62310-2RS bearing: complete specifications & equivalents

The 62310-2RS is a ISO 15 radial bearing sized 50 x 110 x 40 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 110 mm d = 50 B = 40 mm side section front view
Principal dimensions: bore d 50 mm, outer diameter D 110 mm, width B 40 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 50 mm
Outer diameter D 110 mm
Width B 40 mm
Material GCr15
Seal / shield 2RS
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 61.8 kN
Basic static load rating C0 38 kN
Fatigue load limit Pu 1.6 kN
Limiting speed (mechanical) 4300 rpm
Operating temperature -40 to +120 °C
Mass 1600 g
Manufacturer designation 62310-2RS1
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 62300-series range

Bore d1.969 in
Outer diameter D4.331 in
Width B1.575 in
ISO bore code10
Radial section height (D−d)/230 mm
Smallest bore in 62300-series10 mm
Largest outer diameter in 62300-series150 mm
Width range across 62300-series17–51 mm
Bore position in 62300-series (smallest first)11 of 15
Bore above smallest 62300-series size40 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
4310-ATN9 SKF partial
Main dimensions match; tolerances, seals or internal clearance differ.
Same 50×110×40 mm envelope as SKF 4310 ATN9, but catalogue C/C0 differ (61.8/38 kN vs 81.9/69.5 kN) — envelope match only after a load check.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 62310-2RS model number is decoded

The 62300-series is the wide-section counterpart of the standard deep-groove family (extra width code built into the designation); the last two digits encode the bore: 62310 carries code 10 = 50 mm (code × 5). The envelope is 50×110×40 mm (1.969×4.331×1.575 in) with a 30.0 mm radial section height, C 61.8 kN, C0 38 kN and Pu 1.6 kN. SKF catalogues the sealed execution as 62310-2RS1: two contact elastomer lips (2RS1/2RSH spelling) over a lifetime grease fill; the lips add drag, and no reference (thermal) speed is published. Limiting speed 4300 r/min, catalogue mass 1600 g.

Typical equipment & failure modes

Common applications

  • machine tool auxiliaries
  • agricultural gearboxes
  • industrial electric motors
  • gearboxes and speed reducers

Known failure patterns

  • contact-seal lip hardening and pre-grease loss after long high-temperature service
  • grease-life expiry inside the sealed-for-life cavity, which has no relubrication path
  • cage damage from running beyond the limiting speed
  • raceway smearing under marginal lubrication at start-up

Selection pitfalls — read before you substitute

  • Clearance suffixes follow the seal code in the designation stack (e.g. 62310-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • Fillet radii must clear the 62310-2RS chamfer so the 40 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • Contact seals make 62310-2RS slower than the open 62310 (limiting 4300 r/min) and forbid solvent washing, which destroys the lifetime grease.
  • Do not pry the caps off 62310-2RS to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
  • Do not preload 62310-2RS to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • Clearance suffixes follow the seal code in the designation stack (e.g. 62310-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • A replacement 62310 should go onto inspected seats only: SKF mounting guidance calls for clean, burr-free journals within tolerance, since a large share of early failures traces back to damaged or worn seats.
  • Where two 62310 bearings share one shaft in a preloaded or matched arrangement, order both from the same production lot; catalogue figures describe a single bearing, not a matched set.

Frequently asked questions

What are the dimensions of 62310-2RS?

The SKF 62310-2RS1 measures 50 mm bore × 110 mm OD × 40 mm width (1.969 × 4.331 × 1.575 in), mass about 1600 g. It has two contact rubber seals and a lifetime grease fill.

How does the bore code in 62310 work?

The final two digits of 62310 are bore code 10, multiplied by 5 to give 50 mm.

What internal clearance does 62310-2RS have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 62310-2RS be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 62310-2RS take?

Catalogue values for 62310-2RS1: dynamic C 61.8 kN, static C0 38 kN, fatigue limit Pu 1.6 kN. Use C in life calculation and C0 for static checks at 50 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.