190×400×78 mm bearings

14 models from 3 brands across 3 types share this ISO 15 envelope: 190 mm bore, 400 mm outside diameter, 78 mm width (7.480×15.748×3.071 in), 105 mm radial section.

14 models fit this space 3 brands 14 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6338 Deep Groove Ball SKF open CN 371 430 42000
6338-M Deep Groove Ball SKF open CN 371 430 47500
6338-NSK Deep Groove Ball NSK open CN 390 415 49700
6338-NTN Deep Groove Ball NTN open CN 395 415 41000
7338 Angular Contact Ball NTN open CN 475 585 47000
7338-BCBM Angular Contact Ball SKF open CN 442 600 48500
7338B Angular Contact Ball NTN open CN 430 535 47000
N338 Cylindrical Roller NTN open CN 1080 1260 48300
NF338 Cylindrical Roller NTN open CN 1080 1260 48300
NJ338 Cylindrical Roller NTN open CN 1080 1260 48300
NU338 Cylindrical Roller NTN open CN 1080 1260 48300
NU338-ECM Cylindrical Roller SKF open CN 1140 1500 50000
NUP338 Cylindrical Roller NTN open CN 1080 1260 48300
QJ-338-N2MA Angular Contact Ball SKF open CN 702 1160 49000

Note: catalogue dynamic load ratings for this envelope span 371.0– 1140.0 kN — a 207% spread between designs in the very same 190×400×78 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 190 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6338, 6338-M, 6338-NSK, 6338-NTN, 7338, 7338-BCBM, 7338B, N338, NF338, NJ338, NU338, NU338-ECM, NUP338, QJ-338-N2MA.

Frequently asked questions

Are all 190×400×78 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 190 mm bore, 400 mm OD, 78 mm width (7.480×15.748×3.071 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 14 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 190×400×78?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 190×400×78 mm in inches?

190×400×78 mm converts to 7.480×15.748×3.071 in, with a 105 mm (4.134 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6338, 6338-M, 6338-NSK mount in the same space despite different internal designs.