

  • axle-boxes in material-handling equipment
  • automotive and light-truck wheel hubs
  • industrial gearbox shafts and reducers
  • pump and compressor shafts

Known failure patterns

  • thermal preload runaway in an O-arrangement pair when inner-ring heat expands the setting
  • roller large-end smearing against the cone rib after EP lubricant film failure
  • cage pocket scoring when the bearing starts cold with grease of too-high base-oil viscosity
  • hard-particle indentation of the tapered raceway in unfiltered oil
  • rolling-contact fatigue spalling after the rated L10 life is exceeded

Selection pitfalls — read before you substitute

  • Spacer faces must stay parallel within the set's own tolerance; a tilted spacer in 30210-DF concentrates reversing thrust on one bearing and shows up as one-sided raceway wear.
  • Setting is built into 30210-DF; the classic field error is re-adjusting a matched pair as if it were two loose single bearings, which destroys the /DF clearance class.
  • Clamp the 30210-DF pair axially through the cones, never through the rollers; pressing force across the roller complement brinells the raceways of both bearings at once.
  • The 160/183 kN ratings are SKF catalogue 17000 values for this execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification.
  • Quote the full SKF 30210/DF designation when purchasing — base-number-only orders are ambiguous across executions and variants.

Frequently asked questions

What are the dimensions and catalogue data of 30210-DF?

The SKF 30210/DF is a matched pair of single-row tapered roller bearings in face-to-face (X) matched pair arrangement with 50 mm bore, 90 mm outer diameter and 43.5 mm overall width (1.969 × 3.543 × 1.713 in). From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 160 kN, C0 183 kN, fatigue load limit Pu 20.8 kN, reference speed 4,800 r/min, limiting speed 7,500 r/min, mass about 1.10 kg.

What does the /DF suffix on 30210-DF mean?

The base 30210 is the ISO 355 single-row bearing; the /DF suffix marks the matched-set execution — the arrangement (face-to-face (X)), the ground spacer and the factory-set axial clearance class. A matched set cannot be assembled from loose single bearings; quote the full designation when ordering.

Are the C and C0 ratings of 30210-DF for one bearing or the pair?

They are for the complete matched pair: C 160 kN dynamic and C0 183 kN static already include load sharing between the two bearings. Do not halve them for single-bearing checks, and do not compare them directly with the single-row 30210 table values.

Can 30210-DF be adjusted like two loose tapered bearings?

No — the axial clearance is set at the factory by selective spacer grinding. Mounting work is limited to clean seats, correct fits (k5 on a rotating 50 mm shaft) and axial clamping through the cones; re-setting in the field destroys the matched clearance class.

When should a face-to-face (X) matched set be chosen?

Choose the face-to-face (X) set where the shaft grows thermally or alignment is imperfect — the converging load lines tolerate deflection. It is the default choice for wheel hubs and general gearbox shafts at the 50 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants on 2026-09-29. Read our editorial & correction policy.