6338-M (brass cage) bearing: complete specifications & equivalents

The 6338-M is a ISO 15 radial bearing sized 190 x 400 x 78 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 400 mm d = 190 B = 78 mm side section front view
Principal dimensions: bore d 190 mm, outer diameter D 400 mm, width B 78 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 190 mm
Outer diameter D 400 mm
Width B 78 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 371 kN
Basic static load rating C0 430 kN
Fatigue load limit Pu 10.8 kN
Reference speed (thermal) 3400 rpm
Limiting speed (mechanical) 3000 rpm
Operating temperature -40 to +120 °C
Mass 47500 g
Manufacturer designation 6338 M
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6300-series range

Bore d7.48 in
Outer diameter D15.748 in
Width B3.071 in
ISO bore code38
Radial section height (D−d)/2105 mm
Smallest bore in 6300-series2 mm
Largest outer diameter in 6300-series500 mm
Width range across 6300-series3–95 mm
Bore position in 6300-series (smallest first)37 of 40
Bore above smallest 6300-series size188 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
6338-NSK NSK full
Dimensions and internal design equivalent — standard interchange.
NSK counterpart NSK 6338 on the same 190×400×78 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6338-NTN NTN full
Dimensions and internal design equivalent — standard interchange.
NTN counterpart 6338 on the same 190×400×78 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6338 SKF full
Dimensions and internal design equivalent — standard interchange.
SKF SKF 6338 (open arrangement) shares the 190×400×78 mm envelope with ratings within 10 % — execution variant of the same size; boundary dimensions interchangeable.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6338-M model number is decoded

In the 6300-series, the last two digits encode the bore: 6338 carries code 38 = 190 mm (code × 5). The envelope is 190×400×78 mm (7.48×15.748×3.071 in) with a 105.0 mm radial section height, C 371 kN, C0 430 kN and Pu 10.8 kN. The open 6338 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 3000 r/min, catalogue mass 47500 g.

Typical equipment & failure modes

Common applications

  • large industrial gearboxes
  • heavy conveyor drives
  • hoists and winches
  • industrial fans and blowers

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • raceway smearing under marginal lubrication at start-up
  • electrical pitting in VFD-driven motors without shaft grounding

Selection pitfalls — read before you substitute

  • Do not preload 6338-M to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • Do not preload 6338-M to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • The M suffix on 6338-M denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 47500 g quoted mass includes the heavier cage.
  • Open 6338-M needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 6338-M; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Catalogue ratings for 6338-M (C 371 kN, C0 430 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.
  • Sealed SKF units are filled with a lithium-based grease for general service; food-grade, low-temperature and high-temperature fills are order options and are not field-interchangeable once the unit is sealed.

Frequently asked questions

What are the dimensions of 6338-M?

The SKF 6338 M measures 190 mm bore × 400 mm OD × 78 mm width (7.48 × 15.748 × 3.071 in), mass about 47500 g. It is open, with no shields or seals.

How does the bore code in 6338 work?

The final two digits of 6338 are bore code 38, multiplied by 5 to give 190 mm.

How heavy is 6338-M?

Catalogue mass is 47500 g for 6338 M; seal and cage executions of the same envelope differ by a few grams.

What internal clearance does 6338-M have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 6338-M be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.