[
  {
    "sku": "51410",
    "brand": "NTN",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 43,
    "seal_type": "open",
    "dynamic_load_kN": 159,
    "static_load_kN": 318,
    "fatigue_load_limit_kN": 14.2,
    "limiting_speed_rpm": 1400,
    "speed_oil_rpm": 2000,
    "weight_g": 1970,
    "manufacturer_designation": "51410",
    "standard": "ISO 104",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [],
    "naming_rule_text": "In the 51400-series (ISO 104 dimension series) the leading digits 514 mark a single-direction thrust ball bearing and the last two digits encode the bore: 51410 carries bore code 10 = 50 mm. The ISO 104 boundary dimensions are 50 mm bore, 110 mm outside diameter and 43 mm height. Two flat washers (shaft and housing) and a ball cage assembly allow the bearing to carry pure axial load in one direction while accommodating minor misalignment.",
    "applications": [
      "gearbox axial load management",
      "conveyor drive thrust washers",
      "agricultural equipment spindle thrust",
      "industrial fan axial restraint"
    ],
    "failure_modes": [
      "washer seat fretting from a loose housing or shaft fit",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "At a 50 mm bore, check shaft shoulder runout before fitting 51410; a skewed shoulder tilts the shaft washer and concentrates load on a few balls.",
      "The 514xx heavy section at 50 mm bore (110 mm OD) is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 511/512 there.",
      "Do not use a thrust ball bearing for combined radial-axial loads — pair it with a radial bearing (deep-groove or spherical roller) for the radial component.",
      "Thrust ball bearings carry axial load only — never apply radial load to 51410; the flat washers will skid and score."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 51410 thrust ball bearing?",
        "a": "A 51410 thrust ball bearing has a 50 mm bore, 110 mm outside diameter and 43 mm height, per ISO 104 boundary dimensions. It consists of a shaft washer, housing washer and ball cage assembly."
      },
      {
        "q": "How does the 51410 bore code work?",
        "a": "The last two digits of 51410 are bore code 10, giving 10 × 5 = 50 mm bore. The 110 mm outside diameter and 43 mm height follow the ISO 104 dimension series, not the bore code alone."
      },
      {
        "q": "Can a 51410 thrust ball bearing carry radial load?",
        "a": "No. Single-direction thrust ball bearings carry axial load only. Any radial component must be supported by a separate radial bearing (deep-groove, cylindrical roller or spherical roller)."
      },
      {
        "q": "How does the 51400 compare with other thrust series at the same 50 mm bore?",
        "a": "The 514xx is the heavy section: 110×43 mm, 30.0 mm radial section at 50 mm bore — the highest-capacity single-direction thrust option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "51410-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "51100",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51100",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 10,
    "D_mm": 24,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 10,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.63,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "speed_oil_rpm": 9500,
    "weight_g": 21,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The light-section 51100 thrust family entry 51100 stacks a shaft washer, ball-and-cage set and housing washer into 9 mm of height over a 10 mm bore. The designation is 511 is the dimension series (light-section 51100 thrust family) plus the bore code 00 maps to the 10 mm bore by the standard table. Catalogue mass is about 21 g for the full washer-and-cage stack. The 10/24/9 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 24 mm OD already tilts the raceway and concentrates the 14 kN static capacity on a few balls. ",
    "applications": [
      "valve actuator and gearbox thrust seats",
      "food-machine vertical auger shafts",
      "laboratory centrifuge and mixer thrust ends",
      "small vertical pump and agitator thrust positions"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "Small thrust washers of 10 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 10 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 10 kN never saves a bearing that is running too lightly loaded at 6,700 r/min.",
      "The 6,700 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The Ca 10/C0a 14 kN ratings and 0.63 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51100; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51100?",
        "a": "51100 is a single-direction thrust ball bearing to ISO 104: 10 mm shaft-washer bore, 24 mm outside diameter, 9 mm stack height (0.394 x 0.945 x 0.354 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 10 kN, C0a 14 kN and a 0.63 kN fatigue load limit Pu; the grease limiting speed is 6,700 r/min and the oil rating 9,500 r/min; mass about 21 g."
      },
      {
        "q": "How is the 51100 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); the bore code 00 maps to the 10 mm bore by the standard table. The 24 mm OD and 9 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51100 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51100?",
        "a": "At the 6,700 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51100?",
        "a": "The 10/24/9 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 10 kN / C0a 14 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51100-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51100"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51200",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51200",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 10,
    "D_mm": 26,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 17.1,
    "fatigue_load_limit_kN": 0.77,
    "limiting_speed_rpm": 5800,
    "max_rpm": 5800,
    "speed_oil_rpm": 8300,
    "weight_g": 30,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51200 is the 10 mm member of NTN's medium-section 51200 thrust family: 26 mm across the washers, 11 mm tall. NTN builds the number from 512 is the dimension series (medium-section 51200 thrust family); the bore code 00 maps to the 10 mm bore by the standard table. At 11 mm of height the stack is compact for the 10 mm bore class, trading section height for the medium-section load level. Against a thrust roller bearing of the same 10 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. The shaft washer (bore 10 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "automotive steering-gear and clutch release points",
      "small crane hook and swivel-joint thrust supports",
      "valve actuator and gearbox thrust seats",
      "food-machine vertical auger shafts"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "Small thrust washers of 10 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 10 mm bore.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 12.7 kN never saves a bearing that is running too lightly loaded at 5,800 r/min.",
      "The Ca 12.7/C0a 17.1 kN ratings and 0.77 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51200; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51200?",
        "a": "51200 is a single-direction thrust ball bearing to ISO 104: 10 mm shaft-washer bore, 26 mm outside diameter, 11 mm stack height (0.394 x 1.024 x 0.433 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 12.7 kN, C0a 17.1 kN and a 0.77 kN fatigue load limit Pu; the grease limiting speed is 5,800 r/min and the oil rating 8,300 r/min; mass about 30 g."
      },
      {
        "q": "How is the 51200 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); the bore code 00 maps to the 10 mm bore by the standard table. The 26 mm OD and 11 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51200 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51200?",
        "a": "At the 5,800 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51200?",
        "a": "The 10/26/11 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 12.7 kN / C0a 17.1 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51200-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51200"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51101",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51101",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 12,
    "D_mm": 26,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 10.3,
    "static_load_kN": 15.4,
    "fatigue_load_limit_kN": 0.69,
    "limiting_speed_rpm": 6400,
    "max_rpm": 6400,
    "speed_oil_rpm": 9200,
    "weight_g": 23,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 12 x 26 x 9 mm, NTN 51101 sits in the light-section 51100 thrust family of the single-direction thrust programme. Reading the code: 511 is the dimension series (light-section 51100 thrust family), and the bore code 01 maps to the 12 mm bore by the standard table. With Ca 10.3 kN and C0a 15.4 kN, each mm of shaft bore carries about 0.86 kN of dynamic axial rating. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51101 cannot. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "laboratory centrifuge and mixer thrust ends",
      "small vertical pump and agitator thrust positions",
      "bench drill-press and tapping-machine spindles",
      "automotive steering-gear and clutch release points"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "Small thrust washers of 12 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 12 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Shock thrust above C0a 15.4 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Swapping the shaft and housing washers is an easy assembly error on the 12 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 10.3/C0a 15.4 kN ratings and 0.69 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51101; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51101?",
        "a": "51101 is a single-direction thrust ball bearing to ISO 104: 12 mm shaft-washer bore, 26 mm outside diameter, 9 mm stack height (0.472 x 1.024 x 0.354 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 10.3 kN, C0a 15.4 kN and a 0.69 kN fatigue load limit Pu; the grease limiting speed is 6,400 r/min and the oil rating 9,200 r/min; mass about 23 g."
      },
      {
        "q": "How is the 51101 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); the bore code 01 maps to the 12 mm bore by the standard table. The 26 mm OD and 9 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51101 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51101?",
        "a": "At the 6,400 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51101?",
        "a": "The 12/26/9 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 10.3 kN / C0a 15.4 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51101-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51101"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51201",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51201",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 12,
    "D_mm": 28,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 13.2,
    "static_load_kN": 19,
    "fatigue_load_limit_kN": 0.86,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "speed_oil_rpm": 8000,
    "weight_g": 34,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the medium-section 51200 thrust family, 51201 measures 12 mm through the shaft washer, 28 mm over the outside and 11 mm in assembled height. The designation is 512 is the dimension series (medium-section 51200 thrust family) plus the bore code 01 maps to the 12 mm bore by the standard table. The static margin, C0a 19 kN against Ca 13.2 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. If the duty is high speed with light thrust, check the minimum axial load formula first; a too-large thrust ball bearing fails by skid long before its Ca of 13.2 kN is ever approached. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "valve actuator and gearbox thrust seats",
      "food-machine vertical auger shafts",
      "laboratory centrifuge and mixer thrust ends",
      "small vertical pump and agitator thrust positions"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "Small thrust washers of 12 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 12 mm bore.",
      "The 5,600 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The C0a of 19 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Shock thrust above C0a 19 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 13.2/C0a 19 kN ratings and 0.86 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51201; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51201?",
        "a": "51201 is a single-direction thrust ball bearing to ISO 104: 12 mm shaft-washer bore, 28 mm outside diameter, 11 mm stack height (0.472 x 1.102 x 0.433 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 13.2 kN, C0a 19 kN and a 0.86 kN fatigue load limit Pu; the grease limiting speed is 5,600 r/min and the oil rating 8,000 r/min; mass about 34 g."
      },
      {
        "q": "How is the 51201 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); the bore code 01 maps to the 12 mm bore by the standard table. The 28 mm OD and 11 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51201 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51201?",
        "a": "At the 5,600 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51201?",
        "a": "The 12/28/11 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 13.2 kN / C0a 19 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51201-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51201"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51102",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51102",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 15,
    "D_mm": 28,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 10.5,
    "static_load_kN": 16.8,
    "fatigue_load_limit_kN": 0.76,
    "limiting_speed_rpm": 6200,
    "max_rpm": 6200,
    "speed_oil_rpm": 8800,
    "weight_g": 24,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51102 is the 15 mm member of NTN's light-section 51100 thrust family: 28 mm across the washers, 9 mm tall. Two fields make up the code — 511 is the dimension series (light-section 51100 thrust family) and the bore code 02 maps to the 15 mm bore by the standard table. Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. For a 15 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "bench drill-press and tapping-machine spindles",
      "automotive steering-gear and clutch release points",
      "small crane hook and swivel-joint thrust supports",
      "valve actuator and gearbox thrust seats"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "Small thrust washers of 15 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 15 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Single-direction means exactly that: thrust on 51102 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Single-direction means exactly that: thrust on 51102 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 10.5/C0a 16.8 kN ratings and 0.76 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51102; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51102?",
        "a": "51102 is a single-direction thrust ball bearing to ISO 104: 15 mm shaft-washer bore, 28 mm outside diameter, 9 mm stack height (0.591 x 1.102 x 0.354 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 10.5 kN, C0a 16.8 kN and a 0.76 kN fatigue load limit Pu; the grease limiting speed is 6,200 r/min and the oil rating 8,800 r/min; mass about 24 g."
      },
      {
        "q": "How is the 51102 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); the bore code 02 maps to the 15 mm bore by the standard table. The 28 mm OD and 9 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51102 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51102?",
        "a": "At the 6,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51102?",
        "a": "The 15/28/9 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 10.5 kN / C0a 16.8 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51102-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51102"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51202",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51202",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 15,
    "D_mm": 32,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 16.6,
    "static_load_kN": 24.8,
    "fatigue_load_limit_kN": 1.12,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "speed_oil_rpm": 7100,
    "weight_g": 46,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51202 is an NTN single-direction thrust ball bearing of the medium-section 51200 thrust family: 15 mm bore, 32 mm outside diameter, 12 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. Reading the code: 512 is the dimension series (medium-section 51200 thrust family), and the bore code 02 maps to the 15 mm bore by the standard table. The washer section here is 8.5 mm of radial height, and the catalogue couples it with Ca 16.6 kN / C0a 24.8 kN. Size selection ends with the minimum-load check: at the 5,000 r/min class speed, the balls need a defined axial preload to keep rolling instead of skidding. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "laboratory centrifuge and mixer thrust ends",
      "small vertical pump and agitator thrust positions",
      "bench drill-press and tapping-machine spindles",
      "automotive steering-gear and clutch release points"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "Small thrust washers of 15 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 15 mm bore.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51202 stack height of 12 mm and washer set differ from the double-direction execution.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The C0a of 24.8 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The Ca 16.6/C0a 24.8 kN ratings and 1.12 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51202; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51202?",
        "a": "51202 is a single-direction thrust ball bearing to ISO 104: 15 mm shaft-washer bore, 32 mm outside diameter, 12 mm stack height (0.591 x 1.26 x 0.472 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 16.6 kN, C0a 24.8 kN and a 1.12 kN fatigue load limit Pu; the grease limiting speed is 5,000 r/min and the oil rating 7,100 r/min; mass about 46 g."
      },
      {
        "q": "How is the 51202 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); the bore code 02 maps to the 15 mm bore by the standard table. The 32 mm OD and 12 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51202 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51202?",
        "a": "At the 5,000 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51202?",
        "a": "The 15/32/12 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 16.6 kN / C0a 24.8 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51202-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51202"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51103",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51103",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 17,
    "D_mm": 30,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 10.8,
    "static_load_kN": 18.2,
    "fatigue_load_limit_kN": 0.82,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "speed_oil_rpm": 8500,
    "weight_g": 26,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the light-section 51100 thrust family, 51103 measures 17 mm through the shaft washer, 30 mm over the outside and 9 mm in assembled height. Decoding 51103: 511 is the dimension series (light-section 51100 thrust family), with the bore code 03 maps to the 17 mm bore by the standard table. On speed, the grease limiting speed is 6,000 r/min and the oil rating 8,500 r/min. Against a thrust roller bearing of the same 17 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "small crane hook and swivel-joint thrust supports",
      "valve actuator and gearbox thrust seats",
      "food-machine vertical auger shafts",
      "laboratory centrifuge and mixer thrust ends"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "Small thrust washers of 17 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 17 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 10.8 kN never saves a bearing that is running too lightly loaded at 6,000 r/min.",
      "The C0a of 18.2 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The Ca 10.8/C0a 18.2 kN ratings and 0.82 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51103; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51103?",
        "a": "51103 is a single-direction thrust ball bearing to ISO 104: 17 mm shaft-washer bore, 30 mm outside diameter, 9 mm stack height (0.669 x 1.181 x 0.354 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 10.8 kN, C0a 18.2 kN and a 0.82 kN fatigue load limit Pu; the grease limiting speed is 6,000 r/min and the oil rating 8,500 r/min; mass about 26 g."
      },
      {
        "q": "How is the 51103 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); the bore code 03 maps to the 17 mm bore by the standard table. The 30 mm OD and 9 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51103 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51103?",
        "a": "At the 6,000 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51103?",
        "a": "The 17/30/9 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 10.8 kN / C0a 18.2 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51103-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×30×9 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51103"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51203",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51203",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 17,
    "D_mm": 35,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 17.2,
    "static_load_kN": 27.3,
    "fatigue_load_limit_kN": 1.23,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "speed_oil_rpm": 6800,
    "weight_g": 54,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51203 appears as a medium-section 51200 thrust family bearing with a 17 mm shaft washer, a 35 mm housing diameter and 12 mm of stack height. Two fields make up the code — 512 is the dimension series (medium-section 51200 thrust family) and the bore code 03 maps to the 17 mm bore by the standard table. The ball-and-cage set is separable from both washers, which is why the mounting order (shaft washer first, then cage, then housing washer) matters. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 27.3 kN class figures at the cost of OD and height. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 35 mm OD already tilts the raceway and concentrates the 27.3 kN static capacity on a few balls. ",
    "applications": [
      "bench drill-press and tapping-machine spindles",
      "automotive steering-gear and clutch release points",
      "small crane hook and swivel-joint thrust supports",
      "valve actuator and gearbox thrust seats"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "Small thrust washers of 17 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 17 mm bore.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51203 has no radial capacity at all.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51203 has no radial capacity at all.",
      "The Ca 17.2/C0a 27.3 kN ratings and 1.23 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51203; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51203?",
        "a": "51203 is a single-direction thrust ball bearing to ISO 104: 17 mm shaft-washer bore, 35 mm outside diameter, 12 mm stack height (0.669 x 1.378 x 0.472 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 17.2 kN, C0a 27.3 kN and a 1.23 kN fatigue load limit Pu; the grease limiting speed is 4,800 r/min and the oil rating 6,800 r/min; mass about 54 g."
      },
      {
        "q": "How is the 51203 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); the bore code 03 maps to the 17 mm bore by the standard table. The 35 mm OD and 12 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51203 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51203?",
        "a": "At the 4,800 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51203?",
        "a": "The 17/35/12 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 17.2 kN / C0a 27.3 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51203-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51203"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51104",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51104",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 20,
    "D_mm": 35,
    "B_mm": 10,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 14.2,
    "static_load_kN": 24.7,
    "fatigue_load_limit_kN": 1.12,
    "limiting_speed_rpm": 5200,
    "max_rpm": 5200,
    "speed_oil_rpm": 7500,
    "weight_g": 40,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51104 is an NTN single-direction thrust ball bearing of the light-section 51100 thrust family: 20 mm bore, 35 mm outside diameter, 10 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. NTN builds the number from 511 is the dimension series (light-section 51100 thrust family); 04 encodes the 20 mm bore (bore code x 5). Catalogue axial dynamic rating Ca is 14.2 kN against C0a 24.7 kN — a static/dynamic ratio of 1.74 that is the signature of a thrust raceway. If the duty is high speed with light thrust, check the minimum axial load formula first; a too-large thrust ball bearing fails by skid long before its Ca of 14.2 kN is ever approached. The shaft washer (bore 20 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "food-machine vertical auger shafts",
      "laboratory centrifuge and mixer thrust ends",
      "small vertical pump and agitator thrust positions",
      "bench drill-press and tapping-machine spindles"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "Small thrust washers of 20 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 20 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Swapping the shaft and housing washers is an easy assembly error on the 20 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The Ca 14.2/C0a 24.7 kN ratings and 1.12 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51104; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51104?",
        "a": "51104 is a single-direction thrust ball bearing to ISO 104: 20 mm shaft-washer bore, 35 mm outside diameter, 10 mm stack height (0.787 x 1.378 x 0.394 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 14.2 kN, C0a 24.7 kN and a 1.12 kN fatigue load limit Pu; the grease limiting speed is 5,200 r/min and the oil rating 7,500 r/min; mass about 40 g."
      },
      {
        "q": "How is the 51104 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 04 encodes the 20 mm bore (bore code x 5). The 35 mm OD and 10 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51104 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51104?",
        "a": "At the 5,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51104?",
        "a": "The 20/35/10 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 14.2 kN / C0a 24.7 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51104-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×35×10 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51104"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51204",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51204",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 20,
    "D_mm": 40,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 22.3,
    "static_load_kN": 37.5,
    "fatigue_load_limit_kN": 1.7,
    "limiting_speed_rpm": 4100,
    "max_rpm": 4100,
    "speed_oil_rpm": 5900,
    "weight_g": 81,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51204 belongs to the medium-section 51200 thrust family of single-direction thrust ball bearings: 20 / 40 / 14 mm (shaft bore / OD / height). Decoding 51204: 512 is the dimension series (medium-section 51200 thrust family), with 04 encodes the 20 mm bore (bore code x 5). Catalogue mass is about 81 g for the full washer-and-cage stack. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "small crane hook and swivel-joint thrust supports",
      "valve actuator and gearbox thrust seats",
      "food-machine vertical auger shafts",
      "laboratory centrifuge and mixer thrust ends"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "Small thrust washers of 20 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 20 mm bore.",
      "Swapping the shaft and housing washers is an easy assembly error on the 20 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The 4,100 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The 4,100 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The Ca 22.3/C0a 37.5 kN ratings and 1.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51204; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51204?",
        "a": "51204 is a single-direction thrust ball bearing to ISO 104: 20 mm shaft-washer bore, 40 mm outside diameter, 14 mm stack height (0.787 x 1.575 x 0.551 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 22.3 kN, C0a 37.5 kN and a 1.7 kN fatigue load limit Pu; the grease limiting speed is 4,100 r/min and the oil rating 5,900 r/min; mass about 81 g."
      },
      {
        "q": "How is the 51204 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 04 encodes the 20 mm bore (bore code x 5). The 40 mm OD and 14 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51204 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51204?",
        "a": "At the 4,100 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51204?",
        "a": "The 20/40/14 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 22.3 kN / C0a 37.5 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51204-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51204"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51105",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51105",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 42,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 19.6,
    "static_load_kN": 37,
    "fatigue_load_limit_kN": 1.68,
    "limiting_speed_rpm": 4600,
    "max_rpm": 4600,
    "speed_oil_rpm": 6500,
    "weight_g": 60,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51105 appears as a light-section 51100 thrust family bearing with a 25 mm shaft washer, a 42 mm housing diameter and 11 mm of stack height. The designation is 511 is the dimension series (light-section 51100 thrust family) plus 05 encodes the 25 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 19.6 kN rating assumes the load arrives truly axial. Size selection ends with the minimum-load check: at the 4,600 r/min class speed, the balls need a defined axial preload to keep rolling instead of skidding. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "small vertical pump and agitator thrust positions",
      "bench drill-press and tapping-machine spindles",
      "automotive steering-gear and clutch release points",
      "small crane hook and swivel-joint thrust supports"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "Small thrust washers of 25 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 25 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51105 stack height of 11 mm and washer set differ from the double-direction execution.",
      "The Ca 19.6/C0a 37 kN ratings and 1.68 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51105; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51105?",
        "a": "51105 is a single-direction thrust ball bearing to ISO 104: 25 mm shaft-washer bore, 42 mm outside diameter, 11 mm stack height (0.984 x 1.654 x 0.433 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 19.6 kN, C0a 37 kN and a 1.68 kN fatigue load limit Pu; the grease limiting speed is 4,600 r/min and the oil rating 6,500 r/min; mass about 60 g."
      },
      {
        "q": "How is the 51105 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 05 encodes the 25 mm bore (bore code x 5). The 42 mm OD and 11 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51105 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51105?",
        "a": "At the 4,600 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51105?",
        "a": "The 25/42/11 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 19.6 kN / C0a 37 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51105-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51105"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51205",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51205",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 47,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 27.8,
    "static_load_kN": 50.5,
    "fatigue_load_limit_kN": 2.28,
    "limiting_speed_rpm": 3700,
    "max_rpm": 3700,
    "speed_oil_rpm": 5300,
    "weight_g": 111,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The medium-section 51200 thrust family entry 51205 stacks a shaft washer, ball-and-cage set and housing washer into 15 mm of height over a 25 mm bore. NTN builds the number from 512 is the dimension series (medium-section 51200 thrust family); 05 encodes the 25 mm bore (bore code x 5). With Ca 27.8 kN and C0a 50.5 kN, each mm of shaft bore carries about 1.11 kN of dynamic axial rating. Choose the medium-section 51200 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "food-machine vertical auger shafts",
      "laboratory centrifuge and mixer thrust ends",
      "small vertical pump and agitator thrust positions",
      "bench drill-press and tapping-machine spindles"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "Small thrust washers of 25 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 25 mm bore.",
      "The C0a of 50.5 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Shock thrust above C0a 50.5 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 27.8/C0a 50.5 kN ratings and 2.28 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51205; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51205?",
        "a": "51205 is a single-direction thrust ball bearing to ISO 104: 25 mm shaft-washer bore, 47 mm outside diameter, 15 mm stack height (0.984 x 1.85 x 0.591 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 27.8 kN, C0a 50.5 kN and a 2.28 kN fatigue load limit Pu; the grease limiting speed is 3,700 r/min and the oil rating 5,300 r/min; mass about 111 g."
      },
      {
        "q": "How is the 51205 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 05 encodes the 25 mm bore (bore code x 5). The 47 mm OD and 15 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51205 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51205?",
        "a": "At the 3,700 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51205?",
        "a": "The 25/47/15 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 27.8 kN / C0a 50.5 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51205-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51205"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51305",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51305",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 35.5,
    "static_load_kN": 61.5,
    "fatigue_load_limit_kN": 2.77,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "speed_oil_rpm": 4600,
    "weight_g": 176,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51305 is the 25 mm member of NTN's heavy-section 51300 thrust family: 52 mm across the washers, 18 mm tall. Decoding 51305: 513 is the dimension series (heavy-section 51300 thrust family), with 05 encodes the 25 mm bore (bore code x 5). Catalogue axial dynamic rating Ca is 35.5 kN against C0a 61.5 kN — a static/dynamic ratio of 1.73 that is the signature of a thrust raceway. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 61.5 kN class figures at the cost of OD and height. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "valve actuator and gearbox thrust seats",
      "food-machine vertical auger shafts",
      "laboratory centrifuge and mixer thrust ends",
      "small vertical pump and agitator thrust positions"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "Small thrust washers of 25 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 513 heavy section buys capacity with a larger 52 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51305 stack height of 18 mm and washer set differ from the double-direction execution.",
      "Swapping the shaft and housing washers is an easy assembly error on the 25 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The Ca 35.5/C0a 61.5 kN ratings and 2.77 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51305; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51305?",
        "a": "51305 is a single-direction thrust ball bearing to ISO 104: 25 mm shaft-washer bore, 52 mm outside diameter, 18 mm stack height (0.984 x 2.047 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 35.5 kN, C0a 61.5 kN and a 2.77 kN fatigue load limit Pu; the grease limiting speed is 3,200 r/min and the oil rating 4,600 r/min; mass about 176 g."
      },
      {
        "q": "How is the 51305 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 05 encodes the 25 mm bore (bore code x 5). The 52 mm OD and 18 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51305 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51305?",
        "a": "At the 3,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51305?",
        "a": "The 25/52/18 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 35.5 kN / C0a 61.5 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51305-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51305"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51405",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51405",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 60,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 55.5,
    "static_load_kN": 89.5,
    "fatigue_load_limit_kN": 4.05,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "speed_oil_rpm": 3700,
    "weight_g": 330,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51405 is an NTN single-direction thrust ball bearing of the extra-heavy 51400 thrust family: 25 mm bore, 60 mm outside diameter, 24 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. The designation is 514 is the dimension series (extra-heavy 51400 thrust family) plus 05 encodes the 25 mm bore (bore code x 5). Catalogue mass is about 330 g for the full washer-and-cage stack. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51405 cannot. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "bench drill-press and tapping-machine spindles",
      "automotive steering-gear and clutch release points",
      "small crane hook and swivel-joint thrust supports",
      "valve actuator and gearbox thrust seats"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "Small thrust washers of 25 mm bore bend if the shaft shoulder is rough — check burrs before seating, and never press on the housing washer to drive the shaft washer home.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Shock thrust above C0a 89.5 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51405 has no radial capacity at all.",
      "The 2,600 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The Ca 55.5/C0a 89.5 kN ratings and 4.05 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51405; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51405?",
        "a": "51405 is a single-direction thrust ball bearing to ISO 104: 25 mm shaft-washer bore, 60 mm outside diameter, 24 mm stack height (0.984 x 2.362 x 0.945 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 55.5 kN, C0a 89.5 kN and a 4.05 kN fatigue load limit Pu; the grease limiting speed is 2,600 r/min and the oil rating 3,700 r/min; mass about 330 g."
      },
      {
        "q": "How is the 51405 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 05 encodes the 25 mm bore (bore code x 5). The 60 mm OD and 24 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51405 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51405?",
        "a": "At the 2,600 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51405?",
        "a": "The 25/60/24 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 55.5 kN / C0a 89.5 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51405-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×60×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51405"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51106",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51106",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 47,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 20.4,
    "static_load_kN": 42,
    "fatigue_load_limit_kN": 1.9,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "speed_oil_rpm": 6200,
    "weight_g": 69,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51106 belongs to the light-section 51100 thrust family of single-direction thrust ball bearings: 30 / 47 / 11 mm (shaft bore / OD / height). Reading the code: 511 is the dimension series (light-section 51100 thrust family), and 06 encodes the 30 mm bore (bore code x 5). NTN prints 20.4 kN axial dynamic and 42 kN axial static for this size and a 1.9 kN fatigue load limit Pu. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 42 kN class figures at the cost of OD and height. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "medium crane hook blocks and slewing jibs",
      "extruder and mixer thrust housings",
      "winch and capstan vertical shafts",
      "press and punch-machine thrust seats"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 30 mm size together from unpacking to assembly.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 30 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "The 4,300 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The 4,300 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The Ca 20.4/C0a 42 kN ratings and 1.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51106; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51106?",
        "a": "51106 is a single-direction thrust ball bearing to ISO 104: 30 mm shaft-washer bore, 47 mm outside diameter, 11 mm stack height (1.181 x 1.85 x 0.433 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 20.4 kN, C0a 42 kN and a 1.9 kN fatigue load limit Pu; the grease limiting speed is 4,300 r/min and the oil rating 6,200 r/min; mass about 69 g."
      },
      {
        "q": "How is the 51106 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 06 encodes the 30 mm bore (bore code x 5). The 47 mm OD and 11 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51106 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51106?",
        "a": "At the 4,300 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51106?",
        "a": "The 30/47/11 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 20.4 kN / C0a 42 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51106-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51106"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51206",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51206",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 52,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 29.3,
    "static_load_kN": 58,
    "fatigue_load_limit_kN": 2.63,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "speed_oil_rpm": 4900,
    "weight_g": 139,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 30 x 52 x 16 mm, NTN 51206 sits in the medium-section 51200 thrust family of the single-direction thrust programme. The designation is 512 is the dimension series (medium-section 51200 thrust family) plus 06 encodes the 30 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. The 30/52/16 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "vertical motor and pump thrust shoes",
      "machine-tool tailstock and steady-rest screws",
      "medium crane hook blocks and slewing jibs",
      "extruder and mixer thrust housings"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 30 mm size together from unpacking to assembly.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 30 mm bore.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51206 stack height of 16 mm and washer set differ from the double-direction execution.",
      "Single-direction means exactly that: thrust on 51206 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 29.3/C0a 58 kN ratings and 2.63 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51206; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51206?",
        "a": "51206 is a single-direction thrust ball bearing to ISO 104: 30 mm shaft-washer bore, 52 mm outside diameter, 16 mm stack height (1.181 x 2.047 x 0.63 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 29.3 kN, C0a 58 kN and a 2.63 kN fatigue load limit Pu; the grease limiting speed is 3,400 r/min and the oil rating 4,900 r/min; mass about 139 g."
      },
      {
        "q": "How is the 51206 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 06 encodes the 30 mm bore (bore code x 5). The 52 mm OD and 16 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51206 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51206?",
        "a": "At the 3,400 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51206?",
        "a": "The 30/52/16 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 29.3 kN / C0a 58 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51206-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×52×16 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51206"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51306",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51306",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 60,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 43,
    "static_load_kN": 78.5,
    "fatigue_load_limit_kN": 3.55,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "speed_oil_rpm": 3900,
    "weight_g": 269,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the heavy-section 51300 thrust family, 51306 measures 30 mm through the shaft washer, 60 mm over the outside and 21 mm in assembled height. NTN builds the number from 513 is the dimension series (heavy-section 51300 thrust family); 06 encodes the 30 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 43 kN rating assumes the load arrives truly axial. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "conveyor vertical-drive thrust positions",
      "vertical motor and pump thrust shoes",
      "machine-tool tailstock and steady-rest screws",
      "medium crane hook blocks and slewing jibs"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 30 mm size together from unpacking to assembly.",
      "The 513 heavy section buys capacity with a larger 60 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Single-direction means exactly that: thrust on 51306 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51306 stack height of 21 mm and washer set differ from the double-direction execution.",
      "The Ca 43/C0a 78.5 kN ratings and 3.55 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51306; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51306?",
        "a": "51306 is a single-direction thrust ball bearing to ISO 104: 30 mm shaft-washer bore, 60 mm outside diameter, 21 mm stack height (1.181 x 2.362 x 0.827 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 43 kN, C0a 78.5 kN and a 3.55 kN fatigue load limit Pu; the grease limiting speed is 2,800 r/min and the oil rating 3,900 r/min; mass about 269 g."
      },
      {
        "q": "How is the 51306 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 06 encodes the 30 mm bore (bore code x 5). The 60 mm OD and 21 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51306 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51306?",
        "a": "At the 2,800 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51306?",
        "a": "The 30/60/21 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 43 kN / C0a 78.5 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51306-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×60×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51306"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51406",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51406",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 70,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 72.5,
    "static_load_kN": 126,
    "fatigue_load_limit_kN": 5.65,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "speed_oil_rpm": 3200,
    "weight_g": 516,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51406 appears as a extra-heavy 51400 thrust family bearing with a 30 mm shaft washer, a 70 mm housing diameter and 28 mm of stack height. Reading the code: 514 is the dimension series (extra-heavy 51400 thrust family), and 06 encodes the 30 mm bore (bore code x 5). With Ca 72.5 kN and C0a 126 kN, each mm of shaft bore carries about 2.42 kN of dynamic axial rating. For a 30 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 70 mm OD already tilts the raceway and concentrates the 126 kN static capacity on a few balls. ",
    "applications": [
      "extruder and mixer thrust housings",
      "winch and capstan vertical shafts",
      "press and punch-machine thrust seats",
      "conveyor vertical-drive thrust positions"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 30 mm size together from unpacking to assembly.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Single-direction means exactly that: thrust on 51406 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 72.5 kN never saves a bearing that is running too lightly loaded at 2,200 r/min.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 72.5/C0a 126 kN ratings and 5.65 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51406; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51406?",
        "a": "51406 is a single-direction thrust ball bearing to ISO 104: 30 mm shaft-washer bore, 70 mm outside diameter, 28 mm stack height (1.181 x 2.756 x 1.102 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 72.5 kN, C0a 126 kN and a 5.65 kN fatigue load limit Pu; the grease limiting speed is 2,200 r/min and the oil rating 3,200 r/min; mass about 516 g."
      },
      {
        "q": "How is the 51406 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 06 encodes the 30 mm bore (bore code x 5). The 70 mm OD and 28 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51406 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51406?",
        "a": "At the 2,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51406?",
        "a": "The 30/70/28 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 72.5 kN / C0a 126 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51406-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51406"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51107",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51107",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 52,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 20.4,
    "static_load_kN": 44.5,
    "fatigue_load_limit_kN": 2.02,
    "limiting_speed_rpm": 3900,
    "max_rpm": 3900,
    "speed_oil_rpm": 5600,
    "weight_g": 85,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The light-section 51100 thrust family entry 51107 stacks a shaft washer, ball-and-cage set and housing washer into 12 mm of height over a 35 mm bore. Two fields make up the code — 511 is the dimension series (light-section 51100 thrust family) and 07 encodes the 35 mm bore (bore code x 5). At 12 mm of height the stack is compact for the 35 mm bore class, trading section height for the light-section load level. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 52 mm OD already tilts the raceway and concentrates the 44.5 kN static capacity on a few balls. ",
    "applications": [
      "winch and capstan vertical shafts",
      "press and punch-machine thrust seats",
      "conveyor vertical-drive thrust positions",
      "vertical motor and pump thrust shoes"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 35 mm size together from unpacking to assembly.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 35 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51107 stack height of 12 mm and washer set differ from the double-direction execution.",
      "Shock thrust above C0a 44.5 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 20.4 kN never saves a bearing that is running too lightly loaded at 3,900 r/min.",
      "The Ca 20.4/C0a 44.5 kN ratings and 2.02 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51107; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51107?",
        "a": "51107 is a single-direction thrust ball bearing to ISO 104: 35 mm shaft-washer bore, 52 mm outside diameter, 12 mm stack height (1.378 x 2.047 x 0.472 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 20.4 kN, C0a 44.5 kN and a 2.02 kN fatigue load limit Pu; the grease limiting speed is 3,900 r/min and the oil rating 5,600 r/min; mass about 85 g."
      },
      {
        "q": "How is the 51107 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 07 encodes the 35 mm bore (bore code x 5). The 52 mm OD and 12 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51107 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51107?",
        "a": "At the 3,900 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51107?",
        "a": "The 35/52/12 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 20.4 kN / C0a 44.5 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51107-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×52×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51107"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51207",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51207",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 62,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 39,
    "static_load_kN": 78,
    "fatigue_load_limit_kN": 3.55,
    "limiting_speed_rpm": 2900,
    "max_rpm": 2900,
    "speed_oil_rpm": 4200,
    "weight_g": 215,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51207 is the 35 mm member of NTN's medium-section 51200 thrust family: 62 mm across the washers, 18 mm tall. Reading the code: 512 is the dimension series (medium-section 51200 thrust family), and 07 encodes the 35 mm bore (bore code x 5). On speed, the grease limiting speed is 2,900 r/min and the oil rating 4,200 r/min. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51207 cannot. The shaft washer (bore 35 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "medium crane hook blocks and slewing jibs",
      "extruder and mixer thrust housings",
      "winch and capstan vertical shafts",
      "press and punch-machine thrust seats"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 35 mm size together from unpacking to assembly.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 35 mm bore.",
      "Shock thrust above C0a 78 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Single-direction means exactly that: thrust on 51207 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The Ca 39/C0a 78 kN ratings and 3.55 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51207; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51207?",
        "a": "51207 is a single-direction thrust ball bearing to ISO 104: 35 mm shaft-washer bore, 62 mm outside diameter, 18 mm stack height (1.378 x 2.441 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 39 kN, C0a 78 kN and a 3.55 kN fatigue load limit Pu; the grease limiting speed is 2,900 r/min and the oil rating 4,200 r/min; mass about 215 g."
      },
      {
        "q": "How is the 51207 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 07 encodes the 35 mm bore (bore code x 5). The 62 mm OD and 18 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51207 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51207?",
        "a": "At the 2,900 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51207?",
        "a": "The 35/62/18 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 39 kN / C0a 78 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51207-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×62×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51207"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51307",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51307",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 68,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 55.5,
    "static_load_kN": 105,
    "fatigue_load_limit_kN": 4.75,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "speed_oil_rpm": 3500,
    "weight_g": 383,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51307 is an NTN single-direction thrust ball bearing of the heavy-section 51300 thrust family: 35 mm bore, 68 mm outside diameter, 24 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. The designation is 513 is the dimension series (heavy-section 51300 thrust family) plus 07 encodes the 35 mm bore (bore code x 5). NTN prints 55.5 kN axial dynamic and 105 kN axial static for this size and a 4.75 kN fatigue load limit Pu. Choose the heavy-section 51300 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. The shaft washer (bore 35 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "machine-tool tailstock and steady-rest screws",
      "medium crane hook blocks and slewing jibs",
      "extruder and mixer thrust housings",
      "winch and capstan vertical shafts"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 35 mm size together from unpacking to assembly.",
      "The 513 heavy section buys capacity with a larger 68 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "The 2,400 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51307 has no radial capacity at all.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The Ca 55.5/C0a 105 kN ratings and 4.75 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51307; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51307?",
        "a": "51307 is a single-direction thrust ball bearing to ISO 104: 35 mm shaft-washer bore, 68 mm outside diameter, 24 mm stack height (1.378 x 2.677 x 0.945 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 55.5 kN, C0a 105 kN and a 4.75 kN fatigue load limit Pu; the grease limiting speed is 2,400 r/min and the oil rating 3,500 r/min; mass about 383 g."
      },
      {
        "q": "How is the 51307 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 07 encodes the 35 mm bore (bore code x 5). The 68 mm OD and 24 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51307 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51307?",
        "a": "At the 2,400 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51307?",
        "a": "The 35/68/24 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 55.5 kN / C0a 105 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51307-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×68×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51307"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51407",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51407",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 87,
    "static_load_kN": 155,
    "fatigue_load_limit_kN": 7,
    "limiting_speed_rpm": 1900,
    "max_rpm": 1900,
    "speed_oil_rpm": 2800,
    "weight_g": 759,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51407 belongs to the extra-heavy 51400 thrust family of single-direction thrust ball bearings: 35 / 80 / 32 mm (shaft bore / OD / height). Two fields make up the code — 514 is the dimension series (extra-heavy 51400 thrust family) and 07 encodes the 35 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. Against a thrust roller bearing of the same 35 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "press and punch-machine thrust seats",
      "conveyor vertical-drive thrust positions",
      "vertical motor and pump thrust shoes",
      "machine-tool tailstock and steady-rest screws"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 35 mm size together from unpacking to assembly.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 87 kN never saves a bearing that is running too lightly loaded at 1,900 r/min.",
      "Swapping the shaft and housing washers is an easy assembly error on the 35 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Single-direction means exactly that: thrust on 51407 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 87/C0a 155 kN ratings and 7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51407; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51407?",
        "a": "51407 is a single-direction thrust ball bearing to ISO 104: 35 mm shaft-washer bore, 80 mm outside diameter, 32 mm stack height (1.378 x 3.15 x 1.26 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 87 kN, C0a 155 kN and a 7 kN fatigue load limit Pu; the grease limiting speed is 1,900 r/min and the oil rating 2,800 r/min; mass about 759 g."
      },
      {
        "q": "How is the 51407 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 07 encodes the 35 mm bore (bore code x 5). The 80 mm OD and 32 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51407 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51407?",
        "a": "At the 1,900 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51407?",
        "a": "The 35/80/32 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 87 kN / C0a 155 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51407-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51407"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51108",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51108",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 60,
    "B_mm": 13,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 26.9,
    "static_load_kN": 63,
    "fatigue_load_limit_kN": 2.84,
    "limiting_speed_rpm": 3500,
    "max_rpm": 3500,
    "speed_oil_rpm": 5000,
    "weight_g": 125,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 40 x 60 x 13 mm, NTN 51108 sits in the light-section 51100 thrust family of the single-direction thrust programme. Decoding 51108: 511 is the dimension series (light-section 51100 thrust family), with 08 encodes the 40 mm bore (bore code x 5). The static margin, C0a 63 kN against Ca 26.9 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. Choose the light-section 51100 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "conveyor vertical-drive thrust positions",
      "vertical motor and pump thrust shoes",
      "machine-tool tailstock and steady-rest screws",
      "medium crane hook blocks and slewing jibs"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 40 mm size together from unpacking to assembly.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 40 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51108 has no radial capacity at all.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51108 stack height of 13 mm and washer set differ from the double-direction execution.",
      "Shock thrust above C0a 63 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 26.9/C0a 63 kN ratings and 2.84 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51108; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51108?",
        "a": "51108 is a single-direction thrust ball bearing to ISO 104: 40 mm shaft-washer bore, 60 mm outside diameter, 13 mm stack height (1.575 x 2.362 x 0.512 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 26.9 kN, C0a 63 kN and a 2.84 kN fatigue load limit Pu; the grease limiting speed is 3,500 r/min and the oil rating 5,000 r/min; mass about 125 g."
      },
      {
        "q": "How is the 51108 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 08 encodes the 40 mm bore (bore code x 5). The 60 mm OD and 13 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51108 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51108?",
        "a": "At the 3,500 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51108?",
        "a": "The 40/60/13 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 26.9 kN / C0a 63 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51108-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51108"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51208",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51208",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 68,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 47,
    "static_load_kN": 98.5,
    "fatigue_load_limit_kN": 4.45,
    "limiting_speed_rpm": 2700,
    "max_rpm": 2700,
    "speed_oil_rpm": 3900,
    "weight_g": 276,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the medium-section 51200 thrust family, 51208 measures 40 mm through the shaft washer, 68 mm over the outside and 19 mm in assembled height. Two fields make up the code — 512 is the dimension series (medium-section 51200 thrust family) and 08 encodes the 40 mm bore (bore code x 5). Catalogue axial dynamic rating Ca is 47 kN against C0a 98.5 kN — a static/dynamic ratio of 2.10 that is the signature of a thrust raceway. For a 40 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "winch and capstan vertical shafts",
      "press and punch-machine thrust seats",
      "conveyor vertical-drive thrust positions",
      "vertical motor and pump thrust shoes"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 40 mm size together from unpacking to assembly.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 40 mm bore.",
      "Single-direction means exactly that: thrust on 51208 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51208 has no radial capacity at all.",
      "Swapping the shaft and housing washers is an easy assembly error on the 40 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The Ca 47/C0a 98.5 kN ratings and 4.45 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51208; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51208?",
        "a": "51208 is a single-direction thrust ball bearing to ISO 104: 40 mm shaft-washer bore, 68 mm outside diameter, 19 mm stack height (1.575 x 2.677 x 0.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 47 kN, C0a 98.5 kN and a 4.45 kN fatigue load limit Pu; the grease limiting speed is 2,700 r/min and the oil rating 3,900 r/min; mass about 276 g."
      },
      {
        "q": "How is the 51208 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 08 encodes the 40 mm bore (bore code x 5). The 68 mm OD and 19 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51208 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51208?",
        "a": "At the 2,700 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51208?",
        "a": "The 40/68/19 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 47 kN / C0a 98.5 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51208-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51208"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51308",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51308",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 78,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 69,
    "static_load_kN": 135,
    "fatigue_load_limit_kN": 6.05,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "speed_oil_rpm": 3100,
    "weight_g": 548,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51308 appears as a heavy-section 51300 thrust family bearing with a 40 mm shaft washer, a 78 mm housing diameter and 26 mm of stack height. Reading the code: 513 is the dimension series (heavy-section 51300 thrust family), and 08 encodes the 40 mm bore (bore code x 5). At 26 mm of height the stack is compact for the 40 mm bore class, trading section height for the heavy-section load level. The 40/78/26 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "extruder and mixer thrust housings",
      "winch and capstan vertical shafts",
      "press and punch-machine thrust seats",
      "conveyor vertical-drive thrust positions"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 40 mm size together from unpacking to assembly.",
      "The 513 heavy section buys capacity with a larger 78 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51308 stack height of 26 mm and washer set differ from the double-direction execution.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 69 kN never saves a bearing that is running too lightly loaded at 2,200 r/min.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 69 kN never saves a bearing that is running too lightly loaded at 2,200 r/min.",
      "The Ca 69/C0a 135 kN ratings and 6.05 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51308; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51308?",
        "a": "51308 is a single-direction thrust ball bearing to ISO 104: 40 mm shaft-washer bore, 78 mm outside diameter, 26 mm stack height (1.575 x 3.071 x 1.024 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 69 kN, C0a 135 kN and a 6.05 kN fatigue load limit Pu; the grease limiting speed is 2,200 r/min and the oil rating 3,100 r/min; mass about 548 g."
      },
      {
        "q": "How is the 51308 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 08 encodes the 40 mm bore (bore code x 5). The 78 mm OD and 26 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51308 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51308?",
        "a": "At the 2,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51308?",
        "a": "The 40/78/26 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 69 kN / C0a 135 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51308-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×78×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51308"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51408",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51408",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 112,
    "static_load_kN": 205,
    "fatigue_load_limit_kN": 9.25,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "speed_oil_rpm": 2500,
    "weight_g": 1080,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The extra-heavy 51400 thrust family entry 51408 stacks a shaft washer, ball-and-cage set and housing washer into 36 mm of height over a 40 mm bore. Decoding 51408: 514 is the dimension series (extra-heavy 51400 thrust family), with 08 encodes the 40 mm bore (bore code x 5). On speed, the grease limiting speed is 1,700 r/min and the oil rating 2,500 r/min. If the duty is high speed with light thrust, check the minimum axial load formula first; a too-large thrust ball bearing fails by skid long before its Ca of 112 kN is ever approached. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "vertical motor and pump thrust shoes",
      "machine-tool tailstock and steady-rest screws",
      "medium crane hook blocks and slewing jibs",
      "extruder and mixer thrust housings"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 40 mm size together from unpacking to assembly.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The Ca 112/C0a 205 kN ratings and 9.25 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51408; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51408?",
        "a": "51408 is a single-direction thrust ball bearing to ISO 104: 40 mm shaft-washer bore, 90 mm outside diameter, 36 mm stack height (1.575 x 3.543 x 1.417 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 112 kN, C0a 205 kN and a 9.25 kN fatigue load limit Pu; the grease limiting speed is 1,700 r/min and the oil rating 2,500 r/min; mass about 1080 g."
      },
      {
        "q": "How is the 51408 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 08 encodes the 40 mm bore (bore code x 5). The 90 mm OD and 36 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51408 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51408?",
        "a": "At the 1,700 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51408?",
        "a": "The 40/90/36 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 112 kN / C0a 205 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51408-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51408"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51109",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51109",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 65,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 27.9,
    "static_load_kN": 69,
    "fatigue_load_limit_kN": 3.1,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "speed_oil_rpm": 4600,
    "weight_g": 148,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51109 is the 45 mm member of NTN's light-section 51100 thrust family: 65 mm across the washers, 14 mm tall. NTN builds the number from 511 is the dimension series (light-section 51100 thrust family); 09 encodes the 45 mm bore (bore code x 5). The washer section here is 10.0 mm of radial height, and the catalogue couples it with Ca 27.9 kN / C0a 69 kN. The 45/65/14 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "machine-tool tailstock and steady-rest screws",
      "medium crane hook blocks and slewing jibs",
      "extruder and mixer thrust housings",
      "winch and capstan vertical shafts"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 45 mm size together from unpacking to assembly.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 45 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Swapping the shaft and housing washers is an easy assembly error on the 45 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Single-direction means exactly that: thrust on 51109 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The C0a of 69 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The Ca 27.9/C0a 69 kN ratings and 3.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51109; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51109?",
        "a": "51109 is a single-direction thrust ball bearing to ISO 104: 45 mm shaft-washer bore, 65 mm outside diameter, 14 mm stack height (1.772 x 2.559 x 0.551 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 27.9 kN, C0a 69 kN and a 3.1 kN fatigue load limit Pu; the grease limiting speed is 3,200 r/min and the oil rating 4,600 r/min; mass about 148 g."
      },
      {
        "q": "How is the 51109 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 09 encodes the 45 mm bore (bore code x 5). The 65 mm OD and 14 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51109 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51109?",
        "a": "At the 3,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51109?",
        "a": "The 45/65/14 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 27.9 kN / C0a 69 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51109-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51109"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51209",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51209",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 73,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 47.5,
    "static_load_kN": 105,
    "fatigue_load_limit_kN": 4.75,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "speed_oil_rpm": 3700,
    "weight_g": 317,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51209 is an NTN single-direction thrust ball bearing of the medium-section 51200 thrust family: 45 mm bore, 73 mm outside diameter, 20 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. Decoding 51209: 512 is the dimension series (medium-section 51200 thrust family), with 09 encodes the 45 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 47.5 kN rating assumes the load arrives truly axial. Against a thrust roller bearing of the same 45 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "conveyor vertical-drive thrust positions",
      "vertical motor and pump thrust shoes",
      "machine-tool tailstock and steady-rest screws",
      "medium crane hook blocks and slewing jibs"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 45 mm size together from unpacking to assembly.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 45 mm bore.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 47.5 kN never saves a bearing that is running too lightly loaded at 2,600 r/min.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 47.5 kN never saves a bearing that is running too lightly loaded at 2,600 r/min.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51209 stack height of 20 mm and washer set differ from the double-direction execution.",
      "The Ca 47.5/C0a 105 kN ratings and 4.75 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51209; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51209?",
        "a": "51209 is a single-direction thrust ball bearing to ISO 104: 45 mm shaft-washer bore, 73 mm outside diameter, 20 mm stack height (1.772 x 2.874 x 0.787 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 47.5 kN, C0a 105 kN and a 4.75 kN fatigue load limit Pu; the grease limiting speed is 2,600 r/min and the oil rating 3,700 r/min; mass about 317 g."
      },
      {
        "q": "How is the 51209 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 09 encodes the 45 mm bore (bore code x 5). The 73 mm OD and 20 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51209 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51209?",
        "a": "At the 2,600 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51209?",
        "a": "The 45/73/20 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 47.5 kN / C0a 105 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51209-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×73×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51209"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51309",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51309",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 80,
    "static_load_kN": 163,
    "fatigue_load_limit_kN": 7.35,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "speed_oil_rpm": 2900,
    "weight_g": 684,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51309 belongs to the heavy-section 51300 thrust family of single-direction thrust ball bearings: 45 / 85 / 28 mm (shaft bore / OD / height). Two fields make up the code — 513 is the dimension series (heavy-section 51300 thrust family) and 09 encodes the 45 mm bore (bore code x 5). The static margin, C0a 163 kN against Ca 80 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51309 cannot. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "press and punch-machine thrust seats",
      "conveyor vertical-drive thrust positions",
      "vertical motor and pump thrust shoes",
      "machine-tool tailstock and steady-rest screws"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 45 mm size together from unpacking to assembly.",
      "The 513 heavy section buys capacity with a larger 85 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51309 has no radial capacity at all.",
      "Swapping the shaft and housing washers is an easy assembly error on the 45 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Shock thrust above C0a 163 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 80/C0a 163 kN ratings and 7.35 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51309; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51309?",
        "a": "51309 is a single-direction thrust ball bearing to ISO 104: 45 mm shaft-washer bore, 85 mm outside diameter, 28 mm stack height (1.772 x 3.346 x 1.102 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 80 kN, C0a 163 kN and a 7.35 kN fatigue load limit Pu; the grease limiting speed is 2,000 r/min and the oil rating 2,900 r/min; mass about 684 g."
      },
      {
        "q": "How is the 51309 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 09 encodes the 45 mm bore (bore code x 5). The 85 mm OD and 28 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51309 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51309?",
        "a": "At the 2,000 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51309?",
        "a": "The 45/85/28 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 80 kN / C0a 163 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51309-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51309"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51409",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51409",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 130,
    "static_load_kN": 242,
    "fatigue_load_limit_kN": 10.9,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "speed_oil_rpm": 2200,
    "weight_g": 1430,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 45 x 100 x 39 mm, NTN 51409 sits in the extra-heavy 51400 thrust family of the single-direction thrust programme. NTN builds the number from 514 is the dimension series (extra-heavy 51400 thrust family); 09 encodes the 45 mm bore (bore code x 5). Catalogue axial dynamic rating Ca is 130 kN against C0a 242 kN — a static/dynamic ratio of 1.86 that is the signature of a thrust raceway. Size selection ends with the minimum-load check: at the 1,600 r/min class speed, the balls need a defined axial preload to keep rolling instead of skidding. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "medium crane hook blocks and slewing jibs",
      "extruder and mixer thrust housings",
      "winch and capstan vertical shafts",
      "press and punch-machine thrust seats"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 45 mm size together from unpacking to assembly.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The C0a of 242 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Swapping the shaft and housing washers is an easy assembly error on the 45 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The Ca 130/C0a 242 kN ratings and 10.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51409; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51409?",
        "a": "51409 is a single-direction thrust ball bearing to ISO 104: 45 mm shaft-washer bore, 100 mm outside diameter, 39 mm stack height (1.772 x 3.937 x 1.535 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 130 kN, C0a 242 kN and a 10.9 kN fatigue load limit Pu; the grease limiting speed is 1,600 r/min and the oil rating 2,200 r/min; mass about 1430 g."
      },
      {
        "q": "How is the 51409 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 09 encodes the 45 mm bore (bore code x 5). The 100 mm OD and 39 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51409 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51409?",
        "a": "At the 1,600 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51409?",
        "a": "The 45/100/39 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 130 kN / C0a 242 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51409-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51409"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51110",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51110",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 70,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 28.8,
    "static_load_kN": 75.5,
    "fatigue_load_limit_kN": 3.4,
    "limiting_speed_rpm": 3100,
    "max_rpm": 3100,
    "speed_oil_rpm": 4500,
    "weight_g": 161,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the light-section 51100 thrust family, 51110 measures 50 mm through the shaft washer, 70 mm over the outside and 14 mm in assembled height. Two fields make up the code — 511 is the dimension series (light-section 51100 thrust family) and 10 encodes the 50 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. If the duty is high speed with light thrust, check the minimum axial load formula first; a too-large thrust ball bearing fails by skid long before its Ca of 28.8 kN is ever approached. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "press and punch-machine thrust seats",
      "conveyor vertical-drive thrust positions",
      "vertical motor and pump thrust shoes",
      "machine-tool tailstock and steady-rest screws"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 50 mm size together from unpacking to assembly.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 50 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51110 has no radial capacity at all.",
      "Single-direction means exactly that: thrust on 51110 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 28.8/C0a 75.5 kN ratings and 3.4 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51110; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51110?",
        "a": "51110 is a single-direction thrust ball bearing to ISO 104: 50 mm shaft-washer bore, 70 mm outside diameter, 14 mm stack height (1.969 x 2.756 x 0.551 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 28.8 kN, C0a 75.5 kN and a 3.4 kN fatigue load limit Pu; the grease limiting speed is 3,100 r/min and the oil rating 4,500 r/min; mass about 161 g."
      },
      {
        "q": "How is the 51110 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 10 encodes the 50 mm bore (bore code x 5). The 70 mm OD and 14 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51110 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51110?",
        "a": "At the 3,100 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51110?",
        "a": "The 50/70/14 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 28.8 kN / C0a 75.5 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51110-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51110"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51210",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51210",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 78,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 48.5,
    "static_load_kN": 111,
    "fatigue_load_limit_kN": 5.05,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "speed_oil_rpm": 3400,
    "weight_g": 378,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51210 appears as a medium-section 51200 thrust family bearing with a 50 mm shaft washer, a 78 mm housing diameter and 22 mm of stack height. Reading the code: 512 is the dimension series (medium-section 51200 thrust family), and 10 encodes the 50 mm bore (bore code x 5). The washer section here is 14.0 mm of radial height, and the catalogue couples it with Ca 48.5 kN / C0a 111 kN. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "extruder and mixer thrust housings",
      "winch and capstan vertical shafts",
      "press and punch-machine thrust seats",
      "conveyor vertical-drive thrust positions"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 50 mm size together from unpacking to assembly.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 50 mm bore.",
      "Swapping the shaft and housing washers is an easy assembly error on the 50 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Swapping the shaft and housing washers is an easy assembly error on the 50 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The C0a of 111 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The Ca 48.5/C0a 111 kN ratings and 5.05 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51210; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51210?",
        "a": "51210 is a single-direction thrust ball bearing to ISO 104: 50 mm shaft-washer bore, 78 mm outside diameter, 22 mm stack height (1.969 x 3.071 x 0.866 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 48.5 kN, C0a 111 kN and a 5.05 kN fatigue load limit Pu; the grease limiting speed is 2,400 r/min and the oil rating 3,400 r/min; mass about 378 g."
      },
      {
        "q": "How is the 51210 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 10 encodes the 50 mm bore (bore code x 5). The 78 mm OD and 22 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51210 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51210?",
        "a": "At the 2,400 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51210?",
        "a": "The 50/78/22 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 48.5 kN / C0a 111 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51210-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51210"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51310",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51310",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 95,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 96.5,
    "static_load_kN": 202,
    "fatigue_load_limit_kN": 9.1,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "speed_oil_rpm": 2600,
    "weight_g": 951,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The heavy-section 51300 thrust family entry 51310 stacks a shaft washer, ball-and-cage set and housing washer into 31 mm of height over a 50 mm bore. The designation is 513 is the dimension series (heavy-section 51300 thrust family) plus 10 encodes the 50 mm bore (bore code x 5). With Ca 96.5 kN and C0a 202 kN, each mm of shaft bore carries about 1.93 kN of dynamic axial rating. Size selection ends with the minimum-load check: at the 1,800 r/min class speed, the balls need a defined axial preload to keep rolling instead of skidding. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "medium crane hook blocks and slewing jibs",
      "extruder and mixer thrust housings",
      "winch and capstan vertical shafts",
      "press and punch-machine thrust seats"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 50 mm size together from unpacking to assembly.",
      "The 513 heavy section buys capacity with a larger 95 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 96.5 kN never saves a bearing that is running too lightly loaded at 1,800 r/min.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 96.5/C0a 202 kN ratings and 9.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51310; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51310?",
        "a": "51310 is a single-direction thrust ball bearing to ISO 104: 50 mm shaft-washer bore, 95 mm outside diameter, 31 mm stack height (1.969 x 3.74 x 1.22 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 96.5 kN, C0a 202 kN and a 9.1 kN fatigue load limit Pu; the grease limiting speed is 1,800 r/min and the oil rating 2,600 r/min; mass about 951 g."
      },
      {
        "q": "How is the 51310 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 10 encodes the 50 mm bore (bore code x 5). The 95 mm OD and 31 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51310 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51310?",
        "a": "At the 1,800 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51310?",
        "a": "The 50/95/31 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 96.5 kN / C0a 202 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51310-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×95×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51310"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51410A",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51410A",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 148,
    "static_load_kN": 283,
    "fatigue_load_limit_kN": 12.8,
    "limiting_speed_rpm": 1400,
    "max_rpm": 1400,
    "speed_oil_rpm": 2000,
    "weight_g": 1900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51410A is an NTN single-direction thrust ball bearing of the extra-heavy 51400 thrust family: 50 mm bore, 110 mm outside diameter, 43 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. The designation is 514 is the dimension series (extra-heavy 51400 thrust family) plus 10 encodes the 50 mm bore (bore code x 5); the trailing A marks an internal-design revision of this dimension. With Ca 148 kN and C0a 283 kN, each mm of shaft bore carries about 2.96 kN of dynamic axial rating. Against a thrust roller bearing of the same 50 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "vertical motor and pump thrust shoes",
      "machine-tool tailstock and steady-rest screws",
      "medium crane hook blocks and slewing jibs",
      "extruder and mixer thrust housings"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 50 mm size together from unpacking to assembly.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "The C0a of 283 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Single-direction means exactly that: thrust on 51410A in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 148/C0a 283 kN ratings and 12.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51410A; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51410A?",
        "a": "51410A is a single-direction thrust ball bearing to ISO 104: 50 mm shaft-washer bore, 110 mm outside diameter, 43 mm stack height (1.969 x 4.331 x 1.693 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 148 kN, C0a 283 kN and a 12.8 kN fatigue load limit Pu; the grease limiting speed is 1,400 r/min and the oil rating 2,000 r/min; mass about 1900 g."
      },
      {
        "q": "How is the 51410A designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 10 encodes the 50 mm bore (bore code x 5); the trailing A marks an internal-design revision of this dimension. The 110 mm OD and 43 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51410A carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51410A?",
        "a": "At the 1,400 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51410A?",
        "a": "The 50/110/43 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 148 kN / C0a 283 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51410A",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51410a",
      "51410A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51111",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51111",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 78,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 35,
    "static_load_kN": 93,
    "fatigue_load_limit_kN": 4.2,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "speed_oil_rpm": 4000,
    "weight_g": 226,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51111 is an NTN single-direction thrust ball bearing of the light-section 51100 thrust family: 55 mm bore, 78 mm outside diameter, 16 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. Decoding 51111: 511 is the dimension series (light-section 51100 thrust family), with 11 encodes the 55 mm bore (bore code x 5). On speed, the grease limiting speed is 2,800 r/min and the oil rating 4,000 r/min. Size selection ends with the minimum-load check: at the 2,800 r/min class speed, the balls need a defined axial preload to keep rolling instead of skidding. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 78 mm OD already tilts the raceway and concentrates the 93 kN static capacity on a few balls. ",
    "applications": [
      "vertical motor and pump thrust shoes",
      "machine-tool tailstock and steady-rest screws",
      "medium crane hook blocks and slewing jibs",
      "extruder and mixer thrust housings"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 55 mm size together from unpacking to assembly.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 55 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 35 kN never saves a bearing that is running too lightly loaded at 2,800 r/min.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The Ca 35/C0a 93 kN ratings and 4.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51111; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51111?",
        "a": "51111 is a single-direction thrust ball bearing to ISO 104: 55 mm shaft-washer bore, 78 mm outside diameter, 16 mm stack height (2.165 x 3.071 x 0.63 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 35 kN, C0a 93 kN and a 4.2 kN fatigue load limit Pu; the grease limiting speed is 2,800 r/min and the oil rating 4,000 r/min; mass about 226 g."
      },
      {
        "q": "How is the 51111 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 11 encodes the 55 mm bore (bore code x 5). The 78 mm OD and 16 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51111 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51111?",
        "a": "At the 2,800 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51111?",
        "a": "The 55/78/16 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 35 kN / C0a 93 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51111-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×78×16 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51111"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51211",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51211",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 90,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 69.5,
    "static_load_kN": 159,
    "fatigue_load_limit_kN": 7.15,
    "limiting_speed_rpm": 2100,
    "max_rpm": 2100,
    "speed_oil_rpm": 3000,
    "weight_g": 608,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51211 belongs to the medium-section 51200 thrust family of single-direction thrust ball bearings: 55 / 90 / 25 mm (shaft bore / OD / height). Two fields make up the code — 512 is the dimension series (medium-section 51200 thrust family) and 11 encodes the 55 mm bore (bore code x 5). The ball-and-cage set is separable from both washers, which is why the mounting order (shaft washer first, then cage, then housing washer) matters. Choose the medium-section 51200 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. The shaft washer (bore 55 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "press and punch-machine thrust seats",
      "conveyor vertical-drive thrust positions",
      "vertical motor and pump thrust shoes",
      "machine-tool tailstock and steady-rest screws"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 55 mm size together from unpacking to assembly.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 55 mm bore.",
      "The C0a of 159 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51211 has no radial capacity at all.",
      "The Ca 69.5/C0a 159 kN ratings and 7.15 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51211; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51211?",
        "a": "51211 is a single-direction thrust ball bearing to ISO 104: 55 mm shaft-washer bore, 90 mm outside diameter, 25 mm stack height (2.165 x 3.543 x 0.984 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 69.5 kN, C0a 159 kN and a 7.15 kN fatigue load limit Pu; the grease limiting speed is 2,100 r/min and the oil rating 3,000 r/min; mass about 608 g."
      },
      {
        "q": "How is the 51211 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 11 encodes the 55 mm bore (bore code x 5). The 90 mm OD and 25 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51211 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51211?",
        "a": "At the 2,100 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51211?",
        "a": "The 55/90/25 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 69.5 kN / C0a 159 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51211-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×90×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51211"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51311",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51311",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 105,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 119,
    "static_load_kN": 246,
    "fatigue_load_limit_kN": 11.1,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "speed_oil_rpm": 2300,
    "weight_g": 1290,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 55 x 105 x 35 mm, NTN 51311 sits in the heavy-section 51300 thrust family of the single-direction thrust programme. Reading the code: 513 is the dimension series (heavy-section 51300 thrust family), and 11 encodes the 55 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 246 kN class figures at the cost of OD and height. The shaft washer (bore 55 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "winch and capstan vertical shafts",
      "press and punch-machine thrust seats",
      "conveyor vertical-drive thrust positions",
      "vertical motor and pump thrust shoes"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 55 mm size together from unpacking to assembly.",
      "The 513 heavy section buys capacity with a larger 105 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The C0a of 246 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Single-direction means exactly that: thrust on 51311 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 119/C0a 246 kN ratings and 11.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51311; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51311?",
        "a": "51311 is a single-direction thrust ball bearing to ISO 104: 55 mm shaft-washer bore, 105 mm outside diameter, 35 mm stack height (2.165 x 4.134 x 1.378 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 119 kN, C0a 246 kN and a 11.1 kN fatigue load limit Pu; the grease limiting speed is 1,600 r/min and the oil rating 2,300 r/min; mass about 1290 g."
      },
      {
        "q": "How is the 51311 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 11 encodes the 55 mm bore (bore code x 5). The 105 mm OD and 35 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51311 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51311?",
        "a": "At the 1,600 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51311?",
        "a": "The 55/105/35 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 119 kN / C0a 246 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51311-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×105×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51311"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51411",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51411",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 48,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 178,
    "static_load_kN": 360,
    "fatigue_load_limit_kN": 16.2,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "speed_oil_rpm": 1800,
    "weight_g": 2520,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the extra-heavy 51400 thrust family, 51411 measures 55 mm through the shaft washer, 120 mm over the outside and 48 mm in assembled height. Decoding 51411: 514 is the dimension series (extra-heavy 51400 thrust family), with 11 encodes the 55 mm bore (bore code x 5). The washer section here is 32.5 mm of radial height, and the catalogue couples it with Ca 178 kN / C0a 360 kN. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51411 cannot. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "machine-tool tailstock and steady-rest screws",
      "medium crane hook blocks and slewing jibs",
      "extruder and mixer thrust housings",
      "winch and capstan vertical shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "In this size class the frequent miss is washer identification: keep the catalogued shaft/housing washer pairing of the 55 mm size together from unpacking to assembly.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Shock thrust above C0a 360 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The C0a of 360 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The Ca 178/C0a 360 kN ratings and 16.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51411; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51411?",
        "a": "51411 is a single-direction thrust ball bearing to ISO 104: 55 mm shaft-washer bore, 120 mm outside diameter, 48 mm stack height (2.165 x 4.724 x 1.89 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 178 kN, C0a 360 kN and a 16.2 kN fatigue load limit Pu; the grease limiting speed is 1,300 r/min and the oil rating 1,800 r/min; mass about 2520 g."
      },
      {
        "q": "How is the 51411 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 11 encodes the 55 mm bore (bore code x 5). The 120 mm OD and 48 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51411 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51411?",
        "a": "At the 1,300 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51411?",
        "a": "The 55/120/48 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 178 kN / C0a 360 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51411-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51411"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51112",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51112",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 85,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 41.5,
    "static_load_kN": 113,
    "fatigue_load_limit_kN": 5.1,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "speed_oil_rpm": 3700,
    "weight_g": 296,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51112 appears as a light-section 51100 thrust family bearing with a 60 mm shaft washer, a 85 mm housing diameter and 17 mm of stack height. NTN builds the number from 511 is the dimension series (light-section 51100 thrust family); 12 encodes the 60 mm bore (bore code x 5). Catalogue axial dynamic rating Ca is 41.5 kN against C0a 113 kN — a static/dynamic ratio of 2.72 that is the signature of a thrust raceway. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 113 kN class figures at the cost of OD and height. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "At 60 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 60 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "The 2,600 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "Swapping the shaft and housing washers is an easy assembly error on the 60 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Swapping the shaft and housing washers is an easy assembly error on the 60 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The Ca 41.5/C0a 113 kN ratings and 5.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51112; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51112?",
        "a": "51112 is a single-direction thrust ball bearing to ISO 104: 60 mm shaft-washer bore, 85 mm outside diameter, 17 mm stack height (2.362 x 3.346 x 0.669 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 41.5 kN, C0a 113 kN and a 5.1 kN fatigue load limit Pu; the grease limiting speed is 2,600 r/min and the oil rating 3,700 r/min; mass about 296 g."
      },
      {
        "q": "How is the 51112 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 12 encodes the 60 mm bore (bore code x 5). The 85 mm OD and 17 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51112 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51112?",
        "a": "At the 2,600 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51112?",
        "a": "The 60/85/17 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 41.5 kN / C0a 113 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51112-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51112"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51212",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51212",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 95,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 73.5,
    "static_load_kN": 179,
    "fatigue_load_limit_kN": 8.05,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "speed_oil_rpm": 2800,
    "weight_g": 676,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The medium-section 51200 thrust family entry 51212 stacks a shaft washer, ball-and-cage set and housing washer into 26 mm of height over a 60 mm bore. Decoding 51212: 512 is the dimension series (medium-section 51200 thrust family), with 12 encodes the 60 mm bore (bore code x 5). Catalogue mass is about 676 g for the full washer-and-cage stack. The 60/95/26 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "At 60 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 60 mm bore.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The C0a of 179 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The 2,000 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The Ca 73.5/C0a 179 kN ratings and 8.05 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51212; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51212?",
        "a": "51212 is a single-direction thrust ball bearing to ISO 104: 60 mm shaft-washer bore, 95 mm outside diameter, 26 mm stack height (2.362 x 3.74 x 1.024 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 73.5 kN, C0a 179 kN and a 8.05 kN fatigue load limit Pu; the grease limiting speed is 2,000 r/min and the oil rating 2,800 r/min; mass about 676 g."
      },
      {
        "q": "How is the 51212 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 12 encodes the 60 mm bore (bore code x 5). The 95 mm OD and 26 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51212 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51212?",
        "a": "At the 2,000 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51212?",
        "a": "The 60/95/26 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 73.5 kN / C0a 179 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51212-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×95×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51212"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51312",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51312",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 123,
    "static_load_kN": 267,
    "fatigue_load_limit_kN": 12,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "speed_oil_rpm": 2300,
    "weight_g": 1370,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51312 is the 60 mm member of NTN's heavy-section 51300 thrust family: 110 mm across the washers, 35 mm tall. Two fields make up the code — 513 is the dimension series (heavy-section 51300 thrust family) and 12 encodes the 60 mm bore (bore code x 5). On speed, the grease limiting speed is 1,600 r/min and the oil rating 2,300 r/min. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "At 60 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 513 heavy section buys capacity with a larger 110 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The Ca 123/C0a 267 kN ratings and 12 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51312; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51312?",
        "a": "51312 is a single-direction thrust ball bearing to ISO 104: 60 mm shaft-washer bore, 110 mm outside diameter, 35 mm stack height (2.362 x 4.331 x 1.378 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 123 kN, C0a 267 kN and a 12 kN fatigue load limit Pu; the grease limiting speed is 1,600 r/min and the oil rating 2,300 r/min; mass about 1370 g."
      },
      {
        "q": "How is the 51312 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 12 encodes the 60 mm bore (bore code x 5). The 110 mm OD and 35 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51312 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51312?",
        "a": "At the 1,600 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51312?",
        "a": "The 60/110/35 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 123 kN / C0a 267 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51312-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51312"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51412",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51412",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 51,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 214,
    "static_load_kN": 435,
    "fatigue_load_limit_kN": 19.7,
    "limiting_speed_rpm": 1200,
    "max_rpm": 1200,
    "speed_oil_rpm": 1700,
    "weight_g": 3120,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51412 is an NTN single-direction thrust ball bearing of the extra-heavy 51400 thrust family: 60 mm bore, 130 mm outside diameter, 51 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. NTN builds the number from 514 is the dimension series (extra-heavy 51400 thrust family); 12 encodes the 60 mm bore (bore code x 5). The ball-and-cage set is separable from both washers, which is why the mounting order (shaft washer first, then cage, then housing washer) matters. For a 60 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "At 60 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Single-direction means exactly that: thrust on 51412 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The 1,200 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51412 has no radial capacity at all.",
      "The Ca 214/C0a 435 kN ratings and 19.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51412; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51412?",
        "a": "51412 is a single-direction thrust ball bearing to ISO 104: 60 mm shaft-washer bore, 130 mm outside diameter, 51 mm stack height (2.362 x 5.118 x 2.008 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 214 kN, C0a 435 kN and a 19.7 kN fatigue load limit Pu; the grease limiting speed is 1,200 r/min and the oil rating 1,700 r/min; mass about 3120 g."
      },
      {
        "q": "How is the 51412 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 12 encodes the 60 mm bore (bore code x 5). The 130 mm OD and 51 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51412 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51412?",
        "a": "At the 1,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51412?",
        "a": "The 60/130/51 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 214 kN / C0a 435 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51412-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51412"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51113",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51113",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 90,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 41.5,
    "static_load_kN": 117,
    "fatigue_load_limit_kN": 5.3,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "speed_oil_rpm": 3500,
    "weight_g": 338,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51113 belongs to the light-section 51100 thrust family of single-direction thrust ball bearings: 65 / 90 / 18 mm (shaft bore / OD / height). The designation is 511 is the dimension series (light-section 51100 thrust family) plus 13 encodes the 65 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 41.5 kN rating assumes the load arrives truly axial. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "At 65 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 65 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51113 stack height of 18 mm and washer set differ from the double-direction execution.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51113 stack height of 18 mm and washer set differ from the double-direction execution.",
      "The Ca 41.5/C0a 117 kN ratings and 5.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51113; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51113?",
        "a": "51113 is a single-direction thrust ball bearing to ISO 104: 65 mm shaft-washer bore, 90 mm outside diameter, 18 mm stack height (2.559 x 3.543 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 41.5 kN, C0a 117 kN and a 5.3 kN fatigue load limit Pu; the grease limiting speed is 2,400 r/min and the oil rating 3,500 r/min; mass about 338 g."
      },
      {
        "q": "How is the 51113 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 13 encodes the 65 mm bore (bore code x 5). The 90 mm OD and 18 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51113 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51113?",
        "a": "At the 2,400 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51113?",
        "a": "The 65/90/18 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 41.5 kN / C0a 117 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51113-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×90×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51113"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51213",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51213",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 100,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 75,
    "static_load_kN": 189,
    "fatigue_load_limit_kN": 8.5,
    "limiting_speed_rpm": 1900,
    "max_rpm": 1900,
    "speed_oil_rpm": 2700,
    "weight_g": 767,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 65 x 100 x 27 mm, NTN 51213 sits in the medium-section 51200 thrust family of the single-direction thrust programme. NTN builds the number from 512 is the dimension series (medium-section 51200 thrust family); 13 encodes the 65 mm bore (bore code x 5). With Ca 75 kN and C0a 189 kN, each mm of shaft bore carries about 1.15 kN of dynamic axial rating. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51213 cannot. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "At 65 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 65 mm bore.",
      "Shock thrust above C0a 189 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 75/C0a 189 kN ratings and 8.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51213; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51213?",
        "a": "51213 is a single-direction thrust ball bearing to ISO 104: 65 mm shaft-washer bore, 100 mm outside diameter, 27 mm stack height (2.559 x 3.937 x 1.063 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 75 kN, C0a 189 kN and a 8.5 kN fatigue load limit Pu; the grease limiting speed is 1,900 r/min and the oil rating 2,700 r/min; mass about 767 g."
      },
      {
        "q": "How is the 51213 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 13 encodes the 65 mm bore (bore code x 5). The 100 mm OD and 27 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51213 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51213?",
        "a": "At the 1,900 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51213?",
        "a": "The 65/100/27 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 75 kN / C0a 189 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51213-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×100×27 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51213"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51313",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51313",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 115,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 128,
    "static_load_kN": 287,
    "fatigue_load_limit_kN": 13,
    "limiting_speed_rpm": 1500,
    "max_rpm": 1500,
    "speed_oil_rpm": 2200,
    "weight_g": 1510,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the heavy-section 51300 thrust family, 51313 measures 65 mm through the shaft washer, 115 mm over the outside and 36 mm in assembled height. Decoding 51313: 513 is the dimension series (heavy-section 51300 thrust family), with 13 encodes the 65 mm bore (bore code x 5). Catalogue axial dynamic rating Ca is 128 kN against C0a 287 kN — a static/dynamic ratio of 2.24 that is the signature of a thrust raceway. Choose the heavy-section 51300 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "At 65 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 513 heavy section buys capacity with a larger 115 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "The 1,500 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Swapping the shaft and housing washers is an easy assembly error on the 65 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The Ca 128/C0a 287 kN ratings and 13 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51313; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51313?",
        "a": "51313 is a single-direction thrust ball bearing to ISO 104: 65 mm shaft-washer bore, 115 mm outside diameter, 36 mm stack height (2.559 x 4.528 x 1.417 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 128 kN, C0a 287 kN and a 13 kN fatigue load limit Pu; the grease limiting speed is 1,500 r/min and the oil rating 2,200 r/min; mass about 1510 g."
      },
      {
        "q": "How is the 51313 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 13 encodes the 65 mm bore (bore code x 5). The 115 mm OD and 36 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51313 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51313?",
        "a": "At the 1,500 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51313?",
        "a": "The 65/115/36 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 128 kN / C0a 287 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51313-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×115×36 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51313"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51413",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51413",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 56,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 232,
    "static_load_kN": 495,
    "fatigue_load_limit_kN": 22,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "speed_oil_rpm": 1600,
    "weight_g": 3960,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51413 appears as a extra-heavy 51400 thrust family bearing with a 65 mm shaft washer, a 140 mm housing diameter and 56 mm of stack height. The designation is 514 is the dimension series (extra-heavy 51400 thrust family) plus 13 encodes the 65 mm bore (bore code x 5). Catalogue mass is about 3960 g for the full washer-and-cage stack. Against a thrust roller bearing of the same 65 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "At 65 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 232 kN never saves a bearing that is running too lightly loaded at 1,100 r/min.",
      "Shock thrust above C0a 495 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The 1,100 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The Ca 232/C0a 495 kN ratings and 22 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51413; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51413?",
        "a": "51413 is a single-direction thrust ball bearing to ISO 104: 65 mm shaft-washer bore, 140 mm outside diameter, 56 mm stack height (2.559 x 5.512 x 2.205 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 232 kN, C0a 495 kN and a 22 kN fatigue load limit Pu; the grease limiting speed is 1,100 r/min and the oil rating 1,600 r/min; mass about 3960 g."
      },
      {
        "q": "How is the 51413 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 13 encodes the 65 mm bore (bore code x 5). The 140 mm OD and 56 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51413 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51413?",
        "a": "At the 1,100 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51413?",
        "a": "The 65/140/56 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 232 kN / C0a 495 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51413-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51413"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51114",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51114",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 95,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 43,
    "static_load_kN": 127,
    "fatigue_load_limit_kN": 5.7,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "speed_oil_rpm": 3400,
    "weight_g": 356,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The light-section 51100 thrust family entry 51114 stacks a shaft washer, ball-and-cage set and housing washer into 18 mm of height over a 70 mm bore. Reading the code: 511 is the dimension series (light-section 51100 thrust family), and 14 encodes the 70 mm bore (bore code x 5). NTN prints 43 kN axial dynamic and 127 kN axial static for this size and a 5.7 kN fatigue load limit Pu. Choose the light-section 51100 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "At 70 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 70 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51114 has no radial capacity at all.",
      "The C0a of 127 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The Ca 43/C0a 127 kN ratings and 5.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51114; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51114?",
        "a": "51114 is a single-direction thrust ball bearing to ISO 104: 70 mm shaft-washer bore, 95 mm outside diameter, 18 mm stack height (2.756 x 3.74 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 43 kN, C0a 127 kN and a 5.7 kN fatigue load limit Pu; the grease limiting speed is 2,400 r/min and the oil rating 3,400 r/min; mass about 356 g."
      },
      {
        "q": "How is the 51114 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 14 encodes the 70 mm bore (bore code x 5). The 95 mm OD and 18 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51114 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51114?",
        "a": "At the 2,400 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51114?",
        "a": "The 70/95/18 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 43 kN / C0a 127 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51114-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51114"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51214",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51214",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 105,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 76,
    "static_load_kN": 199,
    "fatigue_load_limit_kN": 8.95,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "speed_oil_rpm": 2600,
    "weight_g": 793,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51214 is the 70 mm member of NTN's medium-section 51200 thrust family: 105 mm across the washers, 27 mm tall. The designation is 512 is the dimension series (medium-section 51200 thrust family) plus 14 encodes the 70 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. For a 70 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 105 mm OD already tilts the raceway and concentrates the 199 kN static capacity on a few balls. ",
    "applications": [
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "At 70 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 70 mm bore.",
      "Single-direction means exactly that: thrust on 51214 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Single-direction means exactly that: thrust on 51214 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 76/C0a 199 kN ratings and 8.95 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51214; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51214?",
        "a": "51214 is a single-direction thrust ball bearing to ISO 104: 70 mm shaft-washer bore, 105 mm outside diameter, 27 mm stack height (2.756 x 4.134 x 1.063 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 76 kN, C0a 199 kN and a 8.95 kN fatigue load limit Pu; the grease limiting speed is 1,800 r/min and the oil rating 2,600 r/min; mass about 793 g."
      },
      {
        "q": "How is the 51214 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 14 encodes the 70 mm bore (bore code x 5). The 105 mm OD and 27 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51214 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51214?",
        "a": "At the 1,800 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51214?",
        "a": "The 70/105/27 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 76 kN / C0a 199 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51214-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×105×27 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51214"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51314",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51314",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 148,
    "static_load_kN": 340,
    "fatigue_load_limit_kN": 15.3,
    "limiting_speed_rpm": 1400,
    "max_rpm": 1400,
    "speed_oil_rpm": 2000,
    "weight_g": 2010,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51314 is an NTN single-direction thrust ball bearing of the heavy-section 51300 thrust family: 70 mm bore, 125 mm outside diameter, 40 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. NTN builds the number from 513 is the dimension series (heavy-section 51300 thrust family); 14 encodes the 70 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 148 kN rating assumes the load arrives truly axial. The 70/125/40 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 125 mm OD already tilts the raceway and concentrates the 340 kN static capacity on a few balls. ",
    "applications": [
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "At 70 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 513 heavy section buys capacity with a larger 125 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51314 stack height of 40 mm and washer set differ from the double-direction execution.",
      "The 1,400 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51314 stack height of 40 mm and washer set differ from the double-direction execution.",
      "The Ca 148/C0a 340 kN ratings and 15.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51314; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51314?",
        "a": "51314 is a single-direction thrust ball bearing to ISO 104: 70 mm shaft-washer bore, 125 mm outside diameter, 40 mm stack height (2.756 x 4.921 x 1.575 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 148 kN, C0a 340 kN and a 15.3 kN fatigue load limit Pu; the grease limiting speed is 1,400 r/min and the oil rating 2,000 r/min; mass about 2010 g."
      },
      {
        "q": "How is the 51314 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 14 encodes the 70 mm bore (bore code x 5). The 125 mm OD and 40 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51314 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51314?",
        "a": "At the 1,400 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51314?",
        "a": "The 70/125/40 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 148 kN / C0a 340 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51314-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51314"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51414",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51414",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 60,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 250,
    "static_load_kN": 555,
    "fatigue_load_limit_kN": 23.8,
    "limiting_speed_rpm": 1000,
    "max_rpm": 1000,
    "speed_oil_rpm": 1500,
    "weight_g": 4860,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51414 belongs to the extra-heavy 51400 thrust family of single-direction thrust ball bearings: 70 / 150 / 60 mm (shaft bore / OD / height). Reading the code: 514 is the dimension series (extra-heavy 51400 thrust family), and 14 encodes the 70 mm bore (bore code x 5). With Ca 250 kN and C0a 555 kN, each mm of shaft bore carries about 3.57 kN of dynamic axial rating. If the duty is high speed with light thrust, check the minimum axial load formula first; a too-large thrust ball bearing fails by skid long before its Ca of 250 kN is ever approached. The shaft washer (bore 70 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "At 70 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51414 stack height of 60 mm and washer set differ from the double-direction execution.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 250/C0a 555 kN ratings and 23.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51414; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51414?",
        "a": "51414 is a single-direction thrust ball bearing to ISO 104: 70 mm shaft-washer bore, 150 mm outside diameter, 60 mm stack height (2.756 x 5.906 x 2.362 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 250 kN, C0a 555 kN and a 23.8 kN fatigue load limit Pu; the grease limiting speed is 1,000 r/min and the oil rating 1,500 r/min; mass about 4860 g."
      },
      {
        "q": "How is the 51414 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 14 encodes the 70 mm bore (bore code x 5). The 150 mm OD and 60 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51414 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51414?",
        "a": "At the 1,000 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51414?",
        "a": "The 70/150/60 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 250 kN / C0a 555 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51414-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51414"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51115",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51115",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 75,
    "D_mm": 100,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 44.5,
    "static_load_kN": 136,
    "fatigue_load_limit_kN": 6.15,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "speed_oil_rpm": 3200,
    "weight_g": 399,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 75 x 100 x 19 mm, NTN 51115 sits in the light-section 51100 thrust family of the single-direction thrust programme. Two fields make up the code — 511 is the dimension series (light-section 51100 thrust family) and 15 encodes the 75 mm bore (bore code x 5). At 19 mm of height the stack is compact for the 75 mm bore class, trading section height for the light-section load level. The 75/100/19 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. The shaft washer (bore 75 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "At 75 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 75 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Swapping the shaft and housing washers is an easy assembly error on the 75 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 44.5 kN never saves a bearing that is running too lightly loaded at 2,200 r/min.",
      "The Ca 44.5/C0a 136 kN ratings and 6.15 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51115; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51115?",
        "a": "51115 is a single-direction thrust ball bearing to ISO 104: 75 mm shaft-washer bore, 100 mm outside diameter, 19 mm stack height (2.953 x 3.937 x 0.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 44.5 kN, C0a 136 kN and a 6.15 kN fatigue load limit Pu; the grease limiting speed is 2,200 r/min and the oil rating 3,200 r/min; mass about 399 g."
      },
      {
        "q": "How is the 51115 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 15 encodes the 75 mm bore (bore code x 5). The 100 mm OD and 19 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51115 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51115?",
        "a": "At the 2,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51115?",
        "a": "The 75/100/19 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 44.5 kN / C0a 136 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51115-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51115"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51215",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51215",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 75,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 77.5,
    "static_load_kN": 209,
    "fatigue_load_limit_kN": 9.4,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "speed_oil_rpm": 2600,
    "weight_g": 874,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the medium-section 51200 thrust family, 51215 measures 75 mm through the shaft washer, 110 mm over the outside and 27 mm in assembled height. Reading the code: 512 is the dimension series (medium-section 51200 thrust family), and 15 encodes the 75 mm bore (bore code x 5). On speed, the grease limiting speed is 1,800 r/min and the oil rating 2,600 r/min. Against a thrust roller bearing of the same 75 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "At 75 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 75 mm bore.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 77.5 kN never saves a bearing that is running too lightly loaded at 1,800 r/min.",
      "The 1,800 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The Ca 77.5/C0a 209 kN ratings and 9.4 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51215; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51215?",
        "a": "51215 is a single-direction thrust ball bearing to ISO 104: 75 mm shaft-washer bore, 110 mm outside diameter, 27 mm stack height (2.953 x 4.331 x 1.063 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 77.5 kN, C0a 209 kN and a 9.4 kN fatigue load limit Pu; the grease limiting speed is 1,800 r/min and the oil rating 2,600 r/min; mass about 874 g."
      },
      {
        "q": "How is the 51215 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 15 encodes the 75 mm bore (bore code x 5). The 110 mm OD and 27 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51215 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51215?",
        "a": "At the 1,800 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51215?",
        "a": "The 75/110/27 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 77.5 kN / C0a 209 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51215-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×110×27 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51215"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51315",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51315",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 75,
    "D_mm": 135,
    "B_mm": 44,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 171,
    "static_load_kN": 395,
    "fatigue_load_limit_kN": 17.4,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "speed_oil_rpm": 1800,
    "weight_g": 2610,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51315 appears as a heavy-section 51300 thrust family bearing with a 75 mm shaft washer, a 135 mm housing diameter and 44 mm of stack height. The designation is 513 is the dimension series (heavy-section 51300 thrust family) plus 15 encodes the 75 mm bore (bore code x 5). NTN prints 171 kN axial dynamic and 395 kN axial static for this size and a 17.4 kN fatigue load limit Pu. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51315 cannot. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "At 75 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 513 heavy section buys capacity with a larger 135 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51315 has no radial capacity at all.",
      "Shock thrust above C0a 395 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The Ca 171/C0a 395 kN ratings and 17.4 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51315; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51315?",
        "a": "51315 is a single-direction thrust ball bearing to ISO 104: 75 mm shaft-washer bore, 135 mm outside diameter, 44 mm stack height (2.953 x 5.315 x 1.732 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 171 kN, C0a 395 kN and a 17.4 kN fatigue load limit Pu; the grease limiting speed is 1,300 r/min and the oil rating 1,800 r/min; mass about 2610 g."
      },
      {
        "q": "How is the 51315 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 15 encodes the 75 mm bore (bore code x 5). The 135 mm OD and 44 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51315 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51315?",
        "a": "At the 1,300 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51315?",
        "a": "The 75/135/44 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 171 kN / C0a 395 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51315-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51315"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51415",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51415",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 269,
    "static_load_kN": 615,
    "fatigue_load_limit_kN": 25.6,
    "limiting_speed_rpm": 940,
    "max_rpm": 940,
    "speed_oil_rpm": 1400,
    "weight_g": 5970,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The extra-heavy 51400 thrust family entry 51415 stacks a shaft washer, ball-and-cage set and housing washer into 65 mm of height over a 75 mm bore. Two fields make up the code — 514 is the dimension series (extra-heavy 51400 thrust family) and 15 encodes the 75 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. Size selection ends with the minimum-load check: at the 940 r/min class speed, the balls need a defined axial preload to keep rolling instead of skidding. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "At 75 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Single-direction means exactly that: thrust on 51415 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Single-direction means exactly that: thrust on 51415 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 269/C0a 615 kN ratings and 25.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51415; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51415?",
        "a": "51415 is a single-direction thrust ball bearing to ISO 104: 75 mm shaft-washer bore, 160 mm outside diameter, 65 mm stack height (2.953 x 6.299 x 2.559 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 269 kN, C0a 615 kN and a 25.6 kN fatigue load limit Pu; the grease limiting speed is 940 r/min and the oil rating 1,400 r/min; mass about 5970 g."
      },
      {
        "q": "How is the 51415 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 15 encodes the 75 mm bore (bore code x 5). The 160 mm OD and 65 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51415 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51415?",
        "a": "At the 940 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51415?",
        "a": "The 75/160/65 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 269 kN / C0a 615 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51415-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51415"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51116",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51116",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 80,
    "D_mm": 105,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 44.5,
    "static_load_kN": 141,
    "fatigue_load_limit_kN": 6.35,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "speed_oil_rpm": 3100,
    "weight_g": 422,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51116 is the 80 mm member of NTN's light-section 51100 thrust family: 105 mm across the washers, 19 mm tall. Decoding 51116: 511 is the dimension series (light-section 51100 thrust family), with 16 encodes the 80 mm bore (bore code x 5). The static margin, C0a 141 kN against Ca 44.5 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51116 cannot. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "At 80 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 80 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "The C0a of 141 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Shock thrust above C0a 141 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 44.5/C0a 141 kN ratings and 6.35 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51116; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51116?",
        "a": "51116 is a single-direction thrust ball bearing to ISO 104: 80 mm shaft-washer bore, 105 mm outside diameter, 19 mm stack height (3.15 x 4.134 x 0.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 44.5 kN, C0a 141 kN and a 6.35 kN fatigue load limit Pu; the grease limiting speed is 2,200 r/min and the oil rating 3,100 r/min; mass about 422 g."
      },
      {
        "q": "How is the 51116 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 16 encodes the 80 mm bore (bore code x 5). The 105 mm OD and 19 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51116 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51116?",
        "a": "At the 2,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51116?",
        "a": "The 80/105/19 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 44.5 kN / C0a 141 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51116-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51116"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51216",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51216",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 80,
    "D_mm": 115,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 78.5,
    "static_load_kN": 218,
    "fatigue_load_limit_kN": 9.85,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "speed_oil_rpm": 2400,
    "weight_g": 916,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51216 is an NTN single-direction thrust ball bearing of the medium-section 51200 thrust family: 80 mm bore, 115 mm outside diameter, 28 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. Two fields make up the code — 512 is the dimension series (medium-section 51200 thrust family) and 16 encodes the 80 mm bore (bore code x 5). Catalogue axial dynamic rating Ca is 78.5 kN against C0a 218 kN — a static/dynamic ratio of 2.78 that is the signature of a thrust raceway. If the duty is high speed with light thrust, check the minimum axial load formula first; a too-large thrust ball bearing fails by skid long before its Ca of 78.5 kN is ever approached. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "At 80 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 80 mm bore.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Shock thrust above C0a 218 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Swapping the shaft and housing washers is an easy assembly error on the 80 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The Ca 78.5/C0a 218 kN ratings and 9.85 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51216; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51216?",
        "a": "51216 is a single-direction thrust ball bearing to ISO 104: 80 mm shaft-washer bore, 115 mm outside diameter, 28 mm stack height (3.15 x 4.528 x 1.102 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 78.5 kN, C0a 218 kN and a 9.85 kN fatigue load limit Pu; the grease limiting speed is 1,700 r/min and the oil rating 2,400 r/min; mass about 916 g."
      },
      {
        "q": "How is the 51216 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 16 encodes the 80 mm bore (bore code x 5). The 115 mm OD and 28 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51216 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51216?",
        "a": "At the 1,700 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51216?",
        "a": "The 80/115/28 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 78.5 kN / C0a 218 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51216-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51216"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51316",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51316",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 44,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 176,
    "static_load_kN": 425,
    "fatigue_load_limit_kN": 18.2,
    "limiting_speed_rpm": 1200,
    "max_rpm": 1200,
    "speed_oil_rpm": 1800,
    "weight_g": 2720,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51316 belongs to the heavy-section 51300 thrust family of single-direction thrust ball bearings: 80 / 140 / 44 mm (shaft bore / OD / height). Reading the code: 513 is the dimension series (heavy-section 51300 thrust family), and 16 encodes the 80 mm bore (bore code x 5). At 44 mm of height the stack is compact for the 80 mm bore class, trading section height for the heavy-section load level. For a 80 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "At 80 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 513 heavy section buys capacity with a larger 140 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Swapping the shaft and housing washers is an easy assembly error on the 80 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51316 stack height of 44 mm and washer set differ from the double-direction execution.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 176 kN never saves a bearing that is running too lightly loaded at 1,200 r/min.",
      "The Ca 176/C0a 425 kN ratings and 18.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51316; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51316?",
        "a": "51316 is a single-direction thrust ball bearing to ISO 104: 80 mm shaft-washer bore, 140 mm outside diameter, 44 mm stack height (3.15 x 5.512 x 1.732 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 176 kN, C0a 425 kN and a 18.2 kN fatigue load limit Pu; the grease limiting speed is 1,200 r/min and the oil rating 1,800 r/min; mass about 2720 g."
      },
      {
        "q": "How is the 51316 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 16 encodes the 80 mm bore (bore code x 5). The 140 mm OD and 44 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51316 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51316?",
        "a": "At the 1,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51316?",
        "a": "The 80/140/44 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 176 kN / C0a 425 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51316-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×44 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51316"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51416",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51416",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 68,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 270,
    "static_load_kN": 620,
    "fatigue_load_limit_kN": 25,
    "limiting_speed_rpm": 890,
    "max_rpm": 890,
    "speed_oil_rpm": 1300,
    "weight_g": 7770,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 80 x 170 x 68 mm, NTN 51416 sits in the extra-heavy 51400 thrust family of the single-direction thrust programme. Decoding 51416: 514 is the dimension series (extra-heavy 51400 thrust family), with 16 encodes the 80 mm bore (bore code x 5). On speed, the grease limiting speed is 890 r/min and the oil rating 1,300 r/min. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 620 kN class figures at the cost of OD and height. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "At 80 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "The 890 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51416 has no radial capacity at all.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The Ca 270/C0a 620 kN ratings and 25 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51416; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51416?",
        "a": "51416 is a single-direction thrust ball bearing to ISO 104: 80 mm shaft-washer bore, 170 mm outside diameter, 68 mm stack height (3.15 x 6.693 x 2.677 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 270 kN, C0a 620 kN and a 25 kN fatigue load limit Pu; the grease limiting speed is 890 r/min and the oil rating 1,300 r/min; mass about 7770 g."
      },
      {
        "q": "How is the 51416 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 16 encodes the 80 mm bore (bore code x 5). The 170 mm OD and 68 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51416 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51416?",
        "a": "At the 890 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51416?",
        "a": "The 80/170/68 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 270 kN / C0a 620 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51416-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×68 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51416"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51117",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51117",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 85,
    "D_mm": 110,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 46,
    "static_load_kN": 150,
    "fatigue_load_limit_kN": 6.8,
    "limiting_speed_rpm": 2100,
    "max_rpm": 2100,
    "speed_oil_rpm": 3000,
    "weight_g": 444,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the light-section 51100 thrust family, 51117 measures 85 mm through the shaft washer, 110 mm over the outside and 19 mm in assembled height. NTN builds the number from 511 is the dimension series (light-section 51100 thrust family); 17 encodes the 85 mm bore (bore code x 5). The washer section here is 12.5 mm of radial height, and the catalogue couples it with Ca 46 kN / C0a 150 kN. For a 85 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "At 85 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 85 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The 2,100 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The C0a of 150 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The Ca 46/C0a 150 kN ratings and 6.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51117; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51117?",
        "a": "51117 is a single-direction thrust ball bearing to ISO 104: 85 mm shaft-washer bore, 110 mm outside diameter, 19 mm stack height (3.346 x 4.331 x 0.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 46 kN, C0a 150 kN and a 6.8 kN fatigue load limit Pu; the grease limiting speed is 2,100 r/min and the oil rating 3,000 r/min; mass about 444 g."
      },
      {
        "q": "How is the 51117 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 17 encodes the 85 mm bore (bore code x 5). The 110 mm OD and 19 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51117 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51117?",
        "a": "At the 2,100 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51117?",
        "a": "The 85/110/19 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 46 kN / C0a 150 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51117-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51117"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51217",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51217",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 85,
    "D_mm": 125,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 95.5,
    "static_load_kN": 264,
    "fatigue_load_limit_kN": 11.6,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "speed_oil_rpm": 2200,
    "weight_g": 1250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51217 appears as a medium-section 51200 thrust family bearing with a 85 mm shaft washer, a 125 mm housing diameter and 31 mm of stack height. Decoding 51217: 512 is the dimension series (medium-section 51200 thrust family), with 17 encodes the 85 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 95.5 kN rating assumes the load arrives truly axial. Size selection ends with the minimum-load check: at the 1,600 r/min class speed, the balls need a defined axial preload to keep rolling instead of skidding. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "At 85 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 85 mm bore.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51217 stack height of 31 mm and washer set differ from the double-direction execution.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51217 stack height of 31 mm and washer set differ from the double-direction execution.",
      "The Ca 95.5/C0a 264 kN ratings and 11.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51217; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51217?",
        "a": "51217 is a single-direction thrust ball bearing to ISO 104: 85 mm shaft-washer bore, 125 mm outside diameter, 31 mm stack height (3.346 x 4.921 x 1.22 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 95.5 kN, C0a 264 kN and a 11.6 kN fatigue load limit Pu; the grease limiting speed is 1,600 r/min and the oil rating 2,200 r/min; mass about 1250 g."
      },
      {
        "q": "How is the 51217 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 17 encodes the 85 mm bore (bore code x 5). The 125 mm OD and 31 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51217 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51217?",
        "a": "At the 1,600 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51217?",
        "a": "The 85/125/31 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 95.5 kN / C0a 264 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51217-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51217"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51317",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51317",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 49,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 206,
    "static_load_kN": 490,
    "fatigue_load_limit_kN": 20.3,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "speed_oil_rpm": 1600,
    "weight_g": 3520,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The heavy-section 51300 thrust family entry 51317 stacks a shaft washer, ball-and-cage set and housing washer into 49 mm of height over a 85 mm bore. Two fields make up the code — 513 is the dimension series (heavy-section 51300 thrust family) and 17 encodes the 85 mm bore (bore code x 5). The static margin, C0a 490 kN against Ca 206 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. Against a thrust roller bearing of the same 85 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "At 85 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 513 heavy section buys capacity with a larger 150 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "The C0a of 490 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Single-direction means exactly that: thrust on 51317 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Shock thrust above C0a 490 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 206/C0a 490 kN ratings and 20.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51317; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51317?",
        "a": "51317 is a single-direction thrust ball bearing to ISO 104: 85 mm shaft-washer bore, 150 mm outside diameter, 49 mm stack height (3.346 x 5.906 x 1.929 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 206 kN, C0a 490 kN and a 20.3 kN fatigue load limit Pu; the grease limiting speed is 1,100 r/min and the oil rating 1,600 r/min; mass about 3520 g."
      },
      {
        "q": "How is the 51317 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 17 encodes the 85 mm bore (bore code x 5). The 150 mm OD and 49 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51317 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51317?",
        "a": "At the 1,100 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51317?",
        "a": "The 85/150/49 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 206 kN / C0a 490 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51317-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×49 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51317"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51417",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51417",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 72,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 288,
    "static_load_kN": 685,
    "fatigue_load_limit_kN": 26.8,
    "limiting_speed_rpm": 840,
    "max_rpm": 840,
    "speed_oil_rpm": 1200,
    "weight_g": 9170,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51417 is the 85 mm member of NTN's extra-heavy 51400 thrust family: 180 mm across the washers, 72 mm tall. NTN builds the number from 514 is the dimension series (extra-heavy 51400 thrust family); 17 encodes the 85 mm bore (bore code x 5). Catalogue axial dynamic rating Ca is 288 kN against C0a 685 kN — a static/dynamic ratio of 2.38 that is the signature of a thrust raceway. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 180 mm OD already tilts the raceway and concentrates the 685 kN static capacity on a few balls. ",
    "applications": [
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "At 85 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51417 stack height of 72 mm and washer set differ from the double-direction execution.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 288 kN never saves a bearing that is running too lightly loaded at 840 r/min.",
      "Swapping the shaft and housing washers is an easy assembly error on the 85 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The Ca 288/C0a 685 kN ratings and 26.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51417; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51417?",
        "a": "51417 is a single-direction thrust ball bearing to ISO 104: 85 mm shaft-washer bore, 180 mm outside diameter, 72 mm stack height (3.346 x 7.087 x 2.835 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 288 kN, C0a 685 kN and a 26.8 kN fatigue load limit Pu; the grease limiting speed is 840 r/min and the oil rating 1,200 r/min; mass about 9170 g."
      },
      {
        "q": "How is the 51417 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 17 encodes the 85 mm bore (bore code x 5). The 180 mm OD and 72 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51417 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51417?",
        "a": "At the 840 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51417?",
        "a": "The 85/180/72 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 288 kN / C0a 685 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51417-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51417",
      "51417"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51118",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51118",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 90,
    "D_mm": 120,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 59.5,
    "static_load_kN": 190,
    "fatigue_load_limit_kN": 8.35,
    "limiting_speed_rpm": 1900,
    "max_rpm": 1900,
    "speed_oil_rpm": 2700,
    "weight_g": 687,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51118 is an NTN single-direction thrust ball bearing of the light-section 51100 thrust family: 90 mm bore, 120 mm outside diameter, 22 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. The designation is 511 is the dimension series (light-section 51100 thrust family) plus 18 encodes the 90 mm bore (bore code x 5). The ball-and-cage set is separable from both washers, which is why the mounting order (shaft washer first, then cage, then housing washer) matters. Against a thrust roller bearing of the same 90 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 120 mm OD already tilts the raceway and concentrates the 190 kN static capacity on a few balls. ",
    "applications": [
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "At 90 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 90 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Shock thrust above C0a 190 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Shock thrust above C0a 190 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51118 has no radial capacity at all.",
      "The Ca 59.5/C0a 190 kN ratings and 8.35 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51118; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51118?",
        "a": "51118 is a single-direction thrust ball bearing to ISO 104: 90 mm shaft-washer bore, 120 mm outside diameter, 22 mm stack height (3.543 x 4.724 x 0.866 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 59.5 kN, C0a 190 kN and a 8.35 kN fatigue load limit Pu; the grease limiting speed is 1,900 r/min and the oil rating 2,700 r/min; mass about 687 g."
      },
      {
        "q": "How is the 51118 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 18 encodes the 90 mm bore (bore code x 5). The 120 mm OD and 22 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51118 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51118?",
        "a": "At the 1,900 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51118?",
        "a": "The 90/120/22 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 59.5 kN / C0a 190 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51118-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51118"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51218",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51218",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 90,
    "D_mm": 135,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 117,
    "static_load_kN": 325,
    "fatigue_load_limit_kN": 13.9,
    "limiting_speed_rpm": 1400,
    "max_rpm": 1400,
    "speed_oil_rpm": 2000,
    "weight_g": 1700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51218 belongs to the medium-section 51200 thrust family of single-direction thrust ball bearings: 90 / 135 / 35 mm (shaft bore / OD / height). NTN builds the number from 512 is the dimension series (medium-section 51200 thrust family); 18 encodes the 90 mm bore (bore code x 5). NTN prints 117 kN axial dynamic and 325 kN axial static for this size and a 13.9 kN fatigue load limit Pu. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 325 kN class figures at the cost of OD and height. The shaft washer (bore 90 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "At 90 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 90 mm bore.",
      "The 1,400 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "Single-direction means exactly that: thrust on 51218 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The Ca 117/C0a 325 kN ratings and 13.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51218; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51218?",
        "a": "51218 is a single-direction thrust ball bearing to ISO 104: 90 mm shaft-washer bore, 135 mm outside diameter, 35 mm stack height (3.543 x 5.315 x 1.378 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 117 kN, C0a 325 kN and a 13.9 kN fatigue load limit Pu; the grease limiting speed is 1,400 r/min and the oil rating 2,000 r/min; mass about 1700 g."
      },
      {
        "q": "How is the 51218 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 18 encodes the 90 mm bore (bore code x 5). The 135 mm OD and 35 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51218 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51218?",
        "a": "At the 1,400 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51218?",
        "a": "The 90/135/35 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 117 kN / C0a 325 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51218-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×135×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51218"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51318",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51318",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 90,
    "D_mm": 155,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 213,
    "static_load_kN": 525,
    "fatigue_load_limit_kN": 21.3,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "speed_oil_rpm": 1600,
    "weight_g": 3740,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 90 x 155 x 50 mm, NTN 51318 sits in the heavy-section 51300 thrust family of the single-direction thrust programme. Decoding 51318: 513 is the dimension series (heavy-section 51300 thrust family), with 18 encodes the 90 mm bore (bore code x 5). The washer section here is 32.5 mm of radial height, and the catalogue couples it with Ca 213 kN / C0a 525 kN. If the duty is high speed with light thrust, check the minimum axial load formula first; a too-large thrust ball bearing fails by skid long before its Ca of 213 kN is ever approached. The shaft washer (bore 90 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "At 90 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 513 heavy section buys capacity with a larger 155 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51318 has no radial capacity at all.",
      "The C0a of 525 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The Ca 213/C0a 525 kN ratings and 21.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51318; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51318?",
        "a": "51318 is a single-direction thrust ball bearing to ISO 104: 90 mm shaft-washer bore, 155 mm outside diameter, 50 mm stack height (3.543 x 6.102 x 1.969 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 213 kN, C0a 525 kN and a 21.3 kN fatigue load limit Pu; the grease limiting speed is 1,100 r/min and the oil rating 1,600 r/min; mass about 3740 g."
      },
      {
        "q": "How is the 51318 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 18 encodes the 90 mm bore (bore code x 5). The 155 mm OD and 50 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51318 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51318?",
        "a": "At the 1,100 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51318?",
        "a": "The 90/155/50 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 213 kN / C0a 525 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51318-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×155×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51318"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51418",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51418",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 77,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 305,
    "static_load_kN": 750,
    "fatigue_load_limit_kN": 28.6,
    "limiting_speed_rpm": 790,
    "max_rpm": 790,
    "speed_oil_rpm": 1100,
    "weight_g": 11000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the extra-heavy 51400 thrust family, 51418 measures 90 mm through the shaft washer, 190 mm over the outside and 77 mm in assembled height. The designation is 514 is the dimension series (extra-heavy 51400 thrust family) plus 18 encodes the 90 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 305 kN rating assumes the load arrives truly axial. Choose the extra-heavy 51400 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "At 90 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51418 has no radial capacity at all.",
      "Swapping the shaft and housing washers is an easy assembly error on the 90 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51418 stack height of 77 mm and washer set differ from the double-direction execution.",
      "The Ca 305/C0a 750 kN ratings and 28.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51418; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51418?",
        "a": "51418 is a single-direction thrust ball bearing to ISO 104: 90 mm shaft-washer bore, 190 mm outside diameter, 77 mm stack height (3.543 x 7.48 x 3.031 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 305 kN, C0a 750 kN and a 28.6 kN fatigue load limit Pu; the grease limiting speed is 790 r/min and the oil rating 1,100 r/min; mass about 11000 g."
      },
      {
        "q": "How is the 51418 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 18 encodes the 90 mm bore (bore code x 5). The 190 mm OD and 77 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51418 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51418?",
        "a": "At the 790 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51418?",
        "a": "The 90/190/77 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 305 kN / C0a 750 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51418-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=226",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51418",
      "51418"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51120",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51120",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 100,
    "D_mm": 135,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 85,
    "static_load_kN": 268,
    "fatigue_load_limit_kN": 11.2,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "speed_oil_rpm": 2400,
    "weight_g": 987,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51120 belongs to the light-section 51100 thrust family of single-direction thrust ball bearings: 100 / 135 / 25 mm (shaft bore / OD / height). NTN builds the number from 511 is the dimension series (light-section 51100 thrust family); 20 encodes the 100 mm bore (bore code x 5). Catalogue axial dynamic rating Ca is 85 kN against C0a 268 kN — a static/dynamic ratio of 3.15 that is the signature of a thrust raceway. Choose the light-section 51100 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "At 100 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 100 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51120 has no radial capacity at all.",
      "Single-direction means exactly that: thrust on 51120 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Swapping the shaft and housing washers is an easy assembly error on the 100 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The Ca 85/C0a 268 kN ratings and 11.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51120; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51120?",
        "a": "51120 is a single-direction thrust ball bearing to ISO 104: 100 mm shaft-washer bore, 135 mm outside diameter, 25 mm stack height (3.937 x 5.315 x 0.984 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 85 kN, C0a 268 kN and a 11.2 kN fatigue load limit Pu; the grease limiting speed is 1,700 r/min and the oil rating 2,400 r/min; mass about 987 g."
      },
      {
        "q": "How is the 51120 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 20 encodes the 100 mm bore (bore code x 5). The 135 mm OD and 25 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51120 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51120?",
        "a": "At the 1,700 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51120?",
        "a": "The 100/135/25 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 85 kN / C0a 268 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51120-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51120"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51220",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51220",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 100,
    "D_mm": 150,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 147,
    "static_load_kN": 410,
    "fatigue_load_limit_kN": 16.6,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "speed_oil_rpm": 1800,
    "weight_g": 2290,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 100 x 150 x 38 mm, NTN 51220 sits in the medium-section 51200 thrust family of the single-direction thrust programme. Decoding 51220: 512 is the dimension series (medium-section 51200 thrust family), with 20 encodes the 100 mm bore (bore code x 5). Catalogue mass is about 2290 g for the full washer-and-cage stack. For a 100 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "At 100 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 100 mm bore.",
      "Single-direction means exactly that: thrust on 51220 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 147 kN never saves a bearing that is running too lightly loaded at 1,300 r/min.",
      "The 1,300 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The Ca 147/C0a 410 kN ratings and 16.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51220; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51220?",
        "a": "51220 is a single-direction thrust ball bearing to ISO 104: 100 mm shaft-washer bore, 150 mm outside diameter, 38 mm stack height (3.937 x 5.906 x 1.496 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 147 kN, C0a 410 kN and a 16.6 kN fatigue load limit Pu; the grease limiting speed is 1,300 r/min and the oil rating 1,800 r/min; mass about 2290 g."
      },
      {
        "q": "How is the 51220 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 20 encodes the 100 mm bore (bore code x 5). The 150 mm OD and 38 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51220 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51220?",
        "a": "At the 1,300 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51220?",
        "a": "The 100/150/38 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 147 kN / C0a 410 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51220-SKF",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×150×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51220"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51320",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51320",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 100,
    "D_mm": 170,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 237,
    "static_load_kN": 595,
    "fatigue_load_limit_kN": 23.1,
    "limiting_speed_rpm": 990,
    "max_rpm": 990,
    "speed_oil_rpm": 1400,
    "weight_g": 4880,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the heavy-section 51300 thrust family, 51320 measures 100 mm through the shaft washer, 170 mm over the outside and 55 mm in assembled height. Two fields make up the code — 513 is the dimension series (heavy-section 51300 thrust family) and 20 encodes the 100 mm bore (bore code x 5). On speed, the grease limiting speed is 990 r/min and the oil rating 1,400 r/min. The 100/170/55 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "heavy press and forging-machine thrust seats",
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "At 100 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 513 heavy section buys capacity with a larger 170 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51320 stack height of 55 mm and washer set differ from the double-direction execution.",
      "Swapping the shaft and housing washers is an easy assembly error on the 100 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The Ca 237/C0a 595 kN ratings and 23.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51320; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51320?",
        "a": "51320 is a single-direction thrust ball bearing to ISO 104: 100 mm shaft-washer bore, 170 mm outside diameter, 55 mm stack height (3.937 x 6.693 x 2.165 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 237 kN, C0a 595 kN and a 23.1 kN fatigue load limit Pu; the grease limiting speed is 990 r/min and the oil rating 1,400 r/min; mass about 4880 g."
      },
      {
        "q": "How is the 51320 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 20 encodes the 100 mm bore (bore code x 5). The 170 mm OD and 55 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51320 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51320?",
        "a": "At the 990 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51320?",
        "a": "The 100/170/55 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 237 kN / C0a 595 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51320-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51320"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51420",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51420",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 100,
    "D_mm": 210,
    "B_mm": 85,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 370,
    "static_load_kN": 970,
    "fatigue_load_limit_kN": 35,
    "limiting_speed_rpm": 710,
    "max_rpm": 710,
    "speed_oil_rpm": 1000,
    "weight_g": 14700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51420 appears as a extra-heavy 51400 thrust family bearing with a 100 mm shaft washer, a 210 mm housing diameter and 85 mm of stack height. NTN builds the number from 514 is the dimension series (extra-heavy 51400 thrust family); 20 encodes the 100 mm bore (bore code x 5). The ball-and-cage set is separable from both washers, which is why the mounting order (shaft washer first, then cage, then housing washer) matters. If the duty is high speed with light thrust, check the minimum axial load formula first; a too-large thrust ball bearing fails by skid long before its Ca of 370 kN is ever approached. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "At 100 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 514 extra-heavy section is the top of the thrust-ball plan at this bore; beyond it the catalogue moves to spherical roller thrust bearings.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The C0a of 970 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51420 has no radial capacity at all.",
      "The Ca 370/C0a 970 kN ratings and 35 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51420; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51420?",
        "a": "51420 is a single-direction thrust ball bearing to ISO 104: 100 mm shaft-washer bore, 210 mm outside diameter, 85 mm stack height (3.937 x 8.268 x 3.346 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 370 kN, C0a 970 kN and a 35 kN fatigue load limit Pu; the grease limiting speed is 710 r/min and the oil rating 1,000 r/min; mass about 14700 g."
      },
      {
        "q": "How is the 51420 designation structured?",
        "a": "514 is the dimension series (extra-heavy 51400 thrust family); 20 encodes the 100 mm bore (bore code x 5). The 210 mm OD and 85 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51420 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51420?",
        "a": "At the 710 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51420?",
        "a": "The 100/210/85 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 370 kN / C0a 970 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51420-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51420",
      "51420"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51122-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51122",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 110,
    "D_mm": 145,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 87,
    "static_load_kN": 288,
    "fatigue_load_limit_kN": 11.5,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "speed_oil_rpm": 2300,
    "weight_g": 1070,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51122 is an NTN single-direction thrust ball bearing of the light-section 51100 thrust family: 110 mm bore, 145 mm outside diameter, 25 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. The designation is 511 is the dimension series (light-section 51100 thrust family) plus 22 encodes the 110 mm bore (bore code x 5). The static margin, C0a 288 kN against Ca 87 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "At 110 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 110 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 87 kN never saves a bearing that is running too lightly loaded at 1,600 r/min.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Shock thrust above C0a 288 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 87/C0a 288 kN ratings and 11.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51122; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51122?",
        "a": "51122 is a single-direction thrust ball bearing to ISO 104: 110 mm shaft-washer bore, 145 mm outside diameter, 25 mm stack height (4.331 x 5.709 x 0.984 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 87 kN, C0a 288 kN and a 11.5 kN fatigue load limit Pu; the grease limiting speed is 1,600 r/min and the oil rating 2,300 r/min; mass about 1070 g."
      },
      {
        "q": "How is the 51122 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 22 encodes the 110 mm bore (bore code x 5). The 145 mm OD and 25 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51122 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51122?",
        "a": "At the 1,600 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51122?",
        "a": "The 110/145/25 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 87 kN / C0a 288 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51122",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51122",
      "51122-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51222-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51222",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 110,
    "D_mm": 160,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 153,
    "static_load_kN": 450,
    "fatigue_load_limit_kN": 17.5,
    "limiting_speed_rpm": 1200,
    "max_rpm": 1200,
    "speed_oil_rpm": 1800,
    "weight_g": 2460,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the medium-section 51200 thrust family, 51222 measures 110 mm through the shaft washer, 160 mm over the outside and 38 mm in assembled height. NTN builds the number from 512 is the dimension series (medium-section 51200 thrust family); 22 encodes the 110 mm bore (bore code x 5). At 38 mm of height the stack is compact for the 110 mm bore class, trading section height for the medium-section load level. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 450 kN class figures at the cost of OD and height. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "ship winch and capstan thrust shafts",
      "crusher main-shaft thrust supports",
      "large rotary-table and index-table thrust rings",
      "vertical water-pump and turbine thrust blocks"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "At 110 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 110 mm bore.",
      "The 1,200 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 153 kN never saves a bearing that is running too lightly loaded at 1,200 r/min.",
      "The Ca 153/C0a 450 kN ratings and 17.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51222; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51222?",
        "a": "51222 is a single-direction thrust ball bearing to ISO 104: 110 mm shaft-washer bore, 160 mm outside diameter, 38 mm stack height (4.331 x 6.299 x 1.496 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 153 kN, C0a 450 kN and a 17.5 kN fatigue load limit Pu; the grease limiting speed is 1,200 r/min and the oil rating 1,800 r/min; mass about 2460 g."
      },
      {
        "q": "How is the 51222 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 22 encodes the 110 mm bore (bore code x 5). The 160 mm OD and 38 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51222 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51222?",
        "a": "At the 1,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51222?",
        "a": "The 110/160/38 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 153 kN / C0a 450 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51222",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×160×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51222",
      "51222-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51322",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51322",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 110,
    "D_mm": 190,
    "B_mm": 63,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 267,
    "static_load_kN": 705,
    "fatigue_load_limit_kN": 25.9,
    "limiting_speed_rpm": 870,
    "max_rpm": 870,
    "speed_oil_rpm": 1200,
    "weight_g": 7670,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51322 appears as a heavy-section 51300 thrust family bearing with a 110 mm shaft washer, a 190 mm housing diameter and 63 mm of stack height. NTN builds the number from 513 is the dimension series (heavy-section 51300 thrust family); 22 encodes the 110 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 267 kN rating assumes the load arrives truly axial. For a 110 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. The shaft washer (bore 110 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "vertical water-pump and turbine thrust blocks",
      "large crane hook and swivel assemblies",
      "rolling-mill screwdown and adjustment screws",
      "heavy press and forging-machine thrust seats"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "At 110 mm bore the washers are heavy enough to sag out of square during assembly — support the stack horizontally where possible and verify face runout before loading.",
      "The 513 heavy section buys capacity with a larger 190 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Swapping the shaft and housing washers is an easy assembly error on the 110 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The C0a of 705 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51322 stack height of 63 mm and washer set differ from the double-direction execution.",
      "The Ca 267/C0a 705 kN ratings and 25.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51322; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51322?",
        "a": "51322 is a single-direction thrust ball bearing to ISO 104: 110 mm shaft-washer bore, 190 mm outside diameter, 63 mm stack height (4.331 x 7.48 x 2.48 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 267 kN, C0a 705 kN and a 25.9 kN fatigue load limit Pu; the grease limiting speed is 870 r/min and the oil rating 1,200 r/min; mass about 7670 g."
      },
      {
        "q": "How is the 51322 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 22 encodes the 110 mm bore (bore code x 5). The 190 mm OD and 63 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51322 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51322?",
        "a": "At the 870 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51322?",
        "a": "The 110/190/63 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 267 kN / C0a 705 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51322-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×190×63 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51322",
      "51322"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51124-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51124",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 120,
    "D_mm": 155,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 89,
    "static_load_kN": 310,
    "fatigue_load_limit_kN": 11.8,
    "limiting_speed_rpm": 1500,
    "max_rpm": 1500,
    "speed_oil_rpm": 2200,
    "weight_g": 1110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51124 is an NTN single-direction thrust ball bearing of the light-section 51100 thrust family: 120 mm bore, 155 mm outside diameter, 25 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. NTN builds the number from 511 is the dimension series (light-section 51100 thrust family); 24 encodes the 120 mm bore (bore code x 5). Catalogue mass is about 1110 g for the full washer-and-cage stack. Choose the light-section 51100 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "For a 120 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 120 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51124 has no radial capacity at all.",
      "Single-direction means exactly that: thrust on 51124 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The 1,500 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The Ca 89/C0a 310 kN ratings and 11.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51124; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51124?",
        "a": "51124 is a single-direction thrust ball bearing to ISO 104: 120 mm shaft-washer bore, 155 mm outside diameter, 25 mm stack height (4.724 x 6.102 x 0.984 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 89 kN, C0a 310 kN and a 11.8 kN fatigue load limit Pu; the grease limiting speed is 1,500 r/min and the oil rating 2,200 r/min; mass about 1110 g."
      },
      {
        "q": "How is the 51124 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 24 encodes the 120 mm bore (bore code x 5). The 155 mm OD and 25 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51124 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51124?",
        "a": "At the 1,500 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51124?",
        "a": "The 120/155/25 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 89 kN / C0a 310 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51124",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51124",
      "51124-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51224-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51224",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 120,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 154,
    "static_load_kN": 470,
    "fatigue_load_limit_kN": 17.7,
    "limiting_speed_rpm": 1200,
    "max_rpm": 1200,
    "speed_oil_rpm": 1700,
    "weight_g": 2710,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51224 appears as a medium-section 51200 thrust family bearing with a 120 mm shaft washer, a 170 mm housing diameter and 39 mm of stack height. The designation is 512 is the dimension series (medium-section 51200 thrust family) plus 24 encodes the 120 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. For a 120 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 120 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 120 mm bore.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51224 has no radial capacity at all.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 154 kN never saves a bearing that is running too lightly loaded at 1,200 r/min.",
      "Single-direction means exactly that: thrust on 51224 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 154/C0a 470 kN ratings and 17.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51224; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51224?",
        "a": "51224 is a single-direction thrust ball bearing to ISO 104: 120 mm shaft-washer bore, 170 mm outside diameter, 39 mm stack height (4.724 x 6.693 x 1.535 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 154 kN, C0a 470 kN and a 17.7 kN fatigue load limit Pu; the grease limiting speed is 1,200 r/min and the oil rating 1,700 r/min; mass about 2710 g."
      },
      {
        "q": "How is the 51224 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 24 encodes the 120 mm bore (bore code x 5). The 170 mm OD and 39 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51224 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51224?",
        "a": "At the 1,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51224?",
        "a": "The 120/170/39 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 154 kN / C0a 470 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51224",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 120×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51224",
      "51224-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51324",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51324",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 120,
    "D_mm": 210,
    "B_mm": 70,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 296,
    "static_load_kN": 805,
    "fatigue_load_limit_kN": 28.3,
    "limiting_speed_rpm": 780,
    "max_rpm": 780,
    "speed_oil_rpm": 1100,
    "weight_g": 10800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The heavy-section 51300 thrust family entry 51324 stacks a shaft washer, ball-and-cage set and housing washer into 70 mm of height over a 120 mm bore. Reading the code: 513 is the dimension series (heavy-section 51300 thrust family), and 24 encodes the 120 mm bore (bore code x 5). At 70 mm of height the stack is compact for the 120 mm bore class, trading section height for the heavy-section load level. If the duty is high speed with light thrust, check the minimum axial load formula first; a too-large thrust ball bearing fails by skid long before its Ca of 296 kN is ever approached. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 120 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 513 heavy section buys capacity with a larger 210 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 296 kN never saves a bearing that is running too lightly loaded at 780 r/min.",
      "The Ca 296/C0a 805 kN ratings and 28.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51324; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51324?",
        "a": "51324 is a single-direction thrust ball bearing to ISO 104: 120 mm shaft-washer bore, 210 mm outside diameter, 70 mm stack height (4.724 x 8.268 x 2.756 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 296 kN, C0a 805 kN and a 28.3 kN fatigue load limit Pu; the grease limiting speed is 780 r/min and the oil rating 1,100 r/min; mass about 10800 g."
      },
      {
        "q": "How is the 51324 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 24 encodes the 120 mm bore (bore code x 5). The 210 mm OD and 70 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51324 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51324?",
        "a": "At the 780 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51324?",
        "a": "The 120/210/70 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 296 kN / C0a 805 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51324-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 120×210×70 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51324",
      "51324"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51126-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51126",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 130,
    "D_mm": 170,
    "B_mm": 30,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 104,
    "static_load_kN": 350,
    "fatigue_load_limit_kN": 13,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "speed_oil_rpm": 1900,
    "weight_g": 1730,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51126 is an NTN single-direction thrust ball bearing of the light-section 51100 thrust family: 130 mm bore, 170 mm outside diameter, 30 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. The designation is 511 is the dimension series (light-section 51100 thrust family) plus 26 encodes the 130 mm bore (bore code x 5). On speed, the grease limiting speed is 1,300 r/min and the oil rating 1,900 r/min. Choose the light-section 51100 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 130 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 130 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "The C0a of 350 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The C0a of 350 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The Ca 104/C0a 350 kN ratings and 13 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51126; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51126?",
        "a": "51126 is a single-direction thrust ball bearing to ISO 104: 130 mm shaft-washer bore, 170 mm outside diameter, 30 mm stack height (5.118 x 6.693 x 1.181 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 104 kN, C0a 350 kN and a 13 kN fatigue load limit Pu; the grease limiting speed is 1,300 r/min and the oil rating 1,900 r/min; mass about 1730 g."
      },
      {
        "q": "How is the 51126 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 26 encodes the 130 mm bore (bore code x 5). The 170 mm OD and 30 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51126 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51126?",
        "a": "At the 1,300 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51126?",
        "a": "The 130/170/30 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 104 kN / C0a 350 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51126",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×170×30 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51126",
      "51126-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51226-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51226",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 130,
    "D_mm": 190,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 191,
    "static_load_kN": 565,
    "fatigue_load_limit_kN": 20.2,
    "limiting_speed_rpm": 1000,
    "max_rpm": 1000,
    "speed_oil_rpm": 1500,
    "weight_g": 4220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51226 appears as a medium-section 51200 thrust family bearing with a 130 mm shaft washer, a 190 mm housing diameter and 45 mm of stack height. NTN builds the number from 512 is the dimension series (medium-section 51200 thrust family); 26 encodes the 130 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 191 kN rating assumes the load arrives truly axial. Against a thrust roller bearing of the same 130 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 190 mm OD already tilts the raceway and concentrates the 565 kN static capacity on a few balls. ",
    "applications": [
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "For a 130 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 130 mm bore.",
      "Single-direction means exactly that: thrust on 51226 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51226 stack height of 45 mm and washer set differ from the double-direction execution.",
      "The Ca 191/C0a 565 kN ratings and 20.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51226; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51226?",
        "a": "51226 is a single-direction thrust ball bearing to ISO 104: 130 mm shaft-washer bore, 190 mm outside diameter, 45 mm stack height (5.118 x 7.48 x 1.772 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 191 kN, C0a 565 kN and a 20.2 kN fatigue load limit Pu; the grease limiting speed is 1,000 r/min and the oil rating 1,500 r/min; mass about 4220 g."
      },
      {
        "q": "How is the 51226 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 26 encodes the 130 mm bore (bore code x 5). The 190 mm OD and 45 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51226 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51226?",
        "a": "At the 1,000 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51226?",
        "a": "The 130/190/45 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 191 kN / C0a 565 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51226",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51226",
      "51226",
      "51226-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51326",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51326",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 130,
    "D_mm": 225,
    "B_mm": 75,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 330,
    "static_load_kN": 960,
    "fatigue_load_limit_kN": 32.5,
    "limiting_speed_rpm": 720,
    "max_rpm": 720,
    "speed_oil_rpm": 1000,
    "weight_g": 12700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51326 is the 130 mm member of NTN's heavy-section 51300 thrust family: 225 mm across the washers, 75 mm tall. Decoding 51326: 513 is the dimension series (heavy-section 51300 thrust family), with 26 encodes the 130 mm bore (bore code x 5). The washer section here is 47.5 mm of radial height, and the catalogue couples it with Ca 330 kN / C0a 960 kN. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 960 kN class figures at the cost of OD and height. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "For a 130 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 513 heavy section buys capacity with a larger 225 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Single-direction means exactly that: thrust on 51326 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Shock thrust above C0a 960 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The C0a of 960 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The Ca 330/C0a 960 kN ratings and 32.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51326; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51326?",
        "a": "51326 is a single-direction thrust ball bearing to ISO 104: 130 mm shaft-washer bore, 225 mm outside diameter, 75 mm stack height (5.118 x 8.858 x 2.953 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 330 kN, C0a 960 kN and a 32.5 kN fatigue load limit Pu; the grease limiting speed is 720 r/min and the oil rating 1,000 r/min; mass about 12700 g."
      },
      {
        "q": "How is the 51326 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 26 encodes the 130 mm bore (bore code x 5). The 225 mm OD and 75 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51326 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51326?",
        "a": "At the 720 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51326?",
        "a": "The 130/225/75 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 330 kN / C0a 960 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51326-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×225×75 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51326",
      "51326"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51128-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51128",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 140,
    "D_mm": 180,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 107,
    "static_load_kN": 375,
    "fatigue_load_limit_kN": 13.4,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "speed_oil_rpm": 1800,
    "weight_g": 1900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51128 is an NTN single-direction thrust ball bearing of the light-section 51100 thrust family: 140 mm bore, 180 mm outside diameter, 31 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. NTN builds the number from 511 is the dimension series (light-section 51100 thrust family); 28 encodes the 140 mm bore (bore code x 5). NTN prints 107 kN axial dynamic and 375 kN axial static for this size and a 13.4 kN fatigue load limit Pu. The 140/180/31 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "For a 140 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 140 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51128 stack height of 31 mm and washer set differ from the double-direction execution.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The Ca 107/C0a 375 kN ratings and 13.4 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51128; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51128?",
        "a": "51128 is a single-direction thrust ball bearing to ISO 104: 140 mm shaft-washer bore, 180 mm outside diameter, 31 mm stack height (5.512 x 7.087 x 1.22 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 107 kN, C0a 375 kN and a 13.4 kN fatigue load limit Pu; the grease limiting speed is 1,300 r/min and the oil rating 1,800 r/min; mass about 1900 g."
      },
      {
        "q": "How is the 51128 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 28 encodes the 140 mm bore (bore code x 5). The 180 mm OD and 31 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51128 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51128?",
        "a": "At the 1,300 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51128?",
        "a": "The 140/180/31 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 107 kN / C0a 375 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51128",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 140×180×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51128",
      "51128",
      "51128-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51228-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51228",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 140,
    "D_mm": 200,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 193,
    "static_load_kN": 595,
    "fatigue_load_limit_kN": 20.6,
    "limiting_speed_rpm": 980,
    "max_rpm": 980,
    "speed_oil_rpm": 1400,
    "weight_g": 4770,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51228 appears as a medium-section 51200 thrust family bearing with a 140 mm shaft washer, a 200 mm housing diameter and 46 mm of stack height. Decoding 51228: 512 is the dimension series (medium-section 51200 thrust family), with 28 encodes the 140 mm bore (bore code x 5). The static margin, C0a 595 kN against Ca 193 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. If the duty is high speed with light thrust, check the minimum axial load formula first; a too-large thrust ball bearing fails by skid long before its Ca of 193 kN is ever approached. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "For a 140 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 140 mm bore.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51228 stack height of 46 mm and washer set differ from the double-direction execution.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51228 has no radial capacity at all.",
      "Shock thrust above C0a 595 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 193/C0a 595 kN ratings and 20.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51228; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51228?",
        "a": "51228 is a single-direction thrust ball bearing to ISO 104: 140 mm shaft-washer bore, 200 mm outside diameter, 46 mm stack height (5.512 x 7.874 x 1.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 193 kN, C0a 595 kN and a 20.6 kN fatigue load limit Pu; the grease limiting speed is 980 r/min and the oil rating 1,400 r/min; mass about 4770 g."
      },
      {
        "q": "How is the 51228 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 28 encodes the 140 mm bore (bore code x 5). The 200 mm OD and 46 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51228 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51228?",
        "a": "At the 980 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51228?",
        "a": "The 140/200/46 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 193 kN / C0a 595 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51228",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51228",
      "51228",
      "51228-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51328",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51328",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 140,
    "D_mm": 240,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 350,
    "static_load_kN": 1050,
    "fatigue_load_limit_kN": 34.5,
    "limiting_speed_rpm": 670,
    "max_rpm": 670,
    "speed_oil_rpm": 960,
    "weight_g": 15300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51328 is an NTN single-direction thrust ball bearing of the heavy-section 51300 thrust family: 140 mm bore, 240 mm outside diameter, 80 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. The designation is 513 is the dimension series (heavy-section 51300 thrust family) plus 28 encodes the 140 mm bore (bore code x 5). Catalogue mass is about 15300 g for the full washer-and-cage stack. Choose the heavy-section 51300 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 140 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 513 heavy section buys capacity with a larger 240 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Single-direction means exactly that: thrust on 51328 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The 670 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The Ca 350/C0a 1050 kN ratings and 34.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51328; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51328?",
        "a": "51328 is a single-direction thrust ball bearing to ISO 104: 140 mm shaft-washer bore, 240 mm outside diameter, 80 mm stack height (5.512 x 9.449 x 3.15 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 350 kN, C0a 1050 kN and a 34.5 kN fatigue load limit Pu; the grease limiting speed is 670 r/min and the oil rating 960 r/min; mass about 15300 g."
      },
      {
        "q": "How is the 51328 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 28 encodes the 140 mm bore (bore code x 5). The 240 mm OD and 80 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51328 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51328?",
        "a": "At the 670 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51328?",
        "a": "The 140/240/80 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 350 kN / C0a 1050 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51328-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 140×240×80 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51328",
      "51328"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51130",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51130",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 150,
    "D_mm": 190,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 109,
    "static_load_kN": 400,
    "fatigue_load_limit_kN": 13.9,
    "limiting_speed_rpm": 1200,
    "max_rpm": 1200,
    "speed_oil_rpm": 1800,
    "weight_g": 2000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51130 is the 150 mm member of NTN's light-section 51100 thrust family: 190 mm across the washers, 31 mm tall. Reading the code: 511 is the dimension series (light-section 51100 thrust family), and 30 encodes the 150 mm bore (bore code x 5). NTN prints 109 kN axial dynamic and 400 kN axial static for this size and a 13.9 kN fatigue load limit Pu. Against a thrust roller bearing of the same 150 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. The shaft washer (bore 150 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 150 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 150 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Shock thrust above C0a 400 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51130 stack height of 31 mm and washer set differ from the double-direction execution.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The Ca 109/C0a 400 kN ratings and 13.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51130; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51130?",
        "a": "51130 is a single-direction thrust ball bearing to ISO 104: 150 mm shaft-washer bore, 190 mm outside diameter, 31 mm stack height (5.906 x 7.48 x 1.22 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 109 kN, C0a 400 kN and a 13.9 kN fatigue load limit Pu; the grease limiting speed is 1,200 r/min and the oil rating 1,800 r/min; mass about 2000 g."
      },
      {
        "q": "How is the 51130 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 30 encodes the 150 mm bore (bore code x 5). The 190 mm OD and 31 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51130 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51130?",
        "a": "At the 1,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51130?",
        "a": "The 150/190/31 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 109 kN / C0a 400 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51130-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51130",
      "51130"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51230",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51230",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 150,
    "D_mm": 215,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 227,
    "static_load_kN": 720,
    "fatigue_load_limit_kN": 24,
    "limiting_speed_rpm": 900,
    "max_rpm": 900,
    "speed_oil_rpm": 1300,
    "weight_g": 5870,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51230 is an NTN single-direction thrust ball bearing of the medium-section 51200 thrust family: 150 mm bore, 215 mm outside diameter, 50 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. The designation is 512 is the dimension series (medium-section 51200 thrust family) plus 30 encodes the 150 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 720 kN class figures at the cost of OD and height. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 150 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 150 mm bore.",
      "The 900 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51230 has no radial capacity at all.",
      "Single-direction means exactly that: thrust on 51230 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 227/C0a 720 kN ratings and 24 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51230; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51230?",
        "a": "51230 is a single-direction thrust ball bearing to ISO 104: 150 mm shaft-washer bore, 215 mm outside diameter, 50 mm stack height (5.906 x 8.465 x 1.969 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 227 kN, C0a 720 kN and a 24 kN fatigue load limit Pu; the grease limiting speed is 900 r/min and the oil rating 1,300 r/min; mass about 5870 g."
      },
      {
        "q": "How is the 51230 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 30 encodes the 150 mm bore (bore code x 5). The 215 mm OD and 50 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51230 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51230?",
        "a": "At the 900 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51230?",
        "a": "The 150/215/50 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 227 kN / C0a 720 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51230-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51230",
      "51230"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51330",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51330",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 150,
    "D_mm": 250,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 360,
    "static_load_kN": 1130,
    "fatigue_load_limit_kN": 36,
    "limiting_speed_rpm": 660,
    "max_rpm": 660,
    "speed_oil_rpm": 940,
    "weight_g": 16100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51330 belongs to the heavy-section 51300 thrust family of single-direction thrust ball bearings: 150 / 250 / 80 mm (shaft bore / OD / height). NTN builds the number from 513 is the dimension series (heavy-section 51300 thrust family); 30 encodes the 150 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 360 kN rating assumes the load arrives truly axial. If the duty is high speed with light thrust, check the minimum axial load formula first; a too-large thrust ball bearing fails by skid long before its Ca of 360 kN is ever approached. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "For a 150 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 513 heavy section buys capacity with a larger 250 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 360 kN never saves a bearing that is running too lightly loaded at 660 r/min.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51330 stack height of 80 mm and washer set differ from the double-direction execution.",
      "The Ca 360/C0a 1130 kN ratings and 36 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51330; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51330?",
        "a": "51330 is a single-direction thrust ball bearing to ISO 104: 150 mm shaft-washer bore, 250 mm outside diameter, 80 mm stack height (5.906 x 9.843 x 3.15 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 360 kN, C0a 1130 kN and a 36 kN fatigue load limit Pu; the grease limiting speed is 660 r/min and the oil rating 940 r/min; mass about 16100 g."
      },
      {
        "q": "How is the 51330 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 30 encodes the 150 mm bore (bore code x 5). The 250 mm OD and 80 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51330 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51330?",
        "a": "At the 660 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51330?",
        "a": "The 150/250/80 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 360 kN / C0a 1130 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51330-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 150×250×80 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51330",
      "51330"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51132",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51132",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 160,
    "D_mm": 200,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 112,
    "static_load_kN": 425,
    "fatigue_load_limit_kN": 14.4,
    "limiting_speed_rpm": 1200,
    "max_rpm": 1200,
    "speed_oil_rpm": 1700,
    "weight_g": 2100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51132 is an NTN single-direction thrust ball bearing of the light-section 51100 thrust family: 160 mm bore, 200 mm outside diameter, 31 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. Decoding 51132: 511 is the dimension series (light-section 51100 thrust family), with 32 encodes the 160 mm bore (bore code x 5). The static margin, C0a 425 kN against Ca 112 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. Size selection ends with the minimum-load check: at the 1,200 r/min class speed, the balls need a defined axial preload to keep rolling instead of skidding. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "For a 160 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 160 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 112 kN never saves a bearing that is running too lightly loaded at 1,200 r/min.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51132 has no radial capacity at all.",
      "Shock thrust above C0a 425 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 112/C0a 425 kN ratings and 14.4 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51132; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51132?",
        "a": "51132 is a single-direction thrust ball bearing to ISO 104: 160 mm shaft-washer bore, 200 mm outside diameter, 31 mm stack height (6.299 x 7.874 x 1.22 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 112 kN, C0a 425 kN and a 14.4 kN fatigue load limit Pu; the grease limiting speed is 1,200 r/min and the oil rating 1,700 r/min; mass about 2100 g."
      },
      {
        "q": "How is the 51132 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 32 encodes the 160 mm bore (bore code x 5). The 200 mm OD and 31 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51132 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51132?",
        "a": "At the 1,200 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51132?",
        "a": "The 160/200/31 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 112 kN / C0a 425 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51132-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51132",
      "51132"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51232",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51232",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 160,
    "D_mm": 225,
    "B_mm": 51,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 223,
    "static_load_kN": 720,
    "fatigue_load_limit_kN": 23.3,
    "limiting_speed_rpm": 870,
    "max_rpm": 870,
    "speed_oil_rpm": 1200,
    "weight_g": 6320,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51232 belongs to the medium-section 51200 thrust family of single-direction thrust ball bearings: 160 / 225 / 51 mm (shaft bore / OD / height). Two fields make up the code — 512 is the dimension series (medium-section 51200 thrust family) and 32 encodes the 160 mm bore (bore code x 5). Catalogue axial dynamic rating Ca is 223 kN against C0a 720 kN — a static/dynamic ratio of 3.23 that is the signature of a thrust raceway. Choose the medium-section 51200 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "For a 160 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 160 mm bore.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51232 has no radial capacity at all.",
      "Swapping the shaft and housing washers is an easy assembly error on the 160 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Swapping the shaft and housing washers is an easy assembly error on the 160 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The Ca 223/C0a 720 kN ratings and 23.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51232; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51232?",
        "a": "51232 is a single-direction thrust ball bearing to ISO 104: 160 mm shaft-washer bore, 225 mm outside diameter, 51 mm stack height (6.299 x 8.858 x 2.008 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 223 kN, C0a 720 kN and a 23.3 kN fatigue load limit Pu; the grease limiting speed is 870 r/min and the oil rating 1,200 r/min; mass about 6320 g."
      },
      {
        "q": "How is the 51232 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 32 encodes the 160 mm bore (bore code x 5). The 225 mm OD and 51 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51232 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51232?",
        "a": "At the 870 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51232?",
        "a": "The 160/225/51 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 223 kN / C0a 720 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51232-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 160×225×51 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51232",
      "51232"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51332",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51332",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 160,
    "D_mm": 270,
    "B_mm": 87,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 450,
    "static_load_kN": 1470,
    "fatigue_load_limit_kN": 45,
    "limiting_speed_rpm": 600,
    "max_rpm": 600,
    "speed_oil_rpm": 860,
    "weight_g": 20700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 160 x 270 x 87 mm, NTN 51332 sits in the heavy-section 51300 thrust family of the single-direction thrust programme. Reading the code: 513 is the dimension series (heavy-section 51300 thrust family), and 32 encodes the 160 mm bore (bore code x 5). At 87 mm of height the stack is compact for the 160 mm bore class, trading section height for the heavy-section load level. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 1470 kN class figures at the cost of OD and height. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 160 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 513 heavy section buys capacity with a larger 270 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Single-direction means exactly that: thrust on 51332 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 450 kN never saves a bearing that is running too lightly loaded at 600 r/min.",
      "The Ca 450/C0a 1470 kN ratings and 45 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51332; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51332?",
        "a": "51332 is a single-direction thrust ball bearing to ISO 104: 160 mm shaft-washer bore, 270 mm outside diameter, 87 mm stack height (6.299 x 10.63 x 3.425 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 450 kN, C0a 1470 kN and a 45 kN fatigue load limit Pu; the grease limiting speed is 600 r/min and the oil rating 860 r/min; mass about 20700 g."
      },
      {
        "q": "How is the 51332 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 32 encodes the 160 mm bore (bore code x 5). The 270 mm OD and 87 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51332 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51332?",
        "a": "At the 600 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51332?",
        "a": "The 160/270/87 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 450 kN / C0a 1470 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51332-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 160×270×87 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51332",
      "51332"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51134",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51134",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 170,
    "D_mm": 215,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 134,
    "static_load_kN": 510,
    "fatigue_load_limit_kN": 16.7,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "speed_oil_rpm": 1600,
    "weight_g": 2770,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51134 belongs to the light-section 51100 thrust family of single-direction thrust ball bearings: 170 / 215 / 34 mm (shaft bore / OD / height). The designation is 511 is the dimension series (light-section 51100 thrust family) plus 34 encodes the 170 mm bore (bore code x 5). The ball-and-cage set is separable from both washers, which is why the mounting order (shaft washer first, then cage, then housing washer) matters. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 170 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 170 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Swapping the shaft and housing washers is an easy assembly error on the 170 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51134 has no radial capacity at all.",
      "The Ca 134/C0a 510 kN ratings and 16.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51134; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51134?",
        "a": "51134 is a single-direction thrust ball bearing to ISO 104: 170 mm shaft-washer bore, 215 mm outside diameter, 34 mm stack height (6.693 x 8.465 x 1.339 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 134 kN, C0a 510 kN and a 16.7 kN fatigue load limit Pu; the grease limiting speed is 1,100 r/min and the oil rating 1,600 r/min; mass about 2770 g."
      },
      {
        "q": "How is the 51134 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 34 encodes the 170 mm bore (bore code x 5). The 215 mm OD and 34 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51134 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51134?",
        "a": "At the 1,100 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51134?",
        "a": "The 170/215/34 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 134 kN / C0a 510 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51134-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51134",
      "51134"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51234",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51234",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 170,
    "D_mm": 240,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 261,
    "static_load_kN": 835,
    "fatigue_load_limit_kN": 26.3,
    "limiting_speed_rpm": 810,
    "max_rpm": 810,
    "speed_oil_rpm": 1200,
    "weight_g": 7810,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 170 x 240 x 55 mm, NTN 51234 sits in the medium-section 51200 thrust family of the single-direction thrust programme. NTN builds the number from 512 is the dimension series (medium-section 51200 thrust family); 34 encodes the 170 mm bore (bore code x 5). NTN prints 261 kN axial dynamic and 835 kN axial static for this size and a 26.3 kN fatigue load limit Pu. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51234 cannot. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "For a 170 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 170 mm bore.",
      "The C0a of 835 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The C0a of 835 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The Ca 261/C0a 835 kN ratings and 26.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51234; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51234?",
        "a": "51234 is a single-direction thrust ball bearing to ISO 104: 170 mm shaft-washer bore, 240 mm outside diameter, 55 mm stack height (6.693 x 9.449 x 2.165 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 261 kN, C0a 835 kN and a 26.3 kN fatigue load limit Pu; the grease limiting speed is 810 r/min and the oil rating 1,200 r/min; mass about 7810 g."
      },
      {
        "q": "How is the 51234 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 34 encodes the 170 mm bore (bore code x 5). The 240 mm OD and 55 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51234 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51234?",
        "a": "At the 810 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51234?",
        "a": "The 170/240/55 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 261 kN / C0a 835 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51234-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 170×240×55 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51234",
      "51234"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51334",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51334",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 170,
    "D_mm": 280,
    "B_mm": 87,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 465,
    "static_load_kN": 1570,
    "fatigue_load_limit_kN": 47.5,
    "limiting_speed_rpm": 590,
    "max_rpm": 590,
    "speed_oil_rpm": 840,
    "weight_g": 21600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the heavy-section 51300 thrust family, 51334 measures 170 mm through the shaft washer, 280 mm over the outside and 87 mm in assembled height. Decoding 51334: 513 is the dimension series (heavy-section 51300 thrust family), with 34 encodes the 170 mm bore (bore code x 5). The washer section here is 55.0 mm of radial height, and the catalogue couples it with Ca 465 kN / C0a 1570 kN. Choose the heavy-section 51300 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "For a 170 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 513 heavy section buys capacity with a larger 280 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The C0a of 1570 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The Ca 465/C0a 1570 kN ratings and 47.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51334; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51334?",
        "a": "51334 is a single-direction thrust ball bearing to ISO 104: 170 mm shaft-washer bore, 280 mm outside diameter, 87 mm stack height (6.693 x 11.024 x 3.425 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 465 kN, C0a 1570 kN and a 47.5 kN fatigue load limit Pu; the grease limiting speed is 590 r/min and the oil rating 840 r/min; mass about 21600 g."
      },
      {
        "q": "How is the 51334 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 34 encodes the 170 mm bore (bore code x 5). The 280 mm OD and 87 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51334 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51334?",
        "a": "At the 590 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51334?",
        "a": "The 170/280/87 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 465 kN / C0a 1570 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51334-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 170×280×87 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51334",
      "51334"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51136",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51136",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 180,
    "D_mm": 225,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 135,
    "static_load_kN": 525,
    "fatigue_load_limit_kN": 16.7,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "speed_oil_rpm": 1500,
    "weight_g": 2920,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 180 x 225 x 34 mm, NTN 51136 sits in the light-section 51100 thrust family of the single-direction thrust programme. Two fields make up the code — 511 is the dimension series (light-section 51100 thrust family) and 36 encodes the 180 mm bore (bore code x 5). With Ca 135 kN and C0a 525 kN, each mm of shaft bore carries about 0.75 kN of dynamic axial rating. The 180/225/34 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "For a 180 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 180 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51136 stack height of 34 mm and washer set differ from the double-direction execution.",
      "The C0a of 525 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 135/C0a 525 kN ratings and 16.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51136; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51136?",
        "a": "51136 is a single-direction thrust ball bearing to ISO 104: 180 mm shaft-washer bore, 225 mm outside diameter, 34 mm stack height (7.087 x 8.858 x 1.339 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 135 kN, C0a 525 kN and a 16.7 kN fatigue load limit Pu; the grease limiting speed is 1,100 r/min and the oil rating 1,500 r/min; mass about 2920 g."
      },
      {
        "q": "How is the 51136 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 36 encodes the 180 mm bore (bore code x 5). The 225 mm OD and 34 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51136 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51136?",
        "a": "At the 1,100 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51136?",
        "a": "The 180/225/34 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 135 kN / C0a 525 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51136-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51136",
      "51136"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51236",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51236",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 180,
    "D_mm": 250,
    "B_mm": 56,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 266,
    "static_load_kN": 875,
    "fatigue_load_limit_kN": 26.9,
    "limiting_speed_rpm": 780,
    "max_rpm": 780,
    "speed_oil_rpm": 1100,
    "weight_g": 8340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the medium-section 51200 thrust family, 51236 measures 180 mm through the shaft washer, 250 mm over the outside and 56 mm in assembled height. Reading the code: 512 is the dimension series (medium-section 51200 thrust family), and 36 encodes the 180 mm bore (bore code x 5). The static margin, C0a 875 kN against Ca 266 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. Against a thrust roller bearing of the same 180 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 250 mm OD already tilts the raceway and concentrates the 875 kN static capacity on a few balls. ",
    "applications": [
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 180 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 180 mm bore.",
      "Shock thrust above C0a 875 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Shock thrust above C0a 875 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 266/C0a 875 kN ratings and 26.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51236; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51236?",
        "a": "51236 is a single-direction thrust ball bearing to ISO 104: 180 mm shaft-washer bore, 250 mm outside diameter, 56 mm stack height (7.087 x 9.843 x 2.205 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 266 kN, C0a 875 kN and a 26.9 kN fatigue load limit Pu; the grease limiting speed is 780 r/min and the oil rating 1,100 r/min; mass about 8340 g."
      },
      {
        "q": "How is the 51236 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 36 encodes the 180 mm bore (bore code x 5). The 250 mm OD and 56 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51236 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51236?",
        "a": "At the 780 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51236?",
        "a": "The 180/250/56 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 266 kN / C0a 875 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51236-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 180×250×56 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51236",
      "51236"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51336",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51336",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 180,
    "D_mm": 300,
    "B_mm": 95,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 490,
    "static_load_kN": 1700,
    "fatigue_load_limit_kN": 49.5,
    "limiting_speed_rpm": 540,
    "max_rpm": 540,
    "speed_oil_rpm": 780,
    "weight_g": 27500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51336 appears as a heavy-section 51300 thrust family bearing with a 180 mm shaft washer, a 300 mm housing diameter and 95 mm of stack height. The designation is 513 is the dimension series (heavy-section 51300 thrust family) plus 36 encodes the 180 mm bore (bore code x 5). Catalogue mass is about 27500 g for the full washer-and-cage stack. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51336 cannot. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 300 mm OD already tilts the raceway and concentrates the 1700 kN static capacity on a few balls. ",
    "applications": [
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 180 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 513 heavy section buys capacity with a larger 300 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "The 540 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The 540 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The 540 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "The Ca 490/C0a 1700 kN ratings and 49.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51336; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51336?",
        "a": "51336 is a single-direction thrust ball bearing to ISO 104: 180 mm shaft-washer bore, 300 mm outside diameter, 95 mm stack height (7.087 x 11.811 x 3.74 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 490 kN, C0a 1700 kN and a 49.5 kN fatigue load limit Pu; the grease limiting speed is 540 r/min and the oil rating 780 r/min; mass about 27500 g."
      },
      {
        "q": "How is the 51336 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 36 encodes the 180 mm bore (bore code x 5). The 300 mm OD and 95 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51336 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51336?",
        "a": "At the 540 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51336?",
        "a": "The 180/300/95 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 490 kN / C0a 1700 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51336-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 180×300×95 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51336",
      "51336"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51138",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51138",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 190,
    "D_mm": 240,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 170,
    "static_load_kN": 655,
    "fatigue_load_limit_kN": 20.2,
    "limiting_speed_rpm": 980,
    "max_rpm": 980,
    "speed_oil_rpm": 1400,
    "weight_g": 3750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the light-section 51100 thrust family, 51138 measures 190 mm through the shaft washer, 240 mm over the outside and 37 mm in assembled height. NTN builds the number from 511 is the dimension series (light-section 51100 thrust family); 38 encodes the 190 mm bore (bore code x 5). On speed, the grease limiting speed is 980 r/min and the oil rating 1,400 r/min. For a 190 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "For a 190 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 190 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Swapping the shaft and housing washers is an easy assembly error on the 190 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "The Ca 170/C0a 655 kN ratings and 20.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51138; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51138?",
        "a": "51138 is a single-direction thrust ball bearing to ISO 104: 190 mm shaft-washer bore, 240 mm outside diameter, 37 mm stack height (7.48 x 9.449 x 1.457 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 170 kN, C0a 655 kN and a 20.2 kN fatigue load limit Pu; the grease limiting speed is 980 r/min and the oil rating 1,400 r/min; mass about 3750 g."
      },
      {
        "q": "How is the 51138 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 38 encodes the 190 mm bore (bore code x 5). The 240 mm OD and 37 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51138 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51138?",
        "a": "At the 980 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51138?",
        "a": "The 190/240/37 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 170 kN / C0a 655 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51138-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51138",
      "51138"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51238",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51238",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 190,
    "D_mm": 270,
    "B_mm": 62,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 310,
    "static_load_kN": 1060,
    "fatigue_load_limit_kN": 31.5,
    "limiting_speed_rpm": 710,
    "max_rpm": 710,
    "speed_oil_rpm": 1000,
    "weight_g": 11300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51238 appears as a medium-section 51200 thrust family bearing with a 190 mm shaft washer, a 270 mm housing diameter and 62 mm of stack height. Decoding 51238: 512 is the dimension series (medium-section 51200 thrust family), with 38 encodes the 190 mm bore (bore code x 5). The ball-and-cage set is separable from both washers, which is why the mounting order (shaft washer first, then cage, then housing washer) matters. Size selection ends with the minimum-load check: at the 710 r/min class speed, the balls need a defined axial preload to keep rolling instead of skidding. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "For a 190 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 190 mm bore.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 310 kN never saves a bearing that is running too lightly loaded at 710 r/min.",
      "Shock thrust above C0a 1060 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51238 has no radial capacity at all.",
      "The Ca 310/C0a 1060 kN ratings and 31.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51238; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51238?",
        "a": "51238 is a single-direction thrust ball bearing to ISO 104: 190 mm shaft-washer bore, 270 mm outside diameter, 62 mm stack height (7.48 x 10.63 x 2.441 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 310 kN, C0a 1060 kN and a 31.5 kN fatigue load limit Pu; the grease limiting speed is 710 r/min and the oil rating 1,000 r/min; mass about 11300 g."
      },
      {
        "q": "How is the 51238 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 38 encodes the 190 mm bore (bore code x 5). The 270 mm OD and 62 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51238 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51238?",
        "a": "At the 710 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51238?",
        "a": "The 190/270/62 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 310 kN / C0a 1060 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51238-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 190×270×62 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51238",
      "51238"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51338",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51338",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 190,
    "D_mm": 320,
    "B_mm": 105,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 545,
    "static_load_kN": 1950,
    "fatigue_load_limit_kN": 55,
    "limiting_speed_rpm": 500,
    "max_rpm": 500,
    "speed_oil_rpm": 710,
    "weight_g": 35000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The heavy-section 51300 thrust family entry 51338 stacks a shaft washer, ball-and-cage set and housing washer into 105 mm of height over a 190 mm bore. Two fields make up the code — 513 is the dimension series (heavy-section 51300 thrust family) and 38 encodes the 190 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. Against a thrust roller bearing of the same 190 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "For a 190 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 513 heavy section buys capacity with a larger 320 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51338 has no radial capacity at all.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51338 stack height of 105 mm and washer set differ from the double-direction execution.",
      "Single-direction means exactly that: thrust on 51338 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 545/C0a 1950 kN ratings and 55 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51338; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51338?",
        "a": "51338 is a single-direction thrust ball bearing to ISO 104: 190 mm shaft-washer bore, 320 mm outside diameter, 105 mm stack height (7.48 x 12.598 x 4.134 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 545 kN, C0a 1950 kN and a 55 kN fatigue load limit Pu; the grease limiting speed is 500 r/min and the oil rating 710 r/min; mass about 35000 g."
      },
      {
        "q": "How is the 51338 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 38 encodes the 190 mm bore (bore code x 5). The 320 mm OD and 105 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51338 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51338?",
        "a": "At the 500 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51338?",
        "a": "The 190/320/105 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 545 kN / C0a 1950 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51338-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 190×320×105 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51338",
      "51338"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51140",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51140",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 200,
    "D_mm": 250,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 172,
    "static_load_kN": 675,
    "fatigue_load_limit_kN": 20.4,
    "limiting_speed_rpm": 960,
    "max_rpm": 960,
    "speed_oil_rpm": 1400,
    "weight_g": 3920,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51140 appears as a light-section 51100 thrust family bearing with a 200 mm shaft washer, a 250 mm housing diameter and 37 mm of stack height. Decoding 51140: 511 is the dimension series (light-section 51100 thrust family), with 40 encodes the 200 mm bore (bore code x 5). The static margin, C0a 675 kN against Ca 172 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting"
    ],
    "pitfalls": [
      "For a 200 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 200 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Shock thrust above C0a 675 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Shock thrust above C0a 675 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 172/C0a 675 kN ratings and 20.4 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51140; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51140?",
        "a": "51140 is a single-direction thrust ball bearing to ISO 104: 200 mm shaft-washer bore, 250 mm outside diameter, 37 mm stack height (7.874 x 9.843 x 1.457 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 172 kN, C0a 675 kN and a 20.4 kN fatigue load limit Pu; the grease limiting speed is 960 r/min and the oil rating 1,400 r/min; mass about 3920 g."
      },
      {
        "q": "How is the 51140 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 40 encodes the 200 mm bore (bore code x 5). The 250 mm OD and 37 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51140 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51140?",
        "a": "At the 960 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51140?",
        "a": "The 200/250/37 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 172 kN / C0a 675 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51140-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51140",
      "51140"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51240",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51240",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 200,
    "D_mm": 280,
    "B_mm": 62,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 315,
    "static_load_kN": 1110,
    "fatigue_load_limit_kN": 32,
    "limiting_speed_rpm": 700,
    "max_rpm": 700,
    "speed_oil_rpm": 990,
    "weight_g": 11800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The medium-section 51200 thrust family entry 51240 stacks a shaft washer, ball-and-cage set and housing washer into 62 mm of height over a 200 mm bore. Two fields make up the code — 512 is the dimension series (medium-section 51200 thrust family) and 40 encodes the 200 mm bore (bore code x 5). Catalogue axial dynamic rating Ca is 315 kN against C0a 1110 kN — a static/dynamic ratio of 3.52 that is the signature of a thrust raceway. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51240 cannot. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 280 mm OD already tilts the raceway and concentrates the 1110 kN static capacity on a few balls. ",
    "applications": [
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "For a 200 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 200 mm bore.",
      "The C0a of 1110 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Single-direction means exactly that: thrust on 51240 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Swapping the shaft and housing washers is an easy assembly error on the 200 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The Ca 315/C0a 1110 kN ratings and 32 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51240; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51240?",
        "a": "51240 is a single-direction thrust ball bearing to ISO 104: 200 mm shaft-washer bore, 280 mm outside diameter, 62 mm stack height (7.874 x 11.024 x 2.441 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 315 kN, C0a 1110 kN and a 32 kN fatigue load limit Pu; the grease limiting speed is 700 r/min and the oil rating 990 r/min; mass about 11800 g."
      },
      {
        "q": "How is the 51240 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 40 encodes the 200 mm bore (bore code x 5). The 280 mm OD and 62 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51240 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51240?",
        "a": "At the 700 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51240?",
        "a": "The 200/280/62 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 315 kN / C0a 1110 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51240-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 200×280×62 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51240",
      "51240"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51340",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51340",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 200,
    "D_mm": 340,
    "B_mm": 110,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 595,
    "static_load_kN": 2220,
    "fatigue_load_limit_kN": 61,
    "limiting_speed_rpm": 470,
    "max_rpm": 470,
    "speed_oil_rpm": 670,
    "weight_g": 41800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51340 is the 200 mm member of NTN's heavy-section 51300 thrust family: 340 mm across the washers, 110 mm tall. Reading the code: 513 is the dimension series (heavy-section 51300 thrust family), and 40 encodes the 200 mm bore (bore code x 5). At 110 mm of height the stack is compact for the 200 mm bore class, trading section height for the heavy-section load level. Choose the heavy-section 51300 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 340 mm OD already tilts the raceway and concentrates the 2220 kN static capacity on a few balls. ",
    "applications": [
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 200 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 513 heavy section buys capacity with a larger 340 mm OD and taller stack — check the housing space before upgrading a 512 position to this series.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51340 has no radial capacity at all.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 595 kN never saves a bearing that is running too lightly loaded at 470 r/min.",
      "The Ca 595/C0a 2220 kN ratings and 61 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51340; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51340?",
        "a": "51340 is a single-direction thrust ball bearing to ISO 104: 200 mm shaft-washer bore, 340 mm outside diameter, 110 mm stack height (7.874 x 13.386 x 4.331 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 595 kN, C0a 2220 kN and a 61 kN fatigue load limit Pu; the grease limiting speed is 470 r/min and the oil rating 670 r/min; mass about 41800 g."
      },
      {
        "q": "How is the 51340 designation structured?",
        "a": "513 is the dimension series (heavy-section 51300 thrust family); 40 encodes the 200 mm bore (bore code x 5). The 340 mm OD and 110 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51340 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51340?",
        "a": "At the 470 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51340?",
        "a": "The 200/340/110 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 595 kN / C0a 2220 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51340-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 200×340×110 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51340",
      "51340"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51144",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51144",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 220,
    "D_mm": 270,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 177,
    "static_load_kN": 740,
    "fatigue_load_limit_kN": 21.3,
    "limiting_speed_rpm": 920,
    "max_rpm": 920,
    "speed_oil_rpm": 1300,
    "weight_g": 4270,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51144 is the 220 mm member of NTN's light-section 51100 thrust family: 270 mm across the washers, 37 mm tall. Two fields make up the code — 511 is the dimension series (light-section 51100 thrust family) and 44 encodes the 220 mm bore (bore code x 5). With Ca 177 kN and C0a 740 kN, each mm of shaft bore carries about 0.80 kN of dynamic axial rating. For a 220 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 270 mm OD already tilts the raceway and concentrates the 740 kN static capacity on a few balls. ",
    "applications": [
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "For a 220 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 220 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Swapping the shaft and housing washers is an easy assembly error on the 220 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 177 kN never saves a bearing that is running too lightly loaded at 920 r/min.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 177/C0a 740 kN ratings and 21.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51144; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51144?",
        "a": "51144 is a single-direction thrust ball bearing to ISO 104: 220 mm shaft-washer bore, 270 mm outside diameter, 37 mm stack height (8.661 x 10.63 x 1.457 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 177 kN, C0a 740 kN and a 21.3 kN fatigue load limit Pu; the grease limiting speed is 920 r/min and the oil rating 1,300 r/min; mass about 4270 g."
      },
      {
        "q": "How is the 51144 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 44 encodes the 220 mm bore (bore code x 5). The 270 mm OD and 37 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51144 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51144?",
        "a": "At the 920 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51144?",
        "a": "The 220/270/37 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 177 kN / C0a 740 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51144-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51144",
      "51144"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51244",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51244",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 220,
    "D_mm": 300,
    "B_mm": 63,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 325,
    "static_load_kN": 1210,
    "fatigue_load_limit_kN": 34,
    "limiting_speed_rpm": 660,
    "max_rpm": 660,
    "speed_oil_rpm": 950,
    "weight_g": 13000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51244 is an NTN single-direction thrust ball bearing of the medium-section 51200 thrust family: 220 mm bore, 300 mm outside diameter, 63 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. Reading the code: 512 is the dimension series (medium-section 51200 thrust family), and 44 encodes the 220 mm bore (bore code x 5). The static margin, C0a 1210 kN against Ca 325 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. Size selection ends with the minimum-load check: at the 660 r/min class speed, the balls need a defined axial preload to keep rolling instead of skidding. The shaft washer (bore 220 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 220 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 220 mm bore.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 325 kN never saves a bearing that is running too lightly loaded at 660 r/min.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Shock thrust above C0a 1210 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 325/C0a 1210 kN ratings and 34 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51244; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51244?",
        "a": "51244 is a single-direction thrust ball bearing to ISO 104: 220 mm shaft-washer bore, 300 mm outside diameter, 63 mm stack height (8.661 x 11.811 x 2.48 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 325 kN, C0a 1210 kN and a 34 kN fatigue load limit Pu; the grease limiting speed is 660 r/min and the oil rating 950 r/min; mass about 13000 g."
      },
      {
        "q": "How is the 51244 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 44 encodes the 220 mm bore (bore code x 5). The 300 mm OD and 63 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51244 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51244?",
        "a": "At the 660 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51244?",
        "a": "The 220/300/63 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 325 kN / C0a 1210 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51244-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 220×300×63 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51244",
      "51244"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51148",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51148",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 240,
    "D_mm": 300,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 228,
    "static_load_kN": 935,
    "fatigue_load_limit_kN": 25.6,
    "limiting_speed_rpm": 780,
    "max_rpm": 780,
    "speed_oil_rpm": 1100,
    "weight_g": 6870,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51148 belongs to the light-section 51100 thrust family of single-direction thrust ball bearings: 240 / 300 / 45 mm (shaft bore / OD / height). Reading the code: 511 is the dimension series (light-section 51100 thrust family), and 48 encodes the 240 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 228 kN rating assumes the load arrives truly axial. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 935 kN class figures at the cost of OD and height. The shaft washer (bore 240 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 240 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 240 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Single-direction means exactly that: thrust on 51148 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51148 stack height of 45 mm and washer set differ from the double-direction execution.",
      "The Ca 228/C0a 935 kN ratings and 25.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51148; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51148?",
        "a": "51148 is a single-direction thrust ball bearing to ISO 104: 240 mm shaft-washer bore, 300 mm outside diameter, 45 mm stack height (9.449 x 11.811 x 1.772 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 228 kN, C0a 935 kN and a 25.6 kN fatigue load limit Pu; the grease limiting speed is 780 r/min and the oil rating 1,100 r/min; mass about 6870 g."
      },
      {
        "q": "How is the 51148 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 48 encodes the 240 mm bore (bore code x 5). The 300 mm OD and 45 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51148 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51148?",
        "a": "At the 780 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51148?",
        "a": "The 240/300/45 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 228 kN / C0a 935 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51148-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 240×300×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51148",
      "51148"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51248",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51248",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 240,
    "D_mm": 340,
    "B_mm": 78,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 415,
    "static_load_kN": 1650,
    "fatigue_load_limit_kN": 44,
    "limiting_speed_rpm": 550,
    "max_rpm": 550,
    "speed_oil_rpm": 790,
    "weight_g": 22400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 240 x 340 x 78 mm, NTN 51248 sits in the medium-section 51200 thrust family of the single-direction thrust programme. The designation is 512 is the dimension series (medium-section 51200 thrust family) plus 48 encodes the 240 mm bore (bore code x 5). With Ca 415 kN and C0a 1650 kN, each mm of shaft bore carries about 1.73 kN of dynamic axial rating. The 240/340/78 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 240 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 240 mm bore.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51248 stack height of 78 mm and washer set differ from the double-direction execution.",
      "The 550 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 415/C0a 1650 kN ratings and 44 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51248; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51248?",
        "a": "51248 is a single-direction thrust ball bearing to ISO 104: 240 mm shaft-washer bore, 340 mm outside diameter, 78 mm stack height (9.449 x 13.386 x 3.071 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 415 kN, C0a 1650 kN and a 44 kN fatigue load limit Pu; the grease limiting speed is 550 r/min and the oil rating 790 r/min; mass about 22400 g."
      },
      {
        "q": "How is the 51248 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 48 encodes the 240 mm bore (bore code x 5). The 340 mm OD and 78 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51248 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51248?",
        "a": "At the 550 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51248?",
        "a": "The 240/340/78 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 415 kN / C0a 1650 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51248-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 240×340×78 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51248",
      "51248"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51152",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51152",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 260,
    "D_mm": 320,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 232,
    "static_load_kN": 990,
    "fatigue_load_limit_kN": 26.2,
    "limiting_speed_rpm": 750,
    "max_rpm": 750,
    "speed_oil_rpm": 1100,
    "weight_g": 7380,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the light-section 51100 thrust family, 51152 measures 260 mm through the shaft washer, 320 mm over the outside and 45 mm in assembled height. Two fields make up the code — 511 is the dimension series (light-section 51100 thrust family) and 52 encodes the 260 mm bore (bore code x 5). With Ca 232 kN and C0a 990 kN, each mm of shaft bore carries about 0.89 kN of dynamic axial rating. If the duty is high speed with light thrust, check the minimum axial load formula first; a too-large thrust ball bearing fails by skid long before its Ca of 232 kN is ever approached. The shaft washer (bore 260 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "For a 260 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 260 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51152 stack height of 45 mm and washer set differ from the double-direction execution.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 232/C0a 990 kN ratings and 26.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51152; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51152?",
        "a": "51152 is a single-direction thrust ball bearing to ISO 104: 260 mm shaft-washer bore, 320 mm outside diameter, 45 mm stack height (10.236 x 12.598 x 1.772 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 232 kN, C0a 990 kN and a 26.2 kN fatigue load limit Pu; the grease limiting speed is 750 r/min and the oil rating 1,100 r/min; mass about 7380 g."
      },
      {
        "q": "How is the 51152 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 52 encodes the 260 mm bore (bore code x 5). The 320 mm OD and 45 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51152 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51152?",
        "a": "At the 750 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51152?",
        "a": "The 260/320/45 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 232 kN / C0a 990 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51152-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51152",
      "51152"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51252",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51252",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 260,
    "D_mm": 360,
    "B_mm": 79,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 440,
    "static_load_kN": 1810,
    "fatigue_load_limit_kN": 46.5,
    "limiting_speed_rpm": 530,
    "max_rpm": 530,
    "speed_oil_rpm": 760,
    "weight_g": 24200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51252 appears as a medium-section 51200 thrust family bearing with a 260 mm shaft washer, a 360 mm housing diameter and 79 mm of stack height. Reading the code: 512 is the dimension series (medium-section 51200 thrust family), and 52 encodes the 260 mm bore (bore code x 5). The static margin, C0a 1810 kN against Ca 440 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 260 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 260 mm bore.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51252 has no radial capacity at all.",
      "Shock thrust above C0a 1810 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 440/C0a 1810 kN ratings and 46.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51252; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51252?",
        "a": "51252 is a single-direction thrust ball bearing to ISO 104: 260 mm shaft-washer bore, 360 mm outside diameter, 79 mm stack height (10.236 x 14.173 x 3.11 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 440 kN, C0a 1810 kN and a 46.5 kN fatigue load limit Pu; the grease limiting speed is 530 r/min and the oil rating 760 r/min; mass about 24200 g."
      },
      {
        "q": "How is the 51252 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 52 encodes the 260 mm bore (bore code x 5). The 360 mm OD and 79 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51252 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51252?",
        "a": "At the 530 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51252?",
        "a": "The 260/360/79 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 440 kN / C0a 1810 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51252-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 260×360×79 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51252",
      "51252"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51156",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51156",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 280,
    "D_mm": 350,
    "B_mm": 53,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 305,
    "static_load_kN": 1270,
    "fatigue_load_limit_kN": 32.5,
    "limiting_speed_rpm": 650,
    "max_rpm": 650,
    "speed_oil_rpm": 940,
    "weight_g": 11800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The light-section 51100 thrust family entry 51156 stacks a shaft washer, ball-and-cage set and housing washer into 53 mm of height over a 280 mm bore. Reading the code: 511 is the dimension series (light-section 51100 thrust family), and 56 encodes the 280 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 305 kN rating assumes the load arrives truly axial. Choose the light-section 51100 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 280 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 280 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Swapping the shaft and housing washers is an easy assembly error on the 280 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51156 stack height of 53 mm and washer set differ from the double-direction execution.",
      "The Ca 305/C0a 1270 kN ratings and 32.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51156; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51156?",
        "a": "51156 is a single-direction thrust ball bearing to ISO 104: 280 mm shaft-washer bore, 350 mm outside diameter, 53 mm stack height (11.024 x 13.78 x 2.087 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 305 kN, C0a 1270 kN and a 32.5 kN fatigue load limit Pu; the grease limiting speed is 650 r/min and the oil rating 940 r/min; mass about 11800 g."
      },
      {
        "q": "How is the 51156 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 56 encodes the 280 mm bore (bore code x 5). The 350 mm OD and 53 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51156 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51156?",
        "a": "At the 650 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51156?",
        "a": "The 280/350/53 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 305 kN / C0a 1270 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51156-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 280×350×53 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51156",
      "51156"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51256",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51256",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 280,
    "D_mm": 380,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 460,
    "static_load_kN": 1970,
    "fatigue_load_limit_kN": 49,
    "limiting_speed_rpm": 510,
    "max_rpm": 510,
    "speed_oil_rpm": 730,
    "weight_g": 26100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51256 is the 280 mm member of NTN's medium-section 51200 thrust family: 380 mm across the washers, 80 mm tall. The designation is 512 is the dimension series (medium-section 51200 thrust family) plus 56 encodes the 280 mm bore (bore code x 5). With Ca 460 kN and C0a 1970 kN, each mm of shaft bore carries about 1.64 kN of dynamic axial rating. For a 280 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 280 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 280 mm bore.",
      "Swapping the shaft and housing washers is an easy assembly error on the 280 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "The C0a of 1970 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 460/C0a 1970 kN ratings and 49 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51256; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51256?",
        "a": "51256 is a single-direction thrust ball bearing to ISO 104: 280 mm shaft-washer bore, 380 mm outside diameter, 80 mm stack height (11.024 x 14.961 x 3.15 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 460 kN, C0a 1970 kN and a 49 kN fatigue load limit Pu; the grease limiting speed is 510 r/min and the oil rating 730 r/min; mass about 26100 g."
      },
      {
        "q": "How is the 51256 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 56 encodes the 280 mm bore (bore code x 5). The 380 mm OD and 80 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51256 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51256?",
        "a": "At the 510 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51256?",
        "a": "The 280/380/80 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 460 kN / C0a 1970 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51256-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 280×380×80 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51256",
      "51256"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51160",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51160",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 300,
    "D_mm": 380,
    "B_mm": 62,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 355,
    "static_load_kN": 1560,
    "fatigue_load_limit_kN": 38,
    "limiting_speed_rpm": 580,
    "max_rpm": 580,
    "speed_oil_rpm": 820,
    "weight_g": 17200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51160 is an NTN single-direction thrust ball bearing of the light-section 51100 thrust family: 300 mm bore, 380 mm outside diameter, 62 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. Two fields make up the code — 511 is the dimension series (light-section 51100 thrust family) and 60 encodes the 300 mm bore (bore code x 5). Flat-seat washers make the bearing tolerant of simple housings but demand square faces: the whole 355 kN rating assumes the load arrives truly axial. For a 300 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges"
    ],
    "pitfalls": [
      "For a 300 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 300 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Single-direction means exactly that: thrust on 51160 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The 580 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51160 stack height of 62 mm and washer set differ from the double-direction execution.",
      "The Ca 355/C0a 1560 kN ratings and 38 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51160; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51160?",
        "a": "51160 is a single-direction thrust ball bearing to ISO 104: 300 mm shaft-washer bore, 380 mm outside diameter, 62 mm stack height (11.811 x 14.961 x 2.441 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 355 kN, C0a 1560 kN and a 38 kN fatigue load limit Pu; the grease limiting speed is 580 r/min and the oil rating 820 r/min; mass about 17200 g."
      },
      {
        "q": "How is the 51160 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 60 encodes the 300 mm bore (bore code x 5). The 380 mm OD and 62 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51160 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51160?",
        "a": "At the 580 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51160?",
        "a": "The 300/380/62 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 355 kN / C0a 1560 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51160-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 300×380×62 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51160",
      "51160"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51260",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51260",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 300,
    "D_mm": 420,
    "B_mm": 95,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 590,
    "static_load_kN": 2680,
    "fatigue_load_limit_kN": 63.5,
    "limiting_speed_rpm": 440,
    "max_rpm": 440,
    "speed_oil_rpm": 630,
    "weight_g": 40600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51260 belongs to the medium-section 51200 thrust family of single-direction thrust ball bearings: 300 / 420 / 95 mm (shaft bore / OD / height). Reading the code: 512 is the dimension series (medium-section 51200 thrust family), and 60 encodes the 300 mm bore (bore code x 5). The static margin, C0a 2680 kN against Ca 590 kN, is what carries slow oscillating or shock thrust without permanent raceway dents. The 300/420/95 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. The housing washer needs radial freedom in its seat so the bearing can centre itself; clamping it radially defeats the self-centring the loose fit is designed to give. ",
    "applications": [
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 300 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 512 medium section is the default choice: balanced height and capacity for general vertical-shaft duty at 300 mm bore.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51260 stack height of 95 mm and washer set differ from the double-direction execution.",
      "Shock thrust above C0a 2680 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Shock thrust above C0a 2680 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The Ca 590/C0a 2680 kN ratings and 63.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51260; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51260?",
        "a": "51260 is a single-direction thrust ball bearing to ISO 104: 300 mm shaft-washer bore, 420 mm outside diameter, 95 mm stack height (11.811 x 16.535 x 3.74 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 590 kN, C0a 2680 kN and a 63.5 kN fatigue load limit Pu; the grease limiting speed is 440 r/min and the oil rating 630 r/min; mass about 40600 g."
      },
      {
        "q": "How is the 51260 designation structured?",
        "a": "512 is the dimension series (medium-section 51200 thrust family); 60 encodes the 300 mm bore (bore code x 5). The 420 mm OD and 95 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51260 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51260?",
        "a": "At the 440 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51260?",
        "a": "The 300/420/95 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 590 kN / C0a 2680 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51260-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 300×420×95 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51260",
      "51260"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51164",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51164",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 320,
    "D_mm": 400,
    "B_mm": 63,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 365,
    "static_load_kN": 1660,
    "fatigue_load_limit_kN": 39.5,
    "limiting_speed_rpm": 550,
    "max_rpm": 550,
    "speed_oil_rpm": 790,
    "weight_g": 18400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 320 x 400 x 63 mm, NTN 51164 sits in the light-section 51100 thrust family of the single-direction thrust programme. Reading the code: 511 is the dimension series (light-section 51100 thrust family), and 64 encodes the 320 mm bore (bore code x 5). The washer section here is 40.0 mm of radial height, and the catalogue couples it with Ca 365 kN / C0a 1660 kN. Within the thrust-ball plan, 511 is the light section and 514 the heaviest for a given bore; moving up a series raises the C0a from 1660 kN class figures at the cost of OD and height. Mount the stack in order and confirm the shaft washer sits against its shoulder before loading: pressing through the balls brinells the raceway on the spot. ",
    "applications": [
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 320 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 320 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "The 550 r/min speed figure assumes the catalogue lubrication state; at high speed the limiting factor is often the minimum load, not the rating table.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51164 has no radial capacity at all.",
      "The C0a of 1660 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The Ca 365/C0a 1660 kN ratings and 39.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51164; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51164?",
        "a": "51164 is a single-direction thrust ball bearing to ISO 104: 320 mm shaft-washer bore, 400 mm outside diameter, 63 mm stack height (12.598 x 15.748 x 2.48 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 365 kN, C0a 1660 kN and a 39.5 kN fatigue load limit Pu; the grease limiting speed is 550 r/min and the oil rating 790 r/min; mass about 18400 g."
      },
      {
        "q": "How is the 51164 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 64 encodes the 320 mm bore (bore code x 5). The 400 mm OD and 63 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51164 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51164?",
        "a": "At the 550 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51164?",
        "a": "The 320/400/63 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 365 kN / C0a 1660 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51164-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 320×400×63 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51164",
      "51164"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51168",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51168",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 340,
    "D_mm": 420,
    "B_mm": 64,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 375,
    "static_load_kN": 1760,
    "fatigue_load_limit_kN": 40.5,
    "limiting_speed_rpm": 530,
    "max_rpm": 530,
    "speed_oil_rpm": 760,
    "weight_g": 19700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51168 appears as a light-section 51100 thrust family bearing with a 340 mm shaft washer, a 420 mm housing diameter and 64 mm of stack height. The designation is 511 is the dimension series (light-section 51100 thrust family) plus 68 encodes the 340 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51168 cannot. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 340 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 340 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "The C0a of 1760 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The C0a of 1760 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Single-direction means exactly that: thrust on 51168 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 375/C0a 1760 kN ratings and 40.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51168; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51168?",
        "a": "51168 is a single-direction thrust ball bearing to ISO 104: 340 mm shaft-washer bore, 420 mm outside diameter, 64 mm stack height (13.386 x 16.535 x 2.52 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 375 kN, C0a 1760 kN and a 40.5 kN fatigue load limit Pu; the grease limiting speed is 530 r/min and the oil rating 760 r/min; mass about 19700 g."
      },
      {
        "q": "How is the 51168 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 68 encodes the 340 mm bore (bore code x 5). The 420 mm OD and 64 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51168 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51168?",
        "a": "At the 530 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51168?",
        "a": "The 340/420/64 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 375 kN / C0a 1760 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51168-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 340×420×64 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51168",
      "51168"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51172",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51172",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 360,
    "D_mm": 440,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 380,
    "static_load_kN": 1860,
    "fatigue_load_limit_kN": 42,
    "limiting_speed_rpm": 510,
    "max_rpm": 510,
    "speed_oil_rpm": 730,
    "weight_g": 21100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51172 is the 360 mm member of NTN's light-section 51100 thrust family: 440 mm across the washers, 65 mm tall. Reading the code: 511 is the dimension series (light-section 51100 thrust family), and 72 encodes the 360 mm bore (bore code x 5). The washer section here is 40.0 mm of radial height, and the catalogue couples it with Ca 380 kN / C0a 1860 kN. Choose the light-section 51100 thrust family when the shaft carries pure thrust in one direction at moderate speed — vertical shafts are the textbook case. Preload or working clearance must guarantee the minimum axial load at the catalogue speed; a spring or dead-weight arrangement is the usual answer on high-speed vertical shafts. ",
    "applications": [
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 360 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 360 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 51172 has no radial capacity at all.",
      "Shock thrust above C0a 1860 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "The C0a of 1860 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The Ca 380/C0a 1860 kN ratings and 42 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51172; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51172?",
        "a": "51172 is a single-direction thrust ball bearing to ISO 104: 360 mm shaft-washer bore, 440 mm outside diameter, 65 mm stack height (14.173 x 17.323 x 2.559 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 380 kN, C0a 1860 kN and a 42 kN fatigue load limit Pu; the grease limiting speed is 510 r/min and the oil rating 730 r/min; mass about 21100 g."
      },
      {
        "q": "How is the 51172 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 72 encodes the 360 mm bore (bore code x 5). The 440 mm OD and 65 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51172 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51172?",
        "a": "At the 510 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51172?",
        "a": "The 360/440/65 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 380 kN / C0a 1860 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51172-F",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 360×440×65 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51172",
      "51172"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51176",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51176",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 380,
    "D_mm": 460,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 380,
    "static_load_kN": 1910,
    "fatigue_load_limit_kN": 42,
    "limiting_speed_rpm": 500,
    "max_rpm": 500,
    "speed_oil_rpm": 710,
    "weight_g": 22300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 51176 belongs to the light-section 51100 thrust family of single-direction thrust ball bearings: 380 / 460 / 65 mm (shaft bore / OD / height). The designation is 511 is the dimension series (light-section 51100 thrust family) plus 76 encodes the 380 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. Against a thrust roller bearing of the same 380 mm bore, this bearing is cheaper, quieter and happier at speed, but carries far less load per mm of section. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 380 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 380 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Shock thrust above C0a 1910 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 380 kN never saves a bearing that is running too lightly loaded at 500 r/min.",
      "Single-direction means exactly that: thrust on 51176 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 380/C0a 1910 kN ratings and 42 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51176; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51176?",
        "a": "51176 is a single-direction thrust ball bearing to ISO 104: 380 mm shaft-washer bore, 460 mm outside diameter, 65 mm stack height (14.961 x 18.11 x 2.559 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 380 kN, C0a 1910 kN and a 42 kN fatigue load limit Pu; the grease limiting speed is 500 r/min and the oil rating 710 r/min; mass about 22300 g."
      },
      {
        "q": "How is the 51176 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 76 encodes the 380 mm bore (bore code x 5). The 460 mm OD and 65 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51176 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51176?",
        "a": "At the 500 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51176?",
        "a": "The 380/460/65 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 380 kN / C0a 1910 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51176-F",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 380×460×65 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51176",
      "51176"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51180",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51180",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 400,
    "D_mm": 480,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 390,
    "static_load_kN": 2010,
    "fatigue_load_limit_kN": 43.5,
    "limiting_speed_rpm": 480,
    "max_rpm": 480,
    "speed_oil_rpm": 690,
    "weight_g": 23300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "From the light-section 51100 thrust family, 51180 measures 400 mm through the shaft washer, 480 mm over the outside and 65 mm in assembled height. Reading the code: 511 is the dimension series (light-section 51100 thrust family), and 80 encodes the 400 mm bore (bore code x 5). The washer section here is 40.0 mm of radial height, and the catalogue couples it with Ca 390 kN / C0a 2010 kN. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 51180 cannot. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 400 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 400 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "The C0a of 2010 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The C0a of 2010 kN is a static rating: sizing continuous working thrust from C0a alone overstates what the raceway survives.",
      "The Ca 390/C0a 2010 kN ratings and 43.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51180; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51180?",
        "a": "51180 is a single-direction thrust ball bearing to ISO 104: 400 mm shaft-washer bore, 480 mm outside diameter, 65 mm stack height (15.748 x 18.898 x 2.559 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 390 kN, C0a 2010 kN and a 43.5 kN fatigue load limit Pu; the grease limiting speed is 480 r/min and the oil rating 690 r/min; mass about 23300 g."
      },
      {
        "q": "How is the 51180 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 80 encodes the 400 mm bore (bore code x 5). The 480 mm OD and 65 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51180 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51180?",
        "a": "At the 480 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51180?",
        "a": "The 400/480/65 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 390 kN / C0a 2010 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51180-F",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 400×480×65 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51180",
      "51180"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51184",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51184",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 420,
    "D_mm": 500,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 395,
    "static_load_kN": 2110,
    "fatigue_load_limit_kN": 44.5,
    "limiting_speed_rpm": 470,
    "max_rpm": 470,
    "speed_oil_rpm": 670,
    "weight_g": 24400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The light-section 51100 thrust family entry 51184 stacks a shaft washer, ball-and-cage set and housing washer into 65 mm of height over a 420 mm bore. The designation is 511 is the dimension series (light-section 51100 thrust family) plus 84 encodes the 420 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. Size selection ends with the minimum-load check: at the 470 r/min class speed, the balls need a defined axial preload to keep rolling instead of skidding. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 500 mm OD already tilts the raceway and concentrates the 2110 kN static capacity on a few balls. ",
    "applications": [
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 420 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 420 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Below the minimum axial load the balls skid; the catalogue Ca of 395 kN never saves a bearing that is running too lightly loaded at 470 r/min.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51184 stack height of 65 mm and washer set differ from the double-direction execution.",
      "Single-direction means exactly that: thrust on 51184 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 395/C0a 2110 kN ratings and 44.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51184; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51184?",
        "a": "51184 is a single-direction thrust ball bearing to ISO 104: 420 mm shaft-washer bore, 500 mm outside diameter, 65 mm stack height (16.535 x 19.685 x 2.559 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 395 kN, C0a 2110 kN and a 44.5 kN fatigue load limit Pu; the grease limiting speed is 470 r/min and the oil rating 670 r/min; mass about 24400 g."
      },
      {
        "q": "How is the 51184 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 84 encodes the 420 mm bore (bore code x 5). The 500 mm OD and 65 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51184 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51184?",
        "a": "At the 470 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51184?",
        "a": "The 420/500/65 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 395 kN / C0a 2110 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51184-F",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 420×500×65 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51184",
      "51184"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51188",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51188",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 440,
    "D_mm": 540,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 515,
    "static_load_kN": 2850,
    "fatigue_load_limit_kN": 58,
    "limiting_speed_rpm": 400,
    "max_rpm": 400,
    "speed_oil_rpm": 580,
    "weight_g": 40000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51188 is an NTN single-direction thrust ball bearing of the light-section 51100 thrust family: 440 mm bore, 540 mm outside diameter, 80 mm overall height in NTN Ball and Roller Bearings CAT.No.2203E. NTN builds the number from 511 is the dimension series (light-section 51100 thrust family); 88 encodes the 440 mm bore (bore code x 5). NTN prints 515 kN axial dynamic and 2850 kN axial static for this size and a 58 kN fatigue load limit Pu. The 440/540/80 envelope follows ISO 104, so dimensional interchange holds between makers — raceway osculation and ratings do not automatically follow. The shaft washer (bore 440 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts",
      "heavy press and mill screwdown thrust seats"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "For a 440 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 440 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Never substitute a double-direction bearing drawing part-for-part: the single-direction 51188 stack height of 80 mm and washer set differ from the double-direction execution.",
      "Swapping the shaft and housing washers is an easy assembly error on the 440 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The Ca 515/C0a 2850 kN ratings and 58 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51188; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51188?",
        "a": "51188 is a single-direction thrust ball bearing to ISO 104: 440 mm shaft-washer bore, 540 mm outside diameter, 80 mm stack height (17.323 x 21.26 x 3.15 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 515 kN, C0a 2850 kN and a 58 kN fatigue load limit Pu; the grease limiting speed is 400 r/min and the oil rating 580 r/min; mass about 40000 g."
      },
      {
        "q": "How is the 51188 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 88 encodes the 440 mm bore (bore code x 5). The 540 mm OD and 80 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51188 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51188?",
        "a": "At the 400 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51188?",
        "a": "The 440/540/80 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 515 kN / C0a 2850 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51188-F",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 440×540×80 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51188",
      "51188"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51192",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51192",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 460,
    "D_mm": 560,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 525,
    "static_load_kN": 3000,
    "fatigue_load_limit_kN": 60,
    "limiting_speed_rpm": 390,
    "max_rpm": 390,
    "speed_oil_rpm": 560,
    "weight_g": 41600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 460 x 560 x 80 mm, NTN 51192 sits in the light-section 51100 thrust family of the single-direction thrust programme. The designation is 511 is the dimension series (light-section 51100 thrust family) plus 92 encodes the 460 mm bore (bore code x 5). Because the contact points run at 90 deg to the shaft, none of the rating is available for radial load — not even incidentally. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. The shaft washer (bore 460 mm, tight on the shaft) and the housing washer (slightly looser bore) are not interchangeable — check the catalogue bore codes before pressing anything on. ",
    "applications": [
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 460 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 460 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "A housing washer pressed tight in its seat cannot self-centre; the resulting eccentric running shows up as cage wear long before raceway fatigue.",
      "Single-direction means exactly that: thrust on 51192 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "The Ca 525/C0a 3000 kN ratings and 60 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51192; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51192?",
        "a": "51192 is a single-direction thrust ball bearing to ISO 104: 460 mm shaft-washer bore, 560 mm outside diameter, 80 mm stack height (18.11 x 22.047 x 3.15 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 525 kN, C0a 3000 kN and a 60 kN fatigue load limit Pu; the grease limiting speed is 390 r/min and the oil rating 560 r/min; mass about 41600 g."
      },
      {
        "q": "How is the 51192 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 92 encodes the 460 mm bore (bore code x 5). The 560 mm OD and 80 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51192 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51192?",
        "a": "At the 390 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51192?",
        "a": "The 460/560/80 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 525 kN / C0a 3000 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51192-F",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51192",
      "51192"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51196",
    "brand": "NTN",
    "manufacturer_designation": "NTN 51196",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 480,
    "D_mm": 580,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 525,
    "static_load_kN": 3100,
    "fatigue_load_limit_kN": 60.5,
    "limiting_speed_rpm": 380,
    "max_rpm": 380,
    "speed_oil_rpm": 550,
    "weight_g": 43300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 51196 appears as a light-section 51100 thrust family bearing with a 480 mm shaft washer, a 580 mm housing diameter and 80 mm of stack height. NTN builds the number from 511 is the dimension series (light-section 51100 thrust family); 96 encodes the 480 mm bore (bore code x 5). NTN prints 525 kN axial dynamic and 3100 kN axial static for this size and a 60.5 kN fatigue load limit Pu. For a 480 mm shaft with combined radial-plus-axial load, pair this bearing with a separate radial bearing — the thrust ball bearing must never be asked to carry the radial share. After assembly, rotate under light load and check torque and temperature rise — a thrust ball bearing mounted with the washers swapped runs, but fails fast. ",
    "applications": [
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track",
      "lubricant starvation scoring on the raceway track when grease is thrown outward by centrifugal effect and never replaced"
    ],
    "pitfalls": [
      "For a 480 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 480 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Swapping the shaft and housing washers is an easy assembly error on the 480 mm size — the bores differ only slightly, but the wrong pairing walks off-centre under load.",
      "Single-direction means exactly that: thrust on 51196 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The Ca 525/C0a 3100 kN ratings and 60.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 51196; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 51196?",
        "a": "51196 is a single-direction thrust ball bearing to ISO 104: 480 mm shaft-washer bore, 580 mm outside diameter, 80 mm stack height (18.898 x 22.835 x 3.15 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 525 kN, C0a 3100 kN and a 60.5 kN fatigue load limit Pu; the grease limiting speed is 380 r/min and the oil rating 550 r/min; mass about 43300 g."
      },
      {
        "q": "How is the 51196 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); 96 encodes the 480 mm bore (bore code x 5). The 580 mm OD and 80 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 51196 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 51196?",
        "a": "At the 380 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 51196?",
        "a": "The 480/580/80 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 525 kN / C0a 3100 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51196-F",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 480×580×80 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊51196",
      "51196"
    ],
    "locale_variants": {}
  },
  {
    "sku": "511-500",
    "brand": "NTN",
    "manufacturer_designation": "NTN 511/500",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 500,
    "D_mm": 600,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 575,
    "static_load_kN": 3400,
    "fatigue_load_limit_kN": 65.5,
    "limiting_speed_rpm": 370,
    "max_rpm": 370,
    "speed_oil_rpm": 540,
    "weight_g": 45000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "NTN 511/500 belongs to the light-section 51100 thrust family of single-direction thrust ball bearings: 500 / 600 / 80 mm (shaft bore / OD / height). The designation is 511 is the dimension series (light-section 51100 thrust family) plus the part after the slash is the bore itself — 500 mm — used because the size falls outside the bore-code plan. NTN prints 575 kN axial dynamic and 3400 kN axial static for this size and a 65.5 kN fatigue load limit Pu. Selection starts from the load direction: if thrust ever reverses, plan a second thrust bearing (or a double-direction execution) rather than relying on the unloaded raceway. On a vertical shaft, pack grease between the washers and plan a relubrication path — centrifugal effect drives grease outward and the track runs dry without it. ",
    "applications": [
      "heavy press and mill screwdown thrust seats",
      "crane slew-ring auxiliary thrust positions",
      "large mixer and reactor vertical shafts",
      "bulk-handler stacker/reclaimer thrust pivots"
    ],
    "failure_modes": [
      "cage pocket wear and ball skid polish after long running below the minimum axial load, the balls sliding instead of rolling on the washers",
      "fretting between shaft washer and shaft when the seat is cut loose — the washer creeps, the centre line shifts and the balls start running off-track",
      "early fatigue from thrust reversal hammering the unloaded raceway, because the bearing has no contact surfaces for the opposite direction",
      "cage breakage after repeated shock reversal banged the ball set against the pocket bridges",
      "contamination pitting from particles settling on the horizontal housing washer — the classic failure of vertical-shaft grease-lubricated seats"
    ],
    "pitfalls": [
      "For a 500 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 500 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Shock thrust above C0a 3400 kN leaves dents that later become fatigue origins — crane-hook and press applications need the static check, not just the life calculation.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "Do not reuse a thrust bearing to \"absorb\" shaft thermal growth — the bearing clamps axially, so growth must be handled on the radial-bearing side of the arrangement.",
      "The Ca 575/C0a 3400 kN ratings and 65.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 511/500; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 511/500?",
        "a": "511/500 is a single-direction thrust ball bearing to ISO 104: 500 mm shaft-washer bore, 600 mm outside diameter, 80 mm stack height (19.685 x 23.622 x 3.15 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 575 kN, C0a 3400 kN and a 65.5 kN fatigue load limit Pu; the grease limiting speed is 370 r/min and the oil rating 540 r/min; mass about 45000 g."
      },
      {
        "q": "How is the 511/500 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); the part after the slash is the bore itself — 500 mm — used because the size falls outside the bore-code plan. The 600 mm OD and 80 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 511/500 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 511/500?",
        "a": "At the 370 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 511/500?",
        "a": "The 500/600/80 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 575 kN / C0a 3400 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "511",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊511-500",
      "511-500"
    ],
    "locale_variants": {}
  },
  {
    "sku": "511-530",
    "brand": "NTN",
    "manufacturer_designation": "NTN 511/530",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 530,
    "D_mm": 640,
    "B_mm": 85,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 645,
    "static_load_kN": 4000,
    "fatigue_load_limit_kN": 74.5,
    "limiting_speed_rpm": 350,
    "max_rpm": 350,
    "speed_oil_rpm": 500,
    "weight_g": 55800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "At 530 x 640 x 85 mm, NTN 511/530 sits in the light-section 51100 thrust family of the single-direction thrust programme. Reading the code: 511 is the dimension series (light-section 51100 thrust family), and the part after the slash is the bore itself — 530 mm — used because the size falls outside the bore-code plan. With Ca 645 kN and C0a 4000 kN, each mm of shaft bore carries about 1.22 kN of dynamic axial rating. Where misalignment between shaft and housing seats is expected, the spherical-seat washer executions (listed separately in the catalogue) absorb what the flat-seat 511/530 cannot. Keep the support faces square: a housing face out of perpendicular by a few hundredths over the 640 mm OD already tilts the raceway and concentrates the 4000 kN static capacity on a few balls. ",
    "applications": [
      "bulk-handler stacker/reclaimer thrust pivots",
      "heavy rotary furnace and kiln thrust points",
      "vertical hydro and pump-turbine thrust supports",
      "large marine winch and windlass shafts"
    ],
    "failure_modes": [
      "ball and raceway smearing from gyroscopic spin when the bearing runs fast under too little axial load — the minimum-load rule exists exactly for this",
      "housing-washer rocking on an out-of-square support face, seen as uneven wear around the raceway circle and rising running torque",
      "rapid flaking after radial load was allowed onto the bearing — a single-direction thrust ball bearing carries axial load only",
      "washer face corrosion under long standstill in humid service, later printed into the raceway as evenly spaced pitting",
      "edge loading from a shaft washer mounted off-centre, cutting the contact ellipse short at one side of the track"
    ],
    "pitfalls": [
      "For a 530 mm bore thrust bearing, the seating surfaces and oil supply decide service life; at this size a field-improvised housing is the usual root cause behind \"premature\" failures.",
      "The 511 light section is the speed-friendly end of the thrust-ball plan — for the same 530 mm bore it gives up load to gain OD, height and limiting-speed headroom.",
      "Single-direction means exactly that: thrust on 511/530 in the wrong direction separates the washers and drops the ball set — if reversal is possible even during coast-down, engineer against it.",
      "Radial load is the silent killer here: a belt pull or gear force on the same shaft must land on a radial bearing, because 511/530 has no radial capacity at all.",
      "Grease in a horizontal-washer seat stays only if the housing is designed to hold it; open vertical arrangements need an oil bath or a grease-retaining cover.",
      "The Ca 645/C0a 4000 kN ratings and 74.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 511/530; raceway geometry legitimately differs between manufacturers, so re-verify ratings and washer identification before substituting another make."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 511/530?",
        "a": "511/530 is a single-direction thrust ball bearing to ISO 104: 530 mm shaft-washer bore, 640 mm outside diameter, 85 mm stack height (20.866 x 25.197 x 3.346 in). From NTN Ball and Roller Bearings CAT.No.2203E: axial Ca 645 kN, C0a 4000 kN and a 74.5 kN fatigue load limit Pu; the grease limiting speed is 350 r/min and the oil rating 500 r/min; mass about 55800 g."
      },
      {
        "q": "How is the 511/530 designation structured?",
        "a": "511 is the dimension series (light-section 51100 thrust family); the part after the slash is the bore itself — 530 mm — used because the size falls outside the bore-code plan. The 640 mm OD and 85 mm height follow the ISO 104 boundary plan for that series."
      },
      {
        "q": "Can 511/530 carry radial load or reversing thrust?",
        "a": "No. The raceways contact the balls at 90 deg to the shaft, so the rating is purely axial and single-direction. Radial load must be carried by a separate radial bearing, and reversing thrust needs a second thrust bearing or a double-direction execution."
      },
      {
        "q": "Why does NTN specify a minimum axial load for 511/530?",
        "a": "At the 350 r/min class speed, centrifugal and gyroscopic effects make an under-loaded ball set skid and smear instead of roll. The catalogue minimum-load formula gives the axial preload — from the machine weight, springs or a dead-weight — that keeps the contact rolling."
      },
      {
        "q": "What should be checked before substituting another make for 511/530?",
        "a": "The 530/640/85 mm envelope is ISO 104 interchangeable, but washer bore codes, raceway osculation and ratings are maker-specific. Re-verify Ca 645 kN / C0a 4000 kN, the speed figures and the shaft/housing washer identification against the donor catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "511",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=227",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "＊511-530",
      "511-530"
    ],
    "locale_variants": {}
  },
  {
    "sku": "BA-3",
    "brand": "SKF",
    "manufacturer_designation": "BA 3",
    "series": "BA-series",
    "type": "thrust_ball",
    "d_mm": 3,
    "D_mm": 8,
    "B_mm": 3.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 0.806,
    "static_load_kN": 0.72,
    "fatigue_load_limit_kN": 0.027,
    "reference_speed_rpm": 26000,
    "limiting_speed_rpm": 36000,
    "max_rpm": 36000,
    "weight_g": 1,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "BA 3 is SKF's BA-series miniature single-direction thrust ball bearing for a 3 mm shaft — the BA digits give bore in millimetres directly — supplied as a shaft washer, a housing washer and a stamped sheet-steel ball-cage assembly, 3×8×3.5 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. the BA prefix marks SKF miniature thrust ball bearings for shaft diameters below 10 mm — the digits give the bore in millimetres directly, so a BA 3 fits a 3 mm shaft rather than using the two-digit bore code. BA miniatures use the standard stamped sheet-steel ball-cage assembly: two pressed steel washers retain a small ball complement, and at these dimensions the cage and washers are handled as three loose parts. Envelope 3×8×3.5 mm (0.118×0.315×0.138 in), 2.5 mm radial section, C 0.806 kN, C0 0.72 kN, Pu 0.027 kN. reference speed 26,000 r/min (thermal) and limiting speed 36,000 r/min (mechanical), catalogue mass 1 g. Load balance: C0 0.72 kN against C 0.806 kN gives a 0.89 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 0.027 kN enters the adjusted-life check. Bore-to-OD planning: OD 8 over bore 3 is a 2.67× step for this size, and the 3.5 mm height gives a bore/height ratio of 0.86; use these ratios when the housing recess around the 3 mm shaft is the first constraint. Sizing arithmetic on the 3 mm bore: 0.806 kN C over the 2.5 mm radial section gives 0.3 kN per section millimetre, and the 3.5 mm stack height is 1.40× that section — proportions typical of a BA thrust section. Mass and section check: 1 g inside the 3×8×3.5 mm outline leaves a 2.5 mm radial section, and the 0.72 kN static rating is 0.89× the dynamic rating — plan static safety and minimum preload against those figures. Envelope economics: the 3.5 mm axial height over a 2.5 mm radial section yields 0.2 kN of dynamic capacity per height millimetre, and the bearing weighs 1 g for 0.806 kN C — about 1 g per rated kN. Miniature handling note: the three BA components — shaft washer, housing washer and ball-cage assembly — are supplied loose and separate on contact, so mount the unit inside its housing recess before the shaft is offered; a dropped BA set scatters washers and balls that are nearly impossible to sort by eye, and a washer fitted reversed cannot be seen from outside once the cover is on. Service note at 3 mm bore: never grease-pack a BA bearing — one tiny dot of instrument oil on the ball set is enough, since the 1 g assembly will hydroplane its own cage out of position inside a flooded 8 mm OD recess.",
    "applications": [
      "small vertical electric motors and fan thrust positions",
      "screw-jack and clamp spindles",
      "appliance and office-machine thrust collars"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "permanent loss of the tiny separable components during unconfined handling or a washer fitted reversed and never detected",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 3.00×10^-6; for BA 3 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 3 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "The BA 3 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 3 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "There is no 51xxx coded size below 10 mm bore: the BA range is the miniature entry point for pure axial location, and at 3 mm the limit loads are small enough that shaft and housing squareness, not capacity, usually governs the design.",
      "Ordering discipline for BA 3: the catalogue page quotes BA 3 and its 0.806/0.72 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of BA-3?",
        "a": "BA 3 measures 3 mm bore × 8 mm OD × 3.5 mm bearing height (0.118 × 0.315 × 0.138 in), mass about 1 g. SKF 17000 ratings: C 0.806 kN, C0 0.72 kN, Pu 0.027 kN, reference speed 26,000 r/min (thermal) and limiting speed 36,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation BA 3 mean?",
        "a": "the BA prefix marks SKF miniature thrust ball bearings for shaft diameters below 10 mm — the digits give the bore in millimetres directly, so a BA 3 fits a 3 mm shaft rather than using the two-digit bore code. BA miniatures use the standard stamped sheet-steel ball-cage assembly: two pressed steel washers retain a small ball complement, and at these dimensions the cage and washers are handled as three loose parts. The BA range covers bores 3–9 mm; from 10 mm bore upwards the standard coded range begins at 51100."
      },
      {
        "q": "How are BA miniature thrust bearings supplied and fitted?",
        "a": "As three separable components — shaft washer, housing washer and ball-cage assembly. Build the set inside the housing recess before inserting the 3 mm shaft, keep the parts in their packaging until fitting, and note the tiny C 0.806 kN rating suits instrument and light axial location duty."
      },
      {
        "q": "Can BA-3 carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 3 mm shaft must go to a separate radial bearing; mixed loading through BA 3 edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "BA",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "BA-3",
      "BA 3"
    ],
    "locale_variants": {}
  },
  {
    "sku": "BA-4",
    "brand": "SKF",
    "manufacturer_designation": "BA 4",
    "series": "BA-series",
    "type": "thrust_ball",
    "d_mm": 4,
    "D_mm": 10,
    "B_mm": 4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 0.761,
    "static_load_kN": 0.72,
    "fatigue_load_limit_kN": 0.027,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 30000,
    "max_rpm": 30000,
    "weight_g": 2,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "SKF lists BA 4 in the BA miniature range: a single-direction thrust ball bearing of 4 mm bore (stated directly in the order number), 4×10×4 mm, built from two thin pressed washers and a miniature ball-cage assembly. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. the BA numbering convention is literal for miniature sizes — BA 4 names a 4 mm shaft outright, bridging the gap where the coded 51xxx range does not yet begin. cage-wise BA bearings follow the standard pressed sheet-steel design: the retainer separates the miniature ball complement and is handled as one of the three loose components. Envelope 4×10×4 mm (0.157×0.394×0.157 in), 3.0 mm radial section, C 0.761 kN, C0 0.72 kN, Pu 0.027 kN. reference speed 22,000 r/min (thermal) and limiting speed 30,000 r/min (mechanical), catalogue mass 2 g. Speed-ratio note for this exact unit: the reference speed is 22,000 r/min against a 30,000 r/min limiting speed, a reference-to-limit ratio of 0.73. Speed band width for this size is 8,000 r/min between reference and limiting (1.36× ratio); lubrication, preload and heat removal decide where inside that band BA 4 can actually run. Pitch-diameter arithmetic: dm = (4+10)/2 = 7.0 mm; at the 30,000 r/min limiting speed that corresponds to roughly 210k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Sizing arithmetic on the 4 mm bore: 0.761 kN C over the 3.0 mm radial section gives 0.3 kN per section millimetre, and the 4 mm stack height is 1.33× that section — proportions typical of a BA thrust section. Load balance: C0 0.72 kN against C 0.761 kN gives a 0.95 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 0.027 kN enters the adjusted-life check. Miniature handling note: the three BA components — shaft washer, housing washer and ball-cage assembly — are supplied loose and separate on contact, so mount the unit inside its housing recess before the shaft is offered; a dropped BA set scatters washers and balls that are nearly impossible to sort by eye, and a washer fitted reversed cannot be seen from outside once the cover is on. Service note at 4 mm bore: never grease-pack a BA bearing — one tiny dot of instrument oil on the ball set is enough, since the 2 g assembly will hydroplane its own cage out of position inside a flooded 10 mm OD recess.",
    "applications": [
      "small vertical electric motors and fan thrust positions",
      "light crane hooks and swivel pins",
      "instrument and indexing-table pivots"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "permanent loss of the tiny separable components during unconfined handling or a washer fitted reversed and never detected",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 3.00×10^-6; for BA 4 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The BA 4 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 4 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 4 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 4 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "There is no 51xxx coded size below 10 mm bore: the BA range is the miniature entry point for pure axial location, and at 4 mm the limit loads are small enough that shaft and housing squareness, not capacity, usually governs the design.",
      "Ordering discipline for BA 4: the catalogue page quotes BA 4 and its 0.761/0.72 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of BA-4?",
        "a": "The catalogue envelope is 4×10×4 mm, mass 2 g; ratings C 0.761 kN / C0 0.72 kN / Pu 0.027 kN, reference speed 22,000 r/min (thermal) and limiting speed 30,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation BA 4 mean?",
        "a": "the BA numbering convention is literal for miniature sizes — BA 4 names a 4 mm shaft outright, bridging the gap where the coded 51xxx range does not yet begin. cage-wise BA bearings follow the standard pressed sheet-steel design: the retainer separates the miniature ball complement and is handled as one of the three loose components. The BA range covers bores 3–9 mm; from 10 mm bore upwards the standard coded range begins at 51100."
      },
      {
        "q": "How is BA-4 lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 30,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "What do the two published speeds mean for BA-4?",
        "a": "The 22,000 r/min reference speed is the thermal balance under catalogue load; the 30,000 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "BA",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "BA-4",
      "BA 4"
    ],
    "locale_variants": {}
  },
  {
    "sku": "BA-5",
    "brand": "SKF",
    "manufacturer_designation": "BA 5",
    "series": "BA-series",
    "type": "thrust_ball",
    "d_mm": 5,
    "D_mm": 12,
    "B_mm": 4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 0.852,
    "static_load_kN": 0.965,
    "fatigue_load_limit_kN": 0.036,
    "reference_speed_rpm": 20000,
    "limiting_speed_rpm": 28000,
    "max_rpm": 28000,
    "weight_g": 2,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "For a 5 mm shaft, BA 5 is the BA miniature single-direction thrust ball bearing from SKF (bore spelled out in millimetres after BA): loose shaft washer, loose housing washer and a pressed steel ball-cage set, outline 5×12×4 mm. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. BA is SKF's miniature designation: below 10 mm bore the usual two-digit code is dropped and the number after BA spells the shaft diameter in millimetres, making BA 5 a 5 mm bearing. at BA size the ball-cage assembly is a tiny stamped sheet-steel retainer delivered loose with the two washers — there is no riveted or polymer-cage variant at this scale. Envelope 5×12×4 mm (0.197×0.472×0.157 in), 3.5 mm radial section, C 0.852 kN, C0 0.965 kN, Pu 0.036 kN. reference speed 20,000 r/min (thermal) and limiting speed 28,000 r/min (mechanical), catalogue mass 2 g. Speed-ratio note for this exact unit: the reference speed is 20,000 r/min against a 28,000 r/min limiting speed, a reference-to-limit ratio of 0.71. Bore-to-OD planning: OD 12 over bore 5 is a 2.40× step for this size, and the 4 mm height gives a bore/height ratio of 1.25; use these ratios when the housing recess around the 5 mm shaft is the first constraint. At the printed limiting speed of 28,000 r/min the mean pitch diameter dm ≈ 8.5 mm implies a dn value around 238k mm·r/min; the 20,000 r/min reference speed is the thermal-planning value under catalogue load. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 5.00×10^-6 at the 28,000 r/min limiting speed raises the required axial preload to about 0.28 N; the reference-speed value 0.14 N is the thermal design point. Imperial cross-check for procurement drawings: 0.197 in bore, 0.472 in OD, 0.157 in height, and the 2 g catalogue mass converts to 0.002 kg (0.1 oz). Miniature handling note: the three BA components — shaft washer, housing washer and ball-cage assembly — are supplied loose and separate on contact, so mount the unit inside its housing recess before the shaft is offered; a dropped BA set scatters washers and balls that are nearly impossible to sort by eye, and a washer fitted reversed cannot be seen from outside once the cover is on. For reference, the 5×12 mm outline occupies less than a pencil eraser yet still publishes C0 0.965 kN; select the housing recess before the screw length, because the 4 mm stack plus cover is often the tallest feature of a miniature axial stop.",
    "applications": [
      "appliance and office-machine thrust collars",
      "instrument and indexing-table pivots",
      "screw-jack and clamp spindles"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "permanent loss of the tiny separable components during unconfined handling or a washer fitted reversed and never detected",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 5.00×10^-6; for BA 5 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single BA 5 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 5 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat BA bearing.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "There is no 51xxx coded size below 10 mm bore: the BA range is the miniature entry point for pure axial location, and at 5 mm the limit loads are small enough that shaft and housing squareness, not capacity, usually governs the design.",
      "Ordering discipline for BA 5: the catalogue page quotes BA 5 and its 0.852/0.965 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of BA-5?",
        "a": "Boundary dimensions to ISO 104: bore 5 mm, OD 12 mm, height 4 mm; weight 2 g. Load figures from SKF 17000: dynamic 0.852 kN, static 0.965 kN, fatigue limit 0.036 kN; reference speed 20,000 r/min (thermal) and limiting speed 28,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation BA 5 mean?",
        "a": "BA is SKF's miniature designation: below 10 mm bore the usual two-digit code is dropped and the number after BA spells the shaft diameter in millimetres, making BA 5 a 5 mm bearing. at BA size the ball-cage assembly is a tiny stamped sheet-steel retainer delivered loose with the two washers — there is no riveted or polymer-cage variant at this scale. The BA range covers bores 3–9 mm; from 10 mm bore upwards the standard coded range begins at 51100."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "How is BA-5 lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 28,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "BA",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "BA-5",
      "BA 5"
    ],
    "locale_variants": {}
  },
  {
    "sku": "BA-6",
    "brand": "SKF",
    "manufacturer_designation": "BA 6",
    "series": "BA-series",
    "type": "thrust_ball",
    "d_mm": 6,
    "D_mm": 14,
    "B_mm": 5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 1.78,
    "static_load_kN": 1.92,
    "fatigue_load_limit_kN": 0.071,
    "reference_speed_rpm": 17000,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "weight_g": 4,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "For a 6 mm shaft, BA 6 is the BA miniature single-direction thrust ball bearing from SKF (bore spelled out in millimetres after BA): loose shaft washer, loose housing washer and a pressed steel ball-cage set, outline 6×14×5 mm. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. BA is SKF's miniature designation: below 10 mm bore the usual two-digit code is dropped and the number after BA spells the shaft diameter in millimetres, making BA 6 a 6 mm bearing. at BA size the ball-cage assembly is a tiny stamped sheet-steel retainer delivered loose with the two washers — there is no riveted or polymer-cage variant at this scale. Envelope 6×14×5 mm (0.236×0.551×0.197 in), 4.0 mm radial section, C 1.78 kN, C0 1.92 kN, Pu 0.071 kN. reference speed 17,000 r/min (thermal) and limiting speed 24,000 r/min (mechanical), catalogue mass 4 g. Selection figures for BA 6: the C0/C ratio is 1.08, Pu 0.071 kN is about 4 % of C, and the catalogue mass works out to roughly 1 g per millimetre of bore; the printed minimum-load factor is A 1.90×10^-5. Load balance: C0 1.92 kN against C 1.78 kN gives a 1.08 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 0.071 kN enters the adjusted-life check. Light-load floor: Pu = 0.071 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for BA 6; the number is 4 % of the 1.78 kN dynamic rating. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 1.90×10^-5 at the 24,000 r/min limiting speed raises the required axial preload to about 1.09 N; the reference-speed value 0.55 N is the thermal design point. Rating split for documentation: dynamic 1.78 kN (L10 life), static 1.92 kN (safety factor s0), fatigue limit 0.071 kN (adjusted life) — three different uses of three different numbers for BA 6, none interchangeable with another. Miniature handling note: the three BA components — shaft washer, housing washer and ball-cage assembly — are supplied loose and separate on contact, so mount the unit inside its housing recess before the shaft is offered; a dropped BA set scatters washers and balls that are nearly impossible to sort by eye, and a washer fitted reversed cannot be seen from outside once the cover is on. Service note at 6 mm bore: never grease-pack a BA bearing — one tiny dot of instrument oil on the ball set is enough, since the 4 g assembly will hydroplane its own cage out of position inside a flooded 14 mm OD recess.",
    "applications": [
      "screw-jack and clamp spindles",
      "small vertical electric motors and fan thrust positions",
      "light crane hooks and swivel pins"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "permanent loss of the tiny separable components during unconfined handling or a washer fitted reversed and never detected",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single BA 6 against two-way load lifts the loose washer off its raceway.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 1.78/1.92 kN and the available 14 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 1.78 kN track before first rotation.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 6 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "There is no 51xxx coded size below 10 mm bore: the BA range is the miniature entry point for pure axial location, and at 6 mm the limit loads are small enough that shaft and housing squareness, not capacity, usually governs the design.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for BA 6 as the miniature ba execution; other order numbers of the BA 6 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of BA-6?",
        "a": "Boundary dimensions to ISO 104: bore 6 mm, OD 14 mm, height 5 mm; weight 4 g. Load figures from SKF 17000: dynamic 1.78 kN, static 1.92 kN, fatigue limit 0.071 kN; reference speed 17,000 r/min (thermal) and limiting speed 24,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation BA 6 mean?",
        "a": "BA is SKF's miniature designation: below 10 mm bore the usual two-digit code is dropped and the number after BA spells the shaft diameter in millimetres, making BA 6 a 6 mm bearing. at BA size the ball-cage assembly is a tiny stamped sheet-steel retainer delivered loose with the two washers — there is no riveted or polymer-cage variant at this scale. The BA range covers bores 3–9 mm; from 10 mm bore upwards the standard coded range begins at 51100."
      },
      {
        "q": "What does BA mean in BA 6?",
        "a": "BA marks SKF miniature thrust ball bearings for bores below 10 mm; the digits are the bore in millimetres, so BA 3 fits a 3 mm shaft. The standard coded range starts at 51100 (10 mm bore)."
      },
      {
        "q": "How are BA miniature thrust bearings supplied and fitted?",
        "a": "As three separable components — shaft washer, housing washer and ball-cage assembly. Build the set inside the housing recess before inserting the 6 mm shaft, keep the parts in their packaging until fitting, and note the tiny C 1.78 kN rating suits instrument and light axial location duty."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "BA",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "BA-6",
      "BA 6"
    ],
    "locale_variants": {}
  },
  {
    "sku": "BA-7",
    "brand": "SKF",
    "manufacturer_designation": "BA 7",
    "series": "BA-series",
    "type": "thrust_ball",
    "d_mm": 7,
    "D_mm": 17,
    "B_mm": 6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 2.51,
    "static_load_kN": 2.9,
    "fatigue_load_limit_kN": 0.108,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "weight_g": 6,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "BA 7 is SKF's BA-series miniature single-direction thrust ball bearing for a 7 mm shaft — the BA digits give bore in millimetres directly — supplied as a shaft washer, a housing washer and a stamped sheet-steel ball-cage assembly, 7×17×6 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. the BA prefix marks SKF miniature thrust ball bearings for shaft diameters below 10 mm — the digits give the bore in millimetres directly, so a BA 7 fits a 7 mm shaft rather than using the two-digit bore code. BA miniatures use the standard stamped sheet-steel ball-cage assembly: two pressed steel washers retain a small ball complement, and at these dimensions the cage and washers are handled as three loose parts. Envelope 7×17×6 mm (0.276×0.669×0.236 in), 5.0 mm radial section, C 2.51 kN, C0 2.9 kN, Pu 0.108 kN. reference speed 14,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical), catalogue mass 6 g. Envelope economics: the 6 mm axial height over a 5.0 mm radial section yields 0.4 kN of dynamic capacity per height millimetre, and the bearing weighs 6 g for 2.51 kN C — about 2 g per rated kN. Section proportions: the 5.0 mm radial section compares with 7 mm of bore (section/bore ≈ 0.71) and the 6 mm height is 1.20× that section — the proportions that identify the BA envelope at a glance. Bore-to-OD planning: OD 17 over bore 7 is a 2.43× step for this size, and the 6 mm height gives a bore/height ratio of 1.17; use these ratios when the housing recess around the 7 mm shaft is the first constraint. Rating split for documentation: dynamic 2.51 kN (L10 life), static 2.9 kN (safety factor s0), fatigue limit 0.108 kN (adjusted life) — three different uses of three different numbers for BA 7, none interchangeable with another. Imperial cross-check for procurement drawings: 0.276 in bore, 0.669 in OD, 0.236 in height, and the 6 g catalogue mass converts to 0.006 kg (0.2 oz). Miniature handling note: the three BA components — shaft washer, housing washer and ball-cage assembly — are supplied loose and separate on contact, so mount the unit inside its housing recess before the shaft is offered; a dropped BA set scatters washers and balls that are nearly impossible to sort by eye, and a washer fitted reversed cannot be seen from outside once the cover is on. For reference, the 7×17 mm outline occupies less than a pencil eraser yet still publishes C0 2.9 kN; select the housing recess before the screw length, because the 6 mm stack plus cover is often the tallest feature of a miniature axial stop.",
    "applications": [
      "light crane hooks and swivel pins",
      "screw-jack and clamp spindles",
      "instrument and indexing-table pivots"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "permanent loss of the tiny separable components during unconfined handling or a washer fitted reversed and never detected",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 4.40×10^-5; for BA 7 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 7 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 2.51 kN track before first rotation.",
      "The BA 7 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 7 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "There is no 51xxx coded size below 10 mm bore: the BA range is the miniature entry point for pure axial location, and at 7 mm the limit loads are small enough that shaft and housing squareness, not capacity, usually governs the design.",
      "Ordering discipline for BA 7: the catalogue page quotes BA 7 and its 2.51/2.9 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of BA-7?",
        "a": "BA 7 measures 7 mm bore × 17 mm OD × 6 mm bearing height (0.276 × 0.669 × 0.236 in), mass about 6 g. SKF 17000 ratings: C 2.51 kN, C0 2.9 kN, Pu 0.108 kN, reference speed 14,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation BA 7 mean?",
        "a": "the BA prefix marks SKF miniature thrust ball bearings for shaft diameters below 10 mm — the digits give the bore in millimetres directly, so a BA 7 fits a 7 mm shaft rather than using the two-digit bore code. BA miniatures use the standard stamped sheet-steel ball-cage assembly: two pressed steel washers retain a small ball complement, and at these dimensions the cage and washers are handled as three loose parts. The BA range covers bores 3–9 mm; from 10 mm bore upwards the standard coded range begins at 51100."
      },
      {
        "q": "How are BA miniature thrust bearings supplied and fitted?",
        "a": "As three separable components — shaft washer, housing washer and ball-cage assembly. Build the set inside the housing recess before inserting the 7 mm shaft, keep the parts in their packaging until fitting, and note the tiny C 2.51 kN rating suits instrument and light axial location duty."
      },
      {
        "q": "Can BA-7 carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 7 mm shaft must go to a separate radial bearing; mixed loading through BA 7 edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "BA",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "BA-7",
      "BA 7"
    ],
    "locale_variants": {}
  },
  {
    "sku": "BA-8",
    "brand": "SKF",
    "manufacturer_designation": "BA 8",
    "series": "BA-series",
    "type": "thrust_ball",
    "d_mm": 8,
    "D_mm": 19,
    "B_mm": 7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 3.19,
    "static_load_kN": 3.8,
    "fatigue_load_limit_kN": 0.143,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 9,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "BA 8 is SKF's BA-series miniature single-direction thrust ball bearing for a 8 mm shaft — the BA digits give bore in millimetres directly — supplied as a shaft washer, a housing washer and a stamped sheet-steel ball-cage assembly, 8×19×7 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. the BA prefix marks SKF miniature thrust ball bearings for shaft diameters below 10 mm — the digits give the bore in millimetres directly, so a BA 8 fits a 8 mm shaft rather than using the two-digit bore code. BA miniatures use the standard stamped sheet-steel ball-cage assembly: two pressed steel washers retain a small ball complement, and at these dimensions the cage and washers are handled as three loose parts. Envelope 8×19×7 mm (0.315×0.748×0.276 in), 5.5 mm radial section, C 3.19 kN, C0 3.8 kN, Pu 0.143 kN. reference speed 12,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical), catalogue mass 9 g. Light-load floor: Pu = 0.143 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for BA 8; the number is 4 % of the 3.19 kN dynamic rating. Mass and section check: 9 g inside the 8×19×7 mm outline leaves a 5.5 mm radial section, and the 3.8 kN static rating is 1.19× the dynamic rating — plan static safety and minimum preload against those figures. Bore-to-OD planning: OD 19 over bore 8 is a 2.38× step for this size, and the 7 mm height gives a bore/height ratio of 1.14; use these ratios when the housing recess around the 8 mm shaft is the first constraint. Sizing arithmetic on the 8 mm bore: 3.19 kN C over the 5.5 mm radial section gives 0.6 kN per section millimetre, and the 7 mm stack height is 1.27× that section — proportions typical of a BA thrust section. Stack/annulus proportions: the 7 mm axial stack over the 233 mm² washer annulus gives 30.04 mm of height per annular square millimetre ×10⁻³, and at 9 g the bearing holds about 422.2 kN of C0 per kilogram. Miniature handling note: the three BA components — shaft washer, housing washer and ball-cage assembly — are supplied loose and separate on contact, so mount the unit inside its housing recess before the shaft is offered; a dropped BA set scatters washers and balls that are nearly impossible to sort by eye, and a washer fitted reversed cannot be seen from outside once the cover is on. For reference, the 8×19 mm outline occupies less than a pencil eraser yet still publishes C0 3.8 kN; select the housing recess before the screw length, because the 7 mm stack plus cover is often the tallest feature of a miniature axial stop.",
    "applications": [
      "appliance and office-machine thrust collars",
      "screw-jack and clamp spindles",
      "instrument and indexing-table pivots"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "permanent loss of the tiny separable components during unconfined handling or a washer fitted reversed and never detected",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The BA 8 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 8 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 3.19 kN track before first rotation.",
      "When the housing seat cannot be machined square to the 8 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat BA bearing.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 3.19/3.8 kN and the available 19 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "There is no 51xxx coded size below 10 mm bore: the BA range is the miniature entry point for pure axial location, and at 8 mm the limit loads are small enough that shaft and housing squareness, not capacity, usually governs the design.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for BA 8 as the miniature ba execution; other order numbers of the BA 8 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of BA-8?",
        "a": "BA 8 measures 8 mm bore × 19 mm OD × 7 mm bearing height (0.315 × 0.748 × 0.276 in), mass about 9 g. SKF 17000 ratings: C 3.19 kN, C0 3.8 kN, Pu 0.143 kN, reference speed 12,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation BA 8 mean?",
        "a": "the BA prefix marks SKF miniature thrust ball bearings for shaft diameters below 10 mm — the digits give the bore in millimetres directly, so a BA 8 fits a 8 mm shaft rather than using the two-digit bore code. BA miniatures use the standard stamped sheet-steel ball-cage assembly: two pressed steel washers retain a small ball complement, and at these dimensions the cage and washers are handled as three loose parts. The BA range covers bores 3–9 mm; from 10 mm bore upwards the standard coded range begins at 51100."
      },
      {
        "q": "Can a single BA 8 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "BA",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "BA-8",
      "BA 8"
    ],
    "locale_variants": {}
  },
  {
    "sku": "BA-9",
    "brand": "SKF",
    "manufacturer_designation": "BA 9",
    "series": "BA-series",
    "type": "thrust_ball",
    "d_mm": 9,
    "D_mm": 20,
    "B_mm": 7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 3.12,
    "static_load_kN": 3.8,
    "fatigue_load_limit_kN": 0.143,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "weight_g": 10,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "BA 9 is SKF's BA-series miniature single-direction thrust ball bearing for a 9 mm shaft — the BA digits give bore in millimetres directly — supplied as a shaft washer, a housing washer and a stamped sheet-steel ball-cage assembly, 9×20×7 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. the BA prefix marks SKF miniature thrust ball bearings for shaft diameters below 10 mm — the digits give the bore in millimetres directly, so a BA 9 fits a 9 mm shaft rather than using the two-digit bore code. BA miniatures use the standard stamped sheet-steel ball-cage assembly: two pressed steel washers retain a small ball complement, and at these dimensions the cage and washers are handled as three loose parts. Envelope 9×20×7 mm (0.354×0.787×0.276 in), 5.5 mm radial section, C 3.12 kN, C0 3.8 kN, Pu 0.143 kN. reference speed 12,000 r/min (thermal) and limiting speed 16,000 r/min (mechanical), catalogue mass 10 g. Capacity density: 3.12 kN C from 0.010 kg of bearing steel gives about 312.0 kN per kilogram; static density is correspondingly 380.0 kN/kg at C0 3.8 kN. Section proportions: the 5.5 mm radial section compares with 9 mm of bore (section/bore ≈ 0.61) and the 7 mm height is 1.27× that section — the proportions that identify the BA envelope at a glance. Speed band width for this size is 4,000 r/min between reference and limiting (1.33× ratio); lubrication, preload and heat removal decide where inside that band BA 9 can actually run. Sizing arithmetic on the 9 mm bore: 3.12 kN C over the 5.5 mm radial section gives 0.6 kN per section millimetre, and the 7 mm stack height is 1.27× that section — proportions typical of a BA thrust section. At the printed limiting speed of 16,000 r/min the mean pitch diameter dm ≈ 14.5 mm implies a dn value around 232k mm·r/min; the 12,000 r/min reference speed is the thermal-planning value under catalogue load. Miniature handling note: the three BA components — shaft washer, housing washer and ball-cage assembly — are supplied loose and separate on contact, so mount the unit inside its housing recess before the shaft is offered; a dropped BA set scatters washers and balls that are nearly impossible to sort by eye, and a washer fitted reversed cannot be seen from outside once the cover is on. Service note at 9 mm bore: never grease-pack a BA bearing — one tiny dot of instrument oil on the ball set is enough, since the 10 g assembly will hydroplane its own cage out of position inside a flooded 20 mm OD recess.",
    "applications": [
      "instrument and indexing-table pivots",
      "appliance and office-machine thrust collars",
      "screw-jack and clamp spindles"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "permanent loss of the tiny separable components during unconfined handling or a washer fitted reversed and never detected",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 7.50×10^-5; for BA 9 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 9 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 3.12/3.8 kN and the available 20 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "There is no 51xxx coded size below 10 mm bore: the BA range is the miniature entry point for pure axial location, and at 9 mm the limit loads are small enough that shaft and housing squareness, not capacity, usually governs the design.",
      "The 3.12/3.8 kN figures belong to BA 9 specifically (the miniature ba execution of BA 9); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of BA-9?",
        "a": "BA 9 measures 9 mm bore × 20 mm OD × 7 mm bearing height (0.354 × 0.787 × 0.276 in), mass about 10 g. SKF 17000 ratings: C 3.12 kN, C0 3.8 kN, Pu 0.143 kN, reference speed 12,000 r/min (thermal) and limiting speed 16,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation BA 9 mean?",
        "a": "the BA prefix marks SKF miniature thrust ball bearings for shaft diameters below 10 mm — the digits give the bore in millimetres directly, so a BA 9 fits a 9 mm shaft rather than using the two-digit bore code. BA miniatures use the standard stamped sheet-steel ball-cage assembly: two pressed steel washers retain a small ball complement, and at these dimensions the cage and washers are handled as three loose parts. The BA range covers bores 3–9 mm; from 10 mm bore upwards the standard coded range begins at 51100."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "How is BA-9 lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 16,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "BA",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "BA-9",
      "BA 9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51100-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51100",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 10,
    "D_mm": 24,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 9.95,
    "static_load_kN": 15.3,
    "fatigue_load_limit_kN": 0.56,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 20,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51100 is an ISO 104 single-direction thrust ball bearing, 10 mm bore and 24 mm OD on a flat housing seat, standing 9 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 00: bore 10 mm for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 10×24×9 mm (0.394×0.945×0.354 in), 7.0 mm radial section, C 9.95 kN, C0 15.3 kN, Pu 0.56 kN. reference speed 9,500 r/min (thermal) and limiting speed 13,000 r/min (mechanical), catalogue mass 20 g. Minimum-load arithmetic: with dm ≈ 17.0 mm and factor A 0.0012, Fam ≈ A·(n·dm/1000)² at the 9,500 r/min reference speed is about 31 N for 51100; below that preload the balls skid and smear the tracks. Speed-ratio note for this exact unit: the reference speed is 9,500 r/min against a 13,000 r/min limiting speed, a reference-to-limit ratio of 0.73. Stack/annulus proportions: the 9 mm axial stack over the 374 mm² washer annulus gives 24.06 mm of height per annular square millimetre ×10⁻³, and at 20 g the bearing holds about 765.0 kN of C0 per kilogram. Speed band width for this size is 3,500 r/min between reference and limiting (1.37× ratio); lubrication, preload and heat removal decide where inside that band 51100 can actually run. Imperial cross-check for procurement drawings: 0.394 in bore, 0.945 in OD, 0.354 in height, and the 20 g catalogue mass converts to 0.020 kg (0.7 oz). Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 9 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 9.95 kN C.",
    "applications": [
      "light crane hooks and swivel pins",
      "appliance and office-machine thrust collars",
      "small vertical electric motors and fan thrust positions"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.0012; for 51100 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 9.95 kN track before first rotation.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51100 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 10 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "Ordering discipline for 51100: the catalogue page quotes 51100 and its 9.95/15.3 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51100-SKF?",
        "a": "The catalogue envelope is 10×24×9 mm, mass 20 g; ratings C 9.95 kN / C0 15.3 kN / Pu 0.56 kN, reference speed 9,500 r/min (thermal) and limiting speed 13,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51100 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 00: bore 10 mm for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51100-SKF?",
        "a": "The 9,500 r/min reference speed is the thermal balance under catalogue load; the 13,000 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51100-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.0012 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51100",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51100-SKF",
      "51100"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51200-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51200",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 10,
    "D_mm": 26,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 18.6,
    "fatigue_load_limit_kN": 0.695,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 30,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51200 is a SKF single-direction thrust ball bearing for a 10 mm seat, built to ISO 104, with a flat housing seating surface, 10×26×11 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 00 decodes to 10 mm under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 10×26×11 mm (0.394×1.024×0.433 in), 8.0 mm radial section, C 12.7 kN, C0 18.6 kN, Pu 0.695 kN. reference speed 8,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 30 g. Light-load floor: Pu = 0.695 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51200; the number is 5 % of the 12.7 kN dynamic rating. Sizing arithmetic on the 10 mm bore: 12.7 kN C over the 8.0 mm radial section gives 1.6 kN per section millimetre, and the 11 mm stack height is 1.38× that section — proportions typical of a 51200 thrust section. Speed-ratio note for this exact unit: the reference speed is 8,000 r/min against a 11,000 r/min limiting speed, a reference-to-limit ratio of 0.73. Mass and section check: 30 g inside the 10×26×11 mm outline leaves a 8.0 mm radial section, and the 18.6 kN static rating is 1.46× the dynamic rating — plan static safety and minimum preload against those figures. Minimum-load arithmetic: with dm ≈ 18.0 mm and factor A 0.0018, Fam ≈ A·(n·dm/1000)² at the 8,000 r/min reference speed is about 37 N for 51200; below that preload the balls skid and smear the tracks. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 10 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 12.7/18.6 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "appliance and office-machine thrust collars",
      "screw-jack and clamp spindles",
      "instrument and indexing-table pivots"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 10 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.0018; for 51200 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 12.7/18.6 kN and the available 26 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 51200 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 10 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Ordering discipline for 51200: the catalogue page quotes 51200 and its 12.7/18.6 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51200-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 10 mm, OD 26 mm, height 11 mm; weight 30 g. Load figures from SKF 17000: dynamic 12.7 kN, static 18.6 kN, fatigue limit 0.695 kN; reference speed 8,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51200 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 00 decodes to 10 mm under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51200-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 11,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 10 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51200",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51200-SKF",
      "51200"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51101-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51101",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 12,
    "D_mm": 26,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 10.4,
    "static_load_kN": 16.6,
    "fatigue_load_limit_kN": 0.62,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 22,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51101 is SKF's 12 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 12×26×9 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 01 encode the bore as 12 mm, the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 12×26×9 mm (0.472×1.024×0.354 in), 7.0 mm radial section, C 10.4 kN, C0 16.6 kN, Pu 0.62 kN. reference speed 9,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical), catalogue mass 22 g. Mass and section check: 22 g inside the 12×26×9 mm outline leaves a 7.0 mm radial section, and the 16.6 kN static rating is 1.60× the dynamic rating — plan static safety and minimum preload against those figures. Stack/annulus proportions: the 9 mm axial stack over the 418 mm² washer annulus gives 21.53 mm of height per annular square millimetre ×10⁻³, and at 22 g the bearing holds about 754.5 kN of C0 per kilogram. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 13,000 r/min while thermal balance under catalogue load sets the 9,000 r/min reference; at dm ≈ 19.0 mm the corresponding dn is approximately 247k mm·r/min. Speed band width for this size is 4,000 r/min between reference and limiting (1.44× ratio); lubrication, preload and heat removal decide where inside that band 51101 can actually run. Light-load floor: Pu = 0.62 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51101; the number is 6 % of the 10.4 kN dynamic rating. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 12 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 10.4/16.6 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "small vertical electric motors and fan thrust positions",
      "light crane hooks and swivel pins",
      "appliance and office-machine thrust collars"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.0014; for 51101 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 9 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 10.4 kN track before first rotation.",
      "Ordering discipline for 51101: the catalogue page quotes 51101 and its 10.4/16.6 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51101-SKF?",
        "a": "51101 measures 12 mm bore × 26 mm OD × 9 mm bearing height (0.472 × 1.024 × 0.354 in), mass about 22 g. SKF 17000 ratings: C 10.4 kN, C0 16.6 kN, Pu 0.62 kN, reference speed 9,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51101 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 01 encode the bore as 12 mm, the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51101 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51101-SKF?",
        "a": "The 9,000 r/min reference speed is the thermal balance under catalogue load; the 13,000 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51101",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51101-SKF",
      "51101"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51201-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51201",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 12,
    "D_mm": 28,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 13.3,
    "static_load_kN": 20.8,
    "fatigue_load_limit_kN": 0.765,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 34,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51201 is SKF's 12 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 12×28×11 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 01 encode the bore as 12 mm, the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 12×28×11 mm (0.472×1.102×0.433 in), 8.0 mm radial section, C 13.3 kN, C0 20.8 kN, Pu 0.765 kN. reference speed 8,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 34 g. Minimum-load arithmetic: with dm ≈ 20.0 mm and factor A 0.0022, Fam ≈ A·(n·dm/1000)² at the 8,000 r/min reference speed is about 56 N for 51201; below that preload the balls skid and smear the tracks. Bore-to-OD planning: OD 28 over bore 12 is a 2.33× step for this size, and the 11 mm height gives a bore/height ratio of 1.09; use these ratios when the housing recess around the 12 mm shaft is the first constraint. Pitch-diameter arithmetic: dm = (12+28)/2 = 20.0 mm; at the 11,000 r/min limiting speed that corresponds to roughly 220k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Rating split for documentation: dynamic 13.3 kN (L10 life), static 20.8 kN (safety factor s0), fatigue limit 0.765 kN (adjusted life) — three different uses of three different numbers for 51201, none interchangeable with another. Envelope economics: the 11 mm axial height over a 8.0 mm radial section yields 1.2 kN of dynamic capacity per height millimetre, and the bearing weighs 34 g for 13.3 kN C — about 3 g per rated kN. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 11 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 13.3 kN C.",
    "applications": [
      "appliance and office-machine thrust collars",
      "light crane hooks and swivel pins",
      "instrument and indexing-table pivots"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51201 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 12 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 12 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51201 as the single flat pressed steel execution; other order numbers of the 51201 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51201-SKF?",
        "a": "51201 measures 12 mm bore × 28 mm OD × 11 mm bearing height (0.472 × 1.102 × 0.433 in), mass about 34 g. SKF 17000 ratings: C 13.3 kN, C0 20.8 kN, Pu 0.765 kN, reference speed 8,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51201 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 01 encode the bore as 12 mm, the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 12 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51201 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51201",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "53201",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 12×28×11 mm ISO 104 thrust-ball envelope with catalogue ratings within 10 %; 53201 is the single-direction, sphered housing washer with U 201 seat washer, stamped sheet-steel cage execution of this size — boundary dimensions interchangeable, execution differs. The counterpart is a sphered execution that needs its U 201 seat washer; its mounted H1 is taller than the bearing height."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51201-SKF",
      "51201"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51102-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51102",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 15,
    "D_mm": 28,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 10.6,
    "static_load_kN": 18.3,
    "fatigue_load_limit_kN": 0.67,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 23,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51102 is an ISO 104 single-direction thrust ball bearing, 15 mm bore and 28 mm OD on a flat housing seat, standing 9 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 02: bore 15 mm for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 15×28×9 mm (0.591×1.102×0.354 in), 6.5 mm radial section, C 10.6 kN, C0 18.3 kN, Pu 0.67 kN. reference speed 8,500 r/min (thermal) and limiting speed 12,000 r/min (mechanical), catalogue mass 23 g. Selection figures for 51102: the C0/C ratio is 1.73, Pu 0.67 kN is about 6 % of C, and the catalogue mass works out to roughly 2 g per millimetre of bore; the printed minimum-load factor is A 0.0017. Envelope economics: the 9 mm axial height over a 6.5 mm radial section yields 1.2 kN of dynamic capacity per height millimetre, and the bearing weighs 23 g for 10.6 kN C — about 2 g per rated kN. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51102 covers about 439 mm², distributing C0 18.3 kN over a mean track circle of π·dm ≈ 68 mm. Load balance: C0 18.3 kN against C 10.6 kN gives a 1.73 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 0.67 kN enters the adjusted-life check. Section proportions: the 6.5 mm radial section compares with 15 mm of bore (section/bore ≈ 0.43) and the 9 mm height is 1.38× that section — the proportions that identify the 51100 envelope at a glance. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 15 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 10.6/18.3 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "light crane hooks and swivel pins",
      "instrument and indexing-table pivots",
      "small vertical electric motors and fan thrust positions"
    ],
    "failure_modes": [
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 15 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51102 against two-way load lifts the loose washer off its raceway.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.0017; for 51102 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 10.6/18.3 kN figures belong to 51102 specifically (the single flat pressed steel execution of 51102); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51102-SKF?",
        "a": "The catalogue envelope is 15×28×9 mm, mass 23 g; ratings C 10.6 kN / C0 18.3 kN / Pu 0.67 kN, reference speed 8,500 r/min (thermal) and limiting speed 12,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51102 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 02: bore 15 mm for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 15 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51102 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51102",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51102-SKF",
      "51102"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51202-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51202",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 15,
    "D_mm": 32,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 15.9,
    "static_load_kN": 25,
    "fatigue_load_limit_kN": 0.915,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 46,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51202 is a SKF single-direction thrust ball bearing for a 15 mm seat, built to ISO 104, with a flat housing seating surface, 15×32×12 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 02 decodes to 15 mm under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 15×32×12 mm (0.591×1.26×0.472 in), 8.5 mm radial section, C 15.9 kN, C0 25 kN, Pu 0.915 kN. reference speed 7,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 46 g. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 10,000 r/min while thermal balance under catalogue load sets the 7,000 r/min reference; at dm ≈ 23.5 mm the corresponding dn is approximately 235k mm·r/min. Minimum-load arithmetic: with dm ≈ 23.5 mm and factor A 0.0038, Fam ≈ A·(n·dm/1000)² at the 7,000 r/min reference speed is about 103 N for 51202; below that preload the balls skid and smear the tracks. Speed band width for this size is 3,000 r/min between reference and limiting (1.43× ratio); lubrication, preload and heat removal decide where inside that band 51202 can actually run. Load balance: C0 25 kN against C 15.9 kN gives a 1.57 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 0.915 kN enters the adjusted-life check. Stack/annulus proportions: the 12 mm axial stack over the 628 mm² washer annulus gives 19.11 mm of height per annular square millimetre ×10⁻³, and at 46 g the bearing holds about 543.5 kN of C0 per kilogram. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 12 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 15.9 kN C.",
    "applications": [
      "screw-jack and clamp spindles",
      "instrument and indexing-table pivots",
      "light crane hooks and swivel pins"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 15 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "When the housing seat cannot be machined square to the 15 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.0038; for 51202 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 15.9/25 kN figures belong to 51202 specifically (the single flat pressed steel execution of 51202); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51202-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 15 mm, OD 32 mm, height 12 mm; weight 46 g. Load figures from SKF 17000: dynamic 15.9 kN, static 25 kN, fatigue limit 0.915 kN; reference speed 7,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51202 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 02 decodes to 15 mm under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51202 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51202-SKF?",
        "a": "The 7,000 r/min reference speed is the thermal balance under catalogue load; the 10,000 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51202",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51202-SKF",
      "51202"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51103-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51103",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 17,
    "D_mm": 30,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 11.4,
    "static_load_kN": 21.2,
    "fatigue_load_limit_kN": 0.78,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 25,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51103 is a SKF single-direction thrust ball bearing for a 17 mm seat, built to ISO 104, with a flat housing seating surface, 17×30×9 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 03 decodes to 17 mm under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 17×30×9 mm (0.669×1.181×0.354 in), 6.5 mm radial section, C 11.4 kN, C0 21.2 kN, Pu 0.78 kN. reference speed 8,500 r/min (thermal) and limiting speed 12,000 r/min (mechanical), catalogue mass 25 g. Section proportions: the 6.5 mm radial section compares with 17 mm of bore (section/bore ≈ 0.38) and the 9 mm height is 1.38× that section — the proportions that identify the 51100 envelope at a glance. Pitch-diameter arithmetic: dm = (17+30)/2 = 23.5 mm; at the 12,000 r/min limiting speed that corresponds to roughly 282k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Speed band width for this size is 3,500 r/min between reference and limiting (1.41× ratio); lubrication, preload and heat removal decide where inside that band 51103 can actually run. Rating split for documentation: dynamic 11.4 kN (L10 life), static 21.2 kN (safety factor s0), fatigue limit 0.78 kN (adjusted life) — three different uses of three different numbers for 51103, none interchangeable with another. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51103 covers about 480 mm², distributing C0 21.2 kN over a mean track circle of π·dm ≈ 74 mm. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 9 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 11.4 kN C.",
    "applications": [
      "screw-jack and clamp spindles",
      "light crane hooks and swivel pins",
      "instrument and indexing-table pivots"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 17 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 11.4/21.2 kN and the available 30 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "When the housing seat cannot be machined square to the 17 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 9 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The 11.4/21.2 kN figures belong to 51103 specifically (the single flat pressed steel execution of 51103); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51103-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 17 mm, OD 30 mm, height 9 mm; weight 25 g. Load figures from SKF 17000: dynamic 11.4 kN, static 21.2 kN, fatigue limit 0.78 kN; reference speed 8,500 r/min (thermal) and limiting speed 12,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51103 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 03 decodes to 17 mm under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51103-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 12,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 17 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51103",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×30×9 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51103-SKF",
      "51103"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51203-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51203",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 17,
    "D_mm": 35,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 16.3,
    "static_load_kN": 27,
    "fatigue_load_limit_kN": 1,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 53,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51203 is an ISO 104 single-direction thrust ball bearing, 17 mm bore and 35 mm OD on a flat housing seat, standing 12 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 03: bore 17 mm for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 17×35×12 mm (0.669×1.378×0.472 in), 9.0 mm radial section, C 16.3 kN, C0 27 kN, Pu 1 kN. reference speed 6,700 r/min (thermal) and limiting speed 9,500 r/min (mechanical), catalogue mass 53 g. Bore-to-OD planning: OD 35 over bore 17 is a 2.06× step for this size, and the 12 mm height gives a bore/height ratio of 1.42; use these ratios when the housing recess around the 17 mm shaft is the first constraint. At the printed limiting speed of 9,500 r/min the mean pitch diameter dm ≈ 26.0 mm implies a dn value around 247k mm·r/min; the 6,700 r/min reference speed is the thermal-planning value under catalogue load. Envelope economics: the 12 mm axial height over a 9.0 mm radial section yields 1.4 kN of dynamic capacity per height millimetre, and the bearing weighs 53 g for 16.3 kN C — about 3 g per rated kN. Speed band width for this size is 2,800 r/min between reference and limiting (1.42× ratio); lubrication, preload and heat removal decide where inside that band 51203 can actually run. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51203 covers about 735 mm², distributing C0 27 kN over a mean track circle of π·dm ≈ 82 mm. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 17 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 16.3/27 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "light crane hooks and swivel pins",
      "screw-jack and clamp spindles",
      "small vertical electric motors and fan thrust positions"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51203 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 17 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "The 51203 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 17 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 17 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51203 as the single flat pressed steel execution; other order numbers of the 51203 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51203-SKF?",
        "a": "The catalogue envelope is 17×35×12 mm, mass 53 g; ratings C 16.3 kN / C0 27 kN / Pu 1 kN, reference speed 6,700 r/min (thermal) and limiting speed 9,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51203 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 03: bore 17 mm for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51203-SKF?",
        "a": "The 6,700 r/min reference speed is the thermal balance under catalogue load; the 9,500 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51203-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.0047 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51203",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51203-SKF",
      "51203"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51104-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51104",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 20,
    "D_mm": 35,
    "B_mm": 10,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 15.1,
    "static_load_kN": 29,
    "fatigue_load_limit_kN": 1.08,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 37,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51104 is an ISO 104 single-direction thrust ball bearing, 20 mm bore and 35 mm OD on a flat housing seat, standing 10 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 04: bore 20 mm (code 04 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 20×35×10 mm (0.787×1.378×0.394 in), 7.5 mm radial section, C 15.1 kN, C0 29 kN, Pu 1.08 kN. reference speed 7,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 37 g. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 10,000 r/min while thermal balance under catalogue load sets the 7,500 r/min reference; at dm ≈ 27.5 mm the corresponding dn is approximately 275k mm·r/min. Section proportions: the 7.5 mm radial section compares with 20 mm of bore (section/bore ≈ 0.38) and the 10 mm height is 1.33× that section — the proportions that identify the 51100 envelope at a glance. Envelope economics: the 10 mm axial height over a 7.5 mm radial section yields 1.5 kN of dynamic capacity per height millimetre, and the bearing weighs 37 g for 15.1 kN C — about 2 g per rated kN. Light-load floor: Pu = 1.08 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51104; the number is 7 % of the 15.1 kN dynamic rating. Static-first selection data: 29 kN C0 spread across the 10 mm stack gives 2.9 kN of static rating per height millimetre, and the 37 g mass/C0 ratio is about 1 g per static kN — crane-hook and screw positions are normally sized on these two figures. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 20 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 15.1/29 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "screw-jack and clamp spindles",
      "small vertical electric motors and fan thrust positions",
      "light crane hooks and swivel pins"
    ],
    "failure_modes": [
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 15.1 kN track before first rotation.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 10 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51104 against two-way load lifts the loose washer off its raceway.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 15.1/29 kN and the available 35 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 15.1/29 kN figures belong to 51104 specifically (the single flat pressed steel execution of 51104); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51104-SKF?",
        "a": "The catalogue envelope is 20×35×10 mm, mass 37 g; ratings C 15.1 kN / C0 29 kN / Pu 1.08 kN, reference speed 7,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51104 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 04: bore 20 mm (code 04 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51104-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 10,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51104",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×35×10 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51104-SKF",
      "51104"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51204-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51204",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 20,
    "D_mm": 40,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 21.2,
    "static_load_kN": 37.5,
    "fatigue_load_limit_kN": 1.4,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 83,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51204 is a SKF single-direction thrust ball bearing for a 20 mm seat, built to ISO 104, with a flat housing seating surface, 20×40×14 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 04 decodes to 20 mm (code 04 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 20×40×14 mm (0.787×1.575×0.551 in), 10.0 mm radial section, C 21.2 kN, C0 37.5 kN, Pu 1.4 kN. reference speed 6,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical), catalogue mass 83 g. Mass and section check: 83 g inside the 20×40×14 mm outline leaves a 10.0 mm radial section, and the 37.5 kN static rating is 1.77× the dynamic rating — plan static safety and minimum preload against those figures. Speed band width for this size is 2,000 r/min between reference and limiting (1.33× ratio); lubrication, preload and heat removal decide where inside that band 51204 can actually run. At the printed limiting speed of 8,000 r/min the mean pitch diameter dm ≈ 30.0 mm implies a dn value around 240k mm·r/min; the 6,000 r/min reference speed is the thermal-planning value under catalogue load. Stack/annulus proportions: the 14 mm axial stack over the 942 mm² washer annulus gives 14.86 mm of height per annular square millimetre ×10⁻³, and at 83 g the bearing holds about 451.8 kN of C0 per kilogram. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 8,000 r/min while thermal balance under catalogue load sets the 6,000 r/min reference; at dm ≈ 30.0 mm the corresponding dn is approximately 240k mm·r/min. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 20 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 21.2/37.5 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "small vertical electric motors and fan thrust positions",
      "instrument and indexing-table pivots",
      "screw-jack and clamp spindles"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 20 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.0085; for 51204 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 21.2/37.5 kN and the available 40 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 51204 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 20 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Ordering discipline for 51204: the catalogue page quotes 51204 and its 21.2/37.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51204-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 20 mm, OD 40 mm, height 14 mm; weight 83 g. Load figures from SKF 17000: dynamic 21.2 kN, static 37.5 kN, fatigue limit 1.4 kN; reference speed 6,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51204 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 04 decodes to 20 mm (code 04 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51204-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.0085 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51204",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51204-SKF",
      "51204"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51105-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51105",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 42,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 18.2,
    "static_load_kN": 39,
    "fatigue_load_limit_kN": 1.43,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 56,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51105 is a SKF single-direction thrust ball bearing for a 25 mm seat, built to ISO 104, with a flat housing seating surface, 25×42×11 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 05 decodes to 25 mm (code 05 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 25×42×11 mm (0.984×1.654×0.433 in), 8.5 mm radial section, C 18.2 kN, C0 39 kN, Pu 1.43 kN. reference speed 6,300 r/min (thermal) and limiting speed 9,000 r/min (mechanical), catalogue mass 56 g. Mass and section check: 56 g inside the 25×42×11 mm outline leaves a 8.5 mm radial section, and the 39 kN static rating is 2.14× the dynamic rating — plan static safety and minimum preload against those figures. Light-load floor: Pu = 1.43 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51105; the number is 8 % of the 18.2 kN dynamic rating. Imperial cross-check for procurement drawings: 0.984 in bore, 1.654 in OD, 0.433 in height, and the 56 g catalogue mass converts to 0.056 kg (2.0 oz). Load balance: C0 39 kN against C 18.2 kN gives a 2.14 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 1.43 kN enters the adjusted-life check. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.0079 at the 9,000 r/min limiting speed raises the required axial preload to about 718 N; the reference-speed value 352 N is the thermal design point. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 25 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 18.2/39 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "vertical pump and motor shaft thrust",
      "crane hooks and lifting-block pins",
      "machine-tool adjustment screws and tailstock centres"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 18.2 kN track before first rotation.",
      "When the housing seat cannot be machined square to the 25 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 18.2/39 kN and the available 42 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51105 against two-way load lifts the loose washer off its raceway.",
      "The 18.2/39 kN figures belong to 51105 specifically (the single flat pressed steel execution of 51105); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51105-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 25 mm, OD 42 mm, height 11 mm; weight 56 g. Load figures from SKF 17000: dynamic 18.2 kN, static 39 kN, fatigue limit 1.43 kN; reference speed 6,300 r/min (thermal) and limiting speed 9,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51105 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 05 decodes to 25 mm (code 05 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51105-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 25 mm shaft must go to a separate radial bearing; mixed loading through 51105 edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51105",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51105-SKF",
      "51105"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51205-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51205",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 47,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 50,
    "fatigue_load_limit_kN": 1.86,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51205 is an ISO 104 single-direction thrust ball bearing, 25 mm bore and 47 mm OD on a flat housing seat, standing 15 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 05: bore 25 mm (code 05 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 25×47×15 mm (0.984×1.85×0.591 in), 11.0 mm radial section, C 26.5 kN, C0 50 kN, Pu 1.86 kN. reference speed 5,300 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 110 g. Speed band width for this size is 2,200 r/min between reference and limiting (1.42× ratio); lubrication, preload and heat removal decide where inside that band 51205 can actually run. Section proportions: the 11.0 mm radial section compares with 25 mm of bore (section/bore ≈ 0.44) and the 15 mm height is 1.36× that section — the proportions that identify the 51200 envelope at a glance. Stack/annulus proportions: the 15 mm axial stack over the 1,244 mm² washer annulus gives 12.06 mm of height per annular square millimetre ×10⁻³, and at 110 g the bearing holds about 454.5 kN of C0 per kilogram. Load balance: C0 50 kN against C 26.5 kN gives a 1.89 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 1.86 kN enters the adjusted-life check. At the printed limiting speed of 7,500 r/min the mean pitch diameter dm ≈ 36.0 mm implies a dn value around 270k mm·r/min; the 5,300 r/min reference speed is the thermal-planning value under catalogue load. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 15 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 26.5 kN C.",
    "applications": [
      "machine-tool adjustment screws and tailstock centres",
      "screw jacks and press-adjustment spindles",
      "vertical pump and motor shaft thrust"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 26.5 kN track before first rotation.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.015; for 51205 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 51205 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 25 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "When the housing seat cannot be machined square to the 25 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "The 26.5/50 kN figures belong to 51205 specifically (the single flat pressed steel execution of 51205); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51205-SKF?",
        "a": "The catalogue envelope is 25×47×15 mm, mass 110 g; ratings C 26.5 kN / C0 50 kN / Pu 1.86 kN, reference speed 5,300 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51205 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 05: bore 25 mm (code 05 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "Can 51205-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 25 mm shaft must go to a separate radial bearing; mixed loading through 51205 edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51205",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51205-SKF",
      "51205"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51305-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51305",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 34.5,
    "static_load_kN": 60,
    "fatigue_load_limit_kN": 2.24,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 170,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51305 is an ISO 104 single-direction thrust ball bearing, 25 mm bore and 52 mm OD on a flat housing seat, standing 18 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 05: bore 25 mm (code 05 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 25×52×18 mm (0.984×2.047×0.709 in), 13.5 mm radial section, C 34.5 kN, C0 60 kN, Pu 2.24 kN. reference speed 4,500 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 170 g. Bore-to-OD planning: OD 52 over bore 25 is a 2.08× step for this size, and the 18 mm height gives a bore/height ratio of 1.39; use these ratios when the housing recess around the 25 mm shaft is the first constraint. Light-load floor: Pu = 2.24 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51305; the number is 6 % of the 34.5 kN dynamic rating. Mass and section check: 170 g inside the 25×52×18 mm outline leaves a 13.5 mm radial section, and the 60 kN static rating is 1.74× the dynamic rating — plan static safety and minimum preload against those figures. Speed band width for this size is 1,800 r/min between reference and limiting (1.40× ratio); lubrication, preload and heat removal decide where inside that band 51305 can actually run. Minimum-load arithmetic: with dm ≈ 38.5 mm and factor A 0.018, Fam ≈ A·(n·dm/1000)² at the 4,500 r/min reference speed is about 540 N for 51305; below that preload the balls skid and smear the tracks. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 18 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 34.5 kN C.",
    "applications": [
      "low-speed reducer thrust positions",
      "screw jacks and press-adjustment spindles",
      "machine-tool adjustment screws and tailstock centres"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 34.5/60 kN and the available 52 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.018; for 51305 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51305 against two-way load lifts the loose washer off its raceway.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 18 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Ordering discipline for 51305: the catalogue page quotes 51305 and its 34.5/60 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51305-SKF?",
        "a": "The catalogue envelope is 25×52×18 mm, mass 170 g; ratings C 34.5 kN / C0 60 kN / Pu 2.24 kN, reference speed 4,500 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51305 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 05: bore 25 mm (code 05 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51305-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.018 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51305",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51305-SKF",
      "51305"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51405-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51405",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 60,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 42.3,
    "static_load_kN": 67,
    "fatigue_load_limit_kN": 2.45,
    "reference_speed_rpm": 3600,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51400 series order number 51405 is a SKF single-direction thrust ball bearing for a 25 mm seat, built to ISO 104, with a flat housing seating surface, 25×60×24 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 05 decodes to 25 mm (code 05 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 25×60×24 mm (0.984×2.362×0.945 in), 17.5 mm radial section, C 42.3 kN, C0 67 kN, Pu 2.45 kN. reference speed 3,600 r/min (thermal) and limiting speed 5,000 r/min (mechanical), catalogue mass 340 g. Static-first selection data: 67 kN C0 spread across the 24 mm stack gives 2.8 kN of static rating per height millimetre, and the 340 g mass/C0 ratio is about 5 g per static kN — crane-hook and screw positions are normally sized on these two figures. At the printed limiting speed of 5,000 r/min the mean pitch diameter dm ≈ 42.5 mm implies a dn value around 213k mm·r/min; the 3,600 r/min reference speed is the thermal-planning value under catalogue load. Selection figures for 51405: the C0/C ratio is 1.58, Pu 2.45 kN is about 6 % of C, and the catalogue mass works out to roughly 14 g per millimetre of bore; the printed minimum-load factor is A 0.048. Mass and section check: 340 g inside the 25×60×24 mm outline leaves a 17.5 mm radial section, and the 67 kN static rating is 1.58× the dynamic rating — plan static safety and minimum preload against those figures. Speed-ratio note for this exact unit: the reference speed is 3,600 r/min against a 5,000 r/min limiting speed, a reference-to-limit ratio of 0.72. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 25 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 42.3/67 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "screw jacks and press-adjustment spindles",
      "low-speed reducer thrust positions",
      "crane hooks and lifting-block pins"
    ],
    "failure_modes": [
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 42.3 kN track before first rotation.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51405 against two-way load lifts the loose washer off its raceway.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.048; for 51405 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 51405 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 25 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The 42.3/67 kN figures belong to 51405 specifically (the single flat pressed steel execution of 51405); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51405-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 25 mm, OD 60 mm, height 24 mm; weight 340 g. Load figures from SKF 17000: dynamic 42.3 kN, static 67 kN, fatigue limit 2.45 kN; reference speed 3,600 r/min (thermal) and limiting speed 5,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51405 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 05 decodes to 25 mm (code 05 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51405-SKF?",
        "a": "The 3,600 r/min reference speed is the thermal balance under catalogue load; the 5,000 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51405-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.048 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51405",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×60×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51405-SKF",
      "51405"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51106-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51106",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 47,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 19,
    "static_load_kN": 43,
    "fatigue_load_limit_kN": 1.6,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 63,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51106 is SKF's 30 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 30×47×11 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 06 encode the bore as 30 mm (code 06 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 30×47×11 mm (1.181×1.85×0.433 in), 8.5 mm radial section, C 19 kN, C0 43 kN, Pu 1.6 kN. reference speed 6,000 r/min (thermal) and limiting speed 8,500 r/min (mechanical), catalogue mass 63 g. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51106 covers about 1,028 mm², distributing C0 43 kN over a mean track circle of π·dm ≈ 121 mm. Imperial cross-check for procurement drawings: 1.181 in bore, 1.85 in OD, 0.433 in height, and the 63 g catalogue mass converts to 0.063 kg (2.2 oz). Stack/annulus proportions: the 11 mm axial stack over the 1,028 mm² washer annulus gives 10.70 mm of height per annular square millimetre ×10⁻³, and at 63 g the bearing holds about 682.5 kN of C0 per kilogram. Speed-ratio note for this exact unit: the reference speed is 6,000 r/min against a 8,500 r/min limiting speed, a reference-to-limit ratio of 0.71. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.0096 at the 8,500 r/min limiting speed raises the required axial preload to about 1.0 kN; the reference-speed value 512 N is the thermal design point. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 30 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 19/43 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "machine-tool adjustment screws and tailstock centres",
      "crane hooks and lifting-block pins",
      "low-speed reducer thrust positions"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 11 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "When the housing seat cannot be machined square to the 30 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 19 kN track before first rotation.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51106 as the single flat pressed steel execution; other order numbers of the 51106 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51106-SKF?",
        "a": "51106 measures 30 mm bore × 47 mm OD × 11 mm bearing height (1.181 × 1.85 × 0.433 in), mass about 63 g. SKF 17000 ratings: C 19 kN, C0 43 kN, Pu 1.6 kN, reference speed 6,000 r/min (thermal) and limiting speed 8,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51106 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 06 encode the bore as 30 mm (code 06 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "Can 51106-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 30 mm shaft must go to a separate radial bearing; mixed loading through 51106 edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51106",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51106-SKF",
      "51106"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51206-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51206",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 52,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 25.1,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 1.86,
    "reference_speed_rpm": 4800,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51206 is SKF's 30 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 30×52×16 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 06 encode the bore as 30 mm (code 06 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 30×52×16 mm (1.181×2.047×0.63 in), 11.0 mm radial section, C 25.1 kN, C0 51 kN, Pu 1.86 kN. reference speed 4,800 r/min (thermal) and limiting speed 6,700 r/min (mechanical), catalogue mass 130 g. Mass and section check: 130 g inside the 30×52×16 mm outline leaves a 11.0 mm radial section, and the 51 kN static rating is 2.03× the dynamic rating — plan static safety and minimum preload against those figures. Minimum-load arithmetic: with dm ≈ 41.0 mm and factor A 0.013, Fam ≈ A·(n·dm/1000)² at the 4,800 r/min reference speed is about 503 N for 51206; below that preload the balls skid and smear the tracks. Speed-ratio note for this exact unit: the reference speed is 4,800 r/min against a 6,700 r/min limiting speed, a reference-to-limit ratio of 0.72. Capacity density: 25.1 kN C from 0.130 kg of bearing steel gives about 193.1 kN per kilogram; static density is correspondingly 392.3 kN/kg at C0 51 kN. Section proportions: the 11.0 mm radial section compares with 30 mm of bore (section/bore ≈ 0.37) and the 16 mm height is 1.45× that section — the proportions that identify the 51200 envelope at a glance. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 30 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 25.1/51 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "machine-tool adjustment screws and tailstock centres",
      "screw jacks and press-adjustment spindles",
      "low-speed reducer thrust positions"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "When the housing seat cannot be machined square to the 30 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 30 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.013; for 51206 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 25.1/51 kN figures belong to 51206 specifically (the single flat pressed steel execution of 51206); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51206-SKF?",
        "a": "51206 measures 30 mm bore × 52 mm OD × 16 mm bearing height (1.181 × 2.047 × 0.63 in), mass about 130 g. SKF 17000 ratings: C 25.1 kN, C0 51 kN, Pu 1.86 kN, reference speed 4,800 r/min (thermal) and limiting speed 6,700 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51206 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 06 encode the bore as 30 mm (code 06 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51206-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 30 mm shaft must go to a separate radial bearing; mixed loading through 51206 edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51206",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×52×16 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51206-SKF",
      "51206"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51306-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51306",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 60,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 35.8,
    "static_load_kN": 65.5,
    "fatigue_load_limit_kN": 2.4,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 260,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51306 is SKF's 30 mm-bore single-direction thrust ball bearing in the 51300 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 30×60×21 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 06 encode the bore as 30 mm (code 06 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 30×60×21 mm (1.181×2.362×0.827 in), 15.0 mm radial section, C 35.8 kN, C0 65.5 kN, Pu 2.4 kN. reference speed 3,800 r/min (thermal) and limiting speed 5,300 r/min (mechanical), catalogue mass 260 g. Bore-to-OD planning: OD 60 over bore 30 is a 2.00× step for this size, and the 21 mm height gives a bore/height ratio of 1.43; use these ratios when the housing recess around the 30 mm shaft is the first constraint. Envelope economics: the 21 mm axial height over a 15.0 mm radial section yields 1.7 kN of dynamic capacity per height millimetre, and the bearing weighs 260 g for 35.8 kN C — about 7 g per rated kN. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 5,300 r/min while thermal balance under catalogue load sets the 3,800 r/min reference; at dm ≈ 45.0 mm the corresponding dn is approximately 239k mm·r/min. Rating split for documentation: dynamic 35.8 kN (L10 life), static 65.5 kN (safety factor s0), fatigue limit 2.4 kN (adjusted life) — three different uses of three different numbers for 51306, none interchangeable with another. Section proportions: the 15.0 mm radial section compares with 30 mm of bore (section/bore ≈ 0.50) and the 21 mm height is 1.40× that section — the proportions that identify the 51300 envelope at a glance. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 30 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 35.8/65.5 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "vertical pump and motor shaft thrust",
      "low-speed reducer thrust positions",
      "crane hooks and lifting-block pins"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 30 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51300 bearing.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 30 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 21 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Ordering discipline for 51306: the catalogue page quotes 51306 and its 35.8/65.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51306-SKF?",
        "a": "51306 measures 30 mm bore × 60 mm OD × 21 mm bearing height (1.181 × 2.362 × 0.827 in), mass about 260 g. SKF 17000 ratings: C 35.8 kN, C0 65.5 kN, Pu 2.4 kN, reference speed 3,800 r/min (thermal) and limiting speed 5,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51306 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 06 encode the bore as 30 mm (code 06 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51306-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 5,300 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51306",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×60×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51306-SKF",
      "51306"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51406-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51406",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 70,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 70.2,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 3000,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 520,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51406 is an ISO 104 single-direction thrust ball bearing, 30 mm bore and 70 mm OD on a flat housing seat, standing 28 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 06: bore 30 mm (code 06 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 30×70×28 mm (1.181×2.756×1.102 in), 20.0 mm radial section, C 70.2 kN, C0 122 kN, Pu 4.5 kN. reference speed 3,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 520 g. At the printed limiting speed of 4,300 r/min the mean pitch diameter dm ≈ 50.0 mm implies a dn value around 215k mm·r/min; the 3,000 r/min reference speed is the thermal-planning value under catalogue load. Mass and section check: 520 g inside the 30×70×28 mm outline leaves a 20.0 mm radial section, and the 122 kN static rating is 1.74× the dynamic rating — plan static safety and minimum preload against those figures. Pitch-diameter arithmetic: dm = (30+70)/2 = 50.0 mm; at the 4,300 r/min limiting speed that corresponds to roughly 215k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Rating split for documentation: dynamic 70.2 kN (L10 life), static 122 kN (safety factor s0), fatigue limit 4.5 kN (adjusted life) — three different uses of three different numbers for 51406, none interchangeable with another. Minimum-load arithmetic: with dm ≈ 50.0 mm and factor A 0.097, Fam ≈ A·(n·dm/1000)² at the 3,000 r/min reference speed is about 2.2 kN for 51406; below that preload the balls skid and smear the tracks. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 28 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 70.2 kN C.",
    "applications": [
      "vertical pump and motor shaft thrust",
      "machine-tool adjustment screws and tailstock centres",
      "low-speed reducer thrust positions"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51406 against two-way load lifts the loose washer off its raceway.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 28 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 30 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51406 as the single flat pressed steel execution; other order numbers of the 51406 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51406-SKF?",
        "a": "The catalogue envelope is 30×70×28 mm, mass 520 g; ratings C 70.2 kN / C0 122 kN / Pu 4.5 kN, reference speed 3,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51406 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 06: bore 30 mm (code 06 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51406-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 4,300 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 30 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51406",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51406-SKF",
      "51406"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51107-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51107",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 52,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 19.9,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 1.86,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 80,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51107 is a SKF single-direction thrust ball bearing for a 35 mm seat, built to ISO 104, with a flat housing seating surface, 35×52×12 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 07 decodes to 35 mm (code 07 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 35×52×12 mm (1.378×2.047×0.472 in), 8.5 mm radial section, C 19.9 kN, C0 51 kN, Pu 1.86 kN. reference speed 5,600 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 80 g. Load balance: C0 51 kN against C 19.9 kN gives a 2.56 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 1.86 kN enters the adjusted-life check. Sizing arithmetic on the 35 mm bore: 19.9 kN C over the 8.5 mm radial section gives 2.3 kN per section millimetre, and the 12 mm stack height is 1.41× that section — proportions typical of a 51100 thrust section. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51107 covers about 1,162 mm², distributing C0 51 kN over a mean track circle of π·dm ≈ 137 mm. Rating split for documentation: dynamic 19.9 kN (L10 life), static 51 kN (safety factor s0), fatigue limit 1.86 kN (adjusted life) — three different uses of three different numbers for 51107, none interchangeable with another. Imperial cross-check for procurement drawings: 1.378 in bore, 2.047 in OD, 0.472 in height, and the 80 g catalogue mass converts to 0.080 kg (2.8 oz). Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 35 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 19.9/51 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "vertical pump and motor shaft thrust",
      "screw jacks and press-adjustment spindles",
      "machine-tool adjustment screws and tailstock centres"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 19.9 kN track before first rotation.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 35 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "When the housing seat cannot be machined square to the 35 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 19.9/51 kN and the available 52 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 19.9/51 kN figures belong to 51107 specifically (the single flat pressed steel execution of 51107); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51107-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 35 mm, OD 52 mm, height 12 mm; weight 80 g. Load figures from SKF 17000: dynamic 19.9 kN, static 51 kN, fatigue limit 1.86 kN; reference speed 5,600 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51107 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 07 decodes to 35 mm (code 07 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51107-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.013 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51107",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×52×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51107-SKF",
      "51107"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51207-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51207",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 62,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 35.1,
    "static_load_kN": 73.5,
    "fatigue_load_limit_kN": 2.7,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51207 is an ISO 104 single-direction thrust ball bearing, 35 mm bore and 62 mm OD on a flat housing seat, standing 18 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 07: bore 35 mm (code 07 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 35×62×18 mm (1.378×2.441×0.709 in), 13.5 mm radial section, C 35.1 kN, C0 73.5 kN, Pu 2.7 kN. reference speed 4,000 r/min (thermal) and limiting speed 5,600 r/min (mechanical), catalogue mass 220 g. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.028 at the 5,600 r/min limiting speed raises the required axial preload to about 2.1 kN; the reference-speed value 1.1 kN is the thermal design point. Bore-to-OD planning: OD 62 over bore 35 is a 1.77× step for this size, and the 18 mm height gives a bore/height ratio of 1.94; use these ratios when the housing recess around the 35 mm shaft is the first constraint. Stack/annulus proportions: the 18 mm axial stack over the 2,057 mm² washer annulus gives 8.75 mm of height per annular square millimetre ×10⁻³, and at 220 g the bearing holds about 334.1 kN of C0 per kilogram. At the printed limiting speed of 5,600 r/min the mean pitch diameter dm ≈ 48.5 mm implies a dn value around 272k mm·r/min; the 4,000 r/min reference speed is the thermal-planning value under catalogue load. Pitch-diameter arithmetic: dm = (35+62)/2 = 48.5 mm; at the 5,600 r/min limiting speed that corresponds to roughly 272k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 18 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 35.1 kN C.",
    "applications": [
      "machine-tool adjustment screws and tailstock centres",
      "crane hooks and lifting-block pins",
      "low-speed reducer thrust positions"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 35.1/73.5 kN and the available 62 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 35 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 18 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51207 against two-way load lifts the loose washer off its raceway.",
      "Ordering discipline for 51207: the catalogue page quotes 51207 and its 35.1/73.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51207-SKF?",
        "a": "The catalogue envelope is 35×62×18 mm, mass 220 g; ratings C 35.1 kN / C0 73.5 kN / Pu 2.7 kN, reference speed 4,000 r/min (thermal) and limiting speed 5,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51207 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 07: bore 35 mm (code 07 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51207-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 5,600 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51207",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51207-SKF",
      "51207"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51307-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51307",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 68,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 49.4,
    "static_load_kN": 96.5,
    "fatigue_load_limit_kN": 3.55,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 390,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51307 is an ISO 104 single-direction thrust ball bearing, 35 mm bore and 68 mm OD on a flat housing seat, standing 24 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 07: bore 35 mm (code 07 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 35×68×24 mm (1.378×2.677×0.945 in), 16.5 mm radial section, C 49.4 kN, C0 96.5 kN, Pu 3.55 kN. reference speed 3,400 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 390 g. Pitch-diameter arithmetic: dm = (35+68)/2 = 51.5 mm; at the 4,800 r/min limiting speed that corresponds to roughly 247k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.048 at the 4,800 r/min limiting speed raises the required axial preload to about 2.9 kN; the reference-speed value 1.5 kN is the thermal design point. At the printed limiting speed of 4,800 r/min the mean pitch diameter dm ≈ 51.5 mm implies a dn value around 247k mm·r/min; the 3,400 r/min reference speed is the thermal-planning value under catalogue load. Rating split for documentation: dynamic 49.4 kN (L10 life), static 96.5 kN (safety factor s0), fatigue limit 3.55 kN (adjusted life) — three different uses of three different numbers for 51307, none interchangeable with another. Stack/annulus proportions: the 24 mm axial stack over the 2,670 mm² washer annulus gives 8.99 mm of height per annular square millimetre ×10⁻³, and at 390 g the bearing holds about 247.4 kN of C0 per kilogram. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 35 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 49.4/96.5 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "low-speed reducer thrust positions",
      "crane hooks and lifting-block pins",
      "machine-tool adjustment screws and tailstock centres"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 49.4/96.5 kN and the available 68 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 24 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The 51307 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 35 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51307 against two-way load lifts the loose washer off its raceway.",
      "Ordering discipline for 51307: the catalogue page quotes 51307 and its 49.4/96.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51307-SKF?",
        "a": "The catalogue envelope is 35×68×24 mm, mass 390 g; ratings C 49.4 kN / C0 96.5 kN / Pu 3.55 kN, reference speed 3,400 r/min (thermal) and limiting speed 4,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51307 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 07: bore 35 mm (code 07 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51307-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 35 mm shaft must go to a separate radial bearing; mixed loading through 51307 edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51307",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×68×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51307-SKF",
      "51307"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51407-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51407",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 76.1,
    "static_load_kN": 137,
    "fatigue_load_limit_kN": 5.1,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 790,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51400 series order number 51407 is a SKF single-direction thrust ball bearing for a 35 mm seat, built to ISO 104, with a flat housing seating surface, 35×80×32 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 07 decodes to 35 mm (code 07 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 35×80×32 mm (1.378×3.15×1.26 in), 22.5 mm radial section, C 76.1 kN, C0 137 kN, Pu 5.1 kN. reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 790 g. Speed band width for this size is 1,000 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 51407 can actually run. Track-circle loading: per millimetre of mean track circumference the 76.1 kN dynamic rating corresponds to roughly 0.42 kN/mm of π·dm track, a useful comparison against the other dimension series of the 35 mm bore. Capacity density: 76.1 kN C from 0.790 kg of bearing steel gives about 96.3 kN per kilogram; static density is correspondingly 173.4 kN/kg at C0 137 kN. Section proportions: the 22.5 mm radial section compares with 35 mm of bore (section/bore ≈ 0.64) and the 32 mm height is 1.42× that section — the proportions that identify the 51400 envelope at a glance. Envelope economics: the 32 mm axial height over a 22.5 mm radial section yields 2.4 kN of dynamic capacity per height millimetre, and the bearing weighs 790 g for 76.1 kN C — about 10 g per rated kN. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 32 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 76.1 kN C.",
    "applications": [
      "crane hooks and lifting-block pins",
      "screw jacks and press-adjustment spindles",
      "vertical pump and motor shaft thrust"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "The 51407 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 35 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.15; for 51407 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51407 against two-way load lifts the loose washer off its raceway.",
      "The 76.1/137 kN figures belong to 51407 specifically (the single flat pressed steel execution of 51407); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51407-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 35 mm, OD 80 mm, height 32 mm; weight 790 g. Load figures from SKF 17000: dynamic 76.1 kN, static 137 kN, fatigue limit 5.1 kN; reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51407 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 07 decodes to 35 mm (code 07 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 35 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51407 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51407",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×80×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51407-SKF",
      "51407"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51108-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51108",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 60,
    "B_mm": 13,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 25.5,
    "static_load_kN": 63,
    "fatigue_load_limit_kN": 2.32,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 120,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51108 is SKF's 40 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 40×60×13 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 08 encode the bore as 40 mm (code 08 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 40×60×13 mm (1.575×2.362×0.512 in), 10.0 mm radial section, C 25.5 kN, C0 63 kN, Pu 2.32 kN. reference speed 5,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), catalogue mass 120 g. Static-first selection data: 63 kN C0 spread across the 13 mm stack gives 4.8 kN of static rating per height millimetre, and the 120 g mass/C0 ratio is about 2 g per static kN — crane-hook and screw positions are normally sized on these two figures. Capacity density: 25.5 kN C from 0.120 kg of bearing steel gives about 212.5 kN per kilogram; static density is correspondingly 525.0 kN/kg at C0 63 kN. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51108 covers about 1,571 mm², distributing C0 63 kN over a mean track circle of π·dm ≈ 157 mm. Sizing arithmetic on the 40 mm bore: 25.5 kN C over the 10.0 mm radial section gives 2.5 kN per section millimetre, and the 13 mm stack height is 1.30× that section — proportions typical of a 51100 thrust section. Imperial cross-check for procurement drawings: 1.575 in bore, 2.362 in OD, 0.512 in height, and the 120 g catalogue mass converts to 0.120 kg (4.2 oz). Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 40 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 25.5/63 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "vertical pump and motor shaft thrust",
      "screw jacks and press-adjustment spindles",
      "low-speed reducer thrust positions"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 25.5 kN track before first rotation.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 13 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 40 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51108 against two-way load lifts the loose washer off its raceway.",
      "The 25.5/63 kN figures belong to 51108 specifically (the single flat pressed steel execution of 51108); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51108-SKF?",
        "a": "51108 measures 40 mm bore × 60 mm OD × 13 mm bearing height (1.575 × 2.362 × 0.512 in), mass about 120 g. SKF 17000 ratings: C 25.5 kN, C0 63 kN, Pu 2.32 kN, reference speed 5,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51108 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 08 encode the bore as 40 mm (code 08 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51108-SKF?",
        "a": "The 5,000 r/min reference speed is the thermal balance under catalogue load; the 7,000 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51108-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.02 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51108",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51108-SKF",
      "51108"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51208-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51208",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 68,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 44.2,
    "static_load_kN": 96.5,
    "fatigue_load_limit_kN": 3.6,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 280,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51208 is SKF's 40 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 40×68×19 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 08 encode the bore as 40 mm (code 08 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 40×68×19 mm (1.575×2.677×0.748 in), 14.0 mm radial section, C 44.2 kN, C0 96.5 kN, Pu 3.6 kN. reference speed 3,800 r/min (thermal) and limiting speed 5,300 r/min (mechanical), catalogue mass 280 g. Speed-ratio note for this exact unit: the reference speed is 3,800 r/min against a 5,300 r/min limiting speed, a reference-to-limit ratio of 0.72. Stack/annulus proportions: the 19 mm axial stack over the 2,375 mm² washer annulus gives 8.00 mm of height per annular square millimetre ×10⁻³, and at 280 g the bearing holds about 344.6 kN of C0 per kilogram. Light-load floor: Pu = 3.6 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51208; the number is 8 % of the 44.2 kN dynamic rating. Capacity density: 44.2 kN C from 0.280 kg of bearing steel gives about 157.9 kN per kilogram; static density is correspondingly 344.6 kN/kg at C0 96.5 kN. Track-circle loading: per millimetre of mean track circumference the 44.2 kN dynamic rating corresponds to roughly 0.26 kN/mm of π·dm track, a useful comparison against the other dimension series of the 40 mm bore. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 19 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 44.2 kN C.",
    "applications": [
      "machine-tool adjustment screws and tailstock centres",
      "screw jacks and press-adjustment spindles",
      "vertical pump and motor shaft thrust"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.058; for 51208 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51208 against two-way load lifts the loose washer off its raceway.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "The 51208 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 40 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Ordering discipline for 51208: the catalogue page quotes 51208 and its 44.2/96.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51208-SKF?",
        "a": "51208 measures 40 mm bore × 68 mm OD × 19 mm bearing height (1.575 × 2.677 × 0.748 in), mass about 280 g. SKF 17000 ratings: C 44.2 kN, C0 96.5 kN, Pu 3.6 kN, reference speed 3,800 r/min (thermal) and limiting speed 5,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51208 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 08 encode the bore as 40 mm (code 08 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51208-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 5,300 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 40 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51208",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51208-SKF",
      "51208"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51308-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51308",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 78,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 61.8,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 3000,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 530,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51308 is SKF's 40 mm-bore single-direction thrust ball bearing in the 51300 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 40×78×26 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 08 encode the bore as 40 mm (code 08 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 40×78×26 mm (1.575×3.071×1.024 in), 19.0 mm radial section, C 61.8 kN, C0 122 kN, Pu 4.5 kN. reference speed 3,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 530 g. Mass and section check: 530 g inside the 40×78×26 mm outline leaves a 19.0 mm radial section, and the 122 kN static rating is 1.97× the dynamic rating — plan static safety and minimum preload against those figures. Envelope economics: the 26 mm axial height over a 19.0 mm radial section yields 2.4 kN of dynamic capacity per height millimetre, and the bearing weighs 530 g for 61.8 kN C — about 9 g per rated kN. Minimum-load arithmetic: with dm ≈ 59.0 mm and factor A 0.077, Fam ≈ A·(n·dm/1000)² at the 3,000 r/min reference speed is about 2.4 kN for 51308; below that preload the balls skid and smear the tracks. Imperial cross-check for procurement drawings: 1.575 in bore, 3.071 in OD, 1.024 in height, and the 530 g catalogue mass converts to 0.530 kg (18.7 oz). Rating split for documentation: dynamic 61.8 kN (L10 life), static 122 kN (safety factor s0), fatigue limit 4.5 kN (adjusted life) — three different uses of three different numbers for 51308, none interchangeable with another. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 26 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 61.8 kN C.",
    "applications": [
      "screw jacks and press-adjustment spindles",
      "crane hooks and lifting-block pins",
      "low-speed reducer thrust positions"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "track rust staining from condensate during long idle periods in humid plant air"
    ],
    "pitfalls": [
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 40 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The 51308 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 40 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "When the housing seat cannot be machined square to the 40 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51300 bearing.",
      "The 61.8/122 kN figures belong to 51308 specifically (the single flat pressed steel execution of 51308); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51308-SKF?",
        "a": "51308 measures 40 mm bore × 78 mm OD × 26 mm bearing height (1.575 × 3.071 × 1.024 in), mass about 530 g. SKF 17000 ratings: C 61.8 kN, C0 122 kN, Pu 4.5 kN, reference speed 3,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51308 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 08 encode the bore as 40 mm (code 08 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 40 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51308 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51308",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×78×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51308-SKF",
      "51308"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51408-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51408",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 95.6,
    "static_load_kN": 183,
    "fatigue_load_limit_kN": 6.8,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51408 is an ISO 104 single-direction thrust ball bearing, 40 mm bore and 90 mm OD on a flat housing seat, standing 36 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 08: bore 40 mm (code 08 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 40×90×36 mm (1.575×3.543×1.417 in), 25.0 mm radial section, C 95.6 kN, C0 183 kN, Pu 6.8 kN. reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 1100 g. Stack/annulus proportions: the 36 mm axial stack over the 5,105 mm² washer annulus gives 7.05 mm of height per annular square millimetre ×10⁻³, and at 1100 g the bearing holds about 166.4 kN of C0 per kilogram. Speed band width for this size is 1,000 r/min between reference and limiting (1.42× ratio); lubrication, preload and heat removal decide where inside that band 51408 can actually run. Imperial cross-check for procurement drawings: 1.575 in bore, 3.543 in OD, 1.417 in height, and the 1100 g catalogue mass converts to 1.100 kg (38.8 oz). Rating split for documentation: dynamic 95.6 kN (L10 life), static 183 kN (safety factor s0), fatigue limit 6.8 kN (adjusted life) — three different uses of three different numbers for 51408, none interchangeable with another. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.26 at the 3,400 r/min limiting speed raises the required axial preload to about 12.7 kN; the reference-speed value 6.3 kN is the thermal design point. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 40 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 95.6/183 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "machine-tool adjustment screws and tailstock centres",
      "crane hooks and lifting-block pins",
      "screw jacks and press-adjustment spindles"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 36 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "The 51408 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 40 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.26; for 51408 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51408 as the single flat pressed steel execution; other order numbers of the 51408 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51408-SKF?",
        "a": "The catalogue envelope is 40×90×36 mm, mass 1100 g; ratings C 95.6 kN / C0 183 kN / Pu 6.8 kN, reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51408 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 08: bore 40 mm (code 08 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51408-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 40 mm shaft must go to a separate radial bearing; mixed loading through 51408 edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51408",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×90×36 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51408-SKF",
      "51408"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51109-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51109",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 65,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 69.5,
    "fatigue_load_limit_kN": 2.55,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51109 is SKF's 45 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 45×65×14 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 09 encode the bore as 45 mm (code 09 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 45×65×14 mm (1.772×2.559×0.551 in), 10.0 mm radial section, C 26.5 kN, C0 69.5 kN, Pu 2.55 kN. reference speed 4,500 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 140 g. Minimum-load arithmetic: with dm ≈ 55.0 mm and factor A 0.025, Fam ≈ A·(n·dm/1000)² at the 4,500 r/min reference speed is about 1.5 kN for 51109; below that preload the balls skid and smear the tracks. Load balance: C0 69.5 kN against C 26.5 kN gives a 2.62 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 2.55 kN enters the adjusted-life check. Bore-to-OD planning: OD 65 over bore 45 is a 1.44× step for this size, and the 14 mm height gives a bore/height ratio of 3.21; use these ratios when the housing recess around the 45 mm shaft is the first constraint. Light-load floor: Pu = 2.55 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51109; the number is 10 % of the 26.5 kN dynamic rating. Static-first selection data: 69.5 kN C0 spread across the 14 mm stack gives 5.0 kN of static rating per height millimetre, and the 140 g mass/C0 ratio is about 2 g per static kN — crane-hook and screw positions are normally sized on these two figures. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 45 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 26.5/69.5 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "vertical pump and motor shaft thrust",
      "machine-tool adjustment screws and tailstock centres",
      "low-speed reducer thrust positions"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 26.5/69.5 kN and the available 65 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 26.5 kN track before first rotation.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.025; for 51109 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Ordering discipline for 51109: the catalogue page quotes 51109 and its 26.5/69.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51109-SKF?",
        "a": "51109 measures 45 mm bore × 65 mm OD × 14 mm bearing height (1.772 × 2.559 × 0.551 in), mass about 140 g. SKF 17000 ratings: C 26.5 kN, C0 69.5 kN, Pu 2.55 kN, reference speed 4,500 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51109 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 09 encode the bore as 45 mm (code 09 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51109 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51109-SKF?",
        "a": "The 4,500 r/min reference speed is the thermal balance under catalogue load; the 6,300 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51109",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51109-SKF",
      "51109"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51209-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51209",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 73,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 39,
    "static_load_kN": 86.5,
    "fatigue_load_limit_kN": 3.2,
    "reference_speed_rpm": 3600,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51209 is SKF's 45 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 45×73×20 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 09 encode the bore as 45 mm (code 09 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 45×73×20 mm (1.772×2.874×0.787 in), 14.0 mm radial section, C 39 kN, C0 86.5 kN, Pu 3.2 kN. reference speed 3,600 r/min (thermal) and limiting speed 5,000 r/min (mechanical), catalogue mass 300 g. Load balance: C0 86.5 kN against C 39 kN gives a 2.22 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 3.2 kN enters the adjusted-life check. Static-first selection data: 86.5 kN C0 spread across the 20 mm stack gives 4.3 kN of static rating per height millimetre, and the 300 g mass/C0 ratio is about 3 g per static kN — crane-hook and screw positions are normally sized on these two figures. Speed band width for this size is 1,400 r/min between reference and limiting (1.39× ratio); lubrication, preload and heat removal decide where inside that band 51209 can actually run. Sizing arithmetic on the 45 mm bore: 39 kN C over the 14.0 mm radial section gives 2.8 kN per section millimetre, and the 20 mm stack height is 1.43× that section — proportions typical of a 51200 thrust section. Track-circle loading: per millimetre of mean track circumference the 39 kN dynamic rating corresponds to roughly 0.21 kN/mm of π·dm track, a useful comparison against the other dimension series of the 45 mm bore. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 20 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 39 kN C.",
    "applications": [
      "screw jacks and press-adjustment spindles",
      "low-speed reducer thrust positions",
      "crane hooks and lifting-block pins"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 45 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 45 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.038; for 51209 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Ordering discipline for 51209: the catalogue page quotes 51209 and its 39/86.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51209-SKF?",
        "a": "51209 measures 45 mm bore × 73 mm OD × 20 mm bearing height (1.772 × 2.874 × 0.787 in), mass about 300 g. SKF 17000 ratings: C 39 kN, C0 86.5 kN, Pu 3.2 kN, reference speed 3,600 r/min (thermal) and limiting speed 5,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51209 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 09 encode the bore as 45 mm (code 09 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 45 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51209 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51209",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×73×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51209-SKF",
      "51209"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51309-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51309",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 76.1,
    "static_load_kN": 153,
    "fatigue_load_limit_kN": 5.6,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 660,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51300 series order number 51309 is a SKF single-direction thrust ball bearing for a 45 mm seat, built to ISO 104, with a flat housing seating surface, 45×85×28 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 09 decodes to 45 mm (code 09 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 45×85×28 mm (1.772×3.346×1.102 in), 20.0 mm radial section, C 76.1 kN, C0 153 kN, Pu 5.6 kN. reference speed 2,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 660 g. Light-load floor: Pu = 5.6 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51309; the number is 7 % of the 76.1 kN dynamic rating. Capacity density: 76.1 kN C from 0.660 kg of bearing steel gives about 115.3 kN per kilogram; static density is correspondingly 231.8 kN/kg at C0 153 kN. Section proportions: the 20.0 mm radial section compares with 45 mm of bore (section/bore ≈ 0.44) and the 28 mm height is 1.40× that section — the proportions that identify the 51300 envelope at a glance. Static-first selection data: 153 kN C0 spread across the 28 mm stack gives 5.5 kN of static rating per height millimetre, and the 660 g mass/C0 ratio is about 4 g per static kN — crane-hook and screw positions are normally sized on these two figures. Load balance: C0 153 kN against C 76.1 kN gives a 2.01 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 5.6 kN enters the adjusted-life check. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 45 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 76.1/153 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "vertical pump and motor shaft thrust",
      "screw jacks and press-adjustment spindles",
      "low-speed reducer thrust positions"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51309 against two-way load lifts the loose washer off its raceway.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.12; for 51309 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 76.1/153 kN and the available 85 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51309 as the single flat pressed steel execution; other order numbers of the 51309 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51309-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 45 mm, OD 85 mm, height 28 mm; weight 660 g. Load figures from SKF 17000: dynamic 76.1 kN, static 153 kN, fatigue limit 5.6 kN; reference speed 2,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51309 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 09 decodes to 45 mm (code 09 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51309-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 4,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 45 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51309",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51309-SKF",
      "51309"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51409-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51409",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 124,
    "static_load_kN": 240,
    "fatigue_load_limit_kN": 9,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 1400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51409 is SKF's 45 mm-bore single-direction thrust ball bearing in the 51400 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 45×100×39 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 09 encode the bore as 45 mm (code 09 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 45×100×39 mm (1.772×3.937×1.535 in), 27.5 mm radial section, C 124 kN, C0 240 kN, Pu 9 kN. reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 1400 g. Pitch-diameter arithmetic: dm = (45+100)/2 = 72.5 mm; at the 3,000 r/min limiting speed that corresponds to roughly 218k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Imperial cross-check for procurement drawings: 1.772 in bore, 3.937 in OD, 1.535 in height, and the 1400 g catalogue mass converts to 1.400 kg (49.4 oz). Light-load floor: Pu = 9 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51409; the number is 7 % of the 124 kN dynamic rating. Sizing arithmetic on the 45 mm bore: 124 kN C over the 27.5 mm radial section gives 4.5 kN per section millimetre, and the 39 mm stack height is 1.42× that section — proportions typical of a 51400 thrust section. Static-first selection data: 240 kN C0 spread across the 39 mm stack gives 6.2 kN of static rating per height millimetre, and the 1400 g mass/C0 ratio is about 6 g per static kN — crane-hook and screw positions are normally sized on these two figures. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 39 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 124 kN C.",
    "applications": [
      "vertical pump and motor shaft thrust",
      "low-speed reducer thrust positions",
      "crane hooks and lifting-block pins"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51409 against two-way load lifts the loose washer off its raceway.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 45 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "When the housing seat cannot be machined square to the 45 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51400 bearing.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51409 as the single flat pressed steel execution; other order numbers of the 51409 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51409-SKF?",
        "a": "51409 measures 45 mm bore × 100 mm OD × 39 mm bearing height (1.772 × 3.937 × 1.535 in), mass about 1400 g. SKF 17000 ratings: C 124 kN, C0 240 kN, Pu 9 kN, reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51409 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 09 encode the bore as 45 mm (code 09 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51409-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 3,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51409",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51409-SKF",
      "51409"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51110-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51110",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 70,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 27,
    "static_load_kN": 75,
    "fatigue_load_limit_kN": 2.8,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51110 is a SKF single-direction thrust ball bearing for a 50 mm seat, built to ISO 104, with a flat housing seating surface, 50×70×14 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 10 decodes to 50 mm (code 10 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 50×70×14 mm (1.969×2.756×0.551 in), 10.0 mm radial section, C 27 kN, C0 75 kN, Pu 2.8 kN. reference speed 4,300 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 160 g. Speed-ratio note for this exact unit: the reference speed is 4,300 r/min against a 6,300 r/min limiting speed, a reference-to-limit ratio of 0.68. Sizing arithmetic on the 50 mm bore: 27 kN C over the 10.0 mm radial section gives 2.7 kN per section millimetre, and the 14 mm stack height is 1.40× that section — proportions typical of a 51100 thrust section. Minimum-load arithmetic: with dm ≈ 60.0 mm and factor A 0.029, Fam ≈ A·(n·dm/1000)² at the 4,300 r/min reference speed is about 1.9 kN for 51110; below that preload the balls skid and smear the tracks. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.029 at the 6,300 r/min limiting speed raises the required axial preload to about 4.1 kN; the reference-speed value 1.9 kN is the thermal design point. Speed band width for this size is 2,000 r/min between reference and limiting (1.47× ratio); lubrication, preload and heat removal decide where inside that band 51110 can actually run. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 14 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 27 kN C.",
    "applications": [
      "vertical pump and motor shaft thrust",
      "crane hooks and lifting-block pins",
      "low-speed reducer thrust positions"
    ],
    "failure_modes": [
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51110 against two-way load lifts the loose washer off its raceway.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 27/75 kN and the available 70 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 14 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51110 as the single flat pressed steel execution; other order numbers of the 51110 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51110-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 50 mm, OD 70 mm, height 14 mm; weight 160 g. Load figures from SKF 17000: dynamic 27 kN, static 75 kN, fatigue limit 2.8 kN; reference speed 4,300 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51110 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 10 decodes to 50 mm (code 10 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51110-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.029 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51110",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51110-SKF",
      "51110"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51210-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51210",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 78,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 49.4,
    "static_load_kN": 116,
    "fatigue_load_limit_kN": 4.3,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 370,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51210 is a SKF single-direction thrust ball bearing for a 50 mm seat, built to ISO 104, with a flat housing seating surface, 50×78×22 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 10 decodes to 50 mm (code 10 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 50×78×22 mm (1.969×3.071×0.866 in), 14.0 mm radial section, C 49.4 kN, C0 116 kN, Pu 4.3 kN. reference speed 3,400 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 370 g. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 4,500 r/min while thermal balance under catalogue load sets the 3,400 r/min reference; at dm ≈ 64.0 mm the corresponding dn is approximately 288k mm·r/min. Bore-to-OD planning: OD 78 over bore 50 is a 1.56× step for this size, and the 22 mm height gives a bore/height ratio of 2.27; use these ratios when the housing recess around the 50 mm shaft is the first constraint. Section proportions: the 14.0 mm radial section compares with 50 mm of bore (section/bore ≈ 0.28) and the 22 mm height is 1.57× that section — the proportions that identify the 51200 envelope at a glance. Light-load floor: Pu = 4.3 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51210; the number is 9 % of the 49.4 kN dynamic rating. Static-first selection data: 116 kN C0 spread across the 22 mm stack gives 5.3 kN of static rating per height millimetre, and the 370 g mass/C0 ratio is about 3 g per static kN — crane-hook and screw positions are normally sized on these two figures. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 50 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 49.4/116 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "low-speed reducer thrust positions",
      "screw jacks and press-adjustment spindles",
      "machine-tool adjustment screws and tailstock centres"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 49.4 kN track before first rotation.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51210 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 50 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "The 51210 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 50 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The 49.4/116 kN figures belong to 51210 specifically (the single flat pressed steel execution of 51210); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51210-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 50 mm, OD 78 mm, height 22 mm; weight 370 g. Load figures from SKF 17000: dynamic 49.4 kN, static 116 kN, fatigue limit 4.3 kN; reference speed 3,400 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51210 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 10 decodes to 50 mm (code 10 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51210-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 4,500 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51210",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51210-SKF",
      "51210"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51310-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51310",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 95,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 81.9,
    "static_load_kN": 170,
    "fatigue_load_limit_kN": 6.3,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 940,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51310 is SKF's 50 mm-bore single-direction thrust ball bearing in the 51300 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 50×95×31 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 10 encode the bore as 50 mm (code 10 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 50×95×31 mm (1.969×3.74×1.22 in), 22.5 mm radial section, C 81.9 kN, C0 170 kN, Pu 6.3 kN. reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 940 g. Stack/annulus proportions: the 31 mm axial stack over the 5,125 mm² washer annulus gives 6.05 mm of height per annular square millimetre ×10⁻³, and at 940 g the bearing holds about 180.9 kN of C0 per kilogram. Selection figures for 51310: the C0/C ratio is 2.08, Pu 6.3 kN is about 8 % of C, and the catalogue mass works out to roughly 19 g per millimetre of bore; the printed minimum-load factor is A 0.19. Speed band width for this size is 1,000 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 51310 can actually run. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 3,600 r/min while thermal balance under catalogue load sets the 2,600 r/min reference; at dm ≈ 72.5 mm the corresponding dn is approximately 261k mm·r/min. Capacity density: 81.9 kN C from 0.940 kg of bearing steel gives about 87.1 kN per kilogram; static density is correspondingly 180.9 kN/kg at C0 170 kN. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 50 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 81.9/170 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "vertical pump and motor shaft thrust",
      "crane hooks and lifting-block pins",
      "low-speed reducer thrust positions"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 81.9/170 kN and the available 95 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 81.9 kN track before first rotation.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.19; for 51310 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51310 against two-way load lifts the loose washer off its raceway.",
      "Ordering discipline for 51310: the catalogue page quotes 51310 and its 81.9/170 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51310-SKF?",
        "a": "51310 measures 50 mm bore × 95 mm OD × 31 mm bearing height (1.969 × 3.74 × 1.22 in), mass about 940 g. SKF 17000 ratings: C 81.9 kN, C0 170 kN, Pu 6.3 kN, reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51310 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 10 encode the bore as 50 mm (code 10 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51310 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51310-SKF?",
        "a": "The 2,600 r/min reference speed is the thermal balance under catalogue load; the 3,600 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51310",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×95×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51310-SKF",
      "51310"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51410-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51410",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 159,
    "static_load_kN": 340,
    "fatigue_load_limit_kN": 12.5,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 2000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51400 series order number 51410 is a SKF single-direction thrust ball bearing for a 50 mm seat, built to ISO 104, with a flat housing seating surface, 50×110×43 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 10 decodes to 50 mm (code 10 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 50×110×43 mm (1.969×4.331×1.693 in), 30.0 mm radial section, C 159 kN, C0 340 kN, Pu 12.5 kN. reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical), catalogue mass 2000 g. Light-load floor: Pu = 12.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51410; the number is 8 % of the 159 kN dynamic rating. Bore-to-OD planning: OD 110 over bore 50 is a 2.20× step for this size, and the 43 mm height gives a bore/height ratio of 1.16; use these ratios when the housing recess around the 50 mm shaft is the first constraint. Speed band width for this size is 800 r/min between reference and limiting (1.40× ratio); lubrication, preload and heat removal decide where inside that band 51410 can actually run. Rating split for documentation: dynamic 159 kN (L10 life), static 340 kN (safety factor s0), fatigue limit 12.5 kN (adjusted life) — three different uses of three different numbers for 51410, none interchangeable with another. At the printed limiting speed of 2,800 r/min the mean pitch diameter dm ≈ 80.0 mm implies a dn value around 224k mm·r/min; the 2,000 r/min reference speed is the thermal-planning value under catalogue load. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 43 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 159 kN C.",
    "applications": [
      "machine-tool adjustment screws and tailstock centres",
      "low-speed reducer thrust positions",
      "vertical pump and motor shaft thrust"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 50 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The 51410 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 50 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.6; for 51410 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "When the housing seat cannot be machined square to the 50 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51400 bearing.",
      "The 159/340 kN figures belong to 51410 specifically (the single flat pressed steel execution of 51410); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51410-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 50 mm, OD 110 mm, height 43 mm; weight 2000 g. Load figures from SKF 17000: dynamic 159 kN, static 340 kN, fatigue limit 12.5 kN; reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51410 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 10 decodes to 50 mm (code 10 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "Can 51410-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 50 mm shaft must go to a separate radial bearing; mixed loading through 51410 edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51410",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51410-SKF",
      "51410"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51111-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51111",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 78,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 30.2,
    "static_load_kN": 81.5,
    "fatigue_load_limit_kN": 3,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 230,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51111 is a SKF single-direction thrust ball bearing for a 55 mm seat, built to ISO 104, with a flat housing seating surface, 55×78×16 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 11 decodes to 55 mm (code 11 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 55×78×16 mm (2.165×3.071×0.63 in), 11.5 mm radial section, C 30.2 kN, C0 81.5 kN, Pu 3 kN. reference speed 3,800 r/min (thermal) and limiting speed 5,300 r/min (mechanical), catalogue mass 230 g. Light-load floor: Pu = 3 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51111; the number is 10 % of the 30.2 kN dynamic rating. Selection figures for 51111: the C0/C ratio is 2.70, Pu 3 kN is about 10 % of C, and the catalogue mass works out to roughly 4 g per millimetre of bore; the printed minimum-load factor is A 0.039. Mass and section check: 230 g inside the 55×78×16 mm outline leaves a 11.5 mm radial section, and the 81.5 kN static rating is 2.70× the dynamic rating — plan static safety and minimum preload against those figures. Rating split for documentation: dynamic 30.2 kN (L10 life), static 81.5 kN (safety factor s0), fatigue limit 3 kN (adjusted life) — three different uses of three different numbers for 51111, none interchangeable with another. At the printed limiting speed of 5,300 r/min the mean pitch diameter dm ≈ 66.5 mm implies a dn value around 352k mm·r/min; the 3,800 r/min reference speed is the thermal-planning value under catalogue load. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 16 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 30.2 kN C.",
    "applications": [
      "machine-tool adjustment screws and tailstock centres",
      "low-speed reducer thrust positions",
      "screw jacks and press-adjustment spindles"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "false brinelling of the stationary tracks while the machine stands under vibration"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.039; for 51111 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 16 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "When the housing seat cannot be machined square to the 55 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 30.2 kN track before first rotation.",
      "Ordering discipline for 51111: the catalogue page quotes 51111 and its 30.2/81.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51111-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 55 mm, OD 78 mm, height 16 mm; weight 230 g. Load figures from SKF 17000: dynamic 30.2 kN, static 81.5 kN, fatigue limit 3 kN; reference speed 3,800 r/min (thermal) and limiting speed 5,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51111 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 11 decodes to 55 mm (code 11 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "Can 51111-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 55 mm shaft must go to a separate radial bearing; mixed loading through 51111 edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51111",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×78×16 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51111-SKF",
      "51111"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51211-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51211",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 90,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 58.5,
    "static_load_kN": 134,
    "fatigue_load_limit_kN": 4.9,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 590,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51211 is SKF's 55 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 55×90×25 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 11 encode the bore as 55 mm (code 11 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 55×90×25 mm (2.165×3.543×0.984 in), 17.5 mm radial section, C 58.5 kN, C0 134 kN, Pu 4.9 kN. reference speed 2,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 590 g. At the printed limiting speed of 4,000 r/min the mean pitch diameter dm ≈ 72.5 mm implies a dn value around 290k mm·r/min; the 2,800 r/min reference speed is the thermal-planning value under catalogue load. Minimum-load arithmetic: with dm ≈ 72.5 mm and factor A 0.11, Fam ≈ A·(n·dm/1000)² at the 2,800 r/min reference speed is about 4.5 kN for 51211; below that preload the balls skid and smear the tracks. Capacity density: 58.5 kN C from 0.590 kg of bearing steel gives about 99.2 kN per kilogram; static density is correspondingly 227.1 kN/kg at C0 134 kN. Sizing arithmetic on the 55 mm bore: 58.5 kN C over the 17.5 mm radial section gives 3.3 kN per section millimetre, and the 25 mm stack height is 1.43× that section — proportions typical of a 51200 thrust section. Track-circle loading: per millimetre of mean track circumference the 58.5 kN dynamic rating corresponds to roughly 0.26 kN/mm of π·dm track, a useful comparison against the other dimension series of the 55 mm bore. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 25 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 58.5 kN C.",
    "applications": [
      "screw jacks and press-adjustment spindles",
      "machine-tool adjustment screws and tailstock centres",
      "vertical pump and motor shaft thrust"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 58.5 kN track before first rotation.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 58.5/134 kN and the available 90 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51211 against two-way load lifts the loose washer off its raceway.",
      "The 58.5/134 kN figures belong to 51211 specifically (the single flat pressed steel execution of 51211); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51211-SKF?",
        "a": "51211 measures 55 mm bore × 90 mm OD × 25 mm bearing height (2.165 × 3.543 × 0.984 in), mass about 590 g. SKF 17000 ratings: C 58.5 kN, C0 134 kN, Pu 4.9 kN, reference speed 2,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51211 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 11 encode the bore as 55 mm (code 11 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51211-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 55 mm shaft must go to a separate radial bearing; mixed loading through 51211 edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51211",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×90×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51211-SKF",
      "51211"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51311-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51311",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 105,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 101,
    "static_load_kN": 224,
    "fatigue_load_limit_kN": 8.3,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 1300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51311 is an ISO 104 single-direction thrust ball bearing, 55 mm bore and 105 mm OD on a flat housing seat, standing 35 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 11: bore 55 mm (code 11 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 55×105×35 mm (2.165×4.134×1.378 in), 25.0 mm radial section, C 101 kN, C0 224 kN, Pu 8.3 kN. reference speed 2,200 r/min (thermal) and limiting speed 3,200 r/min (mechanical), catalogue mass 1300 g. Load balance: C0 224 kN against C 101 kN gives a 2.22 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 8.3 kN enters the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 2,200 r/min against a 3,200 r/min limiting speed, a reference-to-limit ratio of 0.69. Stack/annulus proportions: the 35 mm axial stack over the 6,283 mm² washer annulus gives 5.57 mm of height per annular square millimetre ×10⁻³, and at 1300 g the bearing holds about 172.3 kN of C0 per kilogram. Pitch-diameter arithmetic: dm = (55+105)/2 = 80.0 mm; at the 3,200 r/min limiting speed that corresponds to roughly 256k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 3,200 r/min while thermal balance under catalogue load sets the 2,200 r/min reference; at dm ≈ 80.0 mm the corresponding dn is approximately 256k mm·r/min. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 35 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 101 kN C.",
    "applications": [
      "screw jacks and press-adjustment spindles",
      "low-speed reducer thrust positions",
      "crane hooks and lifting-block pins"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 35 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "The 51311 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 55 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.26; for 51311 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51311 as the single flat pressed steel execution; other order numbers of the 51311 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51311-SKF?",
        "a": "The catalogue envelope is 55×105×35 mm, mass 1300 g; ratings C 101 kN / C0 224 kN / Pu 8.3 kN, reference speed 2,200 r/min (thermal) and limiting speed 3,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51311 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 11: bore 55 mm (code 11 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51311-SKF?",
        "a": "The 2,200 r/min reference speed is the thermal balance under catalogue load; the 3,200 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51311-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.26 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51311",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×105×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51311-SKF",
      "51311"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51411-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51411",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 48,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 195,
    "static_load_kN": 400,
    "fatigue_load_limit_kN": 14.6,
    "reference_speed_rpm": 1800,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 2550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51411 is SKF's 55 mm-bore single-direction thrust ball bearing in the 51400 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 55×120×48 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 11 encode the bore as 55 mm (code 11 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 55×120×48 mm (2.165×4.724×1.89 in), 32.5 mm radial section, C 195 kN, C0 400 kN, Pu 14.6 kN. reference speed 1,800 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 2550 g. Envelope economics: the 48 mm axial height over a 32.5 mm radial section yields 4.1 kN of dynamic capacity per height millimetre, and the bearing weighs 2550 g for 195 kN C — about 13 g per rated kN. Minimum-load arithmetic: with dm ≈ 87.5 mm and factor A 0.79, Fam ≈ A·(n·dm/1000)² at the 1,800 r/min reference speed is about 19.6 kN for 51411; below that preload the balls skid and smear the tracks. Speed band width for this size is 600 r/min between reference and limiting (1.33× ratio); lubrication, preload and heat removal decide where inside that band 51411 can actually run. Rating split for documentation: dynamic 195 kN (L10 life), static 400 kN (safety factor s0), fatigue limit 14.6 kN (adjusted life) — three different uses of three different numbers for 51411, none interchangeable with another. Light-load floor: Pu = 14.6 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51411; the number is 7 % of the 195 kN dynamic rating. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 48 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 195 kN C.",
    "applications": [
      "machine-tool adjustment screws and tailstock centres",
      "vertical pump and motor shaft thrust",
      "screw jacks and press-adjustment spindles"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "track rust staining from condensate during long idle periods in humid plant air",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 195 kN track before first rotation.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 55 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.79; for 51411 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 195/400 kN figures belong to 51411 specifically (the single flat pressed steel execution of 51411); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51411-SKF?",
        "a": "51411 measures 55 mm bore × 120 mm OD × 48 mm bearing height (2.165 × 4.724 × 1.89 in), mass about 2550 g. SKF 17000 ratings: C 195 kN, C0 400 kN, Pu 14.6 kN, reference speed 1,800 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51411 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 11 encode the bore as 55 mm (code 11 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51411-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.79 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51411",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×120×48 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51411-SKF",
      "51411"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51112-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51112",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 85,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 41.6,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 4.55,
    "reference_speed_rpm": 3600,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 270,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51112 is an ISO 104 single-direction thrust ball bearing, 60 mm bore and 85 mm OD on a flat housing seat, standing 17 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 12: bore 60 mm (code 12 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 60×85×17 mm (2.362×3.346×0.669 in), 12.5 mm radial section, C 41.6 kN, C0 122 kN, Pu 4.55 kN. reference speed 3,600 r/min (thermal) and limiting speed 5,000 r/min (mechanical), catalogue mass 270 g. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.077 at the 5,000 r/min limiting speed raises the required axial preload to about 10.1 kN; the reference-speed value 5.2 kN is the thermal design point. Load balance: C0 122 kN against C 41.6 kN gives a 2.93 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 4.55 kN enters the adjusted-life check. Static-first selection data: 122 kN C0 spread across the 17 mm stack gives 7.2 kN of static rating per height millimetre, and the 270 g mass/C0 ratio is about 2 g per static kN — crane-hook and screw positions are normally sized on these two figures. Rating split for documentation: dynamic 41.6 kN (L10 life), static 122 kN (safety factor s0), fatigue limit 4.55 kN (adjusted life) — three different uses of three different numbers for 51112, none interchangeable with another. Light-load floor: Pu = 4.55 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51112; the number is 11 % of the 41.6 kN dynamic rating. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 60 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 41.6/122 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "vertical motor and pump thrust bearings",
      "heavy crane hooks and hoist blocks",
      "winch drums and reducer housings"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 60 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.077; for 51112 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 51112 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 60 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "When the housing seat cannot be machined square to the 60 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "The 41.6/122 kN figures belong to 51112 specifically (the single flat pressed steel execution of 51112); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51112-SKF?",
        "a": "The catalogue envelope is 60×85×17 mm, mass 270 g; ratings C 41.6 kN / C0 122 kN / Pu 4.55 kN, reference speed 3,600 r/min (thermal) and limiting speed 5,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51112 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 12: bore 60 mm (code 12 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51112-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 60 mm shaft must go to a separate radial bearing; mixed loading through 51112 edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51112",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51112-SKF",
      "51112"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51212-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51212",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 95,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 59.2,
    "static_load_kN": 140,
    "fatigue_load_limit_kN": 5.1,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51212 is SKF's 60 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 60×95×26 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 12 encode the bore as 60 mm (code 12 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 60×95×26 mm (2.362×3.74×1.024 in), 17.5 mm radial section, C 59.2 kN, C0 140 kN, Pu 5.1 kN. reference speed 2,800 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 650 g. Load balance: C0 140 kN against C 59.2 kN gives a 2.36 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 5.1 kN enters the adjusted-life check. Selection figures for 51212: the C0/C ratio is 2.36, Pu 5.1 kN is about 9 % of C, and the catalogue mass works out to roughly 11 g per millimetre of bore; the printed minimum-load factor is A 0.12. Light-load floor: Pu = 5.1 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51212; the number is 9 % of the 59.2 kN dynamic rating. Mass and section check: 650 g inside the 60×95×26 mm outline leaves a 17.5 mm radial section, and the 140 kN static rating is 2.36× the dynamic rating — plan static safety and minimum preload against those figures. Envelope economics: the 26 mm axial height over a 17.5 mm radial section yields 2.3 kN of dynamic capacity per height millimetre, and the bearing weighs 650 g for 59.2 kN C — about 11 g per rated kN. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 26 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 59.2 kN C.",
    "applications": [
      "heavy crane hooks and hoist blocks",
      "large screw jacks and press rams",
      "turret and slewing-bearing adjustment screws"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "track rust staining from condensate during long idle periods in humid plant air"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51212 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 60 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 60 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51212 as the single flat pressed steel execution; other order numbers of the 51212 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51212-SKF?",
        "a": "51212 measures 60 mm bore × 95 mm OD × 26 mm bearing height (2.362 × 3.74 × 1.024 in), mass about 650 g. SKF 17000 ratings: C 59.2 kN, C0 140 kN, Pu 5.1 kN, reference speed 2,800 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51212 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 12 encode the bore as 60 mm (code 12 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "Can 51212-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 60 mm shaft must go to a separate radial bearing; mixed loading through 51212 edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51212",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×95×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51212-SKF",
      "51212"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51312-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51312",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 101,
    "static_load_kN": 224,
    "fatigue_load_limit_kN": 8.3,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 1350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51300 series order number 51312 is a SKF single-direction thrust ball bearing for a 60 mm seat, built to ISO 104, with a flat housing seating surface, 60×110×35 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 12 decodes to 60 mm (code 12 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 60×110×35 mm (2.362×4.331×1.378 in), 25.0 mm radial section, C 101 kN, C0 224 kN, Pu 8.3 kN. reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 1350 g. Track-circle loading: per millimetre of mean track circumference the 101 kN dynamic rating corresponds to roughly 0.38 kN/mm of π·dm track, a useful comparison against the other dimension series of the 60 mm bore. Pitch-diameter arithmetic: dm = (60+110)/2 = 85.0 mm; at the 3,000 r/min limiting speed that corresponds to roughly 255k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Mass and section check: 1350 g inside the 60×110×35 mm outline leaves a 25.0 mm radial section, and the 224 kN static rating is 2.22× the dynamic rating — plan static safety and minimum preload against those figures. Load balance: C0 224 kN against C 101 kN gives a 2.22 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 8.3 kN enters the adjusted-life check. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51312 covers about 6,676 mm², distributing C0 224 kN over a mean track circle of π·dm ≈ 267 mm. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 35 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 101 kN C.",
    "applications": [
      "turret and slewing-bearing adjustment screws",
      "large screw jacks and press rams",
      "vertical motor and pump thrust bearings"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The 51312 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 60 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 101 kN track before first rotation.",
      "When the housing seat cannot be machined square to the 60 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51300 bearing.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 35 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51312 as the single flat pressed steel execution; other order numbers of the 51312 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51312-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 60 mm, OD 110 mm, height 35 mm; weight 1350 g. Load figures from SKF 17000: dynamic 101 kN, static 224 kN, fatigue limit 8.3 kN; reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51312 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 12 decodes to 60 mm (code 12 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51312-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 3,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 60 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51312",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×110×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51312-SKF",
      "51312"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51412-M",
    "brand": "SKF",
    "manufacturer_designation": "51412 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 51,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 199,
    "static_load_kN": 430,
    "fatigue_load_limit_kN": 16,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 3100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51400 series order number 51412 M is a SKF single-direction thrust ball bearing for a 60 mm seat, built to ISO 104, with a flat housing seating surface, 60×130×51 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 12 decodes to 60 mm (code 12 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 60×130×51 mm (2.362×5.118×2.008 in), 35.0 mm radial section, C 199 kN, C0 430 kN, Pu 16 kN. reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 3100 g. Load balance: C0 430 kN against C 199 kN gives a 2.16 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 16 kN enters the adjusted-life check. Envelope economics: the 51 mm axial height over a 35.0 mm radial section yields 3.9 kN of dynamic capacity per height millimetre, and the bearing weighs 3100 g for 199 kN C — about 16 g per rated kN. Sizing arithmetic on the 60 mm bore: 199 kN C over the 35.0 mm radial section gives 5.7 kN per section millimetre, and the 51 mm stack height is 1.46× that section — proportions typical of a 51400 thrust section. Speed band width for this size is 600 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 51412 M can actually run. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51412 M covers about 10,446 mm², distributing C0 430 kN over a mean track circle of π·dm ≈ 298 mm. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 3100 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 60 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "heavy crane hooks and hoist blocks",
      "winch drums and reducer housings",
      "turret and slewing-bearing adjustment screws"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 60 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51400 bearing.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 60 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 51 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Ordering discipline for 51412: the catalogue page quotes 51412 M and its 199/430 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51412-M?",
        "a": "Boundary dimensions to ISO 104: bore 60 mm, OD 130 mm, height 51 mm; weight 3100 g. Load figures from SKF 17000: dynamic 199 kN, static 430 kN, fatigue limit 16 kN; reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51412 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 12 decodes to 60 mm (code 12 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 60 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51412 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51412",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51412-M",
      "51412 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51113-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51113",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 90,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 37.7,
    "static_load_kN": 108,
    "fatigue_load_limit_kN": 4,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 330,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51113 is a SKF single-direction thrust ball bearing for a 65 mm seat, built to ISO 104, with a flat housing seating surface, 65×90×18 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 13 decodes to 65 mm (code 13 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 65×90×18 mm (2.559×3.543×0.709 in), 12.5 mm radial section, C 37.7 kN, C0 108 kN, Pu 4 kN. reference speed 3,400 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 330 g. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51113 covers about 3,043 mm², distributing C0 108 kN over a mean track circle of π·dm ≈ 243 mm. Envelope economics: the 18 mm axial height over a 12.5 mm radial section yields 2.1 kN of dynamic capacity per height millimetre, and the bearing weighs 330 g for 37.7 kN C — about 9 g per rated kN. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 4,800 r/min while thermal balance under catalogue load sets the 3,400 r/min reference; at dm ≈ 77.5 mm the corresponding dn is approximately 372k mm·r/min. Load balance: C0 108 kN against C 37.7 kN gives a 2.86 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 4 kN enters the adjusted-life check. Bore-to-OD planning: OD 90 over bore 65 is a 1.38× step for this size, and the 18 mm height gives a bore/height ratio of 3.61; use these ratios when the housing recess around the 65 mm shaft is the first constraint. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 65 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 37.7/108 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "heavy crane hooks and hoist blocks",
      "winch drums and reducer housings",
      "large screw jacks and press rams"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The 51113 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 65 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 37.7/108 kN and the available 90 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "When the housing seat cannot be machined square to the 65 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51113 as the single flat pressed steel execution; other order numbers of the 51113 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51113-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 65 mm, OD 90 mm, height 18 mm; weight 330 g. Load figures from SKF 17000: dynamic 37.7 kN, static 108 kN, fatigue limit 4 kN; reference speed 3,400 r/min (thermal) and limiting speed 4,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51113 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 13 decodes to 65 mm (code 13 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51113-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 4,800 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51113",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51113-SKF",
      "51113"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51213-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51213",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 100,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 60.5,
    "static_load_kN": 150,
    "fatigue_load_limit_kN": 5.5,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 720,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51213 is a SKF single-direction thrust ball bearing for a 65 mm seat, built to ISO 104, with a flat housing seating surface, 65×100×27 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 13 decodes to 65 mm (code 13 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 65×100×27 mm (2.559×3.937×1.063 in), 17.5 mm radial section, C 60.5 kN, C0 150 kN, Pu 5.5 kN. reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 720 g. Speed band width for this size is 1,000 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 51213 can actually run. Capacity density: 60.5 kN C from 0.720 kg of bearing steel gives about 84.0 kN per kilogram; static density is correspondingly 208.3 kN/kg at C0 150 kN. Selection figures for 51213: the C0/C ratio is 2.48, Pu 5.5 kN is about 9 % of C, and the catalogue mass works out to roughly 11 g per millimetre of bore; the printed minimum-load factor is A 0.14. Sizing arithmetic on the 65 mm bore: 60.5 kN C over the 17.5 mm radial section gives 3.5 kN per section millimetre, and the 27 mm stack height is 1.54× that section — proportions typical of a 51200 thrust section. Light-load floor: Pu = 5.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51213; the number is 9 % of the 60.5 kN dynamic rating. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 65 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 60.5/150 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "turret and slewing-bearing adjustment screws",
      "large screw jacks and press rams",
      "vertical motor and pump thrust bearings"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "track rust staining from condensate during long idle periods in humid plant air",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 27 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The 51213 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 65 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "When the housing seat cannot be machined square to the 65 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 60.5/150 kN and the available 100 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51213 as the single flat pressed steel execution; other order numbers of the 51213 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51213-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 65 mm, OD 100 mm, height 27 mm; weight 720 g. Load figures from SKF 17000: dynamic 60.5 kN, static 150 kN, fatigue limit 5.5 kN; reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51213 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 13 decodes to 65 mm (code 13 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51213-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.14 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51213",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×100×27 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51213-SKF",
      "51213"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51313-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51313",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 115,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 106,
    "static_load_kN": 240,
    "fatigue_load_limit_kN": 8.8,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 1500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51313 is SKF's 65 mm-bore single-direction thrust ball bearing in the 51300 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 65×115×36 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 13 encode the bore as 65 mm (code 13 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 65×115×36 mm (2.559×4.528×1.417 in), 25.0 mm radial section, C 106 kN, C0 240 kN, Pu 8.8 kN. reference speed 2,000 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 1500 g. Bore-to-OD planning: OD 115 over bore 65 is a 1.77× step for this size, and the 36 mm height gives a bore/height ratio of 1.81; use these ratios when the housing recess around the 65 mm shaft is the first constraint. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51313 covers about 7,069 mm², distributing C0 240 kN over a mean track circle of π·dm ≈ 283 mm. Load balance: C0 240 kN against C 106 kN gives a 2.26 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 8.8 kN enters the adjusted-life check. Selection figures for 51313: the C0/C ratio is 2.26, Pu 8.8 kN is about 8 % of C, and the catalogue mass works out to roughly 23 g per millimetre of bore; the printed minimum-load factor is A 0.3. Mass and section check: 1500 g inside the 65×115×36 mm outline leaves a 25.0 mm radial section, and the 240 kN static rating is 2.26× the dynamic rating — plan static safety and minimum preload against those figures. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 65 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 106/240 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "winch drums and reducer housings",
      "vertical motor and pump thrust bearings",
      "large screw jacks and press rams"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 106 kN track before first rotation.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 65 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 106/240 kN and the available 115 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 106/240 kN figures belong to 51313 specifically (the single flat pressed steel execution of 51313); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51313-SKF?",
        "a": "51313 measures 65 mm bore × 115 mm OD × 36 mm bearing height (2.559 × 4.528 × 1.417 in), mass about 1500 g. SKF 17000 ratings: C 106 kN, C0 240 kN, Pu 8.8 kN, reference speed 2,000 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51313 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 13 encode the bore as 65 mm (code 13 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 65 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51313 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51313",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×115×36 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51313-SKF",
      "51313"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51413-M",
    "brand": "SKF",
    "manufacturer_designation": "51413 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 56,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 216,
    "static_load_kN": 490,
    "fatigue_load_limit_kN": 18,
    "reference_speed_rpm": 1500,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 4000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51400 series order number 51413 M is a SKF single-direction thrust ball bearing for a 65 mm seat, built to ISO 104, with a flat housing seating surface, 65×140×56 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 13 decodes to 65 mm (code 13 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 65×140×56 mm (2.559×5.512×2.205 in), 37.5 mm radial section, C 216 kN, C0 490 kN, Pu 18 kN. reference speed 1,500 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 4000 g. Mass and section check: 4000 g inside the 65×140×56 mm outline leaves a 37.5 mm radial section, and the 490 kN static rating is 2.27× the dynamic rating — plan static safety and minimum preload against those figures. Stack/annulus proportions: the 56 mm axial stack over the 12,075 mm² washer annulus gives 4.64 mm of height per annular square millimetre ×10⁻³, and at 4000 g the bearing holds about 122.5 kN of C0 per kilogram. Section proportions: the 37.5 mm radial section compares with 65 mm of bore (section/bore ≈ 0.58) and the 56 mm height is 1.49× that section — the proportions that identify the 51400 envelope at a glance. Sizing arithmetic on the 65 mm bore: 216 kN C over the 37.5 mm radial section gives 5.8 kN per section millimetre, and the 56 mm stack height is 1.49× that section — proportions typical of a 51400 thrust section. Rating split for documentation: dynamic 216 kN (L10 life), static 490 kN (safety factor s0), fatigue limit 18 kN (adjusted life) — three different uses of three different numbers for 51413 M, none interchangeable with another. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51413 M adds a small amount of mass and cage strength without changing the 65×140×56 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 2,200 r/min ceiling.",
    "applications": [
      "vertical motor and pump thrust bearings",
      "heavy crane hooks and hoist blocks",
      "winch drums and reducer housings"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The 51413 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 65 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 216/490 kN and the available 140 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "When the housing seat cannot be machined square to the 65 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51400 bearing.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51413 M as the single flat brass execution; other order numbers of the 51413 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51413-M?",
        "a": "Boundary dimensions to ISO 104: bore 65 mm, OD 140 mm, height 56 mm; weight 4000 g. Load figures from SKF 17000: dynamic 216 kN, static 490 kN, fatigue limit 18 kN; reference speed 1,500 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51413 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 13 decodes to 65 mm (code 13 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51413-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 1.2 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, M-cage product) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51413",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51413-M",
      "51413 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51114-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51114",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 95,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 40.3,
    "static_load_kN": 120,
    "fatigue_load_limit_kN": 4.4,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51114 is a SKF single-direction thrust ball bearing for a 70 mm seat, built to ISO 104, with a flat housing seating surface, 70×95×18 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 14 decodes to 70 mm (code 14 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 70×95×18 mm (2.756×3.74×0.709 in), 12.5 mm radial section, C 40.3 kN, C0 120 kN, Pu 4.4 kN. reference speed 3,400 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 350 g. Stack/annulus proportions: the 18 mm axial stack over the 3,240 mm² washer annulus gives 5.56 mm of height per annular square millimetre ×10⁻³, and at 350 g the bearing holds about 342.9 kN of C0 per kilogram. Pitch-diameter arithmetic: dm = (70+95)/2 = 82.5 mm; at the 4,500 r/min limiting speed that corresponds to roughly 371k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. At the printed limiting speed of 4,500 r/min the mean pitch diameter dm ≈ 82.5 mm implies a dn value around 371k mm·r/min; the 3,400 r/min reference speed is the thermal-planning value under catalogue load. Sizing arithmetic on the 70 mm bore: 40.3 kN C over the 12.5 mm radial section gives 3.2 kN per section millimetre, and the 18 mm stack height is 1.44× that section — proportions typical of a 51100 thrust section. Load balance: C0 120 kN against C 40.3 kN gives a 2.98 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 4.4 kN enters the adjusted-life check. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 70 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 40.3/120 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "vertical motor and pump thrust bearings",
      "heavy crane hooks and hoist blocks",
      "large screw jacks and press rams"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 70 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.074; for 51114 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "When the housing seat cannot be machined square to the 70 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 18 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The 40.3/120 kN figures belong to 51114 specifically (the single flat pressed steel execution of 51114); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51114-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 70 mm, OD 95 mm, height 18 mm; weight 350 g. Load figures from SKF 17000: dynamic 40.3 kN, static 120 kN, fatigue limit 4.4 kN; reference speed 3,400 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51114 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 14 decodes to 70 mm (code 14 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51114-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 4,500 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 70 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51114",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51114-SKF",
      "51114"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51214-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51214",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 105,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 62.4,
    "static_load_kN": 160,
    "fatigue_load_limit_kN": 5.85,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 790,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51214 is a SKF single-direction thrust ball bearing for a 70 mm seat, built to ISO 104, with a flat housing seating surface, 70×105×27 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 14 decodes to 70 mm (code 14 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 70×105×27 mm (2.756×4.134×1.063 in), 17.5 mm radial section, C 62.4 kN, C0 160 kN, Pu 5.85 kN. reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 790 g. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51214 covers about 4,811 mm², distributing C0 160 kN over a mean track circle of π·dm ≈ 275 mm. Track-circle loading: per millimetre of mean track circumference the 62.4 kN dynamic rating corresponds to roughly 0.23 kN/mm of π·dm track, a useful comparison against the other dimension series of the 70 mm bore. Bore-to-OD planning: OD 105 over bore 70 is a 1.50× step for this size, and the 27 mm height gives a bore/height ratio of 2.59; use these ratios when the housing recess around the 70 mm shaft is the first constraint. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.16 at the 3,600 r/min limiting speed raises the required axial preload to about 15.9 kN; the reference-speed value 8.3 kN is the thermal design point. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 3,600 r/min while thermal balance under catalogue load sets the 2,600 r/min reference; at dm ≈ 87.5 mm the corresponding dn is approximately 315k mm·r/min. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 70 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 62.4/160 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "large screw jacks and press rams",
      "winch drums and reducer housings",
      "turret and slewing-bearing adjustment screws"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "false brinelling of the stationary tracks while the machine stands under vibration"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51214 against two-way load lifts the loose washer off its raceway.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.16; for 51214 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 62.4/160 kN and the available 105 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51214 as the single flat pressed steel execution; other order numbers of the 51214 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51214-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 70 mm, OD 105 mm, height 27 mm; weight 790 g. Load figures from SKF 17000: dynamic 62.4 kN, static 160 kN, fatigue limit 5.85 kN; reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51214 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 14 decodes to 70 mm (code 14 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51214-SKF?",
        "a": "The 2,600 r/min reference speed is the thermal balance under catalogue load; the 3,600 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51214-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.16 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51214",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 70×105×27 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "53214",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×105×27 mm ISO 104 thrust-ball envelope with catalogue ratings within 10 %; 53214 is the single-direction, sphered housing washer with U 214 seat washer, stamped sheet-steel cage execution of this size — boundary dimensions interchangeable, execution differs. The counterpart is a sphered execution that needs its U 214 seat washer; its mounted H1 is taller than the bearing height."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51214-SKF",
      "51214"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51314-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51314",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 135,
    "static_load_kN": 320,
    "fatigue_load_limit_kN": 11.8,
    "reference_speed_rpm": 1900,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 2000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51300 series order number 51314 is a SKF single-direction thrust ball bearing for a 70 mm seat, built to ISO 104, with a flat housing seating surface, 70×125×40 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 14 decodes to 70 mm (code 14 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 70×125×40 mm (2.756×4.921×1.575 in), 27.5 mm radial section, C 135 kN, C0 320 kN, Pu 11.8 kN. reference speed 1,900 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 2000 g. Bore-to-OD planning: OD 125 over bore 70 is a 1.79× step for this size, and the 40 mm height gives a bore/height ratio of 1.75; use these ratios when the housing recess around the 70 mm shaft is the first constraint. Light-load floor: Pu = 11.8 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51314; the number is 9 % of the 135 kN dynamic rating. Pitch-diameter arithmetic: dm = (70+125)/2 = 97.5 mm; at the 2,600 r/min limiting speed that corresponds to roughly 254k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Capacity density: 135 kN C from 2.000 kg of bearing steel gives about 67.5 kN per kilogram; static density is correspondingly 160.0 kN/kg at C0 320 kN. Stack/annulus proportions: the 40 mm axial stack over the 8,423 mm² washer annulus gives 4.75 mm of height per annular square millimetre ×10⁻³, and at 2000 g the bearing holds about 160.0 kN of C0 per kilogram. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 40 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 135 kN C.",
    "applications": [
      "large screw jacks and press rams",
      "vertical motor and pump thrust bearings",
      "turret and slewing-bearing adjustment screws"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 135 kN track before first rotation.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 40 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "When the housing seat cannot be machined square to the 70 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51300 bearing.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51314 against two-way load lifts the loose washer off its raceway.",
      "The 135/320 kN figures belong to 51314 specifically (the single flat pressed steel execution of 51314); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51314-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 70 mm, OD 125 mm, height 40 mm; weight 2000 g. Load figures from SKF 17000: dynamic 135 kN, static 320 kN, fatigue limit 11.8 kN; reference speed 1,900 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51314 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 14 decodes to 70 mm (code 14 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51314-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 70 mm shaft must go to a separate radial bearing; mixed loading through 51314 edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51314",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51314-SKF",
      "51314"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51414-M",
    "brand": "SKF",
    "manufacturer_designation": "51414 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 60,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 234,
    "static_load_kN": 550,
    "fatigue_load_limit_kN": 19.3,
    "reference_speed_rpm": 1400,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "weight_g": 5000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51400 series order number 51414 M is a SKF single-direction thrust ball bearing for a 70 mm seat, built to ISO 104, with a flat housing seating surface, 70×150×60 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 14 decodes to 70 mm (code 14 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 70×150×60 mm (2.756×5.906×2.362 in), 40.0 mm radial section, C 234 kN, C0 550 kN, Pu 19.3 kN. reference speed 1,400 r/min (thermal) and limiting speed 2,000 r/min (mechanical), catalogue mass 5000 g. Track-circle loading: per millimetre of mean track circumference the 234 kN dynamic rating corresponds to roughly 0.68 kN/mm of π·dm track, a useful comparison against the other dimension series of the 70 mm bore. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51414 M covers about 13,823 mm², distributing C0 550 kN over a mean track circle of π·dm ≈ 346 mm. Section proportions: the 40.0 mm radial section compares with 70 mm of bore (section/bore ≈ 0.57) and the 60 mm height is 1.50× that section — the proportions that identify the 51400 envelope at a glance. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 1.6 at the 2,000 r/min limiting speed raises the required axial preload to about 77.4 kN; the reference-speed value 37.9 kN is the thermal design point. Speed band width for this size is 600 r/min between reference and limiting (1.43× ratio); lubrication, preload and heat removal decide where inside that band 51414 M can actually run. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51414 M adds a small amount of mass and cage strength without changing the 70×150×60 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 2,000 r/min ceiling.",
    "applications": [
      "turret and slewing-bearing adjustment screws",
      "large screw jacks and press rams",
      "heavy crane hooks and hoist blocks"
    ],
    "failure_modes": [
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "washer face scoring from swarf trapped between the loose housing washer and its register"
    ],
    "pitfalls": [
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 70 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 1.6; for 51414 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "When the housing seat cannot be machined square to the 70 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51400 bearing.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 60 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The 234/550 kN figures belong to 51414 M specifically (the single flat brass execution of 51414); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51414-M?",
        "a": "Boundary dimensions to ISO 104: bore 70 mm, OD 150 mm, height 60 mm; weight 5000 g. Load figures from SKF 17000: dynamic 234 kN, static 550 kN, fatigue limit 19.3 kN; reference speed 1,400 r/min (thermal) and limiting speed 2,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51414 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 14 decodes to 70 mm (code 14 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51414-M lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 2,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51414",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51414-M",
      "51414 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51115-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51115",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 75,
    "D_mm": 100,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 44.2,
    "static_load_kN": 134,
    "fatigue_load_limit_kN": 4.9,
    "reference_speed_rpm": 3200,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51115 is an ISO 104 single-direction thrust ball bearing, 75 mm bore and 100 mm OD on a flat housing seat, standing 19 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 15: bore 75 mm (code 15 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 75×100×19 mm (2.953×3.937×0.748 in), 12.5 mm radial section, C 44.2 kN, C0 134 kN, Pu 4.9 kN. reference speed 3,200 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 400 g. Load balance: C0 134 kN against C 44.2 kN gives a 3.03 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 4.9 kN enters the adjusted-life check. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 4,300 r/min while thermal balance under catalogue load sets the 3,200 r/min reference; at dm ≈ 87.5 mm the corresponding dn is approximately 376k mm·r/min. Capacity density: 44.2 kN C from 0.400 kg of bearing steel gives about 110.5 kN per kilogram; static density is correspondingly 335.0 kN/kg at C0 134 kN. Mass and section check: 400 g inside the 75×100×19 mm outline leaves a 12.5 mm radial section, and the 134 kN static rating is 3.03× the dynamic rating — plan static safety and minimum preload against those figures. Envelope economics: the 19 mm axial height over a 12.5 mm radial section yields 2.3 kN of dynamic capacity per height millimetre, and the bearing weighs 400 g for 44.2 kN C — about 9 g per rated kN. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 19 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 44.2 kN C.",
    "applications": [
      "vertical motor and pump thrust bearings",
      "turret and slewing-bearing adjustment screws",
      "winch drums and reducer housings"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 19 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 44.2 kN track before first rotation.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.11; for 51115 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 44.2/134 kN figures belong to 51115 specifically (the single flat pressed steel execution of 51115); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51115-SKF?",
        "a": "The catalogue envelope is 75×100×19 mm, mass 400 g; ratings C 44.2 kN / C0 134 kN / Pu 4.9 kN, reference speed 3,200 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51115 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 15: bore 75 mm (code 15 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 75 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51115 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51115",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51115-SKF",
      "51115"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51215-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51215",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 75,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 63.7,
    "static_load_kN": 170,
    "fatigue_load_limit_kN": 6.2,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 830,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51215 is an ISO 104 single-direction thrust ball bearing, 75 mm bore and 110 mm OD on a flat housing seat, standing 27 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 15: bore 75 mm (code 15 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 75×110×27 mm (2.953×4.331×1.063 in), 17.5 mm radial section, C 63.7 kN, C0 170 kN, Pu 6.2 kN. reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 830 g. Envelope economics: the 27 mm axial height over a 17.5 mm radial section yields 2.4 kN of dynamic capacity per height millimetre, and the bearing weighs 830 g for 63.7 kN C — about 13 g per rated kN. Mass and section check: 830 g inside the 75×110×27 mm outline leaves a 17.5 mm radial section, and the 170 kN static rating is 2.67× the dynamic rating — plan static safety and minimum preload against those figures. Pitch-diameter arithmetic: dm = (75+110)/2 = 92.5 mm; at the 3,400 r/min limiting speed that corresponds to roughly 315k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Load balance: C0 170 kN against C 63.7 kN gives a 2.67 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 6.2 kN enters the adjusted-life check. Bore-to-OD planning: OD 110 over bore 75 is a 1.47× step for this size, and the 27 mm height gives a bore/height ratio of 2.78; use these ratios when the housing recess around the 75 mm shaft is the first constraint. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 27 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 63.7 kN C.",
    "applications": [
      "winch drums and reducer housings",
      "vertical motor and pump thrust bearings",
      "large screw jacks and press rams"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 75 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 63.7 kN track before first rotation.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 27 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 63.7/170 kN and the available 110 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Ordering discipline for 51215: the catalogue page quotes 51215 and its 63.7/170 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51215-SKF?",
        "a": "The catalogue envelope is 75×110×27 mm, mass 830 g; ratings C 63.7 kN / C0 170 kN / Pu 6.2 kN, reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51215 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 15: bore 75 mm (code 15 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51215 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51215-SKF?",
        "a": "The 2,400 r/min reference speed is the thermal balance under catalogue load; the 3,400 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51215",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×110×27 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51215-SKF",
      "51215"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51315-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51315",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 75,
    "D_mm": 135,
    "B_mm": 44,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 163,
    "static_load_kN": 390,
    "fatigue_load_limit_kN": 14,
    "reference_speed_rpm": 1700,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 2600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51315 is an ISO 104 single-direction thrust ball bearing, 75 mm bore and 135 mm OD on a flat housing seat, standing 44 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 15: bore 75 mm (code 15 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 75×135×44 mm (2.953×5.315×1.732 in), 30.0 mm radial section, C 163 kN, C0 390 kN, Pu 14 kN. reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 2600 g. Light-load floor: Pu = 14 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51315; the number is 9 % of the 163 kN dynamic rating. Section proportions: the 30.0 mm radial section compares with 75 mm of bore (section/bore ≈ 0.40) and the 44 mm height is 1.47× that section — the proportions that identify the 51300 envelope at a glance. Sizing arithmetic on the 75 mm bore: 163 kN C over the 30.0 mm radial section gives 5.4 kN per section millimetre, and the 44 mm stack height is 1.47× that section — proportions typical of a 51300 thrust section. Speed-ratio note for this exact unit: the reference speed is 1,700 r/min against a 2,400 r/min limiting speed, a reference-to-limit ratio of 0.71. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.79 at the 2,400 r/min limiting speed raises the required axial preload to about 50.2 kN; the reference-speed value 25.2 kN is the thermal design point. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 44 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 163 kN C.",
    "applications": [
      "winch drums and reducer housings",
      "large screw jacks and press rams",
      "turret and slewing-bearing adjustment screws"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.79; for 51315 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51315 against two-way load lifts the loose washer off its raceway.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 44 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Ordering discipline for 51315: the catalogue page quotes 51315 and its 163/390 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51315-SKF?",
        "a": "The catalogue envelope is 75×135×44 mm, mass 2600 g; ratings C 163 kN / C0 390 kN / Pu 14 kN, reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51315 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 15: bore 75 mm (code 15 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51315-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 2,400 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51315",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51315-SKF",
      "51315"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51415-M",
    "brand": "SKF",
    "manufacturer_designation": "51415 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 251,
    "static_load_kN": 610,
    "fatigue_load_limit_kN": 20.8,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "weight_g": 6750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51415 M is SKF's 75 mm-bore single-direction thrust ball bearing in the 51400 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 75×160×65 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 15 encode the bore as 75 mm (code 15 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 75×160×65 mm (2.953×6.299×2.559 in), 42.5 mm radial section, C 251 kN, C0 610 kN, Pu 20.8 kN. reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical), catalogue mass 6750 g. Sizing arithmetic on the 75 mm bore: 251 kN C over the 42.5 mm radial section gives 5.9 kN per section millimetre, and the 65 mm stack height is 1.53× that section — proportions typical of a 51400 thrust section. Stack/annulus proportions: the 65 mm axial stack over the 15,688 mm² washer annulus gives 4.14 mm of height per annular square millimetre ×10⁻³, and at 6750 g the bearing holds about 90.4 kN of C0 per kilogram. Speed planning separates the two ceilings mechanically: the pressed brass cage and balls tolerate 1,800 r/min while thermal balance under catalogue load sets the 1,300 r/min reference; at dm ≈ 117.5 mm the corresponding dn is approximately 212k mm·r/min. Light-load floor: Pu = 20.8 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51415 M; the number is 8 % of the 251 kN dynamic rating. Minimum-load arithmetic: with dm ≈ 117.5 mm and factor A 1.9, Fam ≈ A·(n·dm/1000)² at the 1,300 r/min reference speed is about 44.3 kN for 51415 M; below that preload the balls skid and smear the tracks. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51415 M adds a small amount of mass and cage strength without changing the 75×160×65 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,800 r/min ceiling.",
    "applications": [
      "winch drums and reducer housings",
      "vertical motor and pump thrust bearings",
      "heavy crane hooks and hoist blocks"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 75 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51400 bearing.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 251/610 kN and the available 160 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 251 kN track before first rotation.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51415 against two-way load lifts the loose washer off its raceway.",
      "Ordering discipline for 51415: the catalogue page quotes 51415 M and its 251/610 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51415-M?",
        "a": "51415 M measures 75 mm bore × 160 mm OD × 65 mm bearing height (2.953 × 6.299 × 2.559 in), mass about 6750 g. SKF 17000 ratings: C 251 kN, C0 610 kN, Pu 20.8 kN, reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51415 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 15 encode the bore as 75 mm (code 15 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51415 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51415-M?",
        "a": "The 1,300 r/min reference speed is the thermal balance under catalogue load; the 1,800 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51415",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51415-M",
      "51415 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51116-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51116",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 80,
    "D_mm": 105,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 44.9,
    "static_load_kN": 140,
    "fatigue_load_limit_kN": 5.1,
    "reference_speed_rpm": 3000,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51116 is an ISO 104 single-direction thrust ball bearing, 80 mm bore and 105 mm OD on a flat housing seat, standing 19 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 16: bore 80 mm (code 16 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 80×105×19 mm (3.15×4.134×0.748 in), 12.5 mm radial section, C 44.9 kN, C0 140 kN, Pu 5.1 kN. reference speed 3,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 420 g. Static-first selection data: 140 kN C0 spread across the 19 mm stack gives 7.4 kN of static rating per height millimetre, and the 420 g mass/C0 ratio is about 3 g per static kN — crane-hook and screw positions are normally sized on these two figures. Speed band width for this size is 1,300 r/min between reference and limiting (1.43× ratio); lubrication, preload and heat removal decide where inside that band 51116 can actually run. Capacity density: 44.9 kN C from 0.420 kg of bearing steel gives about 106.9 kN per kilogram; static density is correspondingly 333.3 kN/kg at C0 140 kN. Mass and section check: 420 g inside the 80×105×19 mm outline leaves a 12.5 mm radial section, and the 140 kN static rating is 3.12× the dynamic rating — plan static safety and minimum preload against those figures. Stack/annulus proportions: the 19 mm axial stack over the 3,632 mm² washer annulus gives 5.23 mm of height per annular square millimetre ×10⁻³, and at 420 g the bearing holds about 333.3 kN of C0 per kilogram. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 19 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 44.9 kN C.",
    "applications": [
      "turret and slewing-bearing adjustment screws",
      "heavy crane hooks and hoist blocks",
      "vertical motor and pump thrust bearings"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 80 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 44.9 kN track before first rotation.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51116 against two-way load lifts the loose washer off its raceway.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 44.9/140 kN and the available 105 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Ordering discipline for 51116: the catalogue page quotes 51116 and its 44.9/140 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51116-SKF?",
        "a": "The catalogue envelope is 80×105×19 mm, mass 420 g; ratings C 44.9 kN / C0 140 kN / Pu 5.1 kN, reference speed 3,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51116 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 16: bore 80 mm (code 16 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51116 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51116-SKF?",
        "a": "The 3,000 r/min reference speed is the thermal balance under catalogue load; the 4,300 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51116",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51116-SKF",
      "51116"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51216-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51216",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 80,
    "D_mm": 115,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 76.1,
    "static_load_kN": 208,
    "fatigue_load_limit_kN": 7.65,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 910,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51216 is a SKF single-direction thrust ball bearing for a 80 mm seat, built to ISO 104, with a flat housing seating surface, 80×115×28 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 16 decodes to 80 mm (code 16 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 80×115×28 mm (3.15×4.528×1.102 in), 17.5 mm radial section, C 76.1 kN, C0 208 kN, Pu 7.65 kN. reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 910 g. Rating split for documentation: dynamic 76.1 kN (L10 life), static 208 kN (safety factor s0), fatigue limit 7.65 kN (adjusted life) — three different uses of three different numbers for 51216, none interchangeable with another. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51216 covers about 5,360 mm², distributing C0 208 kN over a mean track circle of π·dm ≈ 306 mm. Sizing arithmetic on the 80 mm bore: 76.1 kN C over the 17.5 mm radial section gives 4.3 kN per section millimetre, and the 28 mm stack height is 1.60× that section — proportions typical of a 51200 thrust section. Load balance: C0 208 kN against C 76.1 kN gives a 2.73 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 7.65 kN enters the adjusted-life check. Static-first selection data: 208 kN C0 spread across the 28 mm stack gives 7.4 kN of static rating per height millimetre, and the 910 g mass/C0 ratio is about 4 g per static kN — crane-hook and screw positions are normally sized on these two figures. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 28 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 76.1 kN C.",
    "applications": [
      "vertical motor and pump thrust bearings",
      "turret and slewing-bearing adjustment screws",
      "winch drums and reducer housings"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 28 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 76.1/208 kN and the available 115 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.22; for 51216 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51216 as the single flat pressed steel execution; other order numbers of the 51216 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51216-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 80 mm, OD 115 mm, height 28 mm; weight 910 g. Load figures from SKF 17000: dynamic 76.1 kN, static 208 kN, fatigue limit 7.65 kN; reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51216 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 16 decodes to 80 mm (code 16 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 80 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51216 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51216",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51216-SKF",
      "51216"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51316-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51316",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 44,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 159,
    "static_load_kN": 390,
    "fatigue_load_limit_kN": 13.7,
    "reference_speed_rpm": 1700,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 2700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51300 series order number 51316 is a SKF single-direction thrust ball bearing for a 80 mm seat, built to ISO 104, with a flat housing seating surface, 80×140×44 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 16 decodes to 80 mm (code 16 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 80×140×44 mm (3.15×5.512×1.732 in), 30.0 mm radial section, C 159 kN, C0 390 kN, Pu 13.7 kN. reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 2700 g. Pitch-diameter arithmetic: dm = (80+140)/2 = 110.0 mm; at the 2,400 r/min limiting speed that corresponds to roughly 264k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Sizing arithmetic on the 80 mm bore: 159 kN C over the 30.0 mm radial section gives 5.3 kN per section millimetre, and the 44 mm stack height is 1.47× that section — proportions typical of a 51300 thrust section. At the printed limiting speed of 2,400 r/min the mean pitch diameter dm ≈ 110.0 mm implies a dn value around 264k mm·r/min; the 1,700 r/min reference speed is the thermal-planning value under catalogue load. Stack/annulus proportions: the 44 mm axial stack over the 10,367 mm² washer annulus gives 4.24 mm of height per annular square millimetre ×10⁻³, and at 2700 g the bearing holds about 144.4 kN of C0 per kilogram. Minimum-load arithmetic: with dm ≈ 110.0 mm and factor A 0.79, Fam ≈ A·(n·dm/1000)² at the 1,700 r/min reference speed is about 27.6 kN for 51316; below that preload the balls skid and smear the tracks. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 80 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 159/390 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "winch drums and reducer housings",
      "heavy crane hooks and hoist blocks",
      "vertical motor and pump thrust bearings"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.79; for 51316 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 159 kN track before first rotation.",
      "When the housing seat cannot be machined square to the 80 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51300 bearing.",
      "The 51316 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 80 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Ordering discipline for 51316: the catalogue page quotes 51316 and its 159/390 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51316-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 80 mm, OD 140 mm, height 44 mm; weight 2700 g. Load figures from SKF 17000: dynamic 159 kN, static 390 kN, fatigue limit 13.7 kN; reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51316 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 16 decodes to 80 mm (code 16 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51316-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.79 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51316",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51316-SKF",
      "51316"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51416-M",
    "brand": "SKF",
    "manufacturer_designation": "51416 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 68,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 302,
    "static_load_kN": 750,
    "fatigue_load_limit_kN": 25,
    "reference_speed_rpm": 1200,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "weight_g": 7950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51416 M is SKF's 80 mm-bore single-direction thrust ball bearing in the 51400 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 80×170×68 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 16 encode the bore as 80 mm (code 16 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 80×170×68 mm (3.15×6.693×2.677 in), 45.0 mm radial section, C 302 kN, C0 750 kN, Pu 25 kN. reference speed 1,200 r/min (thermal) and limiting speed 1,700 r/min (mechanical), catalogue mass 7950 g. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 2.3 at the 1,700 r/min limiting speed raises the required axial preload to about 103.9 kN; the reference-speed value 51.7 kN is the thermal design point. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51416 M covers about 17,671 mm², distributing C0 750 kN over a mean track circle of π·dm ≈ 393 mm. Minimum-load arithmetic: with dm ≈ 125.0 mm and factor A 2.3, Fam ≈ A·(n·dm/1000)² at the 1,200 r/min reference speed is about 51.7 kN for 51416 M; below that preload the balls skid and smear the tracks. Sizing arithmetic on the 80 mm bore: 302 kN C over the 45.0 mm radial section gives 6.7 kN per section millimetre, and the 68 mm stack height is 1.51× that section — proportions typical of a 51400 thrust section. Imperial cross-check for procurement drawings: 3.15 in bore, 6.693 in OD, 2.677 in height, and the 7950 g catalogue mass converts to 7.950 kg (280.4 oz). Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 7950 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 80 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "vertical motor and pump thrust bearings",
      "heavy crane hooks and hoist blocks",
      "large screw jacks and press rams"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The 51416 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 80 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51416 against two-way load lifts the loose washer off its raceway.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 302 kN track before first rotation.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51416 M as the single flat brass execution; other order numbers of the 51416 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51416-M?",
        "a": "51416 M measures 80 mm bore × 170 mm OD × 68 mm bearing height (3.15 × 6.693 × 2.677 in), mass about 7950 g. SKF 17000 ratings: C 302 kN, C0 750 kN, Pu 25 kN, reference speed 1,200 r/min (thermal) and limiting speed 1,700 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51416 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 16 encode the bore as 80 mm (code 16 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, M-cage product) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "Can 51416-M carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 80 mm shaft must go to a separate radial bearing; mixed loading through 51416 M edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51416",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×170×68 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51416-M",
      "51416 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51117-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51117",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 85,
    "D_mm": 110,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 44.9,
    "static_load_kN": 146,
    "fatigue_load_limit_kN": 5.4,
    "reference_speed_rpm": 3000,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 440,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51117 is a SKF single-direction thrust ball bearing for a 85 mm seat, built to ISO 104, with a flat housing seating surface, 85×110×19 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 17 decodes to 85 mm (code 17 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 85×110×19 mm (3.346×4.331×0.748 in), 12.5 mm radial section, C 44.9 kN, C0 146 kN, Pu 5.4 kN. reference speed 3,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 440 g. Load balance: C0 146 kN against C 44.9 kN gives a 3.25 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 5.4 kN enters the adjusted-life check. Envelope economics: the 19 mm axial height over a 12.5 mm radial section yields 2.4 kN of dynamic capacity per height millimetre, and the bearing weighs 440 g for 44.9 kN C — about 10 g per rated kN. Sizing arithmetic on the 85 mm bore: 44.9 kN C over the 12.5 mm radial section gives 3.6 kN per section millimetre, and the 19 mm stack height is 1.52× that section — proportions typical of a 51100 thrust section. Speed band width for this size is 1,300 r/min between reference and limiting (1.43× ratio); lubrication, preload and heat removal decide where inside that band 51117 can actually run. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51117 covers about 3,829 mm², distributing C0 146 kN over a mean track circle of π·dm ≈ 306 mm. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 19 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 44.9 kN C.",
    "applications": [
      "vertical motor and pump thrust bearings",
      "heavy crane hooks and hoist blocks",
      "large screw jacks and press rams"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51117 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 85 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 19 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The 44.9/146 kN figures belong to 51117 specifically (the single flat pressed steel execution of 51117); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51117-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 85 mm, OD 110 mm, height 19 mm; weight 440 g. Load figures from SKF 17000: dynamic 44.9 kN, static 146 kN, fatigue limit 5.4 kN; reference speed 3,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51117 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 17 decodes to 85 mm (code 17 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51117-SKF?",
        "a": "The 3,000 r/min reference speed is the thermal balance under catalogue load; the 4,300 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51117-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.14 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51117",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51117-SKF",
      "51117"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51217-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51217",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 85,
    "D_mm": 125,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 97.5,
    "static_load_kN": 275,
    "fatigue_load_limit_kN": 9.8,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51217 is an ISO 104 single-direction thrust ball bearing, 85 mm bore and 125 mm OD on a flat housing seat, standing 31 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 17: bore 85 mm (code 17 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 85×125×31 mm (3.346×4.921×1.22 in), 20.0 mm radial section, C 97.5 kN, C0 275 kN, Pu 9.8 kN. reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 1200 g. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51217 covers about 6,597 mm², distributing C0 275 kN over a mean track circle of π·dm ≈ 330 mm. Load balance: C0 275 kN against C 97.5 kN gives a 2.82 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 9.8 kN enters the adjusted-life check. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.39 at the 3,000 r/min limiting speed raises the required axial preload to about 38.7 kN; the reference-speed value 20.8 kN is the thermal design point. Capacity density: 97.5 kN C from 1.200 kg of bearing steel gives about 81.3 kN per kilogram; static density is correspondingly 229.2 kN/kg at C0 275 kN. Track-circle loading: per millimetre of mean track circumference the 97.5 kN dynamic rating corresponds to roughly 0.30 kN/mm of π·dm track, a useful comparison against the other dimension series of the 85 mm bore. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 31 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 97.5 kN C.",
    "applications": [
      "turret and slewing-bearing adjustment screws",
      "vertical motor and pump thrust bearings",
      "winch drums and reducer housings"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 85 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 85 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 31 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Ordering discipline for 51217: the catalogue page quotes 51217 and its 97.5/275 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51217-SKF?",
        "a": "The catalogue envelope is 85×125×31 mm, mass 1200 g; ratings C 97.5 kN / C0 275 kN / Pu 9.8 kN, reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51217 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 17: bore 85 mm (code 17 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51217-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 3,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 85 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51217",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51217-SKF",
      "51217"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51317-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51317",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 49,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 174,
    "static_load_kN": 405,
    "fatigue_load_limit_kN": 14,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 3550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51317 is SKF's 85 mm-bore single-direction thrust ball bearing in the 51300 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 85×150×49 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 17 encode the bore as 85 mm (code 17 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 85×150×49 mm (3.346×5.906×1.929 in), 32.5 mm radial section, C 174 kN, C0 405 kN, Pu 14 kN. reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 3550 g. Rating split for documentation: dynamic 174 kN (L10 life), static 405 kN (safety factor s0), fatigue limit 14 kN (adjusted life) — three different uses of three different numbers for 51317, none interchangeable with another. Imperial cross-check for procurement drawings: 3.346 in bore, 5.906 in OD, 1.929 in height, and the 3550 g catalogue mass converts to 3.550 kg (125.2 oz). Speed band width for this size is 600 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 51317 can actually run. Section proportions: the 32.5 mm radial section compares with 85 mm of bore (section/bore ≈ 0.38) and the 49 mm height is 1.51× that section — the proportions that identify the 51300 envelope at a glance. Envelope economics: the 49 mm axial height over a 32.5 mm radial section yields 3.6 kN of dynamic capacity per height millimetre, and the bearing weighs 3550 g for 174 kN C — about 20 g per rated kN. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 49 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 174 kN C.",
    "applications": [
      "heavy crane hooks and hoist blocks",
      "vertical motor and pump thrust bearings",
      "winch drums and reducer housings"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 49 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 85 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The 51317 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 85 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51317 as the single flat pressed steel execution; other order numbers of the 51317 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51317-SKF?",
        "a": "51317 measures 85 mm bore × 150 mm OD × 49 mm bearing height (3.346 × 5.906 × 1.929 in), mass about 3550 g. SKF 17000 ratings: C 174 kN, C0 405 kN, Pu 14 kN, reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51317 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 17 encode the bore as 85 mm (code 17 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "Can 51317-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 85 mm shaft must go to a separate radial bearing; mixed loading through 51317 edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51317",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 85×150×49 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51317-SKF",
      "51317"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51417-M",
    "brand": "SKF",
    "manufacturer_designation": "51417 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 72,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 286,
    "static_load_kN": 750,
    "fatigue_load_limit_kN": 24,
    "reference_speed_rpm": 1200,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "weight_g": 9450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51400 series order number 51417 M is a SKF single-direction thrust ball bearing for a 85 mm seat, built to ISO 104, with a flat housing seating surface, 85×180×72 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 17 decodes to 85 mm (code 17 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 85×180×72 mm (3.346×7.087×2.835 in), 47.5 mm radial section, C 286 kN, C0 750 kN, Pu 24 kN. reference speed 1,200 r/min (thermal) and limiting speed 1,600 r/min (mechanical), catalogue mass 9450 g. Speed planning separates the two ceilings mechanically: the pressed brass cage and balls tolerate 1,600 r/min while thermal balance under catalogue load sets the 1,200 r/min reference; at dm ≈ 132.5 mm the corresponding dn is approximately 212k mm·r/min. Light-load floor: Pu = 24 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51417 M; the number is 8 % of the 286 kN dynamic rating. Capacity density: 286 kN C from 9.450 kg of bearing steel gives about 30.3 kN per kilogram; static density is correspondingly 79.4 kN/kg at C0 750 kN. Minimum-load arithmetic: with dm ≈ 132.5 mm and factor A 2.9, Fam ≈ A·(n·dm/1000)² at the 1,200 r/min reference speed is about 73.3 kN for 51417 M; below that preload the balls skid and smear the tracks. Sizing arithmetic on the 85 mm bore: 286 kN C over the 47.5 mm radial section gives 6.0 kN per section millimetre, and the 72 mm stack height is 1.52× that section — proportions typical of a 51400 thrust section. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 9450 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 85 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "heavy crane hooks and hoist blocks",
      "large screw jacks and press rams",
      "turret and slewing-bearing adjustment screws"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "track rust staining from condensate during long idle periods in humid plant air",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 286/750 kN and the available 180 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 51417 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 85 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "When the housing seat cannot be machined square to the 85 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51400 bearing.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Ordering discipline for 51417: the catalogue page quotes 51417 M and its 286/750 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51417-M?",
        "a": "Boundary dimensions to ISO 104: bore 85 mm, OD 180 mm, height 72 mm; weight 9450 g. Load figures from SKF 17000: dynamic 286 kN, static 750 kN, fatigue limit 24 kN; reference speed 1,200 r/min (thermal) and limiting speed 1,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51417 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 17 decodes to 85 mm (code 17 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51417-M lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 1,600 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 85 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51417",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51417-M",
      "51417 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51118-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51118",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 90,
    "D_mm": 120,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 59.2,
    "static_load_kN": 208,
    "fatigue_load_limit_kN": 7.5,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 670,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51118 is an ISO 104 single-direction thrust ball bearing, 90 mm bore and 120 mm OD on a flat housing seat, standing 22 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 18: bore 90 mm (code 18 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 90×120×22 mm (3.543×4.724×0.866 in), 15.0 mm radial section, C 59.2 kN, C0 208 kN, Pu 7.5 kN. reference speed 2,600 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 670 g. Mass and section check: 670 g inside the 90×120×22 mm outline leaves a 15.0 mm radial section, and the 208 kN static rating is 3.51× the dynamic rating — plan static safety and minimum preload against those figures. Light-load floor: Pu = 7.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51118; the number is 13 % of the 59.2 kN dynamic rating. Imperial cross-check for procurement drawings: 3.543 in bore, 4.724 in OD, 0.866 in height, and the 670 g catalogue mass converts to 0.670 kg (23.6 oz). Load balance: C0 208 kN against C 59.2 kN gives a 3.51 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 7.5 kN enters the adjusted-life check. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.22 at the 3,800 r/min limiting speed raises the required axial preload to about 35.0 kN; the reference-speed value 16.4 kN is the thermal design point. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 90 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 59.2/208 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "large screw jacks and press rams",
      "vertical motor and pump thrust bearings",
      "turret and slewing-bearing adjustment screws"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 90 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 22 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51118 against two-way load lifts the loose washer off its raceway.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Ordering discipline for 51118: the catalogue page quotes 51118 and its 59.2/208 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51118-SKF?",
        "a": "The catalogue envelope is 90×120×22 mm, mass 670 g; ratings C 59.2 kN / C0 208 kN / Pu 7.5 kN, reference speed 2,600 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51118 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 18: bore 90 mm (code 18 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51118-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.22 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51118",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51118-SKF",
      "51118"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51218-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51218",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 90,
    "D_mm": 135,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 112,
    "static_load_kN": 290,
    "fatigue_load_limit_kN": 10.4,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 1700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51218 is SKF's 90 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 90×135×35 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 18 encode the bore as 90 mm (code 18 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 90×135×35 mm (3.543×5.315×1.378 in), 22.5 mm radial section, C 112 kN, C0 290 kN, Pu 10.4 kN. reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical), catalogue mass 1700 g. Sizing arithmetic on the 90 mm bore: 112 kN C over the 22.5 mm radial section gives 5.0 kN per section millimetre, and the 35 mm stack height is 1.56× that section — proportions typical of a 51200 thrust section. Envelope economics: the 35 mm axial height over a 22.5 mm radial section yields 3.2 kN of dynamic capacity per height millimetre, and the bearing weighs 1700 g for 112 kN C — about 15 g per rated kN. Pitch-diameter arithmetic: dm = (90+135)/2 = 112.5 mm; at the 2,800 r/min limiting speed that corresponds to roughly 315k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Mass and section check: 1700 g inside the 90×135×35 mm outline leaves a 22.5 mm radial section, and the 290 kN static rating is 2.59× the dynamic rating — plan static safety and minimum preload against those figures. Section proportions: the 22.5 mm radial section compares with 90 mm of bore (section/bore ≈ 0.25) and the 35 mm height is 1.56× that section — the proportions that identify the 51200 envelope at a glance. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 35 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 112 kN C.",
    "applications": [
      "winch drums and reducer housings",
      "large screw jacks and press rams",
      "heavy crane hooks and hoist blocks"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "false brinelling of the stationary tracks while the machine stands under vibration"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 35 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 90 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 112 kN track before first rotation.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51218 as the single flat pressed steel execution; other order numbers of the 51218 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51218-SKF?",
        "a": "51218 measures 90 mm bore × 135 mm OD × 35 mm bearing height (3.543 × 5.315 × 1.378 in), mass about 1700 g. SKF 17000 ratings: C 112 kN, C0 290 kN, Pu 10.4 kN, reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51218 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 18 encode the bore as 90 mm (code 18 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51218-SKF lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 2,800 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51218",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×135×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51218-SKF",
      "51218"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51318-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51318",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 90,
    "D_mm": 155,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 182,
    "static_load_kN": 440,
    "fatigue_load_limit_kN": 14.6,
    "reference_speed_rpm": 1500,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 3800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51300 series order number 51318 is a SKF single-direction thrust ball bearing for a 90 mm seat, built to ISO 104, with a flat housing seating surface, 90×155×50 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 18 decodes to 90 mm (code 18 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 90×155×50 mm (3.543×6.102×1.969 in), 32.5 mm radial section, C 182 kN, C0 440 kN, Pu 14.6 kN. reference speed 1,500 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 3800 g. Pitch-diameter arithmetic: dm = (90+155)/2 = 122.5 mm; at the 2,200 r/min limiting speed that corresponds to roughly 270k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Rating split for documentation: dynamic 182 kN (L10 life), static 440 kN (safety factor s0), fatigue limit 14.6 kN (adjusted life) — three different uses of three different numbers for 51318, none interchangeable with another. Section proportions: the 32.5 mm radial section compares with 90 mm of bore (section/bore ≈ 0.36) and the 50 mm height is 1.54× that section — the proportions that identify the 51300 envelope at a glance. Minimum-load arithmetic: with dm ≈ 122.5 mm and factor A 1.3, Fam ≈ A·(n·dm/1000)² at the 1,500 r/min reference speed is about 43.9 kN for 51318; below that preload the balls skid and smear the tracks. Light-load floor: Pu = 14.6 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51318; the number is 8 % of the 182 kN dynamic rating. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 90 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 182/440 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "vertical motor and pump thrust bearings",
      "winch drums and reducer housings",
      "heavy crane hooks and hoist blocks"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "When the housing seat cannot be machined square to the 90 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51300 bearing.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 1.3; for 51318 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 51318 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 90 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The 182/440 kN figures belong to 51318 specifically (the single flat pressed steel execution of 51318); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51318-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 90 mm, OD 155 mm, height 50 mm; weight 3800 g. Load figures from SKF 17000: dynamic 182 kN, static 440 kN, fatigue limit 14.6 kN; reference speed 1,500 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51318 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 18 decodes to 90 mm (code 18 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51318 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51318-SKF?",
        "a": "The 1,500 r/min reference speed is the thermal balance under catalogue load; the 2,200 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51318",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×155×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51318-SKF",
      "51318"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51418-M",
    "brand": "SKF",
    "manufacturer_designation": "51418 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 77,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 307,
    "static_load_kN": 815,
    "fatigue_load_limit_kN": 25.5,
    "reference_speed_rpm": 1100,
    "limiting_speed_rpm": 1500,
    "max_rpm": 1500,
    "weight_g": 11000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51400 series order number 51418 M is a SKF single-direction thrust ball bearing for a 90 mm seat, built to ISO 104, with a flat housing seating surface, 90×190×77 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 18 decodes to 90 mm (code 18 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 90×190×77 mm (3.543×7.48×3.031 in), 50.0 mm radial section, C 307 kN, C0 815 kN, Pu 25.5 kN. reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical), catalogue mass 11000 g. Bore-to-OD planning: OD 190 over bore 90 is a 2.11× step for this size, and the 77 mm height gives a bore/height ratio of 1.17; use these ratios when the housing recess around the 90 mm shaft is the first constraint. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51418 M covers about 21,991 mm², distributing C0 815 kN over a mean track circle of π·dm ≈ 440 mm. Speed band width for this size is 400 r/min between reference and limiting (1.36× ratio); lubrication, preload and heat removal decide where inside that band 51418 M can actually run. Sizing arithmetic on the 90 mm bore: 307 kN C over the 50.0 mm radial section gives 6.1 kN per section millimetre, and the 77 mm stack height is 1.54× that section — proportions typical of a 51400 thrust section. Imperial cross-check for procurement drawings: 3.543 in bore, 7.48 in OD, 3.031 in height, and the 11000 g catalogue mass converts to 11.000 kg (388.0 oz). Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51418 M adds a small amount of mass and cage strength without changing the 90×190×77 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,500 r/min ceiling.",
    "applications": [
      "vertical motor and pump thrust bearings",
      "winch drums and reducer housings",
      "turret and slewing-bearing adjustment screws"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "false brinelling of the stationary tracks while the machine stands under vibration"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 90 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51400 bearing.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51418 against two-way load lifts the loose washer off its raceway.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 307/815 kN and the available 190 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 90 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Ordering discipline for 51418: the catalogue page quotes 51418 M and its 307/815 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51418-M?",
        "a": "Boundary dimensions to ISO 104: bore 90 mm, OD 190 mm, height 77 mm; weight 11000 g. Load figures from SKF 17000: dynamic 307 kN, static 815 kN, fatigue limit 25.5 kN; reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51418 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 18 decodes to 90 mm (code 18 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51418-M?",
        "a": "The 1,100 r/min reference speed is the thermal balance under catalogue load; the 1,500 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51418-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 3.5 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51418",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51418-M",
      "51418 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51120-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51120",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 100,
    "D_mm": 135,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 80.6,
    "static_load_kN": 265,
    "fatigue_load_limit_kN": 9.15,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 970,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51120 is SKF's 100 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 100×135×25 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 20 encode the bore as 100 mm (code 20 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 100×135×25 mm (3.937×5.315×0.984 in), 17.5 mm radial section, C 80.6 kN, C0 265 kN, Pu 9.15 kN. reference speed 2,400 r/min (thermal) and limiting speed 3,200 r/min (mechanical), catalogue mass 970 g. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.44 at the 3,200 r/min limiting speed raises the required axial preload to about 62.2 kN; the reference-speed value 35.0 kN is the thermal design point. Bore-to-OD planning: OD 135 over bore 100 is a 1.35× step for this size, and the 25 mm height gives a bore/height ratio of 4.00; use these ratios when the housing recess around the 100 mm shaft is the first constraint. Rating split for documentation: dynamic 80.6 kN (L10 life), static 265 kN (safety factor s0), fatigue limit 9.15 kN (adjusted life) — three different uses of three different numbers for 51120, none interchangeable with another. Capacity density: 80.6 kN C from 0.970 kg of bearing steel gives about 83.1 kN per kilogram; static density is correspondingly 273.2 kN/kg at C0 265 kN. Track-circle loading: per millimetre of mean track circumference the 80.6 kN dynamic rating corresponds to roughly 0.22 kN/mm of π·dm track, a useful comparison against the other dimension series of the 100 mm bore. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 25 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 80.6 kN C.",
    "applications": [
      "winch drums and reducer housings",
      "heavy crane hooks and hoist blocks",
      "turret and slewing-bearing adjustment screws"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "track rust staining from condensate during long idle periods in humid plant air"
    ],
    "pitfalls": [
      "The 51120 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 100 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51120 against two-way load lifts the loose washer off its raceway.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 100 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.44; for 51120 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51120 as the single flat pressed steel execution; other order numbers of the 51120 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51120-SKF?",
        "a": "51120 measures 100 mm bore × 135 mm OD × 25 mm bearing height (3.937 × 5.315 × 0.984 in), mass about 970 g. SKF 17000 ratings: C 80.6 kN, C0 265 kN, Pu 9.15 kN, reference speed 2,400 r/min (thermal) and limiting speed 3,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51120 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 20 encode the bore as 100 mm (code 20 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 100 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51120 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51120",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51120-SKF",
      "51120"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51220-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51220",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 100,
    "D_mm": 150,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 119,
    "static_load_kN": 325,
    "fatigue_load_limit_kN": 10.8,
    "reference_speed_rpm": 1800,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 2200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51220 is an ISO 104 single-direction thrust ball bearing, 100 mm bore and 150 mm OD on a flat housing seat, standing 38 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 20: bore 100 mm (code 20 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 100×150×38 mm (3.937×5.906×1.496 in), 25.0 mm radial section, C 119 kN, C0 325 kN, Pu 10.8 kN. reference speed 1,800 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 2200 g. Bore-to-OD planning: OD 150 over bore 100 is a 1.50× step for this size, and the 38 mm height gives a bore/height ratio of 2.63; use these ratios when the housing recess around the 100 mm shaft is the first constraint. Sizing arithmetic on the 100 mm bore: 119 kN C over the 25.0 mm radial section gives 4.8 kN per section millimetre, and the 38 mm stack height is 1.52× that section — proportions typical of a 51200 thrust section. Load balance: C0 325 kN against C 119 kN gives a 2.73 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 10.8 kN enters the adjusted-life check. Stack/annulus proportions: the 38 mm axial stack over the 9,817 mm² washer annulus gives 3.87 mm of height per annular square millimetre ×10⁻³, and at 2200 g the bearing holds about 147.7 kN of C0 per kilogram. Mass and section check: 2200 g inside the 100×150×38 mm outline leaves a 25.0 mm radial section, and the 325 kN static rating is 2.73× the dynamic rating — plan static safety and minimum preload against those figures. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 38 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 119 kN C.",
    "applications": [
      "turret and slewing-bearing adjustment screws",
      "winch drums and reducer housings",
      "vertical motor and pump thrust bearings"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51220 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 100 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 38 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 100 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51220 as the single flat pressed steel execution; other order numbers of the 51220 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51220-SKF?",
        "a": "The catalogue envelope is 100×150×38 mm, mass 2200 g; ratings C 119 kN / C0 325 kN / Pu 10.8 kN, reference speed 1,800 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51220 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 20: bore 100 mm (code 20 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51220-SKF carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 100 mm shaft must go to a separate radial bearing; mixed loading through 51220 edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51220",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 100×150×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51220-SKF",
      "51220"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51320-SKF",
    "brand": "SKF",
    "manufacturer_designation": "51320",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 100,
    "D_mm": 170,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 225,
    "static_load_kN": 570,
    "fatigue_load_limit_kN": 18.3,
    "reference_speed_rpm": 1400,
    "limiting_speed_rpm": 1900,
    "max_rpm": 1900,
    "weight_g": 4950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51300 series order number 51320 is a SKF single-direction thrust ball bearing for a 100 mm seat, built to ISO 104, with a flat housing seating surface, 100×170×55 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 20 decodes to 100 mm (code 20 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 100×170×55 mm (3.937×6.693×2.165 in), 35.0 mm radial section, C 225 kN, C0 570 kN, Pu 18.3 kN. reference speed 1,400 r/min (thermal) and limiting speed 1,900 r/min (mechanical), catalogue mass 4950 g. Imperial cross-check for procurement drawings: 3.937 in bore, 6.693 in OD, 2.165 in height, and the 4950 g catalogue mass converts to 4.950 kg (174.6 oz). Section proportions: the 35.0 mm radial section compares with 100 mm of bore (section/bore ≈ 0.35) and the 55 mm height is 1.57× that section — the proportions that identify the 51300 envelope at a glance. Rating split for documentation: dynamic 225 kN (L10 life), static 570 kN (safety factor s0), fatigue limit 18.3 kN (adjusted life) — three different uses of three different numbers for 51320, none interchangeable with another. Bore-to-OD planning: OD 170 over bore 100 is a 1.70× step for this size, and the 55 mm height gives a bore/height ratio of 1.82; use these ratios when the housing recess around the 100 mm shaft is the first constraint. Stack/annulus proportions: the 55 mm axial stack over the 14,844 mm² washer annulus gives 3.71 mm of height per annular square millimetre ×10⁻³, and at 4950 g the bearing holds about 115.2 kN of C0 per kilogram. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 100 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 225/570 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "turret and slewing-bearing adjustment screws",
      "vertical motor and pump thrust bearings",
      "heavy crane hooks and hoist blocks"
    ],
    "failure_modes": [
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 1.9; for 51320 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "When the housing seat cannot be machined square to the 100 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51300 bearing.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 225/570 kN and the available 170 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Ordering discipline for 51320: the catalogue page quotes 51320 and its 225/570 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51320-SKF?",
        "a": "Boundary dimensions to ISO 104: bore 100 mm, OD 170 mm, height 55 mm; weight 4950 g. Load figures from SKF 17000: dynamic 225 kN, static 570 kN, fatigue limit 18.3 kN; reference speed 1,400 r/min (thermal) and limiting speed 1,900 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51320 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 20 decodes to 100 mm (code 20 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51320-SKF?",
        "a": "The 1,400 r/min reference speed is the thermal balance under catalogue load; the 1,900 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51320-SKF need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 1.9 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51320",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51320-SKF",
      "51320"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51420-M",
    "brand": "SKF",
    "manufacturer_designation": "51420 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 100,
    "D_mm": 210,
    "B_mm": 85,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 371,
    "static_load_kN": 1060,
    "fatigue_load_limit_kN": 31.5,
    "reference_speed_rpm": 950,
    "limiting_speed_rpm": 1400,
    "max_rpm": 1400,
    "weight_g": 15000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51400 series order number 51420 M is a SKF single-direction thrust ball bearing for a 100 mm seat, built to ISO 104, with a flat housing seating surface, 100×210×85 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 20 decodes to 100 mm (code 20 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 100×210×85 mm (3.937×8.268×3.346 in), 55.0 mm radial section, C 371 kN, C0 1060 kN, Pu 31.5 kN. reference speed 950 r/min (thermal) and limiting speed 1,400 r/min (mechanical), catalogue mass 15000 g. Selection figures for 51420 M: the C0/C ratio is 2.86, Pu 31.5 kN is about 8 % of C, and the catalogue mass works out to roughly 150 g per millimetre of bore; the printed minimum-load factor is A 5.8. Capacity density: 371 kN C from 15.000 kg of bearing steel gives about 24.7 kN per kilogram; static density is correspondingly 70.7 kN/kg at C0 1060 kN. Minimum-load arithmetic: with dm ≈ 155.0 mm and factor A 5.8, Fam ≈ A·(n·dm/1000)² at the 950 r/min reference speed is about 125.8 kN for 51420 M; below that preload the balls skid and smear the tracks. Sizing arithmetic on the 100 mm bore: 371 kN C over the 55.0 mm radial section gives 6.7 kN per section millimetre, and the 85 mm stack height is 1.55× that section — proportions typical of a 51400 thrust section. Stack/annulus proportions: the 85 mm axial stack over the 26,782 mm² washer annulus gives 3.17 mm of height per annular square millimetre ×10⁻³, and at 15000 g the bearing holds about 70.7 kN of C0 per kilogram. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 15000 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 100 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "large screw jacks and press rams",
      "vertical motor and pump thrust bearings",
      "turret and slewing-bearing adjustment screws"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 100 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51400 bearing.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 85 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 5.8; for 51420 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Ordering discipline for 51420: the catalogue page quotes 51420 M and its 371/1060 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51420-M?",
        "a": "Boundary dimensions to ISO 104: bore 100 mm, OD 210 mm, height 85 mm; weight 15000 g. Load figures from SKF 17000: dynamic 371 kN, static 1060 kN, fatigue limit 31.5 kN; reference speed 950 r/min (thermal) and limiting speed 1,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51420 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 20 decodes to 100 mm (code 20 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51420 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51420-M?",
        "a": "The 950 r/min reference speed is the thermal balance under catalogue load; the 1,400 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51420",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51420-M",
      "51420 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51122",
    "brand": "SKF",
    "manufacturer_designation": "51122",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 110,
    "D_mm": 145,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 83.2,
    "static_load_kN": 285,
    "fatigue_load_limit_kN": 9.5,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 1050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51122 is a SKF single-direction thrust ball bearing for a 110 mm seat, built to ISO 104, with a flat housing seating surface, 110×145×25 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 22 decodes to 110 mm (code 22 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 110×145×25 mm (4.331×5.709×0.984 in), 17.5 mm radial section, C 83.2 kN, C0 285 kN, Pu 9.5 kN. reference speed 2,200 r/min (thermal) and limiting speed 3,200 r/min (mechanical), catalogue mass 1050 g. Selection figures for 51122: the C0/C ratio is 3.43, Pu 9.5 kN is about 11 % of C, and the catalogue mass works out to roughly 10 g per millimetre of bore; the printed minimum-load factor is A 0.52. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.52 at the 3,200 r/min limiting speed raises the required axial preload to about 86.6 kN; the reference-speed value 40.9 kN is the thermal design point. Stack/annulus proportions: the 25 mm axial stack over the 7,010 mm² washer annulus gives 3.57 mm of height per annular square millimetre ×10⁻³, and at 1050 g the bearing holds about 271.4 kN of C0 per kilogram. Sizing arithmetic on the 110 mm bore: 83.2 kN C over the 17.5 mm radial section gives 4.8 kN per section millimetre, and the 25 mm stack height is 1.43× that section — proportions typical of a 51100 thrust section. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 3,200 r/min while thermal balance under catalogue load sets the 2,200 r/min reference; at dm ≈ 127.5 mm the corresponding dn is approximately 408k mm·r/min. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 25 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 83.2 kN C.",
    "applications": [
      "turret and slewing-bearing adjustment screws",
      "vertical motor and pump thrust bearings",
      "winch drums and reducer housings"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51122 against two-way load lifts the loose washer off its raceway.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 83.2 kN track before first rotation.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 83.2/285 kN and the available 145 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 51122 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 110 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51122 as the single flat pressed steel execution; other order numbers of the 51122 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51122?",
        "a": "Boundary dimensions to ISO 104: bore 110 mm, OD 145 mm, height 25 mm; weight 1050 g. Load figures from SKF 17000: dynamic 83.2 kN, static 285 kN, fatigue limit 9.5 kN; reference speed 2,200 r/min (thermal) and limiting speed 3,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51122 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 22 decodes to 110 mm (code 22 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51122 lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 3,200 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 110 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51122-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "51122",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51122"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51222",
    "brand": "SKF",
    "manufacturer_designation": "51222",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 110,
    "D_mm": 160,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 125,
    "static_load_kN": 365,
    "fatigue_load_limit_kN": 11.6,
    "reference_speed_rpm": 1700,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 2400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51222 is SKF's 110 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 110×160×38 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 22 encode the bore as 110 mm (code 22 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 110×160×38 mm (4.331×6.299×1.496 in), 25.0 mm radial section, C 125 kN, C0 365 kN, Pu 11.6 kN. reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 2400 g. Rating split for documentation: dynamic 125 kN (L10 life), static 365 kN (safety factor s0), fatigue limit 11.6 kN (adjusted life) — three different uses of three different numbers for 51222, none interchangeable with another. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 2,400 r/min while thermal balance under catalogue load sets the 1,700 r/min reference; at dm ≈ 135.0 mm the corresponding dn is approximately 324k mm·r/min. Capacity density: 125 kN C from 2.400 kg of bearing steel gives about 52.1 kN per kilogram; static density is correspondingly 152.1 kN/kg at C0 365 kN. Sizing arithmetic on the 110 mm bore: 125 kN C over the 25.0 mm radial section gives 5.0 kN per section millimetre, and the 38 mm stack height is 1.52× that section — proportions typical of a 51200 thrust section. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51222 covers about 10,603 mm², distributing C0 365 kN over a mean track circle of π·dm ≈ 424 mm. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 38 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 125 kN C.",
    "applications": [
      "turret and slewing-bearing adjustment screws",
      "vertical motor and pump thrust bearings",
      "winch drums and reducer housings"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 110 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.79; for 51222 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 125 kN track before first rotation.",
      "The 51222 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 110 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Ordering discipline for 51222: the catalogue page quotes 51222 and its 125/365 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51222?",
        "a": "51222 measures 110 mm bore × 160 mm OD × 38 mm bearing height (4.331 × 6.299 × 1.496 in), mass about 2400 g. SKF 17000 ratings: C 125 kN, C0 365 kN, Pu 11.6 kN, reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51222 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 22 encode the bore as 110 mm (code 22 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51222?",
        "a": "The 1,700 r/min reference speed is the thermal balance under catalogue load; the 2,400 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51222 need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.79 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51222-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×160×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51222",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51222"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51322-M",
    "brand": "SKF",
    "manufacturer_designation": "51322 M",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 110,
    "D_mm": 190,
    "B_mm": 63,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 281,
    "static_load_kN": 815,
    "fatigue_load_limit_kN": 24.5,
    "reference_speed_rpm": 1200,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "weight_g": 7850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51322 M is SKF's 110 mm-bore single-direction thrust ball bearing in the 51300 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 110×190×63 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 22 encode the bore as 110 mm (code 22 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 110×190×63 mm (4.331×7.48×2.48 in), 40.0 mm radial section, C 281 kN, C0 815 kN, Pu 24.5 kN. reference speed 1,200 r/min (thermal) and limiting speed 1,700 r/min (mechanical), catalogue mass 7850 g. Pitch-diameter arithmetic: dm = (110+190)/2 = 150.0 mm; at the 1,700 r/min limiting speed that corresponds to roughly 255k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51322 M covers about 18,850 mm², distributing C0 815 kN over a mean track circle of π·dm ≈ 471 mm. Sizing arithmetic on the 110 mm bore: 281 kN C over the 40.0 mm radial section gives 7.0 kN per section millimetre, and the 63 mm stack height is 1.57× that section — proportions typical of a 51300 thrust section. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 3.2 at the 1,700 r/min limiting speed raises the required axial preload to about 208.1 kN; the reference-speed value 103.7 kN is the thermal design point. Section proportions: the 40.0 mm radial section compares with 110 mm of bore (section/bore ≈ 0.36) and the 63 mm height is 1.57× that section — the proportions that identify the 51300 envelope at a glance. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 7850 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 110 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "heavy crane hooks and hoist blocks",
      "winch drums and reducer housings",
      "large screw jacks and press rams"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "false brinelling of the stationary tracks while the machine stands under vibration"
    ],
    "pitfalls": [
      "The 51322 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 110 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "When the housing seat cannot be machined square to the 110 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51300 bearing.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 110 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 281 kN track before first rotation.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51322 M as the single flat brass execution; other order numbers of the 51322 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51322-M?",
        "a": "51322 M measures 110 mm bore × 190 mm OD × 63 mm bearing height (4.331 × 7.48 × 2.48 in), mass about 7850 g. SKF 17000 ratings: C 281 kN, C0 815 kN, Pu 24.5 kN, reference speed 1,200 r/min (thermal) and limiting speed 1,700 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51322 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 22 encode the bore as 110 mm (code 22 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51322-M lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 1,700 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51322",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×190×63 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51322",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51322-M",
      "51322 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51422-M",
    "brand": "SKF",
    "manufacturer_designation": "51422 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 110,
    "D_mm": 230,
    "B_mm": 95,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 410,
    "static_load_kN": 1220,
    "fatigue_load_limit_kN": 34.5,
    "reference_speed_rpm": 900,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "weight_g": 20000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51400 series order number 51422 M is a SKF single-direction thrust ball bearing for a 110 mm seat, built to ISO 104, with a flat housing seating surface, 110×230×95 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 22 decodes to 110 mm (code 22 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 110×230×95 mm (4.331×9.055×3.74 in), 60.0 mm radial section, C 410 kN, C0 1220 kN, Pu 34.5 kN. reference speed 900 r/min (thermal) and limiting speed 1,300 r/min (mechanical), catalogue mass 20000 g. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 7.7 at the 1,300 r/min limiting speed raises the required axial preload to about 376.1 kN; the reference-speed value 180.2 kN is the thermal design point. Rating split for documentation: dynamic 410 kN (L10 life), static 1220 kN (safety factor s0), fatigue limit 34.5 kN (adjusted life) — three different uses of three different numbers for 51422 M, none interchangeable with another. Selection figures for 51422 M: the C0/C ratio is 2.98, Pu 34.5 kN is about 8 % of C, and the catalogue mass works out to roughly 182 g per millimetre of bore; the printed minimum-load factor is A 7.7. Light-load floor: Pu = 34.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51422 M; the number is 8 % of the 410 kN dynamic rating. Static-first selection data: 1220 kN C0 spread across the 95 mm stack gives 12.8 kN of static rating per height millimetre, and the 20000 g mass/C0 ratio is about 16 g per static kN — crane-hook and screw positions are normally sized on these two figures. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51422 M adds a small amount of mass and cage strength without changing the 110×230×95 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,300 r/min ceiling.",
    "applications": [
      "winch drums and reducer housings",
      "heavy crane hooks and hoist blocks",
      "vertical motor and pump thrust bearings"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 7.7; for 51422 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51422 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 110 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51400 bearing.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Ordering discipline for 51422: the catalogue page quotes 51422 M and its 410/1220 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51422-M?",
        "a": "Boundary dimensions to ISO 104: bore 110 mm, OD 230 mm, height 95 mm; weight 20000 g. Load figures from SKF 17000: dynamic 410 kN, static 1220 kN, fatigue limit 34.5 kN; reference speed 900 r/min (thermal) and limiting speed 1,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51422 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 22 decodes to 110 mm (code 22 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51422-M lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 1,300 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 110 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51422",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51422-M",
      "51422 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51124",
    "brand": "SKF",
    "manufacturer_designation": "51124",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 120,
    "D_mm": 155,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 85.2,
    "static_load_kN": 305,
    "fatigue_load_limit_kN": 9.65,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 1150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51124 is a SKF single-direction thrust ball bearing for a 120 mm seat, built to ISO 104, with a flat housing seating surface, 120×155×25 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 24 decodes to 120 mm (code 24 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 120×155×25 mm (4.724×6.102×0.984 in), 17.5 mm radial section, C 85.2 kN, C0 305 kN, Pu 9.65 kN. reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 1150 g. Track-circle loading: per millimetre of mean track circumference the 85.2 kN dynamic rating corresponds to roughly 0.20 kN/mm of π·dm track, a useful comparison against the other dimension series of the 120 mm bore. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.58 at the 3,000 r/min limiting speed raises the required axial preload to about 98.7 kN; the reference-speed value 53.1 kN is the thermal design point. Speed band width for this size is 800 r/min between reference and limiting (1.36× ratio); lubrication, preload and heat removal decide where inside that band 51124 can actually run. Load balance: C0 305 kN against C 85.2 kN gives a 3.58 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 9.65 kN enters the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 2,200 r/min against a 3,000 r/min limiting speed, a reference-to-limit ratio of 0.73. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 25 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 85.2 kN C.",
    "applications": [
      "very heavy crane and ladle hooks",
      "large press rams and screwdown mechanisms",
      "offshore and dock winch drums"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 0.58; for 51124 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 120 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "When the housing seat cannot be machined square to the 120 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "The 51124 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 120 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Ordering discipline for 51124: the catalogue page quotes 51124 and its 85.2/305 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51124?",
        "a": "Boundary dimensions to ISO 104: bore 120 mm, OD 155 mm, height 25 mm; weight 1150 g. Load figures from SKF 17000: dynamic 85.2 kN, static 305 kN, fatigue limit 9.65 kN; reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51124 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 24 decodes to 120 mm (code 24 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51124 carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 120 mm shaft must go to a separate radial bearing; mixed loading through 51124 edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51124-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "51124",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51124"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51224",
    "brand": "SKF",
    "manufacturer_designation": "51224",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 120,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 127,
    "static_load_kN": 390,
    "fatigue_load_limit_kN": 11.8,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51224 is a SKF single-direction thrust ball bearing for a 120 mm seat, built to ISO 104, with a flat housing seating surface, 120×170×39 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 24 decodes to 120 mm (code 24 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 120×170×39 mm (4.724×6.693×1.535 in), 25.0 mm radial section, C 127 kN, C0 390 kN, Pu 11.8 kN. reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 2650 g. Rating split for documentation: dynamic 127 kN (L10 life), static 390 kN (safety factor s0), fatigue limit 11.8 kN (adjusted life) — three different uses of three different numbers for 51224, none interchangeable with another. Speed-ratio note for this exact unit: the reference speed is 1,600 r/min against a 2,200 r/min limiting speed, a reference-to-limit ratio of 0.73. Capacity density: 127 kN C from 2.650 kg of bearing steel gives about 47.9 kN per kilogram; static density is correspondingly 147.2 kN/kg at C0 390 kN. Minimum-load arithmetic: with dm ≈ 145.0 mm and factor A 1, Fam ≈ A·(n·dm/1000)² at the 1,600 r/min reference speed is about 53.8 kN for 51224; below that preload the balls skid and smear the tracks. Track-circle loading: per millimetre of mean track circumference the 127 kN dynamic rating corresponds to roughly 0.28 kN/mm of π·dm track, a useful comparison against the other dimension series of the 120 mm bore. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. Inspection after removal of a 39 mm-high stack means checking both washer faces: the loose housing washer often shows the first false-brinell marks under machine vibration even though the tight shaft washer carries the rotating load of 127 kN C.",
    "applications": [
      "marine gearbox thrust positions",
      "large press rams and screwdown mechanisms",
      "very heavy crane and ladle hooks"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 39 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 1; for 51224 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "When the housing seat cannot be machined square to the 120 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 127 kN track before first rotation.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51224 as the single flat pressed steel execution; other order numbers of the 51224 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51224?",
        "a": "Boundary dimensions to ISO 104: bore 120 mm, OD 170 mm, height 39 mm; weight 2650 g. Load figures from SKF 17000: dynamic 127 kN, static 390 kN, fatigue limit 11.8 kN; reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51224 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 24 decodes to 120 mm (code 24 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "Can 51224 carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 120 mm shaft must go to a separate radial bearing; mixed loading through 51224 edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51224-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 120×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51224",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51224"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51324-M",
    "brand": "SKF",
    "manufacturer_designation": "51324 M",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 120,
    "D_mm": 210,
    "B_mm": 70,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 325,
    "static_load_kN": 980,
    "fatigue_load_limit_kN": 28.5,
    "reference_speed_rpm": 1100,
    "limiting_speed_rpm": 1500,
    "max_rpm": 1500,
    "weight_g": 11000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51324 M is SKF's 120 mm-bore single-direction thrust ball bearing in the 51300 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 120×210×70 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 24 encode the bore as 120 mm (code 24 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 120×210×70 mm (4.724×8.268×2.756 in), 45.0 mm radial section, C 325 kN, C0 980 kN, Pu 28.5 kN. reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical), catalogue mass 11000 g. Pitch-diameter arithmetic: dm = (120+210)/2 = 165.0 mm; at the 1,500 r/min limiting speed that corresponds to roughly 248k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Speed-ratio note for this exact unit: the reference speed is 1,100 r/min against a 1,500 r/min limiting speed, a reference-to-limit ratio of 0.73. Envelope economics: the 70 mm axial height over a 45.0 mm radial section yields 4.6 kN of dynamic capacity per height millimetre, and the bearing weighs 11000 g for 325 kN C — about 34 g per rated kN. Light-load floor: Pu = 28.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51324 M; the number is 9 % of the 325 kN dynamic rating. Static-first selection data: 980 kN C0 spread across the 70 mm stack gives 14.0 kN of static rating per height millimetre, and the 11000 g mass/C0 ratio is about 11 g per static kN — crane-hook and screw positions are normally sized on these two figures. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 11000 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 120 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "offshore and dock winch drums",
      "heavy converter and ladle-tilt pivots",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume"
    ],
    "pitfalls": [
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 120 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 70 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "When the housing seat cannot be machined square to the 120 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51300 bearing.",
      "The 325/980 kN figures belong to 51324 M specifically (the single flat brass execution of 51324); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51324-M?",
        "a": "51324 M measures 120 mm bore × 210 mm OD × 70 mm bearing height (4.724 × 8.268 × 2.756 in), mass about 11000 g. SKF 17000 ratings: C 325 kN, C0 980 kN, Pu 28.5 kN, reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51324 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 24 encode the bore as 120 mm (code 24 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 120 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51324 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51324",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 120×210×70 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51324",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51324-M",
      "51324 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51424-M",
    "brand": "SKF",
    "manufacturer_designation": "51424 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 120,
    "D_mm": 250,
    "B_mm": 102,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 432,
    "static_load_kN": 1320,
    "fatigue_load_limit_kN": 36,
    "reference_speed_rpm": 800,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "weight_g": 25500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51424 M is an ISO 104 single-direction thrust ball bearing, 120 mm bore and 250 mm OD on a flat housing seat, standing 102 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 24: bore 120 mm (code 24 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 120×250×102 mm (4.724×9.843×4.016 in), 65.0 mm radial section, C 432 kN, C0 1320 kN, Pu 36 kN. reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical), catalogue mass 25500 g. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 16 at the 1,100 r/min limiting speed raises the required axial preload to about 662.6 kN; the reference-speed value 350.5 kN is the thermal design point. Load balance: C0 1320 kN against C 432 kN gives a 3.06 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 36 kN enters the adjusted-life check. Bore-to-OD planning: OD 250 over bore 120 is a 2.08× step for this size, and the 102 mm height gives a bore/height ratio of 1.18; use these ratios when the housing recess around the 120 mm shaft is the first constraint. Minimum-load arithmetic: with dm ≈ 185.0 mm and factor A 16, Fam ≈ A·(n·dm/1000)² at the 800 r/min reference speed is about 350.5 kN for 51424 M; below that preload the balls skid and smear the tracks. Sizing arithmetic on the 120 mm bore: 432 kN C over the 65.0 mm radial section gives 6.6 kN per section millimetre, and the 102 mm stack height is 1.57× that section — proportions typical of a 51400 thrust section. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51424 M adds a small amount of mass and cage strength without changing the 120×250×102 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,100 r/min ceiling.",
    "applications": [
      "very heavy crane and ladle hooks",
      "large press rams and screwdown mechanisms",
      "offshore and dock winch drums"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 16; for 51424 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51424 against two-way load lifts the loose washer off its raceway.",
      "The 51424 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 120 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Ordering discipline for 51424: the catalogue page quotes 51424 M and its 432/1320 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51424-M?",
        "a": "The catalogue envelope is 120×250×102 mm, mass 25500 g; ratings C 432 kN / C0 1320 kN / Pu 36 kN, reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51424 M mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 24: bore 120 mm (code 24 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51424-M carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 120 mm shaft must go to a separate radial bearing; mixed loading through 51424 M edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51424",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51424-M",
      "51424 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51126",
    "brand": "SKF",
    "manufacturer_designation": "51126",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 130,
    "D_mm": 170,
    "B_mm": 30,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 119,
    "static_load_kN": 440,
    "fatigue_load_limit_kN": 13.4,
    "reference_speed_rpm": 1900,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 1850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51126 is SKF's 130 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 130×170×30 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 26 encode the bore as 130 mm (code 26 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 130×170×30 mm (5.118×6.693×1.181 in), 20.0 mm radial section, C 119 kN, C0 440 kN, Pu 13.4 kN. reference speed 1,900 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 1850 g. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.94 at the 2,600 r/min limiting speed raises the required axial preload to about 143.0 kN; the reference-speed value 76.4 kN is the thermal design point. Mass and section check: 1850 g inside the 130×170×30 mm outline leaves a 20.0 mm radial section, and the 440 kN static rating is 3.70× the dynamic rating — plan static safety and minimum preload against those figures. At the printed limiting speed of 2,600 r/min the mean pitch diameter dm ≈ 150.0 mm implies a dn value around 390k mm·r/min; the 1,900 r/min reference speed is the thermal-planning value under catalogue load. Sizing arithmetic on the 130 mm bore: 119 kN C over the 20.0 mm radial section gives 6.0 kN per section millimetre, and the 30 mm stack height is 1.50× that section — proportions typical of a 51100 thrust section. Speed band width for this size is 700 r/min between reference and limiting (1.37× ratio); lubrication, preload and heat removal decide where inside that band 51126 can actually run. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 130 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 119/440 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "offshore and dock winch drums",
      "heavy converter and ladle-tilt pivots",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The 51126 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 130 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 119/440 kN and the available 170 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 119 kN track before first rotation.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51126 as the single flat pressed steel execution; other order numbers of the 51126 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51126?",
        "a": "51126 measures 130 mm bore × 170 mm OD × 30 mm bearing height (5.118 × 6.693 × 1.181 in), mass about 1850 g. SKF 17000 ratings: C 119 kN, C0 440 kN, Pu 13.4 kN, reference speed 1,900 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51126 mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 26 encode the bore as 130 mm (code 26 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51126 need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 0.94 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51126-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 130×170×30 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51126",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51126"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51226",
    "brand": "SKF",
    "manufacturer_designation": "51226",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 130,
    "D_mm": 190,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 186,
    "static_load_kN": 585,
    "fatigue_load_limit_kN": 17,
    "reference_speed_rpm": 1400,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "weight_g": 4000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51226 is an ISO 104 single-direction thrust ball bearing, 130 mm bore and 190 mm OD on a flat housing seat, standing 45 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 26: bore 130 mm (code 26 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 130×190×45 mm (5.118×7.48×1.772 in), 30.0 mm radial section, C 186 kN, C0 585 kN, Pu 17 kN. reference speed 1,400 r/min (thermal) and limiting speed 2,000 r/min (mechanical), catalogue mass 4000 g. At the printed limiting speed of 2,000 r/min the mean pitch diameter dm ≈ 160.0 mm implies a dn value around 320k mm·r/min; the 1,400 r/min reference speed is the thermal-planning value under catalogue load. Selection figures for 51226: the C0/C ratio is 3.15, Pu 17 kN is about 9 % of C, and the catalogue mass works out to roughly 31 g per millimetre of bore; the printed minimum-load factor is A 1.8. Mass and section check: 4000 g inside the 130×190×45 mm outline leaves a 30.0 mm radial section, and the 585 kN static rating is 3.15× the dynamic rating — plan static safety and minimum preload against those figures. Imperial cross-check for procurement drawings: 5.118 in bore, 7.48 in OD, 1.772 in height, and the 4000 g catalogue mass converts to 4.000 kg (141.1 oz). Rating split for documentation: dynamic 186 kN (L10 life), static 585 kN (safety factor s0), fatigue limit 17 kN (adjusted life) — three different uses of three different numbers for 51226, none interchangeable with another. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 130 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 186/585 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "marine gearbox thrust positions",
      "large press rams and screwdown mechanisms",
      "heavy converter and ladle-tilt pivots"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 186 kN track before first rotation.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 186/585 kN and the available 190 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 51226 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 130 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 1.8; for 51226 a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 186/585 kN figures belong to 51226 specifically (the single flat pressed steel execution of 51226); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51226?",
        "a": "The catalogue envelope is 130×190×45 mm, mass 4000 g; ratings C 186 kN / C0 585 kN / Pu 17 kN, reference speed 1,400 r/min (thermal) and limiting speed 2,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51226 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 26: bore 130 mm (code 26 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51226 lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 2,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51226-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "51226",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51226"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51326-M",
    "brand": "SKF",
    "manufacturer_designation": "51326 M",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 130,
    "D_mm": 225,
    "B_mm": 75,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 358,
    "static_load_kN": 1140,
    "fatigue_load_limit_kN": 32,
    "reference_speed_rpm": 1000,
    "limiting_speed_rpm": 1400,
    "max_rpm": 1400,
    "weight_g": 13000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51300 series order number 51326 M is a SKF single-direction thrust ball bearing for a 130 mm seat, built to ISO 104, with a flat housing seating surface, 130×225×75 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 26 decodes to 130 mm (code 26 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 130×225×75 mm (5.118×8.858×2.953 in), 47.5 mm radial section, C 358 kN, C0 1140 kN, Pu 32 kN. reference speed 1,000 r/min (thermal) and limiting speed 1,400 r/min (mechanical), catalogue mass 13000 g. Load balance: C0 1140 kN against C 358 kN gives a 3.18 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 32 kN enters the adjusted-life check. At the printed limiting speed of 1,400 r/min the mean pitch diameter dm ≈ 177.5 mm implies a dn value around 249k mm·r/min; the 1,000 r/min reference speed is the thermal-planning value under catalogue load. Sizing arithmetic on the 130 mm bore: 358 kN C over the 47.5 mm radial section gives 7.5 kN per section millimetre, and the 75 mm stack height is 1.58× that section — proportions typical of a 51300 thrust section. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 6.8 at the 1,400 r/min limiting speed raises the required axial preload to about 419.9 kN; the reference-speed value 214.2 kN is the thermal design point. Bore-to-OD planning: OD 225 over bore 130 is a 1.73× step for this size, and the 75 mm height gives a bore/height ratio of 1.73; use these ratios when the housing recess around the 130 mm shaft is the first constraint. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 13000 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 130 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "offshore and dock winch drums",
      "very heavy crane and ladle hooks",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 6.8; for 51326 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 51326 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 130 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 358/1140 kN and the available 225 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 130 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Ordering discipline for 51326: the catalogue page quotes 51326 M and its 358/1140 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51326-M?",
        "a": "Boundary dimensions to ISO 104: bore 130 mm, OD 225 mm, height 75 mm; weight 13000 g. Load figures from SKF 17000: dynamic 358 kN, static 1140 kN, fatigue limit 32 kN; reference speed 1,000 r/min (thermal) and limiting speed 1,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51326 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 26 decodes to 130 mm (code 26 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51326-M?",
        "a": "The 1,000 r/min reference speed is the thermal balance under catalogue load; the 1,400 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51326-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 6.8 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51326",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 130×225×75 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51326",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51326-M",
      "51326 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51426-M",
    "brand": "SKF",
    "manufacturer_designation": "51426 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 130,
    "D_mm": 270,
    "B_mm": 110,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 520,
    "static_load_kN": 1730,
    "fatigue_load_limit_kN": 45,
    "reference_speed_rpm": 750,
    "limiting_speed_rpm": 1000,
    "max_rpm": 1000,
    "weight_g": 32000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51426 M is SKF's 130 mm-bore single-direction thrust ball bearing in the 51400 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 130×270×110 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 26 encode the bore as 130 mm (code 26 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 130×270×110 mm (5.118×10.63×4.331 in), 70.0 mm radial section, C 520 kN, C0 1730 kN, Pu 45 kN. reference speed 750 r/min (thermal) and limiting speed 1,000 r/min (mechanical), catalogue mass 32000 g. Load balance: C0 1730 kN against C 520 kN gives a 3.33 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 45 kN enters the adjusted-life check. Capacity density: 520 kN C from 32.000 kg of bearing steel gives about 16.3 kN per kilogram; static density is correspondingly 54.1 kN/kg at C0 1730 kN. Imperial cross-check for procurement drawings: 5.118 in bore, 10.63 in OD, 4.331 in height, and the 32000 g catalogue mass converts to 32.000 kg (1128.7 oz). Mass and section check: 32000 g inside the 130×270×110 mm outline leaves a 70.0 mm radial section, and the 1730 kN static rating is 3.33× the dynamic rating — plan static safety and minimum preload against those figures. Rating split for documentation: dynamic 520 kN (L10 life), static 1730 kN (safety factor s0), fatigue limit 45 kN (adjusted life) — three different uses of three different numbers for 51426 M, none interchangeable with another. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51426 M adds a small amount of mass and cage strength without changing the 130×270×110 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,000 r/min ceiling.",
    "applications": [
      "very heavy crane and ladle hooks",
      "offshore and dock winch drums",
      "heavy converter and ladle-tilt pivots"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "track rust staining from condensate during long idle periods in humid plant air",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 110 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 130 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 520 kN track before first rotation.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51426 M as the single flat brass execution; other order numbers of the 51426 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51426-M?",
        "a": "51426 M measures 130 mm bore × 270 mm OD × 110 mm bearing height (5.118 × 10.63 × 4.331 in), mass about 32000 g. SKF 17000 ratings: C 520 kN, C0 1730 kN, Pu 45 kN, reference speed 750 r/min (thermal) and limiting speed 1,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51426 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 26 encode the bore as 130 mm (code 26 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51426-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 16 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, M-cage product) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51426",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51426-M",
      "51426 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51128",
    "brand": "SKF",
    "manufacturer_designation": "51128",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 140,
    "D_mm": 180,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 111,
    "static_load_kN": 440,
    "fatigue_load_limit_kN": 12.9,
    "reference_speed_rpm": 1800,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 2050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51128 is a SKF single-direction thrust ball bearing for a 140 mm seat, built to ISO 104, with a flat housing seating surface, 140×180×31 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 28 decodes to 140 mm (code 28 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 140×180×31 mm (5.512×7.087×1.22 in), 20.0 mm radial section, C 111 kN, C0 440 kN, Pu 12.9 kN. reference speed 1,800 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 2050 g. Stack/annulus proportions: the 31 mm axial stack over the 10,053 mm² washer annulus gives 3.08 mm of height per annular square millimetre ×10⁻³, and at 2050 g the bearing holds about 214.6 kN of C0 per kilogram. Pitch-diameter arithmetic: dm = (140+180)/2 = 160.0 mm; at the 2,600 r/min limiting speed that corresponds to roughly 416k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Section proportions: the 20.0 mm radial section compares with 140 mm of bore (section/bore ≈ 0.14) and the 31 mm height is 1.55× that section — the proportions that identify the 51100 envelope at a glance. Rating split for documentation: dynamic 111 kN (L10 life), static 440 kN (safety factor s0), fatigue limit 12.9 kN (adjusted life) — three different uses of three different numbers for 51128, none interchangeable with another. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 1 at the 2,600 r/min limiting speed raises the required axial preload to about 173.1 kN; the reference-speed value 82.9 kN is the thermal design point. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 140 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 111/440 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "marine gearbox thrust positions",
      "heavy converter and ladle-tilt pivots",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 31 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The 51128 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 140 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 111/440 kN and the available 180 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51128 as the single flat pressed steel execution; other order numbers of the 51128 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51128?",
        "a": "Boundary dimensions to ISO 104: bore 140 mm, OD 180 mm, height 31 mm; weight 2050 g. Load figures from SKF 17000: dynamic 111 kN, static 440 kN, fatigue limit 12.9 kN; reference speed 1,800 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51128 mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 28 decodes to 140 mm (code 28 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51128 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51128?",
        "a": "The 1,800 r/min reference speed is the thermal balance under catalogue load; the 2,600 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51128-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 140×180×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51128",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51128"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51228",
    "brand": "SKF",
    "manufacturer_designation": "51228",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 140,
    "D_mm": 200,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 190,
    "static_load_kN": 620,
    "fatigue_load_limit_kN": 17.6,
    "reference_speed_rpm": 1400,
    "limiting_speed_rpm": 1900,
    "max_rpm": 1900,
    "weight_g": 4350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51228 is an ISO 104 single-direction thrust ball bearing, 140 mm bore and 200 mm OD on a flat housing seat, standing 46 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 28: bore 140 mm (code 28 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 140×200×46 mm (5.512×7.874×1.811 in), 30.0 mm radial section, C 190 kN, C0 620 kN, Pu 17.6 kN. reference speed 1,400 r/min (thermal) and limiting speed 1,900 r/min (mechanical), catalogue mass 4350 g. Imperial cross-check for procurement drawings: 5.512 in bore, 7.874 in OD, 1.811 in height, and the 4350 g catalogue mass converts to 4.350 kg (153.4 oz). Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 1,900 r/min while thermal balance under catalogue load sets the 1,400 r/min reference; at dm ≈ 170.0 mm the corresponding dn is approximately 323k mm·r/min. At the printed limiting speed of 1,900 r/min the mean pitch diameter dm ≈ 170.0 mm implies a dn value around 323k mm·r/min; the 1,400 r/min reference speed is the thermal-planning value under catalogue load. Stack/annulus proportions: the 46 mm axial stack over the 16,022 mm² washer annulus gives 2.87 mm of height per annular square millimetre ×10⁻³, and at 4350 g the bearing holds about 142.5 kN of C0 per kilogram. Track-circle loading: per millimetre of mean track circumference the 190 kN dynamic rating corresponds to roughly 0.36 kN/mm of π·dm track, a useful comparison against the other dimension series of the 140 mm bore. Execution note for this order number: the flat housing seating surface must be machined square to the shaft axis and supported across the full washer face — unlike the sphered 53-series execution this pressed-cage 51-series bearing has no self-aligning capability at all, so seat squareness is checked at mounting, not compensated in service. On this 140 mm size the pressed cage and separable washers make the bearing interchangeable across brands on the ISO 104 plan, but the SKF ratings 190/620 kN are this catalogue's figures — confirm the replacement order's ratings rather than swapping on envelope alone.",
    "applications": [
      "offshore and dock winch drums",
      "marine gearbox thrust positions",
      "very heavy crane and ladle hooks"
    ],
    "failure_modes": [
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "pressed sheet-steel cage distortion after a mounting blow or shock load at sizes where the F/M machined-cage executions are the catalogue choice",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 140 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "The 51228 is a pure axial bearing: it must never be subjected to radial load — any radial force on the 140 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51228 against two-way load lifts the loose washer off its raceway.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 190 kN track before first rotation.",
      "Ordering discipline for 51228: the catalogue page quotes 51228 and its 190/620 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51228?",
        "a": "The catalogue envelope is 140×200×46 mm, mass 4350 g; ratings C 190 kN / C0 620 kN / Pu 17.6 kN, reference speed 1,400 r/min (thermal) and limiting speed 1,900 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51228 mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 28: bore 140 mm (code 28 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 140 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51228 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51228-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "51228",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51228"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51328-M",
    "brand": "SKF",
    "manufacturer_designation": "51328 M",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 140,
    "D_mm": 240,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 377,
    "static_load_kN": 1220,
    "fatigue_load_limit_kN": 32.5,
    "reference_speed_rpm": 950,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "weight_g": 15500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51300 series order number 51328 M is a SKF single-direction thrust ball bearing for a 140 mm seat, built to ISO 104, with a flat housing seating surface, 140×240×80 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 28 decodes to 140 mm (code 28 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 140×240×80 mm (5.512×9.449×3.15 in), 50.0 mm radial section, C 377 kN, C0 1220 kN, Pu 32.5 kN. reference speed 950 r/min (thermal) and limiting speed 1,300 r/min (mechanical), catalogue mass 15500 g. Bore-to-OD planning: OD 240 over bore 140 is a 1.71× step for this size, and the 80 mm height gives a bore/height ratio of 1.75; use these ratios when the housing recess around the 140 mm shaft is the first constraint. Section proportions: the 50.0 mm radial section compares with 140 mm of bore (section/bore ≈ 0.36) and the 80 mm height is 1.60× that section — the proportions that identify the 51300 envelope at a glance. Minimum-load arithmetic: with dm ≈ 190.0 mm and factor A 9.1, Fam ≈ A·(n·dm/1000)² at the 950 r/min reference speed is about 296.5 kN for 51328 M; below that preload the balls skid and smear the tracks. At the printed limiting speed of 1,300 r/min the mean pitch diameter dm ≈ 190.0 mm implies a dn value around 247k mm·r/min; the 950 r/min reference speed is the thermal-planning value under catalogue load. Pitch-diameter arithmetic: dm = (140+240)/2 = 190.0 mm; at the 1,300 r/min limiting speed that corresponds to roughly 247k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51328 M adds a small amount of mass and cage strength without changing the 140×240×80 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,300 r/min ceiling.",
    "applications": [
      "offshore and dock winch drums",
      "very heavy crane and ladle hooks",
      "heavy converter and ladle-tilt pivots"
    ],
    "failure_modes": [
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 80 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 377/1220 kN and the available 240 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 51328 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 140 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The 377/1220 kN figures belong to 51328 M specifically (the single flat brass execution of 51328); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51328-M?",
        "a": "Boundary dimensions to ISO 104: bore 140 mm, OD 240 mm, height 80 mm; weight 15500 g. Load figures from SKF 17000: dynamic 377 kN, static 1220 kN, fatigue limit 32.5 kN; reference speed 950 r/min (thermal) and limiting speed 1,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51328 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 28 decodes to 140 mm (code 28 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, M-cage product) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "Can 51328-M carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 140 mm shaft must go to a separate radial bearing; mixed loading through 51328 M edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51328",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 140×240×80 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51328",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51328-M",
      "51328 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51428-M",
    "brand": "SKF",
    "manufacturer_designation": "51428 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 140,
    "D_mm": 280,
    "B_mm": 112,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 520,
    "static_load_kN": 1730,
    "fatigue_load_limit_kN": 44,
    "reference_speed_rpm": 700,
    "limiting_speed_rpm": 1000,
    "max_rpm": 1000,
    "weight_g": 34500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51428 M is SKF's 140 mm-bore single-direction thrust ball bearing in the 51400 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 140×280×112 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 28 encode the bore as 140 mm (code 28 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 140×280×112 mm (5.512×11.024×4.409 in), 70.0 mm radial section, C 520 kN, C0 1730 kN, Pu 44 kN. reference speed 700 r/min (thermal) and limiting speed 1,000 r/min (mechanical), catalogue mass 34500 g. Speed band width for this size is 300 r/min between reference and limiting (1.43× ratio); lubrication, preload and heat removal decide where inside that band 51428 M can actually run. Sizing arithmetic on the 140 mm bore: 520 kN C over the 70.0 mm radial section gives 7.4 kN per section millimetre, and the 112 mm stack height is 1.60× that section — proportions typical of a 51400 thrust section. Section proportions: the 70.0 mm radial section compares with 140 mm of bore (section/bore ≈ 0.50) and the 112 mm height is 1.60× that section — the proportions that identify the 51400 envelope at a glance. Mass and section check: 34500 g inside the 140×280×112 mm outline leaves a 70.0 mm radial section, and the 1730 kN static rating is 3.33× the dynamic rating — plan static safety and minimum preload against those figures. Bore-to-OD planning: OD 280 over bore 140 is a 2.00× step for this size, and the 112 mm height gives a bore/height ratio of 1.25; use these ratios when the housing recess around the 140 mm shaft is the first constraint. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51428 M adds a small amount of mass and cage strength without changing the 140×280×112 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,000 r/min ceiling.",
    "applications": [
      "marine gearbox thrust positions",
      "very heavy crane and ladle hooks",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 16; for 51428 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 112 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 520 kN track before first rotation.",
      "The 51428 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 140 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Ordering discipline for 51428: the catalogue page quotes 51428 M and its 520/1730 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51428-M?",
        "a": "51428 M measures 140 mm bore × 280 mm OD × 112 mm bearing height (5.512 × 11.024 × 4.409 in), mass about 34500 g. SKF 17000 ratings: C 520 kN, C0 1730 kN, Pu 44 kN, reference speed 700 r/min (thermal) and limiting speed 1,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51428 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 28 encode the bore as 140 mm (code 28 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51428 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51428-M?",
        "a": "The 700 r/min reference speed is the thermal balance under catalogue load; the 1,000 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51428",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51428-M",
      "51428 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51130-M",
    "brand": "SKF",
    "manufacturer_designation": "51130 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 150,
    "D_mm": 190,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 111,
    "static_load_kN": 440,
    "fatigue_load_limit_kN": 12.5,
    "reference_speed_rpm": 1700,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 2200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51130 M is SKF's 150 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 150×190×31 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 30 encode the bore as 150 mm (code 30 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 150×190×31 mm (5.906×7.48×1.22 in), 20.0 mm radial section, C 111 kN, C0 440 kN, Pu 12.5 kN. reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 2200 g. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51130 M covers about 10,681 mm², distributing C0 440 kN over a mean track circle of π·dm ≈ 534 mm. Rating split for documentation: dynamic 111 kN (L10 life), static 440 kN (safety factor s0), fatigue limit 12.5 kN (adjusted life) — three different uses of three different numbers for 51130 M, none interchangeable with another. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 1 at the 2,400 r/min limiting speed raises the required axial preload to about 166.5 kN; the reference-speed value 83.5 kN is the thermal design point. Load balance: C0 440 kN against C 111 kN gives a 3.96 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 12.5 kN enters the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 1,700 r/min against a 2,400 r/min limiting speed, a reference-to-limit ratio of 0.71. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 2200 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 150 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "very heavy crane and ladle hooks",
      "heavy converter and ladle-tilt pivots"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 150 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 1; for 51130 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 150 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The 51130 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 150 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Ordering discipline for 51130: the catalogue page quotes 51130 M and its 111/440 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51130-M?",
        "a": "51130 M measures 150 mm bore × 190 mm OD × 31 mm bearing height (5.906 × 7.48 × 1.22 in), mass about 2200 g. SKF 17000 ratings: C 111 kN, C0 440 kN, Pu 12.5 kN, reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51130 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 30 encode the bore as 150 mm (code 30 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51130-M lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 2,400 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 150 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51130",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "51130",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51130-M",
      "51130 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51230-M",
    "brand": "SKF",
    "manufacturer_designation": "51230 M",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 150,
    "D_mm": 215,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 238,
    "static_load_kN": 800,
    "fatigue_load_limit_kN": 22,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "weight_g": 6100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51230 M is an ISO 104 single-direction thrust ball bearing, 150 mm bore and 215 mm OD on a flat housing seat, standing 50 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 30: bore 150 mm (code 30 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 150×215×50 mm (5.906×8.465×1.969 in), 32.5 mm radial section, C 238 kN, C0 800 kN, Pu 22 kN. reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical), catalogue mass 6100 g. Rating split for documentation: dynamic 238 kN (L10 life), static 800 kN (safety factor s0), fatigue limit 22 kN (adjusted life) — three different uses of three different numbers for 51230 M, none interchangeable with another. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51230 M covers about 18,634 mm², distributing C0 800 kN over a mean track circle of π·dm ≈ 573 mm. Light-load floor: Pu = 22 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51230 M; the number is 9 % of the 238 kN dynamic rating. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 3.3 at the 1,800 r/min limiting speed raises the required axial preload to about 356.1 kN; the reference-speed value 185.7 kN is the thermal design point. Speed-ratio note for this exact unit: the reference speed is 1,300 r/min against a 1,800 r/min limiting speed, a reference-to-limit ratio of 0.72. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 6100 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 150 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "heavy converter and ladle-tilt pivots",
      "very heavy crane and ladle hooks",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 50 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51230 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 150 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51230 M as the single flat brass execution; other order numbers of the 51230 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51230-M?",
        "a": "The catalogue envelope is 150×215×50 mm, mass 6100 g; ratings C 238 kN / C0 800 kN / Pu 22 kN, reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51230 M mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 30: bore 150 mm (code 30 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51230-M?",
        "a": "The 1,300 r/min reference speed is the thermal balance under catalogue load; the 1,800 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51230-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 3.3 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51230",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 150×215×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51230",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51230-M",
      "51230 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51330-M",
    "brand": "SKF",
    "manufacturer_designation": "51330 M",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 150,
    "D_mm": 250,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 390,
    "static_load_kN": 1290,
    "fatigue_load_limit_kN": 34,
    "reference_speed_rpm": 900,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "weight_g": 16500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51300 series order number 51330 M is a SKF single-direction thrust ball bearing for a 150 mm seat, built to ISO 104, with a flat housing seating surface, 150×250×80 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 30 decodes to 150 mm (code 30 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 150×250×80 mm (5.906×9.843×3.15 in), 50.0 mm radial section, C 390 kN, C0 1290 kN, Pu 34 kN. reference speed 900 r/min (thermal) and limiting speed 1,300 r/min (mechanical), catalogue mass 16500 g. Capacity density: 390 kN C from 16.500 kg of bearing steel gives about 23.6 kN per kilogram; static density is correspondingly 78.2 kN/kg at C0 1290 kN. Pitch-diameter arithmetic: dm = (150+250)/2 = 200.0 mm; at the 1,300 r/min limiting speed that corresponds to roughly 260k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Static-first selection data: 1290 kN C0 spread across the 80 mm stack gives 16.1 kN of static rating per height millimetre, and the 16500 g mass/C0 ratio is about 13 g per static kN — crane-hook and screw positions are normally sized on these two figures. Sizing arithmetic on the 150 mm bore: 390 kN C over the 50.0 mm radial section gives 7.8 kN per section millimetre, and the 80 mm stack height is 1.60× that section — proportions typical of a 51300 thrust section. Track-circle loading: per millimetre of mean track circumference the 390 kN dynamic rating corresponds to roughly 0.62 kN/mm of π·dm track, a useful comparison against the other dimension series of the 150 mm bore. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51330 M adds a small amount of mass and cage strength without changing the 150×250×80 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,300 r/min ceiling.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "very heavy crane and ladle hooks",
      "offshore and dock winch drums"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 150 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 390/1290 kN and the available 250 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "When the housing seat cannot be machined square to the 150 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51300 bearing.",
      "The 390/1290 kN figures belong to 51330 M specifically (the single flat brass execution of 51330); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51330-M?",
        "a": "Boundary dimensions to ISO 104: bore 150 mm, OD 250 mm, height 80 mm; weight 16500 g. Load figures from SKF 17000: dynamic 390 kN, static 1290 kN, fatigue limit 34 kN; reference speed 900 r/min (thermal) and limiting speed 1,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51330 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 30 decodes to 150 mm (code 30 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51330-M carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 150 mm shaft must go to a separate radial bearing; mixed loading through 51330 M edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51330",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 150×250×80 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51330",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51330-M",
      "51330 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51430-M",
    "brand": "SKF",
    "manufacturer_designation": "51430 M",
    "series": "51400-series",
    "type": "thrust_ball",
    "d_mm": 150,
    "D_mm": 300,
    "B_mm": 120,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 559,
    "static_load_kN": 1960,
    "fatigue_load_limit_kN": 48,
    "reference_speed_rpm": 670,
    "limiting_speed_rpm": 950,
    "max_rpm": 950,
    "weight_g": 42500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51400 series order number 51430 M is a SKF single-direction thrust ball bearing for a 150 mm seat, built to ISO 104, with a flat housing seating surface, 150×300×120 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 30 decodes to 150 mm (code 30 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 150×300×120 mm (5.906×11.811×4.724 in), 75.0 mm radial section, C 559 kN, C0 1960 kN, Pu 48 kN. reference speed 670 r/min (thermal) and limiting speed 950 r/min (mechanical), catalogue mass 42500 g. Envelope economics: the 120 mm axial height over a 75.0 mm radial section yields 4.7 kN of dynamic capacity per height millimetre, and the bearing weighs 42500 g for 559 kN C — about 76 g per rated kN. Selection figures for 51430 M: the C0/C ratio is 3.51, Pu 48 kN is about 9 % of C, and the catalogue mass works out to roughly 283 g per millimetre of bore; the printed minimum-load factor is A 20. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51430 M covers about 53,014 mm², distributing C0 1960 kN over a mean track circle of π·dm ≈ 707 mm. Speed band width for this size is 280 r/min between reference and limiting (1.42× ratio); lubrication, preload and heat removal decide where inside that band 51430 M can actually run. Section proportions: the 75.0 mm radial section compares with 150 mm of bore (section/bore ≈ 0.50) and the 120 mm height is 1.60× that section — the proportions that identify the 51400 envelope at a glance. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51430 M adds a small amount of mass and cage strength without changing the 150×300×120 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 950 r/min ceiling.",
    "applications": [
      "very heavy crane and ladle hooks",
      "large press rams and screwdown mechanisms",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face"
    ],
    "pitfalls": [
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 150 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 20; for 51430 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "When the housing seat cannot be machined square to the 150 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51400 bearing.",
      "The 559/1960 kN figures belong to 51430 M specifically (the single flat brass execution of 51430); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51430-M?",
        "a": "Boundary dimensions to ISO 104: bore 150 mm, OD 300 mm, height 120 mm; weight 42500 g. Load figures from SKF 17000: dynamic 559 kN, static 1960 kN, fatigue limit 48 kN; reference speed 670 r/min (thermal) and limiting speed 950 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51430 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 30 decodes to 150 mm (code 30 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 150 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51430 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51430",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51430-M",
      "51430 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51132-M",
    "brand": "SKF",
    "manufacturer_designation": "51132 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 160,
    "D_mm": 200,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 112,
    "static_load_kN": 465,
    "fatigue_load_limit_kN": 12.9,
    "reference_speed_rpm": 1700,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 2350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51132 M is a SKF single-direction thrust ball bearing for a 160 mm seat, built to ISO 104, with a flat housing seating surface, 160×200×31 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 32 decodes to 160 mm (code 32 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 160×200×31 mm (6.299×7.874×1.22 in), 20.0 mm radial section, C 112 kN, C0 465 kN, Pu 12.9 kN. reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 2350 g. Envelope economics: the 31 mm axial height over a 20.0 mm radial section yields 3.6 kN of dynamic capacity per height millimetre, and the bearing weighs 2350 g for 112 kN C — about 21 g per rated kN. Rating split for documentation: dynamic 112 kN (L10 life), static 465 kN (safety factor s0), fatigue limit 12.9 kN (adjusted life) — three different uses of three different numbers for 51132 M, none interchangeable with another. Stack/annulus proportions: the 31 mm axial stack over the 11,310 mm² washer annulus gives 2.74 mm of height per annular square millimetre ×10⁻³, and at 2350 g the bearing holds about 197.9 kN of C0 per kilogram. Speed band width for this size is 700 r/min between reference and limiting (1.41× ratio); lubrication, preload and heat removal decide where inside that band 51132 M can actually run. Sizing arithmetic on the 160 mm bore: 112 kN C over the 20.0 mm radial section gives 5.6 kN per section millimetre, and the 31 mm stack height is 1.55× that section — proportions typical of a 51100 thrust section. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 2350 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 160 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "marine gearbox thrust positions",
      "very heavy crane and ladle hooks"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "The 51132 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 160 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 31 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "When the housing seat cannot be machined square to the 160 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 112/465 kN and the available 200 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51132 M as the single flat brass execution; other order numbers of the 51132 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51132-M?",
        "a": "Boundary dimensions to ISO 104: bore 160 mm, OD 200 mm, height 31 mm; weight 2350 g. Load figures from SKF 17000: dynamic 112 kN, static 465 kN, fatigue limit 12.9 kN; reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51132 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 32 decodes to 160 mm (code 32 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51132 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51132-M?",
        "a": "The 1,700 r/min reference speed is the thermal balance under catalogue load; the 2,400 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51132",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "51132",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51132-M",
      "51132 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51232-M",
    "brand": "SKF",
    "manufacturer_designation": "51232 M",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 160,
    "D_mm": 225,
    "B_mm": 51,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 238,
    "static_load_kN": 830,
    "fatigue_load_limit_kN": 22.4,
    "reference_speed_rpm": 1200,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "weight_g": 6550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51232 M is a SKF single-direction thrust ball bearing for a 160 mm seat, built to ISO 104, with a flat housing seating surface, 160×225×51 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 32 decodes to 160 mm (code 32 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 160×225×51 mm (6.299×8.858×2.008 in), 32.5 mm radial section, C 238 kN, C0 830 kN, Pu 22.4 kN. reference speed 1,200 r/min (thermal) and limiting speed 1,700 r/min (mechanical), catalogue mass 6550 g. Capacity density: 238 kN C from 6.550 kg of bearing steel gives about 36.3 kN per kilogram; static density is correspondingly 126.7 kN/kg at C0 830 kN. Selection figures for 51232 M: the C0/C ratio is 3.49, Pu 22.4 kN is about 9 % of C, and the catalogue mass works out to roughly 41 g per millimetre of bore; the printed minimum-load factor is A 3.8. Minimum-load arithmetic: with dm ≈ 192.5 mm and factor A 3.8, Fam ≈ A·(n·dm/1000)² at the 1,200 r/min reference speed is about 202.8 kN for 51232 M; below that preload the balls skid and smear the tracks. Pitch-diameter arithmetic: dm = (160+225)/2 = 192.5 mm; at the 1,700 r/min limiting speed that corresponds to roughly 327k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Speed-ratio note for this exact unit: the reference speed is 1,200 r/min against a 1,700 r/min limiting speed, a reference-to-limit ratio of 0.71. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 6550 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 160 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "offshore and dock winch drums",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 51 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 3.8; for 51232 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "When the housing seat cannot be machined square to the 160 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 238 kN track before first rotation.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51232 M as the single flat brass execution; other order numbers of the 51232 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51232-M?",
        "a": "Boundary dimensions to ISO 104: bore 160 mm, OD 225 mm, height 51 mm; weight 6550 g. Load figures from SKF 17000: dynamic 238 kN, static 830 kN, fatigue limit 22.4 kN; reference speed 1,200 r/min (thermal) and limiting speed 1,700 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51232 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 32 decodes to 160 mm (code 32 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 160 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51232 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51232",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 160×225×51 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51232",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51232-M",
      "51232 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51332-M",
    "brand": "SKF",
    "manufacturer_designation": "51332 M",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 160,
    "D_mm": 270,
    "B_mm": 87,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 449,
    "static_load_kN": 1660,
    "fatigue_load_limit_kN": 41.5,
    "reference_speed_rpm": 850,
    "limiting_speed_rpm": 1200,
    "max_rpm": 1200,
    "weight_g": 21000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51300 series order number 51332 M is a SKF single-direction thrust ball bearing for a 160 mm seat, built to ISO 104, with a flat housing seating surface, 160×270×87 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 32 decodes to 160 mm (code 32 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 160×270×87 mm (6.299×10.63×3.425 in), 55.0 mm radial section, C 449 kN, C0 1660 kN, Pu 41.5 kN. reference speed 850 r/min (thermal) and limiting speed 1,200 r/min (mechanical), catalogue mass 21000 g. At the printed limiting speed of 1,200 r/min the mean pitch diameter dm ≈ 215.0 mm implies a dn value around 258k mm·r/min; the 850 r/min reference speed is the thermal-planning value under catalogue load. Minimum-load arithmetic: with dm ≈ 215.0 mm and factor A 14, Fam ≈ A·(n·dm/1000)² at the 850 r/min reference speed is about 467.6 kN for 51332 M; below that preload the balls skid and smear the tracks. Light-load floor: Pu = 41.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51332 M; the number is 9 % of the 449 kN dynamic rating. Mass and section check: 21000 g inside the 160×270×87 mm outline leaves a 55.0 mm radial section, and the 1660 kN static rating is 3.70× the dynamic rating — plan static safety and minimum preload against those figures. Speed band width for this size is 350 r/min between reference and limiting (1.41× ratio); lubrication, preload and heat removal decide where inside that band 51332 M can actually run. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 21000 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 160 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "very heavy crane and ladle hooks",
      "offshore and dock winch drums",
      "heavy converter and ladle-tilt pivots"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "track rust staining from condensate during long idle periods in humid plant air",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 449 kN track before first rotation.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 87 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 449/1660 kN and the available 270 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51332 against two-way load lifts the loose washer off its raceway.",
      "The 449/1660 kN figures belong to 51332 M specifically (the single flat brass execution of 51332); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51332-M?",
        "a": "Boundary dimensions to ISO 104: bore 160 mm, OD 270 mm, height 87 mm; weight 21000 g. Load figures from SKF 17000: dynamic 449 kN, static 1660 kN, fatigue limit 41.5 kN; reference speed 850 r/min (thermal) and limiting speed 1,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51332 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 32 decodes to 160 mm (code 32 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51332-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 14 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, M-cage product) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51332",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 160×270×87 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51332",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51332-M",
      "51332 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51134-M",
    "brand": "SKF",
    "manufacturer_designation": "51134 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 170,
    "D_mm": 215,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 133,
    "static_load_kN": 540,
    "fatigue_load_limit_kN": 14.3,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 3300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51134 M is a SKF single-direction thrust ball bearing for a 170 mm seat, built to ISO 104, with a flat housing seating surface, 170×215×34 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 34 decodes to 170 mm (code 34 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 170×215×34 mm (6.693×8.465×1.339 in), 22.5 mm radial section, C 133 kN, C0 540 kN, Pu 14.3 kN. reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 3300 g. Envelope economics: the 34 mm axial height over a 22.5 mm radial section yields 3.9 kN of dynamic capacity per height millimetre, and the bearing weighs 3300 g for 133 kN C — about 25 g per rated kN. Capacity density: 133 kN C from 3.300 kg of bearing steel gives about 40.3 kN per kilogram; static density is correspondingly 163.6 kN/kg at C0 540 kN. Pitch-diameter arithmetic: dm = (170+215)/2 = 192.5 mm; at the 2,200 r/min limiting speed that corresponds to roughly 424k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Track-circle loading: per millimetre of mean track circumference the 133 kN dynamic rating corresponds to roughly 0.22 kN/mm of π·dm track, a useful comparison against the other dimension series of the 170 mm bore. Minimum-load arithmetic: with dm ≈ 192.5 mm and factor A 1.5, Fam ≈ A·(n·dm/1000)² at the 1,600 r/min reference speed is about 142.3 kN for 51134 M; below that preload the balls skid and smear the tracks. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 3300 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 170 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "marine gearbox thrust positions",
      "very heavy crane and ladle hooks",
      "offshore and dock winch drums"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 170 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 133/540 kN and the available 215 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 1.5; for 51134 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 133/540 kN figures belong to 51134 M specifically (the single flat brass execution of 51134); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51134-M?",
        "a": "Boundary dimensions to ISO 104: bore 170 mm, OD 215 mm, height 34 mm; weight 3300 g. Load figures from SKF 17000: dynamic 133 kN, static 540 kN, fatigue limit 14.3 kN; reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51134 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 34 decodes to 170 mm (code 34 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51134-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 1.5 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, M-cage product) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51134",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "51134",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51134-M",
      "51134 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51234-M",
    "brand": "SKF",
    "manufacturer_designation": "51234 M",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 170,
    "D_mm": 240,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 270,
    "static_load_kN": 930,
    "fatigue_load_limit_kN": 24,
    "reference_speed_rpm": 1200,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "weight_g": 8150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51234 M is SKF's 170 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 170×240×55 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 34 encode the bore as 170 mm (code 34 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 170×240×55 mm (6.693×9.449×2.165 in), 35.0 mm radial section, C 270 kN, C0 930 kN, Pu 24 kN. reference speed 1,200 r/min (thermal) and limiting speed 1,700 r/min (mechanical), catalogue mass 8150 g. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 5.4 at the 1,700 r/min limiting speed raises the required axial preload to about 655.8 kN; the reference-speed value 326.8 kN is the thermal design point. Section proportions: the 35.0 mm radial section compares with 170 mm of bore (section/bore ≈ 0.21) and the 55 mm height is 1.57× that section — the proportions that identify the 51200 envelope at a glance. Mass and section check: 8150 g inside the 170×240×55 mm outline leaves a 35.0 mm radial section, and the 930 kN static rating is 3.44× the dynamic rating — plan static safety and minimum preload against those figures. Capacity density: 270 kN C from 8.150 kg of bearing steel gives about 33.1 kN per kilogram; static density is correspondingly 114.1 kN/kg at C0 930 kN. Track-circle loading: per millimetre of mean track circumference the 270 kN dynamic rating corresponds to roughly 0.42 kN/mm of π·dm track, a useful comparison against the other dimension series of the 170 mm bore. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 8150 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 170 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "very heavy crane and ladle hooks",
      "offshore and dock winch drums"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 170 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 170 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 270 kN track before first rotation.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 55 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Ordering discipline for 51234: the catalogue page quotes 51234 M and its 270/930 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51234-M?",
        "a": "51234 M measures 170 mm bore × 240 mm OD × 55 mm bearing height (6.693 × 9.449 × 2.165 in), mass about 8150 g. SKF 17000 ratings: C 270 kN, C0 930 kN, Pu 24 kN, reference speed 1,200 r/min (thermal) and limiting speed 1,700 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51234 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 34 encode the bore as 170 mm (code 34 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51234-M lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 1,700 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51234",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 170×240×55 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51234",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51234-M",
      "51234 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51334-M",
    "brand": "SKF",
    "manufacturer_designation": "51334 M",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 170,
    "D_mm": 280,
    "B_mm": 87,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 468,
    "static_load_kN": 1760,
    "fatigue_load_limit_kN": 43,
    "reference_speed_rpm": 800,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "weight_g": 22000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51334 M is SKF's 170 mm-bore single-direction thrust ball bearing in the 51300 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 170×280×87 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 34 encode the bore as 170 mm (code 34 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 170×280×87 mm (6.693×11.024×3.425 in), 55.0 mm radial section, C 468 kN, C0 1760 kN, Pu 43 kN. reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical), catalogue mass 22000 g. Envelope economics: the 87 mm axial height over a 55.0 mm radial section yields 5.4 kN of dynamic capacity per height millimetre, and the bearing weighs 22000 g for 468 kN C — about 47 g per rated kN. Stack/annulus proportions: the 87 mm axial stack over the 38,877 mm² washer annulus gives 2.24 mm of height per annular square millimetre ×10⁻³, and at 22000 g the bearing holds about 80.0 kN of C0 per kilogram. Minimum-load arithmetic: with dm ≈ 225.0 mm and factor A 16, Fam ≈ A·(n·dm/1000)² at the 800 r/min reference speed is about 518.4 kN for 51334 M; below that preload the balls skid and smear the tracks. Mass and section check: 22000 g inside the 170×280×87 mm outline leaves a 55.0 mm radial section, and the 1760 kN static rating is 3.76× the dynamic rating — plan static safety and minimum preload against those figures. Light-load floor: Pu = 43 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51334 M; the number is 9 % of the 468 kN dynamic rating. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 22000 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 170 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "offshore and dock winch drums",
      "heavy converter and ladle-tilt pivots"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "track rust staining from condensate during long idle periods in humid plant air",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 468/1760 kN and the available 280 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 170 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "When the housing seat cannot be machined square to the 170 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51300 bearing.",
      "The 468/1760 kN figures belong to 51334 M specifically (the single flat brass execution of 51334); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51334-M?",
        "a": "51334 M measures 170 mm bore × 280 mm OD × 87 mm bearing height (6.693 × 11.024 × 3.425 in), mass about 22000 g. SKF 17000 ratings: C 468 kN, C0 1760 kN, Pu 43 kN, reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51334 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 34 encode the bore as 170 mm (code 34 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51334 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51334-M?",
        "a": "The 800 r/min reference speed is the thermal balance under catalogue load; the 1,100 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51334",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 170×280×87 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51334",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51334-M",
      "51334 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51136-M",
    "brand": "SKF",
    "manufacturer_designation": "51136 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 180,
    "D_mm": 225,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 135,
    "static_load_kN": 570,
    "fatigue_load_limit_kN": 15,
    "reference_speed_rpm": 1500,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 3500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51136 M is an ISO 104 single-direction thrust ball bearing, 180 mm bore and 225 mm OD on a flat housing seat, standing 34 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 36: bore 180 mm (code 36 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 180×225×34 mm (7.087×8.858×1.339 in), 22.5 mm radial section, C 135 kN, C0 570 kN, Pu 15 kN. reference speed 1,500 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 3500 g. Speed-ratio note for this exact unit: the reference speed is 1,500 r/min against a 2,200 r/min limiting speed, a reference-to-limit ratio of 0.68. Load balance: C0 570 kN against C 135 kN gives a 4.22 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 15 kN enters the adjusted-life check. Minimum-load arithmetic: with dm ≈ 202.5 mm and factor A 1.7, Fam ≈ A·(n·dm/1000)² at the 1,500 r/min reference speed is about 156.8 kN for 51136 M; below that preload the balls skid and smear the tracks. Speed band width for this size is 700 r/min between reference and limiting (1.47× ratio); lubrication, preload and heat removal decide where inside that band 51136 M can actually run. Stack/annulus proportions: the 34 mm axial stack over the 14,314 mm² washer annulus gives 2.38 mm of height per annular square millimetre ×10⁻³, and at 3500 g the bearing holds about 162.9 kN of C0 per kilogram. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 3500 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 180 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "marine gearbox thrust positions",
      "very heavy crane and ladle hooks"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51136 against two-way load lifts the loose washer off its raceway.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 135/570 kN and the available 225 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 34 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 135 kN track before first rotation.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51136 M as the single flat brass execution; other order numbers of the 51136 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51136-M?",
        "a": "The catalogue envelope is 180×225×34 mm, mass 3500 g; ratings C 135 kN / C0 570 kN / Pu 15 kN, reference speed 1,500 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51136 M mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 36: bore 180 mm (code 36 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51136-M carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 180 mm shaft must go to a separate radial bearing; mixed loading through 51136 M edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51136",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "51136",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51136-M",
      "51136 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51236-M",
    "brand": "SKF",
    "manufacturer_designation": "51236 M",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 180,
    "D_mm": 250,
    "B_mm": 56,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 302,
    "static_load_kN": 1120,
    "fatigue_load_limit_kN": 28.5,
    "reference_speed_rpm": 1200,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "weight_g": 8600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51236 M is a SKF single-direction thrust ball bearing for a 180 mm seat, built to ISO 104, with a flat housing seating surface, 180×250×56 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 36 decodes to 180 mm (code 36 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 180×250×56 mm (7.087×9.843×2.205 in), 35.0 mm radial section, C 302 kN, C0 1120 kN, Pu 28.5 kN. reference speed 1,200 r/min (thermal) and limiting speed 1,600 r/min (mechanical), catalogue mass 8600 g. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 6.1 at the 1,600 r/min limiting speed raises the required axial preload to about 721.8 kN; the reference-speed value 406.0 kN is the thermal design point. Envelope economics: the 56 mm axial height over a 35.0 mm radial section yields 5.4 kN of dynamic capacity per height millimetre, and the bearing weighs 8600 g for 302 kN C — about 28 g per rated kN. Speed band width for this size is 400 r/min between reference and limiting (1.33× ratio); lubrication, preload and heat removal decide where inside that band 51236 M can actually run. Capacity density: 302 kN C from 8.600 kg of bearing steel gives about 35.1 kN per kilogram; static density is correspondingly 130.2 kN/kg at C0 1120 kN. Track-circle loading: per millimetre of mean track circumference the 302 kN dynamic rating corresponds to roughly 0.45 kN/mm of π·dm track, a useful comparison against the other dimension series of the 180 mm bore. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 8600 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 180 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "very heavy crane and ladle hooks",
      "offshore and dock winch drums",
      "heavy converter and ladle-tilt pivots"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 56 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 302 kN track before first rotation.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 302/1120 kN and the available 250 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51236 against two-way load lifts the loose washer off its raceway.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51236 M as the single flat brass execution; other order numbers of the 51236 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51236-M?",
        "a": "Boundary dimensions to ISO 104: bore 180 mm, OD 250 mm, height 56 mm; weight 8600 g. Load figures from SKF 17000: dynamic 302 kN, static 1120 kN, fatigue limit 28.5 kN; reference speed 1,200 r/min (thermal) and limiting speed 1,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51236 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 36 decodes to 180 mm (code 36 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, M-cage product) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "Can 51236-M carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 180 mm shaft must go to a separate radial bearing; mixed loading through 51236 M edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51236",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 180×250×56 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51236",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51236-M",
      "51236 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51336-M",
    "brand": "SKF",
    "manufacturer_designation": "51336 M",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 180,
    "D_mm": 300,
    "B_mm": 95,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 520,
    "static_load_kN": 2000,
    "fatigue_load_limit_kN": 47.5,
    "reference_speed_rpm": 750,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "weight_g": 28500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51336 M is an ISO 104 single-direction thrust ball bearing, 180 mm bore and 300 mm OD on a flat housing seat, standing 95 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 36: bore 180 mm (code 36 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 180×300×95 mm (7.087×11.811×3.74 in), 60.0 mm radial section, C 520 kN, C0 2000 kN, Pu 47.5 kN. reference speed 750 r/min (thermal) and limiting speed 1,100 r/min (mechanical), catalogue mass 28500 g. Rating split for documentation: dynamic 520 kN (L10 life), static 2000 kN (safety factor s0), fatigue limit 47.5 kN (adjusted life) — three different uses of three different numbers for 51336 M, none interchangeable with another. Light-load floor: Pu = 47.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51336 M; the number is 9 % of the 520 kN dynamic rating. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51336 M covers about 45,239 mm², distributing C0 2000 kN over a mean track circle of π·dm ≈ 754 mm. Speed band width for this size is 350 r/min between reference and limiting (1.47× ratio); lubrication, preload and heat removal decide where inside that band 51336 M can actually run. Sizing arithmetic on the 180 mm bore: 520 kN C over the 60.0 mm radial section gives 8.7 kN per section millimetre, and the 95 mm stack height is 1.58× that section — proportions typical of a 51300 thrust section. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51336 M adds a small amount of mass and cage strength without changing the 180×300×95 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,100 r/min ceiling.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "heavy converter and ladle-tilt pivots",
      "very heavy crane and ladle hooks"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "The 51336 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 180 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 95 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51336 against two-way load lifts the loose washer off its raceway.",
      "The 520/2000 kN figures belong to 51336 M specifically (the single flat brass execution of 51336); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51336-M?",
        "a": "The catalogue envelope is 180×300×95 mm, mass 28500 g; ratings C 520 kN / C0 2000 kN / Pu 47.5 kN, reference speed 750 r/min (thermal) and limiting speed 1,100 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51336 M mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 36: bore 180 mm (code 36 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51336-M lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 1,100 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 180 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51336",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 180×300×95 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51336",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51336-M",
      "51336 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51138-M",
    "brand": "SKF",
    "manufacturer_designation": "51138 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 190,
    "D_mm": 240,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 172,
    "static_load_kN": 710,
    "fatigue_load_limit_kN": 18,
    "reference_speed_rpm": 1400,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "weight_g": 4050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51138 M is a SKF single-direction thrust ball bearing for a 190 mm seat, built to ISO 104, with a flat housing seating surface, 190×240×37 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 38 decodes to 190 mm (code 38 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 190×240×37 mm (7.48×9.449×1.457 in), 25.0 mm radial section, C 172 kN, C0 710 kN, Pu 18 kN. reference speed 1,400 r/min (thermal) and limiting speed 2,000 r/min (mechanical), catalogue mass 4050 g. Mass and section check: 4050 g inside the 190×240×37 mm outline leaves a 25.0 mm radial section, and the 710 kN static rating is 4.13× the dynamic rating — plan static safety and minimum preload against those figures. Pitch-diameter arithmetic: dm = (190+240)/2 = 215.0 mm; at the 2,000 r/min limiting speed that corresponds to roughly 430k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Selection figures for 51138 M: the C0/C ratio is 4.13, Pu 18 kN is about 10 % of C, and the catalogue mass works out to roughly 21 g per millimetre of bore; the printed minimum-load factor is A 2.6. Load balance: C0 710 kN against C 172 kN gives a 4.13 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 18 kN enters the adjusted-life check. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 2.6 at the 2,000 r/min limiting speed raises the required axial preload to about 480.7 kN; the reference-speed value 235.6 kN is the thermal design point. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51138 M adds a small amount of mass and cage strength without changing the 190×240×37 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 2,000 r/min ceiling.",
    "applications": [
      "marine gearbox thrust positions",
      "very heavy crane and ladle hooks",
      "offshore and dock winch drums"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 2.6; for 51138 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "When the housing seat cannot be machined square to the 190 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 172/710 kN and the available 240 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 172/710 kN figures belong to 51138 M specifically (the single flat brass execution of 51138); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51138-M?",
        "a": "Boundary dimensions to ISO 104: bore 190 mm, OD 240 mm, height 37 mm; weight 4050 g. Load figures from SKF 17000: dynamic 172 kN, static 710 kN, fatigue limit 18 kN; reference speed 1,400 r/min (thermal) and limiting speed 2,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51138 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 38 decodes to 190 mm (code 38 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51138-M lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 2,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 190 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51138",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "51138",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51138-M",
      "51138 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51238-M",
    "brand": "SKF",
    "manufacturer_designation": "51238 M",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 190,
    "D_mm": 270,
    "B_mm": 62,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 332,
    "static_load_kN": 1270,
    "fatigue_load_limit_kN": 31,
    "reference_speed_rpm": 1100,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "weight_g": 12000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51238 M is SKF's 190 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 190×270×62 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 38 encode the bore as 190 mm (code 38 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 190×270×62 mm (7.48×10.63×2.441 in), 40.0 mm radial section, C 332 kN, C0 1270 kN, Pu 31 kN. reference speed 1,100 r/min (thermal) and limiting speed 1,600 r/min (mechanical), catalogue mass 12000 g. Stack/annulus proportions: the 62 mm axial stack over the 28,903 mm² washer annulus gives 2.15 mm of height per annular square millimetre ×10⁻³, and at 12000 g the bearing holds about 105.8 kN of C0 per kilogram. Track-circle loading: per millimetre of mean track circumference the 332 kN dynamic rating corresponds to roughly 0.46 kN/mm of π·dm track, a useful comparison against the other dimension series of the 190 mm bore. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 8.4 at the 1,600 r/min limiting speed raises the required axial preload to about 1137.6 kN; the reference-speed value 537.7 kN is the thermal design point. Light-load floor: Pu = 31 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51238 M; the number is 9 % of the 332 kN dynamic rating. At the printed limiting speed of 1,600 r/min the mean pitch diameter dm ≈ 230.0 mm implies a dn value around 368k mm·r/min; the 1,100 r/min reference speed is the thermal-planning value under catalogue load. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 12000 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 190 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "very heavy crane and ladle hooks",
      "heavy converter and ladle-tilt pivots"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 332/1270 kN and the available 270 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51238 against two-way load lifts the loose washer off its raceway.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 332 kN track before first rotation.",
      "Ordering discipline for 51238: the catalogue page quotes 51238 M and its 332/1270 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51238-M?",
        "a": "51238 M measures 190 mm bore × 270 mm OD × 62 mm bearing height (7.48 × 10.63 × 2.441 in), mass about 12000 g. SKF 17000 ratings: C 332 kN, C0 1270 kN, Pu 31 kN, reference speed 1,100 r/min (thermal) and limiting speed 1,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51238 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 38 encode the bore as 190 mm (code 38 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51238-M?",
        "a": "The 1,100 r/min reference speed is the thermal balance under catalogue load; the 1,600 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51238-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 8.4 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51238",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 190×270×62 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51238",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51238-M",
      "51238 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51338-M",
    "brand": "SKF",
    "manufacturer_designation": "51338 M",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 190,
    "D_mm": 320,
    "B_mm": 105,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 559,
    "static_load_kN": 2200,
    "fatigue_load_limit_kN": 51,
    "reference_speed_rpm": 700,
    "limiting_speed_rpm": 950,
    "max_rpm": 950,
    "weight_g": 36500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51300 series order number 51338 M is a SKF single-direction thrust ball bearing for a 190 mm seat, built to ISO 104, with a flat housing seating surface, 190×320×105 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 38 decodes to 190 mm (code 38 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 190×320×105 mm (7.48×12.598×4.134 in), 65.0 mm radial section, C 559 kN, C0 2200 kN, Pu 51 kN. reference speed 700 r/min (thermal) and limiting speed 950 r/min (mechanical), catalogue mass 36500 g. Track-circle loading: per millimetre of mean track circumference the 559 kN dynamic rating corresponds to roughly 0.70 kN/mm of π·dm track, a useful comparison against the other dimension series of the 190 mm bore. Light-load floor: Pu = 51 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51338 M; the number is 9 % of the 559 kN dynamic rating. Stack/annulus proportions: the 105 mm axial stack over the 52,072 mm² washer annulus gives 2.02 mm of height per annular square millimetre ×10⁻³, and at 36500 g the bearing holds about 60.3 kN of C0 per kilogram. Mass and section check: 36500 g inside the 190×320×105 mm outline leaves a 65.0 mm radial section, and the 2200 kN static rating is 3.94× the dynamic rating — plan static safety and minimum preload against those figures. Capacity density: 559 kN C from 36.500 kg of bearing steel gives about 15.3 kN per kilogram; static density is correspondingly 60.3 kN/kg at C0 2200 kN. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 36500 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 190 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "very heavy crane and ladle hooks",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 30; for 51338 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 51338 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 190 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 559/2200 kN and the available 320 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 190 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Ordering discipline for 51338: the catalogue page quotes 51338 M and its 559/2200 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51338-M?",
        "a": "Boundary dimensions to ISO 104: bore 190 mm, OD 320 mm, height 105 mm; weight 36500 g. Load figures from SKF 17000: dynamic 559 kN, static 2200 kN, fatigue limit 51 kN; reference speed 700 r/min (thermal) and limiting speed 950 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51338 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 38 decodes to 190 mm (code 38 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51338-M carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 190 mm shaft must go to a separate radial bearing; mixed loading through 51338 M edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51338",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 190×320×105 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51338",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51338-M",
      "51338 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51140-M",
    "brand": "SKF",
    "manufacturer_designation": "51140 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 200,
    "D_mm": 250,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 168,
    "static_load_kN": 710,
    "fatigue_load_limit_kN": 17.6,
    "reference_speed_rpm": 1400,
    "limiting_speed_rpm": 1900,
    "max_rpm": 1900,
    "weight_g": 4250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51140 M is an ISO 104 single-direction thrust ball bearing, 200 mm bore and 250 mm OD on a flat housing seat, standing 37 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 40: bore 200 mm (code 40 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 200×250×37 mm (7.874×9.843×1.457 in), 25.0 mm radial section, C 168 kN, C0 710 kN, Pu 17.6 kN. reference speed 1,400 r/min (thermal) and limiting speed 1,900 r/min (mechanical), catalogue mass 4250 g. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 2.6 at the 1,900 r/min limiting speed raises the required axial preload to about 475.2 kN; the reference-speed value 258.0 kN is the thermal design point. Static-first selection data: 710 kN C0 spread across the 37 mm stack gives 19.2 kN of static rating per height millimetre, and the 4250 g mass/C0 ratio is about 6 g per static kN — crane-hook and screw positions are normally sized on these two figures. Sizing arithmetic on the 200 mm bore: 168 kN C over the 25.0 mm radial section gives 6.7 kN per section millimetre, and the 37 mm stack height is 1.48× that section — proportions typical of a 51100 thrust section. Rating split for documentation: dynamic 168 kN (L10 life), static 710 kN (safety factor s0), fatigue limit 17.6 kN (adjusted life) — three different uses of three different numbers for 51140 M, none interchangeable with another. Selection figures for 51140 M: the C0/C ratio is 4.23, Pu 17.6 kN is about 10 % of C, and the catalogue mass works out to roughly 21 g per millimetre of bore; the printed minimum-load factor is A 2.6. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 4250 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 200 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "heavy converter and ladle-tilt pivots",
      "very heavy crane and ladle hooks",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "track rust staining from condensate during long idle periods in humid plant air"
    ],
    "pitfalls": [
      "When the housing seat cannot be machined square to the 200 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 168/710 kN and the available 250 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 37 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51140 against two-way load lifts the loose washer off its raceway.",
      "Ordering discipline for 51140: the catalogue page quotes 51140 M and its 168/710 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51140-M?",
        "a": "The catalogue envelope is 200×250×37 mm, mass 4250 g; ratings C 168 kN / C0 710 kN / Pu 17.6 kN, reference speed 1,400 r/min (thermal) and limiting speed 1,900 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51140 M mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 40: bore 200 mm (code 40 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 200 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51140 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51140",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "51140",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51140-M",
      "51140 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51240-M",
    "brand": "SKF",
    "manufacturer_designation": "51240 M",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 200,
    "D_mm": 280,
    "B_mm": 62,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 338,
    "static_load_kN": 1320,
    "fatigue_load_limit_kN": 31.5,
    "reference_speed_rpm": 1100,
    "limiting_speed_rpm": 1500,
    "max_rpm": 1500,
    "weight_g": 12000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51240 M is a SKF single-direction thrust ball bearing for a 200 mm seat, built to ISO 104, with a flat housing seating surface, 200×280×62 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 40 decodes to 200 mm (code 40 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 200×280×62 mm (7.874×11.024×2.441 in), 40.0 mm radial section, C 338 kN, C0 1320 kN, Pu 31.5 kN. reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical), catalogue mass 12000 g. Rating split for documentation: dynamic 338 kN (L10 life), static 1320 kN (safety factor s0), fatigue limit 31.5 kN (adjusted life) — three different uses of three different numbers for 51240 M, none interchangeable with another. Sizing arithmetic on the 200 mm bore: 338 kN C over the 40.0 mm radial section gives 8.4 kN per section millimetre, and the 62 mm stack height is 1.55× that section — proportions typical of a 51200 thrust section. Bore-to-OD planning: OD 280 over bore 200 is a 1.40× step for this size, and the 62 mm height gives a bore/height ratio of 3.23; use these ratios when the housing recess around the 200 mm shaft is the first constraint. Speed band width for this size is 400 r/min between reference and limiting (1.36× ratio); lubrication, preload and heat removal decide where inside that band 51240 M can actually run. Envelope economics: the 62 mm axial height over a 40.0 mm radial section yields 5.5 kN of dynamic capacity per height millimetre, and the bearing weighs 12000 g for 338 kN C — about 36 g per rated kN. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51240 M adds a small amount of mass and cage strength without changing the 200×280×62 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,500 r/min ceiling.",
    "applications": [
      "heavy converter and ladle-tilt pivots",
      "large press rams and screwdown mechanisms",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51240 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 200 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 62 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The 338/1320 kN figures belong to 51240 M specifically (the single flat brass execution of 51240); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51240-M?",
        "a": "Boundary dimensions to ISO 104: bore 200 mm, OD 280 mm, height 62 mm; weight 12000 g. Load figures from SKF 17000: dynamic 338 kN, static 1320 kN, fatigue limit 31.5 kN; reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51240 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 40 decodes to 200 mm (code 40 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51240-M carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 200 mm shaft must go to a separate radial bearing; mixed loading through 51240 M edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51240",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 200×280×62 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51240",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51240-M",
      "51240 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51340-M",
    "brand": "SKF",
    "manufacturer_designation": "51340 M",
    "series": "51300-series",
    "type": "thrust_ball",
    "d_mm": 200,
    "D_mm": 340,
    "B_mm": 110,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 624,
    "static_load_kN": 2600,
    "fatigue_load_limit_kN": 58.5,
    "reference_speed_rpm": 630,
    "limiting_speed_rpm": 900,
    "max_rpm": 900,
    "weight_g": 44500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51340 M is an ISO 104 single-direction thrust ball bearing, 200 mm bore and 340 mm OD on a flat housing seat, standing 110 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 40: bore 200 mm (code 40 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 200×340×110 mm (7.874×13.386×4.331 in), 70.0 mm radial section, C 624 kN, C0 2600 kN, Pu 58.5 kN. reference speed 630 r/min (thermal) and limiting speed 900 r/min (mechanical), catalogue mass 44500 g. Stack/annulus proportions: the 110 mm axial stack over the 59,376 mm² washer annulus gives 1.85 mm of height per annular square millimetre ×10⁻³, and at 44500 g the bearing holds about 58.4 kN of C0 per kilogram. Envelope economics: the 110 mm axial height over a 70.0 mm radial section yields 5.7 kN of dynamic capacity per height millimetre, and the bearing weighs 44500 g for 624 kN C — about 71 g per rated kN. Pitch-diameter arithmetic: dm = (200+340)/2 = 270.0 mm; at the 900 r/min limiting speed that corresponds to roughly 243k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Speed band width for this size is 270 r/min between reference and limiting (1.43× ratio); lubrication, preload and heat removal decide where inside that band 51340 M can actually run. Speed-ratio note for this exact unit: the reference speed is 630 r/min against a 900 r/min limiting speed, a reference-to-limit ratio of 0.70. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 44500 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 200 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "marine gearbox thrust positions",
      "large press rams and screwdown mechanisms",
      "heavy converter and ladle-tilt pivots"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 624/2600 kN and the available 340 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 200 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51340 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 200 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51300 bearing.",
      "Ordering discipline for 51340: the catalogue page quotes 51340 M and its 624/2600 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51340-M?",
        "a": "The catalogue envelope is 200×340×110 mm, mass 44500 g; ratings C 624 kN / C0 2600 kN / Pu 58.5 kN, reference speed 630 r/min (thermal) and limiting speed 900 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51340 M mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 40: bore 200 mm (code 40 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51340-M?",
        "a": "The 630 r/min reference speed is the thermal balance under catalogue load; the 900 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51340-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 35 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51340",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 200×340×110 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51340",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51340-M",
      "51340 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51144-M",
    "brand": "SKF",
    "manufacturer_designation": "51144 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 220,
    "D_mm": 270,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 178,
    "static_load_kN": 800,
    "fatigue_load_limit_kN": 19,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1900,
    "max_rpm": 1900,
    "weight_g": 4600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51144 M is SKF's 220 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 220×270×37 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 44 encode the bore as 220 mm (code 44 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 220×270×37 mm (8.661×10.63×1.457 in), 25.0 mm radial section, C 178 kN, C0 800 kN, Pu 19 kN. reference speed 1,300 r/min (thermal) and limiting speed 1,900 r/min (mechanical), catalogue mass 4600 g. Mass and section check: 4600 g inside the 220×270×37 mm outline leaves a 25.0 mm radial section, and the 800 kN static rating is 4.49× the dynamic rating — plan static safety and minimum preload against those figures. Static-first selection data: 800 kN C0 spread across the 37 mm stack gives 21.6 kN of static rating per height millimetre, and the 4600 g mass/C0 ratio is about 6 g per static kN — crane-hook and screw positions are normally sized on these two figures. Capacity density: 178 kN C from 4.600 kg of bearing steel gives about 38.7 kN per kilogram; static density is correspondingly 173.9 kN/kg at C0 800 kN. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51144 M covers about 19,242 mm², distributing C0 800 kN over a mean track circle of π·dm ≈ 770 mm. Sizing arithmetic on the 220 mm bore: 178 kN C over the 25.0 mm radial section gives 7.1 kN per section millimetre, and the 37 mm stack height is 1.48× that section — proportions typical of a 51100 thrust section. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 4600 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 220 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "very heavy crane and ladle hooks",
      "marine gearbox thrust positions",
      "offshore and dock winch drums"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "false brinelling of the stationary tracks while the machine stands under vibration"
    ],
    "pitfalls": [
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 220 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 3.3; for 51144 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "When the housing seat cannot be machined square to the 220 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 37 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The 178/800 kN figures belong to 51144 M specifically (the single flat brass execution of 51144); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51144-M?",
        "a": "51144 M measures 220 mm bore × 270 mm OD × 37 mm bearing height (8.661 × 10.63 × 1.457 in), mass about 4600 g. SKF 17000 ratings: C 178 kN, C0 800 kN, Pu 19 kN, reference speed 1,300 r/min (thermal) and limiting speed 1,900 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51144 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 44 encode the bore as 220 mm (code 44 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, M-cage product) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "Can 51144-M carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 220 mm shaft must go to a separate radial bearing; mixed loading through 51144 M edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51144",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "51144",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51144-M",
      "51144 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51244-M",
    "brand": "SKF",
    "manufacturer_designation": "51244 M",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 220,
    "D_mm": 300,
    "B_mm": 63,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 358,
    "static_load_kN": 1460,
    "fatigue_load_limit_kN": 33.5,
    "reference_speed_rpm": 950,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "weight_g": 13000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51244 M is SKF's 220 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 220×300×63 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 44 encode the bore as 220 mm (code 44 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 220×300×63 mm (8.661×11.811×2.48 in), 40.0 mm radial section, C 358 kN, C0 1460 kN, Pu 33.5 kN. reference speed 950 r/min (thermal) and limiting speed 1,300 r/min (mechanical), catalogue mass 13000 g. Load balance: C0 1460 kN against C 358 kN gives a 4.08 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 33.5 kN enters the adjusted-life check. Speed band width for this size is 350 r/min between reference and limiting (1.37× ratio); lubrication, preload and heat removal decide where inside that band 51244 M can actually run. Track-circle loading: per millimetre of mean track circumference the 358 kN dynamic rating corresponds to roughly 0.44 kN/mm of π·dm track, a useful comparison against the other dimension series of the 220 mm bore. Stack/annulus proportions: the 63 mm axial stack over the 32,673 mm² washer annulus gives 1.93 mm of height per annular square millimetre ×10⁻³, and at 13000 g the bearing holds about 112.3 kN of C0 per kilogram. Mass and section check: 13000 g inside the 220×300×63 mm outline leaves a 40.0 mm radial section, and the 1460 kN static rating is 4.08× the dynamic rating — plan static safety and minimum preload against those figures. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51244 M adds a small amount of mass and cage strength without changing the 220×300×63 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,300 r/min ceiling.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "very heavy crane and ladle hooks",
      "offshore and dock winch drums"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 220 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 358 kN track before first rotation.",
      "When the housing seat cannot be machined square to the 220 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 63 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The 358/1460 kN figures belong to 51244 M specifically (the single flat brass execution of 51244); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51244-M?",
        "a": "51244 M measures 220 mm bore × 300 mm OD × 63 mm bearing height (8.661 × 11.811 × 2.48 in), mass about 13000 g. SKF 17000 ratings: C 358 kN, C0 1460 kN, Pu 33.5 kN, reference speed 950 r/min (thermal) and limiting speed 1,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51244 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 44 encode the bore as 220 mm (code 44 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can a single 51244 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      },
      {
        "q": "What do the two published speeds mean for 51244-M?",
        "a": "The 950 r/min reference speed is the thermal balance under catalogue load; the 1,300 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51244",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 220×300×63 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51244",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51244-M",
      "51244 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51148-M",
    "brand": "SKF",
    "manufacturer_designation": "51148 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 240,
    "D_mm": 300,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 234,
    "static_load_kN": 1040,
    "fatigue_load_limit_kN": 23.6,
    "reference_speed_rpm": 1100,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "weight_g": 7550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51148 M is SKF's 240 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 240×300×45 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 48 encode the bore as 240 mm (code 48 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 240×300×45 mm (9.449×11.811×1.772 in), 30.0 mm radial section, C 234 kN, C0 1040 kN, Pu 23.6 kN. reference speed 1,100 r/min (thermal) and limiting speed 1,600 r/min (mechanical), catalogue mass 7550 g. Imperial cross-check for procurement drawings: 9.449 in bore, 11.811 in OD, 1.772 in height, and the 7550 g catalogue mass converts to 7.550 kg (266.3 oz). Washer-annulus check: the π/4·(D²−d²) contact annulus of 51148 M covers about 25,447 mm², distributing C0 1040 kN over a mean track circle of π·dm ≈ 848 mm. Speed planning separates the two ceilings mechanically: the pressed brass cage and balls tolerate 1,600 r/min while thermal balance under catalogue load sets the 1,100 r/min reference; at dm ≈ 270.0 mm the corresponding dn is approximately 432k mm·r/min. Speed band width for this size is 500 r/min between reference and limiting (1.45× ratio); lubrication, preload and heat removal decide where inside that band 51148 M can actually run. Static-first selection data: 1040 kN C0 spread across the 45 mm stack gives 23.1 kN of static rating per height millimetre, and the 7550 g mass/C0 ratio is about 7 g per static kN — crane-hook and screw positions are normally sized on these two figures. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51148 M adds a small amount of mass and cage strength without changing the 240×300×45 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,600 r/min ceiling.",
    "applications": [
      "heavy converter and ladle-tilt pivots",
      "marine gearbox thrust positions",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 5.6; for 51148 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 51148 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 240 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 240 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Ordering discipline for 51148: the catalogue page quotes 51148 M and its 234/1040 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51148-M?",
        "a": "51148 M measures 240 mm bore × 300 mm OD × 45 mm bearing height (9.449 × 11.811 × 1.772 in), mass about 7550 g. SKF 17000 ratings: C 234 kN, C0 1040 kN, Pu 23.6 kN, reference speed 1,100 r/min (thermal) and limiting speed 1,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51148 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 48 encode the bore as 240 mm (code 48 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 240 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51148 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51148",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 240×300×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51148",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51148-M",
      "51148 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51248-M",
    "brand": "SKF",
    "manufacturer_designation": "51248 M",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 240,
    "D_mm": 340,
    "B_mm": 78,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 449,
    "static_load_kN": 1960,
    "fatigue_load_limit_kN": 42.5,
    "reference_speed_rpm": 800,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "weight_g": 23000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51248 M is an ISO 104 single-direction thrust ball bearing, 240 mm bore and 340 mm OD on a flat housing seat, standing 78 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 48: bore 240 mm (code 48 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 240×340×78 mm (9.449×13.386×3.071 in), 50.0 mm radial section, C 449 kN, C0 1960 kN, Pu 42.5 kN. reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical), catalogue mass 23000 g. Stack/annulus proportions: the 78 mm axial stack over the 45,553 mm² washer annulus gives 1.71 mm of height per annular square millimetre ×10⁻³, and at 23000 g the bearing holds about 85.2 kN of C0 per kilogram. Imperial cross-check for procurement drawings: 9.449 in bore, 13.386 in OD, 3.071 in height, and the 23000 g catalogue mass converts to 23.000 kg (811.3 oz). Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 21 at the 1,100 r/min limiting speed raises the required axial preload to about 2137.0 kN; the reference-speed value 1130.3 kN is the thermal design point. Speed band width for this size is 300 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 51248 M can actually run. Envelope economics: the 78 mm axial height over a 50.0 mm radial section yields 5.8 kN of dynamic capacity per height millimetre, and the bearing weighs 23000 g for 449 kN C — about 51 g per rated kN. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51248 M adds a small amount of mass and cage strength without changing the 240×340×78 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,100 r/min ceiling.",
    "applications": [
      "very heavy crane and ladle hooks",
      "large press rams and screwdown mechanisms",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 78 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 449 kN track before first rotation.",
      "The 51248 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 240 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51248 against two-way load lifts the loose washer off its raceway.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51248 M as the single flat brass execution; other order numbers of the 51248 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51248-M?",
        "a": "The catalogue envelope is 240×340×78 mm, mass 23000 g; ratings C 449 kN / C0 1960 kN / Pu 42.5 kN, reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51248 M mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 48: bore 240 mm (code 48 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Can 51248-M carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 240 mm shaft must go to a separate radial bearing; mixed loading through 51248 M edge-loads the balls and destroys the washers."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51248",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 240×340×78 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51248",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51248-M",
      "51248 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51152-M",
    "brand": "SKF",
    "manufacturer_designation": "51152 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 260,
    "D_mm": 320,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 238,
    "static_load_kN": 1100,
    "fatigue_load_limit_kN": 24,
    "reference_speed_rpm": 1100,
    "limiting_speed_rpm": 1500,
    "max_rpm": 1500,
    "weight_g": 8100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51152 M is an ISO 104 single-direction thrust ball bearing, 260 mm bore and 320 mm OD on a flat housing seat, standing 45 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 52: bore 260 mm (code 52 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 260×320×45 mm (10.236×12.598×1.772 in), 30.0 mm radial section, C 238 kN, C0 1100 kN, Pu 24 kN. reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical), catalogue mass 8100 g. At the printed limiting speed of 1,500 r/min the mean pitch diameter dm ≈ 290.0 mm implies a dn value around 435k mm·r/min; the 1,100 r/min reference speed is the thermal-planning value under catalogue load. Rating split for documentation: dynamic 238 kN (L10 life), static 1100 kN (safety factor s0), fatigue limit 24 kN (adjusted life) — three different uses of three different numbers for 51152 M, none interchangeable with another. Sizing arithmetic on the 260 mm bore: 238 kN C over the 30.0 mm radial section gives 7.9 kN per section millimetre, and the 45 mm stack height is 1.50× that section — proportions typical of a 51100 thrust section. Load balance: C0 1100 kN against C 238 kN gives a 4.62 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 24 kN enters the adjusted-life check. Selection figures for 51152 M: the C0/C ratio is 4.62, Pu 24 kN is about 10 % of C, and the catalogue mass works out to roughly 31 g per millimetre of bore; the printed minimum-load factor is A 6.3. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 8100 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 260 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "very heavy crane and ladle hooks",
      "marine gearbox thrust positions",
      "heavy converter and ladle-tilt pivots"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "The 51152 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 260 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 6.3; for 51152 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 260 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 238 kN track before first rotation.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51152 M as the single flat brass execution; other order numbers of the 51152 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51152-M?",
        "a": "The catalogue envelope is 260×320×45 mm, mass 8100 g; ratings C 238 kN / C0 1100 kN / Pu 24 kN, reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51152 M mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 52: bore 260 mm (code 52 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51152-M lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 1,500 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 260 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51152",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 260×320×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51152",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51152-M",
      "51152 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51252-M",
    "brand": "SKF",
    "manufacturer_designation": "51252 M",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 260,
    "D_mm": 360,
    "B_mm": 79,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 488,
    "static_load_kN": 2240,
    "fatigue_load_limit_kN": 46.5,
    "reference_speed_rpm": 750,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "weight_g": 25000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51252 M is an ISO 104 single-direction thrust ball bearing, 260 mm bore and 360 mm OD on a flat housing seat, standing 79 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 52: bore 260 mm (code 52 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 260×360×79 mm (10.236×14.173×3.11 in), 50.0 mm radial section, C 488 kN, C0 2240 kN, Pu 46.5 kN. reference speed 750 r/min (thermal) and limiting speed 1,100 r/min (mechanical), catalogue mass 25000 g. Pitch-diameter arithmetic: dm = (260+360)/2 = 310.0 mm; at the 1,100 r/min limiting speed that corresponds to roughly 341k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Speed-ratio note for this exact unit: the reference speed is 750 r/min against a 1,100 r/min limiting speed, a reference-to-limit ratio of 0.68. Sizing arithmetic on the 260 mm bore: 488 kN C over the 50.0 mm radial section gives 9.8 kN per section millimetre, and the 79 mm stack height is 1.58× that section — proportions typical of a 51200 thrust section. Light-load floor: Pu = 46.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51252 M; the number is 10 % of the 488 kN dynamic rating. Speed planning separates the two ceilings mechanically: the pressed brass cage and balls tolerate 1,100 r/min while thermal balance under catalogue load sets the 750 r/min reference; at dm ≈ 310.0 mm the corresponding dn is approximately 341k mm·r/min. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 25000 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 260 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "very heavy crane and ladle hooks",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 24; for 51252 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 488/2240 kN and the available 360 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 51252 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 260 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 79 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Ordering discipline for 51252: the catalogue page quotes 51252 M and its 488/2240 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51252-M?",
        "a": "The catalogue envelope is 260×360×79 mm, mass 25000 g; ratings C 488 kN / C0 2240 kN / Pu 46.5 kN, reference speed 750 r/min (thermal) and limiting speed 1,100 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51252 M mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 52: bore 260 mm (code 52 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51252-M lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 1,100 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51252",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 260×360×79 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51252",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51252-M",
      "51252 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51156-M",
    "brand": "SKF",
    "manufacturer_designation": "51156 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 280,
    "D_mm": 350,
    "B_mm": 53,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 319,
    "static_load_kN": 1460,
    "fatigue_load_limit_kN": 30.5,
    "reference_speed_rpm": 950,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "weight_g": 12000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51156 M is an ISO 104 single-direction thrust ball bearing, 280 mm bore and 350 mm OD on a flat housing seat, standing 53 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 56: bore 280 mm (code 56 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 280×350×53 mm (11.024×13.78×2.087 in), 35.0 mm radial section, C 319 kN, C0 1460 kN, Pu 30.5 kN. reference speed 950 r/min (thermal) and limiting speed 1,300 r/min (mechanical), catalogue mass 12000 g. Pitch-diameter arithmetic: dm = (280+350)/2 = 315.0 mm; at the 1,300 r/min limiting speed that corresponds to roughly 410k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Stack/annulus proportions: the 53 mm axial stack over the 34,636 mm² washer annulus gives 1.53 mm of height per annular square millimetre ×10⁻³, and at 12000 g the bearing holds about 121.7 kN of C0 per kilogram. Section proportions: the 35.0 mm radial section compares with 280 mm of bore (section/bore ≈ 0.13) and the 53 mm height is 1.51× that section — the proportions that identify the 51100 envelope at a glance. Light-load floor: Pu = 30.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51156 M; the number is 10 % of the 319 kN dynamic rating. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 11 at the 1,300 r/min limiting speed raises the required axial preload to about 1844.6 kN; the reference-speed value 985.1 kN is the thermal design point. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51156 M adds a small amount of mass and cage strength without changing the 280×350×53 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,300 r/min ceiling.",
    "applications": [
      "heavy converter and ladle-tilt pivots",
      "offshore and dock winch drums",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "track rust staining from condensate during long idle periods in humid plant air",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 319 kN track before first rotation.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 11; for 51156 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51156 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 280 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "The 319/1460 kN figures belong to 51156 M specifically (the single flat brass execution of 51156); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51156-M?",
        "a": "The catalogue envelope is 280×350×53 mm, mass 12000 g; ratings C 319 kN / C0 1460 kN / Pu 30.5 kN, reference speed 950 r/min (thermal) and limiting speed 1,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51156 M mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 56: bore 280 mm (code 56 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51156-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 11 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, M-cage product) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51156",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 280×350×53 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51156",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51156-M",
      "51156 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51256-M",
    "brand": "SKF",
    "manufacturer_designation": "51256 M",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 280,
    "D_mm": 380,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 488,
    "static_load_kN": 2320,
    "fatigue_load_limit_kN": 47.5,
    "reference_speed_rpm": 750,
    "limiting_speed_rpm": 1000,
    "max_rpm": 1000,
    "weight_g": 26500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51256 M is SKF's 280 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 280×380×80 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 56 encode the bore as 280 mm (code 56 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 280×380×80 mm (11.024×14.961×3.15 in), 50.0 mm radial section, C 488 kN, C0 2320 kN, Pu 47.5 kN. reference speed 750 r/min (thermal) and limiting speed 1,000 r/min (mechanical), catalogue mass 26500 g. Speed-ratio note for this exact unit: the reference speed is 750 r/min against a 1,000 r/min limiting speed, a reference-to-limit ratio of 0.75. Imperial cross-check for procurement drawings: 11.024 in bore, 14.961 in OD, 3.15 in height, and the 26500 g catalogue mass converts to 26.500 kg (934.7 oz). Rating split for documentation: dynamic 488 kN (L10 life), static 2320 kN (safety factor s0), fatigue limit 47.5 kN (adjusted life) — three different uses of three different numbers for 51256 M, none interchangeable with another. Speed planning separates the two ceilings mechanically: the pressed brass cage and balls tolerate 1,000 r/min while thermal balance under catalogue load sets the 750 r/min reference; at dm ≈ 330.0 mm the corresponding dn is approximately 330k mm·r/min. Capacity density: 488 kN C from 26.500 kg of bearing steel gives about 18.4 kN per kilogram; static density is correspondingly 87.5 kN/kg at C0 2320 kN. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51256 M adds a small amount of mass and cage strength without changing the 280×380×80 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,000 r/min ceiling.",
    "applications": [
      "heavy converter and ladle-tilt pivots",
      "very heavy crane and ladle hooks",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 488/2320 kN and the available 380 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 28; for 51256 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 280 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 80 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Ordering discipline for 51256: the catalogue page quotes 51256 M and its 488/2320 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51256-M?",
        "a": "51256 M measures 280 mm bore × 380 mm OD × 80 mm bearing height (11.024 × 14.961 × 3.15 in), mass about 26500 g. SKF 17000 ratings: C 488 kN, C0 2320 kN, Pu 47.5 kN, reference speed 750 r/min (thermal) and limiting speed 1,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51256 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 56 encode the bore as 280 mm (code 56 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51256-M?",
        "a": "The 750 r/min reference speed is the thermal balance under catalogue load; the 1,000 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51256-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 28 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51256",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 280×380×80 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51256",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51256-M",
      "51256 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51160-M",
    "brand": "SKF",
    "manufacturer_designation": "51160 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 300,
    "D_mm": 380,
    "B_mm": 62,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 364,
    "static_load_kN": 1760,
    "fatigue_load_limit_kN": 35.5,
    "reference_speed_rpm": 850,
    "limiting_speed_rpm": 1200,
    "max_rpm": 1200,
    "weight_g": 17500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51160 M is an ISO 104 single-direction thrust ball bearing, 300 mm bore and 380 mm OD on a flat housing seat, standing 62 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 60: bore 300 mm (code 60 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 300×380×62 mm (11.811×14.961×2.441 in), 40.0 mm radial section, C 364 kN, C0 1760 kN, Pu 35.5 kN. reference speed 850 r/min (thermal) and limiting speed 1,200 r/min (mechanical), catalogue mass 17500 g. Bore-to-OD planning: OD 380 over bore 300 is a 1.27× step for this size, and the 62 mm height gives a bore/height ratio of 4.84; use these ratios when the housing recess around the 300 mm shaft is the first constraint. Envelope economics: the 62 mm axial height over a 40.0 mm radial section yields 5.9 kN of dynamic capacity per height millimetre, and the bearing weighs 17500 g for 364 kN C — about 48 g per rated kN. Section proportions: the 40.0 mm radial section compares with 300 mm of bore (section/bore ≈ 0.13) and the 62 mm height is 1.55× that section — the proportions that identify the 51100 envelope at a glance. Speed band width for this size is 350 r/min between reference and limiting (1.41× ratio); lubrication, preload and heat removal decide where inside that band 51160 M can actually run. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51160 M covers about 42,726 mm², distributing C0 1760 kN over a mean track circle of π·dm ≈ 1,068 mm. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. The M cage of 51160 M adds a small amount of mass and cage strength without changing the 300×380×62 mm ISO 104 envelope, so the pressed-cage execution drops into the same recess but should not be assumed equal under the 1,200 r/min ceiling.",
    "applications": [
      "very heavy crane and ladle hooks",
      "offshore and dock winch drums",
      "heavy converter and ladle-tilt pivots"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "washer face scoring from swarf trapped between the loose housing washer and its register"
    ],
    "pitfalls": [
      "The 51160 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 300 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "When the housing seat cannot be machined square to the 300 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 62 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 364 kN track before first rotation.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51160 M as the single flat brass execution; other order numbers of the 51160 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51160-M?",
        "a": "The catalogue envelope is 300×380×62 mm, mass 17500 g; ratings C 364 kN / C0 1760 kN / Pu 35.5 kN, reference speed 850 r/min (thermal) and limiting speed 1,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51160 M mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 60: bore 300 mm (code 60 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51160-M?",
        "a": "The 850 r/min reference speed is the thermal balance under catalogue load; the 1,200 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51160-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 16 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51160",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 300×380×62 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51160",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51160-M",
      "51160 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51260-M",
    "brand": "SKF",
    "manufacturer_designation": "51260 M",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 300,
    "D_mm": 420,
    "B_mm": 95,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 585,
    "static_load_kN": 3000,
    "fatigue_load_limit_kN": 57,
    "reference_speed_rpm": 630,
    "limiting_speed_rpm": 850,
    "max_rpm": 850,
    "weight_g": 42000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51260 M is a SKF single-direction thrust ball bearing for a 300 mm seat, built to ISO 104, with a flat housing seating surface, 300×420×95 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 60 decodes to 300 mm (code 60 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 300×420×95 mm (11.811×16.535×3.74 in), 60.0 mm radial section, C 585 kN, C0 3000 kN, Pu 57 kN. reference speed 630 r/min (thermal) and limiting speed 850 r/min (mechanical), catalogue mass 42000 g. Envelope economics: the 95 mm axial height over a 60.0 mm radial section yields 6.2 kN of dynamic capacity per height millimetre, and the bearing weighs 42000 g for 585 kN C — about 72 g per rated kN. Minimum-load arithmetic: with dm ≈ 360.0 mm and factor A 47, Fam ≈ A·(n·dm/1000)² at the 630 r/min reference speed is about 2417.6 kN for 51260 M; below that preload the balls skid and smear the tracks. Sizing arithmetic on the 300 mm bore: 585 kN C over the 60.0 mm radial section gives 9.8 kN per section millimetre, and the 95 mm stack height is 1.58× that section — proportions typical of a 51200 thrust section. Load balance: C0 3000 kN against C 585 kN gives a 5.13 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 57 kN enters the adjusted-life check. Mass and section check: 42000 g inside the 300×420×95 mm outline leaves a 60.0 mm radial section, and the 3000 kN static rating is 5.13× the dynamic rating — plan static safety and minimum preload against those figures. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 42000 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 300 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "heavy converter and ladle-tilt pivots",
      "very heavy crane and ladle hooks",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51260 against two-way load lifts the loose washer off its raceway.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 95 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 47; for 51260 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "When the housing seat cannot be machined square to the 300 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51200 bearing.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51260 M as the single flat brass execution; other order numbers of the 51260 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51260-M?",
        "a": "Boundary dimensions to ISO 104: bore 300 mm, OD 420 mm, height 95 mm; weight 42000 g. Load figures from SKF 17000: dynamic 585 kN, static 3000 kN, fatigue limit 57 kN; reference speed 630 r/min (thermal) and limiting speed 850 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51260 M mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 60 decodes to 300 mm (code 60 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51260-M lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 850 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 300 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51260",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 300×420×95 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51260",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51260-M",
      "51260 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51164-M",
    "brand": "SKF",
    "manufacturer_designation": "51164 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 320,
    "D_mm": 400,
    "B_mm": 63,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 371,
    "static_load_kN": 1860,
    "fatigue_load_limit_kN": 36.5,
    "reference_speed_rpm": 800,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "weight_g": 19000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51164 M is SKF's 320 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 320×400×63 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 64 encode the bore as 320 mm (code 64 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 320×400×63 mm (12.598×15.748×2.48 in), 40.0 mm radial section, C 371 kN, C0 1860 kN, Pu 36.5 kN. reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical), catalogue mass 19000 g. Speed band width for this size is 300 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 51164 M can actually run. Imperial cross-check for procurement drawings: 12.598 in bore, 15.748 in OD, 2.48 in height, and the 19000 g catalogue mass converts to 19.000 kg (670.2 oz). Minimum-load arithmetic: with dm ≈ 360.0 mm and factor A 18, Fam ≈ A·(n·dm/1000)² at the 800 r/min reference speed is about 1493.0 kN for 51164 M; below that preload the balls skid and smear the tracks. Load balance: C0 1860 kN against C 371 kN gives a 5.01 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 36.5 kN enters the adjusted-life check. At the printed limiting speed of 1,100 r/min the mean pitch diameter dm ≈ 360.0 mm implies a dn value around 396k mm·r/min; the 800 r/min reference speed is the thermal-planning value under catalogue load. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 19000 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 320 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "offshore and dock winch drums",
      "heavy converter and ladle-tilt pivots",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 63 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 371/1860 kN and the available 400 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 320 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51164 M as the single flat brass execution; other order numbers of the 51164 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51164-M?",
        "a": "51164 M measures 320 mm bore × 400 mm OD × 63 mm bearing height (12.598 × 15.748 × 2.48 in), mass about 19000 g. SKF 17000 ratings: C 371 kN, C0 1860 kN, Pu 36.5 kN, reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51164 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 64 encode the bore as 320 mm (code 64 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51164-M lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 1,100 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51164",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 320×400×63 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51164",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51164-M",
      "51164 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51264-F",
    "brand": "SKF",
    "manufacturer_designation": "51264 F",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 320,
    "D_mm": 440,
    "B_mm": 95,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel",
    "dynamic_load_kN": 572,
    "static_load_kN": 3000,
    "fatigue_load_limit_kN": 56,
    "reference_speed_rpm": 600,
    "limiting_speed_rpm": 800,
    "max_rpm": 800,
    "weight_g": 45500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51264 F is SKF's 320 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 320×440×95 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 64 encode the bore as 320 mm (code 64 × 5), the standard SKF bore-code rule shared with radial bearings. suffix F identifies a machined steel cage, ball-centred: fitted to the largest sizes of the assortment where the ball complement and centrifugal forces exceed what the stamped sheet-steel execution can guide. Envelope 320×440×95 mm (12.598×17.323×3.74 in), 60.0 mm radial section, C 572 kN, C0 3000 kN, Pu 56 kN. reference speed 600 r/min (thermal) and limiting speed 800 r/min (mechanical), catalogue mass 45500 g. Load balance: C0 3000 kN against C 572 kN gives a 5.24 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 56 kN enters the adjusted-life check. At the printed limiting speed of 800 r/min the mean pitch diameter dm ≈ 380.0 mm implies a dn value around 304k mm·r/min; the 600 r/min reference speed is the thermal-planning value under catalogue load. Light-load floor: Pu = 56 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51264 F; the number is 10 % of the 572 kN dynamic rating. Pitch-diameter arithmetic: dm = (320+440)/2 = 380.0 mm; at the 800 r/min limiting speed that corresponds to roughly 304k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Speed planning separates the two ceilings mechanically: the pressed steel cage and balls tolerate 800 r/min while thermal balance under catalogue load sets the 600 r/min reference; at dm ≈ 380.0 mm the corresponding dn is approximately 304k mm·r/min. Large-size execution note: the F machined steel cage exists because the ball complement and pitch diameter of the biggest 512-series sizes are beyond pressed-cage guidance; the steel cage is machined from solid, ball-centred, and its heavier mass must be supported by genuine oil or grease flow at start-up — never mount an F bearing dry for a trial rotation. Mounting note for the 95 mm F stack: induction-heat the shaft washer only — the machined steel cage rides the balls and must never be tapped, and first rotation should be a slow unloaded bedding run before the working thrust goes on.",
    "applications": [
      "very heavy crane and ladle hooks",
      "marine gearbox thrust positions",
      "offshore and dock winch drums"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "machined steel cage scuffing on a dry first start-up, before grease or oil has reached the ball-centred guide surfaces",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "false brinelling of the stationary tracks while the machine stands under vibration"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 572 kN track before first rotation.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 320 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 47; for 51264 F a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 572/3000 kN figures belong to 51264 F specifically (the single flat machined steel execution of 51264); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51264-F?",
        "a": "51264 F measures 320 mm bore × 440 mm OD × 95 mm bearing height (12.598 × 17.323 × 3.74 in), mass about 45500 g. SKF 17000 ratings: C 572 kN, C0 3000 kN, Pu 56 kN, reference speed 600 r/min (thermal) and limiting speed 800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51264 F mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 64 encode the bore as 320 mm (code 64 × 5), the standard SKF bore-code rule shared with radial bearings. suffix F identifies a machined steel cage, ball-centred: fitted to the largest sizes of the assortment where the ball complement and centrifugal forces exceed what the stamped sheet-steel execution can guide. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51264-F lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 800 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51264-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 320×440×95 mm ISO 104 thrust-ball envelope with catalogue ratings within 10 %; 51264 M is the single-direction flat-seat, machined brass cage (M) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51264-F",
      "51264 F"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51264-M",
    "brand": "SKF",
    "manufacturer_designation": "51264 M",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 320,
    "D_mm": 440,
    "B_mm": 95,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 572,
    "static_load_kN": 3000,
    "fatigue_load_limit_kN": 56,
    "reference_speed_rpm": 600,
    "limiting_speed_rpm": 800,
    "max_rpm": 800,
    "weight_g": 45000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51264 M is SKF's 320 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 320×440×95 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 64 encode the bore as 320 mm (code 64 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 320×440×95 mm (12.598×17.323×3.74 in), 60.0 mm radial section, C 572 kN, C0 3000 kN, Pu 56 kN. reference speed 600 r/min (thermal) and limiting speed 800 r/min (mechanical), catalogue mass 45000 g. Speed-ratio note for this exact unit: the reference speed is 600 r/min against a 800 r/min limiting speed, a reference-to-limit ratio of 0.75. Mass and section check: 45000 g inside the 320×440×95 mm outline leaves a 60.0 mm radial section, and the 3000 kN static rating is 5.24× the dynamic rating — plan static safety and minimum preload against those figures. Minimum-load arithmetic: with dm ≈ 380.0 mm and factor A 47, Fam ≈ A·(n·dm/1000)² at the 600 r/min reference speed is about 2443.2 kN for 51264 M; below that preload the balls skid and smear the tracks. Sizing arithmetic on the 320 mm bore: 572 kN C over the 60.0 mm radial section gives 9.5 kN per section millimetre, and the 95 mm stack height is 1.58× that section — proportions typical of a 51200 thrust section. Load balance: C0 3000 kN against C 572 kN gives a 5.24 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 56 kN enters the adjusted-life check. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 45000 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 320 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "marine gearbox thrust positions",
      "offshore and dock winch drums"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 47; for 51264 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 320 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51264 against two-way load lifts the loose washer off its raceway.",
      "The 51264 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 320 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Ordering discipline for 51264: the catalogue page quotes 51264 M and its 572/3000 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51264-M?",
        "a": "51264 M measures 320 mm bore × 440 mm OD × 95 mm bearing height (12.598 × 17.323 × 3.74 in), mass about 45000 g. SKF 17000 ratings: C 572 kN, C0 3000 kN, Pu 56 kN, reference speed 600 r/min (thermal) and limiting speed 800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51264 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 64 encode the bore as 320 mm (code 64 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51264-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 47 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, M-cage product) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51264-F",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 320×440×95 mm ISO 104 thrust-ball envelope with catalogue ratings within 10 %; 51264 F is the single-direction flat-seat, machined steel ball-centred cage (F) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51264-M",
      "51264 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51168-M",
    "brand": "SKF",
    "manufacturer_designation": "51168 M",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 340,
    "D_mm": 420,
    "B_mm": 64,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 377,
    "static_load_kN": 1960,
    "fatigue_load_limit_kN": 37.5,
    "reference_speed_rpm": 800,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "weight_g": 20500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51168 M is SKF's 340 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 340×420×64 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 68 encode the bore as 340 mm (code 68 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 340×420×64 mm (13.386×16.535×2.52 in), 40.0 mm radial section, C 377 kN, C0 1960 kN, Pu 37.5 kN. reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical), catalogue mass 20500 g. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 20 at the 1,100 r/min limiting speed raises the required axial preload to about 3494.5 kN; the reference-speed value 1848.3 kN is the thermal design point. At the printed limiting speed of 1,100 r/min the mean pitch diameter dm ≈ 380.0 mm implies a dn value around 418k mm·r/min; the 800 r/min reference speed is the thermal-planning value under catalogue load. Speed band width for this size is 300 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 51168 M can actually run. Light-load floor: Pu = 37.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51168 M; the number is 10 % of the 377 kN dynamic rating. Static-first selection data: 1960 kN C0 spread across the 64 mm stack gives 30.6 kN of static rating per height millimetre, and the 20500 g mass/C0 ratio is about 10 g per static kN — crane-hook and screw positions are normally sized on these two figures. Machined-cage order-number note: the M brass cage is a one-piece ball-centred window cage, chosen at the heavy end of the section for speed and shock duty; it is heavier and stiffer than the pressed-steel execution of the smaller sizes and tolerates interrupted lubrication far better, which is why the catalogue restricts the M suffix to the large bores. At 20500 g the machined brass cage represents a meaningful fraction of total mass; balancing checks on high-speed 340 mm vertical shafts should use the actual M-execution weight, not the lighter pressed-cage catalogue value.",
    "applications": [
      "marine gearbox thrust positions",
      "very heavy crane and ladle hooks",
      "offshore and dock winch drums"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "brass cage-pocket smearing during long unloaded running with a marginal oil film",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 20; for 51168 M a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 377/1960 kN and the available 420 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 51168 M is a pure axial bearing: it must never be subjected to radial load — any radial force on the 340 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Ordering discipline for 51168: the catalogue page quotes 51168 M and its 377/1960 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51168-M?",
        "a": "51168 M measures 340 mm bore × 420 mm OD × 64 mm bearing height (13.386 × 16.535 × 2.52 in), mass about 20500 g. SKF 17000 ratings: C 377 kN, C0 1960 kN, Pu 37.5 kN, reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51168 M mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 68 encode the bore as 340 mm (code 68 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51168-M?",
        "a": "The 800 r/min reference speed is the thermal balance under catalogue load; the 1,100 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51168-M need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 20 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51168",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 340×420×64 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51168",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51168-M",
      "51168 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51268-F",
    "brand": "SKF",
    "manufacturer_designation": "51268 F",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 340,
    "D_mm": 460,
    "B_mm": 96,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel",
    "dynamic_load_kN": 605,
    "static_load_kN": 3200,
    "fatigue_load_limit_kN": 25.5,
    "reference_speed_rpm": 600,
    "limiting_speed_rpm": 800,
    "max_rpm": 800,
    "weight_g": 48500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51268 F is a SKF single-direction thrust ball bearing for a 340 mm seat, built to ISO 104, with a flat housing seating surface, 340×460×96 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 68 decodes to 340 mm (code 68 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the F suffix denotes a steel cage machined from solid and centred on the balls, reserved for the largest OD sizes whose ball mass is beyond pressed-cage guidance. Envelope 340×460×96 mm (13.386×18.11×3.78 in), 60.0 mm radial section, C 605 kN, C0 3200 kN, Pu 25.5 kN. reference speed 600 r/min (thermal) and limiting speed 800 r/min (mechanical), catalogue mass 48500 g. Selection figures for 51268 F: the C0/C ratio is 5.29, Pu 25.5 kN is about 4 % of C, and the catalogue mass works out to roughly 143 g per millimetre of bore; the printed minimum-load factor is A 53. Speed planning separates the two ceilings mechanically: the pressed steel cage and balls tolerate 800 r/min while thermal balance under catalogue load sets the 600 r/min reference; at dm ≈ 400.0 mm the corresponding dn is approximately 320k mm·r/min. Track-circle loading: per millimetre of mean track circumference the 605 kN dynamic rating corresponds to roughly 0.48 kN/mm of π·dm track, a useful comparison against the other dimension series of the 340 mm bore. Rating split for documentation: dynamic 605 kN (L10 life), static 3200 kN (safety factor s0), fatigue limit 25.5 kN (adjusted life) — three different uses of three different numbers for 51268 F, none interchangeable with another. At the printed limiting speed of 800 r/min the mean pitch diameter dm ≈ 400.0 mm implies a dn value around 320k mm·r/min; the 600 r/min reference speed is the thermal-planning value under catalogue load. Large-size execution note: the F machined steel cage exists because the ball complement and pitch diameter of the biggest 512-series sizes are beyond pressed-cage guidance; the steel cage is machined from solid, ball-centred, and its heavier mass must be supported by genuine oil or grease flow at start-up — never mount an F bearing dry for a trial rotation. The F execution appears only at the 340 mm top end of the range: the 460 mm OD ball complement is large enough that cage centrifugal forces dictate a machined guide, which is also why the 3200 kN C0 figure dominates selection of this order number.",
    "applications": [
      "offshore and dock winch drums",
      "very heavy crane and ladle hooks",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "machined steel cage scuffing on a dry first start-up, before grease or oil has reached the ball-centred guide surfaces",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 53; for 51268 F a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The 51268 F is a pure axial bearing: it must never be subjected to radial load — any radial force on the 340 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 340 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 605 kN track before first rotation.",
      "Ordering discipline for 51268: the catalogue page quotes 51268 F and its 605/3200 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51268-F?",
        "a": "Boundary dimensions to ISO 104: bore 340 mm, OD 460 mm, height 96 mm; weight 48500 g. Load figures from SKF 17000: dynamic 605 kN, static 3200 kN, fatigue limit 25.5 kN; reference speed 600 r/min (thermal) and limiting speed 800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51268 F mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 68 decodes to 340 mm (code 68 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the F suffix denotes a steel cage machined from solid and centred on the balls, reserved for the largest OD sizes whose ball mass is beyond pressed-cage guidance. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51268-F?",
        "a": "The 600 r/min reference speed is the thermal balance under catalogue load; the 800 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51268-F need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 53 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51268",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51268-F",
      "51268 F"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51172-F",
    "brand": "SKF",
    "manufacturer_designation": "51172 F",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 360,
    "D_mm": 440,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel",
    "dynamic_load_kN": 390,
    "static_load_kN": 2080,
    "fatigue_load_limit_kN": 38,
    "reference_speed_rpm": 750,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "weight_g": 22000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51172 F is a SKF single-direction thrust ball bearing for a 360 mm seat, built to ISO 104, with a flat housing seating surface, 360×440×65 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 72 decodes to 360 mm (code 72 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the F suffix denotes a steel cage machined from solid and centred on the balls, reserved for the largest OD sizes whose ball mass is beyond pressed-cage guidance. Envelope 360×440×65 mm (14.173×17.323×2.559 in), 40.0 mm radial section, C 390 kN, C0 2080 kN, Pu 38 kN. reference speed 750 r/min (thermal) and limiting speed 1,100 r/min (mechanical), catalogue mass 22000 g. Track-circle loading: per millimetre of mean track circumference the 390 kN dynamic rating corresponds to roughly 0.31 kN/mm of π·dm track, a useful comparison against the other dimension series of the 360 mm bore. Section proportions: the 40.0 mm radial section compares with 360 mm of bore (section/bore ≈ 0.11) and the 65 mm height is 1.63× that section — the proportions that identify the 51100 envelope at a glance. Static-first selection data: 2080 kN C0 spread across the 65 mm stack gives 32.0 kN of static rating per height millimetre, and the 22000 g mass/C0 ratio is about 11 g per static kN — crane-hook and screw positions are normally sized on these two figures. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 22 at the 1,100 r/min limiting speed raises the required axial preload to about 4259.2 kN; the reference-speed value 1980.0 kN is the thermal design point. Speed band width for this size is 350 r/min between reference and limiting (1.47× ratio); lubrication, preload and heat removal decide where inside that band 51172 F can actually run. Large-size execution note: the F machined steel cage exists because the ball complement and pitch diameter of the biggest 512-series sizes are beyond pressed-cage guidance; the steel cage is machined from solid, ball-centred, and its heavier mass must be supported by genuine oil or grease flow at start-up — never mount an F bearing dry for a trial rotation. The F execution appears only at the 360 mm top end of the range: the 440 mm OD ball complement is large enough that cage centrifugal forces dictate a machined guide, which is also why the 2080 kN C0 figure dominates selection of this order number.",
    "applications": [
      "offshore and dock winch drums",
      "very heavy crane and ladle hooks",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "machined steel cage scuffing on a dry first start-up, before grease or oil has reached the ball-centred guide surfaces",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 390 kN track before first rotation.",
      "When the housing seat cannot be machined square to the 360 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 22; for 51172 F a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 390/2080 kN and the available 440 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The 390/2080 kN figures belong to 51172 F specifically (the single flat machined steel execution of 51172); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51172-F?",
        "a": "Boundary dimensions to ISO 104: bore 360 mm, OD 440 mm, height 65 mm; weight 22000 g. Load figures from SKF 17000: dynamic 390 kN, static 2080 kN, fatigue limit 38 kN; reference speed 750 r/min (thermal) and limiting speed 1,100 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51172 F mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 72 decodes to 360 mm (code 72 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the F suffix denotes a steel cage machined from solid and centred on the balls, reserved for the largest OD sizes whose ball mass is beyond pressed-cage guidance. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, F-cage product) uses the standard stamped sheet-steel pressed cage."
      },
      {
        "q": "Can 51172-F carry radial load?",
        "a": "No — thrust ball bearings are designed for pure axial load. Any radial force on the 360 mm shaft must go to a separate radial bearing; mixed loading through 51172 F edge-loads the balls and destroys the washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51172",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 360×440×65 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51172",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51172-F",
      "51172 F"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51272-F",
    "brand": "SKF",
    "manufacturer_designation": "51272 F",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 360,
    "D_mm": 500,
    "B_mm": 110,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel",
    "dynamic_load_kN": 741,
    "static_load_kN": 4150,
    "fatigue_load_limit_kN": 73.5,
    "reference_speed_rpm": 500,
    "limiting_speed_rpm": 700,
    "max_rpm": 700,
    "weight_g": 70000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51200 series order number 51272 F is a SKF single-direction thrust ball bearing for a 360 mm seat, built to ISO 104, with a flat housing seating surface, 360×500×110 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 72 decodes to 360 mm (code 72 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the F suffix denotes a steel cage machined from solid and centred on the balls, reserved for the largest OD sizes whose ball mass is beyond pressed-cage guidance. Envelope 360×500×110 mm (14.173×19.685×4.331 in), 70.0 mm radial section, C 741 kN, C0 4150 kN, Pu 73.5 kN. reference speed 500 r/min (thermal) and limiting speed 700 r/min (mechanical), catalogue mass 70000 g. Pitch-diameter arithmetic: dm = (360+500)/2 = 430.0 mm; at the 700 r/min limiting speed that corresponds to roughly 301k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Light-load floor: Pu = 73.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 51272 F; the number is 10 % of the 741 kN dynamic rating. Bore-to-OD planning: OD 500 over bore 360 is a 1.39× step for this size, and the 110 mm height gives a bore/height ratio of 3.27; use these ratios when the housing recess around the 360 mm shaft is the first constraint. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 90 at the 700 r/min limiting speed raises the required axial preload to about 8154.1 kN; the reference-speed value 4160.3 kN is the thermal design point. Sizing arithmetic on the 360 mm bore: 741 kN C over the 70.0 mm radial section gives 10.6 kN per section millimetre, and the 110 mm stack height is 1.57× that section — proportions typical of a 51200 thrust section. Large-size execution note: the F machined steel cage exists because the ball complement and pitch diameter of the biggest 512-series sizes are beyond pressed-cage guidance; the steel cage is machined from solid, ball-centred, and its heavier mass must be supported by genuine oil or grease flow at start-up — never mount an F bearing dry for a trial rotation. The F execution appears only at the 360 mm top end of the range: the 500 mm OD ball complement is large enough that cage centrifugal forces dictate a machined guide, which is also why the 4150 kN C0 figure dominates selection of this order number.",
    "applications": [
      "offshore and dock winch drums",
      "heavy converter and ladle-tilt pivots",
      "very heavy crane and ladle hooks"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "machined steel cage scuffing on a dry first start-up, before grease or oil has reached the ball-centred guide surfaces",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 90; for 51272 F a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 360 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The 51272 F is a pure axial bearing: it must never be subjected to radial load — any radial force on the 360 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 741 kN track before first rotation.",
      "Ordering discipline for 51272: the catalogue page quotes 51272 F and its 741/4150 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51272-F?",
        "a": "Boundary dimensions to ISO 104: bore 360 mm, OD 500 mm, height 110 mm; weight 70000 g. Load figures from SKF 17000: dynamic 741 kN, static 4150 kN, fatigue limit 73.5 kN; reference speed 500 r/min (thermal) and limiting speed 700 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51272 F mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 72 decodes to 360 mm (code 72 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the F suffix denotes a steel cage machined from solid and centred on the balls, reserved for the largest OD sizes whose ball mass is beyond pressed-cage guidance. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51272-F need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 90 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, F-cage product) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51272",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51272-F",
      "51272 F"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51176-F",
    "brand": "SKF",
    "manufacturer_designation": "51176 F",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 380,
    "D_mm": 460,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel",
    "dynamic_load_kN": 397,
    "static_load_kN": 2200,
    "fatigue_load_limit_kN": 40,
    "reference_speed_rpm": 750,
    "limiting_speed_rpm": 1000,
    "max_rpm": 1000,
    "weight_g": 23000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51176 F is an ISO 104 single-direction thrust ball bearing, 380 mm bore and 460 mm OD on a flat housing seat, standing 65 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 76: bore 380 mm (code 76 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. F-cage execution: a solid machined steel ball-centred retainer for the biggest thrust-ball sizes, where rigidity and cage guidance dominate over the lightness of sheet steel. Envelope 380×460×65 mm (14.961×18.11×2.559 in), 40.0 mm radial section, C 397 kN, C0 2200 kN, Pu 40 kN. reference speed 750 r/min (thermal) and limiting speed 1,000 r/min (mechanical), catalogue mass 23000 g. At the printed limiting speed of 1,000 r/min the mean pitch diameter dm ≈ 420.0 mm implies a dn value around 420k mm·r/min; the 750 r/min reference speed is the thermal-planning value under catalogue load. Section proportions: the 40.0 mm radial section compares with 380 mm of bore (section/bore ≈ 0.11) and the 65 mm height is 1.63× that section — the proportions that identify the 51100 envelope at a glance. Sizing arithmetic on the 380 mm bore: 397 kN C over the 40.0 mm radial section gives 9.9 kN per section millimetre, and the 65 mm stack height is 1.63× that section — proportions typical of a 51100 thrust section. Pitch-diameter arithmetic: dm = (380+460)/2 = 420.0 mm; at the 1,000 r/min limiting speed that corresponds to roughly 420k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51176 F covers about 52,779 mm², distributing C0 2200 kN over a mean track circle of π·dm ≈ 1,319 mm. Large-size execution note: the F machined steel cage exists because the ball complement and pitch diameter of the biggest 512-series sizes are beyond pressed-cage guidance; the steel cage is machined from solid, ball-centred, and its heavier mass must be supported by genuine oil or grease flow at start-up — never mount an F bearing dry for a trial rotation. The F execution appears only at the 380 mm top end of the range: the 460 mm OD ball complement is large enough that cage centrifugal forces dictate a machined guide, which is also why the 2200 kN C0 figure dominates selection of this order number.",
    "applications": [
      "offshore and dock winch drums",
      "heavy converter and ladle-tilt pivots",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "machined steel cage scuffing on a dry first start-up, before grease or oil has reached the ball-centred guide surfaces",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "washer face scoring from swarf trapped between the loose housing washer and its register"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 65 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 380 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 25; for 51176 F a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51176 F as the single flat machined steel execution; other order numbers of the 51176 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51176-F?",
        "a": "The catalogue envelope is 380×460×65 mm, mass 23000 g; ratings C 397 kN / C0 2200 kN / Pu 40 kN, reference speed 750 r/min (thermal) and limiting speed 1,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51176 F mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 76: bore 380 mm (code 76 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. F-cage execution: a solid machined steel ball-centred retainer for the biggest thrust-ball sizes, where rigidity and cage guidance dominate over the lightness of sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 380 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      },
      {
        "q": "Can a single 51176 take thrust in both directions?",
        "a": "No. It reacts axial force in one direction; reversing duty needs a mirrored pair of single-direction bearings or a 52-series double-direction unit, which packages one shaft washer, two housing washers and two cage sets."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51176",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 380×460×65 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51176",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51176-F",
      "51176 F"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51276-F",
    "brand": "SKF",
    "manufacturer_designation": "51276 F",
    "series": "51200-series",
    "type": "thrust_ball",
    "d_mm": 380,
    "D_mm": 520,
    "B_mm": 112,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel",
    "dynamic_load_kN": 728,
    "static_load_kN": 4150,
    "fatigue_load_limit_kN": 72,
    "reference_speed_rpm": 500,
    "limiting_speed_rpm": 700,
    "max_rpm": 700,
    "weight_g": 73000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51276 F is SKF's 380 mm-bore single-direction thrust ball bearing in the 51200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 380×520×112 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 76 encode the bore as 380 mm (code 76 × 5), the standard SKF bore-code rule shared with radial bearings. suffix F identifies a machined steel cage, ball-centred: fitted to the largest sizes of the assortment where the ball complement and centrifugal forces exceed what the stamped sheet-steel execution can guide. Envelope 380×520×112 mm (14.961×20.472×4.409 in), 70.0 mm radial section, C 728 kN, C0 4150 kN, Pu 72 kN. reference speed 500 r/min (thermal) and limiting speed 700 r/min (mechanical), catalogue mass 73000 g. Bore-to-OD planning: OD 520 over bore 380 is a 1.37× step for this size, and the 112 mm height gives a bore/height ratio of 3.39; use these ratios when the housing recess around the 380 mm shaft is the first constraint. Mass and section check: 73000 g inside the 380×520×112 mm outline leaves a 70.0 mm radial section, and the 4150 kN static rating is 5.70× the dynamic rating — plan static safety and minimum preload against those figures. Rating split for documentation: dynamic 728 kN (L10 life), static 4150 kN (safety factor s0), fatigue limit 72 kN (adjusted life) — three different uses of three different numbers for 51276 F, none interchangeable with another. Sizing arithmetic on the 380 mm bore: 728 kN C over the 70.0 mm radial section gives 10.4 kN per section millimetre, and the 112 mm stack height is 1.60× that section — proportions typical of a 51200 thrust section. Imperial cross-check for procurement drawings: 14.961 in bore, 20.472 in OD, 4.409 in height, and the 73000 g catalogue mass converts to 73.000 kg (2575.0 oz). Large-size execution note: the F machined steel cage exists because the ball complement and pitch diameter of the biggest 512-series sizes are beyond pressed-cage guidance; the steel cage is machined from solid, ball-centred, and its heavier mass must be supported by genuine oil or grease flow at start-up — never mount an F bearing dry for a trial rotation. Mounting note for the 112 mm F stack: induction-heat the shaft washer only — the machined steel cage rides the balls and must never be tapped, and first rotation should be a slow unloaded bedding run before the working thrust goes on.",
    "applications": [
      "large press rams and screwdown mechanisms",
      "very heavy crane and ladle hooks",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "machined steel cage scuffing on a dry first start-up, before grease or oil has reached the ball-centred guide surfaces",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Heat the shaft washer to at most 120 °C for mounting, or press it via a sleeve on its ground bore — force applied through the housing washer or the ball set brinells the 728 kN track before first rotation.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 112 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51276 against two-way load lifts the loose washer off its raceway.",
      "The 728/4150 kN figures belong to 51276 F specifically (the single flat machined steel execution of 51276); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51276-F?",
        "a": "51276 F measures 380 mm bore × 520 mm OD × 112 mm bearing height (14.961 × 20.472 × 4.409 in), mass about 73000 g. SKF 17000 ratings: C 728 kN, C0 4150 kN, Pu 72 kN, reference speed 500 r/min (thermal) and limiting speed 700 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51276 F mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 76 encode the bore as 380 mm (code 76 × 5), the standard SKF bore-code rule shared with radial bearings. suffix F identifies a machined steel cage, ball-centred: fitted to the largest sizes of the assortment where the ball complement and centrifugal forces exceed what the stamped sheet-steel execution can guide. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51276-F lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 700 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 380 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51276",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51276-F",
      "51276 F"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51180-F",
    "brand": "SKF",
    "manufacturer_designation": "51180 F",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 400,
    "D_mm": 480,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel",
    "dynamic_load_kN": 403,
    "static_load_kN": 2280,
    "fatigue_load_limit_kN": 40.5,
    "reference_speed_rpm": 700,
    "limiting_speed_rpm": 1000,
    "max_rpm": 1000,
    "weight_g": 24000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 51180 F is an ISO 104 single-direction thrust ball bearing, 400 mm bore and 480 mm OD on a flat housing seat, standing 65 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 80: bore 400 mm (code 80 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. F-cage execution: a solid machined steel ball-centred retainer for the biggest thrust-ball sizes, where rigidity and cage guidance dominate over the lightness of sheet steel. Envelope 400×480×65 mm (15.748×18.898×2.559 in), 40.0 mm radial section, C 403 kN, C0 2280 kN, Pu 40.5 kN. reference speed 700 r/min (thermal) and limiting speed 1,000 r/min (mechanical), catalogue mass 24000 g. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51180 F covers about 55,292 mm², distributing C0 2280 kN over a mean track circle of π·dm ≈ 1,382 mm. Mass and section check: 24000 g inside the 400×480×65 mm outline leaves a 40.0 mm radial section, and the 2280 kN static rating is 5.66× the dynamic rating — plan static safety and minimum preload against those figures. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 27 at the 1,000 r/min limiting speed raises the required axial preload to about 5227.2 kN; the reference-speed value 2561.3 kN is the thermal design point. At the printed limiting speed of 1,000 r/min the mean pitch diameter dm ≈ 440.0 mm implies a dn value around 440k mm·r/min; the 700 r/min reference speed is the thermal-planning value under catalogue load. Pitch-diameter arithmetic: dm = (400+480)/2 = 440.0 mm; at the 1,000 r/min limiting speed that corresponds to roughly 440k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Large-size execution note: the F machined steel cage exists because the ball complement and pitch diameter of the biggest 512-series sizes are beyond pressed-cage guidance; the steel cage is machined from solid, ball-centred, and its heavier mass must be supported by genuine oil or grease flow at start-up — never mount an F bearing dry for a trial rotation. Mounting note for the 65 mm F stack: induction-heat the shaft washer only — the machined steel cage rides the balls and must never be tapped, and first rotation should be a slow unloaded bedding run before the working thrust goes on.",
    "applications": [
      "heavy converter and ladle-tilt pivots",
      "marine gearbox thrust positions",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "machined steel cage scuffing on a dry first start-up, before grease or oil has reached the ball-centred guide surfaces",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 403/2280 kN and the available 480 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51180 against two-way load lifts the loose washer off its raceway.",
      "The 51180 F is a pure axial bearing: it must never be subjected to radial load — any radial force on the 400 mm shaft has to be carried by a radial bearing mounted alongside it.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 400 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Ordering discipline for 51180: the catalogue page quotes 51180 F and its 403/2280 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51180-F?",
        "a": "The catalogue envelope is 400×480×65 mm, mass 24000 g; ratings C 403 kN / C0 2280 kN / Pu 40.5 kN, reference speed 700 r/min (thermal) and limiting speed 1,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51180 F mean?",
        "a": "51xxx breaks down as 5 for thrust ball, 1 for one load direction on a flat seat, a section digit 1–4 light-to-heavy, then the two-digit bore code. reading the ending 80: bore 400 mm (code 80 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. F-cage execution: a solid machined steel ball-centred retainer for the biggest thrust-ball sizes, where rigidity and cage guidance dominate over the lightness of sheet steel. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51180-F need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 27 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, F-cage product) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51180",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 400×480×65 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51180",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51180-F",
      "51180 F"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51184-F",
    "brand": "SKF",
    "manufacturer_designation": "51184 F",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 420,
    "D_mm": 500,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel",
    "dynamic_load_kN": 410,
    "static_load_kN": 2400,
    "fatigue_load_limit_kN": 41.5,
    "reference_speed_rpm": 700,
    "limiting_speed_rpm": 1000,
    "max_rpm": 1000,
    "weight_g": 25500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51184 F is a SKF single-direction thrust ball bearing for a 420 mm seat, built to ISO 104, with a flat housing seating surface, 420×500×65 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 84 decodes to 420 mm (code 84 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the F suffix denotes a steel cage machined from solid and centred on the balls, reserved for the largest OD sizes whose ball mass is beyond pressed-cage guidance. Envelope 420×500×65 mm (16.535×19.685×2.559 in), 40.0 mm radial section, C 410 kN, C0 2400 kN, Pu 41.5 kN. reference speed 700 r/min (thermal) and limiting speed 1,000 r/min (mechanical), catalogue mass 25500 g. Speed band width for this size is 300 r/min between reference and limiting (1.43× ratio); lubrication, preload and heat removal decide where inside that band 51184 F can actually run. Rating split for documentation: dynamic 410 kN (L10 life), static 2400 kN (safety factor s0), fatigue limit 41.5 kN (adjusted life) — three different uses of three different numbers for 51184 F, none interchangeable with another. At the printed limiting speed of 1,000 r/min the mean pitch diameter dm ≈ 460.0 mm implies a dn value around 460k mm·r/min; the 700 r/min reference speed is the thermal-planning value under catalogue load. Mass and section check: 25500 g inside the 420×500×65 mm outline leaves a 40.0 mm radial section, and the 2400 kN static rating is 5.85× the dynamic rating — plan static safety and minimum preload against those figures. Bore-to-OD planning: OD 500 over bore 420 is a 1.19× step for this size, and the 65 mm height gives a bore/height ratio of 6.46; use these ratios when the housing recess around the 420 mm shaft is the first constraint. Large-size execution note: the F machined steel cage exists because the ball complement and pitch diameter of the biggest 512-series sizes are beyond pressed-cage guidance; the steel cage is machined from solid, ball-centred, and its heavier mass must be supported by genuine oil or grease flow at start-up — never mount an F bearing dry for a trial rotation. The F execution appears only at the 420 mm top end of the range: the 500 mm OD ball complement is large enough that cage centrifugal forces dictate a machined guide, which is also why the 2400 kN C0 figure dominates selection of this order number.",
    "applications": [
      "heavy converter and ladle-tilt pivots",
      "marine gearbox thrust positions",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "machined steel cage scuffing on a dry first start-up, before grease or oil has reached the ball-centred guide surfaces",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51184 against two-way load lifts the loose washer off its raceway.",
      "When the housing seat cannot be machined square to the 420 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "Keep the applied thrust above Fam ≈ A·(n·dm/1000)² with the printed factor A 30; for 51184 F a spring preload or the rotor weight is part of the selection at light load and high speed, because unloaded balls skid rather than roll.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 420 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51184 F as the single flat machined steel execution; other order numbers of the 51184 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51184-F?",
        "a": "Boundary dimensions to ISO 104: bore 420 mm, OD 500 mm, height 65 mm; weight 25500 g. Load figures from SKF 17000: dynamic 410 kN, static 2400 kN, fatigue limit 41.5 kN; reference speed 700 r/min (thermal) and limiting speed 1,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51184 F mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 84 decodes to 420 mm (code 84 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the F suffix denotes a steel cage machined from solid and centred on the balls, reserved for the largest OD sizes whose ball mass is beyond pressed-cage guidance. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "How is 51184-F lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 1,000 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      },
      {
        "q": "Which way round do the washers go?",
        "a": "The shaft washer has the smaller, ground bore and is fitted tight on the 420 mm shaft; the housing washer has the larger loose bore and sits in the register. Load must press the shaft washer towards the housing washer through the ball-cage set — reverse fitting makes the loose washer rotate with the shaft."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51184",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 420×500×65 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51184",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51184-F",
      "51184 F"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51188-F",
    "brand": "SKF",
    "manufacturer_designation": "51188 F",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 440,
    "D_mm": 540,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel",
    "dynamic_load_kN": 527,
    "static_load_kN": 3250,
    "fatigue_load_limit_kN": 55,
    "reference_speed_rpm": 600,
    "limiting_speed_rpm": 850,
    "max_rpm": 850,
    "weight_g": 42000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 51100 series order number 51188 F is a SKF single-direction thrust ball bearing for a 440 mm seat, built to ISO 104, with a flat housing seating surface, 440×540×80 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 88 decodes to 440 mm (code 88 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the F suffix denotes a steel cage machined from solid and centred on the balls, reserved for the largest OD sizes whose ball mass is beyond pressed-cage guidance. Envelope 440×540×80 mm (17.323×21.26×3.15 in), 50.0 mm radial section, C 527 kN, C0 3250 kN, Pu 55 kN. reference speed 600 r/min (thermal) and limiting speed 850 r/min (mechanical), catalogue mass 42000 g. Washer-annulus check: the π/4·(D²−d²) contact annulus of 51188 F covers about 76,969 mm², distributing C0 3250 kN over a mean track circle of π·dm ≈ 1,539 mm. Speed band width for this size is 250 r/min between reference and limiting (1.42× ratio); lubrication, preload and heat removal decide where inside that band 51188 F can actually run. Mass and section check: 42000 g inside the 440×540×80 mm outline leaves a 50.0 mm radial section, and the 3250 kN static rating is 6.17× the dynamic rating — plan static safety and minimum preload against those figures. Rating split for documentation: dynamic 527 kN (L10 life), static 3250 kN (safety factor s0), fatigue limit 55 kN (adjusted life) — three different uses of three different numbers for 51188 F, none interchangeable with another. Selection figures for 51188 F: the C0/C ratio is 6.17, Pu 55 kN is about 10 % of C, and the catalogue mass works out to roughly 95 g per millimetre of bore; the printed minimum-load factor is A 55. Large-size execution note: the F machined steel cage exists because the ball complement and pitch diameter of the biggest 512-series sizes are beyond pressed-cage guidance; the steel cage is machined from solid, ball-centred, and its heavier mass must be supported by genuine oil or grease flow at start-up — never mount an F bearing dry for a trial rotation. Mounting note for the 80 mm F stack: induction-heat the shaft washer only — the machined steel cage rides the balls and must never be tapped, and first rotation should be a slow unloaded bedding run before the working thrust goes on.",
    "applications": [
      "marine gearbox thrust positions",
      "offshore and dock winch drums",
      "large press rams and screwdown mechanisms"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "machined steel cage scuffing on a dry first start-up, before grease or oil has reached the ball-centred guide surfaces",
      "track rust staining from condensate during long idle periods in humid plant air",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 80 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "When the housing seat cannot be machined square to the 440 mm shaft, the sphered 53-series execution of this size with its U seat washer is the self-aligning counterpart of this flat 51100 bearing.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 527/3250 kN and the available 540 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51188 F as the single flat machined steel execution; other order numbers of the 51188 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51188-F?",
        "a": "Boundary dimensions to ISO 104: bore 440 mm, OD 540 mm, height 80 mm; weight 42000 g. Load figures from SKF 17000: dynamic 527 kN, static 3250 kN, fatigue limit 55 kN; reference speed 600 r/min (thermal) and limiting speed 850 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51188 F mean?",
        "a": "reading 51xxx as a code: the 1 after 5 identifies one load direction and a flat seat, and the next digit ranks the section 1 (light) to 4 (heavy) before the two-digit bore code. bore code 88 decodes to 440 mm (code 88 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the F suffix denotes a steel cage machined from solid and centred on the balls, reserved for the largest OD sizes whose ball mass is beyond pressed-cage guidance. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What minimum axial load does 51188-F need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 55 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What do the M and F suffixes mean?",
        "a": "M is a machined brass ball-centred cage and F a machined steel ball-centred cage, both reserved for larger sizes and severer duty; the suffix-free execution (this order number is a different, F-cage product) uses the standard stamped sheet-steel pressed cage."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51188",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 440×540×80 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51188",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51188-F",
      "51188 F"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51192-F",
    "brand": "SKF",
    "manufacturer_designation": "51192 F",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 460,
    "D_mm": 560,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel",
    "dynamic_load_kN": 527,
    "static_load_kN": 3250,
    "fatigue_load_limit_kN": 54,
    "reference_speed_rpm": 600,
    "limiting_speed_rpm": 800,
    "max_rpm": 800,
    "weight_g": 43500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51192 F is SKF's 460 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 460×560×80 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 92 encode the bore as 460 mm (code 92 × 5), the standard SKF bore-code rule shared with radial bearings. suffix F identifies a machined steel cage, ball-centred: fitted to the largest sizes of the assortment where the ball complement and centrifugal forces exceed what the stamped sheet-steel execution can guide. Envelope 460×560×80 mm (18.11×22.047×3.15 in), 50.0 mm radial section, C 527 kN, C0 3250 kN, Pu 54 kN. reference speed 600 r/min (thermal) and limiting speed 800 r/min (mechanical), catalogue mass 43500 g. Section proportions: the 50.0 mm radial section compares with 460 mm of bore (section/bore ≈ 0.11) and the 80 mm height is 1.60× that section — the proportions that identify the 51100 envelope at a glance. Imperial cross-check for procurement drawings: 18.11 in bore, 22.047 in OD, 3.15 in height, and the 43500 g catalogue mass converts to 43.500 kg (1534.4 oz). Static-first selection data: 3250 kN C0 spread across the 80 mm stack gives 40.6 kN of static rating per height millimetre, and the 43500 g mass/C0 ratio is about 13 g per static kN — crane-hook and screw positions are normally sized on these two figures. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 55 at the 800 r/min limiting speed raises the required axial preload to about 9155.5 kN; the reference-speed value 5150.0 kN is the thermal design point. Selection figures for 51192 F: the C0/C ratio is 6.17, Pu 54 kN is about 10 % of C, and the catalogue mass works out to roughly 95 g per millimetre of bore; the printed minimum-load factor is A 55. Large-size execution note: the F machined steel cage exists because the ball complement and pitch diameter of the biggest 512-series sizes are beyond pressed-cage guidance; the steel cage is machined from solid, ball-centred, and its heavier mass must be supported by genuine oil or grease flow at start-up — never mount an F bearing dry for a trial rotation. The F execution appears only at the 460 mm top end of the range: the 560 mm OD ball complement is large enough that cage centrifugal forces dictate a machined guide, which is also why the 3250 kN C0 figure dominates selection of this order number.",
    "applications": [
      "heavy converter and ladle-tilt pivots",
      "large press rams and screwdown mechanisms",
      "offshore and dock winch drums"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "machined steel cage scuffing on a dry first start-up, before grease or oil has reached the ball-centred guide surfaces",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51192 against two-way load lifts the loose washer off its raceway.",
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "The third digit grades the section: 511 light, then 512, 513 and 514 progressively taller and heavier at the same bore — select from 527/3250 kN and the available 560 mm OD, never substitute a lighter series for a heavier one without rechecking C and C0.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 460 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 51192 F as the single flat machined steel execution; other order numbers of the 51192 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51192-F?",
        "a": "51192 F measures 460 mm bore × 560 mm OD × 80 mm bearing height (18.11 × 22.047 × 3.15 in), mass about 43500 g. SKF 17000 ratings: C 527 kN, C0 3250 kN, Pu 54 kN, reference speed 600 r/min (thermal) and limiting speed 800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51192 F mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 92 encode the bore as 460 mm (code 92 × 5), the standard SKF bore-code rule shared with radial bearings. suffix F identifies a machined steel cage, ball-centred: fitted to the largest sizes of the assortment where the ball complement and centrifugal forces exceed what the stamped sheet-steel execution can guide. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What is the difference between the 511, 512, 513 and 514 series?",
        "a": "All are single-direction flat-seat thrust ball bearings; the third digit grades the dimension series from light section (511) to heavy (514). At the same bore a 514 is taller, larger in OD and far higher rated than a 511, so series are not interchangeable without rechecking dimensions and ratings."
      },
      {
        "q": "How is 51192-F lubricated?",
        "a": "Grease is standard at the small and medium end — fill the housing recess sparingly so churning does not push the loose washer off its seat; oil bath or circulation is normal near the 800 r/min limiting speed and on vertical shafts, where the upper washer would otherwise run dry."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51192",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "51192",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51192-F",
      "51192 F"
    ],
    "locale_variants": {}
  },
  {
    "sku": "51196-F",
    "brand": "SKF",
    "manufacturer_designation": "51196 F",
    "series": "51100-series",
    "type": "thrust_ball",
    "d_mm": 480,
    "D_mm": 580,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel",
    "dynamic_load_kN": 540,
    "static_load_kN": 3550,
    "fatigue_load_limit_kN": 56,
    "reference_speed_rpm": 560,
    "limiting_speed_rpm": 800,
    "max_rpm": 800,
    "weight_g": 45500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "51196 F is SKF's 480 mm-bore single-direction thrust ball bearing in the 51100 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 480×580×80 mm. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 96 encode the bore as 480 mm (code 96 × 5), the standard SKF bore-code rule shared with radial bearings. suffix F identifies a machined steel cage, ball-centred: fitted to the largest sizes of the assortment where the ball complement and centrifugal forces exceed what the stamped sheet-steel execution can guide. Envelope 480×580×80 mm (18.898×22.835×3.15 in), 50.0 mm radial section, C 540 kN, C0 3550 kN, Pu 56 kN. reference speed 560 r/min (thermal) and limiting speed 800 r/min (mechanical), catalogue mass 45500 g. Capacity density: 540 kN C from 45.500 kg of bearing steel gives about 11.9 kN per kilogram; static density is correspondingly 78.0 kN/kg at C0 3550 kN. Track-circle loading: per millimetre of mean track circumference the 540 kN dynamic rating corresponds to roughly 0.32 kN/mm of π·dm track, a useful comparison against the other dimension series of the 480 mm bore. Mass and section check: 45500 g inside the 480×580×80 mm outline leaves a 50.0 mm radial section, and the 3550 kN static rating is 6.57× the dynamic rating — plan static safety and minimum preload against those figures. Sizing arithmetic on the 480 mm bore: 540 kN C over the 50.0 mm radial section gives 10.8 kN per section millimetre, and the 80 mm stack height is 1.60× that section — proportions typical of a 51100 thrust section. At the printed limiting speed of 800 r/min the mean pitch diameter dm ≈ 530.0 mm implies a dn value around 424k mm·r/min; the 560 r/min reference speed is the thermal-planning value under catalogue load. Large-size execution note: the F machined steel cage exists because the ball complement and pitch diameter of the biggest 512-series sizes are beyond pressed-cage guidance; the steel cage is machined from solid, ball-centred, and its heavier mass must be supported by genuine oil or grease flow at start-up — never mount an F bearing dry for a trial rotation. Mounting note for the 80 mm F stack: induction-heat the shaft washer only — the machined steel cage rides the balls and must never be tapped, and first rotation should be a slow unloaded bedding run before the working thrust goes on.",
    "applications": [
      "heavy converter and ladle-tilt pivots",
      "large press rams and screwdown mechanisms",
      "marine gearbox thrust positions"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "machined steel cage scuffing on a dry first start-up, before grease or oil has reached the ball-centred guide surfaces",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The three components are separable and interchangeable within the ISO 104 size, but keep this bearing's parts together in service and never combine washers from different manufacturers or a worn washer with a new ball set.",
      "A 51-series bearing reacts thrust in one direction only — reversing positions need a mirrored single-direction pair or a 52-series double-direction unit; fitting a single 51196 against two-way load lifts the loose washer off its raceway.",
      "Identify the washers before fitting: the shaft washer has the ground, smaller bore and takes an interference fit on the 480 mm shaft, while the housing washer bore is larger and runs loose; swapping them locks the ball set and burns the tracks.",
      "On vertical shafts retain the loose housing washer positively with a cover or ring and verify the grease fill does not drain out of the 80 mm stack; thrust-ball bearings on horizontal shafts should have the shaft washer (the tight one) against the rotating element.",
      "The 540/3550 kN figures belong to 51196 F specifically (the single flat machined steel execution of 51196); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 51196-F?",
        "a": "51196 F measures 480 mm bore × 580 mm OD × 80 mm bearing height (18.898 × 22.835 × 3.15 in), mass about 45500 g. SKF 17000 ratings: C 540 kN, C0 3550 kN, Pu 56 kN, reference speed 560 r/min (thermal) and limiting speed 800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 51196 F mean?",
        "a": "in the 51xxx designation the first 1 marks a single-direction bearing with a flat housing seating surface; the third digit 1–4 grades the dimension series from the light 511 section through the heavy 514 section. the final two digits 96 encode the bore as 480 mm (code 96 × 5), the standard SKF bore-code rule shared with radial bearings. suffix F identifies a machined steel cage, ball-centred: fitted to the largest sizes of the assortment where the ball complement and centrifugal forces exceed what the stamped sheet-steel execution can guide. 5 = thrust ball bearing, 1 = single direction with flat seating surface."
      },
      {
        "q": "What do the two published speeds mean for 51196-F?",
        "a": "The 560 r/min reference speed is the thermal balance under catalogue load; the 800 r/min limiting speed is the mechanical cage/ball ceiling. Preload, lubrication and cooling move the real limits, so both are catalogue-condition figures."
      },
      {
        "q": "What minimum axial load does 51196-F need?",
        "a": "SKF gives Fam ≈ A·(n·dm/1000)² with factor A 66 printed for this size; below it the balls skid. Spring preload, a cover spring or the rotor's own weight are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51196",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 480×580×80 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "51196",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "51196-F",
      "51196 F"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53201",
    "brand": "SKF",
    "manufacturer_designation": "53201",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 12,
    "D_mm": 28,
    "B_mm": 11.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 13.3,
    "static_load_kN": 20.8,
    "fatigue_load_limit_kN": 0.765,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 45,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53201 is an ISO 104 single-direction thrust ball bearing, 12 mm bore and 28 mm OD, with a sphered housing washer and U seat washer, standing 11.4 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 01: bore 12 mm for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 12×28×11.4 mm (0.472×1.102×0.449 in), 8.0 mm radial section, C 13.3 kN, C0 20.8 kN, Pu 0.765 kN. Mounted height H1 13 mm includes the U 201 seat washer; the bearing alone is 11.4 mm high. reference speed 8,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 45 g. Capacity density: 13.3 kN C from 0.045 kg of bearing steel gives about 295.6 kN per kilogram; static density is correspondingly 462.2 kN/kg at C0 20.8 kN. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.0022 at the 11,000 r/min limiting speed raises the required axial preload to about 106 N; the reference-speed value 56 N is the thermal design point. Static-first selection data: 20.8 kN C0 spread across the 11.4 mm stack gives 1.8 kN of static rating per height millimetre, and the 45 g mass/C0 ratio is about 2 g per static kN — crane-hook and screw positions are normally sized on these two figures. Pitch-diameter arithmetic: dm = (12+28)/2 = 20.0 mm; at the 11,000 r/min limiting speed that corresponds to roughly 220k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Stack/annulus proportions: the 11.4 mm axial stack over the 503 mm² washer annulus gives 22.66 mm of height per annular square millimetre ×10⁻³, and at 45 g the bearing holds about 462.2 kN of C0 per kilogram. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53201 and U 201 are two order numbers shipping as two articles; the installed 13 mm H1 rather than 11.4 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "light screw jacks with deflecting screws",
      "conveyor take-up screw thrusts",
      "appliance gearboxes on lightly stressed seats"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "tilted running after a mismatched U washer leaves only a narrow band of spherical contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "track rust staining from condensate during long idle periods in humid plant air",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The shaft washer remains the tight, ground-bore component on the 12 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 201 into the register.",
      "Minimum axial load still applies with factor A 0.0022: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "The sphered housing washer of 53201 MUST run against the U 201 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "The 13.3/20.8 kN figures belong to 53201 specifically (the single sphered pressed steel execution of 53201); suffixed, sphered and counterpart-series order numbers are separate articles, and U 201 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53201?",
        "a": "The catalogue envelope is 12×28×11.4 mm plus the 1.6 mm the U 201 seat washer adds to reach H1 13 mm, mass 45 g; ratings C 13.3 kN / C0 20.8 kN / Pu 0.765 kN, reference speed 8,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53201 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 01: bore 12 mm for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "How much misalignment can 53201 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      },
      {
        "q": "What is the difference between H and H1?",
        "a": "H 11.4 mm is the height of the bearing itself; H1 13 mm is the installed height including the U 201 seat washer. Housing recesses and cover stacks must be drawn to H1, not H."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51201-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 12×28×11.4 mm ISO 104 thrust-ball envelope with catalogue ratings within 10 %; 51201 is the single-direction flat-seat, stamped sheet-steel cage execution of this size — boundary dimensions interchangeable, execution differs. Bearing heights match, but this sphered SKF execution additionally needs its U 201 seat washer and stands 13 mm (H1) when mounted."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53201",
      "53201 + U 201"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53202",
    "brand": "SKF",
    "manufacturer_designation": "53202",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 15,
    "D_mm": 32,
    "B_mm": 13.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 15.9,
    "static_load_kN": 25,
    "fatigue_load_limit_kN": 0.915,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 63,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53202 is SKF's 15 mm-bore single-direction thrust ball bearing in the 53200 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 15×32×13.3 mm U 202 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 02 encode the bore as 15 mm, the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 15×32×13.3 mm (0.591×1.26×0.524 in), 8.5 mm radial section, C 15.9 kN, C0 25 kN, Pu 0.915 kN. Mounted height H1 15 mm includes the U 202 seat washer; the bearing alone is 13.3 mm high. reference speed 7,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 63 g. Speed band width for this size is 3,000 r/min between reference and limiting (1.43× ratio); lubrication, preload and heat removal decide where inside that band 53202 can actually run. Washer-annulus check: the π/4·(D²−d²) contact annulus of 53202 covers about 628 mm², distributing C0 25 kN over a mean track circle of π·dm ≈ 74 mm. Capacity density: 15.9 kN C from 0.063 kg of bearing steel gives about 252.4 kN per kilogram; static density is correspondingly 396.8 kN/kg at C0 25 kN. Pitch-diameter arithmetic: dm = (15+32)/2 = 23.5 mm; at the 10,000 r/min limiting speed that corresponds to roughly 235k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Imperial cross-check for procurement drawings: 0.591 in bore, 1.26 in OD, 0.524 in height, and the 63 g catalogue mass converts to 0.063 kg (2.2 oz). Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 32 mm washer can tilt inside the U 202 seat; check the actual tilt allowance in the mounting drawing, since the 1.7 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "light screw jacks with deflecting screws",
      "appliance gearboxes on lightly stressed seats",
      "conveyor take-up screw thrusts"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "tilted running after a mismatched U washer leaves only a narrow band of spherical contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face"
    ],
    "pitfalls": [
      "The shaft washer remains the tight, ground-bore component on the 15 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 202 into the register.",
      "Minimum axial load still applies with factor A 0.0038: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The sphered housing washer of 53202 MUST run against the U 202 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 202 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "Ordering discipline for 53202: the catalogue page quotes 53202 plus U 202 and its 15.9/25 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53202?",
        "a": "53202 measures 15 mm bore × 32 mm OD × 13.3 mm bearing height (0.591 × 1.26 × 0.524 in), or 15 mm mounted H1 including the U 202 seat washer, mass about 63 g. SKF 17000 ratings: C 15.9 kN, C0 25 kN, Pu 0.915 kN, reference speed 7,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53202 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 02 encode the bore as 15 mm, the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53202 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53202",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53202",
      "53202 + U 202"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53203",
    "brand": "SKF",
    "manufacturer_designation": "53203",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 17,
    "D_mm": 35,
    "B_mm": 13.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 16.3,
    "static_load_kN": 27,
    "fatigue_load_limit_kN": 1,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 71,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53203 is an ISO 104 single-direction thrust ball bearing, 17 mm bore and 35 mm OD, with a sphered housing washer and U seat washer, standing 13.2 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 03: bore 17 mm for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 17×35×13.2 mm (0.669×1.378×0.52 in), 9.0 mm radial section, C 16.3 kN, C0 27 kN, Pu 1 kN. Mounted height H1 15 mm includes the U 203 seat washer; the bearing alone is 13.2 mm high. reference speed 6,700 r/min (thermal) and limiting speed 9,500 r/min (mechanical), catalogue mass 71 g. Light-load floor: Pu = 1 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 53203; the number is 6 % of the 16.3 kN dynamic rating. Minimum-load arithmetic: with dm ≈ 26.0 mm and factor A 0.0047, Fam ≈ A·(n·dm/1000)² at the 6,700 r/min reference speed is about 143 N for 53203; below that preload the balls skid and smear the tracks. Speed-ratio note for this exact unit: the reference speed is 6,700 r/min against a 9,500 r/min limiting speed, a reference-to-limit ratio of 0.71. Pitch-diameter arithmetic: dm = (17+35)/2 = 26.0 mm; at the 9,500 r/min limiting speed that corresponds to roughly 247k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Washer-annulus check: the π/4·(D²−d²) contact annulus of 53203 covers about 735 mm², distributing C0 27 kN over a mean track circle of π·dm ≈ 82 mm. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53203 and U 203 are two order numbers shipping as two articles; the installed 15 mm H1 rather than 13.2 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "appliance gearboxes on lightly stressed seats",
      "small vertical motor shafts with approximate housing alignment",
      "conveyor take-up screw thrusts"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 203 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "The sphered housing washer of 53203 MUST run against the U 203 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Minimum axial load still applies with factor A 0.0047: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "Ordering discipline for 53203: the catalogue page quotes 53203 plus U 203 and its 16.3/27 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53203?",
        "a": "The catalogue envelope is 17×35×13.2 mm plus the 1.8 mm the U 203 seat washer adds to reach H1 15 mm, mass 71 g; ratings C 16.3 kN / C0 27 kN / Pu 1 kN, reference speed 6,700 r/min (thermal) and limiting speed 9,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53203 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 03: bore 17 mm for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "How much misalignment can 53203 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      },
      {
        "q": "What is the difference between H and H1?",
        "a": "H 13.2 mm is the height of the bearing itself; H1 15 mm is the installed height including the U 203 seat washer. Housing recesses and cover stacks must be drawn to H1, not H."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53203",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53203",
      "53203 + U 203"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53204",
    "brand": "SKF",
    "manufacturer_designation": "53204",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 20,
    "D_mm": 40,
    "B_mm": 14.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 21.2,
    "static_load_kN": 37.5,
    "fatigue_load_limit_kN": 1.4,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 53200 series order number 53204 is a SKF single-direction thrust ball bearing for a 20 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 20×40×14.7 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 04 decodes to 20 mm (code 04 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 20×40×14.7 mm (0.787×1.575×0.579 in), 10.0 mm radial section, C 21.2 kN, C0 37.5 kN, Pu 1.4 kN. Mounted height H1 17 mm includes the U 204 seat washer; the bearing alone is 14.7 mm high. reference speed 5,600 r/min (thermal) and limiting speed 8,000 r/min (mechanical), catalogue mass 100 g. Static-first selection data: 37.5 kN C0 spread across the 14.7 mm stack gives 2.6 kN of static rating per height millimetre, and the 100 g mass/C0 ratio is about 3 g per static kN — crane-hook and screw positions are normally sized on these two figures. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 8,000 r/min while thermal balance under catalogue load sets the 5,600 r/min reference; at dm ≈ 30.0 mm the corresponding dn is approximately 240k mm·r/min. At the printed limiting speed of 8,000 r/min the mean pitch diameter dm ≈ 30.0 mm implies a dn value around 240k mm·r/min; the 5,600 r/min reference speed is the thermal-planning value under catalogue load. Minimum-load arithmetic: with dm ≈ 30.0 mm and factor A 0.0085, Fam ≈ A·(n·dm/1000)² at the 5,600 r/min reference speed is about 240 N for 53204; below that preload the balls skid and smear the tracks. Imperial cross-check for procurement drawings: 0.787 in bore, 1.575 in OD, 0.579 in height, and the 100 g catalogue mass converts to 0.100 kg (3.5 oz). Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53204 and U 204 are two order numbers shipping as two articles; the installed 17 mm H1 rather than 14.7 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "appliance gearboxes on lightly stressed seats",
      "small vertical motor shafts with approximate housing alignment",
      "agricultural adjustment pivots"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "edge loading on the ball set when the U seat washer is fitted with its concave face reversed",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Minimum axial load still applies with factor A 0.0085: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 204 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "The 21.2/37.5 kN figures belong to 53204 specifically (the single sphered pressed steel execution of 53204); suffixed, sphered and counterpart-series order numbers are separate articles, and U 204 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53204?",
        "a": "Boundary dimensions to ISO 104: bore 20 mm, OD 40 mm, height 14.7 mm (H1 17 mm installed with the U 204 seat washer); weight 100 g. Load figures from SKF 17000: dynamic 21.2 kN, static 37.5 kN, fatigue limit 1.4 kN; reference speed 5,600 r/min (thermal) and limiting speed 8,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53204 mean?",
        "a": "the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 04 decodes to 20 mm (code 04 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "What is the difference between H and H1?",
        "a": "H 14.7 mm is the height of the bearing itself; H1 17 mm is the installed height including the U 204 seat washer. Housing recesses and cover stacks must be drawn to H1, not H."
      },
      {
        "q": "Why does 53204 need a U 204 seat washer?",
        "a": "The housing washer of 53204 has a sphered back face. The U 204 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53204",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53204",
      "53204 + U 204"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53205",
    "brand": "SKF",
    "manufacturer_designation": "53205",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 47,
    "B_mm": 16.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 50,
    "fatigue_load_limit_kN": 1.86,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53205 is an ISO 104 single-direction thrust ball bearing, 25 mm bore and 47 mm OD, with a sphered housing washer and U seat washer, standing 16.7 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 05: bore 25 mm (code 05 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 25×47×16.7 mm (0.984×1.85×0.657 in), 11.0 mm radial section, C 26.5 kN, C0 50 kN, Pu 1.86 kN. Mounted height H1 19 mm includes the U 205 seat washer; the bearing alone is 16.7 mm high. reference speed 5,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), catalogue mass 150 g. Static-first selection data: 50 kN C0 spread across the 16.7 mm stack gives 3.0 kN of static rating per height millimetre, and the 150 g mass/C0 ratio is about 3 g per static kN — crane-hook and screw positions are normally sized on these two figures. Load balance: C0 50 kN against C 26.5 kN gives a 1.89 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 1.86 kN enters the adjusted-life check. Speed band width for this size is 2,000 r/min between reference and limiting (1.40× ratio); lubrication, preload and heat removal decide where inside that band 53205 can actually run. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.015 at the 7,000 r/min limiting speed raises the required axial preload to about 953 N; the reference-speed value 486 N is the thermal design point. Pitch-diameter arithmetic: dm = (25+47)/2 = 36.0 mm; at the 7,000 r/min limiting speed that corresponds to roughly 252k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 47 mm washer can tilt inside the U 205 seat; check the actual tilt allowance in the mounting drawing, since the 2.3 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "vertical pumps with shaft-to-housing misalignment",
      "crane hooks whose block deflects under offset lifts",
      "machine-tool supports on less rigid fabricated housings"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "edge loading on the ball set when the U seat washer is fitted with its concave face reversed",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Replacement orders must list both 53205 and U 205: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 50 kN static-rated set.",
      "Dimension the housing to the 19 mm mounted height H1 (bearing plus U 205), not the 16.7 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The shaft washer remains the tight, ground-bore component on the 25 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 205 into the register.",
      "Minimum axial load still applies with factor A 0.015: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "Ordering discipline for 53205: the catalogue page quotes 53205 plus U 205 and its 26.5/50 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53205?",
        "a": "The catalogue envelope is 25×47×16.7 mm plus the 2.3 mm the U 205 seat washer adds to reach H1 19 mm, mass 150 g; ratings C 26.5 kN / C0 50 kN / Pu 1.86 kN, reference speed 5,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53205 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 05: bore 25 mm (code 05 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "How much misalignment can 53205 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      },
      {
        "q": "What is the difference between H and H1?",
        "a": "H 16.7 mm is the height of the bearing itself; H1 19 mm is the installed height including the U 205 seat washer. Housing recesses and cover stacks must be drawn to H1, not H."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53205",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53205",
      "53205 + U 205"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53206",
    "brand": "SKF",
    "manufacturer_designation": "53206",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 52,
    "B_mm": 17.8,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 25.1,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 1.86,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53206 is SKF's 30 mm-bore single-direction thrust ball bearing in the 53200 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 30×52×17.8 mm U 206 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 06 encode the bore as 30 mm (code 06 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 30×52×17.8 mm (1.181×2.047×0.701 in), 11.0 mm radial section, C 25.1 kN, C0 51 kN, Pu 1.86 kN. Mounted height H1 20 mm includes the U 206 seat washer; the bearing alone is 17.8 mm high. reference speed 4,500 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 180 g. Load balance: C0 51 kN against C 25.1 kN gives a 2.03 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 1.86 kN enters the adjusted-life check. Washer-annulus check: the π/4·(D²−d²) contact annulus of 53206 covers about 1,417 mm², distributing C0 51 kN over a mean track circle of π·dm ≈ 129 mm. Light-load floor: Pu = 1.86 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 53206; the number is 7 % of the 25.1 kN dynamic rating. Sizing arithmetic on the 30 mm bore: 25.1 kN C over the 11.0 mm radial section gives 2.3 kN per section millimetre, and the 17.8 mm stack height is 1.62× that section — proportions typical of a 53200 thrust section. Track-circle loading: per millimetre of mean track circumference the 25.1 kN dynamic rating corresponds to roughly 0.19 kN/mm of π·dm track, a useful comparison against the other dimension series of the 30 mm bore. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 52 mm washer can tilt inside the U 206 seat; check the actual tilt allowance in the mounting drawing, since the 2.2 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "agricultural and construction-machine pivots",
      "machine-tool supports on less rigid fabricated housings",
      "vertical pumps with shaft-to-housing misalignment"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "washer face scoring from swarf trapped between the loose housing washer and its register"
    ],
    "pitfalls": [
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 206 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "Dimension the housing to the 20 mm mounted height H1 (bearing plus U 206), not the 17.8 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "Minimum axial load still applies with factor A 0.013: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53206 as the single sphered pressed steel execution; other order numbers of the 53206 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 206 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53206?",
        "a": "53206 measures 30 mm bore × 52 mm OD × 17.8 mm bearing height (1.181 × 2.047 × 0.701 in), or 20 mm mounted H1 including the U 206 seat washer, mass about 180 g. SKF 17000 ratings: C 25.1 kN, C0 51 kN, Pu 1.86 kN, reference speed 4,500 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53206 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 06 encode the bore as 30 mm (code 06 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53206 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53206",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53206",
      "53206 + U 206"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53306",
    "brand": "SKF",
    "manufacturer_designation": "53306",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 60,
    "B_mm": 22.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 35.8,
    "static_load_kN": 65.5,
    "fatigue_load_limit_kN": 2.4,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 330,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53306 is SKF's 30 mm-bore single-direction thrust ball bearing in the 53300 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 30×60×22.6 mm U 306 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 06 encode the bore as 30 mm (code 06 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 30×60×22.6 mm (1.181×2.362×0.89 in), 15.0 mm radial section, C 35.8 kN, C0 65.5 kN, Pu 2.4 kN. Mounted height H1 25 mm includes the U 306 seat washer; the bearing alone is 22.6 mm high. reference speed 3,800 r/min (thermal) and limiting speed 5,300 r/min (mechanical), catalogue mass 330 g. Speed band width for this size is 1,500 r/min between reference and limiting (1.39× ratio); lubrication, preload and heat removal decide where inside that band 53306 can actually run. Mass and section check: 330 g inside the 30×60×22.6 mm outline leaves a 15.0 mm radial section, and the 65.5 kN static rating is 1.83× the dynamic rating — plan static safety and minimum preload against those figures. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 5,300 r/min while thermal balance under catalogue load sets the 3,800 r/min reference; at dm ≈ 45.0 mm the corresponding dn is approximately 239k mm·r/min. Stack/annulus proportions: the 22.6 mm axial stack over the 2,121 mm² washer annulus gives 10.66 mm of height per annular square millimetre ×10⁻³, and at 330 g the bearing holds about 198.5 kN of C0 per kilogram. Pitch-diameter arithmetic: dm = (30+60)/2 = 45.0 mm; at the 5,300 r/min limiting speed that corresponds to roughly 239k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53306 and U 306 are two order numbers shipping as two articles; the installed 25 mm H1 rather than 22.6 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "vertical pumps with shaft-to-housing misalignment",
      "screw-jack spindles that bend under load",
      "crane hooks whose block deflects under offset lifts"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "tilted running after a mismatched U washer leaves only a narrow band of spherical contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Replacement orders must list both 53306 and U 306: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 65.5 kN static-rated set.",
      "Minimum axial load still applies with factor A 0.026: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The shaft washer remains the tight, ground-bore component on the 30 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 306 into the register.",
      "Ordering discipline for 53306: the catalogue page quotes 53306 plus U 306 and its 35.8/65.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53306?",
        "a": "53306 measures 30 mm bore × 60 mm OD × 22.6 mm bearing height (1.181 × 2.362 × 0.89 in), or 25 mm mounted H1 including the U 306 seat washer, mass about 330 g. SKF 17000 ratings: C 35.8 kN, C0 65.5 kN, Pu 2.4 kN, reference speed 3,800 r/min (thermal) and limiting speed 5,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53306 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 06 encode the bore as 30 mm (code 06 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Why does 53306 need a U 306 seat washer?",
        "a": "The housing washer of 53306 has a sphered back face. The U 306 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      },
      {
        "q": "Is the U 306 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53306 and U 306 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53306",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53306",
      "53306 + U 306"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53207",
    "brand": "SKF",
    "manufacturer_designation": "53207",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 62,
    "B_mm": 19.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 35.1,
    "static_load_kN": 73.5,
    "fatigue_load_limit_kN": 2.7,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 280,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 53200 series order number 53207 is a SKF single-direction thrust ball bearing for a 35 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 35×62×19.9 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 07 decodes to 35 mm (code 07 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 35×62×19.9 mm (1.378×2.441×0.783 in), 13.5 mm radial section, C 35.1 kN, C0 73.5 kN, Pu 2.7 kN. Mounted height H1 22 mm includes the U 207 seat washer; the bearing alone is 19.9 mm high. reference speed 4,000 r/min (thermal) and limiting speed 5,600 r/min (mechanical), catalogue mass 280 g. Pitch-diameter arithmetic: dm = (35+62)/2 = 48.5 mm; at the 5,600 r/min limiting speed that corresponds to roughly 272k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Envelope economics: the 19.9 mm axial height over a 13.5 mm radial section yields 1.8 kN of dynamic capacity per height millimetre, and the bearing weighs 280 g for 35.1 kN C — about 8 g per rated kN. Sizing arithmetic on the 35 mm bore: 35.1 kN C over the 13.5 mm radial section gives 2.6 kN per section millimetre, and the 19.9 mm stack height is 1.47× that section — proportions typical of a 53200 thrust section. Mass and section check: 280 g inside the 35×62×19.9 mm outline leaves a 13.5 mm radial section, and the 73.5 kN static rating is 2.09× the dynamic rating — plan static safety and minimum preload against those figures. Bore-to-OD planning: OD 62 over bore 35 is a 1.77× step for this size, and the 19.9 mm height gives a bore/height ratio of 1.76; use these ratios when the housing recess around the 35 mm shaft is the first constraint. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53207 and U 207 are two order numbers shipping as two articles; the installed 22 mm H1 rather than 19.9 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "agricultural and construction-machine pivots",
      "vertical pumps with shaft-to-housing misalignment",
      "machine-tool supports on less rigid fabricated housings"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "track rust staining from condensate during long idle periods in humid plant air",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The shaft washer remains the tight, ground-bore component on the 35 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 207 into the register.",
      "Minimum axial load still applies with factor A 0.028: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The sphered housing washer of 53207 MUST run against the U 207 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 207 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53207 as the single sphered pressed steel execution; other order numbers of the 53207 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 207 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53207?",
        "a": "Boundary dimensions to ISO 104: bore 35 mm, OD 62 mm, height 19.9 mm (H1 22 mm installed with the U 207 seat washer); weight 280 g. Load figures from SKF 17000: dynamic 35.1 kN, static 73.5 kN, fatigue limit 2.7 kN; reference speed 4,000 r/min (thermal) and limiting speed 5,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53207 mean?",
        "a": "the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 07 decodes to 35 mm (code 07 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is 53207 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53207",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53207",
      "53207 + U 207"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53307",
    "brand": "SKF",
    "manufacturer_designation": "53307",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 68,
    "B_mm": 25.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 49.4,
    "static_load_kN": 96.5,
    "fatigue_load_limit_kN": 3.55,
    "reference_speed_rpm": 3200,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 460,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53307 is an ISO 104 single-direction thrust ball bearing, 35 mm bore and 68 mm OD, with a sphered housing washer and U seat washer, standing 25.6 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 07: bore 35 mm (code 07 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 35×68×25.6 mm (1.378×2.677×1.008 in), 16.5 mm radial section, C 49.4 kN, C0 96.5 kN, Pu 3.55 kN. Mounted height H1 28 mm includes the U 307 seat washer; the bearing alone is 25.6 mm high. reference speed 3,200 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 460 g. Minimum-load arithmetic: with dm ≈ 51.5 mm and factor A 0.048, Fam ≈ A·(n·dm/1000)² at the 3,200 r/min reference speed is about 1.3 kN for 53307; below that preload the balls skid and smear the tracks. Static-first selection data: 96.5 kN C0 spread across the 25.6 mm stack gives 3.8 kN of static rating per height millimetre, and the 460 g mass/C0 ratio is about 5 g per static kN — crane-hook and screw positions are normally sized on these two figures. Pitch-diameter arithmetic: dm = (35+68)/2 = 51.5 mm; at the 4,500 r/min limiting speed that corresponds to roughly 232k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Track-circle loading: per millimetre of mean track circumference the 49.4 kN dynamic rating corresponds to roughly 0.31 kN/mm of π·dm track, a useful comparison against the other dimension series of the 35 mm bore. Washer-stack proportions: the U 307 seat washer adds 2.4 mm to the 25.6 mm bearing height for a mounted H1 of 28 mm, while the 16.5 mm radial section against 35 mm bore (section/bore ≈ 0.47) identifies the envelope. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 68 mm washer can tilt inside the U 307 seat; check the actual tilt allowance in the mounting drawing, since the 2.4 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "machine-tool supports on less rigid fabricated housings",
      "vertical pumps with shaft-to-housing misalignment",
      "crane hooks whose block deflects under offset lifts"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "tilted running after a mismatched U washer leaves only a narrow band of spherical contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 307 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "Dimension the housing to the 28 mm mounted height H1 (bearing plus U 307), not the 25.6 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "Minimum axial load still applies with factor A 0.048: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The 49.4/96.5 kN figures belong to 53307 specifically (the single sphered pressed steel execution of 53307); suffixed, sphered and counterpart-series order numbers are separate articles, and U 307 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53307?",
        "a": "The catalogue envelope is 35×68×25.6 mm plus the 2.4 mm the U 307 seat washer adds to reach H1 28 mm, mass 460 g; ratings C 49.4 kN / C0 96.5 kN / Pu 3.55 kN, reference speed 3,200 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53307 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 07: bore 35 mm (code 07 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is the U 307 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53307 and U 307 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      },
      {
        "q": "Is 53307 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53307",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53307",
      "53307 + U 307"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53208",
    "brand": "SKF",
    "manufacturer_designation": "53208",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 68,
    "B_mm": 20.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 44.2,
    "static_load_kN": 96.5,
    "fatigue_load_limit_kN": 3.6,
    "reference_speed_rpm": 3600,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53208 is SKF's 40 mm-bore single-direction thrust ball bearing in the 53200 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 40×68×20.3 mm U 208 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 08 encode the bore as 40 mm (code 08 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 40×68×20.3 mm (1.575×2.677×0.799 in), 14.0 mm radial section, C 44.2 kN, C0 96.5 kN, Pu 3.6 kN. Mounted height H1 23 mm includes the U 208 seat washer; the bearing alone is 20.3 mm high. reference speed 3,600 r/min (thermal) and limiting speed 5,300 r/min (mechanical), catalogue mass 350 g. Capacity density: 44.2 kN C from 0.350 kg of bearing steel gives about 126.3 kN per kilogram; static density is correspondingly 275.7 kN/kg at C0 96.5 kN. At the printed limiting speed of 5,300 r/min the mean pitch diameter dm ≈ 54.0 mm implies a dn value around 286k mm·r/min; the 3,600 r/min reference speed is the thermal-planning value under catalogue load. Load balance: C0 96.5 kN against C 44.2 kN gives a 2.18 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 3.6 kN enters the adjusted-life check. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.058 at the 5,300 r/min limiting speed raises the required axial preload to about 4.8 kN; the reference-speed value 2.2 kN is the thermal design point. Static-first selection data: 96.5 kN C0 spread across the 20.3 mm stack gives 4.8 kN of static rating per height millimetre, and the 350 g mass/C0 ratio is about 4 g per static kN — crane-hook and screw positions are normally sized on these two figures. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 68 mm washer can tilt inside the U 208 seat; check the actual tilt allowance in the mounting drawing, since the 2.7 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "vertical pumps with shaft-to-housing misalignment",
      "crane hooks whose block deflects under offset lifts",
      "screw-jack spindles that bend under load"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "tilted running after a mismatched U washer leaves only a narrow band of spherical contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Replacement orders must list both 53208 and U 208: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 96.5 kN static-rated set.",
      "Minimum axial load still applies with factor A 0.058: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The shaft washer remains the tight, ground-bore component on the 40 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 208 into the register.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53208 as the single sphered pressed steel execution; other order numbers of the 53208 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 208 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53208?",
        "a": "53208 measures 40 mm bore × 68 mm OD × 20.3 mm bearing height (1.575 × 2.677 × 0.799 in), or 23 mm mounted H1 including the U 208 seat washer, mass about 350 g. SKF 17000 ratings: C 44.2 kN, C0 96.5 kN, Pu 3.6 kN, reference speed 3,600 r/min (thermal) and limiting speed 5,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53208 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 08 encode the bore as 40 mm (code 08 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53208 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53208",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53208",
      "53208 + U 208"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53308",
    "brand": "SKF",
    "manufacturer_designation": "53308",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 78,
    "B_mm": 28.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 61.8,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 670,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53308 is SKF's 40 mm-bore single-direction thrust ball bearing in the 53300 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 40×78×28.5 mm U 308 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 08 encode the bore as 40 mm (code 08 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 40×78×28.5 mm (1.575×3.071×1.122 in), 19.0 mm radial section, C 61.8 kN, C0 122 kN, Pu 4.5 kN. Mounted height H1 31 mm includes the U 308 seat washer; the bearing alone is 28.5 mm high. reference speed 2,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 670 g. Envelope economics: the 28.5 mm axial height over a 19.0 mm radial section yields 2.2 kN of dynamic capacity per height millimetre, and the bearing weighs 670 g for 61.8 kN C — about 11 g per rated kN. Stack/annulus proportions: the 28.5 mm axial stack over the 3,522 mm² washer annulus gives 8.09 mm of height per annular square millimetre ×10⁻³, and at 670 g the bearing holds about 182.1 kN of C0 per kilogram. Load balance: C0 122 kN against C 61.8 kN gives a 1.97 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 4.5 kN enters the adjusted-life check. Capacity density: 61.8 kN C from 0.670 kg of bearing steel gives about 92.2 kN per kilogram; static density is correspondingly 182.1 kN/kg at C0 122 kN. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.077 at the 4,000 r/min limiting speed raises the required axial preload to about 4.3 kN; the reference-speed value 2.1 kN is the thermal design point. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 78 mm washer can tilt inside the U 308 seat; check the actual tilt allowance in the mounting drawing, since the 2.5 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "agricultural and construction-machine pivots",
      "crane hooks whose block deflects under offset lifts",
      "machine-tool supports on less rigid fabricated housings"
    ],
    "failure_modes": [
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "fretting corrosion in the spherical interface under oscillation with no grease between washer and seat",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "track rust staining from condensate during long idle periods in humid plant air",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Minimum axial load still applies with factor A 0.077: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 308 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The 61.8/122 kN figures belong to 53308 specifically (the single sphered pressed steel execution of 53308); suffixed, sphered and counterpart-series order numbers are separate articles, and U 308 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53308?",
        "a": "53308 measures 40 mm bore × 78 mm OD × 28.5 mm bearing height (1.575 × 3.071 × 1.122 in), or 31 mm mounted H1 including the U 308 seat washer, mass about 670 g. SKF 17000 ratings: C 61.8 kN, C0 122 kN, Pu 4.5 kN, reference speed 2,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53308 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 08 encode the bore as 40 mm (code 08 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Why does 53308 need a U 308 seat washer?",
        "a": "The housing washer of 53308 has a sphered back face. The U 308 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      },
      {
        "q": "Is the U 308 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53308 and U 308 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53308",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53308",
      "53308 + U 308"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53408",
    "brand": "SKF",
    "manufacturer_designation": "53408",
    "series": "53400-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 38.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 95.6,
    "static_load_kN": 183,
    "fatigue_load_limit_kN": 6.8,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 1350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53408 is SKF's 40 mm-bore single-direction thrust ball bearing in the 53400 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 40×90×38.2 mm U 408 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 08 encode the bore as 40 mm (code 08 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 40×90×38.2 mm (1.575×3.543×1.504 in), 25.0 mm radial section, C 95.6 kN, C0 183 kN, Pu 6.8 kN. Mounted height H1 42 mm includes the U 408 seat washer; the bearing alone is 38.2 mm high. reference speed 2,400 r/min (thermal) and limiting speed 3,200 r/min (mechanical), catalogue mass 1350 g. Imperial cross-check for procurement drawings: 1.575 in bore, 3.543 in OD, 1.504 in height, and the 1350 g catalogue mass converts to 1.350 kg (47.6 oz). Envelope economics: the 38.2 mm axial height over a 25.0 mm radial section yields 2.5 kN of dynamic capacity per height millimetre, and the bearing weighs 1350 g for 95.6 kN C — about 14 g per rated kN. Sizing arithmetic on the 40 mm bore: 95.6 kN C over the 25.0 mm radial section gives 3.8 kN per section millimetre, and the 38.2 mm stack height is 1.53× that section — proportions typical of a 53400 thrust section. Selection figures for 53408: the C0/C ratio is 1.91, Pu 6.8 kN is about 7 % of C, and the catalogue mass works out to roughly 34 g per millimetre of bore; the printed minimum-load factor is A 0.26. Mass and section check: 1350 g inside the 40×90×38.2 mm outline leaves a 25.0 mm radial section, and the 183 kN static rating is 1.91× the dynamic rating — plan static safety and minimum preload against those figures. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53408 and U 408 are two order numbers shipping as two articles; the installed 42 mm H1 rather than 38.2 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "crane hooks whose block deflects under offset lifts",
      "agricultural and construction-machine pivots",
      "vertical pumps with shaft-to-housing misalignment"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "corrosion lock of the spherical pair during long outdoor idleness with no preservative grease",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The sphered housing washer of 53408 MUST run against the U 408 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 408 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "Dimension the housing to the 42 mm mounted height H1 (bearing plus U 408), not the 38.2 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53408 as the single sphered pressed steel execution; other order numbers of the 53408 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 408 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53408?",
        "a": "53408 measures 40 mm bore × 90 mm OD × 38.2 mm bearing height (1.575 × 3.543 × 1.504 in), or 42 mm mounted H1 including the U 408 seat washer, mass about 1350 g. SKF 17000 ratings: C 95.6 kN, C0 183 kN, Pu 6.8 kN, reference speed 2,400 r/min (thermal) and limiting speed 3,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53408 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 08 encode the bore as 40 mm (code 08 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53408 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53408",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53408",
      "53408 + U 408"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53209",
    "brand": "SKF",
    "manufacturer_designation": "53209",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 73,
    "B_mm": 21.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 39,
    "static_load_kN": 86.5,
    "fatigue_load_limit_kN": 3.2,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 390,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 53200 series order number 53209 is a SKF single-direction thrust ball bearing for a 45 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 45×73×21.3 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 09 decodes to 45 mm (code 09 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 45×73×21.3 mm (1.772×2.874×0.839 in), 14.0 mm radial section, C 39 kN, C0 86.5 kN, Pu 3.2 kN. Mounted height H1 24 mm includes the U 209 seat washer; the bearing alone is 21.3 mm high. reference speed 3,400 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 390 g. Mass and section check: 390 g inside the 45×73×21.3 mm outline leaves a 14.0 mm radial section, and the 86.5 kN static rating is 2.22× the dynamic rating — plan static safety and minimum preload against those figures. Capacity density: 39 kN C from 0.390 kg of bearing steel gives about 100.0 kN per kilogram; static density is correspondingly 221.8 kN/kg at C0 86.5 kN. At the printed limiting speed of 4,800 r/min the mean pitch diameter dm ≈ 59.0 mm implies a dn value around 283k mm·r/min; the 3,400 r/min reference speed is the thermal-planning value under catalogue load. Sizing arithmetic on the 45 mm bore: 39 kN C over the 14.0 mm radial section gives 2.8 kN per section millimetre, and the 21.3 mm stack height is 1.52× that section — proportions typical of a 53200 thrust section. Rating split for documentation: dynamic 39 kN (L10 life), static 86.5 kN (safety factor s0), fatigue limit 3.2 kN (adjusted life) — three different uses of three different numbers for 53209, none interchangeable with another. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53209 and U 209 are two order numbers shipping as two articles; the installed 24 mm H1 rather than 21.3 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "machine-tool supports on less rigid fabricated housings",
      "crane hooks whose block deflects under offset lifts",
      "vertical pumps with shaft-to-housing misalignment"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Replacement orders must list both 53209 and U 209: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 86.5 kN static-rated set.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "Minimum axial load still applies with factor A 0.038: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The 39/86.5 kN figures belong to 53209 specifically (the single sphered pressed steel execution of 53209); suffixed, sphered and counterpart-series order numbers are separate articles, and U 209 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53209?",
        "a": "Boundary dimensions to ISO 104: bore 45 mm, OD 73 mm, height 21.3 mm (H1 24 mm installed with the U 209 seat washer); weight 390 g. Load figures from SKF 17000: dynamic 39 kN, static 86.5 kN, fatigue limit 3.2 kN; reference speed 3,400 r/min (thermal) and limiting speed 4,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53209 mean?",
        "a": "the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 09 decodes to 45 mm (code 09 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is 53209 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53209",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53209",
      "53209 + U 209"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53309",
    "brand": "SKF",
    "manufacturer_designation": "53309",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 30.1,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 76.1,
    "static_load_kN": 153,
    "fatigue_load_limit_kN": 5.6,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 830,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53309 is an ISO 104 single-direction thrust ball bearing, 45 mm bore and 85 mm OD, with a sphered housing washer and U seat washer, standing 30.1 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 09: bore 45 mm (code 09 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 45×85×30.1 mm (1.772×3.346×1.185 in), 20.0 mm radial section, C 76.1 kN, C0 153 kN, Pu 5.6 kN. Mounted height H1 33 mm includes the U 309 seat washer; the bearing alone is 30.1 mm high. reference speed 2,600 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 830 g. Light-load floor: Pu = 5.6 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 53309; the number is 7 % of the 76.1 kN dynamic rating. Bore-to-OD planning: OD 85 over bore 45 is a 1.89× step for this size, and the 30.1 mm height gives a bore/height ratio of 1.50; use these ratios when the housing recess around the 45 mm shaft is the first constraint. Pitch-diameter arithmetic: dm = (45+85)/2 = 65.0 mm; at the 3,800 r/min limiting speed that corresponds to roughly 247k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Sizing arithmetic on the 45 mm bore: 76.1 kN C over the 20.0 mm radial section gives 3.8 kN per section millimetre, and the 30.1 mm stack height is 1.51× that section — proportions typical of a 53300 thrust section. Speed-ratio note for this exact unit: the reference speed is 2,600 r/min against a 3,800 r/min limiting speed, a reference-to-limit ratio of 0.68. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 85 mm washer can tilt inside the U 309 seat; check the actual tilt allowance in the mounting drawing, since the 2.9 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "crane hooks whose block deflects under offset lifts",
      "agricultural and construction-machine pivots",
      "machine-tool supports on less rigid fabricated housings"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "tilted running after a mismatched U washer leaves only a narrow band of spherical contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "washer face scoring from swarf trapped between the loose housing washer and its register"
    ],
    "pitfalls": [
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 309 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Minimum axial load still applies with factor A 0.12: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The 76.1/153 kN figures belong to 53309 specifically (the single sphered pressed steel execution of 53309); suffixed, sphered and counterpart-series order numbers are separate articles, and U 309 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53309?",
        "a": "The catalogue envelope is 45×85×30.1 mm plus the 2.9 mm the U 309 seat washer adds to reach H1 33 mm, mass 830 g; ratings C 76.1 kN / C0 153 kN / Pu 5.6 kN, reference speed 2,600 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53309 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 09: bore 45 mm (code 09 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is the U 309 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53309 and U 309 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      },
      {
        "q": "Is 53309 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53309",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53309",
      "53309 + U 309"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53210",
    "brand": "SKF",
    "manufacturer_designation": "53210",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 78,
    "B_mm": 23.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 49.4,
    "static_load_kN": 116,
    "fatigue_load_limit_kN": 4.3,
    "reference_speed_rpm": 3200,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 470,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53210 is SKF's 50 mm-bore single-direction thrust ball bearing in the 53200 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 50×78×23.5 mm U 210 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 10 encode the bore as 50 mm (code 10 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 50×78×23.5 mm (1.969×3.071×0.925 in), 14.0 mm radial section, C 49.4 kN, C0 116 kN, Pu 4.3 kN. Mounted height H1 26 mm includes the U 210 seat washer; the bearing alone is 23.5 mm high. reference speed 3,200 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 470 g. Speed-ratio note for this exact unit: the reference speed is 3,200 r/min against a 4,500 r/min limiting speed, a reference-to-limit ratio of 0.71. Stack/annulus proportions: the 23.5 mm axial stack over the 2,815 mm² washer annulus gives 8.35 mm of height per annular square millimetre ×10⁻³, and at 470 g the bearing holds about 246.8 kN of C0 per kilogram. Capacity density: 49.4 kN C from 0.470 kg of bearing steel gives about 105.1 kN per kilogram; static density is correspondingly 246.8 kN/kg at C0 116 kN. Rating split for documentation: dynamic 49.4 kN (L10 life), static 116 kN (safety factor s0), fatigue limit 4.3 kN (adjusted life) — three different uses of three different numbers for 53210, none interchangeable with another. Selection figures for 53210: the C0/C ratio is 2.35, Pu 4.3 kN is about 9 % of C, and the catalogue mass works out to roughly 9 g per millimetre of bore; the printed minimum-load factor is A 0.069. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 78 mm washer can tilt inside the U 210 seat; check the actual tilt allowance in the mounting drawing, since the 2.5 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "crane hooks whose block deflects under offset lifts",
      "screw-jack spindles that bend under load",
      "vertical pumps with shaft-to-housing misalignment"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "edge loading on the ball set when the U seat washer is fitted with its concave face reversed",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The sphered housing washer of 53210 MUST run against the U 210 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 210 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53210 as the single sphered pressed steel execution; other order numbers of the 53210 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 210 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53210?",
        "a": "53210 measures 50 mm bore × 78 mm OD × 23.5 mm bearing height (1.969 × 3.071 × 0.925 in), or 26 mm mounted H1 including the U 210 seat washer, mass about 470 g. SKF 17000 ratings: C 49.4 kN, C0 116 kN, Pu 4.3 kN, reference speed 3,200 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53210 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 10 encode the bore as 50 mm (code 10 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Why does 53210 need a U 210 seat washer?",
        "a": "The housing washer of 53210 has a sphered back face. The U 210 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      },
      {
        "q": "Is the U 210 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53210 and U 210 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53210",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53210",
      "53210 + U 210"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53310",
    "brand": "SKF",
    "manufacturer_designation": "53310",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 95,
    "B_mm": 34.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 81.9,
    "static_load_kN": 170,
    "fatigue_load_limit_kN": 6.3,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53310 is an ISO 104 single-direction thrust ball bearing, 50 mm bore and 95 mm OD, with a sphered housing washer and U seat washer, standing 34.3 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 10: bore 50 mm (code 10 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 50×95×34.3 mm (1.969×3.74×1.35 in), 22.5 mm radial section, C 81.9 kN, C0 170 kN, Pu 6.3 kN. Mounted height H1 37 mm includes the U 310 seat washer; the bearing alone is 34.3 mm high. reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 1200 g. Imperial cross-check for procurement drawings: 1.969 in bore, 3.74 in OD, 1.35 in height, and the 1200 g catalogue mass converts to 1.200 kg (42.3 oz). Envelope economics: the 34.3 mm axial height over a 22.5 mm radial section yields 2.4 kN of dynamic capacity per height millimetre, and the bearing weighs 1200 g for 81.9 kN C — about 15 g per rated kN. Bore-to-OD planning: OD 95 over bore 50 is a 1.90× step for this size, and the 34.3 mm height gives a bore/height ratio of 1.46; use these ratios when the housing recess around the 50 mm shaft is the first constraint. Minimum-load arithmetic: with dm ≈ 72.5 mm and factor A 0.19, Fam ≈ A·(n·dm/1000)² at the 2,400 r/min reference speed is about 5.8 kN for 53310; below that preload the balls skid and smear the tracks. Light-load floor: Pu = 6.3 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 53310; the number is 8 % of the 81.9 kN dynamic rating. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53310 and U 310 are two order numbers shipping as two articles; the installed 37 mm H1 rather than 34.3 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "crane hooks whose block deflects under offset lifts",
      "machine-tool supports on less rigid fabricated housings",
      "agricultural and construction-machine pivots"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "corrosion lock of the spherical pair during long outdoor idleness with no preservative grease",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "The sphered housing washer of 53310 MUST run against the U 310 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 310 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "Dimension the housing to the 37 mm mounted height H1 (bearing plus U 310), not the 34.3 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53310 as the single sphered pressed steel execution; other order numbers of the 53310 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 310 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53310?",
        "a": "The catalogue envelope is 50×95×34.3 mm plus the 2.7 mm the U 310 seat washer adds to reach H1 37 mm, mass 1200 g; ratings C 81.9 kN / C0 170 kN / Pu 6.3 kN, reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53310 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 10: bore 50 mm (code 10 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is the U 310 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53310 and U 310 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      },
      {
        "q": "Is 53310 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53310",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53310",
      "53310 + U 310"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53410",
    "brand": "SKF",
    "manufacturer_designation": "53410",
    "series": "53400-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 45.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 159,
    "static_load_kN": 340,
    "fatigue_load_limit_kN": 12.5,
    "reference_speed_rpm": 1900,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 2300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53410 is SKF's 50 mm-bore single-direction thrust ball bearing in the 53400 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 50×110×45.6 mm U 410 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 10 encode the bore as 50 mm (code 10 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 50×110×45.6 mm (1.969×4.331×1.795 in), 30.0 mm radial section, C 159 kN, C0 340 kN, Pu 12.5 kN. Mounted height H1 50 mm includes the U 410 seat washer; the bearing alone is 45.6 mm high. reference speed 1,900 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 2300 g. Light-load floor: Pu = 12.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 53410; the number is 8 % of the 159 kN dynamic rating. Pitch-diameter arithmetic: dm = (50+110)/2 = 80.0 mm; at the 2,600 r/min limiting speed that corresponds to roughly 208k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Bore-to-OD planning: OD 110 over bore 50 is a 2.20× step for this size, and the 45.6 mm height gives a bore/height ratio of 1.10; use these ratios when the housing recess around the 50 mm shaft is the first constraint. Load balance: C0 340 kN against C 159 kN gives a 2.14 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 12.5 kN enters the adjusted-life check. Sizing arithmetic on the 50 mm bore: 159 kN C over the 30.0 mm radial section gives 5.3 kN per section millimetre, and the 45.6 mm stack height is 1.52× that section — proportions typical of a 53400 thrust section. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53410 and U 410 are two order numbers shipping as two articles; the installed 50 mm H1 rather than 45.6 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "agricultural and construction-machine pivots",
      "screw-jack spindles that bend under load",
      "crane hooks whose block deflects under offset lifts"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Dimension the housing to the 50 mm mounted height H1 (bearing plus U 410), not the 45.6 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The sphered housing washer of 53410 MUST run against the U 410 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53410 as the single sphered pressed steel execution; other order numbers of the 53410 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 410 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53410?",
        "a": "53410 measures 50 mm bore × 110 mm OD × 45.6 mm bearing height (1.969 × 4.331 × 1.795 in), or 50 mm mounted H1 including the U 410 seat washer, mass about 2300 g. SKF 17000 ratings: C 159 kN, C0 340 kN, Pu 12.5 kN, reference speed 1,900 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53410 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 10 encode the bore as 50 mm (code 10 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Why does 53410 need a U 410 seat washer?",
        "a": "The housing washer of 53410 has a sphered back face. The U 410 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      },
      {
        "q": "Is the U 410 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53410 and U 410 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53410",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53410",
      "53410 + U 410"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53211",
    "brand": "SKF",
    "manufacturer_designation": "53211",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 90,
    "B_mm": 27.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 58.5,
    "static_load_kN": 134,
    "fatigue_load_limit_kN": 4.9,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53211 is SKF's 55 mm-bore single-direction thrust ball bearing in the 53200 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 55×90×27.3 mm U 211 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 11 encode the bore as 55 mm (code 11 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 55×90×27.3 mm (2.165×3.543×1.075 in), 17.5 mm radial section, C 58.5 kN, C0 134 kN, Pu 4.9 kN. Mounted height H1 30 mm includes the U 211 seat washer; the bearing alone is 27.3 mm high. reference speed 2,800 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 750 g. Speed band width for this size is 1,000 r/min between reference and limiting (1.36× ratio); lubrication, preload and heat removal decide where inside that band 53211 can actually run. Static-first selection data: 134 kN C0 spread across the 27.3 mm stack gives 4.9 kN of static rating per height millimetre, and the 750 g mass/C0 ratio is about 6 g per static kN — crane-hook and screw positions are normally sized on these two figures. Rating split for documentation: dynamic 58.5 kN (L10 life), static 134 kN (safety factor s0), fatigue limit 4.9 kN (adjusted life) — three different uses of three different numbers for 53211, none interchangeable with another. Minimum-load arithmetic: with dm ≈ 72.5 mm and factor A 0.11, Fam ≈ A·(n·dm/1000)² at the 2,800 r/min reference speed is about 4.5 kN for 53211; below that preload the balls skid and smear the tracks. Envelope economics: the 27.3 mm axial height over a 17.5 mm radial section yields 2.1 kN of dynamic capacity per height millimetre, and the bearing weighs 750 g for 58.5 kN C — about 13 g per rated kN. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 90 mm washer can tilt inside the U 211 seat; check the actual tilt allowance in the mounting drawing, since the 2.7 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "machine-tool supports on less rigid fabricated housings",
      "vertical pumps with shaft-to-housing misalignment",
      "screw-jack spindles that bend under load"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Dimension the housing to the 30 mm mounted height H1 (bearing plus U 211), not the 27.3 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The sphered housing washer of 53211 MUST run against the U 211 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "The shaft washer remains the tight, ground-bore component on the 55 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 211 into the register.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Ordering discipline for 53211: the catalogue page quotes 53211 plus U 211 and its 58.5/134 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53211?",
        "a": "53211 measures 55 mm bore × 90 mm OD × 27.3 mm bearing height (2.165 × 3.543 × 1.075 in), or 30 mm mounted H1 including the U 211 seat washer, mass about 750 g. SKF 17000 ratings: C 58.5 kN, C0 134 kN, Pu 4.9 kN, reference speed 2,800 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53211 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 11 encode the bore as 55 mm (code 11 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53211 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53211",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53211",
      "53211 + U 211"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53311",
    "brand": "SKF",
    "manufacturer_designation": "53311",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 105,
    "B_mm": 39.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 101,
    "static_load_kN": 224,
    "fatigue_load_limit_kN": 8.3,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 1700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 53300 series order number 53311 is a SKF single-direction thrust ball bearing for a 55 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 55×105×39.3 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 11 decodes to 55 mm (code 11 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 55×105×39.3 mm (2.165×4.134×1.547 in), 25.0 mm radial section, C 101 kN, C0 224 kN, Pu 8.3 kN. Mounted height H1 42 mm includes the U 311 seat washer; the bearing alone is 39.3 mm high. reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 1700 g. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 3,000 r/min while thermal balance under catalogue load sets the 2,200 r/min reference; at dm ≈ 80.0 mm the corresponding dn is approximately 240k mm·r/min. Load balance: C0 224 kN against C 101 kN gives a 2.22 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 8.3 kN enters the adjusted-life check. Sizing arithmetic on the 55 mm bore: 101 kN C over the 25.0 mm radial section gives 4.0 kN per section millimetre, and the 39.3 mm stack height is 1.57× that section — proportions typical of a 53300 thrust section. Light-load floor: Pu = 8.3 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 53311; the number is 8 % of the 101 kN dynamic rating. Mass and section check: 1700 g inside the 55×105×39.3 mm outline leaves a 25.0 mm radial section, and the 224 kN static rating is 2.22× the dynamic rating — plan static safety and minimum preload against those figures. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 105 mm washer can tilt inside the U 311 seat; check the actual tilt allowance in the mounting drawing, since the 2.7 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "vertical pumps with shaft-to-housing misalignment",
      "screw-jack spindles that bend under load",
      "crane hooks whose block deflects under offset lifts"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "edge loading on the ball set when the U seat washer is fitted with its concave face reversed",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Minimum axial load still applies with factor A 0.26: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 311 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The 101/224 kN figures belong to 53311 specifically (the single sphered pressed steel execution of 53311); suffixed, sphered and counterpart-series order numbers are separate articles, and U 311 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53311?",
        "a": "Boundary dimensions to ISO 104: bore 55 mm, OD 105 mm, height 39.3 mm (H1 42 mm installed with the U 311 seat washer); weight 1700 g. Load figures from SKF 17000: dynamic 101 kN, static 224 kN, fatigue limit 8.3 kN; reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53311 mean?",
        "a": "the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 11 decodes to 55 mm (code 11 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is 53311 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53311",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53311",
      "53311 + U 311"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53411",
    "brand": "SKF",
    "manufacturer_designation": "53411",
    "series": "53400-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 50.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 195,
    "static_load_kN": 400,
    "fatigue_load_limit_kN": 14.6,
    "reference_speed_rpm": 1700,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 3100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53411 is SKF's 55 mm-bore single-direction thrust ball bearing in the 53400 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 55×120×50.5 mm U 411 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 11 encode the bore as 55 mm (code 11 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 55×120×50.5 mm (2.165×4.724×1.988 in), 32.5 mm radial section, C 195 kN, C0 400 kN, Pu 14.6 kN. Mounted height H1 55 mm includes the U 411 seat washer; the bearing alone is 50.5 mm high. reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 3100 g. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 2,400 r/min while thermal balance under catalogue load sets the 1,700 r/min reference; at dm ≈ 87.5 mm the corresponding dn is approximately 210k mm·r/min. Bore-to-OD planning: OD 120 over bore 55 is a 2.18× step for this size, and the 50.5 mm height gives a bore/height ratio of 1.09; use these ratios when the housing recess around the 55 mm shaft is the first constraint. Track-circle loading: per millimetre of mean track circumference the 195 kN dynamic rating corresponds to roughly 0.71 kN/mm of π·dm track, a useful comparison against the other dimension series of the 55 mm bore. Pitch-diameter arithmetic: dm = (55+120)/2 = 87.5 mm; at the 2,400 r/min limiting speed that corresponds to roughly 210k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Washer-annulus check: the π/4·(D²−d²) contact annulus of 53411 covers about 8,934 mm², distributing C0 400 kN over a mean track circle of π·dm ≈ 275 mm. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53411 and U 411 are two order numbers shipping as two articles; the installed 55 mm H1 rather than 50.5 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "screw-jack spindles that bend under load",
      "machine-tool supports on less rigid fabricated housings",
      "crane hooks whose block deflects under offset lifts"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "fretting corrosion in the spherical interface under oscillation with no grease between washer and seat",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Minimum axial load still applies with factor A 0.79: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 411 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The 195/400 kN figures belong to 53411 specifically (the single sphered pressed steel execution of 53411); suffixed, sphered and counterpart-series order numbers are separate articles, and U 411 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53411?",
        "a": "53411 measures 55 mm bore × 120 mm OD × 50.5 mm bearing height (2.165 × 4.724 × 1.988 in), or 55 mm mounted H1 including the U 411 seat washer, mass about 3100 g. SKF 17000 ratings: C 195 kN, C0 400 kN, Pu 14.6 kN, reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53411 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 11 encode the bore as 55 mm (code 11 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53411 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53411",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53411",
      "53411 + U 411"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53212",
    "brand": "SKF",
    "manufacturer_designation": "53212",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 95,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 59.2,
    "static_load_kN": 140,
    "fatigue_load_limit_kN": 5.1,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 820,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53212 is SKF's 60 mm-bore single-direction thrust ball bearing in the 53200 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 60×95×28 mm U 212 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 12 encode the bore as 60 mm (code 12 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 60×95×28 mm (2.362×3.74×1.102 in), 17.5 mm radial section, C 59.2 kN, C0 140 kN, Pu 5.1 kN. Mounted height H1 31 mm includes the U 212 seat washer; the bearing alone is 28 mm high. reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 820 g. Sizing arithmetic on the 60 mm bore: 59.2 kN C over the 17.5 mm radial section gives 3.4 kN per section millimetre, and the 28 mm stack height is 1.60× that section — proportions typical of a 53200 thrust section. Imperial cross-check for procurement drawings: 2.362 in bore, 3.74 in OD, 1.102 in height, and the 820 g catalogue mass converts to 0.820 kg (28.9 oz). Mass and section check: 820 g inside the 60×95×28 mm outline leaves a 17.5 mm radial section, and the 140 kN static rating is 2.36× the dynamic rating — plan static safety and minimum preload against those figures. Rating split for documentation: dynamic 59.2 kN (L10 life), static 140 kN (safety factor s0), fatigue limit 5.1 kN (adjusted life) — three different uses of three different numbers for 53212, none interchangeable with another. Selection figures for 53212: the C0/C ratio is 2.36, Pu 5.1 kN is about 9 % of C, and the catalogue mass works out to roughly 14 g per millimetre of bore; the printed minimum-load factor is A 0.12. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53212 and U 212 are two order numbers shipping as two articles; the installed 31 mm H1 rather than 28 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "large screw jacks on elastic frames",
      "heavy hook blocks and lifting equipment",
      "winch drums on fabricated structures"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 212 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "Minimum axial load still applies with factor A 0.12: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "Dimension the housing to the 31 mm mounted height H1 (bearing plus U 212), not the 28 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "Ordering discipline for 53212: the catalogue page quotes 53212 plus U 212 and its 59.2/140 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53212?",
        "a": "53212 measures 60 mm bore × 95 mm OD × 28 mm bearing height (2.362 × 3.74 × 1.102 in), or 31 mm mounted H1 including the U 212 seat washer, mass about 820 g. SKF 17000 ratings: C 59.2 kN, C0 140 kN, Pu 5.1 kN, reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53212 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 12 encode the bore as 60 mm (code 12 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Why does 53212 need a U 212 seat washer?",
        "a": "The housing washer of 53212 has a sphered back face. The U 212 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      },
      {
        "q": "Is the U 212 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53212 and U 212 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53212",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53212",
      "53212 + U 212"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53312",
    "brand": "SKF",
    "manufacturer_designation": "53312",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 38.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 101,
    "static_load_kN": 224,
    "fatigue_load_limit_kN": 8.3,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 1700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53312 is SKF's 60 mm-bore single-direction thrust ball bearing in the 53300 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 60×110×38.3 mm U 312 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 12 encode the bore as 60 mm (code 12 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 60×110×38.3 mm (2.362×4.331×1.508 in), 25.0 mm radial section, C 101 kN, C0 224 kN, Pu 8.3 kN. Mounted height H1 42 mm includes the U 312 seat washer; the bearing alone is 38.3 mm high. reference speed 2,000 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 1700 g. Track-circle loading: per millimetre of mean track circumference the 101 kN dynamic rating corresponds to roughly 0.38 kN/mm of π·dm track, a useful comparison against the other dimension series of the 60 mm bore. Selection figures for 53312: the C0/C ratio is 2.22, Pu 8.3 kN is about 8 % of C, and the catalogue mass works out to roughly 28 g per millimetre of bore; the printed minimum-load factor is A 0.26. Imperial cross-check for procurement drawings: 2.362 in bore, 4.331 in OD, 1.508 in height, and the 1700 g catalogue mass converts to 1.700 kg (60.0 oz). Capacity density: 101 kN C from 1.700 kg of bearing steel gives about 59.4 kN per kilogram; static density is correspondingly 131.8 kN/kg at C0 224 kN. Rating split for documentation: dynamic 101 kN (L10 life), static 224 kN (safety factor s0), fatigue limit 8.3 kN (adjusted life) — three different uses of three different numbers for 53312, none interchangeable with another. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53312 and U 312 are two order numbers shipping as two articles; the installed 42 mm H1 rather than 38.3 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "vertical process pumps on welded housings",
      "marine deck-machinery pivots",
      "winch drums on fabricated structures"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "edge loading on the ball set when the U seat washer is fitted with its concave face reversed",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "false brinelling of the stationary tracks while the machine stands under vibration"
    ],
    "pitfalls": [
      "Replacement orders must list both 53312 and U 312: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 224 kN static-rated set.",
      "Dimension the housing to the 42 mm mounted height H1 (bearing plus U 312), not the 38.3 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 312 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The shaft washer remains the tight, ground-bore component on the 60 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 312 into the register.",
      "The 101/224 kN figures belong to 53312 specifically (the single sphered pressed steel execution of 53312); suffixed, sphered and counterpart-series order numbers are separate articles, and U 312 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53312?",
        "a": "53312 measures 60 mm bore × 110 mm OD × 38.3 mm bearing height (2.362 × 4.331 × 1.508 in), or 42 mm mounted H1 including the U 312 seat washer, mass about 1700 g. SKF 17000 ratings: C 101 kN, C0 224 kN, Pu 8.3 kN, reference speed 2,000 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53312 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 12 encode the bore as 60 mm (code 12 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53312 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53312",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53312",
      "53312 + U 312"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53412-M",
    "brand": "SKF",
    "manufacturer_designation": "53412 M",
    "series": "53400-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 54,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 199,
    "static_load_kN": 430,
    "fatigue_load_limit_kN": 16,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 3800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53412 M is SKF's 60 mm-bore single-direction thrust ball bearing in the 53400 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 60×130×54 mm U 412 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 12 encode the bore as 60 mm (code 12 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 60×130×54 mm (2.362×5.118×2.126 in), 35.0 mm radial section, C 199 kN, C0 430 kN, Pu 16 kN. Mounted height H1 58 mm includes the U 412 seat washer; the bearing alone is 54 mm high. reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 3800 g. Speed planning separates the two ceilings mechanically: the pressed brass cage and balls tolerate 2,200 r/min while thermal balance under catalogue load sets the 1,600 r/min reference; at dm ≈ 95.0 mm the corresponding dn is approximately 209k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 1,600 r/min against a 2,200 r/min limiting speed, a reference-to-limit ratio of 0.73. Track-circle loading: per millimetre of mean track circumference the 199 kN dynamic rating corresponds to roughly 0.67 kN/mm of π·dm track, a useful comparison against the other dimension series of the 60 mm bore. Minimum-load arithmetic: with dm ≈ 95.0 mm and factor A 0.96, Fam ≈ A·(n·dm/1000)² at the 1,600 r/min reference speed is about 22.2 kN for 53412 M; below that preload the balls skid and smear the tracks. Washer-stack proportions: the U 412 seat washer adds 4.0 mm to the 54 mm bearing height for a mounted H1 of 58 mm, while the 35.0 mm radial section against 60 mm bore (section/bore ≈ 0.58) identifies the envelope. Heavy sphered-execution note: this M order number combines the machined brass ball-centred cage with the sphered housing washer and its U seat washer; it is the large-bore answer for hook blocks and pivots whose fabricated structure deflects — verify the spherical pair swivels freely under a light preload before the working load goes on. The M brass-cage option at 60 mm bore pairs the heavy-section cage with the U 412 seat requirement — order all three articles (bearing + U washer + appropriate lubricant) together, and log the H1 58 mm installed dimension on the maintenance card.",
    "applications": [
      "heavy hook blocks and lifting equipment",
      "marine deck-machinery pivots",
      "vertical process pumps on welded housings"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "corrosion lock of the spherical pair during long outdoor idleness with no preservative grease",
      "fretting between the sphered washer and U seat washer when the spherical interface runs dry under oscillation",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "The shaft washer remains the tight, ground-bore component on the 60 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 412 into the register.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Replacement orders must list both 53412 M and U 412: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 430 kN static-rated set.",
      "Ordering discipline for 53412: the catalogue page quotes 53412 M plus U 412 and its 199/430 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53412-M?",
        "a": "53412 M measures 60 mm bore × 130 mm OD × 54 mm bearing height (2.362 × 5.118 × 2.126 in), or 58 mm mounted H1 including the U 412 seat washer, mass about 3800 g. SKF 17000 ratings: C 199 kN, C0 430 kN, Pu 16 kN, reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53412 M mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 12 encode the bore as 60 mm (code 12 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53412-M accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53412",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53412-M",
      "53412 M",
      "53412 M + U 412"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53213",
    "brand": "SKF",
    "manufacturer_designation": "53213",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 100,
    "B_mm": 28.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 60.5,
    "static_load_kN": 150,
    "fatigue_load_limit_kN": 5.5,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 910,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53213 is an ISO 104 single-direction thrust ball bearing, 65 mm bore and 100 mm OD, with a sphered housing washer and U seat washer, standing 28.7 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 13: bore 65 mm (code 13 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 65×100×28.7 mm (2.559×3.937×1.13 in), 17.5 mm radial section, C 60.5 kN, C0 150 kN, Pu 5.5 kN. Mounted height H1 32 mm includes the U 213 seat washer; the bearing alone is 28.7 mm high. reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 910 g. Minimum-load arithmetic: with dm ≈ 82.5 mm and factor A 0.14, Fam ≈ A·(n·dm/1000)² at the 2,600 r/min reference speed is about 6.4 kN for 53213; below that preload the balls skid and smear the tracks. Bore-to-OD planning: OD 100 over bore 65 is a 1.54× step for this size, and the 28.7 mm height gives a bore/height ratio of 2.26; use these ratios when the housing recess around the 65 mm shaft is the first constraint. Capacity density: 60.5 kN C from 0.910 kg of bearing steel gives about 66.5 kN per kilogram; static density is correspondingly 164.8 kN/kg at C0 150 kN. Load balance: C0 150 kN against C 60.5 kN gives a 2.48 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 5.5 kN enters the adjusted-life check. Stack/annulus proportions: the 28.7 mm axial stack over the 4,536 mm² washer annulus gives 6.33 mm of height per annular square millimetre ×10⁻³, and at 910 g the bearing holds about 164.8 kN of C0 per kilogram. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 100 mm washer can tilt inside the U 213 seat; check the actual tilt allowance in the mounting drawing, since the 3.3 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "heavy hook blocks and lifting equipment",
      "winch drums on fabricated structures",
      "marine deck-machinery pivots"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The shaft washer remains the tight, ground-bore component on the 65 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 213 into the register.",
      "Minimum axial load still applies with factor A 0.14: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "The sphered housing washer of 53213 MUST run against the U 213 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53213 as the single sphered pressed steel execution; other order numbers of the 53213 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 213 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53213?",
        "a": "The catalogue envelope is 65×100×28.7 mm plus the 3.3 mm the U 213 seat washer adds to reach H1 32 mm, mass 910 g; ratings C 60.5 kN / C0 150 kN / Pu 5.5 kN, reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53213 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 13: bore 65 mm (code 13 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is the U 213 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53213 and U 213 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      },
      {
        "q": "Is 53213 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53213",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53213",
      "53213 + U 213"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53313",
    "brand": "SKF",
    "manufacturer_designation": "53313",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 115,
    "B_mm": 39.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 106,
    "static_load_kN": 240,
    "fatigue_load_limit_kN": 8.8,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 1900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 53300 series order number 53313 is a SKF single-direction thrust ball bearing for a 65 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 65×115×39.4 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 13 decodes to 65 mm (code 13 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 65×115×39.4 mm (2.559×4.528×1.551 in), 25.0 mm radial section, C 106 kN, C0 240 kN, Pu 8.8 kN. Mounted height H1 43 mm includes the U 313 seat washer; the bearing alone is 39.4 mm high. reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical), catalogue mass 1900 g. Sizing arithmetic on the 65 mm bore: 106 kN C over the 25.0 mm radial section gives 4.2 kN per section millimetre, and the 39.4 mm stack height is 1.58× that section — proportions typical of a 53300 thrust section. Stack/annulus proportions: the 39.4 mm axial stack over the 7,069 mm² washer annulus gives 5.57 mm of height per annular square millimetre ×10⁻³, and at 1900 g the bearing holds about 126.3 kN of C0 per kilogram. Imperial cross-check for procurement drawings: 2.559 in bore, 4.528 in OD, 1.551 in height, and the 1900 g catalogue mass converts to 1.900 kg (67.0 oz). Minimum-load arithmetic: with dm ≈ 90.0 mm and factor A 0.3, Fam ≈ A·(n·dm/1000)² at the 2,000 r/min reference speed is about 9.7 kN for 53313; below that preload the balls skid and smear the tracks. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 2,800 r/min while thermal balance under catalogue load sets the 2,000 r/min reference; at dm ≈ 90.0 mm the corresponding dn is approximately 252k mm·r/min. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53313 and U 313 are two order numbers shipping as two articles; the installed 43 mm H1 rather than 39.4 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "large screw jacks on elastic frames",
      "marine deck-machinery pivots",
      "vertical process pumps on welded housings"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "tilted running after a mismatched U washer leaves only a narrow band of spherical contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The shaft washer remains the tight, ground-bore component on the 65 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 313 into the register.",
      "Minimum axial load still applies with factor A 0.3: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "Replacement orders must list both 53313 and U 313: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 240 kN static-rated set.",
      "The sphered housing washer of 53313 MUST run against the U 313 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53313 as the single sphered pressed steel execution; other order numbers of the 53313 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 313 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53313?",
        "a": "Boundary dimensions to ISO 104: bore 65 mm, OD 115 mm, height 39.4 mm (H1 43 mm installed with the U 313 seat washer); weight 1900 g. Load figures from SKF 17000: dynamic 106 kN, static 240 kN, fatigue limit 8.8 kN; reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53313 mean?",
        "a": "the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 13 decodes to 65 mm (code 13 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is 53313 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53313",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53313",
      "53313 + U 313"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53214",
    "brand": "SKF",
    "manufacturer_designation": "53214",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 105,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 62.4,
    "static_load_kN": 160,
    "fatigue_load_limit_kN": 5.85,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 970,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53214 is SKF's 70 mm-bore single-direction thrust ball bearing in the 53200 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 70×105×27 mm U 214 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 14 encode the bore as 70 mm (code 14 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 70×105×27 mm (2.756×4.134×1.063 in), 17.5 mm radial section, C 62.4 kN, C0 160 kN, Pu 5.85 kN. Mounted height H1 32 mm includes the U 214 seat washer; the bearing alone is 27 mm high. reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 970 g. Pitch-diameter arithmetic: dm = (70+105)/2 = 87.5 mm; at the 3,600 r/min limiting speed that corresponds to roughly 315k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Selection figures for 53214: the C0/C ratio is 2.56, Pu 5.85 kN is about 9 % of C, and the catalogue mass works out to roughly 14 g per millimetre of bore; the printed minimum-load factor is A 0.16. Capacity density: 62.4 kN C from 0.970 kg of bearing steel gives about 64.3 kN per kilogram; static density is correspondingly 164.9 kN/kg at C0 160 kN. Speed band width for this size is 1,000 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 53214 can actually run. Envelope economics: the 27 mm axial height over a 17.5 mm radial section yields 2.3 kN of dynamic capacity per height millimetre, and the bearing weighs 970 g for 62.4 kN C — about 16 g per rated kN. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53214 and U 214 are two order numbers shipping as two articles; the installed 32 mm H1 rather than 27 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "vertical process pumps on welded housings",
      "marine deck-machinery pivots",
      "heavy hook blocks and lifting equipment"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "tilted running after a mismatched U washer leaves only a narrow band of spherical contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Replacement orders must list both 53214 and U 214: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 160 kN static-rated set.",
      "Minimum axial load still applies with factor A 0.16: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The shaft washer remains the tight, ground-bore component on the 70 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 214 into the register.",
      "Ordering discipline for 53214: the catalogue page quotes 53214 plus U 214 and its 62.4/160 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53214?",
        "a": "53214 measures 70 mm bore × 105 mm OD × 27 mm bearing height (2.756 × 4.134 × 1.063 in), or 32 mm mounted H1 including the U 214 seat washer, mass about 970 g. SKF 17000 ratings: C 62.4 kN, C0 160 kN, Pu 5.85 kN, reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53214 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 14 encode the bore as 70 mm (code 14 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Why does 53214 need a U 214 seat washer?",
        "a": "The housing washer of 53214 has a sphered back face. The U 214 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      },
      {
        "q": "Is the U 214 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53214 and U 214 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "51214-SKF",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×105×27 mm ISO 104 thrust-ball envelope with catalogue ratings within 10 %; 51214 is the single-direction flat-seat, stamped sheet-steel cage execution of this size — boundary dimensions interchangeable, execution differs. Bearing heights match, but this sphered SKF execution additionally needs its U 214 seat washer and stands 32 mm (H1) when mounted."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53214",
      "53214 + U 214"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53314",
    "brand": "SKF",
    "manufacturer_designation": "53314",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 44.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 135,
    "static_load_kN": 320,
    "fatigue_load_limit_kN": 11.8,
    "reference_speed_rpm": 1800,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 2500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53314 is an ISO 104 single-direction thrust ball bearing, 70 mm bore and 125 mm OD, with a sphered housing washer and U seat washer, standing 44.2 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 14: bore 70 mm (code 14 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 70×125×44.2 mm (2.756×4.921×1.74 in), 27.5 mm radial section, C 135 kN, C0 320 kN, Pu 11.8 kN. Mounted height H1 48 mm includes the U 314 seat washer; the bearing alone is 44.2 mm high. reference speed 1,800 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 2500 g. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 2,600 r/min while thermal balance under catalogue load sets the 1,800 r/min reference; at dm ≈ 97.5 mm the corresponding dn is approximately 254k mm·r/min. Imperial cross-check for procurement drawings: 2.756 in bore, 4.921 in OD, 1.74 in height, and the 2500 g catalogue mass converts to 2.500 kg (88.2 oz). Sizing arithmetic on the 70 mm bore: 135 kN C over the 27.5 mm radial section gives 4.9 kN per section millimetre, and the 44.2 mm stack height is 1.61× that section — proportions typical of a 53300 thrust section. Rating split for documentation: dynamic 135 kN (L10 life), static 320 kN (safety factor s0), fatigue limit 11.8 kN (adjusted life) — three different uses of three different numbers for 53314, none interchangeable with another. Selection figures for 53314: the C0/C ratio is 2.37, Pu 11.8 kN is about 9 % of C, and the catalogue mass works out to roughly 36 g per millimetre of bore; the printed minimum-load factor is A 0.53. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53314 and U 314 are two order numbers shipping as two articles; the installed 48 mm H1 rather than 44.2 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "vertical process pumps on welded housings",
      "winch drums on fabricated structures",
      "marine deck-machinery pivots"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "cage damage from mounting force applied through the balls instead of the washer face",
      "edge loading on the ball set when the U seat washer is fitted with its concave face reversed",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Replacement orders must list both 53314 and U 314: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 320 kN static-rated set.",
      "Dimension the housing to the 48 mm mounted height H1 (bearing plus U 314), not the 44.2 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The shaft washer remains the tight, ground-bore component on the 70 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 314 into the register.",
      "Minimum axial load still applies with factor A 0.53: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "Ordering discipline for 53314: the catalogue page quotes 53314 plus U 314 and its 135/320 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53314?",
        "a": "The catalogue envelope is 70×125×44.2 mm plus the 3.8 mm the U 314 seat washer adds to reach H1 48 mm, mass 2500 g; ratings C 135 kN / C0 320 kN / Pu 11.8 kN, reference speed 1,800 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53314 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 14: bore 70 mm (code 14 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is the U 314 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53314 and U 314 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      },
      {
        "q": "Is 53314 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53314",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53314",
      "53314 + U 314"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53414-M",
    "brand": "SKF",
    "manufacturer_designation": "53414 M",
    "series": "53400-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 63.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 234,
    "static_load_kN": 550,
    "fatigue_load_limit_kN": 19.3,
    "reference_speed_rpm": 1400,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "weight_g": 6500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53414 M is SKF's 70 mm-bore single-direction thrust ball bearing in the 53400 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 70×150×63.6 mm U 414 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 14 encode the bore as 70 mm (code 14 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 70×150×63.6 mm (2.756×5.906×2.504 in), 40.0 mm radial section, C 234 kN, C0 550 kN, Pu 19.3 kN. Mounted height H1 69 mm includes the U 414 seat washer; the bearing alone is 63.6 mm high. reference speed 1,400 r/min (thermal) and limiting speed 2,000 r/min (mechanical), catalogue mass 6500 g. Light-load floor: Pu = 19.3 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 53414 M; the number is 8 % of the 234 kN dynamic rating. Speed-ratio note for this exact unit: the reference speed is 1,400 r/min against a 2,000 r/min limiting speed, a reference-to-limit ratio of 0.70. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 1.6 at the 2,000 r/min limiting speed raises the required axial preload to about 77.4 kN; the reference-speed value 37.9 kN is the thermal design point. Envelope economics: the 63.6 mm axial height over a 40.0 mm radial section yields 3.7 kN of dynamic capacity per height millimetre, and the bearing weighs 6500 g for 234 kN C — about 28 g per rated kN. Static-first selection data: 550 kN C0 spread across the 63.6 mm stack gives 8.6 kN of static rating per height millimetre, and the 6500 g mass/C0 ratio is about 12 g per static kN — crane-hook and screw positions are normally sized on these two figures. Heavy sphered-execution note: this M order number combines the machined brass ball-centred cage with the sphered housing washer and its U seat washer; it is the large-bore answer for hook blocks and pivots whose fabricated structure deflects — verify the spherical pair swivels freely under a light preload before the working load goes on. Under 550 kN static load the spherical interface of 53414 M must stay lubricated with a grease that does not separate at rest; a dry sphered contact under hook-block shock frets even though the ball tracks remain unworn.",
    "applications": [
      "large screw jacks on elastic frames",
      "winch drums on fabricated structures",
      "heavy hook blocks and lifting equipment"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "fretting between the sphered washer and U seat washer when the spherical interface runs dry under oscillation",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The shaft washer remains the tight, ground-bore component on the 70 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 414 into the register.",
      "Minimum axial load still applies with factor A 1.6: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The sphered housing washer of 53414 M MUST run against the U 414 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 414 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53414 M as the single sphered brass execution; other order numbers of the 53414 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 414 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53414-M?",
        "a": "53414 M measures 70 mm bore × 150 mm OD × 63.6 mm bearing height (2.756 × 5.906 × 2.504 in), or 69 mm mounted H1 including the U 414 seat washer, mass about 6500 g. SKF 17000 ratings: C 234 kN, C0 550 kN, Pu 19.3 kN, reference speed 1,400 r/min (thermal) and limiting speed 2,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53414 M mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 14 encode the bore as 70 mm (code 14 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53414-M accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53414",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53414-M",
      "53414 M",
      "53414 M + U 414"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53215",
    "brand": "SKF",
    "manufacturer_designation": "53215",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 75,
    "D_mm": 110,
    "B_mm": 28.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 63.7,
    "static_load_kN": 170,
    "fatigue_load_limit_kN": 6.2,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 1000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53215 is SKF's 75 mm-bore single-direction thrust ball bearing in the 53200 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 75×110×28.3 mm U 215 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 15 encode the bore as 75 mm (code 15 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 75×110×28.3 mm (2.953×4.331×1.114 in), 17.5 mm radial section, C 63.7 kN, C0 170 kN, Pu 6.2 kN. Mounted height H1 32 mm includes the U 215 seat washer; the bearing alone is 28.3 mm high. reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 1000 g. Rating split for documentation: dynamic 63.7 kN (L10 life), static 170 kN (safety factor s0), fatigue limit 6.2 kN (adjusted life) — three different uses of three different numbers for 53215, none interchangeable with another. Speed-ratio note for this exact unit: the reference speed is 2,400 r/min against a 3,400 r/min limiting speed, a reference-to-limit ratio of 0.71. Stack/annulus proportions: the 28.3 mm axial stack over the 5,085 mm² washer annulus gives 5.57 mm of height per annular square millimetre ×10⁻³, and at 1000 g the bearing holds about 170.0 kN of C0 per kilogram. Bore-to-OD planning: OD 110 over bore 75 is a 1.47× step for this size, and the 28.3 mm height gives a bore/height ratio of 2.65; use these ratios when the housing recess around the 75 mm shaft is the first constraint. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 3,400 r/min while thermal balance under catalogue load sets the 2,400 r/min reference; at dm ≈ 92.5 mm the corresponding dn is approximately 315k mm·r/min. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 110 mm washer can tilt inside the U 215 seat; check the actual tilt allowance in the mounting drawing, since the 3.7 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "heavy hook blocks and lifting equipment",
      "winch drums on fabricated structures",
      "large screw jacks on elastic frames"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Replacement orders must list both 53215 and U 215: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 170 kN static-rated set.",
      "Dimension the housing to the 32 mm mounted height H1 (bearing plus U 215), not the 28.3 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "Minimum axial load still applies with factor A 0.17: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53215 as the single sphered pressed steel execution; other order numbers of the 53215 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 215 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53215?",
        "a": "53215 measures 75 mm bore × 110 mm OD × 28.3 mm bearing height (2.953 × 4.331 × 1.114 in), or 32 mm mounted H1 including the U 215 seat washer, mass about 1000 g. SKF 17000 ratings: C 63.7 kN, C0 170 kN, Pu 6.2 kN, reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53215 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 15 encode the bore as 75 mm (code 15 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53215 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53215",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53215",
      "53215 + U 215"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53315",
    "brand": "SKF",
    "manufacturer_designation": "53315",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 75,
    "D_mm": 135,
    "B_mm": 48.1,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 163,
    "static_load_kN": 390,
    "fatigue_load_limit_kN": 14,
    "reference_speed_rpm": 1700,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 3200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53315 is an ISO 104 single-direction thrust ball bearing, 75 mm bore and 135 mm OD, with a sphered housing washer and U seat washer, standing 48.1 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 15: bore 75 mm (code 15 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 75×135×48.1 mm (2.953×5.315×1.894 in), 30.0 mm radial section, C 163 kN, C0 390 kN, Pu 14 kN. Mounted height H1 52 mm includes the U 315 seat washer; the bearing alone is 48.1 mm high. reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 3200 g. Track-circle loading: per millimetre of mean track circumference the 163 kN dynamic rating corresponds to roughly 0.49 kN/mm of π·dm track, a useful comparison against the other dimension series of the 75 mm bore. Capacity density: 163 kN C from 3.200 kg of bearing steel gives about 50.9 kN per kilogram; static density is correspondingly 121.9 kN/kg at C0 390 kN. Stack/annulus proportions: the 48.1 mm axial stack over the 9,896 mm² washer annulus gives 4.86 mm of height per annular square millimetre ×10⁻³, and at 3200 g the bearing holds about 121.9 kN of C0 per kilogram. Pitch-diameter arithmetic: dm = (75+135)/2 = 105.0 mm; at the 2,400 r/min limiting speed that corresponds to roughly 252k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Rating split for documentation: dynamic 163 kN (L10 life), static 390 kN (safety factor s0), fatigue limit 14 kN (adjusted life) — three different uses of three different numbers for 53315, none interchangeable with another. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 135 mm washer can tilt inside the U 315 seat; check the actual tilt allowance in the mounting drawing, since the 3.9 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "marine deck-machinery pivots",
      "heavy hook blocks and lifting equipment",
      "winch drums on fabricated structures"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "edge loading on the ball set when the U seat washer is fitted with its concave face reversed",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "The shaft washer remains the tight, ground-bore component on the 75 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 315 into the register.",
      "The sphered housing washer of 53315 MUST run against the U 315 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Replacement orders must list both 53315 and U 315: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 390 kN static-rated set.",
      "The 163/390 kN figures belong to 53315 specifically (the single sphered pressed steel execution of 53315); suffixed, sphered and counterpart-series order numbers are separate articles, and U 315 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53315?",
        "a": "The catalogue envelope is 75×135×48.1 mm plus the 3.9 mm the U 315 seat washer adds to reach H1 52 mm, mass 3200 g; ratings C 163 kN / C0 390 kN / Pu 14 kN, reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53315 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 15: bore 75 mm (code 15 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "How much misalignment can 53315 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      },
      {
        "q": "What is the difference between H and H1?",
        "a": "H 48.1 mm is the height of the bearing itself; H1 52 mm is the installed height including the U 315 seat washer. Housing recesses and cover stacks must be drawn to H1, not H."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53315",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53315",
      "53315 + U 315"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53415-M",
    "brand": "SKF",
    "manufacturer_designation": "53415 M",
    "series": "53400-series",
    "type": "thrust_ball",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 69,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 251,
    "static_load_kN": 610,
    "fatigue_load_limit_kN": 20.8,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "weight_g": 8100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 53400 series order number 53415 M is a SKF single-direction thrust ball bearing for a 75 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 75×160×69 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 15 decodes to 75 mm (code 15 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 75×160×69 mm (2.953×6.299×2.717 in), 42.5 mm radial section, C 251 kN, C0 610 kN, Pu 20.8 kN. Mounted height H1 75 mm includes the U 415 seat washer; the bearing alone is 69 mm high. reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical), catalogue mass 8100 g. Mass and section check: 8100 g inside the 75×160×69 mm outline leaves a 42.5 mm radial section, and the 610 kN static rating is 2.43× the dynamic rating — plan static safety and minimum preload against those figures. Speed planning separates the two ceilings mechanically: the pressed brass cage and balls tolerate 1,800 r/min while thermal balance under catalogue load sets the 1,300 r/min reference; at dm ≈ 117.5 mm the corresponding dn is approximately 212k mm·r/min. Minimum-load arithmetic: with dm ≈ 117.5 mm and factor A 1.9, Fam ≈ A·(n·dm/1000)² at the 1,300 r/min reference speed is about 44.3 kN for 53415 M; below that preload the balls skid and smear the tracks. Speed band width for this size is 500 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 53415 M can actually run. Envelope economics: the 69 mm axial height over a 42.5 mm radial section yields 3.6 kN of dynamic capacity per height millimetre, and the bearing weighs 8100 g for 251 kN C — about 32 g per rated kN. Heavy sphered-execution note: this M order number combines the machined brass ball-centred cage with the sphered housing washer and its U seat washer; it is the large-bore answer for hook blocks and pivots whose fabricated structure deflects — verify the spherical pair swivels freely under a light preload before the working load goes on. The M brass-cage option at 75 mm bore pairs the heavy-section cage with the U 415 seat requirement — order all three articles (bearing + U washer + appropriate lubricant) together, and log the H1 75 mm installed dimension on the maintenance card.",
    "applications": [
      "heavy hook blocks and lifting equipment",
      "large screw jacks on elastic frames",
      "winch drums on fabricated structures"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "fretting between the sphered washer and U seat washer when the spherical interface runs dry under oscillation",
      "track rust staining from condensate during long idle periods in humid plant air",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Dimension the housing to the 75 mm mounted height H1 (bearing plus U 415), not the 69 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The sphered housing washer of 53415 M MUST run against the U 415 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Minimum axial load still applies with factor A 1.9: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "The 251/610 kN figures belong to 53415 M specifically (the single sphered brass execution of 53415); suffixed, sphered and counterpart-series order numbers are separate articles, and U 415 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53415-M?",
        "a": "Boundary dimensions to ISO 104: bore 75 mm, OD 160 mm, height 69 mm (H1 75 mm installed with the U 415 seat washer); weight 8100 g. Load figures from SKF 17000: dynamic 251 kN, static 610 kN, fatigue limit 20.8 kN; reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53415 M mean?",
        "a": "the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 15 decodes to 75 mm (code 15 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is 53415 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53415",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53415-M",
      "53415 M",
      "53415 M + U 415"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53216",
    "brand": "SKF",
    "manufacturer_designation": "53216",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 80,
    "D_mm": 115,
    "B_mm": 29.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 76.1,
    "static_load_kN": 208,
    "fatigue_load_limit_kN": 7.65,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53216 is an ISO 104 single-direction thrust ball bearing, 80 mm bore and 115 mm OD, with a sphered housing washer and U seat washer, standing 29.5 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 16: bore 80 mm (code 16 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 80×115×29.5 mm (3.15×4.528×1.161 in), 17.5 mm radial section, C 76.1 kN, C0 208 kN, Pu 7.65 kN. Mounted height H1 33 mm includes the U 216 seat washer; the bearing alone is 29.5 mm high. reference speed 2,400 r/min (thermal) and limiting speed 3,200 r/min (mechanical), catalogue mass 1100 g. Pitch-diameter arithmetic: dm = (80+115)/2 = 97.5 mm; at the 3,200 r/min limiting speed that corresponds to roughly 312k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Light-load floor: Pu = 7.65 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 53216; the number is 10 % of the 76.1 kN dynamic rating. Imperial cross-check for procurement drawings: 3.15 in bore, 4.528 in OD, 1.161 in height, and the 1100 g catalogue mass converts to 1.100 kg (38.8 oz). Capacity density: 76.1 kN C from 1.100 kg of bearing steel gives about 69.2 kN per kilogram; static density is correspondingly 189.1 kN/kg at C0 208 kN. Speed band width for this size is 800 r/min between reference and limiting (1.33× ratio); lubrication, preload and heat removal decide where inside that band 53216 can actually run. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53216 and U 216 are two order numbers shipping as two articles; the installed 33 mm H1 rather than 29.5 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "vertical process pumps on welded housings",
      "heavy hook blocks and lifting equipment",
      "marine deck-machinery pivots"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Dimension the housing to the 33 mm mounted height H1 (bearing plus U 216), not the 29.5 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The sphered housing washer of 53216 MUST run against the U 216 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Replacement orders must list both 53216 and U 216: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 208 kN static-rated set.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53216 as the single sphered pressed steel execution; other order numbers of the 53216 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 216 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53216?",
        "a": "The catalogue envelope is 80×115×29.5 mm plus the 3.5 mm the U 216 seat washer adds to reach H1 33 mm, mass 1100 g; ratings C 76.1 kN / C0 208 kN / Pu 7.65 kN, reference speed 2,400 r/min (thermal) and limiting speed 3,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53216 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 16: bore 80 mm (code 16 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "How much misalignment can 53216 accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      },
      {
        "q": "What is the difference between H and H1?",
        "a": "H 29.5 mm is the height of the bearing itself; H1 33 mm is the installed height including the U 216 seat washer. Housing recesses and cover stacks must be drawn to H1, not H."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53216",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53216",
      "53216 + U 216"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53316",
    "brand": "SKF",
    "manufacturer_designation": "53316",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 47.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 159,
    "static_load_kN": 390,
    "fatigue_load_limit_kN": 13.7,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 3200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53316 is an ISO 104 single-direction thrust ball bearing, 80 mm bore and 140 mm OD, with a sphered housing washer and U seat washer, standing 47.6 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 16: bore 80 mm (code 16 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 80×140×47.6 mm (3.15×5.512×1.874 in), 30.0 mm radial section, C 159 kN, C0 390 kN, Pu 13.7 kN. Mounted height H1 52 mm includes the U 316 seat washer; the bearing alone is 47.6 mm high. reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 3200 g. Sizing arithmetic on the 80 mm bore: 159 kN C over the 30.0 mm radial section gives 5.3 kN per section millimetre, and the 47.6 mm stack height is 1.59× that section — proportions typical of a 53300 thrust section. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 2,200 r/min while thermal balance under catalogue load sets the 1,600 r/min reference; at dm ≈ 110.0 mm the corresponding dn is approximately 242k mm·r/min. Minimum-load arithmetic: with dm ≈ 110.0 mm and factor A 0.79, Fam ≈ A·(n·dm/1000)² at the 1,600 r/min reference speed is about 24.5 kN for 53316; below that preload the balls skid and smear the tracks. Stack/annulus proportions: the 47.6 mm axial stack over the 10,367 mm² washer annulus gives 4.59 mm of height per annular square millimetre ×10⁻³, and at 3200 g the bearing holds about 121.9 kN of C0 per kilogram. Envelope economics: the 47.6 mm axial height over a 30.0 mm radial section yields 3.3 kN of dynamic capacity per height millimetre, and the bearing weighs 3200 g for 159 kN C — about 20 g per rated kN. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 140 mm washer can tilt inside the U 316 seat; check the actual tilt allowance in the mounting drawing, since the 4.4 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "winch drums on fabricated structures",
      "vertical process pumps on welded housings",
      "marine deck-machinery pivots"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The shaft washer remains the tight, ground-bore component on the 80 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 316 into the register.",
      "Minimum axial load still applies with factor A 0.79: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "The sphered housing washer of 53316 MUST run against the U 316 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53316 as the single sphered pressed steel execution; other order numbers of the 53316 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 316 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53316?",
        "a": "The catalogue envelope is 80×140×47.6 mm plus the 4.4 mm the U 316 seat washer adds to reach H1 52 mm, mass 3200 g; ratings C 159 kN / C0 390 kN / Pu 13.7 kN, reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53316 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 16: bore 80 mm (code 16 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is the U 316 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53316 and U 316 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      },
      {
        "q": "Is 53316 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53316",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53316",
      "53316 + U 316"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53217",
    "brand": "SKF",
    "manufacturer_designation": "53217",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 85,
    "D_mm": 125,
    "B_mm": 33.1,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 97.5,
    "static_load_kN": 275,
    "fatigue_load_limit_kN": 9,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 1500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 53200 series order number 53217 is a SKF single-direction thrust ball bearing for a 85 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 85×125×33.1 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 17 decodes to 85 mm (code 17 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 85×125×33.1 mm (3.346×4.921×1.303 in), 20.0 mm radial section, C 97.5 kN, C0 275 kN, Pu 9 kN. Mounted height H1 37 mm includes the U 217 seat washer; the bearing alone is 33.1 mm high. reference speed 2,000 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 1500 g. Rating split for documentation: dynamic 97.5 kN (L10 life), static 275 kN (safety factor s0), fatigue limit 9 kN (adjusted life) — three different uses of three different numbers for 53217, none interchangeable with another. Imperial cross-check for procurement drawings: 3.346 in bore, 4.921 in OD, 1.303 in height, and the 1500 g catalogue mass converts to 1.500 kg (52.9 oz). Speed band width for this size is 1,000 r/min between reference and limiting (1.50× ratio); lubrication, preload and heat removal decide where inside that band 53217 can actually run. Washer-stack proportions: the U 217 seat washer adds 3.9 mm to the 33.1 mm bearing height for a mounted H1 of 37 mm, while the 20.0 mm radial section against 85 mm bore (section/bore ≈ 0.24) identifies the envelope. Envelope economics: the 33.1 mm axial height over a 20.0 mm radial section yields 2.9 kN of dynamic capacity per height millimetre, and the bearing weighs 1500 g for 97.5 kN C — about 15 g per rated kN. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 125 mm washer can tilt inside the U 217 seat; check the actual tilt allowance in the mounting drawing, since the 3.9 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "large screw jacks on elastic frames",
      "winch drums on fabricated structures",
      "vertical process pumps on welded housings"
    ],
    "failure_modes": [
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Replacement orders must list both 53217 and U 217: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 275 kN static-rated set.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 217 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "Minimum axial load still applies with factor A 0.39: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The 97.5/275 kN figures belong to 53217 specifically (the single sphered pressed steel execution of 53217); suffixed, sphered and counterpart-series order numbers are separate articles, and U 217 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53217?",
        "a": "Boundary dimensions to ISO 104: bore 85 mm, OD 125 mm, height 33.1 mm (H1 37 mm installed with the U 217 seat washer); weight 1500 g. Load figures from SKF 17000: dynamic 97.5 kN, static 275 kN, fatigue limit 9 kN; reference speed 2,000 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53217 mean?",
        "a": "the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 17 decodes to 85 mm (code 17 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "What is the difference between H and H1?",
        "a": "H 33.1 mm is the height of the bearing itself; H1 37 mm is the installed height including the U 217 seat washer. Housing recesses and cover stacks must be drawn to H1, not H."
      },
      {
        "q": "Why does 53217 need a U 217 seat washer?",
        "a": "The housing washer of 53217 has a sphered back face. The U 217 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53217",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53217",
      "53217 + U 217"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53317",
    "brand": "SKF",
    "manufacturer_designation": "53317",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 53.1,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 174,
    "static_load_kN": 405,
    "fatigue_load_limit_kN": 14,
    "reference_speed_rpm": 1500,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "weight_g": 4350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53317 is SKF's 85 mm-bore single-direction thrust ball bearing in the 53300 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 85×150×53.1 mm U 317 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 17 encode the bore as 85 mm (code 17 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 85×150×53.1 mm (3.346×5.906×2.091 in), 32.5 mm radial section, C 174 kN, C0 405 kN, Pu 14 kN. Mounted height H1 58 mm includes the U 317 seat washer; the bearing alone is 53.1 mm high. reference speed 1,500 r/min (thermal) and limiting speed 2,000 r/min (mechanical), catalogue mass 4350 g. Washer-stack proportions: the U 317 seat washer adds 4.9 mm to the 53.1 mm bearing height for a mounted H1 of 58 mm, while the 32.5 mm radial section against 85 mm bore (section/bore ≈ 0.38) identifies the envelope. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 1.1 at the 2,000 r/min limiting speed raises the required axial preload to about 60.7 kN; the reference-speed value 34.2 kN is the thermal design point. Rating split for documentation: dynamic 174 kN (L10 life), static 405 kN (safety factor s0), fatigue limit 14 kN (adjusted life) — three different uses of three different numbers for 53317, none interchangeable with another. Capacity density: 174 kN C from 4.350 kg of bearing steel gives about 40.0 kN per kilogram; static density is correspondingly 93.1 kN/kg at C0 405 kN. Mass and section check: 4350 g inside the 85×150×53.1 mm outline leaves a 32.5 mm radial section, and the 405 kN static rating is 2.33× the dynamic rating — plan static safety and minimum preload against those figures. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 150 mm washer can tilt inside the U 317 seat; check the actual tilt allowance in the mounting drawing, since the 4.9 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "marine deck-machinery pivots",
      "heavy hook blocks and lifting equipment",
      "winch drums on fabricated structures"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "grease channel failure on a vertical shaft when the upper washer runs dry before the first service interval",
      "corrosion lock of the spherical pair during long outdoor idleness with no preservative grease",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Replacement orders must list both 53317 and U 317: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 405 kN static-rated set.",
      "Dimension the housing to the 58 mm mounted height H1 (bearing plus U 317), not the 53.1 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "The shaft washer remains the tight, ground-bore component on the 85 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 317 into the register.",
      "Ordering discipline for 53317: the catalogue page quotes 53317 plus U 317 and its 174/405 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53317?",
        "a": "53317 measures 85 mm bore × 150 mm OD × 53.1 mm bearing height (3.346 × 5.906 × 2.091 in), or 58 mm mounted H1 including the U 317 seat washer, mass about 4350 g. SKF 17000 ratings: C 174 kN, C0 405 kN, Pu 14 kN, reference speed 1,500 r/min (thermal) and limiting speed 2,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53317 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 17 encode the bore as 85 mm (code 17 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Why does 53317 need a U 317 seat washer?",
        "a": "The housing washer of 53317 has a sphered back face. The U 317 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      },
      {
        "q": "Is the U 317 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53317 and U 317 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53317",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53317",
      "53317 + U 317"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53218",
    "brand": "SKF",
    "manufacturer_designation": "53218",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 90,
    "D_mm": 135,
    "B_mm": 38.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 112,
    "static_load_kN": 290,
    "fatigue_load_limit_kN": 10.4,
    "reference_speed_rpm": 1900,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 2100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53218 is SKF's 90 mm-bore single-direction thrust ball bearing in the 53200 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 90×135×38.5 mm U 218 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 18 encode the bore as 90 mm (code 18 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 90×135×38.5 mm (3.543×5.315×1.516 in), 22.5 mm radial section, C 112 kN, C0 290 kN, Pu 10.4 kN. Mounted height H1 42 mm includes the U 218 seat washer; the bearing alone is 38.5 mm high. reference speed 1,900 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 2100 g. Rating split for documentation: dynamic 112 kN (L10 life), static 290 kN (safety factor s0), fatigue limit 10.4 kN (adjusted life) — three different uses of three different numbers for 53218, none interchangeable with another. Pitch-diameter arithmetic: dm = (90+135)/2 = 112.5 mm; at the 2,600 r/min limiting speed that corresponds to roughly 293k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 2,600 r/min while thermal balance under catalogue load sets the 1,900 r/min reference; at dm ≈ 112.5 mm the corresponding dn is approximately 293k mm·r/min. Load balance: C0 290 kN against C 112 kN gives a 2.59 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 10.4 kN enters the adjusted-life check. Mass and section check: 2100 g inside the 90×135×38.5 mm outline leaves a 22.5 mm radial section, and the 290 kN static rating is 2.59× the dynamic rating — plan static safety and minimum preload against those figures. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53218 and U 218 are two order numbers shipping as two articles; the installed 42 mm H1 rather than 38.5 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "heavy hook blocks and lifting equipment",
      "marine deck-machinery pivots",
      "large screw jacks on elastic frames"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Dimension the housing to the 42 mm mounted height H1 (bearing plus U 218), not the 38.5 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The sphered housing washer of 53218 MUST run against the U 218 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Replacement orders must list both 53218 and U 218: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 290 kN static-rated set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53218 as the single sphered pressed steel execution; other order numbers of the 53218 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 218 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53218?",
        "a": "53218 measures 90 mm bore × 135 mm OD × 38.5 mm bearing height (3.543 × 5.315 × 1.516 in), or 42 mm mounted H1 including the U 218 seat washer, mass about 2100 g. SKF 17000 ratings: C 112 kN, C0 290 kN, Pu 10.4 kN, reference speed 1,900 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53218 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 18 encode the bore as 90 mm (code 18 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Why does 53218 need a U 218 seat washer?",
        "a": "The housing washer of 53218 has a sphered back face. The U 218 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      },
      {
        "q": "Is the U 218 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53218 and U 218 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53218",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53218",
      "53218 + U 218"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53318",
    "brand": "SKF",
    "manufacturer_designation": "53318",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 90,
    "D_mm": 155,
    "B_mm": 54.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 182,
    "static_load_kN": 440,
    "fatigue_load_limit_kN": 14.6,
    "reference_speed_rpm": 1400,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "weight_g": 4700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53318 is an ISO 104 single-direction thrust ball bearing, 90 mm bore and 155 mm OD, with a sphered housing washer and U seat washer, standing 54.6 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 18: bore 90 mm (code 18 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 90×155×54.6 mm (3.543×6.102×2.15 in), 32.5 mm radial section, C 182 kN, C0 440 kN, Pu 14.6 kN. Mounted height H1 59 mm includes the U 318 seat washer; the bearing alone is 54.6 mm high. reference speed 1,400 r/min (thermal) and limiting speed 2,000 r/min (mechanical), catalogue mass 4700 g. Capacity density: 182 kN C from 4.700 kg of bearing steel gives about 38.7 kN per kilogram; static density is correspondingly 93.6 kN/kg at C0 440 kN. At the printed limiting speed of 2,000 r/min the mean pitch diameter dm ≈ 122.5 mm implies a dn value around 245k mm·r/min; the 1,400 r/min reference speed is the thermal-planning value under catalogue load. Sizing arithmetic on the 90 mm bore: 182 kN C over the 32.5 mm radial section gives 5.6 kN per section millimetre, and the 54.6 mm stack height is 1.68× that section — proportions typical of a 53300 thrust section. Pitch-diameter arithmetic: dm = (90+155)/2 = 122.5 mm; at the 2,000 r/min limiting speed that corresponds to roughly 245k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Washer-annulus check: the π/4·(D²−d²) contact annulus of 53318 covers about 12,507 mm², distributing C0 440 kN over a mean track circle of π·dm ≈ 385 mm. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 155 mm washer can tilt inside the U 318 seat; check the actual tilt allowance in the mounting drawing, since the 4.4 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "vertical process pumps on welded housings",
      "marine deck-machinery pivots",
      "heavy hook blocks and lifting equipment"
    ],
    "failure_modes": [
      "cage damage from mounting force applied through the balls instead of the washer face",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Replacement orders must list both 53318 and U 318: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 440 kN static-rated set.",
      "Dimension the housing to the 59 mm mounted height H1 (bearing plus U 318), not the 54.6 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "Minimum axial load still applies with factor A 1.3: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53318 as the single sphered pressed steel execution; other order numbers of the 53318 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 318 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53318?",
        "a": "The catalogue envelope is 90×155×54.6 mm plus the 4.4 mm the U 318 seat washer adds to reach H1 59 mm, mass 4700 g; ratings C 182 kN / C0 440 kN / Pu 14.6 kN, reference speed 1,400 r/min (thermal) and limiting speed 2,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53318 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 18: bore 90 mm (code 18 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is the U 318 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53318 and U 318 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      },
      {
        "q": "Is 53318 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53318",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53318",
      "53318 + U 318"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53418-M",
    "brand": "SKF",
    "manufacturer_designation": "53418 M",
    "series": "53400-series",
    "type": "thrust_ball",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 81.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 307,
    "static_load_kN": 815,
    "fatigue_load_limit_kN": 25.5,
    "reference_speed_rpm": 1100,
    "limiting_speed_rpm": 1500,
    "max_rpm": 1500,
    "weight_g": 13000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53418 M is SKF's 90 mm-bore single-direction thrust ball bearing in the 53400 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 90×190×81.2 mm U 418 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 18 encode the bore as 90 mm (code 18 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 90×190×81.2 mm (3.543×7.48×3.197 in), 50.0 mm radial section, C 307 kN, C0 815 kN, Pu 25.5 kN. Mounted height H1 88 mm includes the U 418 seat washer; the bearing alone is 81.2 mm high. reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical), catalogue mass 13000 g. Washer-stack proportions: the U 418 seat washer adds 6.8 mm to the 81.2 mm bearing height for a mounted H1 of 88 mm, while the 50.0 mm radial section against 90 mm bore (section/bore ≈ 0.56) identifies the envelope. Selection figures for 53418 M: the C0/C ratio is 2.65, Pu 25.5 kN is about 8 % of C, and the catalogue mass works out to roughly 144 g per millimetre of bore; the printed minimum-load factor is A 3.5. Speed band width for this size is 400 r/min between reference and limiting (1.36× ratio); lubrication, preload and heat removal decide where inside that band 53418 M can actually run. At the printed limiting speed of 1,500 r/min the mean pitch diameter dm ≈ 140.0 mm implies a dn value around 210k mm·r/min; the 1,100 r/min reference speed is the thermal-planning value under catalogue load. Pitch-diameter arithmetic: dm = (90+190)/2 = 140.0 mm; at the 1,500 r/min limiting speed that corresponds to roughly 210k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Heavy sphered-execution note: this M order number combines the machined brass ball-centred cage with the sphered housing washer and its U seat washer; it is the large-bore answer for hook blocks and pivots whose fabricated structure deflects — verify the spherical pair swivels freely under a light preload before the working load goes on. The M brass-cage option at 90 mm bore pairs the heavy-section cage with the U 418 seat requirement — order all three articles (bearing + U washer + appropriate lubricant) together, and log the H1 88 mm installed dimension on the maintenance card.",
    "applications": [
      "heavy hook blocks and lifting equipment",
      "large screw jacks on elastic frames",
      "winch drums on fabricated structures"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "edge loading on the ball set when the U seat washer is fitted with its concave face reversed",
      "fretting between the sphered washer and U seat washer when the spherical interface runs dry under oscillation",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The sphered housing washer of 53418 M MUST run against the U 418 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 418 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "Dimension the housing to the 88 mm mounted height H1 (bearing plus U 418), not the 81.2 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "The 307/815 kN figures belong to 53418 M specifically (the single sphered brass execution of 53418); suffixed, sphered and counterpart-series order numbers are separate articles, and U 418 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53418-M?",
        "a": "53418 M measures 90 mm bore × 190 mm OD × 81.2 mm bearing height (3.543 × 7.48 × 3.197 in), or 88 mm mounted H1 including the U 418 seat washer, mass about 13000 g. SKF 17000 ratings: C 307 kN, C0 815 kN, Pu 25.5 kN, reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53418 M mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 18 encode the bore as 90 mm (code 18 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53418-M accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53418",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53418-M",
      "53418 M",
      "53418 M + U 418"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53220",
    "brand": "SKF",
    "manufacturer_designation": "53220",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 100,
    "D_mm": 150,
    "B_mm": 40.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 119,
    "static_load_kN": 325,
    "fatigue_load_limit_kN": 10.8,
    "reference_speed_rpm": 1700,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 2700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 53200 series order number 53220 is a SKF single-direction thrust ball bearing for a 100 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 100×150×40.9 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 20 decodes to 100 mm (code 20 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 100×150×40.9 mm (3.937×5.906×1.61 in), 25.0 mm radial section, C 119 kN, C0 325 kN, Pu 10.8 kN. Mounted height H1 45 mm includes the U 220 seat washer; the bearing alone is 40.9 mm high. reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 2700 g. Stack/annulus proportions: the 40.9 mm axial stack over the 9,817 mm² washer annulus gives 4.17 mm of height per annular square millimetre ×10⁻³, and at 2700 g the bearing holds about 120.4 kN of C0 per kilogram. Speed-ratio note for this exact unit: the reference speed is 1,700 r/min against a 2,400 r/min limiting speed, a reference-to-limit ratio of 0.71. Load balance: C0 325 kN against C 119 kN gives a 2.73 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 10.8 kN enters the adjusted-life check. Washer-stack proportions: the U 220 seat washer adds 4.1 mm to the 40.9 mm bearing height for a mounted H1 of 45 mm, while the 25.0 mm radial section against 100 mm bore (section/bore ≈ 0.25) identifies the envelope. Speed band width for this size is 700 r/min between reference and limiting (1.41× ratio); lubrication, preload and heat removal decide where inside that band 53220 can actually run. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 150 mm washer can tilt inside the U 220 seat; check the actual tilt allowance in the mounting drawing, since the 4.1 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "winch drums on fabricated structures",
      "marine deck-machinery pivots",
      "vertical process pumps on welded housings"
    ],
    "failure_modes": [
      "housing-washer creep and seat fretting where the loose washer is not positively located in its bore",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The shaft washer remains the tight, ground-bore component on the 100 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 220 into the register.",
      "Minimum axial load still applies with factor A 0.62: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "Dimension the housing to the 45 mm mounted height H1 (bearing plus U 220), not the 40.9 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The sphered housing washer of 53220 MUST run against the U 220 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53220 as the single sphered pressed steel execution; other order numbers of the 53220 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 220 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53220?",
        "a": "Boundary dimensions to ISO 104: bore 100 mm, OD 150 mm, height 40.9 mm (H1 45 mm installed with the U 220 seat washer); weight 2700 g. Load figures from SKF 17000: dynamic 119 kN, static 325 kN, fatigue limit 10.8 kN; reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53220 mean?",
        "a": "the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 20 decodes to 100 mm (code 20 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "What is the difference between H and H1?",
        "a": "H 40.9 mm is the height of the bearing itself; H1 45 mm is the installed height including the U 220 seat washer. Housing recesses and cover stacks must be drawn to H1, not H."
      },
      {
        "q": "Why does 53220 need a U 220 seat washer?",
        "a": "The housing washer of 53220 has a sphered back face. The U 220 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53220",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53220",
      "53220 + U 220"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53320",
    "brand": "SKF",
    "manufacturer_designation": "53320",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 100,
    "D_mm": 170,
    "B_mm": 59.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 225,
    "static_load_kN": 570,
    "fatigue_load_limit_kN": 18.3,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "weight_g": 5950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53320 is SKF's 100 mm-bore single-direction thrust ball bearing in the 53300 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 100×170×59.2 mm U 320 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 20 encode the bore as 100 mm (code 20 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 100×170×59.2 mm (3.937×6.693×2.331 in), 35.0 mm radial section, C 225 kN, C0 570 kN, Pu 18.3 kN. Mounted height H1 64 mm includes the U 320 seat washer; the bearing alone is 59.2 mm high. reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical), catalogue mass 5950 g. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 1,800 r/min while thermal balance under catalogue load sets the 1,300 r/min reference; at dm ≈ 135.0 mm the corresponding dn is approximately 243k mm·r/min. Mass and section check: 5950 g inside the 100×170×59.2 mm outline leaves a 35.0 mm radial section, and the 570 kN static rating is 2.53× the dynamic rating — plan static safety and minimum preload against those figures. Rating split for documentation: dynamic 225 kN (L10 life), static 570 kN (safety factor s0), fatigue limit 18.3 kN (adjusted life) — three different uses of three different numbers for 53320, none interchangeable with another. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 1.9 at the 1,800 r/min limiting speed raises the required axial preload to about 112.2 kN; the reference-speed value 58.5 kN is the thermal design point. Capacity density: 225 kN C from 5.950 kg of bearing steel gives about 37.8 kN per kilogram; static density is correspondingly 95.8 kN/kg at C0 570 kN. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 170 mm washer can tilt inside the U 320 seat; check the actual tilt allowance in the mounting drawing, since the 4.8 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "winch drums on fabricated structures",
      "marine deck-machinery pivots",
      "vertical process pumps on welded housings"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "corrosion lock of the spherical pair during long outdoor idleness with no preservative grease",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "The shaft washer remains the tight, ground-bore component on the 100 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 320 into the register.",
      "The sphered housing washer of 53320 MUST run against the U 320 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Replacement orders must list both 53320 and U 320: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 570 kN static-rated set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53320 as the single sphered pressed steel execution; other order numbers of the 53320 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 320 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53320?",
        "a": "53320 measures 100 mm bore × 170 mm OD × 59.2 mm bearing height (3.937 × 6.693 × 2.331 in), or 64 mm mounted H1 including the U 320 seat washer, mass about 5950 g. SKF 17000 ratings: C 225 kN, C0 570 kN, Pu 18.3 kN, reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53320 mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 20 encode the bore as 100 mm (code 20 × 5), the standard SKF bore-code rule shared with radial bearings. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Why does 53320 need a U 320 seat washer?",
        "a": "The housing washer of 53320 has a sphered back face. The U 320 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      },
      {
        "q": "Is the U 320 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53320 and U 320 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53320",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53320",
      "53320 + U 320"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53420-M",
    "brand": "SKF",
    "manufacturer_designation": "53420 M",
    "series": "53400-series",
    "type": "thrust_ball",
    "d_mm": 100,
    "D_mm": 210,
    "B_mm": 90,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 371,
    "static_load_kN": 1060,
    "fatigue_load_limit_kN": 31.5,
    "reference_speed_rpm": 950,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "weight_g": 18000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53420 M is SKF's 100 mm-bore single-direction thrust ball bearing in the 53400 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 100×210×90 mm U 420 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 20 encode the bore as 100 mm (code 20 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 100×210×90 mm (3.937×8.268×3.543 in), 55.0 mm radial section, C 371 kN, C0 1060 kN, Pu 31.5 kN. Mounted height H1 98 mm includes the U 420 seat washer; the bearing alone is 90 mm high. reference speed 950 r/min (thermal) and limiting speed 1,300 r/min (mechanical), catalogue mass 18000 g. Stack/annulus proportions: the 90 mm axial stack over the 26,782 mm² washer annulus gives 3.36 mm of height per annular square millimetre ×10⁻³, and at 18000 g the bearing holds about 58.9 kN of C0 per kilogram. Load balance: C0 1060 kN against C 371 kN gives a 2.86 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 31.5 kN enters the adjusted-life check. Selection figures for 53420 M: the C0/C ratio is 2.86, Pu 31.5 kN is about 8 % of C, and the catalogue mass works out to roughly 180 g per millimetre of bore; the printed minimum-load factor is A 5.8. Sizing arithmetic on the 100 mm bore: 371 kN C over the 55.0 mm radial section gives 6.7 kN per section millimetre, and the 90 mm stack height is 1.64× that section — proportions typical of a 53400 thrust section. Speed-ratio note for this exact unit: the reference speed is 950 r/min against a 1,300 r/min limiting speed, a reference-to-limit ratio of 0.73. Heavy sphered-execution note: this M order number combines the machined brass ball-centred cage with the sphered housing washer and its U seat washer; it is the large-bore answer for hook blocks and pivots whose fabricated structure deflects — verify the spherical pair swivels freely under a light preload before the working load goes on. The M brass-cage option at 100 mm bore pairs the heavy-section cage with the U 420 seat requirement — order all three articles (bearing + U washer + appropriate lubricant) together, and log the H1 98 mm installed dimension on the maintenance card.",
    "applications": [
      "large screw jacks on elastic frames",
      "vertical process pumps on welded housings",
      "winch drums on fabricated structures"
    ],
    "failure_modes": [
      "ball skidding and track smearing once the applied thrust falls below the catalogue minimum axial load at high speed",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "fretting between the sphered washer and U seat washer when the spherical interface runs dry under oscillation",
      "track rust staining from condensate during long idle periods in humid plant air",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Dimension the housing to the 98 mm mounted height H1 (bearing plus U 420), not the 90 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The sphered housing washer of 53420 M MUST run against the U 420 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Replacement orders must list both 53420 M and U 420: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 1060 kN static-rated set.",
      "The 371/1060 kN figures belong to 53420 M specifically (the single sphered brass execution of 53420); suffixed, sphered and counterpart-series order numbers are separate articles, and U 420 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53420-M?",
        "a": "53420 M measures 100 mm bore × 210 mm OD × 90 mm bearing height (3.937 × 8.268 × 3.543 in), or 98 mm mounted H1 including the U 420 seat washer, mass about 18000 g. SKF 17000 ratings: C 371 kN, C0 1060 kN, Pu 31.5 kN, reference speed 950 r/min (thermal) and limiting speed 1,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53420 M mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 20 encode the bore as 100 mm (code 20 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Why does 53420-M need a U 420 seat washer?",
        "a": "The housing washer of 53420 M has a sphered back face. The U 420 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      },
      {
        "q": "Is the U 420 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53420 M and U 420 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53420",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53420-M",
      "53420 M",
      "53420 M + U 420"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53222",
    "brand": "SKF",
    "manufacturer_designation": "53222",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 110,
    "D_mm": 160,
    "B_mm": 40.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 125,
    "static_load_kN": 365,
    "fatigue_load_limit_kN": 11.6,
    "reference_speed_rpm": 1700,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 2900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 53200 series order number 53222 is a SKF single-direction thrust ball bearing for a 110 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 110×160×40.2 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 22 decodes to 110 mm (code 22 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 110×160×40.2 mm (4.331×6.299×1.583 in), 25.0 mm radial section, C 125 kN, C0 365 kN, Pu 11.6 kN. Mounted height H1 45 mm includes the U 222 seat washer; the bearing alone is 40.2 mm high. reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 2900 g. Selection figures for 53222: the C0/C ratio is 2.92, Pu 11.6 kN is about 9 % of C, and the catalogue mass works out to roughly 26 g per millimetre of bore; the printed minimum-load factor is A 0.79. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 2,400 r/min while thermal balance under catalogue load sets the 1,700 r/min reference; at dm ≈ 135.0 mm the corresponding dn is approximately 324k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 1,700 r/min against a 2,400 r/min limiting speed, a reference-to-limit ratio of 0.71. Sizing arithmetic on the 110 mm bore: 125 kN C over the 25.0 mm radial section gives 5.0 kN per section millimetre, and the 40.2 mm stack height is 1.61× that section — proportions typical of a 53200 thrust section. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.79 at the 2,400 r/min limiting speed raises the required axial preload to about 82.9 kN; the reference-speed value 41.6 kN is the thermal design point. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53222 and U 222 are two order numbers shipping as two articles; the installed 45 mm H1 rather than 40.2 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "winch drums on fabricated structures",
      "vertical process pumps on welded housings",
      "marine deck-machinery pivots"
    ],
    "failure_modes": [
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "corrosion lock of the spherical pair during long outdoor idleness with no preservative grease",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Replacement orders must list both 53222 and U 222: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 365 kN static-rated set.",
      "Dimension the housing to the 45 mm mounted height H1 (bearing plus U 222), not the 40.2 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 222 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The shaft washer remains the tight, ground-bore component on the 110 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 222 into the register.",
      "Ordering discipline for 53222: the catalogue page quotes 53222 plus U 222 and its 125/365 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53222?",
        "a": "Boundary dimensions to ISO 104: bore 110 mm, OD 160 mm, height 40.2 mm (H1 45 mm installed with the U 222 seat washer); weight 2900 g. Load figures from SKF 17000: dynamic 125 kN, static 365 kN, fatigue limit 11.6 kN; reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53222 mean?",
        "a": "the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 22 decodes to 110 mm (code 22 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "What is the difference between H and H1?",
        "a": "H 40.2 mm is the height of the bearing itself; H1 45 mm is the installed height including the U 222 seat washer. Housing recesses and cover stacks must be drawn to H1, not H."
      },
      {
        "q": "Why does 53222 need a U 222 seat washer?",
        "a": "The housing washer of 53222 has a sphered back face. The U 222 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53222",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53222",
      "53222 + U 222"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53322-M",
    "brand": "SKF",
    "manufacturer_designation": "53322 M",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 110,
    "D_mm": 190,
    "B_mm": 67.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 281,
    "static_load_kN": 815,
    "fatigue_load_limit_kN": 24.5,
    "reference_speed_rpm": 1100,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "weight_g": 9100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53322 M is SKF's 110 mm-bore single-direction thrust ball bearing in the 53300 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 110×190×67.2 mm U 322 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 22 encode the bore as 110 mm (code 22 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 110×190×67.2 mm (4.331×7.48×2.646 in), 40.0 mm radial section, C 281 kN, C0 815 kN, Pu 24.5 kN. Mounted height H1 72 mm includes the U 322 seat washer; the bearing alone is 67.2 mm high. reference speed 1,100 r/min (thermal) and limiting speed 1,600 r/min (mechanical), catalogue mass 9100 g. Selection figures for 53322 M: the C0/C ratio is 2.90, Pu 24.5 kN is about 9 % of C, and the catalogue mass works out to roughly 83 g per millimetre of bore; the printed minimum-load factor is A 3.2. Static-first selection data: 815 kN C0 spread across the 67.2 mm stack gives 12.1 kN of static rating per height millimetre, and the 9100 g mass/C0 ratio is about 11 g per static kN — crane-hook and screw positions are normally sized on these two figures. At the printed limiting speed of 1,600 r/min the mean pitch diameter dm ≈ 150.0 mm implies a dn value around 240k mm·r/min; the 1,100 r/min reference speed is the thermal-planning value under catalogue load. Rating split for documentation: dynamic 281 kN (L10 life), static 815 kN (safety factor s0), fatigue limit 24.5 kN (adjusted life) — three different uses of three different numbers for 53322 M, none interchangeable with another. Pitch-diameter arithmetic: dm = (110+190)/2 = 150.0 mm; at the 1,600 r/min limiting speed that corresponds to roughly 240k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Heavy sphered-execution note: this M order number combines the machined brass ball-centred cage with the sphered housing washer and its U seat washer; it is the large-bore answer for hook blocks and pivots whose fabricated structure deflects — verify the spherical pair swivels freely under a light preload before the working load goes on. The M brass-cage option at 110 mm bore pairs the heavy-section cage with the U 322 seat requirement — order all three articles (bearing + U washer + appropriate lubricant) together, and log the H1 72 mm installed dimension on the maintenance card.",
    "applications": [
      "heavy hook blocks and lifting equipment",
      "vertical process pumps on welded housings",
      "large screw jacks on elastic frames"
    ],
    "failure_modes": [
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "raceway spalling when reversing axial force is applied to a single-direction bearing and the unloaded washer lifts off its track",
      "fretting corrosion in the spherical interface under oscillation with no grease between washer and seat",
      "fretting between the sphered washer and U seat washer when the spherical interface runs dry under oscillation",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The sphered housing washer of 53322 M MUST run against the U 322 seat washer, a separate order number; mounted bare on a flat register, the convex back makes point contact that gouges the housing under load.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 322 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "Dimension the housing to the 72 mm mounted height H1 (bearing plus U 322), not the 67.2 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "The 281/815 kN figures belong to 53322 M specifically (the single sphered brass execution of 53322); suffixed, sphered and counterpart-series order numbers are separate articles, and U 322 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53322-M?",
        "a": "53322 M measures 110 mm bore × 190 mm OD × 67.2 mm bearing height (4.331 × 7.48 × 2.646 in), or 72 mm mounted H1 including the U 322 seat washer, mass about 9100 g. SKF 17000 ratings: C 281 kN, C0 815 kN, Pu 24.5 kN, reference speed 1,100 r/min (thermal) and limiting speed 1,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53322 M mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 22 encode the bore as 110 mm (code 22 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53322-M accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53322",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53322-M",
      "53322 M",
      "53322 M + U 322"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53224",
    "brand": "SKF",
    "manufacturer_designation": "53224",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 120,
    "D_mm": 170,
    "B_mm": 40.8,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 127,
    "static_load_kN": 390,
    "fatigue_load_limit_kN": 11.8,
    "reference_speed_rpm": 1500,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 3200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53224 is an ISO 104 single-direction thrust ball bearing, 120 mm bore and 170 mm OD, with a sphered housing washer and U seat washer, standing 40.8 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 24: bore 120 mm (code 24 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 120×170×40.8 mm (4.724×6.693×1.606 in), 25.0 mm radial section, C 127 kN, C0 390 kN, Pu 11.8 kN. Mounted height H1 46 mm includes the U 224 seat washer; the bearing alone is 40.8 mm high. reference speed 1,500 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 3200 g. Selection figures for 53224: the C0/C ratio is 3.07, Pu 11.8 kN is about 9 % of C, and the catalogue mass works out to roughly 27 g per millimetre of bore; the printed minimum-load factor is A 1. Static-first selection data: 390 kN C0 spread across the 40.8 mm stack gives 9.6 kN of static rating per height millimetre, and the 3200 g mass/C0 ratio is about 8 g per static kN — crane-hook and screw positions are normally sized on these two figures. Washer-stack proportions: the U 224 seat washer adds 5.2 mm to the 40.8 mm bearing height for a mounted H1 of 46 mm, while the 25.0 mm radial section against 120 mm bore (section/bore ≈ 0.21) identifies the envelope. Mass and section check: 3200 g inside the 120×170×40.8 mm outline leaves a 25.0 mm radial section, and the 390 kN static rating is 3.07× the dynamic rating — plan static safety and minimum preload against those figures. Washer-annulus check: the π/4·(D²−d²) contact annulus of 53224 covers about 11,388 mm², distributing C0 390 kN over a mean track circle of π·dm ≈ 456 mm. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53224 and U 224 are two order numbers shipping as two articles; the installed 46 mm H1 rather than 40.8 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "offshore deck-machinery seats",
      "heavy dredge and excavator pivot thrusts",
      "ship-lift and gate winch drums"
    ],
    "failure_modes": [
      "pitting on one track sector from a perpetually eccentric thrust line",
      "thermal smearing after the loose housing washer is clamped solid and cannot slide with growth",
      "edge loading on the ball set when the U seat washer is fitted with its concave face reversed",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Minimum axial load still applies with factor A 1: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "The shaft washer remains the tight, ground-bore component on the 120 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 224 into the register.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53224 as the single sphered pressed steel execution; other order numbers of the 53224 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 224 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53224?",
        "a": "The catalogue envelope is 120×170×40.8 mm plus the 5.2 mm the U 224 seat washer adds to reach H1 46 mm, mass 3200 g; ratings C 127 kN / C0 390 kN / Pu 11.8 kN, reference speed 1,500 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53224 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 24: bore 120 mm (code 24 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is the U 224 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53224 and U 224 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      },
      {
        "q": "Is 53224 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53224",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53224",
      "53224 + U 224"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53324-M",
    "brand": "SKF",
    "manufacturer_designation": "53324 M",
    "series": "53300-series",
    "type": "thrust_ball",
    "d_mm": 120,
    "D_mm": 210,
    "B_mm": 74.1,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 325,
    "static_load_kN": 980,
    "fatigue_load_limit_kN": 28.5,
    "reference_speed_rpm": 1000,
    "limiting_speed_rpm": 1400,
    "max_rpm": 1400,
    "weight_g": 12500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "53324 M is SKF's 120 mm-bore single-direction thrust ball bearing in the 53300 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 120×210×74.1 mm U 324 seat washer companion included in the mounted H1 dimension. The separable set comprises a shaft washer (ground bore, tight fit on the shaft), a loose-bore housing washer and one ball-cage assembly, reacting axial force in one direction and carrying no radial load. in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 24 encode the bore as 120 mm (code 24 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 120×210×74.1 mm (4.724×8.268×2.917 in), 45.0 mm radial section, C 325 kN, C0 980 kN, Pu 28.5 kN. Mounted height H1 80 mm includes the U 324 seat washer; the bearing alone is 74.1 mm high. reference speed 1,000 r/min (thermal) and limiting speed 1,400 r/min (mechanical), catalogue mass 12500 g. Stack/annulus proportions: the 74.1 mm axial stack over the 23,326 mm² washer annulus gives 3.18 mm of height per annular square millimetre ×10⁻³, and at 12500 g the bearing holds about 78.4 kN of C0 per kilogram. Selection figures for 53324 M: the C0/C ratio is 3.02, Pu 28.5 kN is about 9 % of C, and the catalogue mass works out to roughly 104 g per millimetre of bore; the printed minimum-load factor is A 5. Sizing arithmetic on the 120 mm bore: 325 kN C over the 45.0 mm radial section gives 7.2 kN per section millimetre, and the 74.1 mm stack height is 1.65× that section — proportions typical of a 53300 thrust section. Bore-to-OD planning: OD 210 over bore 120 is a 1.75× step for this size, and the 74.1 mm height gives a bore/height ratio of 1.62; use these ratios when the housing recess around the 120 mm shaft is the first constraint. Speed planning separates the two ceilings mechanically: the pressed brass cage and balls tolerate 1,400 r/min while thermal balance under catalogue load sets the 1,000 r/min reference; at dm ≈ 165.0 mm the corresponding dn is approximately 231k mm·r/min. Heavy sphered-execution note: this M order number combines the machined brass ball-centred cage with the sphered housing washer and its U seat washer; it is the large-bore answer for hook blocks and pivots whose fabricated structure deflects — verify the spherical pair swivels freely under a light preload before the working load goes on. Under 980 kN static load the spherical interface of 53324 M must stay lubricated with a grease that does not separate at rest; a dry sphered contact under hook-block shock frets even though the ball tracks remain unworn.",
    "applications": [
      "offshore deck-machinery seats",
      "heavy dredge and excavator pivot thrusts",
      "ship-lift and gate winch drums"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "brinell marks on the shaft-washer track from a static thrust shock beyond the C0 rating",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "fretting between the sphered washer and U seat washer when the spherical interface runs dry under oscillation",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "Replacement orders must list both 53324 M and U 324: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 980 kN static-rated set.",
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 324 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "Minimum axial load still applies with factor A 5: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "Ordering discipline for 53324: the catalogue page quotes 53324 M plus U 324 and its 325/980 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53324-M?",
        "a": "53324 M measures 120 mm bore × 210 mm OD × 74.1 mm bearing height (4.724 × 8.268 × 2.917 in), or 80 mm mounted H1 including the U 324 seat washer, mass about 12500 g. SKF 17000 ratings: C 325 kN, C0 980 kN, Pu 28.5 kN, reference speed 1,000 r/min (thermal) and limiting speed 1,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53324 M mean?",
        "a": "in the 53xxx designation the 3 marks a single-direction bearing whose housing washer has a sphered (convex) seating surface, intended to run against the matching U seat washer; the third digit 2–4 grades the section. the final two digits 24 encode the bore as 120 mm (code 24 × 5), the standard SKF bore-code rule shared with radial bearings. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Can I run the 53-series bearing without the U washer on a flat face?",
        "a": "No — that makes point contact between the sphered back and the register, gouging the housing and tilting the ball set under load. If no misalignment exists, use the cheaper flat-seat 51-series bearing of the corresponding section instead."
      },
      {
        "q": "How much misalignment can 53324-M accommodate?",
        "a": "The spherical seat accommodates initial STATIC misalignment between shaft and housing at mounting; it is not designed for continuous oscillation or dynamic shaft deflection, and it does not add radial capacity — the load remains purely axial."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53324",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53324-M",
      "53324 M",
      "53324 M + U 324"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53226",
    "brand": "SKF",
    "manufacturer_designation": "53226",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 130,
    "D_mm": 190,
    "B_mm": 47.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 186,
    "static_load_kN": 585,
    "fatigue_load_limit_kN": 17,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "weight_g": 4850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 53200 series order number 53226 is a SKF single-direction thrust ball bearing for a 130 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 130×190×47.9 mm boundary dimensions. Three separable parts make the set: the tight-bore shaft washer that locates on the shaft, the loose-bore housing washer in its register, and the ball-cage assembly; load is purely axial and acts in one direction. the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 26 decodes to 130 mm (code 26 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 130×190×47.9 mm (5.118×7.48×1.886 in), 30.0 mm radial section, C 186 kN, C0 585 kN, Pu 17 kN. Mounted height H1 53 mm includes the U 226 seat washer; the bearing alone is 47.9 mm high. reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical), catalogue mass 4850 g. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 1,800 r/min while thermal balance under catalogue load sets the 1,300 r/min reference; at dm ≈ 160.0 mm the corresponding dn is approximately 288k mm·r/min. Selection figures for 53226: the C0/C ratio is 3.15, Pu 17 kN is about 9 % of C, and the catalogue mass works out to roughly 37 g per millimetre of bore; the printed minimum-load factor is A 1.8. Bore-to-OD planning: OD 190 over bore 130 is a 1.46× step for this size, and the 47.9 mm height gives a bore/height ratio of 2.71; use these ratios when the housing recess around the 130 mm shaft is the first constraint. Capacity density: 186 kN C from 4.850 kg of bearing steel gives about 38.4 kN per kilogram; static density is correspondingly 120.6 kN/kg at C0 585 kN. Track-circle loading: per millimetre of mean track circumference the 186 kN dynamic rating corresponds to roughly 0.37 kN/mm of π·dm track, a useful comparison against the other dimension series of the 130 mm bore. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. Procurement reminder for this specific page: 53226 and U 226 are two order numbers shipping as two articles; the installed 53 mm H1 rather than 47.9 mm H is the dimension the housing drawing must carry.",
    "applications": [
      "ladle and slag-pot hooks in steelworks",
      "ship-lift and gate winch drums",
      "offshore deck-machinery seats"
    ],
    "failure_modes": [
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "pitting on one track sector from a perpetually eccentric thrust line",
      "corrosion lock of the spherical pair during long outdoor idleness with no preservative grease",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Replacement orders must list both 53226 and U 226: the seat washer is a separate article, and a U washer of the wrong size narrows the contact band of the 585 kN static-rated set.",
      "Dimension the housing to the 53 mm mounted height H1 (bearing plus U 226), not the 47.9 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "The self-aligning feature is checked at commissioning by hand: with the shaft under no load the assembly must swivel and settle; a stiff spherical seat means dirt, a mismatched U washer, or a register bored off-axis.",
      "The shaft washer remains the tight, ground-bore component on the 130 mm shaft; the sphered part is the HOUSING washer, and the U seat washer is the loose flat-backed part — the fitting order is shaft washer and cage set first, then housing washer and U 226 into the register.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53226 as the single sphered pressed steel execution; other order numbers of the 53226 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 226 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53226?",
        "a": "Boundary dimensions to ISO 104: bore 130 mm, OD 190 mm, height 47.9 mm (H1 53 mm installed with the U 226 seat washer); weight 4850 g. Load figures from SKF 17000: dynamic 186 kN, static 585 kN, fatigue limit 17 kN; reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53226 mean?",
        "a": "the 3 in 53xxx replaces the flat-seat 1: it still denotes one load direction, but the housing washer is sphered for pairing with a U seat washer, and the following digit 2–4 ranks the section. bore code 26 decodes to 130 mm (code 26 × 5) under the same 00/01/02/03-exception, ×5 rule SKF uses across its coded bearing ranges. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "What is the difference between H and H1?",
        "a": "H 47.9 mm is the height of the bearing itself; H1 53 mm is the installed height including the U 226 seat washer. Housing recesses and cover stacks must be drawn to H1, not H."
      },
      {
        "q": "Why does 53226 need a U 226 seat washer?",
        "a": "The housing washer of 53226 has a sphered back face. The U 226 seat washer presents a matching concave face plus a flat housing face, and without it the convex washer contacts the register at a single point; the pair is what gives the bearing its initial-misalignment capacity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53226",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53226",
      "53226 + U 226"
    ],
    "locale_variants": {}
  },
  {
    "sku": "53228",
    "brand": "SKF",
    "manufacturer_designation": "53228",
    "series": "53200-series",
    "type": "thrust_ball",
    "d_mm": 140,
    "D_mm": 200,
    "B_mm": 48.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 190,
    "static_load_kN": 620,
    "fatigue_load_limit_kN": 17.6,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "weight_g": 5450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 53228 is an ISO 104 single-direction thrust ball bearing, 140 mm bore and 200 mm OD, with a sphered housing washer and U seat washer, standing 48.6 mm high before installation. The bearing is delivered as separate, interchangeable parts: a ground-bore shaft washer, a loose-bore housing washer and the ball-cage assembly between them, designed for one axial load direction only. 53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 28: bore 140 mm (code 28 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 140×200×48.6 mm (5.512×7.874×1.913 in), 30.0 mm radial section, C 190 kN, C0 620 kN, Pu 17.6 kN. Mounted height H1 55 mm includes the U 228 seat washer; the bearing alone is 48.6 mm high. reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical), catalogue mass 5450 g. Minimum-load arithmetic: with dm ≈ 170.0 mm and factor A 2, Fam ≈ A·(n·dm/1000)² at the 1,300 r/min reference speed is about 97.7 kN for 53228; below that preload the balls skid and smear the tracks. Washer-annulus check: the π/4·(D²−d²) contact annulus of 53228 covers about 16,022 mm², distributing C0 620 kN over a mean track circle of π·dm ≈ 534 mm. Mass and section check: 5450 g inside the 140×200×48.6 mm outline leaves a 30.0 mm radial section, and the 620 kN static rating is 3.26× the dynamic rating — plan static safety and minimum preload against those figures. Sizing arithmetic on the 140 mm bore: 190 kN C over the 30.0 mm radial section gives 6.3 kN per section millimetre, and the 48.6 mm stack height is 1.62× that section — proportions typical of a 53200 thrust section. Washer-stack proportions: the U 228 seat washer adds 6.4 mm to the 48.6 mm bearing height for a mounted H1 of 55 mm, while the 30.0 mm radial section against 140 mm bore (section/bore ≈ 0.21) identifies the envelope. Sphered-seating order-number note: the convex back face of the housing washer is finish-ground spherical and is delivered to mate with the separately ordered U seat washer, which presents a flat face to the housing and a concave face to the washer; together they accommodate initial static misalignment, but the pair must be kept clean, greased at the spherical interface and never replaced by a washer-on-flat-steel makeshift. The aligning angle is set by how far the sphered back of the 200 mm washer can tilt inside the U 228 seat; check the actual tilt allowance in the mounting drawing, since the 6.4 mm washer thickness step does not by itself quantify it.",
    "applications": [
      "ladle and slag-pot hooks in steelworks",
      "offshore deck-machinery seats",
      "ship-lift and gate winch drums"
    ],
    "failure_modes": [
      "ball-set launch and loss when the separable bearing is lifted out of the housing without retaining the cage",
      "edge loading across the ball set when the housing shoulder is not square to the shaft axis",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "point-contact gouging of the housing face when the sphered washer is run without its U seat washer",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "track rust staining from condensate during long idle periods in humid plant air"
    ],
    "pitfalls": [
      "Keep the sphered interface clean and lightly greased: scale, paint or grit between the washer back and U 228 locks the aligning function and frets under load; re-grease the contact at every overhaul.",
      "The spherical seat accommodates INITIAL static misalignment between shaft and housing; it is not a swivel for continuous oscillation, and the bearing still carries pure axial load with no radial capacity.",
      "Dimension the housing to the 55 mm mounted height H1 (bearing plus U 228), not the 48.6 mm bearing height H — confusing the two is a recurring drawing error for the 53-series.",
      "Minimum axial load still applies with factor A 2: a self-aligning seat does not prevent ball skidding, so provide spring preload or sufficient rotor weight at light load and speed.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 53228 as the single sphered pressed steel execution; other order numbers of the 53228 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 228 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 53228?",
        "a": "The catalogue envelope is 140×200×48.6 mm plus the 6.4 mm the U 228 seat washer adds to reach H1 55 mm, mass 5450 g; ratings C 190 kN / C0 620 kN / Pu 17.6 kN, reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 53228 mean?",
        "a": "53xxx reads as 5 (thrust ball), 3 (single direction with a sphered housing washer), a 2–4 section digit and the bore code; the U seat washer companion carries the matching three-digit number. reading the ending 28: bore 140 mm (code 28 × 5) for this single-direction size, via the standard exceptions 00/01/02/03 and ×5 above them. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 3 = single direction with sphered seating surface."
      },
      {
        "q": "Is the U 228 seat washer supplied in the box?",
        "a": "The U seat washer is a separate order number: 53228 and U 228 are specified independently, so quote both on the purchase order — a sphered bearing without its matched seat cannot be installed correctly."
      },
      {
        "q": "Is 53228 bidirectional?",
        "a": "No, the 53-series is single-direction; for reversing thrust with the same self-aligning feature use the 54-series double-direction execution, which needs two U seat washers."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "53228",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "53228",
      "53228 + U 228"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52202",
    "brand": "SKF",
    "manufacturer_designation": "52202",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 10,
    "D_mm": 32,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 15.9,
    "static_load_kN": 25,
    "fatigue_load_limit_kN": 0.915,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 81,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52202 is SKF's 10 mm-bore double-direction thrust ball bearing in the 52200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 10×32×22 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 10 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 10×32×22 mm (0.394×1.26×0.866 in), 11.0 mm radial section, C 15.9 kN, C0 25 kN, Pu 0.915 kN. reference speed 5,300 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 81 g. Light-load floor: Pu = 0.915 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52202; the number is 6 % of the 15.9 kN dynamic rating. Envelope economics: the 22 mm axial height over a 11.0 mm radial section yields 0.7 kN of dynamic capacity per height millimetre, and the bearing weighs 81 g for 15.9 kN C — about 5 g per rated kN. Speed band width for this size is 2,200 r/min between reference and limiting (1.42× ratio); lubrication, preload and heat removal decide where inside that band 52202 can actually run. Minimum-load arithmetic: with dm ≈ 21.0 mm and factor A 0.0038, Fam ≈ A·(n·dm/1000)² at the 5,300 r/min reference speed is about 47 N for 52202; below that preload the balls skid and smear the tracks. Bore-to-OD planning: OD 32 over bore 10 is a 3.20× step for this size, and the 22 mm height gives a bore/height ratio of 0.45; use these ratios when the housing recess around the 10 mm shaft is the first constraint. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52202 is done separately per direction: if duty applies 15.9 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "small gear-selector and detent mechanisms",
      "reversing screw and cam spindles",
      "bidirectional thrust on small vertical shafts"
    ],
    "failure_modes": [
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 7,500 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 25 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 22 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "Do not replace a 52202 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 10×32 mm bore and OD.",
      "The 15.9/25 kN figures belong to 52202 specifically (the double flat pressed steel execution of 52202); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52202?",
        "a": "52202 measures 10 mm bore × 32 mm OD × 22 mm bearing height (0.394 × 1.26 × 0.866 in), mass about 81 g. SKF 17000 ratings: C 15.9 kN, C0 25 kN, Pu 0.915 kN, reference speed 5,300 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52202 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 10 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is the double-direction 52202 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 10×32×22 mm unit locating the shaft axially in both directions."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52202",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52202"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52204",
    "brand": "SKF",
    "manufacturer_designation": "52204",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 15,
    "D_mm": 40,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 21.2,
    "static_load_kN": 37.5,
    "fatigue_load_limit_kN": 1.4,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52204 is SKF's 15 mm-bore double-direction thrust ball bearing in the 52200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 15×40×26 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 15 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 15×40×26 mm (0.591×1.575×1.024 in), 12.5 mm radial section, C 21.2 kN, C0 37.5 kN, Pu 1.4 kN. reference speed 4,300 r/min (thermal) and limiting speed 6,000 r/min (mechanical), catalogue mass 150 g. Stack/annulus proportions: the 26 mm axial stack over the 1,080 mm² washer annulus gives 24.07 mm of height per annular square millimetre ×10⁻³, and at 150 g the bearing holds about 250.0 kN of C0 per kilogram. Washer-annulus check: the π/4·(D²−d²) contact annulus of 52204 covers about 1,080 mm², distributing C0 37.5 kN over a mean track circle of π·dm ≈ 86 mm. Minimum-load arithmetic: with dm ≈ 27.5 mm and factor A 0.0085, Fam ≈ A·(n·dm/1000)² at the 4,300 r/min reference speed is about 119 N for 52204; below that preload the balls skid and smear the tracks. Section proportions: the 12.5 mm radial section compares with 15 mm of bore (section/bore ≈ 0.83) and the 26 mm height is 2.08× that section — the proportions that identify the 52200 envelope at a glance. Speed band width for this size is 1,700 r/min between reference and limiting (1.40× ratio); lubrication, preload and heat removal decide where inside that band 52204 can actually run. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52204 is done separately per direction: if duty applies 21.2 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "office-machine reversal pivots",
      "bidirectional thrust on small vertical shafts",
      "reversing screw and cam spindles"
    ],
    "failure_modes": [
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Do not replace a 52204 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 15×40 mm bore and OD.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 6,000 r/min even a small thermal thrust preload smears the hottest track.",
      "The double-direction 52204 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 15 mm shaft axially in both directions instead of a mirrored pair.",
      "The 21.2/37.5 kN figures belong to 52204 specifically (the double flat pressed steel execution of 52204); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52204?",
        "a": "52204 measures 15 mm bore × 40 mm OD × 26 mm bearing height (0.591 × 1.575 × 1.024 in), mass about 150 g. SKF 17000 ratings: C 21.2 kN, C0 37.5 kN, Pu 1.4 kN, reference speed 4,300 r/min (thermal) and limiting speed 6,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52204 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 15 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "Can it replace two single-direction 51-series bearings?",
        "a": "It replaces a mirrored pair functionally — one fit, one housing bore, factory-matched geometry — but its 26 mm height is not twice the single-bearing height and seat details differ, so the housing and cover must be re-drawn rather than swapped in place."
      },
      {
        "q": "How is a vertical double-direction 52204 lubricated and retained?",
        "a": "Use an oil bath reaching the lower track plus a feed or oil level that serves the upper cage set, or a coherent heavy-base grease; positively retain both loose housing washers because gravity loads the upper stack differently at standstill."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52204",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52204"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52205",
    "brand": "SKF",
    "manufacturer_designation": "52205",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 50,
    "fatigue_load_limit_kN": 1.86,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 52200 series order number 52205 is a SKF double-direction thrust ball bearing for a 20 mm seat, built to ISO 104, with a flat housing seating surface, 20×47×28 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 20 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 20×47×28 mm (0.787×1.85×1.102 in), 13.5 mm radial section, C 26.5 kN, C0 50 kN, Pu 1.86 kN. reference speed 3,800 r/min (thermal) and limiting speed 5,300 r/min (mechanical), catalogue mass 220 g. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 5,300 r/min while thermal balance under catalogue load sets the 3,800 r/min reference; at dm ≈ 33.5 mm the corresponding dn is approximately 178k mm·r/min. Light-load floor: Pu = 1.86 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52205; the number is 7 % of the 26.5 kN dynamic rating. Load balance: C0 50 kN against C 26.5 kN gives a 1.89 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 1.86 kN enters the adjusted-life check. Capacity density: 26.5 kN C from 0.220 kg of bearing steel gives about 120.5 kN per kilogram; static density is correspondingly 227.3 kN/kg at C0 50 kN. Pitch-diameter arithmetic: dm = (20+47)/2 = 33.5 mm; at the 5,300 r/min limiting speed that corresponds to roughly 178k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52205 is done separately per direction: if duty applies 26.5 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "office-machine reversal pivots",
      "reversing screw and cam spindles",
      "bidirectional thrust on small vertical shafts"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "cover-induced thrust preload when the end cover is torqued solid instead of leaving the catalogue axial freedom",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Do not replace a 52205 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 20×47 mm bore and OD.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 5,300 r/min even a small thermal thrust preload smears the hottest track.",
      "The double-direction 52205 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 20 mm shaft axially in both directions instead of a mirrored pair.",
      "The central shaft washer takes the interference fit on the 20 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52205 as the double flat pressed steel execution; other order numbers of the 52205 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52205?",
        "a": "Boundary dimensions to ISO 104: bore 20 mm, OD 47 mm, height 28 mm; weight 220 g. Load figures from SKF 17000: dynamic 26.5 kN, static 50 kN, fatigue limit 1.86 kN; reference speed 3,800 r/min (thermal) and limiting speed 5,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52205 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 20 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is the double-direction 52205 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 20×47×28 mm unit locating the shaft axially in both directions."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52205",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52205"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52305",
    "brand": "SKF",
    "manufacturer_designation": "52305",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 34.5,
    "static_load_kN": 60,
    "fatigue_load_limit_kN": 2.24,
    "reference_speed_rpm": 3200,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 330,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 52300 series order number 52305 is a SKF double-direction thrust ball bearing for a 20 mm seat, built to ISO 104, with a flat housing seating surface, 20×52×34 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 20 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 20×52×34 mm (0.787×2.047×1.339 in), 16.0 mm radial section, C 34.5 kN, C0 60 kN, Pu 2.24 kN. reference speed 3,200 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 330 g. Section proportions: the 16.0 mm radial section compares with 20 mm of bore (section/bore ≈ 0.80) and the 34 mm height is 2.13× that section — the proportions that identify the 52300 envelope at a glance. Static-first selection data: 60 kN C0 spread across the 34 mm stack gives 1.8 kN of static rating per height millimetre, and the 330 g mass/C0 ratio is about 6 g per static kN — crane-hook and screw positions are normally sized on these two figures. Imperial cross-check for procurement drawings: 0.787 in bore, 2.047 in OD, 1.339 in height, and the 330 g catalogue mass converts to 0.330 kg (11.6 oz). Capacity density: 34.5 kN C from 0.330 kg of bearing steel gives about 104.5 kN per kilogram; static density is correspondingly 181.8 kN/kg at C0 60 kN. Load balance: C0 60 kN against C 34.5 kN gives a 1.74 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 2.24 kN enters the adjusted-life check. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 20 mm bore and 34 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 52 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "two-direction clamping heads",
      "reversing screw and cam spindles",
      "bidirectional thrust on small vertical shafts"
    ],
    "failure_modes": [
      "cover-induced thrust preload when the end cover is torqued solid instead of leaving the catalogue axial freedom",
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face"
    ],
    "pitfalls": [
      "Service both cage sets together: replacing only the noisy side while leaving the worn 60 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 34 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 4,500 r/min even a small thermal thrust preload smears the hottest track.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52300 unit has no alignment capacity.",
      "Ordering discipline for 52305: the catalogue page quotes 52305 and its 34.5/60 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52305?",
        "a": "Boundary dimensions to ISO 104: bore 20 mm, OD 52 mm, height 34 mm; weight 330 g. Load figures from SKF 17000: dynamic 34.5 kN, static 60 kN, fatigue limit 2.24 kN; reference speed 3,200 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52305 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 20 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is the double-direction 52305 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 20×52×34 mm unit locating the shaft axially in both directions."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52305",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52305"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52406",
    "brand": "SKF",
    "manufacturer_designation": "52406",
    "series": "52400-series",
    "type": "thrust_ball",
    "d_mm": 20,
    "D_mm": 70,
    "B_mm": 52,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 70.2,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 1000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52406 is SKF's 20 mm-bore double-direction thrust ball bearing in the 52400 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 20×70×52 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 20 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 20×70×52 mm (0.787×2.756×2.047 in), 25.0 mm radial section, C 70.2 kN, C0 122 kN, Pu 4.5 kN. reference speed 2,200 r/min (thermal) and limiting speed 3,200 r/min (mechanical), catalogue mass 1000 g. Envelope economics: the 52 mm axial height over a 25.0 mm radial section yields 1.4 kN of dynamic capacity per height millimetre, and the bearing weighs 1000 g for 70.2 kN C — about 14 g per rated kN. At the printed limiting speed of 3,200 r/min the mean pitch diameter dm ≈ 45.0 mm implies a dn value around 144k mm·r/min; the 2,200 r/min reference speed is the thermal-planning value under catalogue load. Speed band width for this size is 1,000 r/min between reference and limiting (1.45× ratio); lubrication, preload and heat removal decide where inside that band 52406 can actually run. Section proportions: the 25.0 mm radial section compares with 20 mm of bore (section/bore ≈ 1.25) and the 52 mm height is 2.08× that section — the proportions that identify the 52400 envelope at a glance. Light-load floor: Pu = 4.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52406; the number is 6 % of the 70.2 kN dynamic rating. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 20 mm bore and 52 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 70 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "office-machine reversal pivots",
      "reversing screw and cam spindles",
      "two-direction clamping heads"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Service both cage sets together: replacing only the noisy side while leaving the worn 122 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 52 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "Each direction independently needs the minimum axial load (factor A 0.097): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52400 unit has no alignment capacity.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52406 as the double flat pressed steel execution; other order numbers of the 52406 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52406?",
        "a": "52406 measures 20 mm bore × 70 mm OD × 52 mm bearing height (0.787 × 2.756 × 2.047 in), mass about 1000 g. SKF 17000 ratings: C 70.2 kN, C0 122 kN, Pu 4.5 kN, reference speed 2,200 r/min (thermal) and limiting speed 3,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52406 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 20 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "Which fits and retention does 52406 need?",
        "a": "The central shaft washer takes an interference fit on the 20 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      },
      {
        "q": "What static check governs crane-hook duty for 52406?",
        "a": "Hook and screw positions are usually sized on C0 (122 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 70.2 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52406",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52406"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52206",
    "brand": "SKF",
    "manufacturer_designation": "52206",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 25.1,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 1.86,
    "reference_speed_rpm": 3600,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52206 is SKF's 25 mm-bore double-direction thrust ball bearing in the 52200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 25×52×29 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 25 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 25×52×29 mm (0.984×2.047×1.142 in), 13.5 mm radial section, C 25.1 kN, C0 51 kN, Pu 1.86 kN. reference speed 3,600 r/min (thermal) and limiting speed 5,000 r/min (mechanical), catalogue mass 250 g. Speed band width for this size is 1,400 r/min between reference and limiting (1.39× ratio); lubrication, preload and heat removal decide where inside that band 52206 can actually run. Speed-ratio note for this exact unit: the reference speed is 3,600 r/min against a 5,000 r/min limiting speed, a reference-to-limit ratio of 0.72. Light-load floor: Pu = 1.86 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52206; the number is 7 % of the 25.1 kN dynamic rating. Pitch-diameter arithmetic: dm = (25+52)/2 = 38.5 mm; at the 5,000 r/min limiting speed that corresponds to roughly 193k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Imperial cross-check for procurement drawings: 0.984 in bore, 2.047 in OD, 1.142 in height, and the 250 g catalogue mass converts to 0.250 kg (8.8 oz). Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52206 is done separately per direction: if duty applies 25.1 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "machine-tool lead screws and selector shafts",
      "elevator machinery thrust positions",
      "steering and reversing linkages"
    ],
    "failure_modes": [
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 5,000 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 51 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Do not replace a 52206 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 25×52 mm bore and OD.",
      "The 25.1/51 kN figures belong to 52206 specifically (the double flat pressed steel execution of 52206); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52206?",
        "a": "52206 measures 25 mm bore × 52 mm OD × 29 mm bearing height (0.984 × 2.047 × 1.142 in), mass about 250 g. SKF 17000 ratings: C 25.1 kN, C0 51 kN, Pu 1.86 kN, reference speed 3,600 r/min (thermal) and limiting speed 5,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52206 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 25 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "What minimum axial load applies to a double-direction bearing?",
        "a": "The Fam ≈ A·(n·dm/1000)² rule (factor A 0.013) applies to EACH direction: the momentarily unloaded side during slow reversal is the one that skids, so preload or balanced loading must keep both ball sets seated."
      },
      {
        "q": "How is the double-direction 52206 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 25×52×29 mm unit locating the shaft axially in both directions."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52206",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52206"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52306",
    "brand": "SKF",
    "manufacturer_designation": "52306",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 60,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 35.8,
    "static_load_kN": 65.5,
    "fatigue_load_limit_kN": 2.4,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 470,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52306 is SKF's 25 mm-bore double-direction thrust ball bearing in the 52300 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 25×60×38 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 25 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 25×60×38 mm (0.984×2.362×1.496 in), 17.5 mm radial section, C 35.8 kN, C0 65.5 kN, Pu 2.4 kN. reference speed 2,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 470 g. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.026 at the 4,000 r/min limiting speed raises the required axial preload to about 751 N; the reference-speed value 368 N is the thermal design point. Imperial cross-check for procurement drawings: 0.984 in bore, 2.362 in OD, 1.496 in height, and the 470 g catalogue mass converts to 0.470 kg (16.6 oz). Rating split for documentation: dynamic 35.8 kN (L10 life), static 65.5 kN (safety factor s0), fatigue limit 2.4 kN (adjusted life) — three different uses of three different numbers for 52306, none interchangeable with another. Light-load floor: Pu = 2.4 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52306; the number is 7 % of the 35.8 kN dynamic rating. Static-first selection data: 65.5 kN C0 spread across the 38 mm stack gives 1.7 kN of static rating per height millimetre, and the 470 g mass/C0 ratio is about 7 g per static kN — crane-hook and screw positions are normally sized on these two figures. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 25 mm bore and 38 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 60 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "reversing gearbox shafts in one compact position",
      "steering and reversing linkages",
      "elevator machinery thrust positions"
    ],
    "failure_modes": [
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 4,000 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 65.5 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Do not replace a 52306 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 25×60 mm bore and OD.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52300 unit has no alignment capacity.",
      "Ordering discipline for 52306: the catalogue page quotes 52306 and its 35.8/65.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52306?",
        "a": "52306 measures 25 mm bore × 60 mm OD × 38 mm bearing height (0.984 × 2.362 × 1.496 in), mass about 470 g. SKF 17000 ratings: C 35.8 kN, C0 65.5 kN, Pu 2.4 kN, reference speed 2,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52306 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 25 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "Which fits and retention does 52306 need?",
        "a": "The central shaft washer takes an interference fit on the 25 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      },
      {
        "q": "What static check governs crane-hook duty for 52306?",
        "a": "Hook and screw positions are usually sized on C0 (65.5 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 35.8 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52306",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52306"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52407",
    "brand": "SKF",
    "manufacturer_designation": "52407",
    "series": "52400-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 80,
    "B_mm": 59,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 76.1,
    "static_load_kN": 137,
    "fatigue_load_limit_kN": 5.1,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52407 is an ISO 104 double-direction thrust ball bearing, 25 mm bore and 80 mm OD on a flat housing seat, standing 59 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52407 is 25 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 25×80×59 mm (0.984×3.15×2.323 in), 27.5 mm radial section, C 76.1 kN, C0 137 kN, Pu 5.1 kN. reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical), catalogue mass 1450 g. At the printed limiting speed of 2,800 r/min the mean pitch diameter dm ≈ 52.5 mm implies a dn value around 147k mm·r/min; the 2,000 r/min reference speed is the thermal-planning value under catalogue load. Light-load floor: Pu = 5.1 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52407; the number is 7 % of the 76.1 kN dynamic rating. Load balance: C0 137 kN against C 76.1 kN gives a 1.80 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 5.1 kN enters the adjusted-life check. Rating split for documentation: dynamic 76.1 kN (L10 life), static 137 kN (safety factor s0), fatigue limit 5.1 kN (adjusted life) — three different uses of three different numbers for 52407, none interchangeable with another. Minimum-load arithmetic: with dm ≈ 52.5 mm and factor A 0.15, Fam ≈ A·(n·dm/1000)² at the 2,000 r/min reference speed is about 1.7 kN for 52407; below that preload the balls skid and smear the tracks. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52407 is done separately per direction: if duty applies 76.1 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "elevator machinery thrust positions",
      "steering and reversing linkages",
      "reversing gearbox shafts in one compact position"
    ],
    "failure_modes": [
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Do not replace a 52407 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 25×80 mm bore and OD.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 2,800 r/min even a small thermal thrust preload smears the hottest track.",
      "The central shaft washer takes the interference fit on the 25 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Each direction independently needs the minimum axial load (factor A 0.15): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52407 as the double flat pressed steel execution; other order numbers of the 52407 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52407?",
        "a": "The catalogue envelope is 25×80×59 mm, mass 1450 g; ratings C 76.1 kN / C0 137 kN / Pu 5.1 kN, reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52407 mean?",
        "a": "note the bore of 52407 is 25 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is a vertical double-direction 52407 lubricated and retained?",
        "a": "Use an oil bath reaching the lower track plus a feed or oil level that serves the upper cage set, or a coherent heavy-base grease; positively retain both loose housing washers because gravity loads the upper stack differently at standstill."
      },
      {
        "q": "Which fits and retention does 52407 need?",
        "a": "The central shaft washer takes an interference fit on the 25 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52407",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52407"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52207",
    "brand": "SKF",
    "manufacturer_designation": "52207",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 35.1,
    "static_load_kN": 73.5,
    "fatigue_load_limit_kN": 2.7,
    "reference_speed_rpm": 3000,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 410,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 52200 series order number 52207 is a SKF double-direction thrust ball bearing for a 30 mm seat, built to ISO 104, with a flat housing seating surface, 30×62×34 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 30 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 30×62×34 mm (1.181×2.441×1.339 in), 16.0 mm radial section, C 35.1 kN, C0 73.5 kN, Pu 2.7 kN. reference speed 3,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 410 g. Pitch-diameter arithmetic: dm = (30+62)/2 = 46.0 mm; at the 4,300 r/min limiting speed that corresponds to roughly 198k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Minimum-load arithmetic: with dm ≈ 46.0 mm and factor A 0.028, Fam ≈ A·(n·dm/1000)² at the 3,000 r/min reference speed is about 533 N for 52207; below that preload the balls skid and smear the tracks. Track-circle loading: per millimetre of mean track circumference the 35.1 kN dynamic rating corresponds to roughly 0.24 kN/mm of π·dm track, a useful comparison against the other dimension series of the 30 mm bore. Rating split for documentation: dynamic 35.1 kN (L10 life), static 73.5 kN (safety factor s0), fatigue limit 2.7 kN (adjusted life) — three different uses of three different numbers for 52207, none interchangeable with another. Stack/annulus proportions: the 34 mm axial stack over the 2,312 mm² washer annulus gives 14.71 mm of height per annular square millimetre ×10⁻³, and at 410 g the bearing holds about 179.3 kN of C0 per kilogram. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 30 mm bore and 34 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 62 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "vertical pumps with intermittent up-thrust",
      "elevator machinery thrust positions",
      "steering and reversing linkages"
    ],
    "failure_modes": [
      "assembly damage when the central shaft washer is fitted reversed or the two outward-facing housing washers are swapped",
      "cover-induced thrust preload when the end cover is torqued solid instead of leaving the catalogue axial freedom",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 4,300 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 73.5 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Do not replace a 52207 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 30×62 mm bore and OD.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Ordering discipline for 52207: the catalogue page quotes 52207 and its 35.1/73.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52207?",
        "a": "Boundary dimensions to ISO 104: bore 30 mm, OD 62 mm, height 34 mm; weight 410 g. Load figures from SKF 17000: dynamic 35.1 kN, static 73.5 kN, fatigue limit 2.7 kN; reference speed 3,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52207 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 30 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      },
      {
        "q": "Can it replace two single-direction 51-series bearings?",
        "a": "It replaces a mirrored pair functionally — one fit, one housing bore, factory-matched geometry — but its 34 mm height is not twice the single-bearing height and seat details differ, so the housing and cover must be re-drawn rather than swapped in place."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52207",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52207"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52208",
    "brand": "SKF",
    "manufacturer_designation": "52208",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 68,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 44.2,
    "static_load_kN": 96.5,
    "fatigue_load_limit_kN": 3.6,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52208 is SKF's 30 mm-bore double-direction thrust ball bearing in the 52200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 30×68×36 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 30 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 30×68×36 mm (1.181×2.677×1.417 in), 19.0 mm radial section, C 44.2 kN, C0 96.5 kN, Pu 3.6 kN. reference speed 2,800 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 550 g. Load balance: C0 96.5 kN against C 44.2 kN gives a 2.18 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 3.6 kN enters the adjusted-life check. Selection figures for 52208: the C0/C ratio is 2.18, Pu 3.6 kN is about 8 % of C, and the catalogue mass works out to roughly 18 g per millimetre of bore; the printed minimum-load factor is A 0.058. Minimum-load arithmetic: with dm ≈ 49.0 mm and factor A 0.058, Fam ≈ A·(n·dm/1000)² at the 2,800 r/min reference speed is about 1.1 kN for 52208; below that preload the balls skid and smear the tracks. Mass and section check: 550 g inside the 30×68×36 mm outline leaves a 19.0 mm radial section, and the 96.5 kN static rating is 2.18× the dynamic rating — plan static safety and minimum preload against those figures. Bore-to-OD planning: OD 68 over bore 30 is a 2.27× step for this size, and the 36 mm height gives a bore/height ratio of 0.83; use these ratios when the housing recess around the 30 mm shaft is the first constraint. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52208 is done separately per direction: if duty applies 44.2 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "machine-tool lead screws and selector shafts",
      "vertical pumps with intermittent up-thrust",
      "elevator machinery thrust positions"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face"
    ],
    "pitfalls": [
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Do not replace a 52208 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 30×68 mm bore and OD.",
      "Each direction independently needs the minimum axial load (factor A 0.058): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "The double-direction 52208 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 30 mm shaft axially in both directions instead of a mirrored pair.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52208 as the double flat pressed steel execution; other order numbers of the 52208 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52208?",
        "a": "52208 measures 30 mm bore × 68 mm OD × 36 mm bearing height (1.181 × 2.677 × 1.417 in), mass about 550 g. SKF 17000 ratings: C 44.2 kN, C0 96.5 kN, Pu 3.6 kN, reference speed 2,800 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52208 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 30 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "What static check governs crane-hook duty for 52208?",
        "a": "Hook and screw positions are usually sized on C0 (96.5 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 44.2 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      },
      {
        "q": "What minimum axial load applies to a double-direction bearing?",
        "a": "The Fam ≈ A·(n·dm/1000)² rule (factor A 0.058) applies to EACH direction: the momentarily unloaded side during slow reversal is the one that skids, so preload or balanced loading must keep both ball sets seated."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52208",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52208"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52307",
    "brand": "SKF",
    "manufacturer_designation": "52307",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 68,
    "B_mm": 44,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 49.4,
    "static_load_kN": 96.5,
    "fatigue_load_limit_kN": 3.55,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 680,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52307 is an ISO 104 double-direction thrust ball bearing, 30 mm bore and 68 mm OD on a flat housing seat, standing 44 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52307 is 30 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 30×68×44 mm (1.181×2.677×1.732 in), 19.0 mm radial section, C 49.4 kN, C0 96.5 kN, Pu 3.55 kN. reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 680 g. Selection figures for 52307: the C0/C ratio is 1.95, Pu 3.55 kN is about 7 % of C, and the catalogue mass works out to roughly 23 g per millimetre of bore; the printed minimum-load factor is A 0.048. Bore-to-OD planning: OD 68 over bore 30 is a 2.27× step for this size, and the 44 mm height gives a bore/height ratio of 0.68; use these ratios when the housing recess around the 30 mm shaft is the first constraint. At the printed limiting speed of 3,400 r/min the mean pitch diameter dm ≈ 49.0 mm implies a dn value around 167k mm·r/min; the 2,400 r/min reference speed is the thermal-planning value under catalogue load. Light-load floor: Pu = 3.55 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52307; the number is 7 % of the 49.4 kN dynamic rating. Track-circle loading: per millimetre of mean track circumference the 49.4 kN dynamic rating corresponds to roughly 0.32 kN/mm of π·dm track, a useful comparison against the other dimension series of the 30 mm bore. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 30 mm bore and 44 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 68 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "steering and reversing linkages",
      "vertical pumps with intermittent up-thrust",
      "machine-tool lead screws and selector shafts"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Do not replace a 52307 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 30×68 mm bore and OD.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 3,400 r/min even a small thermal thrust preload smears the hottest track.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52300 unit has no alignment capacity.",
      "The central shaft washer takes the interference fit on the 30 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52307 as the double flat pressed steel execution; other order numbers of the 52307 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52307?",
        "a": "The catalogue envelope is 30×68×44 mm, mass 680 g; ratings C 49.4 kN / C0 96.5 kN / Pu 3.55 kN, reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52307 mean?",
        "a": "note the bore of 52307 is 30 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "Which fits and retention does 52307 need?",
        "a": "The central shaft washer takes an interference fit on the 30 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      },
      {
        "q": "What static check governs crane-hook duty for 52307?",
        "a": "Hook and screw positions are usually sized on C0 (96.5 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 49.4 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52307",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52307"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52308",
    "brand": "SKF",
    "manufacturer_designation": "52308",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 78,
    "B_mm": 49,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 61.8,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 1050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 52300 series order number 52308 is a SKF double-direction thrust ball bearing for a 30 mm seat, built to ISO 104, with a flat housing seating surface, 30×78×49 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 30 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 30×78×49 mm (1.181×3.071×1.929 in), 24.0 mm radial section, C 61.8 kN, C0 122 kN, Pu 4.5 kN. reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 1050 g. Envelope economics: the 49 mm axial height over a 24.0 mm radial section yields 1.3 kN of dynamic capacity per height millimetre, and the bearing weighs 1050 g for 61.8 kN C — about 17 g per rated kN. Mass and section check: 1050 g inside the 30×78×49 mm outline leaves a 24.0 mm radial section, and the 122 kN static rating is 1.97× the dynamic rating — plan static safety and minimum preload against those figures. Rating split for documentation: dynamic 61.8 kN (L10 life), static 122 kN (safety factor s0), fatigue limit 4.5 kN (adjusted life) — three different uses of three different numbers for 52308, none interchangeable with another. Light-load floor: Pu = 4.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52308; the number is 7 % of the 61.8 kN dynamic rating. Static-first selection data: 122 kN C0 spread across the 49 mm stack gives 2.5 kN of static rating per height millimetre, and the 1050 g mass/C0 ratio is about 9 g per static kN — crane-hook and screw positions are normally sized on these two figures. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52308 is done separately per direction: if duty applies 61.8 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "vertical pumps with intermittent up-thrust",
      "steering and reversing linkages",
      "elevator machinery thrust positions"
    ],
    "failure_modes": [
      "cover-induced thrust preload when the end cover is torqued solid instead of leaving the catalogue axial freedom",
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The double-direction 52308 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 30 mm shaft axially in both directions instead of a mirrored pair.",
      "Each direction independently needs the minimum axial load (factor A 0.077): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "Do not replace a 52308 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 30×78 mm bore and OD.",
      "The central shaft washer takes the interference fit on the 30 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Ordering discipline for 52308: the catalogue page quotes 52308 and its 61.8/122 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52308?",
        "a": "Boundary dimensions to ISO 104: bore 30 mm, OD 78 mm, height 49 mm; weight 1050 g. Load figures from SKF 17000: dynamic 61.8 kN, static 122 kN, fatigue limit 4.5 kN; reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52308 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 30 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "Which fits and retention does 52308 need?",
        "a": "The central shaft washer takes an interference fit on the 30 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      },
      {
        "q": "What static check governs crane-hook duty for 52308?",
        "a": "Hook and screw positions are usually sized on C0 (122 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 61.8 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52308",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52308"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52408",
    "brand": "SKF",
    "manufacturer_designation": "52408",
    "series": "52400-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 90,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 95.6,
    "static_load_kN": 183,
    "fatigue_load_limit_kN": 6.8,
    "reference_speed_rpm": 1800,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 2050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52408 is an ISO 104 double-direction thrust ball bearing, 30 mm bore and 90 mm OD on a flat housing seat, standing 65 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52408 is 30 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 30×90×65 mm (1.181×3.543×2.559 in), 30.0 mm radial section, C 95.6 kN, C0 183 kN, Pu 6.8 kN. reference speed 1,800 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 2050 g. Pitch-diameter arithmetic: dm = (30+90)/2 = 60.0 mm; at the 2,400 r/min limiting speed that corresponds to roughly 144k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Track-circle loading: per millimetre of mean track circumference the 95.6 kN dynamic rating corresponds to roughly 0.51 kN/mm of π·dm track, a useful comparison against the other dimension series of the 30 mm bore. Rating split for documentation: dynamic 95.6 kN (L10 life), static 183 kN (safety factor s0), fatigue limit 6.8 kN (adjusted life) — three different uses of three different numbers for 52408, none interchangeable with another. Sizing arithmetic on the 30 mm bore: 95.6 kN C over the 30.0 mm radial section gives 3.2 kN per section millimetre, and the 65 mm stack height is 2.17× that section — proportions typical of a 52400 thrust section. Static-first selection data: 183 kN C0 spread across the 65 mm stack gives 2.8 kN of static rating per height millimetre, and the 2050 g mass/C0 ratio is about 11 g per static kN — crane-hook and screw positions are normally sized on these two figures. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52408 is done separately per direction: if duty applies 95.6 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "reversing gearbox shafts in one compact position",
      "machine-tool lead screws and selector shafts",
      "vertical pumps with intermittent up-thrust"
    ],
    "failure_modes": [
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52400 unit has no alignment capacity.",
      "Do not replace a 52408 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 30×90 mm bore and OD.",
      "The double-direction 52408 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 30 mm shaft axially in both directions instead of a mirrored pair.",
      "Each direction independently needs the minimum axial load (factor A 0.26): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "The 95.6/183 kN figures belong to 52408 specifically (the double flat pressed steel execution of 52408); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52408?",
        "a": "The catalogue envelope is 30×90×65 mm, mass 2050 g; ratings C 95.6 kN / C0 183 kN / Pu 6.8 kN, reference speed 1,800 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52408 mean?",
        "a": "note the bore of 52408 is 30 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      },
      {
        "q": "Can it replace two single-direction 51-series bearings?",
        "a": "It replaces a mirrored pair functionally — one fit, one housing bore, factory-matched geometry — but its 65 mm height is not twice the single-bearing height and seat details differ, so the housing and cover must be re-drawn rather than swapped in place."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52408",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52408"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52209",
    "brand": "SKF",
    "manufacturer_designation": "52209",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 73,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 39,
    "static_load_kN": 86.5,
    "fatigue_load_limit_kN": 3.2,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52209 is SKF's 35 mm-bore double-direction thrust ball bearing in the 52200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 35×73×37 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 35 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 35×73×37 mm (1.378×2.874×1.457 in), 19.0 mm radial section, C 39 kN, C0 86.5 kN, Pu 3.2 kN. reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 600 g. Envelope economics: the 37 mm axial height over a 19.0 mm radial section yields 1.1 kN of dynamic capacity per height millimetre, and the bearing weighs 600 g for 39 kN C — about 15 g per rated kN. Light-load floor: Pu = 3.2 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52209; the number is 8 % of the 39 kN dynamic rating. Rating split for documentation: dynamic 39 kN (L10 life), static 86.5 kN (safety factor s0), fatigue limit 3.2 kN (adjusted life) — three different uses of three different numbers for 52209, none interchangeable with another. Selection figures for 52209: the C0/C ratio is 2.22, Pu 3.2 kN is about 8 % of C, and the catalogue mass works out to roughly 17 g per millimetre of bore; the printed minimum-load factor is A 0.038. Mass and section check: 600 g inside the 35×73×37 mm outline leaves a 19.0 mm radial section, and the 86.5 kN static rating is 2.22× the dynamic rating — plan static safety and minimum preload against those figures. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52209 is done separately per direction: if duty applies 39 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "elevator machinery thrust positions",
      "machine-tool lead screws and selector shafts",
      "vertical pumps with intermittent up-thrust"
    ],
    "failure_modes": [
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "track rust staining from condensate during long idle periods in humid plant air",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The double-direction 52209 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 35 mm shaft axially in both directions instead of a mirrored pair.",
      "Each direction independently needs the minimum axial load (factor A 0.038): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "Do not replace a 52209 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 35×73 mm bore and OD.",
      "The central shaft washer takes the interference fit on the 35 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "The 39/86.5 kN figures belong to 52209 specifically (the double flat pressed steel execution of 52209); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52209?",
        "a": "52209 measures 35 mm bore × 73 mm OD × 37 mm bearing height (1.378 × 2.874 × 1.457 in), mass about 600 g. SKF 17000 ratings: C 39 kN, C0 86.5 kN, Pu 3.2 kN, reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52209 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 35 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is a vertical double-direction 52209 lubricated and retained?",
        "a": "Use an oil bath reaching the lower track plus a feed or oil level that serves the upper cage set, or a coherent heavy-base grease; positively retain both loose housing washers because gravity loads the upper stack differently at standstill."
      },
      {
        "q": "Which fits and retention does 52209 need?",
        "a": "The central shaft washer takes an interference fit on the 35 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52209",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52209"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52309",
    "brand": "SKF",
    "manufacturer_designation": "52309",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 85,
    "B_mm": 52,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 76.1,
    "static_load_kN": 153,
    "fatigue_load_limit_kN": 5.6,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 1250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52309 is an ISO 104 double-direction thrust ball bearing, 35 mm bore and 85 mm OD on a flat housing seat, standing 52 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52309 is 35 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 35×85×52 mm (1.378×3.346×2.047 in), 25.0 mm radial section, C 76.1 kN, C0 153 kN, Pu 5.6 kN. reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical), catalogue mass 1250 g. Selection figures for 52309: the C0/C ratio is 2.01, Pu 5.6 kN is about 7 % of C, and the catalogue mass works out to roughly 36 g per millimetre of bore; the printed minimum-load factor is A 0.12. Section proportions: the 25.0 mm radial section compares with 35 mm of bore (section/bore ≈ 0.71) and the 52 mm height is 2.08× that section — the proportions that identify the 52300 envelope at a glance. Static-first selection data: 153 kN C0 spread across the 52 mm stack gives 2.9 kN of static rating per height millimetre, and the 1250 g mass/C0 ratio is about 8 g per static kN — crane-hook and screw positions are normally sized on these two figures. Minimum-load arithmetic: with dm ≈ 60.0 mm and factor A 0.12, Fam ≈ A·(n·dm/1000)² at the 2,000 r/min reference speed is about 1.7 kN for 52309; below that preload the balls skid and smear the tracks. Bore-to-OD planning: OD 85 over bore 35 is a 2.43× step for this size, and the 52 mm height gives a bore/height ratio of 0.67; use these ratios when the housing recess around the 35 mm shaft is the first constraint. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 35 mm bore and 52 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 85 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "elevator machinery thrust positions",
      "reversing gearbox shafts in one compact position",
      "vertical pumps with intermittent up-thrust"
    ],
    "failure_modes": [
      "cover-induced thrust preload when the end cover is torqued solid instead of leaving the catalogue axial freedom",
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The central shaft washer takes the interference fit on the 35 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52300 unit has no alignment capacity.",
      "Each direction independently needs the minimum axial load (factor A 0.12): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 153 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Ordering discipline for 52309: the catalogue page quotes 52309 and its 76.1/153 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52309?",
        "a": "The catalogue envelope is 35×85×52 mm, mass 1250 g; ratings C 76.1 kN / C0 153 kN / Pu 5.6 kN, reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52309 mean?",
        "a": "note the bore of 52309 is 35 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is a vertical double-direction 52309 lubricated and retained?",
        "a": "Use an oil bath reaching the lower track plus a feed or oil level that serves the upper cage set, or a coherent heavy-base grease; positively retain both loose housing washers because gravity loads the upper stack differently at standstill."
      },
      {
        "q": "Which fits and retention does 52309 need?",
        "a": "The central shaft washer takes an interference fit on the 35 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52309",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52309"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52409",
    "brand": "SKF",
    "manufacturer_designation": "52409",
    "series": "52400-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 100,
    "B_mm": 72,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 124,
    "static_load_kN": 240,
    "fatigue_load_limit_kN": 9,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 2700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52409 is SKF's 35 mm-bore double-direction thrust ball bearing in the 52400 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 35×100×72 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 35 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 35×100×72 mm (1.378×3.937×2.835 in), 32.5 mm radial section, C 124 kN, C0 240 kN, Pu 9 kN. reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 2700 g. Track-circle loading: per millimetre of mean track circumference the 124 kN dynamic rating corresponds to roughly 0.58 kN/mm of π·dm track, a useful comparison against the other dimension series of the 35 mm bore. Speed band width for this size is 600 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 52409 can actually run. Light-load floor: Pu = 9 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52409; the number is 7 % of the 124 kN dynamic rating. Sizing arithmetic on the 35 mm bore: 124 kN C over the 32.5 mm radial section gives 3.8 kN per section millimetre, and the 72 mm stack height is 2.22× that section — proportions typical of a 52400 thrust section. Mass and section check: 2700 g inside the 35×100×72 mm outline leaves a 32.5 mm radial section, and the 240 kN static rating is 1.94× the dynamic rating — plan static safety and minimum preload against those figures. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52409 is done separately per direction: if duty applies 124 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "machine-tool lead screws and selector shafts",
      "steering and reversing linkages",
      "elevator machinery thrust positions"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Do not replace a 52409 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 35×100 mm bore and OD.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 2,200 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 240 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "The central shaft washer takes the interference fit on the 35 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52409 as the double flat pressed steel execution; other order numbers of the 52409 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52409?",
        "a": "52409 measures 35 mm bore × 100 mm OD × 72 mm bearing height (1.378 × 3.937 × 2.835 in), mass about 2700 g. SKF 17000 ratings: C 124 kN, C0 240 kN, Pu 9 kN, reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52409 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 35 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "What static check governs crane-hook duty for 52409?",
        "a": "Hook and screw positions are usually sized on C0 (240 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 124 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      },
      {
        "q": "What minimum axial load applies to a double-direction bearing?",
        "a": "The Fam ≈ A·(n·dm/1000)² rule (factor A 0.37) applies to EACH direction: the momentarily unloaded side during slow reversal is the one that skids, so preload or balanced loading must keep both ball sets seated."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52409",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52409"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52210",
    "brand": "SKF",
    "manufacturer_designation": "52210",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 78,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 49.4,
    "static_load_kN": 116,
    "fatigue_load_limit_kN": 4.3,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 710,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52210 is SKF's 40 mm-bore double-direction thrust ball bearing in the 52200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 40×78×39 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 40 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 40×78×39 mm (1.575×3.071×1.535 in), 19.0 mm radial section, C 49.4 kN, C0 116 kN, Pu 4.3 kN. reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 710 g. Light-load floor: Pu = 4.3 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52210; the number is 9 % of the 49.4 kN dynamic rating. Mass and section check: 710 g inside the 40×78×39 mm outline leaves a 19.0 mm radial section, and the 116 kN static rating is 2.35× the dynamic rating — plan static safety and minimum preload against those figures. At the printed limiting speed of 3,400 r/min the mean pitch diameter dm ≈ 59.0 mm implies a dn value around 201k mm·r/min; the 2,400 r/min reference speed is the thermal-planning value under catalogue load. Rating split for documentation: dynamic 49.4 kN (L10 life), static 116 kN (safety factor s0), fatigue limit 4.3 kN (adjusted life) — three different uses of three different numbers for 52210, none interchangeable with another. Capacity density: 49.4 kN C from 0.710 kg of bearing steel gives about 69.6 kN per kilogram; static density is correspondingly 163.4 kN/kg at C0 116 kN. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 40 mm bore and 39 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 78 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "reversing gearbox shafts in one compact position",
      "elevator machinery thrust positions",
      "machine-tool lead screws and selector shafts"
    ],
    "failure_modes": [
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Each direction independently needs the minimum axial load (factor A 0.069): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "The central shaft washer takes the interference fit on the 40 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Do not replace a 52210 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 40×78 mm bore and OD.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 39 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "Ordering discipline for 52210: the catalogue page quotes 52210 and its 49.4/116 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52210?",
        "a": "52210 measures 40 mm bore × 78 mm OD × 39 mm bearing height (1.575 × 3.071 × 1.535 in), mass about 710 g. SKF 17000 ratings: C 49.4 kN, C0 116 kN, Pu 4.3 kN, reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52210 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 40 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "Which fits and retention does 52210 need?",
        "a": "The central shaft washer takes an interference fit on the 40 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      },
      {
        "q": "What static check governs crane-hook duty for 52210?",
        "a": "Hook and screw positions are usually sized on C0 (116 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 49.4 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52210",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52210"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52310",
    "brand": "SKF",
    "manufacturer_designation": "52310",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 95,
    "B_mm": 58,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 81.9,
    "static_load_kN": 170,
    "fatigue_load_limit_kN": 6.3,
    "reference_speed_rpm": 1800,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52310 is an ISO 104 double-direction thrust ball bearing, 40 mm bore and 95 mm OD on a flat housing seat, standing 58 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52310 is 40 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 40×95×58 mm (1.575×3.74×2.283 in), 27.5 mm radial section, C 81.9 kN, C0 170 kN, Pu 6.3 kN. reference speed 1,800 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 1750 g. Capacity density: 81.9 kN C from 1.750 kg of bearing steel gives about 46.8 kN per kilogram; static density is correspondingly 97.1 kN/kg at C0 170 kN. Speed-ratio note for this exact unit: the reference speed is 1,800 r/min against a 2,600 r/min limiting speed, a reference-to-limit ratio of 0.69. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.19 at the 2,600 r/min limiting speed raises the required axial preload to about 5.9 kN; the reference-speed value 2.8 kN is the thermal design point. Minimum-load arithmetic: with dm ≈ 67.5 mm and factor A 0.19, Fam ≈ A·(n·dm/1000)² at the 1,800 r/min reference speed is about 2.8 kN for 52310; below that preload the balls skid and smear the tracks. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 2,600 r/min while thermal balance under catalogue load sets the 1,800 r/min reference; at dm ≈ 67.5 mm the corresponding dn is approximately 176k mm·r/min. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52310 is done separately per direction: if duty applies 81.9 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "steering and reversing linkages",
      "elevator machinery thrust positions",
      "reversing gearbox shafts in one compact position"
    ],
    "failure_modes": [
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 58 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "The double-direction 52310 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 40 mm shaft axially in both directions instead of a mirrored pair.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52300 unit has no alignment capacity.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 2,600 r/min even a small thermal thrust preload smears the hottest track.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52310 as the double flat pressed steel execution; other order numbers of the 52310 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52310?",
        "a": "The catalogue envelope is 40×95×58 mm, mass 1750 g; ratings C 81.9 kN / C0 170 kN / Pu 6.3 kN, reference speed 1,800 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52310 mean?",
        "a": "note the bore of 52310 is 40 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      },
      {
        "q": "Can it replace two single-direction 51-series bearings?",
        "a": "It replaces a mirrored pair functionally — one fit, one housing bore, factory-matched geometry — but its 58 mm height is not twice the single-bearing height and seat details differ, so the housing and cover must be re-drawn rather than swapped in place."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52310",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52310"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52211",
    "brand": "SKF",
    "manufacturer_designation": "52211",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 90,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 58.5,
    "static_load_kN": 134,
    "fatigue_load_limit_kN": 4.9,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52211 is an ISO 104 double-direction thrust ball bearing, 45 mm bore and 90 mm OD on a flat housing seat, standing 45 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52211 is 45 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 45×90×45 mm (1.772×3.543×1.772 in), 22.5 mm radial section, C 58.5 kN, C0 134 kN, Pu 4.9 kN. reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 1100 g. Sizing arithmetic on the 45 mm bore: 58.5 kN C over the 22.5 mm radial section gives 2.6 kN per section millimetre, and the 45 mm stack height is 2.00× that section — proportions typical of a 52200 thrust section. Imperial cross-check for procurement drawings: 1.772 in bore, 3.543 in OD, 1.772 in height, and the 1100 g catalogue mass converts to 1.100 kg (38.8 oz). Light-load floor: Pu = 4.9 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52211; the number is 8 % of the 58.5 kN dynamic rating. Minimum-load arithmetic: with dm ≈ 67.5 mm and factor A 0.11, Fam ≈ A·(n·dm/1000)² at the 2,200 r/min reference speed is about 2.4 kN for 52211; below that preload the balls skid and smear the tracks. Speed-ratio note for this exact unit: the reference speed is 2,200 r/min against a 3,000 r/min limiting speed, a reference-to-limit ratio of 0.73. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52211 is done separately per direction: if duty applies 58.5 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "vertical pumps with intermittent up-thrust",
      "elevator machinery thrust positions",
      "reversing gearbox shafts in one compact position"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume"
    ],
    "pitfalls": [
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Do not replace a 52211 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 45×90 mm bore and OD.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 45 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "The double-direction 52211 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 45 mm shaft axially in both directions instead of a mirrored pair.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52211 as the double flat pressed steel execution; other order numbers of the 52211 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52211?",
        "a": "The catalogue envelope is 45×90×45 mm, mass 1100 g; ratings C 58.5 kN / C0 134 kN / Pu 4.9 kN, reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52211 mean?",
        "a": "note the bore of 52211 is 45 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "What minimum axial load applies to a double-direction bearing?",
        "a": "The Fam ≈ A·(n·dm/1000)² rule (factor A 0.11) applies to EACH direction: the momentarily unloaded side during slow reversal is the one that skids, so preload or balanced loading must keep both ball sets seated."
      },
      {
        "q": "How is the double-direction 52211 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 45×90×45 mm unit locating the shaft axially in both directions."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52211",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52211"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52311",
    "brand": "SKF",
    "manufacturer_designation": "52311",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 105,
    "B_mm": 64,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 101,
    "static_load_kN": 224,
    "fatigue_load_limit_kN": 8.3,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 2400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 52300 series order number 52311 is a SKF double-direction thrust ball bearing for a 45 mm seat, built to ISO 104, with a flat housing seating surface, 45×105×64 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 45 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 45×105×64 mm (1.772×4.134×2.52 in), 30.0 mm radial section, C 101 kN, C0 224 kN, Pu 8.3 kN. reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 2400 g. Mass and section check: 2400 g inside the 45×105×64 mm outline leaves a 30.0 mm radial section, and the 224 kN static rating is 2.22× the dynamic rating — plan static safety and minimum preload against those figures. Light-load floor: Pu = 8.3 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52311; the number is 8 % of the 101 kN dynamic rating. Track-circle loading: per millimetre of mean track circumference the 101 kN dynamic rating corresponds to roughly 0.43 kN/mm of π·dm track, a useful comparison against the other dimension series of the 45 mm bore. Load balance: C0 224 kN against C 101 kN gives a 2.22 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 8.3 kN enters the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 1,600 r/min against a 2,200 r/min limiting speed, a reference-to-limit ratio of 0.73. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 45 mm bore and 64 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 105 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "elevator machinery thrust positions",
      "vertical pumps with intermittent up-thrust",
      "steering and reversing linkages"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "cover-induced thrust preload when the end cover is torqued solid instead of leaving the catalogue axial freedom",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 2,200 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 224 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Do not replace a 52311 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 45×105 mm bore and OD.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52300 unit has no alignment capacity.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52311 as the double flat pressed steel execution; other order numbers of the 52311 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52311?",
        "a": "Boundary dimensions to ISO 104: bore 45 mm, OD 105 mm, height 64 mm; weight 2400 g. Load figures from SKF 17000: dynamic 101 kN, static 224 kN, fatigue limit 8.3 kN; reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52311 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 45 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is a vertical double-direction 52311 lubricated and retained?",
        "a": "Use an oil bath reaching the lower track plus a feed or oil level that serves the upper cage set, or a coherent heavy-base grease; positively retain both loose housing washers because gravity loads the upper stack differently at standstill."
      },
      {
        "q": "Which fits and retention does 52311 need?",
        "a": "The central shaft washer takes an interference fit on the 45 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52311",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52311"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52411",
    "brand": "SKF",
    "manufacturer_designation": "52411",
    "series": "52400-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 120,
    "B_mm": 87,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 195,
    "static_load_kN": 400,
    "fatigue_load_limit_kN": 14.6,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "weight_g": 4700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52411 is an ISO 104 double-direction thrust ball bearing, 45 mm bore and 120 mm OD on a flat housing seat, standing 87 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52411 is 45 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 45×120×87 mm (1.772×4.724×3.425 in), 37.5 mm radial section, C 195 kN, C0 400 kN, Pu 14.6 kN. reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical), catalogue mass 4700 g. Speed-ratio note for this exact unit: the reference speed is 1,300 r/min against a 1,800 r/min limiting speed, a reference-to-limit ratio of 0.72. Bore-to-OD planning: OD 120 over bore 45 is a 2.67× step for this size, and the 87 mm height gives a bore/height ratio of 0.52; use these ratios when the housing recess around the 45 mm shaft is the first constraint. Stack/annulus proportions: the 87 mm axial stack over the 9,719 mm² washer annulus gives 8.95 mm of height per annular square millimetre ×10⁻³, and at 4700 g the bearing holds about 85.1 kN of C0 per kilogram. Section proportions: the 37.5 mm radial section compares with 45 mm of bore (section/bore ≈ 0.83) and the 87 mm height is 2.32× that section — the proportions that identify the 52400 envelope at a glance. Speed band width for this size is 500 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 52411 can actually run. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 45 mm bore and 87 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 120 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "machine-tool lead screws and selector shafts",
      "vertical pumps with intermittent up-thrust",
      "elevator machinery thrust positions"
    ],
    "failure_modes": [
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "The central shaft washer takes the interference fit on the 45 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52400 unit has no alignment capacity.",
      "Each direction independently needs the minimum axial load (factor A 0.79): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 400 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "The 195/400 kN figures belong to 52411 specifically (the double flat pressed steel execution of 52411); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52411?",
        "a": "The catalogue envelope is 45×120×87 mm, mass 4700 g; ratings C 195 kN / C0 400 kN / Pu 14.6 kN, reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52411 mean?",
        "a": "note the bore of 52411 is 45 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      },
      {
        "q": "Can it replace two single-direction 51-series bearings?",
        "a": "It replaces a mirrored pair functionally — one fit, one housing bore, factory-matched geometry — but its 87 mm height is not twice the single-bearing height and seat details differ, so the housing and cover must be re-drawn rather than swapped in place."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52411",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52411"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52212",
    "brand": "SKF",
    "manufacturer_designation": "52212",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 95,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 59.2,
    "static_load_kN": 140,
    "fatigue_load_limit_kN": 5.1,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 52200 series order number 52212 is a SKF double-direction thrust ball bearing for a 50 mm seat, built to ISO 104, with a flat housing seating surface, 50×95×46 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 50 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 50×95×46 mm (1.969×3.74×1.811 in), 22.5 mm radial section, C 59.2 kN, C0 140 kN, Pu 5.1 kN. reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical), catalogue mass 1200 g. Minimum-load arithmetic: with dm ≈ 72.5 mm and factor A 0.12, Fam ≈ A·(n·dm/1000)² at the 2,000 r/min reference speed is about 2.5 kN for 52212; below that preload the balls skid and smear the tracks. Load balance: C0 140 kN against C 59.2 kN gives a 2.36 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 5.1 kN enters the adjusted-life check. Bore-to-OD planning: OD 95 over bore 50 is a 1.90× step for this size, and the 46 mm height gives a bore/height ratio of 1.09; use these ratios when the housing recess around the 50 mm shaft is the first constraint. Light-load floor: Pu = 5.1 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52212; the number is 9 % of the 59.2 kN dynamic rating. Static-first selection data: 140 kN C0 spread across the 46 mm stack gives 3.0 kN of static rating per height millimetre, and the 1200 g mass/C0 ratio is about 9 g per static kN — crane-hook and screw positions are normally sized on these two figures. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 50 mm bore and 46 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 95 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "steering and reversing linkages",
      "elevator machinery thrust positions",
      "reversing gearbox shafts in one compact position"
    ],
    "failure_modes": [
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "assembly damage when the central shaft washer is fitted reversed or the two outward-facing housing washers are swapped",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 2,800 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 140 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Do not replace a 52212 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 50×95 mm bore and OD.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Ordering discipline for 52212: the catalogue page quotes 52212 and its 59.2/140 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52212?",
        "a": "Boundary dimensions to ISO 104: bore 50 mm, OD 95 mm, height 46 mm; weight 1200 g. Load figures from SKF 17000: dynamic 59.2 kN, static 140 kN, fatigue limit 5.1 kN; reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52212 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 50 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "What minimum axial load applies to a double-direction bearing?",
        "a": "The Fam ≈ A·(n·dm/1000)² rule (factor A 0.12) applies to EACH direction: the momentarily unloaded side during slow reversal is the one that skids, so preload or balanced loading must keep both ball sets seated."
      },
      {
        "q": "How is the double-direction 52212 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 50×95×46 mm unit locating the shaft axially in both directions."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52212",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52212"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52312",
    "brand": "SKF",
    "manufacturer_designation": "52312",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 64,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 101,
    "static_load_kN": 224,
    "fatigue_load_limit_kN": 8.3,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 2550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52312 is SKF's 50 mm-bore double-direction thrust ball bearing in the 52300 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 50×110×64 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 50 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 50×110×64 mm (1.969×4.331×2.52 in), 30.0 mm radial section, C 101 kN, C0 224 kN, Pu 8.3 kN. reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 2550 g. Mass and section check: 2550 g inside the 50×110×64 mm outline leaves a 30.0 mm radial section, and the 224 kN static rating is 2.22× the dynamic rating — plan static safety and minimum preload against those figures. Envelope economics: the 64 mm axial height over a 30.0 mm radial section yields 1.6 kN of dynamic capacity per height millimetre, and the bearing weighs 2550 g for 101 kN C — about 25 g per rated kN. Load balance: C0 224 kN against C 101 kN gives a 2.22 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 8.3 kN enters the adjusted-life check. Light-load floor: Pu = 8.3 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52312; the number is 8 % of the 101 kN dynamic rating. Bore-to-OD planning: OD 110 over bore 50 is a 2.20× step for this size, and the 64 mm height gives a bore/height ratio of 0.78; use these ratios when the housing recess around the 50 mm shaft is the first constraint. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52312 is done separately per direction: if duty applies 101 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "machine-tool lead screws and selector shafts",
      "reversing gearbox shafts in one compact position",
      "vertical pumps with intermittent up-thrust"
    ],
    "failure_modes": [
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 2,200 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 224 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Do not replace a 52312 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 50×110 mm bore and OD.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52300 unit has no alignment capacity.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52312 as the double flat pressed steel execution; other order numbers of the 52312 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52312?",
        "a": "52312 measures 50 mm bore × 110 mm OD × 64 mm bearing height (1.969 × 4.331 × 2.52 in), mass about 2550 g. SKF 17000 ratings: C 101 kN, C0 224 kN, Pu 8.3 kN, reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52312 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 50 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      },
      {
        "q": "Can it replace two single-direction 51-series bearings?",
        "a": "It replaces a mirrored pair functionally — one fit, one housing bore, factory-matched geometry — but its 64 mm height is not twice the single-bearing height and seat details differ, so the housing and cover must be re-drawn rather than swapped in place."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52312",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52312"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52412-M",
    "brand": "SKF",
    "manufacturer_designation": "52412 M",
    "series": "52400-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 130,
    "B_mm": 93,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 199,
    "static_load_kN": 430,
    "fatigue_load_limit_kN": 16,
    "reference_speed_rpm": 1200,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "weight_g": 6350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 52400 series order number 52412 M is a SKF double-direction thrust ball bearing for a 50 mm seat, built to ISO 104, with a flat housing seating surface, 50×130×93 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 50 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 50×130×93 mm (1.969×5.118×3.661 in), 40.0 mm radial section, C 199 kN, C0 430 kN, Pu 16 kN. reference speed 1,200 r/min (thermal) and limiting speed 1,700 r/min (mechanical), catalogue mass 6350 g. Section proportions: the 40.0 mm radial section compares with 50 mm of bore (section/bore ≈ 0.80) and the 93 mm height is 2.33× that section — the proportions that identify the 52400 envelope at a glance. Envelope economics: the 93 mm axial height over a 40.0 mm radial section yields 2.1 kN of dynamic capacity per height millimetre, and the bearing weighs 6350 g for 199 kN C — about 32 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 1,200 r/min against a 1,700 r/min limiting speed, a reference-to-limit ratio of 0.71. Rating split for documentation: dynamic 199 kN (L10 life), static 430 kN (safety factor s0), fatigue limit 16 kN (adjusted life) — three different uses of three different numbers for 52412 M, none interchangeable with another. Track-circle loading: per millimetre of mean track circumference the 199 kN dynamic rating corresponds to roughly 0.70 kN/mm of π·dm track, a useful comparison against the other dimension series of the 50 mm bore. Heavy double-direction note: the M suffix on a 52/54-series bearing means both ball-cage assemblies are machined brass and ball-centred for the largest bidirectional positions; both cage sets share the same lubrication requirement, so the oil or grease feed must reach the upper as well as the lower track on vertical shafts. The M suffix means BOTH cage sets of the 93 mm stack are machined brass; spare-part orders of one side should still be placed as the complete 52412 M unit, because mixed cage executions in one double-direction stack are not a catalogue configuration.",
    "applications": [
      "steering and reversing linkages",
      "elevator machinery thrust positions",
      "reversing gearbox shafts in one compact position"
    ],
    "failure_modes": [
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "assembly damage when the central shaft washer is fitted reversed or the two outward-facing housing washers are swapped",
      "upper brass-cage starvation on a vertical shaft whose lubricant feeds only the lower track pair",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The central shaft washer takes the interference fit on the 50 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52400 unit has no alignment capacity.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 93 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 430 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "The 199/430 kN figures belong to 52412 M specifically (the double flat brass execution of 52412); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52412-M?",
        "a": "Boundary dimensions to ISO 104: bore 50 mm, OD 130 mm, height 93 mm; weight 6350 g. Load figures from SKF 17000: dynamic 199 kN, static 430 kN, fatigue limit 16 kN; reference speed 1,200 r/min (thermal) and limiting speed 1,700 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52412 M mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 50 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      },
      {
        "q": "Can it replace two single-direction 51-series bearings?",
        "a": "It replaces a mirrored pair functionally — one fit, one housing bore, factory-matched geometry — but its 93 mm height is not twice the single-bearing height and seat details differ, so the housing and cover must be re-drawn rather than swapped in place."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52412",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52412-M",
      "52412 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52213",
    "brand": "SKF",
    "manufacturer_designation": "52213",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 60.5,
    "static_load_kN": 150,
    "fatigue_load_limit_kN": 5.5,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 1350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 52200 series order number 52213 is a SKF double-direction thrust ball bearing for a 55 mm seat, built to ISO 104, with a flat housing seating surface, 55×100×47 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 55 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 55×100×47 mm (2.165×3.937×1.85 in), 22.5 mm radial section, C 60.5 kN, C0 150 kN, Pu 5.5 kN. reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical), catalogue mass 1350 g. Speed band width for this size is 800 r/min between reference and limiting (1.40× ratio); lubrication, preload and heat removal decide where inside that band 52213 can actually run. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 2,800 r/min while thermal balance under catalogue load sets the 2,000 r/min reference; at dm ≈ 77.5 mm the corresponding dn is approximately 217k mm·r/min. Sizing arithmetic on the 55 mm bore: 60.5 kN C over the 22.5 mm radial section gives 2.7 kN per section millimetre, and the 47 mm stack height is 2.09× that section — proportions typical of a 52200 thrust section. Capacity density: 60.5 kN C from 1.350 kg of bearing steel gives about 44.8 kN per kilogram; static density is correspondingly 111.1 kN/kg at C0 150 kN. Section proportions: the 22.5 mm radial section compares with 55 mm of bore (section/bore ≈ 0.41) and the 47 mm height is 2.09× that section — the proportions that identify the 52200 envelope at a glance. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52213 is done separately per direction: if duty applies 60.5 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "steering and reversing linkages",
      "machine-tool lead screws and selector shafts",
      "elevator machinery thrust positions"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "cover-induced thrust preload when the end cover is torqued solid instead of leaving the catalogue axial freedom",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 47 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "The double-direction 52213 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 55 mm shaft axially in both directions instead of a mirrored pair.",
      "Each direction independently needs the minimum axial load (factor A 0.14): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 2,800 r/min even a small thermal thrust preload smears the hottest track.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52213 as the double flat pressed steel execution; other order numbers of the 52213 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52213?",
        "a": "Boundary dimensions to ISO 104: bore 55 mm, OD 100 mm, height 47 mm; weight 1350 g. Load figures from SKF 17000: dynamic 60.5 kN, static 150 kN, fatigue limit 5.5 kN; reference speed 2,000 r/min (thermal) and limiting speed 2,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52213 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 55 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "Can it replace two single-direction 51-series bearings?",
        "a": "It replaces a mirrored pair functionally — one fit, one housing bore, factory-matched geometry — but its 47 mm height is not twice the single-bearing height and seat details differ, so the housing and cover must be re-drawn rather than swapped in place."
      },
      {
        "q": "How is a vertical double-direction 52213 lubricated and retained?",
        "a": "Use an oil bath reaching the lower track plus a feed or oil level that serves the upper cage set, or a coherent heavy-base grease; positively retain both loose housing washers because gravity loads the upper stack differently at standstill."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52213",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52213"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52214",
    "brand": "SKF",
    "manufacturer_designation": "52214",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 105,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 62.4,
    "static_load_kN": 160,
    "fatigue_load_limit_kN": 5.85,
    "reference_speed_rpm": 1900,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 1500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52214 is SKF's 55 mm-bore double-direction thrust ball bearing in the 52200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 55×105×47 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 55 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 55×105×47 mm (2.165×4.134×1.85 in), 25.0 mm radial section, C 62.4 kN, C0 160 kN, Pu 5.85 kN. reference speed 1,900 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 1500 g. Light-load floor: Pu = 5.85 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52214; the number is 9 % of the 62.4 kN dynamic rating. Stack/annulus proportions: the 47 mm axial stack over the 6,283 mm² washer annulus gives 7.48 mm of height per annular square millimetre ×10⁻³, and at 1500 g the bearing holds about 106.7 kN of C0 per kilogram. Section proportions: the 25.0 mm radial section compares with 55 mm of bore (section/bore ≈ 0.45) and the 47 mm height is 1.88× that section — the proportions that identify the 52200 envelope at a glance. Speed band width for this size is 700 r/min between reference and limiting (1.37× ratio); lubrication, preload and heat removal decide where inside that band 52214 can actually run. Envelope economics: the 47 mm axial height over a 25.0 mm radial section yields 1.3 kN of dynamic capacity per height millimetre, and the bearing weighs 1500 g for 62.4 kN C — about 24 g per rated kN. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 55 mm bore and 47 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 105 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "reversing gearbox shafts in one compact position",
      "elevator machinery thrust positions",
      "vertical pumps with intermittent up-thrust"
    ],
    "failure_modes": [
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Each direction independently needs the minimum axial load (factor A 0.16): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "The central shaft washer takes the interference fit on the 55 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 160 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Do not replace a 52214 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 55×105 mm bore and OD.",
      "The 62.4/160 kN figures belong to 52214 specifically (the double flat pressed steel execution of 52214); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52214?",
        "a": "52214 measures 55 mm bore × 105 mm OD × 47 mm bearing height (2.165 × 4.134 × 1.85 in), mass about 1500 g. SKF 17000 ratings: C 62.4 kN, C0 160 kN, Pu 5.85 kN, reference speed 1,900 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52214 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 55 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "What minimum axial load applies to a double-direction bearing?",
        "a": "The Fam ≈ A·(n·dm/1000)² rule (factor A 0.16) applies to EACH direction: the momentarily unloaded side during slow reversal is the one that skids, so preload or balanced loading must keep both ball sets seated."
      },
      {
        "q": "How is the double-direction 52214 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 55×105×47 mm unit locating the shaft axially in both directions."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52214",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52214"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52313",
    "brand": "SKF",
    "manufacturer_designation": "52313",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 115,
    "B_mm": 64,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 106,
    "static_load_kN": 240,
    "fatigue_load_limit_kN": 8.8,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 2750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52313 is SKF's 55 mm-bore double-direction thrust ball bearing in the 52300 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 55×115×64 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 55 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 55×115×64 mm (2.165×4.528×2.52 in), 30.0 mm radial section, C 106 kN, C0 240 kN, Pu 8.8 kN. reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 2750 g. Selection figures for 52313: the C0/C ratio is 2.26, Pu 8.8 kN is about 8 % of C, and the catalogue mass works out to roughly 50 g per millimetre of bore; the printed minimum-load factor is A 0.3. Pitch-diameter arithmetic: dm = (55+115)/2 = 85.0 mm; at the 2,200 r/min limiting speed that corresponds to roughly 187k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Mass and section check: 2750 g inside the 55×115×64 mm outline leaves a 30.0 mm radial section, and the 240 kN static rating is 2.26× the dynamic rating — plan static safety and minimum preload against those figures. Minimum-load arithmetic: with dm ≈ 85.0 mm and factor A 0.3, Fam ≈ A·(n·dm/1000)² at the 1,600 r/min reference speed is about 5.5 kN for 52313; below that preload the balls skid and smear the tracks. Section proportions: the 30.0 mm radial section compares with 55 mm of bore (section/bore ≈ 0.55) and the 64 mm height is 2.13× that section — the proportions that identify the 52300 envelope at a glance. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52313 is done separately per direction: if duty applies 106 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "machine-tool lead screws and selector shafts",
      "steering and reversing linkages",
      "vertical pumps with intermittent up-thrust"
    ],
    "failure_modes": [
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Service both cage sets together: replacing only the noisy side while leaving the worn 240 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 64 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "The double-direction 52313 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 55 mm shaft axially in both directions instead of a mirrored pair.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52300 unit has no alignment capacity.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52313 as the double flat pressed steel execution; other order numbers of the 52313 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52313?",
        "a": "52313 measures 55 mm bore × 115 mm OD × 64 mm bearing height (2.165 × 4.528 × 2.52 in), mass about 2750 g. SKF 17000 ratings: C 106 kN, C0 240 kN, Pu 8.8 kN, reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52313 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 55 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "Which fits and retention does 52313 need?",
        "a": "The central shaft washer takes an interference fit on the 55 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      },
      {
        "q": "What static check governs crane-hook duty for 52313?",
        "a": "Hook and screw positions are usually sized on C0 (240 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 106 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52313",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52313"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52314",
    "brand": "SKF",
    "manufacturer_designation": "52314",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 125,
    "B_mm": 72,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 135,
    "static_load_kN": 320,
    "fatigue_load_limit_kN": 11.8,
    "reference_speed_rpm": 1400,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "weight_g": 3650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52314 is an ISO 104 double-direction thrust ball bearing, 55 mm bore and 125 mm OD on a flat housing seat, standing 72 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52314 is 55 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 55×125×72 mm (2.165×4.921×2.835 in), 35.0 mm radial section, C 135 kN, C0 320 kN, Pu 11.8 kN. reference speed 1,400 r/min (thermal) and limiting speed 2,000 r/min (mechanical), catalogue mass 3650 g. Static-first selection data: 320 kN C0 spread across the 72 mm stack gives 4.4 kN of static rating per height millimetre, and the 3650 g mass/C0 ratio is about 11 g per static kN — crane-hook and screw positions are normally sized on these two figures. Envelope economics: the 72 mm axial height over a 35.0 mm radial section yields 1.9 kN of dynamic capacity per height millimetre, and the bearing weighs 3650 g for 135 kN C — about 27 g per rated kN. Washer-annulus check: the π/4·(D²−d²) contact annulus of 52314 covers about 9,896 mm², distributing C0 320 kN over a mean track circle of π·dm ≈ 283 mm. Minimum-load arithmetic: with dm ≈ 90.0 mm and factor A 0.53, Fam ≈ A·(n·dm/1000)² at the 1,400 r/min reference speed is about 8.4 kN for 52314; below that preload the balls skid and smear the tracks. Imperial cross-check for procurement drawings: 2.165 in bore, 4.921 in OD, 2.835 in height, and the 3650 g catalogue mass converts to 3.650 kg (128.7 oz). Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 55 mm bore and 72 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 125 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "steering and reversing linkages",
      "machine-tool lead screws and selector shafts",
      "reversing gearbox shafts in one compact position"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Service both cage sets together: replacing only the noisy side while leaving the worn 320 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 72 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52300 unit has no alignment capacity.",
      "Do not replace a 52314 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 55×125 mm bore and OD.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52314 as the double flat pressed steel execution; other order numbers of the 52314 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52314?",
        "a": "The catalogue envelope is 55×125×72 mm, mass 3650 g; ratings C 135 kN / C0 320 kN / Pu 11.8 kN, reference speed 1,400 r/min (thermal) and limiting speed 2,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52314 mean?",
        "a": "note the bore of 52314 is 55 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "What minimum axial load applies to a double-direction bearing?",
        "a": "The Fam ≈ A·(n·dm/1000)² rule (factor A 0.53) applies to EACH direction: the momentarily unloaded side during slow reversal is the one that skids, so preload or balanced loading must keep both ball sets seated."
      },
      {
        "q": "How is the double-direction 52314 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 55×125×72 mm unit locating the shaft axially in both directions."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52314",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52314"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52414-M",
    "brand": "SKF",
    "manufacturer_designation": "52414 M",
    "series": "52400-series",
    "type": "thrust_ball",
    "d_mm": 55,
    "D_mm": 250,
    "B_mm": 107,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 234,
    "static_load_kN": 550,
    "fatigue_load_limit_kN": 19.3,
    "reference_speed_rpm": 800,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "weight_g": 9700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52414 M is an ISO 104 double-direction thrust ball bearing, 55 mm bore and 250 mm OD on a flat housing seat, standing 107 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52414 M is 55 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 55×250×107 mm (2.165×9.843×4.213 in), 97.5 mm radial section, C 234 kN, C0 550 kN, Pu 19.3 kN. reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical), catalogue mass 9700 g. Capacity density: 234 kN C from 9.700 kg of bearing steel gives about 24.1 kN per kilogram; static density is correspondingly 56.7 kN/kg at C0 550 kN. Bore-to-OD planning: OD 250 over bore 55 is a 4.55× step for this size, and the 107 mm height gives a bore/height ratio of 0.51; use these ratios when the housing recess around the 55 mm shaft is the first constraint. Pitch-diameter arithmetic: dm = (55+250)/2 = 152.5 mm; at the 1,100 r/min limiting speed that corresponds to roughly 168k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Light-load floor: Pu = 19.3 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52414 M; the number is 8 % of the 234 kN dynamic rating. Section proportions: the 97.5 mm radial section compares with 55 mm of bore (section/bore ≈ 1.77) and the 107 mm height is 1.10× that section — the proportions that identify the 52400 envelope at a glance. Heavy double-direction note: the M suffix on a 52/54-series bearing means both ball-cage assemblies are machined brass and ball-centred for the largest bidirectional positions; both cage sets share the same lubrication requirement, so the oil or grease feed must reach the upper as well as the lower track on vertical shafts. With 9700 g rotating partially with the shaft, check the rotor-balance influence of the central shaft washer at speeds approaching 1,100 r/min; the two loose washers do not rotate and contribute no imbalance.",
    "applications": [
      "reversing gearbox shafts in one compact position",
      "steering and reversing linkages",
      "machine-tool lead screws and selector shafts"
    ],
    "failure_modes": [
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "upper brass-cage starvation on a vertical shaft whose lubricant feeds only the lower track pair",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 1,100 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 550 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Do not replace a 52414 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 55×250 mm bore and OD.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52400 unit has no alignment capacity.",
      "The 234/550 kN figures belong to 52414 M specifically (the double flat brass execution of 52414); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52414-M?",
        "a": "The catalogue envelope is 55×250×107 mm, mass 9700 g; ratings C 234 kN / C0 550 kN / Pu 19.3 kN, reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52414 M mean?",
        "a": "note the bore of 52414 M is 55 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is a vertical double-direction 52414 lubricated and retained?",
        "a": "Use an oil bath reaching the lower track plus a feed or oil level that serves the upper cage set, or a coherent heavy-base grease; positively retain both loose housing washers because gravity loads the upper stack differently at standstill."
      },
      {
        "q": "Which fits and retention does 52414-M need?",
        "a": "The central shaft washer takes an interference fit on the 55 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52414",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52414-M",
      "52414 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52215",
    "brand": "SKF",
    "manufacturer_designation": "52215",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 63.7,
    "static_load_kN": 170,
    "fatigue_load_limit_kN": 6.2,
    "reference_speed_rpm": 1900,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 1550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52215 is SKF's 60 mm-bore double-direction thrust ball bearing in the 52200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 60×110×47 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 60 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 60×110×47 mm (2.362×4.331×1.85 in), 25.0 mm radial section, C 63.7 kN, C0 170 kN, Pu 6.2 kN. reference speed 1,900 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 1550 g. Pitch-diameter arithmetic: dm = (60+110)/2 = 85.0 mm; at the 2,600 r/min limiting speed that corresponds to roughly 221k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Track-circle loading: per millimetre of mean track circumference the 63.7 kN dynamic rating corresponds to roughly 0.24 kN/mm of π·dm track, a useful comparison against the other dimension series of the 60 mm bore. Speed band width for this size is 700 r/min between reference and limiting (1.37× ratio); lubrication, preload and heat removal decide where inside that band 52215 can actually run. Light-load floor: Pu = 6.2 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52215; the number is 10 % of the 63.7 kN dynamic rating. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 2,600 r/min while thermal balance under catalogue load sets the 1,900 r/min reference; at dm ≈ 85.0 mm the corresponding dn is approximately 221k mm·r/min. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52215 is done separately per direction: if duty applies 63.7 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "crane travel and slewing drives",
      "heavy reversing gearbox shafts",
      "large lead-screw and press adjustment"
    ],
    "failure_modes": [
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 47 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "The double-direction 52215 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 60 mm shaft axially in both directions instead of a mirrored pair.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 2,600 r/min even a small thermal thrust preload smears the hottest track.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52215 as the double flat pressed steel execution; other order numbers of the 52215 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52215?",
        "a": "52215 measures 60 mm bore × 110 mm OD × 47 mm bearing height (2.362 × 4.331 × 1.85 in), mass about 1550 g. SKF 17000 ratings: C 63.7 kN, C0 170 kN, Pu 6.2 kN, reference speed 1,900 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52215 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 60 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is the double-direction 52215 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 60×110×47 mm unit locating the shaft axially in both directions."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52215",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52215"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52315",
    "brand": "SKF",
    "manufacturer_designation": "52315",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 60,
    "D_mm": 135,
    "B_mm": 79,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 163,
    "static_load_kN": 390,
    "fatigue_load_limit_kN": 14,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "weight_g": 4800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 52300 series order number 52315 is a SKF double-direction thrust ball bearing for a 60 mm seat, built to ISO 104, with a flat housing seating surface, 60×135×79 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 60 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 60×135×79 mm (2.362×5.315×3.11 in), 37.5 mm radial section, C 163 kN, C0 390 kN, Pu 14 kN. reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical), catalogue mass 4800 g. Minimum-load arithmetic: with dm ≈ 97.5 mm and factor A 0.79, Fam ≈ A·(n·dm/1000)² at the 1,300 r/min reference speed is about 12.7 kN for 52315; below that preload the balls skid and smear the tracks. Rating split for documentation: dynamic 163 kN (L10 life), static 390 kN (safety factor s0), fatigue limit 14 kN (adjusted life) — three different uses of three different numbers for 52315, none interchangeable with another. Track-circle loading: per millimetre of mean track circumference the 163 kN dynamic rating corresponds to roughly 0.53 kN/mm of π·dm track, a useful comparison against the other dimension series of the 60 mm bore. Section proportions: the 37.5 mm radial section compares with 60 mm of bore (section/bore ≈ 0.63) and the 79 mm height is 2.11× that section — the proportions that identify the 52300 envelope at a glance. Speed band width for this size is 500 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 52315 can actually run. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 60 mm bore and 79 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 135 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "large lead-screw and press adjustment",
      "winch and hoist reversal positions",
      "heavy reversing gearbox shafts"
    ],
    "failure_modes": [
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "assembly damage when the central shaft washer is fitted reversed or the two outward-facing housing washers are swapped",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Each direction independently needs the minimum axial load (factor A 0.79): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "The central shaft washer takes the interference fit on the 60 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Do not replace a 52315 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 60×135 mm bore and OD.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 79 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "The 163/390 kN figures belong to 52315 specifically (the double flat pressed steel execution of 52315); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52315?",
        "a": "Boundary dimensions to ISO 104: bore 60 mm, OD 135 mm, height 79 mm; weight 4800 g. Load figures from SKF 17000: dynamic 163 kN, static 390 kN, fatigue limit 14 kN; reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52315 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 60 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "Which fits and retention does 52315 need?",
        "a": "The central shaft washer takes an interference fit on the 60 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      },
      {
        "q": "What static check governs crane-hook duty for 52315?",
        "a": "Hook and screw positions are usually sized on C0 (390 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 163 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52315",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52315"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52216",
    "brand": "SKF",
    "manufacturer_designation": "52216",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 115,
    "B_mm": 48,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 76.1,
    "static_load_kN": 208,
    "fatigue_load_limit_kN": 7.65,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 1700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 52200 series order number 52216 is a SKF double-direction thrust ball bearing for a 65 mm seat, built to ISO 104, with a flat housing seating surface, 65×115×48 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 65 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 65×115×48 mm (2.559×4.528×1.89 in), 25.0 mm radial section, C 76.1 kN, C0 208 kN, Pu 7.65 kN. reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 1700 g. Light-load floor: Pu = 7.65 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52216; the number is 10 % of the 76.1 kN dynamic rating. Load balance: C0 208 kN against C 76.1 kN gives a 2.73 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 7.65 kN enters the adjusted-life check. Section proportions: the 25.0 mm radial section compares with 65 mm of bore (section/bore ≈ 0.38) and the 48 mm height is 1.92× that section — the proportions that identify the 52200 envelope at a glance. Sizing arithmetic on the 65 mm bore: 76.1 kN C over the 25.0 mm radial section gives 3.0 kN per section millimetre, and the 48 mm stack height is 1.92× that section — proportions typical of a 52200 thrust section. Imperial cross-check for procurement drawings: 2.559 in bore, 4.528 in OD, 1.89 in height, and the 1700 g catalogue mass converts to 1.700 kg (60.0 oz). Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 65 mm bore and 48 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 115 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "heavy reversing gearbox shafts",
      "vertical motors subject to start-up up-thrust",
      "large lead-screw and press adjustment"
    ],
    "failure_modes": [
      "cover-induced thrust preload when the end cover is torqued solid instead of leaving the catalogue axial freedom",
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "track rust staining from condensate during long idle periods in humid plant air",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Each direction independently needs the minimum axial load (factor A 0.22): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "The central shaft washer takes the interference fit on the 65 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "The double-direction 52216 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 65 mm shaft axially in both directions instead of a mirrored pair.",
      "Do not replace a 52216 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 65×115 mm bore and OD.",
      "Ordering discipline for 52216: the catalogue page quotes 52216 and its 76.1/208 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52216?",
        "a": "Boundary dimensions to ISO 104: bore 65 mm, OD 115 mm, height 48 mm; weight 1700 g. Load figures from SKF 17000: dynamic 76.1 kN, static 208 kN, fatigue limit 7.65 kN; reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52216 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 65 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "What minimum axial load applies to a double-direction bearing?",
        "a": "The Fam ≈ A·(n·dm/1000)² rule (factor A 0.22) applies to EACH direction: the momentarily unloaded side during slow reversal is the one that skids, so preload or balanced loading must keep both ball sets seated."
      },
      {
        "q": "How is the double-direction 52216 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 65×115×48 mm unit locating the shaft axially in both directions."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52216",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52216"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52316",
    "brand": "SKF",
    "manufacturer_designation": "52316",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 79,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 159,
    "static_load_kN": 390,
    "fatigue_load_limit_kN": 13.7,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "weight_g": 4950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52316 is an ISO 104 double-direction thrust ball bearing, 65 mm bore and 140 mm OD on a flat housing seat, standing 79 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52316 is 65 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 65×140×79 mm (2.559×5.512×3.11 in), 37.5 mm radial section, C 159 kN, C0 390 kN, Pu 13.7 kN. reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical), catalogue mass 4950 g. Washer-annulus check: the π/4·(D²−d²) contact annulus of 52316 covers about 12,075 mm², distributing C0 390 kN over a mean track circle of π·dm ≈ 322 mm. Section proportions: the 37.5 mm radial section compares with 65 mm of bore (section/bore ≈ 0.58) and the 79 mm height is 2.11× that section — the proportions that identify the 52300 envelope at a glance. Selection figures for 52316: the C0/C ratio is 2.45, Pu 13.7 kN is about 9 % of C, and the catalogue mass works out to roughly 76 g per millimetre of bore; the printed minimum-load factor is A 0.79. Mass and section check: 4950 g inside the 65×140×79 mm outline leaves a 37.5 mm radial section, and the 390 kN static rating is 2.45× the dynamic rating — plan static safety and minimum preload against those figures. Static-first selection data: 390 kN C0 spread across the 79 mm stack gives 4.9 kN of static rating per height millimetre, and the 4950 g mass/C0 ratio is about 13 g per static kN — crane-hook and screw positions are normally sized on these two figures. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 65 mm bore and 79 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 140 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "heavy reversing gearbox shafts",
      "winch and hoist reversal positions",
      "vertical motors subject to start-up up-thrust"
    ],
    "failure_modes": [
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The double-direction 52316 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 65 mm shaft axially in both directions instead of a mirrored pair.",
      "Each direction independently needs the minimum axial load (factor A 0.79): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "The central shaft washer takes the interference fit on the 65 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 1,800 r/min even a small thermal thrust preload smears the hottest track.",
      "The 159/390 kN figures belong to 52316 specifically (the double flat pressed steel execution of 52316); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52316?",
        "a": "The catalogue envelope is 65×140×79 mm, mass 4950 g; ratings C 159 kN / C0 390 kN / Pu 13.7 kN, reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52316 mean?",
        "a": "note the bore of 52316 is 65 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "What static check governs crane-hook duty for 52316?",
        "a": "Hook and screw positions are usually sized on C0 (390 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 159 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      },
      {
        "q": "What minimum axial load applies to a double-direction bearing?",
        "a": "The Fam ≈ A·(n·dm/1000)² rule (factor A 0.79) applies to EACH direction: the momentarily unloaded side during slow reversal is the one that skids, so preload or balanced loading must keep both ball sets seated."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52316",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52316"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52217",
    "brand": "SKF",
    "manufacturer_designation": "52217",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 97.5,
    "static_load_kN": 275,
    "fatigue_load_limit_kN": 9.8,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 2400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 52200 series order number 52217 is a SKF double-direction thrust ball bearing for a 70 mm seat, built to ISO 104, with a flat housing seating surface, 70×125×55 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 70 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 70×125×55 mm (2.756×4.921×2.165 in), 27.5 mm radial section, C 97.5 kN, C0 275 kN, Pu 9.8 kN. reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 2400 g. Stack/annulus proportions: the 55 mm axial stack over the 8,423 mm² washer annulus gives 6.53 mm of height per annular square millimetre ×10⁻³, and at 2400 g the bearing holds about 114.6 kN of C0 per kilogram. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 2,200 r/min while thermal balance under catalogue load sets the 1,600 r/min reference; at dm ≈ 97.5 mm the corresponding dn is approximately 215k mm·r/min. Pitch-diameter arithmetic: dm = (70+125)/2 = 97.5 mm; at the 2,200 r/min limiting speed that corresponds to roughly 215k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Section proportions: the 27.5 mm radial section compares with 70 mm of bore (section/bore ≈ 0.39) and the 55 mm height is 2.00× that section — the proportions that identify the 52200 envelope at a glance. Speed band width for this size is 600 r/min between reference and limiting (1.38× ratio); lubrication, preload and heat removal decide where inside that band 52217 can actually run. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52217 is done separately per direction: if duty applies 97.5 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "vertical motors subject to start-up up-thrust",
      "large lead-screw and press adjustment",
      "winch and hoist reversal positions"
    ],
    "failure_modes": [
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "assembly damage when the central shaft washer is fitted reversed or the two outward-facing housing washers are swapped",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 2,200 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 275 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Do not replace a 52217 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 70×125 mm bore and OD.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "The 97.5/275 kN figures belong to 52217 specifically (the double flat pressed steel execution of 52217); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52217?",
        "a": "Boundary dimensions to ISO 104: bore 70 mm, OD 125 mm, height 55 mm; weight 2400 g. Load figures from SKF 17000: dynamic 97.5 kN, static 275 kN, fatigue limit 9.8 kN; reference speed 1,600 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52217 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 70 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      },
      {
        "q": "Can it replace two single-direction 51-series bearings?",
        "a": "It replaces a mirrored pair functionally — one fit, one housing bore, factory-matched geometry — but its 55 mm height is not twice the single-bearing height and seat details differ, so the housing and cover must be re-drawn rather than swapped in place."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52217",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52217"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52218",
    "brand": "SKF",
    "manufacturer_designation": "52218",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 75,
    "D_mm": 135,
    "B_mm": 62,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 112,
    "static_load_kN": 290,
    "fatigue_load_limit_kN": 11.6,
    "reference_speed_rpm": 1500,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "weight_g": 3200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52218 is an ISO 104 double-direction thrust ball bearing, 75 mm bore and 135 mm OD on a flat housing seat, standing 62 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52218 is 75 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 75×135×62 mm (2.953×5.315×2.441 in), 30.0 mm radial section, C 112 kN, C0 290 kN, Pu 11.6 kN. reference speed 1,500 r/min (thermal) and limiting speed 2,000 r/min (mechanical), catalogue mass 3200 g. Bore-to-OD planning: OD 135 over bore 75 is a 1.80× step for this size, and the 62 mm height gives a bore/height ratio of 1.21; use these ratios when the housing recess around the 75 mm shaft is the first constraint. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.55 at the 2,000 r/min limiting speed raises the required axial preload to about 24.3 kN; the reference-speed value 13.6 kN is the thermal design point. Mass and section check: 3200 g inside the 75×135×62 mm outline leaves a 30.0 mm radial section, and the 290 kN static rating is 2.59× the dynamic rating — plan static safety and minimum preload against those figures. Load balance: C0 290 kN against C 112 kN gives a 2.59 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 11.6 kN enters the adjusted-life check. Light-load floor: Pu = 11.6 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52218; the number is 10 % of the 112 kN dynamic rating. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52218 is done separately per direction: if duty applies 112 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "crane travel and slewing drives",
      "winch and hoist reversal positions",
      "large lead-screw and press adjustment"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "The central shaft washer takes the interference fit on the 75 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 290 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 62 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52218 as the double flat pressed steel execution; other order numbers of the 52218 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52218?",
        "a": "The catalogue envelope is 75×135×62 mm, mass 3200 g; ratings C 112 kN / C0 290 kN / Pu 11.6 kN, reference speed 1,500 r/min (thermal) and limiting speed 2,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52218 mean?",
        "a": "note the bore of 52218 is 75 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is a vertical double-direction 52218 lubricated and retained?",
        "a": "Use an oil bath reaching the lower track plus a feed or oil level that serves the upper cage set, or a coherent heavy-base grease; positively retain both loose housing washers because gravity loads the upper stack differently at standstill."
      },
      {
        "q": "Which fits and retention does 52218 need?",
        "a": "The central shaft washer takes an interference fit on the 75 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52218",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52218"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52220",
    "brand": "SKF",
    "manufacturer_designation": "52220",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 67,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 119,
    "static_load_kN": 325,
    "fatigue_load_limit_kN": 10.8,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "weight_g": 4200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 52200 series order number 52220 is a SKF double-direction thrust ball bearing for a 85 mm seat, built to ISO 104, with a flat housing seating surface, 85×150×67 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 85 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 85×150×67 mm (3.346×5.906×2.638 in), 32.5 mm radial section, C 119 kN, C0 325 kN, Pu 10.8 kN. reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical), catalogue mass 4200 g. Imperial cross-check for procurement drawings: 3.346 in bore, 5.906 in OD, 2.638 in height, and the 4200 g catalogue mass converts to 4.200 kg (148.1 oz). Speed-ratio note for this exact unit: the reference speed is 1,300 r/min against a 1,800 r/min limiting speed, a reference-to-limit ratio of 0.72. Bore-to-OD planning: OD 150 over bore 85 is a 1.76× step for this size, and the 67 mm height gives a bore/height ratio of 1.27; use these ratios when the housing recess around the 85 mm shaft is the first constraint. Light-load floor: Pu = 10.8 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52220; the number is 9 % of the 119 kN dynamic rating. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.62 at the 1,800 r/min limiting speed raises the required axial preload to about 27.7 kN; the reference-speed value 14.5 kN is the thermal design point. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 85 mm bore and 67 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 150 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "heavy reversing gearbox shafts",
      "vertical motors subject to start-up up-thrust",
      "winch and hoist reversal positions"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "washer face scoring from swarf trapped between the loose housing washer and its register"
    ],
    "pitfalls": [
      "Service both cage sets together: replacing only the noisy side while leaving the worn 325 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 67 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Do not replace a 52220 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 85×150 mm bore and OD.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52220 as the double flat pressed steel execution; other order numbers of the 52220 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52220?",
        "a": "Boundary dimensions to ISO 104: bore 85 mm, OD 150 mm, height 67 mm; weight 4200 g. Load figures from SKF 17000: dynamic 119 kN, static 325 kN, fatigue limit 10.8 kN; reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52220 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 85 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "What static check governs crane-hook duty for 52220?",
        "a": "Hook and screw positions are usually sized on C0 (325 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 119 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      },
      {
        "q": "What minimum axial load applies to a double-direction bearing?",
        "a": "The Fam ≈ A·(n·dm/1000)² rule (factor A 0.62) applies to EACH direction: the momentarily unloaded side during slow reversal is the one that skids, so preload or balanced loading must keep both ball sets seated."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52220",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52220"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52320",
    "brand": "SKF",
    "manufacturer_designation": "52320",
    "series": "52300-series",
    "type": "thrust_ball",
    "d_mm": 85,
    "D_mm": 170,
    "B_mm": 97,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 225,
    "static_load_kN": 570,
    "fatigue_load_limit_kN": 18.3,
    "reference_speed_rpm": 1000,
    "limiting_speed_rpm": 1400,
    "max_rpm": 1400,
    "weight_g": 8950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52320 is an ISO 104 double-direction thrust ball bearing, 85 mm bore and 170 mm OD on a flat housing seat, standing 97 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52320 is 85 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 85×170×97 mm (3.346×6.693×3.819 in), 42.5 mm radial section, C 225 kN, C0 570 kN, Pu 18.3 kN. reference speed 1,000 r/min (thermal) and limiting speed 1,400 r/min (mechanical), catalogue mass 8950 g. Sizing arithmetic on the 85 mm bore: 225 kN C over the 42.5 mm radial section gives 5.3 kN per section millimetre, and the 97 mm stack height is 2.28× that section — proportions typical of a 52300 thrust section. Speed band width for this size is 400 r/min between reference and limiting (1.40× ratio); lubrication, preload and heat removal decide where inside that band 52320 can actually run. Imperial cross-check for procurement drawings: 3.346 in bore, 6.693 in OD, 3.819 in height, and the 8950 g catalogue mass converts to 8.950 kg (315.7 oz). Load balance: C0 570 kN against C 225 kN gives a 2.53 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 18.3 kN enters the adjusted-life check. Envelope economics: the 97 mm axial height over a 42.5 mm radial section yields 2.3 kN of dynamic capacity per height millimetre, and the bearing weighs 8950 g for 225 kN C — about 40 g per rated kN. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 85 mm bore and 97 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 170 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "crane travel and slewing drives",
      "large lead-screw and press adjustment",
      "winch and hoist reversal positions"
    ],
    "failure_modes": [
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Each direction independently needs the minimum axial load (factor A 1.9): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "The central shaft washer takes the interference fit on the 85 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 570 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Do not replace a 52320 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 85×170 mm bore and OD.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52320 as the double flat pressed steel execution; other order numbers of the 52320 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52320?",
        "a": "The catalogue envelope is 85×170×97 mm, mass 8950 g; ratings C 225 kN / C0 570 kN / Pu 18.3 kN, reference speed 1,000 r/min (thermal) and limiting speed 1,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52320 mean?",
        "a": "note the bore of 52320 is 85 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      },
      {
        "q": "Can it replace two single-direction 51-series bearings?",
        "a": "It replaces a mirrored pair functionally — one fit, one housing bore, factory-matched geometry — but its 97 mm height is not twice the single-bearing height and seat details differ, so the housing and cover must be re-drawn rather than swapped in place."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52320",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52320"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52222",
    "brand": "SKF",
    "manufacturer_designation": "52222",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 95,
    "D_mm": 160,
    "B_mm": 67,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 125,
    "static_load_kN": 365,
    "fatigue_load_limit_kN": 11.6,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "weight_g": 4650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52222 is an ISO 104 double-direction thrust ball bearing, 95 mm bore and 160 mm OD on a flat housing seat, standing 67 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52222 is 95 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 95×160×67 mm (3.74×6.299×2.638 in), 32.5 mm radial section, C 125 kN, C0 365 kN, Pu 11.6 kN. reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical), catalogue mass 4650 g. Sizing arithmetic on the 95 mm bore: 125 kN C over the 32.5 mm radial section gives 3.8 kN per section millimetre, and the 67 mm stack height is 2.06× that section — proportions typical of a 52200 thrust section. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 1,800 r/min while thermal balance under catalogue load sets the 1,300 r/min reference; at dm ≈ 127.5 mm the corresponding dn is approximately 230k mm·r/min. Minimum-load arithmetic: with dm ≈ 127.5 mm and factor A 0.79, Fam ≈ A·(n·dm/1000)² at the 1,300 r/min reference speed is about 21.7 kN for 52222; below that preload the balls skid and smear the tracks. Stack/annulus proportions: the 67 mm axial stack over the 13,018 mm² washer annulus gives 5.15 mm of height per annular square millimetre ×10⁻³, and at 4650 g the bearing holds about 78.5 kN of C0 per kilogram. Envelope economics: the 67 mm axial height over a 32.5 mm radial section yields 1.9 kN of dynamic capacity per height millimetre, and the bearing weighs 4650 g for 125 kN C — about 37 g per rated kN. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52222 is done separately per direction: if duty applies 125 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "crane travel and slewing drives",
      "winch and hoist reversal positions",
      "large lead-screw and press adjustment"
    ],
    "failure_modes": [
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 67 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "The double-direction 52222 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 95 mm shaft axially in both directions instead of a mirrored pair.",
      "Each direction independently needs the minimum axial load (factor A 0.79): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 1,800 r/min even a small thermal thrust preload smears the hottest track.",
      "The 125/365 kN figures belong to 52222 specifically (the double flat pressed steel execution of 52222); suffixed, sphered and counterpart-series order numbers are separate articles, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52222?",
        "a": "The catalogue envelope is 95×160×67 mm, mass 4650 g; ratings C 125 kN / C0 365 kN / Pu 11.6 kN, reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52222 mean?",
        "a": "note the bore of 52222 is 95 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is the double-direction 52222 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 95×160×67 mm unit locating the shaft axially in both directions."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52222",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52222"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52224",
    "brand": "SKF",
    "manufacturer_designation": "52224",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 100,
    "D_mm": 170,
    "B_mm": 68,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 127,
    "static_load_kN": 390,
    "fatigue_load_limit_kN": 11.8,
    "reference_speed_rpm": 1200,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "weight_g": 5250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52224 is an ISO 104 double-direction thrust ball bearing, 100 mm bore and 170 mm OD on a flat housing seat, standing 68 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52224 is 100 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 100×170×68 mm (3.937×6.693×2.677 in), 35.0 mm radial section, C 127 kN, C0 390 kN, Pu 11.8 kN. reference speed 1,200 r/min (thermal) and limiting speed 1,700 r/min (mechanical), catalogue mass 5250 g. Section proportions: the 35.0 mm radial section compares with 100 mm of bore (section/bore ≈ 0.35) and the 68 mm height is 1.94× that section — the proportions that identify the 52200 envelope at a glance. Selection figures for 52224: the C0/C ratio is 3.07, Pu 11.8 kN is about 9 % of C, and the catalogue mass works out to roughly 53 g per millimetre of bore; the printed minimum-load factor is A 1. Imperial cross-check for procurement drawings: 3.937 in bore, 6.693 in OD, 2.677 in height, and the 5250 g catalogue mass converts to 5.250 kg (185.2 oz). Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 1 at the 1,700 r/min limiting speed raises the required axial preload to about 52.7 kN; the reference-speed value 26.2 kN is the thermal design point. Mass and section check: 5250 g inside the 100×170×68 mm outline leaves a 35.0 mm radial section, and the 390 kN static rating is 3.07× the dynamic rating — plan static safety and minimum preload against those figures. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. At 100 mm bore and 68 mm overall height the unit drops into one recess where a mirrored single-direction pair would need two seats; both loose 170 mm housing washers must remain free to slide during thermal movement.",
    "applications": [
      "heavy reversing gearbox shafts",
      "winch and hoist reversal positions",
      "crane travel and slewing drives"
    ],
    "failure_modes": [
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume"
    ],
    "pitfalls": [
      "Service both cage sets together: replacing only the noisy side while leaving the worn 390 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 68 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Do not replace a 52224 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 100×170 mm bore and OD.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52224 as the double flat pressed steel execution; other order numbers of the 52224 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52224?",
        "a": "The catalogue envelope is 100×170×68 mm, mass 5250 g; ratings C 127 kN / C0 390 kN / Pu 11.8 kN, reference speed 1,200 r/min (thermal) and limiting speed 1,700 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52224 mean?",
        "a": "note the bore of 52224 is 100 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "Which fits and retention does 52224 need?",
        "a": "The central shaft washer takes an interference fit on the 100 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      },
      {
        "q": "What static check governs crane-hook duty for 52224?",
        "a": "Hook and screw positions are usually sized on C0 (390 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 127 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52224",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52224"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52226",
    "brand": "SKF",
    "manufacturer_designation": "52226",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 110,
    "D_mm": 190,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 182,
    "static_load_kN": 585,
    "fatigue_load_limit_kN": 16.6,
    "reference_speed_rpm": 1100,
    "limiting_speed_rpm": 1500,
    "max_rpm": 1500,
    "weight_g": 8000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52226 is an ISO 104 double-direction thrust ball bearing, 110 mm bore and 190 mm OD on a flat housing seat, standing 80 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52226 is 110 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 110×190×80 mm (4.331×7.48×3.15 in), 40.0 mm radial section, C 182 kN, C0 585 kN, Pu 16.6 kN. reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical), catalogue mass 8000 g. Speed band width for this size is 400 r/min between reference and limiting (1.36× ratio); lubrication, preload and heat removal decide where inside that band 52226 can actually run. Track-circle loading: per millimetre of mean track circumference the 182 kN dynamic rating corresponds to roughly 0.39 kN/mm of π·dm track, a useful comparison against the other dimension series of the 110 mm bore. Mass and section check: 8000 g inside the 110×190×80 mm outline leaves a 40.0 mm radial section, and the 585 kN static rating is 3.21× the dynamic rating — plan static safety and minimum preload against those figures. Pitch-diameter arithmetic: dm = (110+190)/2 = 150.0 mm; at the 1,500 r/min limiting speed that corresponds to roughly 225k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Imperial cross-check for procurement drawings: 4.331 in bore, 7.48 in OD, 3.15 in height, and the 8000 g catalogue mass converts to 8.000 kg (282.2 oz). Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52226 is done separately per direction: if duty applies 182 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "vertical motors subject to start-up up-thrust",
      "heavy reversing gearbox shafts",
      "crane travel and slewing drives"
    ],
    "failure_modes": [
      "assembly damage when the central shaft washer is fitted reversed or the two outward-facing housing washers are swapped",
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 80 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "The double-direction 52226 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 110 mm shaft axially in both directions instead of a mirrored pair.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 1,500 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 585 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Ordering discipline for 52226: the catalogue page quotes 52226 and its 182/585 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52226?",
        "a": "The catalogue envelope is 110×190×80 mm, mass 8000 g; ratings C 182 kN / C0 585 kN / Pu 16.6 kN, reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52226 mean?",
        "a": "note the bore of 52226 is 110 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      },
      {
        "q": "Can it replace two single-direction 51-series bearings?",
        "a": "It replaces a mirrored pair functionally — one fit, one housing bore, factory-matched geometry — but its 80 mm height is not twice the single-bearing height and seat details differ, so the housing and cover must be re-drawn rather than swapped in place."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52226",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52226"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52228",
    "brand": "SKF",
    "manufacturer_designation": "52228",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 120,
    "D_mm": 200,
    "B_mm": 81,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 190,
    "static_load_kN": 620,
    "fatigue_load_limit_kN": 17.6,
    "reference_speed_rpm": 1000,
    "limiting_speed_rpm": 1400,
    "max_rpm": 1400,
    "weight_g": 8650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52228 is SKF's 120 mm-bore double-direction thrust ball bearing in the 52200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 120×200×81 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 120 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 120×200×81 mm (4.724×7.874×3.189 in), 40.0 mm radial section, C 190 kN, C0 620 kN, Pu 17.6 kN. reference speed 1,000 r/min (thermal) and limiting speed 1,400 r/min (mechanical), catalogue mass 8650 g. Minimum-load arithmetic: with dm ≈ 160.0 mm and factor A 2, Fam ≈ A·(n·dm/1000)² at the 1,000 r/min reference speed is about 51.2 kN for 52228; below that preload the balls skid and smear the tracks. Selection figures for 52228: the C0/C ratio is 3.26, Pu 17.6 kN is about 9 % of C, and the catalogue mass works out to roughly 72 g per millimetre of bore; the printed minimum-load factor is A 2. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 2 at the 1,400 r/min limiting speed raises the required axial preload to about 100.4 kN; the reference-speed value 51.2 kN is the thermal design point. Stack/annulus proportions: the 81 mm axial stack over the 20,106 mm² washer annulus gives 4.03 mm of height per annular square millimetre ×10⁻³, and at 8650 g the bearing holds about 71.7 kN of C0 per kilogram. Speed-ratio note for this exact unit: the reference speed is 1,000 r/min against a 1,400 r/min limiting speed, a reference-to-limit ratio of 0.71. Double-direction order-number note: the unit is built around one central shaft washer with a ground bore and tracks on both faces, flanked by two housing washers and two independent ball-cage assemblies; observe the assembly orientation (the two housing washers face outwards) and note that a 52-series unit replaces a mirrored pair of 51-series bearings only after the stack height and seat drawings are re-checked. Life accounting for 52228 is done separately per direction: if duty applies 190 kN C predominantly one way, the idle side's skid risk — not the loaded side's L10 — usually sets the relubrication and preload interval.",
    "applications": [
      "heavy converter tilt screws",
      "large marine reversing drives",
      "primary mill adjustment screws under reversing thrust"
    ],
    "failure_modes": [
      "cover-induced thrust preload when the end cover is torqued solid instead of leaving the catalogue axial freedom",
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "unbalanced loading of the two cage sets when one load direction dominates service life and the idle set skids",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 1,400 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 620 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 81 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "Do not replace a 52228 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 120×200 mm bore and OD.",
      "Ordering discipline for 52228: the catalogue page quotes 52228 and its 190/620 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52228?",
        "a": "52228 measures 120 mm bore × 200 mm OD × 81 mm bearing height (4.724 × 7.874 × 3.189 in), mass about 8650 g. SKF 17000 ratings: C 190 kN, C0 620 kN, Pu 17.6 kN, reference speed 1,000 r/min (thermal) and limiting speed 1,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52228 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 120 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "Which fits and retention does 52228 need?",
        "a": "The central shaft washer takes an interference fit on the 120 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      },
      {
        "q": "What static check governs crane-hook duty for 52228?",
        "a": "Hook and screw positions are usually sized on C0 (620 kN here) with the application's static safety factor against peak stationary or shock thrust, not on the 190 kN L10 figure — reversal frequency then decides whether the 52-series geometry is acceptable."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52228",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52228"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52230-M",
    "brand": "SKF",
    "manufacturer_designation": "52230 M",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 130,
    "D_mm": 215,
    "B_mm": 89,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 238,
    "static_load_kN": 800,
    "fatigue_load_limit_kN": 22,
    "reference_speed_rpm": 950,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "weight_g": 11500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52230 M is SKF's 130 mm-bore double-direction thrust ball bearing in the 52200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 130×215×89 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 130 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 130×215×89 mm (5.118×8.465×3.504 in), 42.5 mm radial section, C 238 kN, C0 800 kN, Pu 22 kN. reference speed 950 r/min (thermal) and limiting speed 1,300 r/min (mechanical), catalogue mass 11500 g. Track-circle loading: per millimetre of mean track circumference the 238 kN dynamic rating corresponds to roughly 0.44 kN/mm of π·dm track, a useful comparison against the other dimension series of the 130 mm bore. At the printed limiting speed of 1,300 r/min the mean pitch diameter dm ≈ 172.5 mm implies a dn value around 224k mm·r/min; the 950 r/min reference speed is the thermal-planning value under catalogue load. Imperial cross-check for procurement drawings: 5.118 in bore, 8.465 in OD, 3.504 in height, and the 11500 g catalogue mass converts to 11.500 kg (405.6 oz). Rating split for documentation: dynamic 238 kN (L10 life), static 800 kN (safety factor s0), fatigue limit 22 kN (adjusted life) — three different uses of three different numbers for 52230 M, none interchangeable with another. Speed-ratio note for this exact unit: the reference speed is 950 r/min against a 1,300 r/min limiting speed, a reference-to-limit ratio of 0.73. Heavy double-direction note: the M suffix on a 52/54-series bearing means both ball-cage assemblies are machined brass and ball-centred for the largest bidirectional positions; both cage sets share the same lubrication requirement, so the oil or grease feed must reach the upper as well as the lower track on vertical shafts. The M suffix means BOTH cage sets of the 89 mm stack are machined brass; spare-part orders of one side should still be placed as the complete 52230 M unit, because mixed cage executions in one double-direction stack are not a catalogue configuration.",
    "applications": [
      "large hydraulic-press guidance",
      "large marine reversing drives",
      "offshore winch reversal drums"
    ],
    "failure_modes": [
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "upper brass-cage starvation on a vertical shaft whose lubricant feeds only the lower track pair",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Service both cage sets together: replacing only the noisy side while leaving the worn 800 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 89 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 1,300 r/min even a small thermal thrust preload smears the hottest track.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Ordering discipline for 52230: the catalogue page quotes 52230 M and its 238/800 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52230-M?",
        "a": "52230 M measures 130 mm bore × 215 mm OD × 89 mm bearing height (5.118 × 8.465 × 3.504 in), mass about 11500 g. SKF 17000 ratings: C 238 kN, C0 800 kN, Pu 22 kN, reference speed 950 r/min (thermal) and limiting speed 1,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52230 M mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 130 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is the double-direction 52230 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 130×215×89 mm unit locating the shaft axially in both directions."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52230",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52230-M",
      "52230 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52232-M",
    "brand": "SKF",
    "manufacturer_designation": "52232 M",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 140,
    "D_mm": 225,
    "B_mm": 90,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 238,
    "static_load_kN": 830,
    "fatigue_load_limit_kN": 22.4,
    "reference_speed_rpm": 900,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "weight_g": 12000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52232 M is an ISO 104 double-direction thrust ball bearing, 140 mm bore and 225 mm OD on a flat housing seat, standing 90 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52232 M is 140 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 140×225×90 mm (5.512×8.858×3.543 in), 42.5 mm radial section, C 238 kN, C0 830 kN, Pu 22.4 kN. reference speed 900 r/min (thermal) and limiting speed 1,300 r/min (mechanical), catalogue mass 12000 g. Speed band width for this size is 400 r/min between reference and limiting (1.44× ratio); lubrication, preload and heat removal decide where inside that band 52232 M can actually run. Bore-to-OD planning: OD 225 over bore 140 is a 1.61× step for this size, and the 90 mm height gives a bore/height ratio of 1.56; use these ratios when the housing recess around the 140 mm shaft is the first constraint. Load balance: C0 830 kN against C 238 kN gives a 3.49 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 22.4 kN enters the adjusted-life check. Rating split for documentation: dynamic 238 kN (L10 life), static 830 kN (safety factor s0), fatigue limit 22.4 kN (adjusted life) — three different uses of three different numbers for 52232 M, none interchangeable with another. Stack/annulus proportions: the 90 mm axial stack over the 24,367 mm² washer annulus gives 3.69 mm of height per annular square millimetre ×10⁻³, and at 12000 g the bearing holds about 69.2 kN of C0 per kilogram. Heavy double-direction note: the M suffix on a 52/54-series bearing means both ball-cage assemblies are machined brass and ball-centred for the largest bidirectional positions; both cage sets share the same lubrication requirement, so the oil or grease feed must reach the upper as well as the lower track on vertical shafts. With 12000 g rotating partially with the shaft, check the rotor-balance influence of the central shaft washer at speeds approaching 1,300 r/min; the two loose washers do not rotate and contribute no imbalance.",
    "applications": [
      "large marine reversing drives",
      "primary mill adjustment screws under reversing thrust",
      "offshore winch reversal drums"
    ],
    "failure_modes": [
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "upper brass-cage starvation on a vertical shaft whose lubricant feeds only the lower track pair",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 1,300 r/min even a small thermal thrust preload smears the hottest track.",
      "Service both cage sets together: replacing only the noisy side while leaving the worn 830 kN opposite track in place reproduces the failure within weeks — inspect both shaft-washer faces and both loose washers at removal.",
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Do not replace a 52232 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 140×225 mm bore and OD.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52232 M as the double flat brass execution; other order numbers of the 52232 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52232-M?",
        "a": "The catalogue envelope is 140×225×90 mm, mass 12000 g; ratings C 238 kN / C0 830 kN / Pu 22.4 kN, reference speed 900 r/min (thermal) and limiting speed 1,300 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52232 M mean?",
        "a": "note the bore of 52232 M is 140 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "What minimum axial load applies to a double-direction bearing?",
        "a": "The Fam ≈ A·(n·dm/1000)² rule (factor A 3.8) applies to EACH direction: the momentarily unloaded side during slow reversal is the one that skids, so preload or balanced loading must keep both ball sets seated."
      },
      {
        "q": "How is the double-direction 52232 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 140×225×90 mm unit locating the shaft axially in both directions."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52232",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52232-M",
      "52232 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52234-M",
    "brand": "SKF",
    "manufacturer_designation": "52234 M",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 150,
    "D_mm": 240,
    "B_mm": 97,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 270,
    "static_load_kN": 930,
    "fatigue_load_limit_kN": 24,
    "reference_speed_rpm": 850,
    "limiting_speed_rpm": 1200,
    "max_rpm": 1200,
    "weight_g": 15000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 52234 M is an ISO 104 double-direction thrust ball bearing, 150 mm bore and 240 mm OD on a flat housing seat, standing 97 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 52234 M is 150 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 150×240×97 mm (5.906×9.449×3.819 in), 45.0 mm radial section, C 270 kN, C0 930 kN, Pu 24 kN. reference speed 850 r/min (thermal) and limiting speed 1,200 r/min (mechanical), catalogue mass 15000 g. Speed planning separates the two ceilings mechanically: the pressed brass cage and balls tolerate 1,200 r/min while thermal balance under catalogue load sets the 850 r/min reference; at dm ≈ 195.0 mm the corresponding dn is approximately 234k mm·r/min. Static-first selection data: 930 kN C0 spread across the 97 mm stack gives 9.6 kN of static rating per height millimetre, and the 15000 g mass/C0 ratio is about 16 g per static kN — crane-hook and screw positions are normally sized on these two figures. Light-load floor: Pu = 24 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 52234 M; the number is 9 % of the 270 kN dynamic rating. Load balance: C0 930 kN against C 270 kN gives a 3.44 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 24 kN enters the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 850 r/min against a 1,200 r/min limiting speed, a reference-to-limit ratio of 0.71. Heavy double-direction note: the M suffix on a 52/54-series bearing means both ball-cage assemblies are machined brass and ball-centred for the largest bidirectional positions; both cage sets share the same lubrication requirement, so the oil or grease feed must reach the upper as well as the lower track on vertical shafts. The M suffix means BOTH cage sets of the 97 mm stack are machined brass; spare-part orders of one side should still be placed as the complete 52234 M unit, because mixed cage executions in one double-direction stack are not a catalogue configuration.",
    "applications": [
      "large hydraulic-press guidance",
      "large marine reversing drives",
      "primary mill adjustment screws under reversing thrust"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "upper brass-cage starvation on a vertical shaft whose lubricant feeds only the lower track pair",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Do not replace a 52234 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 150×240 mm bore and OD.",
      "Torque the cover to leave the catalogue axial freedom, never solid: a clamped double-direction stack cannot float to its thermal position, and at 1,200 r/min even a small thermal thrust preload smears the hottest track.",
      "Each direction independently needs the minimum axial load (factor A 5.4): the side that is momentarily unloaded during slow reversal skids first, so arrange preload or symmetry rather than assuming the loaded side drives the idle side.",
      "The central shaft washer takes the interference fit on the 150 mm shaft while both outer housing washers run loose in their registers; both loose washers need positive axial retention on vertical shafts.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 52234 M as the double flat brass execution; other order numbers of the 52234 size are different products and may carry different ratings or seating geometry — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52234-M?",
        "a": "The catalogue envelope is 150×240×97 mm, mass 15000 g; ratings C 270 kN / C0 930 kN / Pu 24 kN, reference speed 850 r/min (thermal) and limiting speed 1,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52234 M mean?",
        "a": "note the bore of 52234 M is 150 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is a vertical double-direction 52234 lubricated and retained?",
        "a": "Use an oil bath reaching the lower track plus a feed or oil level that serves the upper cage set, or a coherent heavy-base grease; positively retain both loose housing washers because gravity loads the upper stack differently at standstill."
      },
      {
        "q": "Which fits and retention does 52234-M need?",
        "a": "The central shaft washer takes an interference fit on the 150 mm shaft; both housing washers run loose in their registers and must be positively retained, especially on vertical shafts, where the upper washer and its cage set also need lubricant retained."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52234",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52234-M",
      "52234 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "52236-M",
    "brand": "SKF",
    "manufacturer_designation": "52236 M",
    "series": "52200-series",
    "type": "thrust_ball",
    "d_mm": 150,
    "D_mm": 250,
    "B_mm": 98,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 302,
    "static_load_kN": 1120,
    "fatigue_load_limit_kN": 28.5,
    "reference_speed_rpm": 800,
    "limiting_speed_rpm": 1100,
    "max_rpm": 1100,
    "weight_g": 16000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "52236 M is SKF's 150 mm-bore double-direction thrust ball bearing in the 52200 series to the ISO 104 dimension plan, with a flat housing seating surface, measuring 150×250×98 mm. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 150 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. Envelope 150×250×98 mm (5.906×9.843×3.858 in), 50.0 mm radial section, C 302 kN, C0 1120 kN, Pu 28.5 kN. reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical), catalogue mass 16000 g. Sizing arithmetic on the 150 mm bore: 302 kN C over the 50.0 mm radial section gives 6.0 kN per section millimetre, and the 98 mm stack height is 1.96× that section — proportions typical of a 52200 thrust section. Section proportions: the 50.0 mm radial section compares with 150 mm of bore (section/bore ≈ 0.33) and the 98 mm height is 1.96× that section — the proportions that identify the 52200 envelope at a glance. Mass and section check: 16000 g inside the 150×250×98 mm outline leaves a 50.0 mm radial section, and the 1120 kN static rating is 3.71× the dynamic rating — plan static safety and minimum preload against those figures. Stack/annulus proportions: the 98 mm axial stack over the 31,416 mm² washer annulus gives 3.12 mm of height per annular square millimetre ×10⁻³, and at 16000 g the bearing holds about 70.0 kN of C0 per kilogram. Envelope economics: the 98 mm axial height over a 50.0 mm radial section yields 3.1 kN of dynamic capacity per height millimetre, and the bearing weighs 16000 g for 302 kN C — about 53 g per rated kN. Heavy double-direction note: the M suffix on a 52/54-series bearing means both ball-cage assemblies are machined brass and ball-centred for the largest bidirectional positions; both cage sets share the same lubrication requirement, so the oil or grease feed must reach the upper as well as the lower track on vertical shafts. With 16000 g rotating partially with the shaft, check the rotor-balance influence of the central shaft washer at speeds approaching 1,100 r/min; the two loose washers do not rotate and contribute no imbalance.",
    "applications": [
      "large hydraulic-press guidance",
      "large marine reversing drives",
      "offshore winch reversal drums"
    ],
    "failure_modes": [
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "upper brass-cage starvation on a vertical shaft whose lubricant feeds only the lower track pair",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Where shaft and housing cannot be kept square, the sphered 54-series execution of the same bore with two U seat washers is the self-aligning counterpart; the flat 52200 unit has no alignment capacity.",
      "Do not replace a 52236 with two single-direction 51-series bearings without re-checking the arrangement: envelope heights, seat details and catalogue ratings differ, even at the same 150×250 mm bore and OD.",
      "Observe the stack order at fitting: shaft washer central, the two housing washers facing outwards with a cage set on each side; the 98 mm total height is not twice a single-direction bearing height, so reuse of old cover dimensions is a trap.",
      "The double-direction 52236 is one central shaft washer with tracks on both faces, two housing washers and two ball-cage assemblies — a single unit locating the 150 mm shaft axially in both directions instead of a mirrored pair.",
      "Ordering discipline for 52236: the catalogue page quotes 52236 M and its 302/1120 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 52236-M?",
        "a": "52236 M measures 150 mm bore × 250 mm OD × 98 mm bearing height (5.906 × 9.843 × 3.858 in), mass about 16000 g. SKF 17000 ratings: C 302 kN, C0 1120 kN, Pu 28.5 kN, reference speed 800 r/min (thermal) and limiting speed 1,100 r/min (mechanical)."
      },
      {
        "q": "What does the designation 52236 M mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 150 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. suffix M identifies a one-piece machined brass cage, ball-centred: the large-size and heavy-section option for higher speeds, shock loads and thin-film lubrication where a pressed cage would distort. 5 = thrust ball bearing, 2 = double direction with flat seating surfaces."
      },
      {
        "q": "How is the double-direction 52236 constructed?",
        "a": "One central shaft washer with tracks on both faces and a ground bore, two housing washers facing outwards and two independent ball-cage assemblies — all supplied as one 150×250×98 mm unit locating the shaft axially in both directions."
      },
      {
        "q": "When should I choose 52-series flat instead of 54-series sphered?",
        "a": "Choose the flat 52-series when the housing register can be machined square to the shaft; choose the 54-series with two U seat washers when initial misalignment has to be accommodated on fabricated or less rigid structures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "52236",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "52236-M",
      "52236 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54306",
    "brand": "SKF",
    "manufacturer_designation": "54306",
    "series": "54300-series",
    "type": "thrust_ball",
    "d_mm": 25,
    "D_mm": 60,
    "B_mm": 41.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 35.8,
    "static_load_kN": 65.5,
    "fatigue_load_limit_kN": 2.4,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 580,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "54306 is SKF's 25 mm-bore double-direction thrust ball bearing in the 54300 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 25×60×41.3 mm U 306 seat washer companion included in the mounted H1 dimension. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 25 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 25×60×41.3 mm (0.984×2.362×1.626 in), 17.5 mm radial section, C 35.8 kN, C0 65.5 kN, Pu 2.4 kN. Mounted height H1 46 mm includes the U 306 seat washer; the bearing alone is 41.3 mm high. reference speed 2,800 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 580 g. Speed band width for this size is 1,000 r/min between reference and limiting (1.36× ratio); lubrication, preload and heat removal decide where inside that band 54306 can actually run. Capacity density: 35.8 kN C from 0.580 kg of bearing steel gives about 61.7 kN per kilogram; static density is correspondingly 112.9 kN/kg at C0 65.5 kN. Imperial cross-check for procurement drawings: 0.984 in bore, 2.362 in OD, 1.626 in height, and the 580 g catalogue mass converts to 0.580 kg (20.5 oz). Stack/annulus proportions: the 41.3 mm axial stack over the 2,337 mm² washer annulus gives 17.67 mm of height per annular square millimetre ×10⁻³, and at 580 g the bearing holds about 112.9 kN of C0 per kilogram. Pitch-diameter arithmetic: dm = (25+60)/2 = 42.5 mm; at the 3,800 r/min limiting speed that corresponds to roughly 162k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. Bill of materials for this page is 54306 plus TWO × U 306; the 46 mm H1 stack sits in a housing whose two register faces should be machined in one clamping to keep both spherical axes coincident.",
    "applications": [
      "medium screw jacks loaded in both directions",
      "agricultural reversing linkage pivots",
      "bidirectional crane-hook and swivel positions with deflecting structure"
    ],
    "failure_modes": [
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "tilted running after a mismatched U washer leaves only a narrow band of spherical contact",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The two spherical interfaces accommodate initial misalignment in either load direction but must stay clean, greased and static — continuous rocking frets the sphered contacts of even the 65.5 kN static-rated set.",
      "Order TWO seat washers for 54306 — the designation U 306 pairs with one side and a second U washer (same number) with the other; the catalogue 46 mm H1 includes both.",
      "Replacement ordering is THREE numbers: 54306 plus two pieces of U 306; quoting only the bearing leaves the sphered backs running on bare registers.",
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "The 35.8/65.5 kN figures belong to 54306 specifically (the double sphered pressed steel execution of 54306); suffixed, sphered and counterpart-series order numbers are separate articles, and U 306 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54306?",
        "a": "54306 measures 25 mm bore × 60 mm OD × 41.3 mm bearing height (0.984 × 2.362 × 1.626 in), or 46 mm mounted H1 including the U 306 seat washer, mass about 580 g. SKF 17000 ratings: C 35.8 kN, C0 65.5 kN, Pu 2.4 kN, reference speed 2,800 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54306 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 25 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "Does the spherical seat work while the shaft rocks continuously?",
        "a": "No — it accommodates initial static misalignment only. Continuous oscillation frets the sphered contacts even with C0 65.5 kN in reserve; keep the interfaces greased and clean and design genuine pivots separately."
      },
      {
        "q": "What loads can 54306 take?",
        "a": "Pure axial load in both directions: C 35.8 kN, C0 65.5 kN, Pu 2.4 kN, with the same minimum-load rule (factor A 0.026) in each direction; radial load is excluded."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54306",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54306",
      "54306 + U 306"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54207",
    "brand": "SKF",
    "manufacturer_designation": "54207",
    "series": "54200-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 37.8,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 35.1,
    "static_load_kN": 73.5,
    "fatigue_load_limit_kN": 2.7,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 530,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "54207 is SKF's 30 mm-bore double-direction thrust ball bearing in the 54200 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 30×62×37.8 mm U 207 seat washer companion included in the mounted H1 dimension. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 30 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 30×62×37.8 mm (1.181×2.441×1.488 in), 16.0 mm radial section, C 35.1 kN, C0 73.5 kN, Pu 2.7 kN. Mounted height H1 42 mm includes the U 207 seat washer; the bearing alone is 37.8 mm high. reference speed 2,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 530 g. Bore-to-OD planning: OD 62 over bore 30 is a 2.07× step for this size, and the 37.8 mm height gives a bore/height ratio of 0.79; use these ratios when the housing recess around the 30 mm shaft is the first constraint. Capacity density: 35.1 kN C from 0.530 kg of bearing steel gives about 66.2 kN per kilogram; static density is correspondingly 138.7 kN/kg at C0 73.5 kN. Load balance: C0 73.5 kN against C 35.1 kN gives a 2.09 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 2.7 kN enters the adjusted-life check. Light-load floor: Pu = 2.7 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 54207; the number is 8 % of the 35.1 kN dynamic rating. Static-first selection data: 73.5 kN C0 spread across the 37.8 mm stack gives 1.9 kN of static rating per height millimetre, and the 530 g mass/C0 ratio is about 7 g per static kN — crane-hook and screw positions are normally sized on these two figures. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. At 30×62×37.8 mm the bearing carries C0 73.5 kN bidirectionally, but the two U interfaces share that load only if each is free to seat; torque the covers so the 4.2 mm-per-side washer steps are not pre-clamped.",
    "applications": [
      "medium screw jacks loaded in both directions",
      "agricultural reversing linkage pivots",
      "bidirectional crane-hook and swivel positions with deflecting structure"
    ],
    "failure_modes": [
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "fretting corrosion in the spherical interface under oscillation with no grease between washer and seat",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "Minimum load factor A 0.028 applies to both load directions, and both brass pressed cage sets need lubricant reaching the upper track on a vertical shaft.",
      "Replacement ordering is THREE numbers: 54207 plus two pieces of U 207; quoting only the bearing leaves the sphered backs running on bare registers.",
      "The 35.1/73.5 kN ratings assume the spherical contacts are free to find their seat — a painted-over or shimmed U washer fixes the angle and turns the self-aligning bearing into an edge-loaded one.",
      "Ordering discipline for 54207: the catalogue page quotes 54207 plus U 207 and its 35.1/73.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54207?",
        "a": "54207 measures 30 mm bore × 62 mm OD × 37.8 mm bearing height (1.181 × 2.441 × 1.488 in), or 42 mm mounted H1 including the U 207 seat washer, mass about 530 g. SKF 17000 ratings: C 35.1 kN, C0 73.5 kN, Pu 2.7 kN, reference speed 2,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54207 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 30 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "Does the spherical seat work while the shaft rocks continuously?",
        "a": "No — it accommodates initial static misalignment only. Continuous oscillation frets the sphered contacts even with C0 73.5 kN in reserve; keep the interfaces greased and clean and design genuine pivots separately."
      },
      {
        "q": "What loads can 54207 take?",
        "a": "Pure axial load in both directions: C 35.1 kN, C0 73.5 kN, Pu 2.7 kN, with the same minimum-load rule (factor A 0.028) in each direction; radial load is excluded."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54207",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54207",
      "54207 + U 207"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54208",
    "brand": "SKF",
    "manufacturer_designation": "54208",
    "series": "54200-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 68,
    "B_mm": 38.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 44.2,
    "static_load_kN": 96.5,
    "fatigue_load_limit_kN": 3.6,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 630,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 54208 is an ISO 104 double-direction thrust ball bearing, 30 mm bore and 68 mm OD, with a sphered housing washer and U seat washer, standing 38.6 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 54208 is 30 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 30×68×38.6 mm (1.181×2.677×1.52 in), 19.0 mm radial section, C 44.2 kN, C0 96.5 kN, Pu 3.6 kN. Mounted height H1 44 mm includes the U 208 seat washer; the bearing alone is 38.6 mm high. reference speed 2,800 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 630 g. At the printed limiting speed of 3,800 r/min the mean pitch diameter dm ≈ 49.0 mm implies a dn value around 186k mm·r/min; the 2,800 r/min reference speed is the thermal-planning value under catalogue load. Imperial cross-check for procurement drawings: 1.181 in bore, 2.677 in OD, 1.52 in height, and the 630 g catalogue mass converts to 0.630 kg (22.2 oz). Track-circle loading: per millimetre of mean track circumference the 44.2 kN dynamic rating corresponds to roughly 0.29 kN/mm of π·dm track, a useful comparison against the other dimension series of the 30 mm bore. Minimum-load arithmetic: with dm ≈ 49.0 mm and factor A 0.058, Fam ≈ A·(n·dm/1000)² at the 2,800 r/min reference speed is about 1.1 kN for 54208; below that preload the balls skid and smear the tracks. Speed planning separates the two ceilings mechanically: the pressed cage and balls tolerate 3,800 r/min while thermal balance under catalogue load sets the 2,800 r/min reference; at dm ≈ 49.0 mm the corresponding dn is approximately 186k mm·r/min. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. Bill of materials for this page is 54208 plus TWO × U 208; the 44 mm H1 stack sits in a housing whose two register faces should be machined in one clamping to keep both spherical axes coincident.",
    "applications": [
      "bidirectional crane-hook and swivel positions with deflecting structure",
      "reversing vertical pumps on fabricated bases",
      "agricultural reversing linkage pivots"
    ],
    "failure_modes": [
      "cover-induced thrust preload when the end cover is torqued solid instead of leaving the catalogue axial freedom",
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "edge loading on the ball set when the U seat washer is fitted with its concave face reversed",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "The 44.2/96.5 kN ratings assume the spherical contacts are free to find their seat — a painted-over or shimmed U washer fixes the angle and turns the self-aligning bearing into an edge-loaded one.",
      "Minimum load factor A 0.058 applies to both load directions, and both brass pressed cage sets need lubricant reaching the upper track on a vertical shaft.",
      "Order TWO seat washers for 54208 — the designation U 208 pairs with one side and a second U washer (same number) with the other; the catalogue 44 mm H1 includes both.",
      "Ordering discipline for 54208: the catalogue page quotes 54208 plus U 208 and its 44.2/96.5 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54208?",
        "a": "The catalogue envelope is 30×68×38.6 mm plus the 5.4 mm the U 208 seat washer adds to reach H1 44 mm, mass 630 g; ratings C 44.2 kN / C0 96.5 kN / Pu 3.6 kN, reference speed 2,800 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54208 mean?",
        "a": "note the bore of 54208 is 30 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "How are the two U washers ordered and fitted?",
        "a": "Order two pieces of U 208 and seat one flat-backed in each housing register with the concave faces towards the sphered housing washers; check both interfaces swivel freely before fitting the central shaft washer, and verify the mounted stack measures the 44 mm H1."
      },
      {
        "q": "How many U seat washers does 54208 need?",
        "a": "Two — one behind each sphered housing washer (the designation U 208 applies to each). The 44 mm H1 installed height includes both, while the bearing itself is 38.6 mm high."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54208",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54208",
      "54208 + U 208"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54307",
    "brand": "SKF",
    "manufacturer_designation": "54307",
    "series": "54300-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 68,
    "B_mm": 47.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 49.4,
    "static_load_kN": 96.5,
    "fatigue_load_limit_kN": 3.55,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "54307 is SKF's 30 mm-bore double-direction thrust ball bearing in the 54300 series to the ISO 104 dimension plan, with a sphered housing washer paired to a U seat washer, measuring 30×68×47.2 mm U 307 seat washer companion included in the mounted H1 dimension. The unit stacks one central shaft washer (ground bore, tight on the shaft), two outward-facing housing washers and two ball-cage assemblies, reacting axial force in both directions. double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 30 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. Envelope 30×68×47.2 mm (1.181×2.677×1.858 in), 19.0 mm radial section, C 49.4 kN, C0 96.5 kN, Pu 3.55 kN. Mounted height H1 52 mm includes the U 307 seat washer; the bearing alone is 47.2 mm high. reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 850 g. Imperial cross-check for procurement drawings: 1.181 in bore, 2.677 in OD, 1.858 in height, and the 850 g catalogue mass converts to 0.850 kg (30.0 oz). Washer-stack proportions: the U 307 seat washer adds 4.8 mm to the 47.2 mm bearing height for a mounted H1 of 52 mm, while the 19.0 mm radial section against 30 mm bore (section/bore ≈ 0.63) identifies the envelope. Bore-to-OD planning: OD 68 over bore 30 is a 2.27× step for this size, and the 47.2 mm height gives a bore/height ratio of 0.64; use these ratios when the housing recess around the 30 mm shaft is the first constraint. Capacity density: 49.4 kN C from 0.850 kg of bearing steel gives about 58.1 kN per kilogram; static density is correspondingly 113.5 kN/kg at C0 96.5 kN. Speed band width for this size is 1,000 r/min between reference and limiting (1.42× ratio); lubrication, preload and heat removal decide where inside that band 54307 can actually run. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. Bill of materials for this page is 54307 plus TWO × U 307; the 52 mm H1 stack sits in a housing whose two register faces should be machined in one clamping to keep both spherical axes coincident.",
    "applications": [
      "medium screw jacks loaded in both directions",
      "bidirectional crane-hook and swivel positions with deflecting structure",
      "machine-tool reversing supports on elastic housings"
    ],
    "failure_modes": [
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "corrosion lock of the spherical pair during long outdoor idleness with no preservative grease",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "Order TWO seat washers for 54307 — the designation U 307 pairs with one side and a second U washer (same number) with the other; the catalogue 52 mm H1 includes both.",
      "The two spherical interfaces accommodate initial misalignment in either load direction but must stay clean, greased and static — continuous rocking frets the sphered contacts of even the 96.5 kN static-rated set.",
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "Minimum load factor A 0.048 applies to both load directions, and both brass pressed cage sets need lubricant reaching the upper track on a vertical shaft.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 54307 as the double sphered pressed steel execution; other order numbers of the 54307 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 307 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54307?",
        "a": "54307 measures 30 mm bore × 68 mm OD × 47.2 mm bearing height (1.181 × 2.677 × 1.858 in), or 52 mm mounted H1 including the U 307 seat washer, mass about 850 g. SKF 17000 ratings: C 49.4 kN, C0 96.5 kN, Pu 3.55 kN, reference speed 2,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54307 mean?",
        "a": "double-direction 52/54 numbering does NOT decode the bore by the usual single-direction ×5 code — read the 30 mm bore from the dimension table; codes recur across the 522/523/524 sections and systematically trail the 51/53 code values. with no cage suffix this is the standard execution with a stamped sheet-steel ball-cage assembly (pressed cage) — the light, quiet and economical cage for small and medium thrust-ball sizes. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "What loads can 54307 take?",
        "a": "Pure axial load in both directions: C 49.4 kN, C0 96.5 kN, Pu 3.55 kN, with the same minimum-load rule (factor A 0.048) in each direction; radial load is excluded."
      },
      {
        "q": "How are the two U washers ordered and fitted?",
        "a": "Order two pieces of U 307 and seat one flat-backed in each housing register with the concave faces towards the sphered housing washers; check both interfaces swivel freely before fitting the central shaft washer, and verify the mounted stack measures the 52 mm H1."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54307",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54307",
      "54307 + U 307"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54308",
    "brand": "SKF",
    "manufacturer_designation": "54308",
    "series": "54300-series",
    "type": "thrust_ball",
    "d_mm": 30,
    "D_mm": 78,
    "B_mm": 54.1,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 61.8,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 1150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 54300 series order number 54308 is a SKF double-direction thrust ball bearing for a 30 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 30×78×54.1 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 30 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 30×78×54.1 mm (1.181×3.071×2.13 in), 24.0 mm radial section, C 61.8 kN, C0 122 kN, Pu 4.5 kN. Mounted height H1 59 mm includes the U 308 seat washer; the bearing alone is 54.1 mm high. reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 1150 g. Speed band width for this size is 800 r/min between reference and limiting (1.36× ratio); lubrication, preload and heat removal decide where inside that band 54308 can actually run. Capacity density: 61.8 kN C from 1.150 kg of bearing steel gives about 53.7 kN per kilogram; static density is correspondingly 106.1 kN/kg at C0 122 kN. At the printed limiting speed of 3,000 r/min the mean pitch diameter dm ≈ 54.0 mm implies a dn value around 162k mm·r/min; the 2,200 r/min reference speed is the thermal-planning value under catalogue load. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.077 at the 3,000 r/min limiting speed raises the required axial preload to about 2.0 kN; the reference-speed value 1.1 kN is the thermal design point. Minimum-load arithmetic: with dm ≈ 54.0 mm and factor A 0.077, Fam ≈ A·(n·dm/1000)² at the 2,200 r/min reference speed is about 1.1 kN for 54308; below that preload the balls skid and smear the tracks. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. Bill of materials for this page is 54308 plus TWO × U 308; the 59 mm H1 stack sits in a housing whose two register faces should be machined in one clamping to keep both spherical axes coincident.",
    "applications": [
      "medium screw jacks loaded in both directions",
      "bidirectional crane-hook and swivel positions with deflecting structure",
      "agricultural reversing linkage pivots"
    ],
    "failure_modes": [
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The 61.8/122 kN ratings assume the spherical contacts are free to find their seat — a painted-over or shimmed U washer fixes the angle and turns the self-aligning bearing into an edge-loaded one.",
      "Replacement ordering is THREE numbers: 54308 plus two pieces of U 308; quoting only the bearing leaves the sphered backs running on bare registers.",
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "Order TWO seat washers for 54308 — the designation U 308 pairs with one side and a second U washer (same number) with the other; the catalogue 59 mm H1 includes both.",
      "Ordering discipline for 54308: the catalogue page quotes 54308 plus U 308 and its 61.8/122 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54308?",
        "a": "Boundary dimensions to ISO 104: bore 30 mm, OD 78 mm, height 54.1 mm (H1 59 mm installed with the U 308 seat washer); weight 1150 g. Load figures from SKF 17000: dynamic 61.8 kN, static 122 kN, fatigue limit 4.5 kN; reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54308 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 30 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "What loads can 54308 take?",
        "a": "Pure axial load in both directions: C 61.8 kN, C0 122 kN, Pu 4.5 kN, with the same minimum-load rule (factor A 0.077) in each direction; radial load is excluded."
      },
      {
        "q": "How are the two U washers ordered and fitted?",
        "a": "Order two pieces of U 308 and seat one flat-backed in each housing register with the concave faces towards the sphered housing washers; check both interfaces swivel freely before fitting the central shaft washer, and verify the mounted stack measures the 59 mm H1."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54308",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54308",
      "54308 + U 308"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54209",
    "brand": "SKF",
    "manufacturer_designation": "54209",
    "series": "54200-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 73,
    "B_mm": 39.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 39,
    "static_load_kN": 86.5,
    "fatigue_load_limit_kN": 3.2,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 780,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 54209 is an ISO 104 double-direction thrust ball bearing, 35 mm bore and 73 mm OD, with a sphered housing washer and U seat washer, standing 39.6 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 54209 is 35 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 35×73×39.6 mm (1.378×2.874×1.559 in), 19.0 mm radial section, C 39 kN, C0 86.5 kN, Pu 3.2 kN. Mounted height H1 45 mm includes the U 209 seat washer; the bearing alone is 39.6 mm high. reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 780 g. Capacity density: 39 kN C from 0.780 kg of bearing steel gives about 50.0 kN per kilogram; static density is correspondingly 110.9 kN/kg at C0 86.5 kN. Mass and section check: 780 g inside the 35×73×39.6 mm outline leaves a 19.0 mm radial section, and the 86.5 kN static rating is 2.22× the dynamic rating — plan static safety and minimum preload against those figures. Track-circle loading: per millimetre of mean track circumference the 39 kN dynamic rating corresponds to roughly 0.23 kN/mm of π·dm track, a useful comparison against the other dimension series of the 35 mm bore. Rating split for documentation: dynamic 39 kN (L10 life), static 86.5 kN (safety factor s0), fatigue limit 3.2 kN (adjusted life) — three different uses of three different numbers for 54209, none interchangeable with another. Minimum-load arithmetic: with dm ≈ 54.0 mm and factor A 0.038, Fam ≈ A·(n·dm/1000)² at the 2,600 r/min reference speed is about 749 N for 54209; below that preload the balls skid and smear the tracks. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. Bill of materials for this page is 54209 plus TWO × U 209; the 45 mm H1 stack sits in a housing whose two register faces should be machined in one clamping to keep both spherical axes coincident.",
    "applications": [
      "reversing vertical pumps on fabricated bases",
      "bidirectional crane-hook and swivel positions with deflecting structure",
      "medium screw jacks loaded in both directions"
    ],
    "failure_modes": [
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The two spherical interfaces accommodate initial misalignment in either load direction but must stay clean, greased and static — continuous rocking frets the sphered contacts of even the 86.5 kN static-rated set.",
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "Order TWO seat washers for 54209 — the designation U 209 pairs with one side and a second U washer (same number) with the other; the catalogue 45 mm H1 includes both.",
      "Minimum load factor A 0.038 applies to both load directions, and both brass pressed cage sets need lubricant reaching the upper track on a vertical shaft.",
      "The 39/86.5 kN figures belong to 54209 specifically (the double sphered pressed steel execution of 54209); suffixed, sphered and counterpart-series order numbers are separate articles, and U 209 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54209?",
        "a": "The catalogue envelope is 35×73×39.6 mm plus the 5.4 mm the U 209 seat washer adds to reach H1 45 mm, mass 780 g; ratings C 39 kN / C0 86.5 kN / Pu 3.2 kN, reference speed 2,600 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54209 mean?",
        "a": "note the bore of 54209 is 35 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "How are the two U washers ordered and fitted?",
        "a": "Order two pieces of U 209 and seat one flat-backed in each housing register with the concave faces towards the sphered housing washers; check both interfaces swivel freely before fitting the central shaft washer, and verify the mounted stack measures the 45 mm H1."
      },
      {
        "q": "How many U seat washers does 54209 need?",
        "a": "Two — one behind each sphered housing washer (the designation U 209 applies to each). The 45 mm H1 installed height includes both, while the bearing itself is 39.6 mm high."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54209",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54209",
      "54209 + U 209"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54309",
    "brand": "SKF",
    "manufacturer_designation": "54309",
    "series": "54300-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 85,
    "B_mm": 56.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 76.1,
    "static_load_kN": 153,
    "fatigue_load_limit_kN": 5.6,
    "reference_speed_rpm": 1900,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 1600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 54309 is an ISO 104 double-direction thrust ball bearing, 35 mm bore and 85 mm OD, with a sphered housing washer and U seat washer, standing 56.2 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 54309 is 35 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 35×85×56.2 mm (1.378×3.346×2.213 in), 25.0 mm radial section, C 76.1 kN, C0 153 kN, Pu 5.6 kN. Mounted height H1 62 mm includes the U 309 seat washer; the bearing alone is 56.2 mm high. reference speed 1,900 r/min (thermal) and limiting speed 2,800 r/min (mechanical), catalogue mass 1600 g. Load balance: C0 153 kN against C 76.1 kN gives a 2.01 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 5.6 kN enters the adjusted-life check. Bore-to-OD planning: OD 85 over bore 35 is a 2.43× step for this size, and the 56.2 mm height gives a bore/height ratio of 0.62; use these ratios when the housing recess around the 35 mm shaft is the first constraint. Mass and section check: 1600 g inside the 35×85×56.2 mm outline leaves a 25.0 mm radial section, and the 153 kN static rating is 2.01× the dynamic rating — plan static safety and minimum preload against those figures. Light-load floor: Pu = 5.6 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 54309; the number is 7 % of the 76.1 kN dynamic rating. Imperial cross-check for procurement drawings: 1.378 in bore, 3.346 in OD, 2.213 in height, and the 1600 g catalogue mass converts to 1.600 kg (56.4 oz). Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. At 35×85×56.2 mm the bearing carries C0 153 kN bidirectionally, but the two U interfaces share that load only if each is free to seat; torque the covers so the 5.8 mm-per-side washer steps are not pre-clamped.",
    "applications": [
      "agricultural reversing linkage pivots",
      "machine-tool reversing supports on elastic housings",
      "medium screw jacks loaded in both directions"
    ],
    "failure_modes": [
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The two spherical interfaces accommodate initial misalignment in either load direction but must stay clean, greased and static — continuous rocking frets the sphered contacts of even the 153 kN static-rated set.",
      "Replacement ordering is THREE numbers: 54309 plus two pieces of U 309; quoting only the bearing leaves the sphered backs running on bare registers.",
      "Minimum load factor A 0.12 applies to both load directions, and both brass pressed cage sets need lubricant reaching the upper track on a vertical shaft.",
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "The 76.1/153 kN figures belong to 54309 specifically (the double sphered pressed steel execution of 54309); suffixed, sphered and counterpart-series order numbers are separate articles, and U 309 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54309?",
        "a": "The catalogue envelope is 35×85×56.2 mm plus the 5.8 mm the U 309 seat washer adds to reach H1 62 mm, mass 1600 g; ratings C 76.1 kN / C0 153 kN / Pu 5.6 kN, reference speed 1,900 r/min (thermal) and limiting speed 2,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54309 mean?",
        "a": "note the bore of 54309 is 35 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "How many U seat washers does 54309 need?",
        "a": "Two — one behind each sphered housing washer (the designation U 309 applies to each). The 62 mm H1 installed height includes both, while the bearing itself is 56.2 mm high."
      },
      {
        "q": "What is the difference between 54309 and two single-direction 53-series bearings?",
        "a": "54309 is one factory-matched bidirectional unit with a central shaft washer; two 53-series bearings would need two shaft seats and roughly twice the axial space with separate fits. The 54-series is the compact reversing counterpart, not a stacking kit."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54309",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54309",
      "54309 + U 309"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54409",
    "brand": "SKF",
    "manufacturer_designation": "54409",
    "series": "54400-series",
    "type": "thrust_ball",
    "d_mm": 35,
    "D_mm": 100,
    "B_mm": 78.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 124,
    "static_load_kN": 240,
    "fatigue_load_limit_kN": 9,
    "reference_speed_rpm": 1500,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "weight_g": 3000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 54409 is an ISO 104 double-direction thrust ball bearing, 35 mm bore and 100 mm OD, with a sphered housing washer and U seat washer, standing 78.9 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 54409 is 35 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 35×100×78.9 mm (1.378×3.937×3.106 in), 32.5 mm radial section, C 124 kN, C0 240 kN, Pu 9 kN. Mounted height H1 86 mm includes the U 409 seat washer; the bearing alone is 78.9 mm high. reference speed 1,500 r/min (thermal) and limiting speed 2,000 r/min (mechanical), catalogue mass 3000 g. At the printed limiting speed of 2,000 r/min the mean pitch diameter dm ≈ 67.5 mm implies a dn value around 135k mm·r/min; the 1,500 r/min reference speed is the thermal-planning value under catalogue load. Pitch-diameter arithmetic: dm = (35+100)/2 = 67.5 mm; at the 2,000 r/min limiting speed that corresponds to roughly 135k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.37 at the 2,000 r/min limiting speed raises the required axial preload to about 6.7 kN; the reference-speed value 3.8 kN is the thermal design point. Mass and section check: 3000 g inside the 35×100×78.9 mm outline leaves a 32.5 mm radial section, and the 240 kN static rating is 1.94× the dynamic rating — plan static safety and minimum preload against those figures. Bore-to-OD planning: OD 100 over bore 35 is a 2.86× step for this size, and the 78.9 mm height gives a bore/height ratio of 0.44; use these ratios when the housing recess around the 35 mm shaft is the first constraint. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. At 35×100×78.9 mm the bearing carries C0 240 kN bidirectionally, but the two U interfaces share that load only if each is free to seat; torque the covers so the 7.1 mm-per-side washer steps are not pre-clamped.",
    "applications": [
      "reversing vertical pumps on fabricated bases",
      "agricultural reversing linkage pivots",
      "medium screw jacks loaded in both directions"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "fretting corrosion in the spherical interface under oscillation with no grease between washer and seat",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "Order TWO seat washers for 54409 — the designation U 409 pairs with one side and a second U washer (same number) with the other; the catalogue 86 mm H1 includes both.",
      "Minimum load factor A 0.37 applies to both load directions, and both brass pressed cage sets need lubricant reaching the upper track on a vertical shaft.",
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "The two spherical interfaces accommodate initial misalignment in either load direction but must stay clean, greased and static — continuous rocking frets the sphered contacts of even the 240 kN static-rated set.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 54409 as the double sphered pressed steel execution; other order numbers of the 54409 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 409 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54409?",
        "a": "The catalogue envelope is 35×100×78.9 mm plus the 7.1 mm the U 409 seat washer adds to reach H1 86 mm, mass 3000 g; ratings C 124 kN / C0 240 kN / Pu 9 kN, reference speed 1,500 r/min (thermal) and limiting speed 2,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54409 mean?",
        "a": "note the bore of 54409 is 35 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "Does the spherical seat work while the shaft rocks continuously?",
        "a": "No — it accommodates initial static misalignment only. Continuous oscillation frets the sphered contacts even with C0 240 kN in reserve; keep the interfaces greased and clean and design genuine pivots separately."
      },
      {
        "q": "What loads can 54409 take?",
        "a": "Pure axial load in both directions: C 124 kN, C0 240 kN, Pu 9 kN, with the same minimum-load rule (factor A 0.37) in each direction; radial load is excluded."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54409",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54409",
      "54409 + U 409"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54310",
    "brand": "SKF",
    "manufacturer_designation": "54310",
    "series": "54300-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 95,
    "B_mm": 64.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 81.9,
    "static_load_kN": 170,
    "fatigue_load_limit_kN": 6.3,
    "reference_speed_rpm": 1700,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 2300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 54310 is an ISO 104 double-direction thrust ball bearing, 40 mm bore and 95 mm OD, with a sphered housing washer and U seat washer, standing 64.7 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 54310 is 40 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 40×95×64.7 mm (1.575×3.74×2.547 in), 27.5 mm radial section, C 81.9 kN, C0 170 kN, Pu 6.3 kN. Mounted height H1 70 mm includes the U 310 seat washer; the bearing alone is 64.7 mm high. reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 2300 g. Light-load floor: Pu = 6.3 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 54310; the number is 8 % of the 81.9 kN dynamic rating. At the printed limiting speed of 2,400 r/min the mean pitch diameter dm ≈ 67.5 mm implies a dn value around 162k mm·r/min; the 1,700 r/min reference speed is the thermal-planning value under catalogue load. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.19 at the 2,400 r/min limiting speed raises the required axial preload to about 5.0 kN; the reference-speed value 2.5 kN is the thermal design point. Pitch-diameter arithmetic: dm = (40+95)/2 = 67.5 mm; at the 2,400 r/min limiting speed that corresponds to roughly 162k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Static-first selection data: 170 kN C0 spread across the 64.7 mm stack gives 2.6 kN of static rating per height millimetre, and the 2300 g mass/C0 ratio is about 14 g per static kN — crane-hook and screw positions are normally sized on these two figures. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. At 40×95×64.7 mm the bearing carries C0 170 kN bidirectionally, but the two U interfaces share that load only if each is free to seat; torque the covers so the 5.3 mm-per-side washer steps are not pre-clamped.",
    "applications": [
      "reversing vertical pumps on fabricated bases",
      "medium screw jacks loaded in both directions",
      "bidirectional crane-hook and swivel positions with deflecting structure"
    ],
    "failure_modes": [
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit"
    ],
    "pitfalls": [
      "The 81.9/170 kN ratings assume the spherical contacts are free to find their seat — a painted-over or shimmed U washer fixes the angle and turns the self-aligning bearing into an edge-loaded one.",
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "Minimum load factor A 0.19 applies to both load directions, and both brass pressed cage sets need lubricant reaching the upper track on a vertical shaft.",
      "Order TWO seat washers for 54310 — the designation U 310 pairs with one side and a second U washer (same number) with the other; the catalogue 70 mm H1 includes both.",
      "Ordering discipline for 54310: the catalogue page quotes 54310 plus U 310 and its 81.9/170 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54310?",
        "a": "The catalogue envelope is 40×95×64.7 mm plus the 5.3 mm the U 310 seat washer adds to reach H1 70 mm, mass 2300 g; ratings C 81.9 kN / C0 170 kN / Pu 6.3 kN, reference speed 1,700 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54310 mean?",
        "a": "note the bore of 54310 is 40 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "What is the difference between 54310 and two single-direction 53-series bearings?",
        "a": "54310 is one factory-matched bidirectional unit with a central shaft washer; two 53-series bearings would need two shaft seats and roughly twice the axial space with separate fits. The 54-series is the compact reversing counterpart, not a stacking kit."
      },
      {
        "q": "Does the spherical seat work while the shaft rocks continuously?",
        "a": "No — it accommodates initial static misalignment only. Continuous oscillation frets the sphered contacts even with C0 170 kN in reserve; keep the interfaces greased and clean and design genuine pivots separately."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54310",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54310",
      "54310 + U 310"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54410",
    "brand": "SKF",
    "manufacturer_designation": "54410",
    "series": "54400-series",
    "type": "thrust_ball",
    "d_mm": 40,
    "D_mm": 110,
    "B_mm": 83.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 148,
    "static_load_kN": 305,
    "fatigue_load_limit_kN": 11.4,
    "reference_speed_rpm": 1400,
    "limiting_speed_rpm": 1900,
    "max_rpm": 1900,
    "weight_g": 4450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 54400 series order number 54410 is a SKF double-direction thrust ball bearing for a 40 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 40×110×83.2 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 40 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 40×110×83.2 mm (1.575×4.331×3.276 in), 35.0 mm radial section, C 148 kN, C0 305 kN, Pu 11.4 kN. Mounted height H1 92 mm includes the U 410 seat washer; the bearing alone is 83.2 mm high. reference speed 1,400 r/min (thermal) and limiting speed 1,900 r/min (mechanical), catalogue mass 4450 g. Speed-ratio note for this exact unit: the reference speed is 1,400 r/min against a 1,900 r/min limiting speed, a reference-to-limit ratio of 0.74. Minimum-load arithmetic: with dm ≈ 75.0 mm and factor A 0.6, Fam ≈ A·(n·dm/1000)² at the 1,400 r/min reference speed is about 6.6 kN for 54410; below that preload the balls skid and smear the tracks. Mass and section check: 4450 g inside the 40×110×83.2 mm outline leaves a 35.0 mm radial section, and the 305 kN static rating is 2.06× the dynamic rating — plan static safety and minimum preload against those figures. Rating split for documentation: dynamic 148 kN (L10 life), static 305 kN (safety factor s0), fatigue limit 11.4 kN (adjusted life) — three different uses of three different numbers for 54410, none interchangeable with another. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.6 at the 1,900 r/min limiting speed raises the required axial preload to about 12.2 kN; the reference-speed value 6.6 kN is the thermal design point. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. At 40×110×83.2 mm the bearing carries C0 305 kN bidirectionally, but the two U interfaces share that load only if each is free to seat; torque the covers so the 8.8 mm-per-side washer steps are not pre-clamped.",
    "applications": [
      "agricultural reversing linkage pivots",
      "reversing vertical pumps on fabricated bases",
      "medium screw jacks loaded in both directions"
    ],
    "failure_modes": [
      "track-edge spalling after the shaft washer seat is machined out of square and both rows share the tilt",
      "assembly damage when the central shaft washer is fitted reversed or the two outward-facing housing washers are swapped",
      "edge loading on the ball set when the U seat washer is fitted with its concave face reversed",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "washer face scoring from swarf trapped between the loose housing washer and its register",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer"
    ],
    "pitfalls": [
      "Order TWO seat washers for 54410 — the designation U 410 pairs with one side and a second U washer (same number) with the other; the catalogue 92 mm H1 includes both.",
      "The 148/305 kN ratings assume the spherical contacts are free to find their seat — a painted-over or shimmed U washer fixes the angle and turns the self-aligning bearing into an edge-loaded one.",
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "Replacement ordering is THREE numbers: 54410 plus two pieces of U 410; quoting only the bearing leaves the sphered backs running on bare registers.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 54410 as the double sphered pressed steel execution; other order numbers of the 54410 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 410 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54410?",
        "a": "Boundary dimensions to ISO 104: bore 40 mm, OD 110 mm, height 83.2 mm (H1 92 mm installed with the U 410 seat washer); weight 4450 g. Load figures from SKF 17000: dynamic 148 kN, static 305 kN, fatigue limit 11.4 kN; reference speed 1,400 r/min (thermal) and limiting speed 1,900 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54410 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 40 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "Does the spherical seat work while the shaft rocks continuously?",
        "a": "No — it accommodates initial static misalignment only. Continuous oscillation frets the sphered contacts even with C0 305 kN in reserve; keep the interfaces greased and clean and design genuine pivots separately."
      },
      {
        "q": "What loads can 54410 take?",
        "a": "Pure axial load in both directions: C 148 kN, C0 305 kN, Pu 11.4 kN, with the same minimum-load rule (factor A 0.6) in each direction; radial load is excluded."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54410",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54410",
      "54410 + U 410"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54211",
    "brand": "SKF",
    "manufacturer_designation": "54211",
    "series": "54200-series",
    "type": "thrust_ball",
    "d_mm": 45,
    "D_mm": 90,
    "B_mm": 49.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 58.5,
    "static_load_kN": 134,
    "fatigue_load_limit_kN": 4.9,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 1300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 54211 is an ISO 104 double-direction thrust ball bearing, 45 mm bore and 90 mm OD, with a sphered housing washer and U seat washer, standing 49.6 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 54211 is 45 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 45×90×49.6 mm (1.772×3.543×1.953 in), 22.5 mm radial section, C 58.5 kN, C0 134 kN, Pu 4.9 kN. Mounted height H1 55 mm includes the U 211 seat washer; the bearing alone is 49.6 mm high. reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 1300 g. Imperial cross-check for procurement drawings: 1.772 in bore, 3.543 in OD, 1.953 in height, and the 1300 g catalogue mass converts to 1.300 kg (45.9 oz). Washer-stack proportions: the U 211 seat washer adds 5.4 mm to the 49.6 mm bearing height for a mounted H1 of 55 mm, while the 22.5 mm radial section against 45 mm bore (section/bore ≈ 0.50) identifies the envelope. Pitch-diameter arithmetic: dm = (45+90)/2 = 67.5 mm; at the 3,000 r/min limiting speed that corresponds to roughly 203k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Rating split for documentation: dynamic 58.5 kN (L10 life), static 134 kN (safety factor s0), fatigue limit 4.9 kN (adjusted life) — three different uses of three different numbers for 54211, none interchangeable with another. Selection figures for 54211: the C0/C ratio is 2.29, Pu 4.9 kN is about 8 % of C, and the catalogue mass works out to roughly 29 g per millimetre of bore; the printed minimum-load factor is A 0.11. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. Bill of materials for this page is 54211 plus TWO × U 211; the 55 mm H1 stack sits in a housing whose two register faces should be machined in one clamping to keep both spherical axes coincident.",
    "applications": [
      "machine-tool reversing supports on elastic housings",
      "agricultural reversing linkage pivots",
      "reversing vertical pumps on fabricated bases"
    ],
    "failure_modes": [
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "cage-set loss during handling because the five components separate as soon as the unit leaves the recess",
      "corrosion lock of the spherical pair during long outdoor idleness with no preservative grease",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "fretting corrosion on the shaft-washer ground bore after a loose rotating fit",
      "overheating from grease overfill churning inside a sealed housing recess with no escape volume"
    ],
    "pitfalls": [
      "Order TWO seat washers for 54211 — the designation U 211 pairs with one side and a second U washer (same number) with the other; the catalogue 55 mm H1 includes both.",
      "The two spherical interfaces accommodate initial misalignment in either load direction but must stay clean, greased and static — continuous rocking frets the sphered contacts of even the 134 kN static-rated set.",
      "Minimum load factor A 0.11 applies to both load directions, and both brass pressed cage sets need lubricant reaching the upper track on a vertical shaft.",
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 54211 as the double sphered pressed steel execution; other order numbers of the 54211 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 211 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54211?",
        "a": "The catalogue envelope is 45×90×49.6 mm plus the 5.4 mm the U 211 seat washer adds to reach H1 55 mm, mass 1300 g; ratings C 58.5 kN / C0 134 kN / Pu 4.9 kN, reference speed 2,200 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54211 mean?",
        "a": "note the bore of 54211 is 45 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "Does the spherical seat work while the shaft rocks continuously?",
        "a": "No — it accommodates initial static misalignment only. Continuous oscillation frets the sphered contacts even with C0 134 kN in reserve; keep the interfaces greased and clean and design genuine pivots separately."
      },
      {
        "q": "What loads can 54211 take?",
        "a": "Pure axial load in both directions: C 58.5 kN, C0 134 kN, Pu 4.9 kN, with the same minimum-load rule (factor A 0.11) in each direction; radial load is excluded."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54211",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54211",
      "54211 + U 211"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54312",
    "brand": "SKF",
    "manufacturer_designation": "54312",
    "series": "54300-series",
    "type": "thrust_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 70.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 101,
    "static_load_kN": 224,
    "fatigue_load_limit_kN": 8.3,
    "reference_speed_rpm": 1500,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 2900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 54312 is an ISO 104 double-direction thrust ball bearing, 50 mm bore and 110 mm OD, with a sphered housing washer and U seat washer, standing 70.7 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 54312 is 50 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. Envelope 50×110×70.7 mm (1.969×4.331×2.783 in), 30.0 mm radial section, C 101 kN, C0 224 kN, Pu 8.3 kN. Mounted height H1 78 mm includes the U 312 seat washer; the bearing alone is 70.7 mm high. reference speed 1,500 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 2900 g. Speed band width for this size is 700 r/min between reference and limiting (1.47× ratio); lubrication, preload and heat removal decide where inside that band 54312 can actually run. Speed-ratio note for this exact unit: the reference speed is 1,500 r/min against a 2,200 r/min limiting speed, a reference-to-limit ratio of 0.68. Load balance: C0 224 kN against C 101 kN gives a 2.22 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 8.3 kN enters the adjusted-life check. Light-load floor: Pu = 8.3 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 54312; the number is 8 % of the 101 kN dynamic rating. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.26 at the 2,200 r/min limiting speed raises the required axial preload to about 8.1 kN; the reference-speed value 3.7 kN is the thermal design point. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. At 50×110×70.7 mm the bearing carries C0 224 kN bidirectionally, but the two U interfaces share that load only if each is free to seat; torque the covers so the 7.3 mm-per-side washer steps are not pre-clamped.",
    "applications": [
      "bidirectional crane-hook and swivel positions with deflecting structure",
      "reversing vertical pumps on fabricated bases",
      "machine-tool reversing supports on elastic housings"
    ],
    "failure_modes": [
      "differential wear when one cage set loses lubrication first on a vertical mounting",
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "tilted running after a mismatched U washer leaves only a narrow band of spherical contact",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "grease starvation on a vertical shaft as lubricant drains away from the upper washer",
      "electrical discharge pitting when the shaft current passes through the ball contacts instead of a grounding brush"
    ],
    "pitfalls": [
      "The two spherical interfaces accommodate initial misalignment in either load direction but must stay clean, greased and static — continuous rocking frets the sphered contacts of even the 224 kN static-rated set.",
      "Order TWO seat washers for 54312 — the designation U 312 pairs with one side and a second U washer (same number) with the other; the catalogue 78 mm H1 includes both.",
      "Minimum load factor A 0.26 applies to both load directions, and both brass pressed cage sets need lubricant reaching the upper track on a vertical shaft.",
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "The 101/224 kN figures belong to 54312 specifically (the double sphered pressed steel execution of 54312); suffixed, sphered and counterpart-series order numbers are separate articles, and U 312 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54312?",
        "a": "The catalogue envelope is 50×110×70.7 mm plus the 7.3 mm the U 312 seat washer adds to reach H1 78 mm, mass 2900 g; ratings C 101 kN / C0 224 kN / Pu 8.3 kN, reference speed 1,500 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54312 mean?",
        "a": "note the bore of 54312 is 50 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. no cage suffix means the standard stamped steel retainer — a pressed sheet-metal ball-cage assembly that covers the bulk of the thrust-ball assortment. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "How are the two U washers ordered and fitted?",
        "a": "Order two pieces of U 312 and seat one flat-backed in each housing register with the concave faces towards the sphered housing washers; check both interfaces swivel freely before fitting the central shaft washer, and verify the mounted stack measures the 78 mm H1."
      },
      {
        "q": "How many U seat washers does 54312 need?",
        "a": "Two — one behind each sphered housing washer (the designation U 312 applies to each). The 78 mm H1 installed height includes both, while the bearing itself is 70.7 mm high."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54312",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54312",
      "54312 + U 312"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54316",
    "brand": "SKF",
    "manufacturer_designation": "54316",
    "series": "54300-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 86.1,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 159,
    "static_load_kN": 390,
    "fatigue_load_limit_kN": 13.7,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "weight_g": 5550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 54300 series order number 54316 is a SKF double-direction thrust ball bearing for a 65 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 65×140×86.1 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 65 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 65×140×86.1 mm (2.559×5.512×3.39 in), 37.5 mm radial section, C 159 kN, C0 390 kN, Pu 13.7 kN. Mounted height H1 95 mm includes the U 316 seat washer; the bearing alone is 86.1 mm high. reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical), catalogue mass 5550 g. Track-circle loading: per millimetre of mean track circumference the 159 kN dynamic rating corresponds to roughly 0.49 kN/mm of π·dm track, a useful comparison against the other dimension series of the 65 mm bore. Speed-ratio note for this exact unit: the reference speed is 1,300 r/min against a 1,800 r/min limiting speed, a reference-to-limit ratio of 0.72. Static-first selection data: 390 kN C0 spread across the 86.1 mm stack gives 4.5 kN of static rating per height millimetre, and the 5550 g mass/C0 ratio is about 14 g per static kN — crane-hook and screw positions are normally sized on these two figures. Rating split for documentation: dynamic 159 kN (L10 life), static 390 kN (safety factor s0), fatigue limit 13.7 kN (adjusted life) — three different uses of three different numbers for 54316, none interchangeable with another. Preload at the mechanical ceiling: repeating Fam ≈ A·(n·dm/1000)² with factor A 0.79 at the 1,800 r/min limiting speed raises the required axial preload to about 26.9 kN; the reference-speed value 14.0 kN is the thermal design point. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. Bill of materials for this page is 54316 plus TWO × U 316; the 95 mm H1 stack sits in a housing whose two register faces should be machined in one clamping to keep both spherical axes coincident.",
    "applications": [
      "large two-direction screwdown screws",
      "winch drives with bidirectional thrust on welded frames",
      "heavy turret and slewing adjustments"
    ],
    "failure_modes": [
      "cover-induced thrust preload when the end cover is torqued solid instead of leaving the catalogue axial freedom",
      "assembly damage when the central shaft washer is fitted reversed or the two outward-facing housing washers are swapped",
      "fretting corrosion in the spherical interface under oscillation with no grease between washer and seat",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "washer face scoring from swarf trapped between the loose housing washer and its register"
    ],
    "pitfalls": [
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "Minimum load factor A 0.79 applies to both load directions, and both brass pressed cage sets need lubricant reaching the upper track on a vertical shaft.",
      "The 159/390 kN ratings assume the spherical contacts are free to find their seat — a painted-over or shimmed U washer fixes the angle and turns the self-aligning bearing into an edge-loaded one.",
      "Replacement ordering is THREE numbers: 54316 plus two pieces of U 316; quoting only the bearing leaves the sphered backs running on bare registers.",
      "Ordering discipline for 54316: the catalogue page quotes 54316 plus U 316 and its 159/390 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54316?",
        "a": "Boundary dimensions to ISO 104: bore 65 mm, OD 140 mm, height 86.1 mm (H1 95 mm installed with the U 316 seat washer); weight 5550 g. Load figures from SKF 17000: dynamic 159 kN, static 390 kN, fatigue limit 13.7 kN; reference speed 1,300 r/min (thermal) and limiting speed 1,800 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54316 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 65 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "How many U seat washers does 54316 need?",
        "a": "Two — one behind each sphered housing washer (the designation U 316 applies to each). The 95 mm H1 installed height includes both, while the bearing itself is 86.1 mm high."
      },
      {
        "q": "What is the difference between 54316 and two single-direction 53-series bearings?",
        "a": "54316 is one factory-matched bidirectional unit with a central shaft washer; two 53-series bearings would need two shaft seats and roughly twice the axial space with separate fits. The 54-series is the compact reversing counterpart, not a stacking kit."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54316",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54316",
      "54316 + U 316"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54416-M",
    "brand": "SKF",
    "manufacturer_designation": "54416 M",
    "series": "54400-series",
    "type": "thrust_ball",
    "d_mm": 65,
    "D_mm": 170,
    "B_mm": 128.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 307,
    "static_load_kN": 750,
    "fatigue_load_limit_kN": 25,
    "reference_speed_rpm": 850,
    "limiting_speed_rpm": 1200,
    "max_rpm": 1200,
    "weight_g": 17500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 54400 series order number 54416 M is a SKF double-direction thrust ball bearing for a 65 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 65×170×128.5 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 65 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. Envelope 65×170×128.5 mm (2.559×6.693×5.059 in), 52.5 mm radial section, C 307 kN, C0 750 kN, Pu 25 kN. Mounted height H1 140 mm includes the U 416 seat washer; the bearing alone is 128.5 mm high. reference speed 850 r/min (thermal) and limiting speed 1,200 r/min (mechanical), catalogue mass 17500 g. Sizing arithmetic on the 65 mm bore: 307 kN C over the 52.5 mm radial section gives 5.8 kN per section millimetre, and the 128.5 mm stack height is 2.45× that section — proportions typical of a 54400 thrust section. Speed-ratio note for this exact unit: the reference speed is 850 r/min against a 1,200 r/min limiting speed, a reference-to-limit ratio of 0.71. Capacity density: 307 kN C from 17.500 kg of bearing steel gives about 17.5 kN per kilogram; static density is correspondingly 42.9 kN/kg at C0 750 kN. Speed planning separates the two ceilings mechanically: the pressed brass cage and balls tolerate 1,200 r/min while thermal balance under catalogue load sets the 850 r/min reference; at dm ≈ 117.5 mm the corresponding dn is approximately 141k mm·r/min. Track-circle loading: per millimetre of mean track circumference the 307 kN dynamic rating corresponds to roughly 0.83 kN/mm of π·dm track, a useful comparison against the other dimension series of the 65 mm bore. Heavy bidirectional self-aligning note: the two machined brass cage sets and the two sphered housing washer / U seat-washer pairs make this the heaviest standard thrust-ball execution of its bore — check both spherical interfaces for fretting at overhaul and confirm both U washers are the catalogue-matched designations before reassembly. Condition monitoring of 54416 M should sample both sides independently: asymmetric wear between the two 750 kN-rated track pairs reveals unequal duty or one spherical interface that has stopped seating.",
    "applications": [
      "large vertical-pump thrust with up-thrust events",
      "winch drives with bidirectional thrust on welded frames",
      "large two-direction screwdown screws"
    ],
    "failure_modes": [
      "brinelling of one track pair from a static reversing shock concentrated on a single side",
      "cover-induced thrust preload when the end cover is torqued solid instead of leaving the catalogue axial freedom",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "asymmetric cage wear when reversing duty loads one brass cage set far more often than the other",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "Minimum load factor A 2.3 applies to both load directions, and both brass machined cage sets need lubricant reaching the upper track on a vertical shaft.",
      "Replacement ordering is THREE numbers: 54416 M plus two pieces of U 416; quoting only the bearing leaves the sphered backs running on bare registers.",
      "The 307/750 kN ratings assume the spherical contacts are free to find their seat — a painted-over or shimmed U washer fixes the angle and turns the self-aligning bearing into an edge-loaded one.",
      "Order TWO seat washers for 54416 M — the designation U 416 pairs with one side and a second U washer (same number) with the other; the catalogue 140 mm H1 includes both.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 54416 M as the double sphered brass execution; other order numbers of the 54416 size are different products and may carry different ratings or seating geometry — always quote the full designation including the U 416 seat washer when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54416-M?",
        "a": "Boundary dimensions to ISO 104: bore 65 mm, OD 170 mm, height 128.5 mm (H1 140 mm installed with the U 416 seat washer); weight 17500 g. Load figures from SKF 17000: dynamic 307 kN, static 750 kN, fatigue limit 25 kN; reference speed 850 r/min (thermal) and limiting speed 1,200 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54416 M mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 65 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the trailing M names a solid machined brass window cage centred on the balls rather than on a washer, the catalogue choice when size, speed or interrupted lubrication rules out sheet steel. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "How many U seat washers does 54416-M need?",
        "a": "Two — one behind each sphered housing washer (the designation U 416 applies to each). The 140 mm H1 installed height includes both, while the bearing itself is 128.5 mm high."
      },
      {
        "q": "What is the difference between 54416 and two single-direction 53-series bearings?",
        "a": "54416 M is one factory-matched bidirectional unit with a central shaft washer; two 53-series bearings would need two shaft seats and roughly twice the axial space with separate fits. The 54-series is the compact reversing counterpart, not a stacking kit."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54416",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54416-M",
      "54416 M",
      "54416 M + U 416"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54317",
    "brand": "SKF",
    "manufacturer_designation": "54317",
    "series": "54300-series",
    "type": "thrust_ball",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 95.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 174,
    "static_load_kN": 405,
    "fatigue_load_limit_kN": 14,
    "reference_speed_rpm": 1100,
    "limiting_speed_rpm": 1500,
    "max_rpm": 1500,
    "weight_g": 7950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "The 54300 series order number 54317 is a SKF double-direction thrust ball bearing for a 70 mm seat, built to ISO 104, with a sphered housing washer paired to a U seat washer, 70×150×95.2 mm boundary dimensions. Inside the unit sit a single central shaft washer with a ground interference bore, two outward-facing loose housing washers and two independent ball-cage assemblies, so axial force is reacted in both directions from one housing recess. bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 70 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. Envelope 70×150×95.2 mm (2.756×5.906×3.748 in), 40.0 mm radial section, C 174 kN, C0 405 kN, Pu 14 kN. Mounted height H1 105 mm includes the U 317 seat washer; the bearing alone is 95.2 mm high. reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical), catalogue mass 7950 g. Sizing arithmetic on the 70 mm bore: 174 kN C over the 40.0 mm radial section gives 4.3 kN per section millimetre, and the 95.2 mm stack height is 2.38× that section — proportions typical of a 54300 thrust section. Light-load floor: Pu = 14 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 54317; the number is 8 % of the 174 kN dynamic rating. Static-first selection data: 405 kN C0 spread across the 95.2 mm stack gives 4.3 kN of static rating per height millimetre, and the 7950 g mass/C0 ratio is about 20 g per static kN — crane-hook and screw positions are normally sized on these two figures. Pitch-diameter arithmetic: dm = (70+150)/2 = 110.0 mm; at the 1,500 r/min limiting speed that corresponds to roughly 165k mm·r/min, the figure used when comparing cage speed demand across the thrust-ball series. Load balance: C0 405 kN against C 174 kN gives a 2.33 ratio — thrust ball bearings are chosen on static rating and F_a/C0 far more often than on L10 life, while Pu 14 kN enters the adjusted-life check. Bidirectional self-aligning note: TWO U seat washers are required for this order number, one behind each housing washer, and the catalogue H1 height includes them on both sides of the stack; the spherical interfaces accept initial misalignment in either load direction but are not pivots for continuous oscillation. Bill of materials for this page is 54317 plus TWO × U 317; the 105 mm H1 stack sits in a housing whose two register faces should be machined in one clamping to keep both spherical axes coincident.",
    "applications": [
      "large vertical-pump thrust with up-thrust events",
      "heavy turret and slewing adjustments",
      "large two-direction screwdown screws"
    ],
    "failure_modes": [
      "ball skidding on the momentarily unloaded side during rapid thrust reversal below the minimum load",
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "total loss of the aligning function after paint, scale or abrasive dust fills the sphered contact",
      "one-side spherical seizure after grit fills the interface of the U washer on the less-loaded side",
      "raceway indentation from driving the bearing home through the ball set rather than the washer face",
      "abrasive scoring of washers and balls when the open arrangement runs without external sealing"
    ],
    "pitfalls": [
      "The two spherical interfaces accommodate initial misalignment in either load direction but must stay clean, greased and static — continuous rocking frets the sphered contacts of even the 405 kN static-rated set.",
      "Replacement ordering is THREE numbers: 54317 plus two pieces of U 317; quoting only the bearing leaves the sphered backs running on bare registers.",
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "Minimum load factor A 1.1 applies to both load directions, and both brass pressed cage sets need lubricant reaching the upper track on a vertical shaft.",
      "The 174/405 kN figures belong to 54317 specifically (the double sphered pressed steel execution of 54317); suffixed, sphered and counterpart-series order numbers are separate articles, and U 317 is ordered separately, so write the complete designation on the order and the maintenance record."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54317?",
        "a": "Boundary dimensions to ISO 104: bore 70 mm, OD 150 mm, height 95.2 mm (H1 105 mm installed with the U 317 seat washer); weight 7950 g. Load figures from SKF 17000: dynamic 174 kN, static 405 kN, fatigue limit 14 kN; reference speed 1,100 r/min (thermal) and limiting speed 1,500 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54317 mean?",
        "a": "bore-coding caveat: on 52/54 double-direction bearings the last two digits are an order-number code, not ×5 millimetres — this size carries a 70 mm bore per the ISO 104 table, and guessing from the code gives the wrong shaft. the suffix-free listing carries the catalogue default: a pressed (stamped sheet-steel) ball-cage assembly, light and quiet, used across the small and medium sizes. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "What is the difference between 54317 and two single-direction 53-series bearings?",
        "a": "54317 is one factory-matched bidirectional unit with a central shaft washer; two 53-series bearings would need two shaft seats and roughly twice the axial space with separate fits. The 54-series is the compact reversing counterpart, not a stacking kit."
      },
      {
        "q": "Does the spherical seat work while the shaft rocks continuously?",
        "a": "No — it accommodates initial static misalignment only. Continuous oscillation frets the sphered contacts even with C0 405 kN in reserve; keep the interfaces greased and clean and design genuine pivots separately."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54317",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54317",
      "54317 + U 317"
    ],
    "locale_variants": {}
  },
  {
    "sku": "54420-M",
    "brand": "SKF",
    "manufacturer_designation": "54420 M",
    "series": "54400-series",
    "type": "thrust_ball",
    "d_mm": 80,
    "D_mm": 210,
    "B_mm": 159.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 371,
    "static_load_kN": 1060,
    "fatigue_load_limit_kN": 31.5,
    "reference_speed_rpm": 700,
    "limiting_speed_rpm": 950,
    "max_rpm": 950,
    "weight_g": 29000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 104",
    "naming_rule_text": "Listed in SKF 17000 chapter 5, 54420 M is an ISO 104 double-direction thrust ball bearing, 80 mm bore and 210 mm OD, with a sphered housing washer and U seat washer, standing 159.9 mm high before installation. Construction is a five-component stack: one central shaft washer with tracks on both faces, two outward-facing housing washers and two cage sets, which lets one housing recess accept thrust from either direction. note the bore of 54420 M is 80 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. Envelope 80×210×159.9 mm (3.15×8.268×6.295 in), 65.0 mm radial section, C 371 kN, C0 1060 kN, Pu 31.5 kN. Mounted height H1 176 mm includes the U 420 seat washer; the bearing alone is 159.9 mm high. reference speed 700 r/min (thermal) and limiting speed 950 r/min (mechanical), catalogue mass 29000 g. Speed band width for this size is 250 r/min between reference and limiting (1.36× ratio); lubrication, preload and heat removal decide where inside that band 54420 M can actually run. Minimum-load arithmetic: with dm ≈ 145.0 mm and factor A 5.8, Fam ≈ A·(n·dm/1000)² at the 700 r/min reference speed is about 59.8 kN for 54420 M; below that preload the balls skid and smear the tracks. Washer-annulus check: the π/4·(D²−d²) contact annulus of 54420 M covers about 29,610 mm², distributing C0 1060 kN over a mean track circle of π·dm ≈ 456 mm. Light-load floor: Pu = 31.5 kN is the equivalent-load threshold below which the SKF adjusted-life equation credits very long life for 54420 M; the number is 8 % of the 371 kN dynamic rating. Stack/annulus proportions: the 159.9 mm axial stack over the 29,610 mm² washer annulus gives 5.40 mm of height per annular square millimetre ×10⁻³, and at 29000 g the bearing holds about 36.6 kN of C0 per kilogram. Heavy bidirectional self-aligning note: the two machined brass cage sets and the two sphered housing washer / U seat-washer pairs make this the heaviest standard thrust-ball execution of its bore — check both spherical interfaces for fretting at overhaul and confirm both U washers are the catalogue-matched designations before reassembly. The heaviest self-aligning thrust-ball execution of its bore: 29000 g, two machined brass cage sets and two sphered washer pairs at 176 mm installed height — plan lifting fixtures and the two U 420 articles before shutdown work starts.",
    "applications": [
      "heavy reversing hook blocks needing self-aligning seats",
      "large vertical-pump thrust with up-thrust events",
      "winch drives with bidirectional thrust on welded frames"
    ],
    "failure_modes": [
      "thermal lock-up when differential expansion removes the end play of the tighter-loaded side",
      "one-side track spalling when reversing duty dwells predominantly in one direction and only one cage set accumulates cycles",
      "point-contact destruction of the housing register when a sphered washer is operated directly on a flat face without its U seat washer",
      "asymmetric cage wear when reversing duty loads one brass cage set far more often than the other",
      "false brinelling of the stationary tracks while the machine stands under vibration",
      "rolling-contact fatigue spalling after the L10 life at the actual thrust load is exceeded"
    ],
    "pitfalls": [
      "The 371/1060 kN ratings assume the spherical contacts are free to find their seat — a painted-over or shimmed U washer fixes the angle and turns the self-aligning bearing into an edge-loaded one.",
      "Assembly is a five-component stack (central shaft washer, two cage sets, two sphered housing washers) plus the two U seat washers in the housing registers; dry-build the arrangement by hand first to confirm both sides swivel freely.",
      "Order TWO seat washers for 54420 M — the designation U 420 pairs with one side and a second U washer (same number) with the other; the catalogue 176 mm H1 includes both.",
      "The two spherical interfaces accommodate initial misalignment in either load direction but must stay clean, greased and static — continuous rocking frets the sphered contacts of even the 1060 kN static-rated set.",
      "Ordering discipline for 54420: the catalogue page quotes 54420 M plus U 420 and its 371/1060 kN ratings as one exact article; bare-number substitutions from another series or brand need a fresh dimension and rating check, not a like-for-like assumption."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 54420-M?",
        "a": "The catalogue envelope is 80×210×159.9 mm plus the 16.1 mm the U 420 seat washer adds to reach H1 176 mm, mass 29000 g; ratings C 371 kN / C0 1060 kN / Pu 31.5 kN, reference speed 700 r/min (thermal) and limiting speed 950 r/min (mechanical)."
      },
      {
        "q": "What does the designation 54420 M mean?",
        "a": "note the bore of 54420 M is 80 mm by the dimension table: the double-direction series was deliberately aligned to the 51/53 washer sets with shifted codes, so the familiar 04=20 arithmetic does not apply here. M-cage execution: brass machined from solid and ball-centred, giving heavier guidance than the standard pressed retainer at the top end of the thrust-ball range. 5 = thrust ball bearing, 4 = double direction with sphered seating surfaces."
      },
      {
        "q": "What loads can 54420-M take?",
        "a": "Pure axial load in both directions: C 371 kN, C0 1060 kN, Pu 31.5 kN, with the same minimum-load rule (factor A 5.8) in each direction; radial load is excluded."
      },
      {
        "q": "How are the two U washers ordered and fitted?",
        "a": "Order two pieces of U 420 and seat one flat-backed in each housing register with the concave faces towards the sphered housing washers; check both interfaces swivel freely before fitting the central shaft washer, and verify the mounted stack measures the 176 mm H1."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "54420",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-28",
    "last_verified": "2026-09-28",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "54420-M",
      "54420 M",
      "54420 M + U 420"
    ],
    "locale_variants": {}
  }
]
