62311-2RS bearing: complete specifications & equivalents

The 62311-2RS is a ISO 15 radial bearing sized 55 x 120 x 43 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 120 mm d = 55 B = 43 mm side section front view
Principal dimensions: bore d 55 mm, outer diameter D 120 mm, width B 43 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 55 mm
Outer diameter D 120 mm
Width B 43 mm
Material GCr15
Seal / shield 2RS
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 71.5 kN
Basic static load rating C0 45 kN
Fatigue load limit Pu 1.9 kN
Limiting speed (mechanical) 3800 rpm
Operating temperature -40 to +120 °C
Mass 2050 g
Manufacturer designation 62311-2RS1
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 62300-series range

Bore d2.165 in
Outer diameter D4.724 in
Width B1.693 in
ISO bore code11
Radial section height (D−d)/232.5 mm
Smallest bore in 62300-series10 mm
Largest outer diameter in 62300-series150 mm
Width range across 62300-series17–51 mm
Bore position in 62300-series (smallest first)12 of 15
Bore above smallest 62300-series size45 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
4311-ATN9 SKF partial
Main dimensions match; tolerances, seals or internal clearance differ.
Same 55×120×43 mm envelope as SKF 4311 ATN9, but catalogue C/C0 differ (71.5/45 kN vs 97.5/83 kN) — envelope match only after a load check.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 62311-2RS model number is decoded

The 62300-series is the wide-section counterpart of the standard deep-groove family (extra width code built into the designation); the last two digits encode the bore: 62311 carries code 11 = 55 mm (code × 5). The envelope is 55×120×43 mm (2.165×4.724×1.693 in) with a 32.5 mm radial section height, C 71.5 kN, C0 45 kN and Pu 1.9 kN. SKF catalogues the sealed execution as 62311-2RS1: two contact elastomer lips (2RS1/2RSH spelling) over a lifetime grease fill; the lips add drag, and no reference (thermal) speed is published. Limiting speed 3800 r/min, catalogue mass 2050 g.

Typical equipment & failure modes

Common applications

  • gearboxes and speed reducers
  • centrifugal and positive-displacement pumps
  • material-handling equipment
  • industrial fans

Known failure patterns

  • contact-seal lip hardening and pre-grease loss after long high-temperature service
  • grease-life expiry inside the sealed-for-life cavity, which has no relubrication path
  • brinelling from static overload or hammer blows during mounting
  • false brinelling from vibration while the shaft stands idle

Selection pitfalls — read before you substitute

  • Assign interference to the rotating ring: on a conventional shaft-mounted 55 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
  • Assign interference to the rotating ring: on a conventional shaft-mounted 55 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
  • Contact seals make 62311-2RS slower than the open 62311 (limiting 3800 r/min) and forbid solvent washing, which destroys the lifetime grease.
  • Do not pry the caps off 62311-2RS to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
  • Assign interference to the rotating ring: on a conventional shaft-mounted 55 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
  • Deep-groove geometry tolerates only minutes of misalignment; if the 120 mm housing bore cannot be aligned, move to a self-aligning bearing rather than shimming 62311-2RS.
  • Where two 62311 bearings share one shaft in a preloaded or matched arrangement, order both from the same production lot; catalogue figures describe a single bearing, not a matched set.
  • Sealed SKF units are filled with a lithium-based grease for general service; food-grade, low-temperature and high-temperature fills are order options and are not field-interchangeable once the unit is sealed.

Frequently asked questions

What are the dimensions of 62311-2RS?

The SKF 62311-2RS1 measures 55 mm bore × 120 mm OD × 43 mm width (2.165 × 4.724 × 1.693 in), mass about 2050 g. It has two contact rubber seals and a lifetime grease fill.

How does the bore code in 62311 work?

The final two digits of 62311 are bore code 11, multiplied by 5 to give 55 mm.

What is the speed rating of 62311-2RS?

SKF publishes only the 3800 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern.

What is the difference between 62311-2RS and a same-bore 62-series bearing?

Section height differs: 62311-2RS has a 32.5 mm radial section and C 71.5 kN; always match d, D and B — same bore alone never makes two bearings interchangeable.

Which fits should I use for 62311-2RS?

With a rotating inner ring use roughly k5 on the shaft and H7 in the 120 mm housing; reverse the interference if the outer ring rotates.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.