63-28 bearing: complete specifications & equivalents

The 63-28 is a ISO 15 radial bearing sized 28 x 68 x 18 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 68 mm d = 28 B = 18 mm side section front view
Principal dimensions: bore d 28 mm, outer diameter D 68 mm, width B 18 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 28 mm
Outer diameter D 68 mm
Width B 18 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 25.1 kN
Basic static load rating C0 13.7 kN
Fatigue load limit Pu 0.585 kN
Reference speed (thermal) 22000 rpm
Limiting speed (mechanical) 14000 rpm
Operating temperature -40 to +120 °C
Mass 300 g
Manufacturer designation 63/28
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6300-series range

Bore d1.102 in
Outer diameter D2.677 in
Width B0.709 in
ISO bore code—
Radial section height (D−d)/220 mm
Smallest bore in 6300-series2 mm
Largest outer diameter in 6300-series500 mm
Width range across 6300-series3–95 mm
Bore position in 6300-series (smallest first)12 of 40
Bore above smallest 6300-series size26 mm

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 63-28 model number is decoded

In the large-bore 6300-series, the bore is written directly after the slash as 28 mm (large thin-section bores use the slash spelling instead of the two-digit code). The envelope is 28×68×18 mm (1.102×2.677×0.709 in) with a 20.0 mm radial section height, C 25.1 kN, C0 13.7 kN and Pu 0.585 kN. The open 63/28 carries no shields or seals and relies on application lubrication and external sealing. Limiting speed 14000 r/min, catalogue mass 300 g.

Typical equipment & failure modes

Common applications

  • garden machinery
  • textile machines
  • electric motors
  • centrifugal pumps

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • raceway smearing under marginal lubrication at start-up
  • electrical pitting in VFD-driven motors without shaft grounding

Selection pitfalls — read before you substitute

  • Fillet radii must clear the 63-28 chamfer so the 18 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • Mount by heating the inner ring (max 120 °C) — driving 63-28 home through the outer ring or balls brinells the raceways.
  • Open 63-28 needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 63-28; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Catalogue ratings for 63-28 (C 25.1 kN, C0 13.7 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • Mount by heating the inner ring (max 120 °C) — driving 63-28 home through the outer ring or balls brinells the raceways.
  • A replacement 63/28 should go onto inspected seats only: SKF mounting guidance calls for clean, burr-free journals within tolerance, since a large share of early failures traces back to damaged or worn seats.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.

Frequently asked questions

What are the dimensions of 63-28?

The SKF 63/28 measures 28 mm bore × 68 mm OD × 18 mm width (1.102 × 2.677 × 0.709 in), mass about 300 g. It is open, with no shields or seals.

Why is there a slash in the designation 63/28?

The slash writes a bore that falls outside the two-digit code table: 63/28 means 28 mm bore. The site slug 63-28 replaces the slash with a hyphen.

What internal clearance does 63-28 have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 63-28 be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 63-28 take?

Catalogue values for 63/28: dynamic C 25.1 kN, static C0 13.7 kN, fatigue limit Pu 0.585 kN. Use C in life calculation and C0 for static checks at 28 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.