630-8-2RS bearing: complete specifications & equivalents

The 630-8-2RS is a ISO 15 radial bearing sized 8 x 22 x 11 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 22 mm d = 8 B = 11 mm side section front view
Principal dimensions: bore d 8 mm, outer diameter D 22 mm, width B 11 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 8 mm
Outer diameter D 22 mm
Width B 11 mm
Material GCr15
Seal / shield 2RS
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 3.45 kN
Basic static load rating C0 1.37 kN
Fatigue load limit Pu 0.057 kN
Limiting speed (mechanical) 22000 rpm
Operating temperature -40 to +120 °C
Mass 16 g
Manufacturer designation 630/8-2RS1
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6300-series range

Bore d0.315 in
Outer diameter D0.866 in
Width B0.433 in
ISO bore code—
Radial section height (D−d)/27 mm
Smallest bore in 6300-series2 mm
Largest outer diameter in 6300-series500 mm
Width range across 6300-series3–95 mm
Bore position in 6300-series (smallest first)4 of 40
Bore above smallest 6300-series size6 mm

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 630-8-2RS model number is decoded

In the miniature 6300-series, the bore is written directly after the slash as 8 mm (bores below 10 mm use the slash spelling). The envelope is 8×22×11 mm (0.315×0.866×0.433 in) with a 7.0 mm radial section height, C 3.45 kN, C0 1.37 kN and Pu 0.057 kN. SKF catalogues the sealed execution as 630/8-2RS1: two contact elastomer lips (2RS1/2RSH spelling) over a lifetime grease fill; the lips add drag, and no reference (thermal) speed is published. Limiting speed 22000 r/min, catalogue mass 16 g.

Typical equipment & failure modes

Common applications

  • small pumps
  • office equipment
  • fractional-horsepower motors
  • small fans and blowers

Known failure patterns

  • contact-seal lip hardening and pre-grease loss after long high-temperature service
  • grease-life expiry inside the sealed-for-life cavity, which has no relubrication path
  • rolling-contact fatigue spalling once the catalogue L10 life is exceeded
  • brinelling from static overload or hammer blows during mounting

Selection pitfalls — read before you substitute

  • Assign interference to the rotating ring: on a conventional shaft-mounted 8 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
  • Fillet radii must clear the 630-8-2RS chamfer so the 11 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • Contact seals make 630-8-2RS slower than the open 630/8 (limiting 22000 r/min) and forbid solvent washing, which destroys the lifetime grease.
  • Do not pry the caps off 630-8-2RS to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
  • Do not preload 630-8-2RS to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • Clearance suffixes follow the seal code in the designation stack (e.g. 630/8-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • A replacement 630/8 should go onto inspected seats only: SKF mounting guidance calls for clean, burr-free journals within tolerance, since a large share of early failures traces back to damaged or worn seats.
  • Where two 630/8 bearings share one shaft in a preloaded or matched arrangement, order both from the same production lot; catalogue figures describe a single bearing, not a matched set.

Frequently asked questions

What are the dimensions of 630-8-2RS?

The SKF 630/8-2RS1 measures 8 mm bore × 22 mm OD × 11 mm width (0.315 × 0.866 × 0.433 in), mass about 16 g. It has two contact rubber seals and a lifetime grease fill.

Why is there a slash in the designation 630/8-2RS1?

The slash writes a bore that falls outside the two-digit code table: 630/8 means 8 mm bore. The site slug 630-8-2RS replaces the slash with a hyphen.

How heavy is 630-8-2RS?

Catalogue mass is 16 g for 630/8-2RS1; seal and cage executions of the same envelope differ by a few grams.

What internal clearance does 630-8-2RS have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 630-8-2RS be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.