[
  {
    "sku": "1200",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 9,
    "seal_type": "open",
    "dynamic_load_kN": 5.55,
    "static_load_kN": 1.19,
    "fatigue_load_limit_kN": 0.049,
    "limiting_speed_rpm": 22000,
    "speed_oil_rpm": 28000,
    "weight_g": 34,
    "manufacturer_designation": "1200S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1200S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1200 carries bore code 00 = 10 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 30 mm and width 9 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small electric motor and fan shafts",
      "domestic appliance drive shafts",
      "power tool spindles",
      "small pump impeller shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 1200 fits a 10 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 12xx light section at 10 mm bore uses a smaller 30 mm OD than a 1300; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1200 has no lubricant retention: grease escapes and contaminants migrate straight into the 10×30×9 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1200 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 9 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1200 self-aligning ball bearing?",
        "a": "A 1200 self-aligning ball bearing has a 10 mm bore, 30 mm outer diameter and 9 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 1200 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 1200 with code 00 has a 10 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 1200?",
        "a": "A bare 1200 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 10 mm bore?",
        "a": "The 12xx is the light section: 30×9 mm with a 10.0 mm radial section at 10 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1200-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2200",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 14,
    "seal_type": "open",
    "dynamic_load_kN": 7.45,
    "static_load_kN": 1.59,
    "fatigue_load_limit_kN": 0.067,
    "limiting_speed_rpm": 24000,
    "speed_oil_rpm": 28000,
    "weight_g": 46,
    "manufacturer_designation": "2200S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2200S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2200 carries bore code 00 = 10 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 30 mm and width 14 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "garden equipment and light machinery",
      "instrument and office machine drives",
      "small electric motor and fan shafts",
      "domestic appliance drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 2200 fits a 10 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 22xx wide-section at 10 mm bore adds load capacity through increased 14 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1200.",
      "The open 2200 has no lubricant retention: grease escapes and contaminants migrate straight into the 10×30×14 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2200 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2200."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2200 self-aligning ball bearing?",
        "a": "A 2200 self-aligning ball bearing has a 10 mm bore, 30 mm outer diameter and 14 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 2200 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 2200 with code 00 has a 10 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 2200?",
        "a": "A bare 2200 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 10 mm bore?",
        "a": "The 22xx is the wide light section: 30×14 mm with a 10.0 mm radial section at 10 mm bore, wider than a 1200 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2200-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 10×30×14 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2200-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1300",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 10,
    "D_mm": 35,
    "B_mm": 11,
    "seal_type": "open",
    "dynamic_load_kN": 7.35,
    "static_load_kN": 1.62,
    "fatigue_load_limit_kN": 0.074,
    "limiting_speed_rpm": 20000,
    "speed_oil_rpm": 24000,
    "weight_g": 59,
    "manufacturer_designation": "1300S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1300S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1300 carries bore code 00 = 10 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 35 mm and width 11 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "power tool spindles",
      "small pump impeller shafts",
      "garden equipment and light machinery",
      "instrument and office machine drives"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 1300 fits a 10 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 13xx medium section at 10 mm bore gains rating through a larger 35 mm OD and 11 mm width; verify the housing accepts the larger envelope before substituting for a 1200.",
      "The open 1300 has no lubricant retention: grease escapes and contaminants migrate straight into the 10×35×11 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1300 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1300."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1300 self-aligning ball bearing?",
        "a": "A 1300 self-aligning ball bearing has a 10 mm bore, 35 mm outer diameter and 11 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 1300 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 1300 with code 00 has a 10 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 1300?",
        "a": "A bare 1300 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 10 mm bore?",
        "a": "The 13xx is the medium section: 35×11 mm, 12.5 mm radial section at 10 mm bore, carrying more load than a 1200 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1300",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2300",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 10,
    "D_mm": 35,
    "B_mm": 17,
    "seal_type": "open",
    "dynamic_load_kN": 9.2,
    "static_load_kN": 2.01,
    "fatigue_load_limit_kN": 0.096,
    "limiting_speed_rpm": 18000,
    "speed_oil_rpm": 22000,
    "weight_g": 78,
    "manufacturer_designation": "2300S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2300S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2300 carries bore code 00 = 10 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 35 mm and width 17 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small electric motor and fan shafts",
      "domestic appliance drive shafts",
      "power tool spindles",
      "small pump impeller shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 2300 fits a 10 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 23xx heavy wide-section at 10 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2300 has no lubricant retention: grease escapes and contaminants migrate straight into the 10×35×17 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2300 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2300 self-aligning ball bearing?",
        "a": "A 2300 self-aligning ball bearing has a 10 mm bore, 35 mm outer diameter and 17 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 2300 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 2300 with code 00 has a 10 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 2300?",
        "a": "A bare 2300 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 10 mm bore?",
        "a": "The 23xx is the wide heavy section: 35×17 mm, 12.5 mm radial section at 10 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2300",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1201",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 10,
    "seal_type": "open",
    "dynamic_load_kN": 5.7,
    "static_load_kN": 1.27,
    "fatigue_load_limit_kN": 0.053,
    "limiting_speed_rpm": 22000,
    "speed_oil_rpm": 26000,
    "weight_g": 41,
    "manufacturer_designation": "1201S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1201S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1201 carries bore code 01 = 12 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 32 mm and width 10 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "domestic appliance drive shafts",
      "power tool spindles",
      "small pump impeller shafts",
      "garden equipment and light machinery"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 1201 fits a 12 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 12xx light section at 12 mm bore uses a smaller 32 mm OD than a 1301; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1201 has no lubricant retention: grease escapes and contaminants migrate straight into the 12×32×10 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1201 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1201."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1201 self-aligning ball bearing?",
        "a": "A 1201 self-aligning ball bearing has a 12 mm bore, 32 mm outer diameter and 10 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 1201 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 1201 with code 01 has a 12 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 1201?",
        "a": "A bare 1201 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 12 mm bore?",
        "a": "The 12xx is the light section: 32×10 mm with a 10.0 mm radial section at 12 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1201-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 12×32×10 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2201",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 14,
    "seal_type": "open",
    "dynamic_load_kN": 7.75,
    "static_load_kN": 1.73,
    "fatigue_load_limit_kN": 0.089,
    "limiting_speed_rpm": 22000,
    "speed_oil_rpm": 26000,
    "weight_g": 51,
    "manufacturer_designation": "2201S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2201S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2201 carries bore code 01 = 12 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 32 mm and width 14 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "instrument and office machine drives",
      "small electric motor and fan shafts",
      "domestic appliance drive shafts",
      "power tool spindles"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 2201 fits a 12 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 22xx wide-section at 12 mm bore adds load capacity through increased 14 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1201.",
      "The open 2201 has no lubricant retention: grease escapes and contaminants migrate straight into the 12×32×14 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2201 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2201 self-aligning ball bearing?",
        "a": "A 2201 self-aligning ball bearing has a 12 mm bore, 32 mm outer diameter and 14 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 2201 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 2201 with code 01 has a 12 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 2201?",
        "a": "A bare 2201 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 12 mm bore?",
        "a": "The 22xx is the wide light section: 32×14 mm with a 10.0 mm radial section at 12 mm bore, wider than a 1201 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2201-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 12×32×14 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2201-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1301",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 12,
    "D_mm": 37,
    "B_mm": 12,
    "seal_type": "open",
    "dynamic_load_kN": 9.65,
    "static_load_kN": 2.16,
    "fatigue_load_limit_kN": 0.078,
    "limiting_speed_rpm": 18000,
    "speed_oil_rpm": 22000,
    "weight_g": 68,
    "manufacturer_designation": "1301S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1301S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1301 carries bore code 01 = 12 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 37 mm and width 12 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small pump impeller shafts",
      "garden equipment and light machinery",
      "instrument and office machine drives",
      "small electric motor and fan shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 1301 fits a 12 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 13xx medium section at 12 mm bore gains rating through a larger 37 mm OD and 12 mm width; verify the housing accepts the larger envelope before substituting for a 1201.",
      "The open 1301 has no lubricant retention: grease escapes and contaminants migrate straight into the 12×37×12 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1301 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1301."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1301 self-aligning ball bearing?",
        "a": "A 1301 self-aligning ball bearing has a 12 mm bore, 37 mm outer diameter and 12 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 1301 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 1301 with code 01 has a 12 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 1301?",
        "a": "A bare 1301 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 12 mm bore?",
        "a": "The 13xx is the medium section: 37×12 mm, 12.5 mm radial section at 12 mm bore, carrying more load than a 1201 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1301-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2301",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 12,
    "D_mm": 37,
    "B_mm": 17,
    "seal_type": "open",
    "dynamic_load_kN": 12.1,
    "static_load_kN": 2.73,
    "fatigue_load_limit_kN": 0.12,
    "limiting_speed_rpm": 17000,
    "speed_oil_rpm": 22000,
    "weight_g": 87,
    "manufacturer_designation": "2301S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2301S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2301 carries bore code 01 = 12 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 37 mm and width 17 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "domestic appliance drive shafts",
      "power tool spindles",
      "small pump impeller shafts",
      "garden equipment and light machinery"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 2301 fits a 12 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 23xx heavy wide-section at 12 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2301 has no lubricant retention: grease escapes and contaminants migrate straight into the 12×37×17 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2301 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2301-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2301 self-aligning ball bearing?",
        "a": "A 2301 self-aligning ball bearing has a 12 mm bore, 37 mm outer diameter and 17 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 2301 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 2301 with code 01 has a 12 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 2301?",
        "a": "A bare 2301 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 12 mm bore?",
        "a": "The 23xx is the wide heavy section: 37×17 mm, 12.5 mm radial section at 12 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2301",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1202",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 11,
    "seal_type": "open",
    "dynamic_load_kN": 7.6,
    "static_load_kN": 1.75,
    "fatigue_load_limit_kN": 0.072,
    "limiting_speed_rpm": 18000,
    "speed_oil_rpm": 22000,
    "weight_g": 50,
    "manufacturer_designation": "1202S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1202S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1202 carries bore code 02 = 15 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 35 mm and width 11 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "power tool spindles",
      "small pump impeller shafts",
      "garden equipment and light machinery",
      "instrument and office machine drives"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 1202 fits a 15 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 12xx light section at 15 mm bore uses a smaller 35 mm OD than a 1302; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1202 has no lubricant retention: grease escapes and contaminants migrate straight into the 15×35×11 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1202 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1202."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1202 self-aligning ball bearing?",
        "a": "A 1202 self-aligning ball bearing has a 15 mm bore, 35 mm outer diameter and 11 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 1202 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 1202 with code 02 has a 15 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 1202?",
        "a": "A bare 1202 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 15 mm bore?",
        "a": "The 12xx is the light section: 35×11 mm with a 10.0 mm radial section at 15 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1202-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2202",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 14,
    "seal_type": "open",
    "dynamic_load_kN": 7.8,
    "static_load_kN": 1.85,
    "fatigue_load_limit_kN": 0.095,
    "limiting_speed_rpm": 18000,
    "speed_oil_rpm": 22000,
    "weight_g": 58,
    "manufacturer_designation": "2202S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2202S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2202 carries bore code 02 = 15 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 35 mm and width 14 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small electric motor and fan shafts",
      "domestic appliance drive shafts",
      "power tool spindles",
      "small pump impeller shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 2202 fits a 15 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 22xx wide-section at 15 mm bore adds load capacity through increased 14 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1202.",
      "The open 2202 has no lubricant retention: grease escapes and contaminants migrate straight into the 15×35×14 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2202 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2202-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2202 self-aligning ball bearing?",
        "a": "A 2202 self-aligning ball bearing has a 15 mm bore, 35 mm outer diameter and 14 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 2202 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 2202 with code 02 has a 15 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 2202?",
        "a": "A bare 2202 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 15 mm bore?",
        "a": "The 22xx is the wide light section: 35×14 mm with a 10.0 mm radial section at 15 mm bore, wider than a 1202 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2202-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×14 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2202-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "1302",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 13,
    "seal_type": "open",
    "dynamic_load_kN": 9.7,
    "static_load_kN": 2.29,
    "fatigue_load_limit_kN": 0.081,
    "limiting_speed_rpm": 16000,
    "speed_oil_rpm": 20000,
    "weight_g": 101,
    "manufacturer_designation": "1302S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1302S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1302 carries bore code 02 = 15 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 42 mm and width 13 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "garden equipment and light machinery",
      "instrument and office machine drives",
      "small electric motor and fan shafts",
      "domestic appliance drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 1302 fits a 15 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 13xx medium section at 15 mm bore gains rating through a larger 42 mm OD and 13 mm width; verify the housing accepts the larger envelope before substituting for a 1202.",
      "The open 1302 has no lubricant retention: grease escapes and contaminants migrate straight into the 15×42×13 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1302 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1302 self-aligning ball bearing?",
        "a": "A 1302 self-aligning ball bearing has a 15 mm bore, 42 mm outer diameter and 13 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 1302 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 1302 with code 02 has a 15 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 1302?",
        "a": "A bare 1302 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 15 mm bore?",
        "a": "The 13xx is the medium section: 42×13 mm, 13.5 mm radial section at 15 mm bore, carrying more load than a 1202 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1302-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×42×13 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2302",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 17,
    "seal_type": "open",
    "dynamic_load_kN": 12.3,
    "static_load_kN": 2.91,
    "fatigue_load_limit_kN": 0.13,
    "limiting_speed_rpm": 14000,
    "speed_oil_rpm": 18000,
    "weight_g": 113,
    "manufacturer_designation": "2302S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2302S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2302 carries bore code 02 = 15 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 42 mm and width 17 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "power tool spindles",
      "small pump impeller shafts",
      "garden equipment and light machinery",
      "instrument and office machine drives"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 2302 fits a 15 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 23xx heavy wide-section at 15 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2302 has no lubricant retention: grease escapes and contaminants migrate straight into the 15×42×17 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2302 units.",
      "A 15 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2302 self-aligning ball bearing?",
        "a": "A 2302 self-aligning ball bearing has a 15 mm bore, 42 mm outer diameter and 17 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 2302 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 2302 with code 02 has a 15 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 2302?",
        "a": "A bare 2302 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 15 mm bore?",
        "a": "The 23xx is the wide heavy section: 42×17 mm, 13.5 mm radial section at 15 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2302-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×42×17 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      }
    ]
  },
  {
    "sku": "1203",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 12,
    "seal_type": "open",
    "dynamic_load_kN": 8,
    "static_load_kN": 2.01,
    "fatigue_load_limit_kN": 0.083,
    "limiting_speed_rpm": 16000,
    "speed_oil_rpm": 20000,
    "weight_g": 74,
    "manufacturer_designation": "1203S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1203S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1203 carries bore code 03 = 17 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 40 mm and width 12 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small pump impeller shafts",
      "garden equipment and light machinery",
      "instrument and office machine drives",
      "small electric motor and fan shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 1203 fits a 17 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 12xx light section at 17 mm bore uses a smaller 40 mm OD than a 1303; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1203 has no lubricant retention: grease escapes and contaminants migrate straight into the 17×40×12 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1203 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1203 self-aligning ball bearing?",
        "a": "A 1203 self-aligning ball bearing has a 17 mm bore, 40 mm outer diameter and 12 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 1203 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 1203 with code 03 has a 17 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 1203?",
        "a": "A bare 1203 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 17 mm bore?",
        "a": "The 12xx is the light section: 40×12 mm with an 11.5 mm radial section at 17 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1203-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2203",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 16,
    "seal_type": "open",
    "dynamic_load_kN": 9.95,
    "static_load_kN": 2.42,
    "fatigue_load_limit_kN": 0.13,
    "limiting_speed_rpm": 16000,
    "speed_oil_rpm": 20000,
    "weight_g": 89,
    "manufacturer_designation": "2203S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2203S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2203 carries bore code 03 = 17 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 40 mm and width 16 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "domestic appliance drive shafts",
      "power tool spindles",
      "small pump impeller shafts",
      "garden equipment and light machinery"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 2203 fits a 17 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 22xx wide-section at 17 mm bore adds load capacity through increased 16 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1203.",
      "The open 2203 has no lubricant retention: grease escapes and contaminants migrate straight into the 17×40×16 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2203 units.",
      "A 17 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2203 self-aligning ball bearing?",
        "a": "A 2203 self-aligning ball bearing has a 17 mm bore, 40 mm outer diameter and 16 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 2203 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 2203 with code 03 has a 17 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 2203?",
        "a": "A bare 2203 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 17 mm bore?",
        "a": "The 22xx is the wide light section: 40×16 mm with an 11.5 mm radial section at 17 mm bore, wider than a 1203 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2203-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×16 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2203-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1303",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 14,
    "seal_type": "open",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 3.2,
    "fatigue_load_limit_kN": 0.11,
    "limiting_speed_rpm": 14000,
    "speed_oil_rpm": 17000,
    "weight_g": 130,
    "manufacturer_designation": "1303S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1303S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1303 carries bore code 03 = 17 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 47 mm and width 14 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "instrument and office machine drives",
      "small electric motor and fan shafts",
      "domestic appliance drive shafts",
      "power tool spindles"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 1303 fits a 17 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 13xx medium section at 17 mm bore gains rating through a larger 47 mm OD and 14 mm width; verify the housing accepts the larger envelope before substituting for a 1203.",
      "The open 1303 has no lubricant retention: grease escapes and contaminants migrate straight into the 17×47×14 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1303 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1303-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1303 self-aligning ball bearing?",
        "a": "A 1303 self-aligning ball bearing has a 17 mm bore, 47 mm outer diameter and 14 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 1303 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 1303 with code 03 has a 17 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 1303?",
        "a": "A bare 1303 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 17 mm bore?",
        "a": "The 13xx is the medium section: 47×14 mm, 15.0 mm radial section at 17 mm bore, carrying more load than a 1203 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1303-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2303",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 19,
    "seal_type": "open",
    "dynamic_load_kN": 14.7,
    "static_load_kN": 3.55,
    "fatigue_load_limit_kN": 0.16,
    "limiting_speed_rpm": 13000,
    "speed_oil_rpm": 16000,
    "weight_g": 160,
    "manufacturer_designation": "2303S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2303S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2303 carries bore code 03 = 17 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 47 mm and width 19 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small pump impeller shafts",
      "garden equipment and light machinery",
      "instrument and office machine drives",
      "small electric motor and fan shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 2303 fits a 17 mm shaft — the code × 5 mnemonic does not apply below code 04 (it would imply 0 mm for code 00).",
      "The 23xx heavy wide-section at 17 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2303 has no lubricant retention: grease escapes and contaminants migrate straight into the 17×47×19 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2303 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 19 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2303 self-aligning ball bearing?",
        "a": "A 2303 self-aligning ball bearing has a 17 mm bore, 47 mm outer diameter and 19 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "Why does 2303 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 2303 with code 03 has a 17 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What does the open suffix mean on 2303?",
        "a": "A bare 2303 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 17 mm bore?",
        "a": "The 23xx is the wide heavy section: 47×19 mm, 15.0 mm radial section at 17 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2303-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×19 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2303-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1204",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "seal_type": "open",
    "dynamic_load_kN": 10,
    "static_load_kN": 2.61,
    "fatigue_load_limit_kN": 0.11,
    "limiting_speed_rpm": 14000,
    "speed_oil_rpm": 17000,
    "weight_g": 120,
    "manufacturer_designation": "1204S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1204S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1204 carries bore code 04 = 20 mm. Outside diameter 47 mm and width 14 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "At a 20 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1204; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 12xx light section at 20 mm bore uses a smaller 47 mm OD than a 1304; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1204 has no lubricant retention: grease escapes and contaminants migrate straight into the 20×47×14 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1204 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1204-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1204 self-aligning ball bearing?",
        "a": "A 1204 self-aligning ball bearing has a 20 mm bore, 47 mm outer diameter and 14 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1204 bore code work?",
        "a": "The last two digits of 1204 are bore code 04, giving 04 × 5 = 20 mm bore. The 47 mm outside diameter and 14 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1204?",
        "a": "A bare 1204 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 20 mm bore?",
        "a": "The 12xx is the light section: 47×14 mm with a 13.5 mm radial section at 20 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1204-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1204-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "1204K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "seal_type": "open",
    "dynamic_load_kN": 10,
    "static_load_kN": 2.61,
    "fatigue_load_limit_kN": 0.11,
    "limiting_speed_rpm": 14000,
    "speed_oil_rpm": 17000,
    "weight_g": 120,
    "manufacturer_designation": "1204SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1204SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1204 carries bore code 04 = 20 mm. Outside diameter 47 mm and width 14 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1204. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "At a 20 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1204K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 12xx light section at 20 mm bore uses a smaller 47 mm OD than a 1304; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1204K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 20 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Shaft and housing fillets must clear the bearing chamfer so the 14 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1204K self-aligning ball bearing?",
        "a": "A 1204K self-aligning ball bearing has a 20 mm bore, 47 mm outer diameter and 14 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1204."
      },
      {
        "q": "How does the 1204 bore code work?",
        "a": "The last two digits of 1204 are bore code 04, giving 04 × 5 = 20 mm bore. The 47 mm outside diameter and 14 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1204K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1204. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 20 mm bore?",
        "a": "The 12xx is the light section: 47×14 mm with a 13.5 mm radial section at 20 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1204K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2204",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 18,
    "seal_type": "open",
    "dynamic_load_kN": 12.8,
    "static_load_kN": 3.3,
    "fatigue_load_limit_kN": 0.14,
    "limiting_speed_rpm": 14000,
    "speed_oil_rpm": 17000,
    "weight_g": 142,
    "manufacturer_designation": "2204S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2204S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2204 carries bore code 04 = 20 mm. Outside diameter 47 mm and width 18 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "At a 20 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2204; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 22xx wide-section at 20 mm bore adds load capacity through increased 18 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1204.",
      "The open 2204 has no lubricant retention: grease escapes and contaminants migrate straight into the 20×47×18 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2204 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 18 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2204 self-aligning ball bearing?",
        "a": "A 2204 self-aligning ball bearing has a 20 mm bore, 47 mm outer diameter and 18 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2204 bore code work?",
        "a": "The last two digits of 2204 are bore code 04, giving 04 × 5 = 20 mm bore. The 47 mm outside diameter and 18 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2204?",
        "a": "A bare 2204 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 20 mm bore?",
        "a": "The 22xx is the wide light section: 47×18 mm with a 13.5 mm radial section at 20 mm bore, wider than a 1204 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2204-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×18 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2204-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2204K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 18,
    "seal_type": "open",
    "dynamic_load_kN": 12.8,
    "static_load_kN": 3.3,
    "fatigue_load_limit_kN": 0.14,
    "limiting_speed_rpm": 14000,
    "speed_oil_rpm": 17000,
    "weight_g": 142,
    "manufacturer_designation": "2204SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2204SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2204 carries bore code 04 = 20 mm. Outside diameter 47 mm and width 18 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2204. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "At a 20 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2204K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 22xx wide-section at 20 mm bore adds load capacity through increased 18 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1204.",
      "Tapered-bore 2204K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 20 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2204K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2204K self-aligning ball bearing?",
        "a": "A 2204K self-aligning ball bearing has a 20 mm bore, 47 mm outer diameter and 18 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2204."
      },
      {
        "q": "How does the 2204 bore code work?",
        "a": "The last two digits of 2204 are bore code 04, giving 04 × 5 = 20 mm bore. The 47 mm outside diameter and 18 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2204K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2204. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 20 mm bore?",
        "a": "The 22xx is the wide light section: 47×18 mm with a 13.5 mm radial section at 20 mm bore, wider than a 1204 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2204K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1304",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "seal_type": "open",
    "dynamic_load_kN": 12.6,
    "static_load_kN": 3.35,
    "fatigue_load_limit_kN": 0.14,
    "limiting_speed_rpm": 12000,
    "speed_oil_rpm": 15000,
    "weight_g": 164,
    "manufacturer_designation": "1304S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1304S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1304 carries bore code 04 = 20 mm. Outside diameter 52 mm and width 15 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "At a 20 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1304; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 13xx medium section at 20 mm bore gains rating through a larger 52 mm OD and 15 mm width; verify the housing accepts the larger envelope before substituting for a 1204.",
      "The open 1304 has no lubricant retention: grease escapes and contaminants migrate straight into the 20×52×15 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1304 units.",
      "A 20 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1304 self-aligning ball bearing?",
        "a": "A 1304 self-aligning ball bearing has a 20 mm bore, 52 mm outer diameter and 15 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1304 bore code work?",
        "a": "The last two digits of 1304 are bore code 04, giving 04 × 5 = 20 mm bore. The 52 mm outside diameter and 15 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1304?",
        "a": "A bare 1304 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 20 mm bore?",
        "a": "The 13xx is the medium section: 52×15 mm, 16.0 mm radial section at 20 mm bore, carrying more load than a 1204 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1304-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "1304K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "seal_type": "open",
    "dynamic_load_kN": 12.6,
    "static_load_kN": 3.35,
    "fatigue_load_limit_kN": 0.14,
    "limiting_speed_rpm": 12000,
    "speed_oil_rpm": 15000,
    "weight_g": 164,
    "manufacturer_designation": "1304SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1304SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1304 carries bore code 04 = 20 mm. Outside diameter 52 mm and width 15 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1304. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "At a 20 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1304K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 13xx medium section at 20 mm bore gains rating through a larger 52 mm OD and 15 mm width; verify the housing accepts the larger envelope before substituting for a 1204.",
      "Tapered-bore 1304K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 20 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1304K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1304K self-aligning ball bearing?",
        "a": "A 1304K self-aligning ball bearing has a 20 mm bore, 52 mm outer diameter and 15 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1304."
      },
      {
        "q": "How does the 1304 bore code work?",
        "a": "The last two digits of 1304 are bore code 04, giving 04 × 5 = 20 mm bore. The 52 mm outside diameter and 15 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1304K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1304. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 20 mm bore?",
        "a": "The 13xx is the medium section: 52×15 mm, 16.0 mm radial section at 20 mm bore, carrying more load than a 1204 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1304K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2304",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 21,
    "seal_type": "open",
    "dynamic_load_kN": 18.5,
    "static_load_kN": 4.7,
    "fatigue_load_limit_kN": 0.21,
    "limiting_speed_rpm": 11000,
    "speed_oil_rpm": 14000,
    "weight_g": 207,
    "manufacturer_designation": "2304S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2304S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2304 carries bore code 04 = 20 mm. Outside diameter 52 mm and width 21 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "At a 20 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2304; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 23xx heavy wide-section at 20 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2304 has no lubricant retention: grease escapes and contaminants migrate straight into the 20×52×21 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2304 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 2304."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2304 self-aligning ball bearing?",
        "a": "A 2304 self-aligning ball bearing has a 20 mm bore, 52 mm outer diameter and 21 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2304 bore code work?",
        "a": "The last two digits of 2304 are bore code 04, giving 04 × 5 = 20 mm bore. The 52 mm outside diameter and 21 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2304?",
        "a": "A bare 2304 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 20 mm bore?",
        "a": "The 23xx is the wide heavy section: 52×21 mm, 16.0 mm radial section at 20 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2304-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×21 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2304-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2304K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 21,
    "seal_type": "open",
    "dynamic_load_kN": 18.5,
    "static_load_kN": 4.7,
    "fatigue_load_limit_kN": 0.21,
    "limiting_speed_rpm": 11000,
    "speed_oil_rpm": 14000,
    "weight_g": 207,
    "manufacturer_designation": "2304SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2304SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2304 carries bore code 04 = 20 mm. Outside diameter 52 mm and width 21 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2304. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "At a 20 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2304K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 23xx heavy wide-section at 20 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2304K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 20 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2304K self-aligning ball bearing?",
        "a": "A 2304K self-aligning ball bearing has a 20 mm bore, 52 mm outer diameter and 21 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2304."
      },
      {
        "q": "How does the 2304 bore code work?",
        "a": "The last two digits of 2304 are bore code 04, giving 04 × 5 = 20 mm bore. The 52 mm outside diameter and 21 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2304K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2304. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 20 mm bore?",
        "a": "The 23xx is the wide heavy section: 52×21 mm, 16.0 mm radial section at 20 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2304K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1205",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "seal_type": "open",
    "dynamic_load_kN": 12.2,
    "static_load_kN": 3.3,
    "fatigue_load_limit_kN": 0.13,
    "limiting_speed_rpm": 12000,
    "speed_oil_rpm": 14000,
    "weight_g": 140,
    "manufacturer_designation": "1205S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1205S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1205 carries bore code 05 = 25 mm. Outside diameter 52 mm and width 15 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "At a 25 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1205; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 12xx light section at 25 mm bore uses a smaller 52 mm OD than a 1305; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1205 has no lubricant retention: grease escapes and contaminants migrate straight into the 25×52×15 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1205 units.",
      "A 25 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1205 self-aligning ball bearing?",
        "a": "A 1205 self-aligning ball bearing has a 25 mm bore, 52 mm outer diameter and 15 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1205 bore code work?",
        "a": "The last two digits of 1205 are bore code 05, giving 05 × 5 = 25 mm bore. The 52 mm outside diameter and 15 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1205?",
        "a": "A bare 1205 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 25 mm bore?",
        "a": "The 12xx is the light section: 52×15 mm with a 13.5 mm radial section at 25 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1205-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1205-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "1205K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "seal_type": "open",
    "dynamic_load_kN": 12.2,
    "static_load_kN": 3.3,
    "fatigue_load_limit_kN": 0.13,
    "limiting_speed_rpm": 12000,
    "speed_oil_rpm": 14000,
    "weight_g": 140,
    "manufacturer_designation": "1205SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1205SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1205 carries bore code 05 = 25 mm. Outside diameter 52 mm and width 15 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1205. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "At a 25 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1205K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 12xx light section at 25 mm bore uses a smaller 52 mm OD than a 1305; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1205K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 25 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1205K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1205K self-aligning ball bearing?",
        "a": "A 1205K self-aligning ball bearing has a 25 mm bore, 52 mm outer diameter and 15 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1205."
      },
      {
        "q": "How does the 1205 bore code work?",
        "a": "The last two digits of 1205 are bore code 05, giving 05 × 5 = 25 mm bore. The 52 mm outside diameter and 15 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1205K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1205. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 25 mm bore?",
        "a": "The 12xx is the light section: 52×15 mm with a 13.5 mm radial section at 25 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1205K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2205",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 18,
    "seal_type": "open",
    "dynamic_load_kN": 12.4,
    "static_load_kN": 3.45,
    "fatigue_load_limit_kN": 0.2,
    "limiting_speed_rpm": 12000,
    "speed_oil_rpm": 14000,
    "weight_g": 160,
    "manufacturer_designation": "2205S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2205S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2205 carries bore code 05 = 25 mm. Outside diameter 52 mm and width 18 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "At a 25 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2205; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 22xx wide-section at 25 mm bore adds load capacity through increased 18 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1205.",
      "The open 2205 has no lubricant retention: grease escapes and contaminants migrate straight into the 25×52×18 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2205 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 2205."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2205 self-aligning ball bearing?",
        "a": "A 2205 self-aligning ball bearing has a 25 mm bore, 52 mm outer diameter and 18 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2205 bore code work?",
        "a": "The last two digits of 2205 are bore code 05, giving 05 × 5 = 25 mm bore. The 52 mm outside diameter and 18 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2205?",
        "a": "A bare 2205 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 25 mm bore?",
        "a": "The 22xx is the wide light section: 52×18 mm with a 13.5 mm radial section at 25 mm bore, wider than a 1205 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2205-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2205-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2205-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2205-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2205K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 18,
    "seal_type": "open",
    "dynamic_load_kN": 12.4,
    "static_load_kN": 3.45,
    "fatigue_load_limit_kN": 0.2,
    "limiting_speed_rpm": 12000,
    "speed_oil_rpm": 14000,
    "weight_g": 160,
    "manufacturer_designation": "2205SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2205SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2205 carries bore code 05 = 25 mm. Outside diameter 52 mm and width 18 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2205. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "At a 25 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2205K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 22xx wide-section at 25 mm bore adds load capacity through increased 18 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1205.",
      "Tapered-bore 2205K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 25 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2205K self-aligning ball bearing?",
        "a": "A 2205K self-aligning ball bearing has a 25 mm bore, 52 mm outer diameter and 18 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2205."
      },
      {
        "q": "How does the 2205 bore code work?",
        "a": "The last two digits of 2205 are bore code 05, giving 05 × 5 = 25 mm bore. The 52 mm outside diameter and 18 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2205K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2205. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 25 mm bore?",
        "a": "The 22xx is the wide light section: 52×18 mm with a 13.5 mm radial section at 25 mm bore, wider than a 1205 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2205K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1305",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "seal_type": "open",
    "dynamic_load_kN": 18.2,
    "static_load_kN": 5,
    "fatigue_load_limit_kN": 0.15,
    "limiting_speed_rpm": 10000,
    "speed_oil_rpm": 13000,
    "weight_g": 261,
    "manufacturer_designation": "1305S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1305S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1305 carries bore code 05 = 25 mm. Outside diameter 62 mm and width 17 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "At a 25 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1305; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 13xx medium section at 25 mm bore gains rating through a larger 62 mm OD and 17 mm width; verify the housing accepts the larger envelope before substituting for a 1205.",
      "The open 1305 has no lubricant retention: grease escapes and contaminants migrate straight into the 25×62×17 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1305 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 17 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1305 self-aligning ball bearing?",
        "a": "A 1305 self-aligning ball bearing has a 25 mm bore, 62 mm outer diameter and 17 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1305 bore code work?",
        "a": "The last two digits of 1305 are bore code 05, giving 05 × 5 = 25 mm bore. The 62 mm outside diameter and 17 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1305?",
        "a": "A bare 1305 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 25 mm bore?",
        "a": "The 13xx is the medium section: 62×17 mm, 18.5 mm radial section at 25 mm bore, carrying more load than a 1205 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1305-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1305-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1305K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "seal_type": "open",
    "dynamic_load_kN": 18.2,
    "static_load_kN": 5,
    "fatigue_load_limit_kN": 0.15,
    "limiting_speed_rpm": 10000,
    "speed_oil_rpm": 13000,
    "weight_g": 261,
    "manufacturer_designation": "1305SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1305SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1305 carries bore code 05 = 25 mm. Outside diameter 62 mm and width 17 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1305. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "At a 25 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1305K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 13xx medium section at 25 mm bore gains rating through a larger 62 mm OD and 17 mm width; verify the housing accepts the larger envelope before substituting for a 1205.",
      "Tapered-bore 1305K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 25 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1305K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1305K self-aligning ball bearing?",
        "a": "A 1305K self-aligning ball bearing has a 25 mm bore, 62 mm outer diameter and 17 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1305."
      },
      {
        "q": "How does the 1305 bore code work?",
        "a": "The last two digits of 1305 are bore code 05, giving 05 × 5 = 25 mm bore. The 62 mm outside diameter and 17 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1305K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1305. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 25 mm bore?",
        "a": "The 13xx is the medium section: 62×17 mm, 18.5 mm radial section at 25 mm bore, carrying more load than a 1205 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1305K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2305",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 24,
    "seal_type": "open",
    "dynamic_load_kN": 24.9,
    "static_load_kN": 6.6,
    "fatigue_load_limit_kN": 0.29,
    "limiting_speed_rpm": 9500,
    "speed_oil_rpm": 12000,
    "weight_g": 332,
    "manufacturer_designation": "2305S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2305S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2305 carries bore code 05 = 25 mm. Outside diameter 62 mm and width 24 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "At a 25 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2305; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 23xx heavy wide-section at 25 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2305 has no lubricant retention: grease escapes and contaminants migrate straight into the 25×62×24 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2305 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2305."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2305 self-aligning ball bearing?",
        "a": "A 2305 self-aligning ball bearing has a 25 mm bore, 62 mm outer diameter and 24 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2305 bore code work?",
        "a": "The last two digits of 2305 are bore code 05, giving 05 × 5 = 25 mm bore. The 62 mm outside diameter and 24 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2305?",
        "a": "A bare 2305 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 25 mm bore?",
        "a": "The 23xx is the wide heavy section: 62×24 mm, 18.5 mm radial section at 25 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2305-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×24 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2305-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×24 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2305-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2305-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2305K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 24,
    "seal_type": "open",
    "dynamic_load_kN": 24.9,
    "static_load_kN": 6.6,
    "fatigue_load_limit_kN": 0.29,
    "limiting_speed_rpm": 9500,
    "speed_oil_rpm": 12000,
    "weight_g": 332,
    "manufacturer_designation": "2305SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2305SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2305 carries bore code 05 = 25 mm. Outside diameter 62 mm and width 24 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2305. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "At a 25 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2305K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 23xx heavy wide-section at 25 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2305K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 25 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2305-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2305K self-aligning ball bearing?",
        "a": "A 2305K self-aligning ball bearing has a 25 mm bore, 62 mm outer diameter and 24 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2305."
      },
      {
        "q": "How does the 2305 bore code work?",
        "a": "The last two digits of 2305 are bore code 05, giving 05 × 5 = 25 mm bore. The 62 mm outside diameter and 24 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2305K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2305. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 25 mm bore?",
        "a": "The 23xx is the wide heavy section: 62×24 mm, 18.5 mm radial section at 25 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2305K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1206",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "seal_type": "open",
    "dynamic_load_kN": 15.8,
    "static_load_kN": 4.65,
    "fatigue_load_limit_kN": 0.19,
    "limiting_speed_rpm": 10000,
    "speed_oil_rpm": 12000,
    "weight_g": 220,
    "manufacturer_designation": "1206S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1206S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1206 carries bore code 06 = 30 mm. Outside diameter 62 mm and width 16 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "At a 30 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1206; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 12xx light section at 30 mm bore uses a smaller 62 mm OD than a 1306; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1206 has no lubricant retention: grease escapes and contaminants migrate straight into the 30×62×16 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1206 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 16 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1206 self-aligning ball bearing?",
        "a": "A 1206 self-aligning ball bearing has a 30 mm bore, 62 mm outer diameter and 16 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1206 bore code work?",
        "a": "The last two digits of 1206 are bore code 06, giving 06 × 5 = 30 mm bore. The 62 mm outside diameter and 16 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1206?",
        "a": "A bare 1206 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 30 mm bore?",
        "a": "The 12xx is the light section: 62×16 mm with a 16.0 mm radial section at 30 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1206-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1206-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1206K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "seal_type": "open",
    "dynamic_load_kN": 15.8,
    "static_load_kN": 4.65,
    "fatigue_load_limit_kN": 0.19,
    "limiting_speed_rpm": 10000,
    "speed_oil_rpm": 12000,
    "weight_g": 220,
    "manufacturer_designation": "1206SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1206SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1206 carries bore code 06 = 30 mm. Outside diameter 62 mm and width 16 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1206. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "At a 30 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1206K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 12xx light section at 30 mm bore uses a smaller 62 mm OD than a 1306; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1206K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 30 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1206K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1206K self-aligning ball bearing?",
        "a": "A 1206K self-aligning ball bearing has a 30 mm bore, 62 mm outer diameter and 16 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1206."
      },
      {
        "q": "How does the 1206 bore code work?",
        "a": "The last two digits of 1206 are bore code 06, giving 06 × 5 = 30 mm bore. The 62 mm outside diameter and 16 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1206K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1206. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 30 mm bore?",
        "a": "The 12xx is the light section: 62×16 mm with a 16.0 mm radial section at 30 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1206K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2206",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 20,
    "seal_type": "open",
    "dynamic_load_kN": 15.3,
    "static_load_kN": 4.55,
    "fatigue_load_limit_kN": 0.26,
    "limiting_speed_rpm": 10000,
    "speed_oil_rpm": 12000,
    "weight_g": 262,
    "manufacturer_designation": "2206S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2206S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2206 carries bore code 06 = 30 mm. Outside diameter 62 mm and width 20 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "At a 30 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2206; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 22xx wide-section at 30 mm bore adds load capacity through increased 20 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1206.",
      "The open 2206 has no lubricant retention: grease escapes and contaminants migrate straight into the 30×62×20 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2206 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2206."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2206 self-aligning ball bearing?",
        "a": "A 2206 self-aligning ball bearing has a 30 mm bore, 62 mm outer diameter and 20 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2206 bore code work?",
        "a": "The last two digits of 2206 are bore code 06, giving 06 × 5 = 30 mm bore. The 62 mm outside diameter and 20 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2206?",
        "a": "A bare 2206 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 30 mm bore?",
        "a": "The 22xx is the wide light section: 62×20 mm with a 16.0 mm radial section at 30 mm bore, wider than a 1206 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2206-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2206-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2206-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2206-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2206K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 20,
    "seal_type": "open",
    "dynamic_load_kN": 15.3,
    "static_load_kN": 4.55,
    "fatigue_load_limit_kN": 0.26,
    "limiting_speed_rpm": 10000,
    "speed_oil_rpm": 12000,
    "weight_g": 262,
    "manufacturer_designation": "2206SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2206SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2206 carries bore code 06 = 30 mm. Outside diameter 62 mm and width 20 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2206. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "At a 30 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2206K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 22xx wide-section at 30 mm bore adds load capacity through increased 20 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1206.",
      "Tapered-bore 2206K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 30 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2206-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2206K self-aligning ball bearing?",
        "a": "A 2206K self-aligning ball bearing has a 30 mm bore, 62 mm outer diameter and 20 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2206."
      },
      {
        "q": "How does the 2206 bore code work?",
        "a": "The last two digits of 2206 are bore code 06, giving 06 × 5 = 30 mm bore. The 62 mm outside diameter and 20 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2206K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2206. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 30 mm bore?",
        "a": "The 22xx is the wide light section: 62×20 mm with a 16.0 mm radial section at 30 mm bore, wider than a 1206 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2206K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1306",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "seal_type": "open",
    "dynamic_load_kN": 21.4,
    "static_load_kN": 6.3,
    "fatigue_load_limit_kN": 0.19,
    "limiting_speed_rpm": 8500,
    "speed_oil_rpm": 11000,
    "weight_g": 391,
    "manufacturer_designation": "1306S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1306S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1306 carries bore code 06 = 30 mm. Outside diameter 72 mm and width 19 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "At a 30 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1306; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 13xx medium section at 30 mm bore gains rating through a larger 72 mm OD and 19 mm width; verify the housing accepts the larger envelope before substituting for a 1206.",
      "The open 1306 has no lubricant retention: grease escapes and contaminants migrate straight into the 30×72×19 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1306 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1306."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1306 self-aligning ball bearing?",
        "a": "A 1306 self-aligning ball bearing has a 30 mm bore, 72 mm outer diameter and 19 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1306 bore code work?",
        "a": "The last two digits of 1306 are bore code 06, giving 06 × 5 = 30 mm bore. The 72 mm outside diameter and 19 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1306?",
        "a": "A bare 1306 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 30 mm bore?",
        "a": "The 13xx is the medium section: 72×19 mm, 21.0 mm radial section at 30 mm bore, carrying more load than a 1206 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1306-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1306-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1306K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "seal_type": "open",
    "dynamic_load_kN": 21.4,
    "static_load_kN": 6.3,
    "fatigue_load_limit_kN": 0.19,
    "limiting_speed_rpm": 8500,
    "speed_oil_rpm": 11000,
    "weight_g": 391,
    "manufacturer_designation": "1306SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1306SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1306 carries bore code 06 = 30 mm. Outside diameter 72 mm and width 19 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1306. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "At a 30 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1306K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 13xx medium section at 30 mm bore gains rating through a larger 72 mm OD and 19 mm width; verify the housing accepts the larger envelope before substituting for a 1206.",
      "Tapered-bore 1306K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 30 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1306K self-aligning ball bearing?",
        "a": "A 1306K self-aligning ball bearing has a 30 mm bore, 72 mm outer diameter and 19 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1306."
      },
      {
        "q": "How does the 1306 bore code work?",
        "a": "The last two digits of 1306 are bore code 06, giving 06 × 5 = 30 mm bore. The 72 mm outside diameter and 19 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1306K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1306. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 30 mm bore?",
        "a": "The 13xx is the medium section: 72×19 mm, 21.0 mm radial section at 30 mm bore, carrying more load than a 1206 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1306K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2306",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 27,
    "seal_type": "open",
    "dynamic_load_kN": 32,
    "static_load_kN": 8.75,
    "fatigue_load_limit_kN": 0.38,
    "limiting_speed_rpm": 8000,
    "speed_oil_rpm": 10000,
    "weight_g": 500,
    "manufacturer_designation": "2306S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2306S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2306 carries bore code 06 = 30 mm. Outside diameter 72 mm and width 27 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "At a 30 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2306; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 23xx heavy wide-section at 30 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2306 has no lubricant retention: grease escapes and contaminants migrate straight into the 30×72×27 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2306 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2306 self-aligning ball bearing?",
        "a": "A 2306 self-aligning ball bearing has a 30 mm bore, 72 mm outer diameter and 27 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2306 bore code work?",
        "a": "The last two digits of 2306 are bore code 06, giving 06 × 5 = 30 mm bore. The 72 mm outside diameter and 27 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2306?",
        "a": "A bare 2306 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 30 mm bore?",
        "a": "The 23xx is the wide heavy section: 72×27 mm, 21.0 mm radial section at 30 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2306-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×27 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2306-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×27 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2306-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2306K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 27,
    "seal_type": "open",
    "dynamic_load_kN": 32,
    "static_load_kN": 8.75,
    "fatigue_load_limit_kN": 0.38,
    "limiting_speed_rpm": 8000,
    "speed_oil_rpm": 10000,
    "weight_g": 500,
    "manufacturer_designation": "2306SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2306SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2306 carries bore code 06 = 30 mm. Outside diameter 72 mm and width 27 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2306. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "At a 30 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2306K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 23xx heavy wide-section at 30 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2306K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 30 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "A 30 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2306K self-aligning ball bearing?",
        "a": "A 2306K self-aligning ball bearing has a 30 mm bore, 72 mm outer diameter and 27 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2306."
      },
      {
        "q": "How does the 2306 bore code work?",
        "a": "The last two digits of 2306 are bore code 06, giving 06 × 5 = 30 mm bore. The 72 mm outside diameter and 27 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2306K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2306. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 30 mm bore?",
        "a": "The 23xx is the wide heavy section: 72×27 mm, 21.0 mm radial section at 30 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2306K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1207",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "seal_type": "open",
    "dynamic_load_kN": 15.9,
    "static_load_kN": 5.1,
    "fatigue_load_limit_kN": 0.21,
    "limiting_speed_rpm": 8500,
    "speed_oil_rpm": 10000,
    "weight_g": 330,
    "manufacturer_designation": "1207S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1207S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1207 carries bore code 07 = 35 mm. Outside diameter 72 mm and width 17 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "At a 35 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1207; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 12xx light section at 35 mm bore uses a smaller 72 mm OD than a 1307; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1207 has no lubricant retention: grease escapes and contaminants migrate straight into the 35×72×17 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1207 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1207."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1207 self-aligning ball bearing?",
        "a": "A 1207 self-aligning ball bearing has a 35 mm bore, 72 mm outer diameter and 17 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1207 bore code work?",
        "a": "The last two digits of 1207 are bore code 07, giving 07 × 5 = 35 mm bore. The 72 mm outside diameter and 17 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1207?",
        "a": "A bare 1207 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 35 mm bore?",
        "a": "The 12xx is the light section: 72×17 mm with an 18.5 mm radial section at 35 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1207-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1207-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "1207K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "seal_type": "open",
    "dynamic_load_kN": 15.9,
    "static_load_kN": 5.1,
    "fatigue_load_limit_kN": 0.21,
    "limiting_speed_rpm": 8500,
    "speed_oil_rpm": 10000,
    "weight_g": 330,
    "manufacturer_designation": "1207SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1207SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1207 carries bore code 07 = 35 mm. Outside diameter 72 mm and width 17 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1207. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "At a 35 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1207K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 12xx light section at 35 mm bore uses a smaller 72 mm OD than a 1307; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1207K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 35 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1207K self-aligning ball bearing?",
        "a": "A 1207K self-aligning ball bearing has a 35 mm bore, 72 mm outer diameter and 17 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1207."
      },
      {
        "q": "How does the 1207 bore code work?",
        "a": "The last two digits of 1207 are bore code 07, giving 07 × 5 = 35 mm bore. The 72 mm outside diameter and 17 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1207K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1207. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 35 mm bore?",
        "a": "The 12xx is the light section: 72×17 mm with an 18.5 mm radial section at 35 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1207K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2207",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 23,
    "seal_type": "open",
    "dynamic_load_kN": 21.7,
    "static_load_kN": 6.6,
    "fatigue_load_limit_kN": 0.32,
    "limiting_speed_rpm": 8500,
    "speed_oil_rpm": 10000,
    "weight_g": 403,
    "manufacturer_designation": "2207S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2207S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2207 carries bore code 07 = 35 mm. Outside diameter 72 mm and width 23 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "At a 35 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2207; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 22xx wide-section at 35 mm bore adds load capacity through increased 23 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1207.",
      "The open 2207 has no lubricant retention: grease escapes and contaminants migrate straight into the 35×72×23 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2207 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2207 self-aligning ball bearing?",
        "a": "A 2207 self-aligning ball bearing has a 35 mm bore, 72 mm outer diameter and 23 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2207 bore code work?",
        "a": "The last two digits of 2207 are bore code 07, giving 07 × 5 = 35 mm bore. The 72 mm outside diameter and 23 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2207?",
        "a": "A bare 2207 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 35 mm bore?",
        "a": "The 22xx is the wide light section: 72×23 mm with an 18.5 mm radial section at 35 mm bore, wider than a 1207 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2207-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2207-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2207-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2207-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2207K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 23,
    "seal_type": "open",
    "dynamic_load_kN": 21.7,
    "static_load_kN": 6.6,
    "fatigue_load_limit_kN": 0.32,
    "limiting_speed_rpm": 8500,
    "speed_oil_rpm": 10000,
    "weight_g": 403,
    "manufacturer_designation": "2207SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2207SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2207 carries bore code 07 = 35 mm. Outside diameter 72 mm and width 23 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2207. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "At a 35 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2207K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 22xx wide-section at 35 mm bore adds load capacity through increased 23 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1207.",
      "Tapered-bore 2207K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 35 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "A 35 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2207K self-aligning ball bearing?",
        "a": "A 2207K self-aligning ball bearing has a 35 mm bore, 72 mm outer diameter and 23 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2207."
      },
      {
        "q": "How does the 2207 bore code work?",
        "a": "The last two digits of 2207 are bore code 07, giving 07 × 5 = 35 mm bore. The 72 mm outside diameter and 23 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2207K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2207. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 35 mm bore?",
        "a": "The 22xx is the wide light section: 72×23 mm with an 18.5 mm radial section at 35 mm bore, wider than a 1207 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2207K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1307",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "seal_type": "open",
    "dynamic_load_kN": 25.3,
    "static_load_kN": 7.85,
    "fatigue_load_limit_kN": 0.28,
    "limiting_speed_rpm": 7500,
    "speed_oil_rpm": 9500,
    "weight_g": 520,
    "manufacturer_designation": "1307S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1307S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1307 carries bore code 07 = 35 mm. Outside diameter 80 mm and width 21 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "At a 35 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1307; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 13xx medium section at 35 mm bore gains rating through a larger 80 mm OD and 21 mm width; verify the housing accepts the larger envelope before substituting for a 1207.",
      "The open 1307 has no lubricant retention: grease escapes and contaminants migrate straight into the 35×80×21 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1307 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1307."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1307 self-aligning ball bearing?",
        "a": "A 1307 self-aligning ball bearing has a 35 mm bore, 80 mm outer diameter and 21 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1307 bore code work?",
        "a": "The last two digits of 1307 are bore code 07, giving 07 × 5 = 35 mm bore. The 80 mm outside diameter and 21 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1307?",
        "a": "A bare 1307 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 35 mm bore?",
        "a": "The 13xx is the medium section: 80×21 mm, 22.5 mm radial section at 35 mm bore, carrying more load than a 1207 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1307-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1307-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1307K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "seal_type": "open",
    "dynamic_load_kN": 25.3,
    "static_load_kN": 7.85,
    "fatigue_load_limit_kN": 0.28,
    "limiting_speed_rpm": 7500,
    "speed_oil_rpm": 9500,
    "weight_g": 520,
    "manufacturer_designation": "1307SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1307SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1307 carries bore code 07 = 35 mm. Outside diameter 80 mm and width 21 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1307. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "At a 35 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1307K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 13xx medium section at 35 mm bore gains rating through a larger 80 mm OD and 21 mm width; verify the housing accepts the larger envelope before substituting for a 1207.",
      "Tapered-bore 1307K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 35 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1307-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1307K self-aligning ball bearing?",
        "a": "A 1307K self-aligning ball bearing has a 35 mm bore, 80 mm outer diameter and 21 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1307."
      },
      {
        "q": "How does the 1307 bore code work?",
        "a": "The last two digits of 1307 are bore code 07, giving 07 × 5 = 35 mm bore. The 80 mm outside diameter and 21 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1307K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1307. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 35 mm bore?",
        "a": "The 13xx is the medium section: 80×21 mm, 22.5 mm radial section at 35 mm bore, carrying more load than a 1207 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1307K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2307",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 31,
    "seal_type": "open",
    "dynamic_load_kN": 40,
    "static_load_kN": 11.3,
    "fatigue_load_limit_kN": 0.48,
    "limiting_speed_rpm": 7100,
    "speed_oil_rpm": 9000,
    "weight_g": 671,
    "manufacturer_designation": "2307S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2307S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2307 carries bore code 07 = 35 mm. Outside diameter 80 mm and width 31 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "At a 35 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2307; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 23xx heavy wide-section at 35 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2307 has no lubricant retention: grease escapes and contaminants migrate straight into the 35×80×31 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2307 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2307-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2307 self-aligning ball bearing?",
        "a": "A 2307 self-aligning ball bearing has a 35 mm bore, 80 mm outer diameter and 31 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2307 bore code work?",
        "a": "The last two digits of 2307 are bore code 07, giving 07 × 5 = 35 mm bore. The 80 mm outside diameter and 31 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2307?",
        "a": "A bare 2307 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 35 mm bore?",
        "a": "The 23xx is the wide heavy section: 80×31 mm, 22.5 mm radial section at 35 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2307-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×31 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2307-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×31 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2307-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2307-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2307K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 31,
    "seal_type": "open",
    "dynamic_load_kN": 40,
    "static_load_kN": 11.3,
    "fatigue_load_limit_kN": 0.48,
    "limiting_speed_rpm": 7100,
    "speed_oil_rpm": 9000,
    "weight_g": 671,
    "manufacturer_designation": "2307SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2307SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2307 carries bore code 07 = 35 mm. Outside diameter 80 mm and width 31 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2307. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "At a 35 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2307K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 23xx heavy wide-section at 35 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2307K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 35 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Shaft and housing fillets must clear the bearing chamfer so the 31 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2307K self-aligning ball bearing?",
        "a": "A 2307K self-aligning ball bearing has a 35 mm bore, 80 mm outer diameter and 31 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2307."
      },
      {
        "q": "How does the 2307 bore code work?",
        "a": "The last two digits of 2307 are bore code 07, giving 07 × 5 = 35 mm bore. The 80 mm outside diameter and 31 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2307K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2307. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 35 mm bore?",
        "a": "The 23xx is the wide heavy section: 80×31 mm, 22.5 mm radial section at 35 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2307K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1208",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "seal_type": "open",
    "dynamic_load_kN": 19.3,
    "static_load_kN": 6.5,
    "fatigue_load_limit_kN": 0.26,
    "limiting_speed_rpm": 7500,
    "speed_oil_rpm": 9000,
    "weight_g": 420,
    "manufacturer_designation": "1208S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1208S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1208 carries bore code 08 = 40 mm. Outside diameter 80 mm and width 18 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "At a 40 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1208; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 12xx light section at 40 mm bore uses a smaller 80 mm OD than a 1308; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1208 has no lubricant retention: grease escapes and contaminants migrate straight into the 40×80×18 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1208 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1208."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1208 self-aligning ball bearing?",
        "a": "A 1208 self-aligning ball bearing has a 40 mm bore, 80 mm outer diameter and 18 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1208 bore code work?",
        "a": "The last two digits of 1208 are bore code 08, giving 08 × 5 = 40 mm bore. The 80 mm outside diameter and 18 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1208?",
        "a": "A bare 1208 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 40 mm bore?",
        "a": "The 12xx is the light section: 80×18 mm with a 20.0 mm radial section at 40 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1208-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1208-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1208K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "seal_type": "open",
    "dynamic_load_kN": 19.3,
    "static_load_kN": 6.5,
    "fatigue_load_limit_kN": 0.26,
    "limiting_speed_rpm": 7500,
    "speed_oil_rpm": 9000,
    "weight_g": 420,
    "manufacturer_designation": "1208SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1208SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1208 carries bore code 08 = 40 mm. Outside diameter 80 mm and width 18 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1208. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "At a 40 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1208K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 12xx light section at 40 mm bore uses a smaller 80 mm OD than a 1308; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1208K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 40 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1208-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1208K self-aligning ball bearing?",
        "a": "A 1208K self-aligning ball bearing has a 40 mm bore, 80 mm outer diameter and 18 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1208."
      },
      {
        "q": "How does the 1208 bore code work?",
        "a": "The last two digits of 1208 are bore code 08, giving 08 × 5 = 40 mm bore. The 80 mm outside diameter and 18 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1208K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1208. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 40 mm bore?",
        "a": "The 12xx is the light section: 80×18 mm with a 20.0 mm radial section at 40 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1208K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2208",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 23,
    "seal_type": "open",
    "dynamic_load_kN": 22.4,
    "static_load_kN": 7.35,
    "fatigue_load_limit_kN": 0.39,
    "limiting_speed_rpm": 7500,
    "speed_oil_rpm": 9000,
    "weight_g": 506,
    "manufacturer_designation": "2208S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2208S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2208 carries bore code 08 = 40 mm. Outside diameter 80 mm and width 23 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "At a 40 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2208; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 22xx wide-section at 40 mm bore adds load capacity through increased 23 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1208.",
      "The open 2208 has no lubricant retention: grease escapes and contaminants migrate straight into the 40×80×23 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2208 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2208-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2208 self-aligning ball bearing?",
        "a": "A 2208 self-aligning ball bearing has a 40 mm bore, 80 mm outer diameter and 23 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2208 bore code work?",
        "a": "The last two digits of 2208 are bore code 08, giving 08 × 5 = 40 mm bore. The 80 mm outside diameter and 23 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2208?",
        "a": "A bare 2208 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 40 mm bore?",
        "a": "The 22xx is the wide light section: 80×23 mm with a 20.0 mm radial section at 40 mm bore, wider than a 1208 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2208-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2208-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2208-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2208-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2208K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 23,
    "seal_type": "open",
    "dynamic_load_kN": 22.4,
    "static_load_kN": 7.35,
    "fatigue_load_limit_kN": 0.39,
    "limiting_speed_rpm": 7500,
    "speed_oil_rpm": 9000,
    "weight_g": 506,
    "manufacturer_designation": "2208SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2208SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2208 carries bore code 08 = 40 mm. Outside diameter 80 mm and width 23 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2208. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "At a 40 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2208K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 22xx wide-section at 40 mm bore adds load capacity through increased 23 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1208.",
      "Tapered-bore 2208K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 40 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Shaft and housing fillets must clear the bearing chamfer so the 23 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2208K self-aligning ball bearing?",
        "a": "A 2208K self-aligning ball bearing has a 40 mm bore, 80 mm outer diameter and 23 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2208."
      },
      {
        "q": "How does the 2208 bore code work?",
        "a": "The last two digits of 2208 are bore code 08, giving 08 × 5 = 40 mm bore. The 80 mm outside diameter and 23 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2208K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2208. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 40 mm bore?",
        "a": "The 22xx is the wide light section: 80×23 mm with a 20.0 mm radial section at 40 mm bore, wider than a 1208 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2208K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1308",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "seal_type": "open",
    "dynamic_load_kN": 29.8,
    "static_load_kN": 9.7,
    "fatigue_load_limit_kN": 0.3,
    "limiting_speed_rpm": 6700,
    "speed_oil_rpm": 8500,
    "weight_g": 727,
    "manufacturer_designation": "1308S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1308S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1308 carries bore code 08 = 40 mm. Outside diameter 90 mm and width 23 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "At a 40 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1308; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 13xx medium section at 40 mm bore gains rating through a larger 90 mm OD and 23 mm width; verify the housing accepts the larger envelope before substituting for a 1208.",
      "The open 1308 has no lubricant retention: grease escapes and contaminants migrate straight into the 40×90×23 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1308 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1308 self-aligning ball bearing?",
        "a": "A 1308 self-aligning ball bearing has a 40 mm bore, 90 mm outer diameter and 23 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1308 bore code work?",
        "a": "The last two digits of 1308 are bore code 08, giving 08 × 5 = 40 mm bore. The 90 mm outside diameter and 23 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1308?",
        "a": "A bare 1308 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 40 mm bore?",
        "a": "The 13xx is the medium section: 90×23 mm, 25.0 mm radial section at 40 mm bore, carrying more load than a 1208 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1308-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1308-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "1308K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "seal_type": "open",
    "dynamic_load_kN": 29.8,
    "static_load_kN": 9.7,
    "fatigue_load_limit_kN": 0.3,
    "limiting_speed_rpm": 6700,
    "speed_oil_rpm": 8500,
    "weight_g": 727,
    "manufacturer_designation": "1308SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1308SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1308 carries bore code 08 = 40 mm. Outside diameter 90 mm and width 23 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1308. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "At a 40 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1308K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 13xx medium section at 40 mm bore gains rating through a larger 90 mm OD and 23 mm width; verify the housing accepts the larger envelope before substituting for a 1208.",
      "Tapered-bore 1308K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 40 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "A 40 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1308K self-aligning ball bearing?",
        "a": "A 1308K self-aligning ball bearing has a 40 mm bore, 90 mm outer diameter and 23 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1308."
      },
      {
        "q": "How does the 1308 bore code work?",
        "a": "The last two digits of 1308 are bore code 08, giving 08 × 5 = 40 mm bore. The 90 mm outside diameter and 23 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1308K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1308. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 40 mm bore?",
        "a": "The 13xx is the medium section: 90×23 mm, 25.0 mm radial section at 40 mm bore, carrying more load than a 1208 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1308K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2308",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 33,
    "seal_type": "open",
    "dynamic_load_kN": 45.5,
    "static_load_kN": 13.5,
    "fatigue_load_limit_kN": 0.58,
    "limiting_speed_rpm": 6300,
    "speed_oil_rpm": 8000,
    "weight_g": 918,
    "manufacturer_designation": "2308S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2308S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2308 carries bore code 08 = 40 mm. Outside diameter 90 mm and width 33 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "At a 40 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2308; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 23xx heavy wide-section at 40 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2308 has no lubricant retention: grease escapes and contaminants migrate straight into the 40×90×33 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2308 units.",
      "A 40 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2308 self-aligning ball bearing?",
        "a": "A 2308 self-aligning ball bearing has a 40 mm bore, 90 mm outer diameter and 33 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2308 bore code work?",
        "a": "The last two digits of 2308 are bore code 08, giving 08 × 5 = 40 mm bore. The 90 mm outside diameter and 33 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2308?",
        "a": "A bare 2308 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 40 mm bore?",
        "a": "The 23xx is the wide heavy section: 90×33 mm, 25.0 mm radial section at 40 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2308-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2308-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2308-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2308-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2308K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 33,
    "seal_type": "open",
    "dynamic_load_kN": 45.5,
    "static_load_kN": 13.5,
    "fatigue_load_limit_kN": 0.58,
    "limiting_speed_rpm": 6300,
    "speed_oil_rpm": 8000,
    "weight_g": 918,
    "manufacturer_designation": "2308SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2308SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2308 carries bore code 08 = 40 mm. Outside diameter 90 mm and width 33 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2308. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "At a 40 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2308K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 23xx heavy wide-section at 40 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2308K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 40 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 2308K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2308K self-aligning ball bearing?",
        "a": "A 2308K self-aligning ball bearing has a 40 mm bore, 90 mm outer diameter and 33 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2308."
      },
      {
        "q": "How does the 2308 bore code work?",
        "a": "The last two digits of 2308 are bore code 08, giving 08 × 5 = 40 mm bore. The 90 mm outside diameter and 33 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2308K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2308. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 40 mm bore?",
        "a": "The 23xx is the wide heavy section: 90×33 mm, 25.0 mm radial section at 40 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2308K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1209",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "seal_type": "open",
    "dynamic_load_kN": 22,
    "static_load_kN": 7.35,
    "fatigue_load_limit_kN": 0.29,
    "limiting_speed_rpm": 7100,
    "speed_oil_rpm": 8500,
    "weight_g": 470,
    "manufacturer_designation": "1209S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1209S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1209 carries bore code 09 = 45 mm. Outside diameter 85 mm and width 19 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "At a 45 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1209; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 12xx light section at 45 mm bore uses a smaller 85 mm OD than a 1309; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1209 has no lubricant retention: grease escapes and contaminants migrate straight into the 45×85×19 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1209 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1209 self-aligning ball bearing?",
        "a": "A 1209 self-aligning ball bearing has a 45 mm bore, 85 mm outer diameter and 19 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1209 bore code work?",
        "a": "The last two digits of 1209 are bore code 09, giving 09 × 5 = 45 mm bore. The 85 mm outside diameter and 19 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1209?",
        "a": "A bare 1209 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 45 mm bore?",
        "a": "The 12xx is the light section: 85×19 mm with a 20.0 mm radial section at 45 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1209-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1209-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1209K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "seal_type": "open",
    "dynamic_load_kN": 22,
    "static_load_kN": 7.35,
    "fatigue_load_limit_kN": 0.29,
    "limiting_speed_rpm": 7100,
    "speed_oil_rpm": 8500,
    "weight_g": 470,
    "manufacturer_designation": "1209SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1209SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1209 carries bore code 09 = 45 mm. Outside diameter 85 mm and width 19 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1209. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "At a 45 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1209K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 12xx light section at 45 mm bore uses a smaller 85 mm OD than a 1309; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1209K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 45 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "A 45 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1209K self-aligning ball bearing?",
        "a": "A 1209K self-aligning ball bearing has a 45 mm bore, 85 mm outer diameter and 19 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1209."
      },
      {
        "q": "How does the 1209 bore code work?",
        "a": "The last two digits of 1209 are bore code 09, giving 09 × 5 = 45 mm bore. The 85 mm outside diameter and 19 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1209K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1209. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 45 mm bore?",
        "a": "The 12xx is the light section: 85×19 mm with a 20.0 mm radial section at 45 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1209K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2209",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 23,
    "seal_type": "open",
    "dynamic_load_kN": 23.3,
    "static_load_kN": 8.15,
    "fatigue_load_limit_kN": 0.51,
    "limiting_speed_rpm": 7100,
    "speed_oil_rpm": 8500,
    "weight_g": 556,
    "manufacturer_designation": "2209S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2209S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2209 carries bore code 09 = 45 mm. Outside diameter 85 mm and width 23 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "At a 45 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2209; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 22xx wide-section at 45 mm bore adds load capacity through increased 23 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1209.",
      "The open 2209 has no lubricant retention: grease escapes and contaminants migrate straight into the 45×85×23 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2209 units.",
      "A 45 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2209 self-aligning ball bearing?",
        "a": "A 2209 self-aligning ball bearing has a 45 mm bore, 85 mm outer diameter and 23 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2209 bore code work?",
        "a": "The last two digits of 2209 are bore code 09, giving 09 × 5 = 45 mm bore. The 85 mm outside diameter and 23 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2209?",
        "a": "A bare 2209 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 45 mm bore?",
        "a": "The 22xx is the wide light section: 85×23 mm with a 20.0 mm radial section at 45 mm bore, wider than a 1209 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2209-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2209-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2209-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2209-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2209K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 23,
    "seal_type": "open",
    "dynamic_load_kN": 23.3,
    "static_load_kN": 8.15,
    "fatigue_load_limit_kN": 0.51,
    "limiting_speed_rpm": 7100,
    "speed_oil_rpm": 8500,
    "weight_g": 556,
    "manufacturer_designation": "2209SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2209SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2209 carries bore code 09 = 45 mm. Outside diameter 85 mm and width 23 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2209. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "At a 45 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2209K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 22xx wide-section at 45 mm bore adds load capacity through increased 23 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1209.",
      "Tapered-bore 2209K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 45 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 2209K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2209K self-aligning ball bearing?",
        "a": "A 2209K self-aligning ball bearing has a 45 mm bore, 85 mm outer diameter and 23 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2209."
      },
      {
        "q": "How does the 2209 bore code work?",
        "a": "The last two digits of 2209 are bore code 09, giving 09 × 5 = 45 mm bore. The 85 mm outside diameter and 23 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2209K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2209. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 45 mm bore?",
        "a": "The 22xx is the wide light section: 85×23 mm with a 20.0 mm radial section at 45 mm bore, wider than a 1209 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2209K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1309",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "seal_type": "open",
    "dynamic_load_kN": 38.5,
    "static_load_kN": 12.7,
    "fatigue_load_limit_kN": 0.33,
    "limiting_speed_rpm": 6000,
    "speed_oil_rpm": 7500,
    "weight_g": 971,
    "manufacturer_designation": "1309S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1309S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1309 carries bore code 09 = 45 mm. Outside diameter 100 mm and width 25 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "At a 45 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1309; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 13xx medium section at 45 mm bore gains rating through a larger 100 mm OD and 25 mm width; verify the housing accepts the larger envelope before substituting for a 1209.",
      "The open 1309 has no lubricant retention: grease escapes and contaminants migrate straight into the 45×100×25 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1309 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1309-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1309 self-aligning ball bearing?",
        "a": "A 1309 self-aligning ball bearing has a 45 mm bore, 100 mm outer diameter and 25 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1309 bore code work?",
        "a": "The last two digits of 1309 are bore code 09, giving 09 × 5 = 45 mm bore. The 100 mm outside diameter and 25 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1309?",
        "a": "A bare 1309 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 45 mm bore?",
        "a": "The 13xx is the medium section: 100×25 mm, 27.5 mm radial section at 45 mm bore, carrying more load than a 1209 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1309-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1309-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1309K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "seal_type": "open",
    "dynamic_load_kN": 38.5,
    "static_load_kN": 12.7,
    "fatigue_load_limit_kN": 0.33,
    "limiting_speed_rpm": 6000,
    "speed_oil_rpm": 7500,
    "weight_g": 971,
    "manufacturer_designation": "1309SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1309SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1309 carries bore code 09 = 45 mm. Outside diameter 100 mm and width 25 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1309. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "electric motors and generators",
      "centrifugal pump shafts",
      "small gearbox input/output shafts",
      "conveyor roller and pulley shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "At a 45 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 1309K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 13xx medium section at 45 mm bore gains rating through a larger 100 mm OD and 25 mm width; verify the housing accepts the larger envelope before substituting for a 1209.",
      "Tapered-bore 1309K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 45 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Shaft and housing fillets must clear the bearing chamfer so the 25 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1309K self-aligning ball bearing?",
        "a": "A 1309K self-aligning ball bearing has a 45 mm bore, 100 mm outer diameter and 25 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1309."
      },
      {
        "q": "How does the 1309 bore code work?",
        "a": "The last two digits of 1309 are bore code 09, giving 09 × 5 = 45 mm bore. The 100 mm outside diameter and 25 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1309K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1309. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 45 mm bore?",
        "a": "The 13xx is the medium section: 100×25 mm, 27.5 mm radial section at 45 mm bore, carrying more load than a 1209 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1309K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2309",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 36,
    "seal_type": "open",
    "dynamic_load_kN": 55,
    "static_load_kN": 16.7,
    "fatigue_load_limit_kN": 0.71,
    "limiting_speed_rpm": 5600,
    "speed_oil_rpm": 7100,
    "weight_g": 1200,
    "manufacturer_designation": "2309S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2309S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2309 carries bore code 09 = 45 mm. Outside diameter 100 mm and width 36 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor roller and pulley shafts",
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "At a 45 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2309; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 23xx heavy wide-section at 45 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2309 has no lubricant retention: grease escapes and contaminants migrate straight into the 45×100×36 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2309 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 36 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2309 self-aligning ball bearing?",
        "a": "A 2309 self-aligning ball bearing has a 45 mm bore, 100 mm outer diameter and 36 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2309 bore code work?",
        "a": "The last two digits of 2309 are bore code 09, giving 09 × 5 = 45 mm bore. The 100 mm outside diameter and 36 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2309?",
        "a": "A bare 2309 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 45 mm bore?",
        "a": "The 23xx is the wide heavy section: 100×36 mm, 27.5 mm radial section at 45 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2309-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2309-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2309-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2309-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2309K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 36,
    "seal_type": "open",
    "dynamic_load_kN": 55,
    "static_load_kN": 16.7,
    "fatigue_load_limit_kN": 0.71,
    "limiting_speed_rpm": 5600,
    "speed_oil_rpm": 7100,
    "weight_g": 1200,
    "manufacturer_designation": "2309SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2309SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2309 carries bore code 09 = 45 mm. Outside diameter 100 mm and width 36 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2309. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "agricultural equipment (harvesters, balers)",
      "industrial fan and blower shafts",
      "electric motors and generators",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "At a 45 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 2309K; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.",
      "The 23xx heavy wide-section at 45 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2309K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 45 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2309K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2309K self-aligning ball bearing?",
        "a": "A 2309K self-aligning ball bearing has a 45 mm bore, 100 mm outer diameter and 36 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2309."
      },
      {
        "q": "How does the 2309 bore code work?",
        "a": "The last two digits of 2309 are bore code 09, giving 09 × 5 = 45 mm bore. The 100 mm outside diameter and 36 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2309K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2309. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 45 mm bore?",
        "a": "The 23xx is the wide heavy section: 100×36 mm, 27.5 mm radial section at 45 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2309K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1210",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "seal_type": "open",
    "dynamic_load_kN": 22.8,
    "static_load_kN": 8.1,
    "fatigue_load_limit_kN": 0.33,
    "limiting_speed_rpm": 6300,
    "speed_oil_rpm": 8000,
    "weight_g": 535,
    "manufacturer_designation": "1210S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1210S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1210 carries bore code 10 = 50 mm. Outside diameter 90 mm and width 20 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 50 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1210 with C3 for those conditions.",
      "The 12xx light section at 50 mm bore uses a smaller 90 mm OD than a 1310; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1210 has no lubricant retention: grease escapes and contaminants migrate straight into the 50×90×20 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1210 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1210-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1210 self-aligning ball bearing?",
        "a": "A 1210 self-aligning ball bearing has a 50 mm bore, 90 mm outer diameter and 20 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1210 bore code work?",
        "a": "The last two digits of 1210 are bore code 10, giving 10 × 5 = 50 mm bore. The 90 mm outside diameter and 20 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1210?",
        "a": "A bare 1210 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 50 mm bore?",
        "a": "The 12xx is the light section: 90×20 mm with a 20.0 mm radial section at 50 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1210-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1210-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "1210K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "seal_type": "open",
    "dynamic_load_kN": 22.8,
    "static_load_kN": 8.1,
    "fatigue_load_limit_kN": 0.33,
    "limiting_speed_rpm": 6300,
    "speed_oil_rpm": 8000,
    "weight_g": 535,
    "manufacturer_designation": "1210SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1210SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1210 carries bore code 10 = 50 mm. Outside diameter 90 mm and width 20 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1210. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 50 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1210 with C3 for those conditions.",
      "The 12xx light section at 50 mm bore uses a smaller 90 mm OD than a 1310; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1210K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 50 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Shaft and housing fillets must clear the bearing chamfer so the 20 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1210K self-aligning ball bearing?",
        "a": "A 1210K self-aligning ball bearing has a 50 mm bore, 90 mm outer diameter and 20 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1210."
      },
      {
        "q": "How does the 1210 bore code work?",
        "a": "The last two digits of 1210 are bore code 10, giving 10 × 5 = 50 mm bore. The 90 mm outside diameter and 20 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1210K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1210. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 50 mm bore?",
        "a": "The 12xx is the light section: 90×20 mm with a 20.0 mm radial section at 50 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1210K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2210",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 23,
    "seal_type": "open",
    "dynamic_load_kN": 23.3,
    "static_load_kN": 8.45,
    "fatigue_load_limit_kN": 0.57,
    "limiting_speed_rpm": 6300,
    "speed_oil_rpm": 8000,
    "weight_g": 598,
    "manufacturer_designation": "2210S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2210S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2210 carries bore code 10 = 50 mm. Outside diameter 90 mm and width 23 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 50 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2210 with C3 for those conditions.",
      "The 22xx wide-section at 50 mm bore adds load capacity through increased 23 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1210.",
      "The open 2210 has no lubricant retention: grease escapes and contaminants migrate straight into the 50×90×23 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2210 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 23 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2210 self-aligning ball bearing?",
        "a": "A 2210 self-aligning ball bearing has a 50 mm bore, 90 mm outer diameter and 23 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2210 bore code work?",
        "a": "The last two digits of 2210 are bore code 10, giving 10 × 5 = 50 mm bore. The 90 mm outside diameter and 23 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2210?",
        "a": "A bare 2210 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 50 mm bore?",
        "a": "The 22xx is the wide light section: 90×23 mm with a 20.0 mm radial section at 50 mm bore, wider than a 1210 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2210-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2210-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2210-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2210-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2210K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 23,
    "seal_type": "open",
    "dynamic_load_kN": 23.3,
    "static_load_kN": 8.45,
    "fatigue_load_limit_kN": 0.57,
    "limiting_speed_rpm": 6300,
    "speed_oil_rpm": 8000,
    "weight_g": 598,
    "manufacturer_designation": "2210SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2210SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2210 carries bore code 10 = 50 mm. Outside diameter 90 mm and width 23 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2210. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 50 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2210 with C3 for those conditions.",
      "The 22xx wide-section at 50 mm bore adds load capacity through increased 23 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1210.",
      "Tapered-bore 2210K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 50 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2210K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2210K self-aligning ball bearing?",
        "a": "A 2210K self-aligning ball bearing has a 50 mm bore, 90 mm outer diameter and 23 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2210."
      },
      {
        "q": "How does the 2210 bore code work?",
        "a": "The last two digits of 2210 are bore code 10, giving 10 × 5 = 50 mm bore. The 90 mm outside diameter and 23 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2210K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2210. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 50 mm bore?",
        "a": "The 22xx is the wide light section: 90×23 mm with a 20.0 mm radial section at 50 mm bore, wider than a 1210 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2210K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1310",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "seal_type": "open",
    "dynamic_load_kN": 43.5,
    "static_load_kN": 14.1,
    "fatigue_load_limit_kN": 0.35,
    "limiting_speed_rpm": 5600,
    "speed_oil_rpm": 6700,
    "weight_g": 1230,
    "manufacturer_designation": "1310S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1310S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1310 carries bore code 10 = 50 mm. Outside diameter 110 mm and width 27 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 50 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1310 with C3 for those conditions.",
      "The 13xx medium section at 50 mm bore gains rating through a larger 110 mm OD and 27 mm width; verify the housing accepts the larger envelope before substituting for a 1210.",
      "The open 1310 has no lubricant retention: grease escapes and contaminants migrate straight into the 50×110×27 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1310 units.",
      "A 50 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1310 self-aligning ball bearing?",
        "a": "A 1310 self-aligning ball bearing has a 50 mm bore, 110 mm outer diameter and 27 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1310 bore code work?",
        "a": "The last two digits of 1310 are bore code 10, giving 10 × 5 = 50 mm bore. The 110 mm outside diameter and 27 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1310?",
        "a": "A bare 1310 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 50 mm bore?",
        "a": "The 13xx is the medium section: 110×27 mm, 30.0 mm radial section at 50 mm bore, carrying more load than a 1210 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1310-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1310-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1310K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "seal_type": "open",
    "dynamic_load_kN": 43.5,
    "static_load_kN": 14.1,
    "fatigue_load_limit_kN": 0.35,
    "limiting_speed_rpm": 5600,
    "speed_oil_rpm": 6700,
    "weight_g": 1230,
    "manufacturer_designation": "1310SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1310SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1310 carries bore code 10 = 50 mm. Outside diameter 110 mm and width 27 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1310. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 50 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1310 with C3 for those conditions.",
      "The 13xx medium section at 50 mm bore gains rating through a larger 110 mm OD and 27 mm width; verify the housing accepts the larger envelope before substituting for a 1210.",
      "Tapered-bore 1310K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 50 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1310K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1310K self-aligning ball bearing?",
        "a": "A 1310K self-aligning ball bearing has a 50 mm bore, 110 mm outer diameter and 27 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1310."
      },
      {
        "q": "How does the 1310 bore code work?",
        "a": "The last two digits of 1310 are bore code 10, giving 10 × 5 = 50 mm bore. The 110 mm outside diameter and 27 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1310K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1310. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 50 mm bore?",
        "a": "The 13xx is the medium section: 110×27 mm, 30.0 mm radial section at 50 mm bore, carrying more load than a 1210 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1310K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2310",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 40,
    "seal_type": "open",
    "dynamic_load_kN": 65,
    "static_load_kN": 20.2,
    "fatigue_load_limit_kN": 0.86,
    "limiting_speed_rpm": 5000,
    "speed_oil_rpm": 6300,
    "weight_g": 1630,
    "manufacturer_designation": "2310S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2310S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2310 carries bore code 10 = 50 mm. Outside diameter 110 mm and width 40 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 50 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2310 with C3 for those conditions.",
      "The 23xx heavy wide-section at 50 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2310 has no lubricant retention: grease escapes and contaminants migrate straight into the 50×110×40 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2310 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 2310."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2310 self-aligning ball bearing?",
        "a": "A 2310 self-aligning ball bearing has a 50 mm bore, 110 mm outer diameter and 40 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2310 bore code work?",
        "a": "The last two digits of 2310 are bore code 10, giving 10 × 5 = 50 mm bore. The 110 mm outside diameter and 40 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2310?",
        "a": "A bare 2310 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 50 mm bore?",
        "a": "The 23xx is the wide heavy section: 110×40 mm, 30.0 mm radial section at 50 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2310-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×40 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2310-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×40 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2310-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2310K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 40,
    "seal_type": "open",
    "dynamic_load_kN": 65,
    "static_load_kN": 20.2,
    "fatigue_load_limit_kN": 0.86,
    "limiting_speed_rpm": 5000,
    "speed_oil_rpm": 6300,
    "weight_g": 1630,
    "manufacturer_designation": "2310SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2310SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2310 carries bore code 10 = 50 mm. Outside diameter 110 mm and width 40 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2310. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 50 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2310 with C3 for those conditions.",
      "The 23xx heavy wide-section at 50 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2310K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 50 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2310K self-aligning ball bearing?",
        "a": "A 2310K self-aligning ball bearing has a 50 mm bore, 110 mm outer diameter and 40 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2310."
      },
      {
        "q": "How does the 2310 bore code work?",
        "a": "The last two digits of 2310 are bore code 10, giving 10 × 5 = 50 mm bore. The 110 mm outside diameter and 40 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2310K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2310. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 50 mm bore?",
        "a": "The 23xx is the wide heavy section: 110×40 mm, 30.0 mm radial section at 50 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2310K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1211",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "seal_type": "open",
    "dynamic_load_kN": 26.9,
    "static_load_kN": 10,
    "fatigue_load_limit_kN": 0.4,
    "limiting_speed_rpm": 6000,
    "speed_oil_rpm": 7100,
    "weight_g": 708,
    "manufacturer_designation": "1211S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1211S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1211 carries bore code 11 = 55 mm. Outside diameter 100 mm and width 21 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 55 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1211 with C3 for those conditions.",
      "The 12xx light section at 55 mm bore uses a smaller 100 mm OD than a 1311; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1211 has no lubricant retention: grease escapes and contaminants migrate straight into the 55×100×21 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1211 units.",
      "A 55 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1211 self-aligning ball bearing?",
        "a": "A 1211 self-aligning ball bearing has a 55 mm bore, 100 mm outer diameter and 21 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1211 bore code work?",
        "a": "The last two digits of 1211 are bore code 11, giving 11 × 5 = 55 mm bore. The 100 mm outside diameter and 21 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1211?",
        "a": "A bare 1211 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 55 mm bore?",
        "a": "The 12xx is the light section: 100×21 mm with a 22.5 mm radial section at 55 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1211-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1211-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1211K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "seal_type": "open",
    "dynamic_load_kN": 26.9,
    "static_load_kN": 10,
    "fatigue_load_limit_kN": 0.4,
    "limiting_speed_rpm": 6000,
    "speed_oil_rpm": 7100,
    "weight_g": 708,
    "manufacturer_designation": "1211SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1211SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1211 carries bore code 11 = 55 mm. Outside diameter 100 mm and width 21 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1211. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 55 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1211 with C3 for those conditions.",
      "The 12xx light section at 55 mm bore uses a smaller 100 mm OD than a 1311; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1211K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 55 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1211K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1211K self-aligning ball bearing?",
        "a": "A 1211K self-aligning ball bearing has a 55 mm bore, 100 mm outer diameter and 21 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1211."
      },
      {
        "q": "How does the 1211 bore code work?",
        "a": "The last two digits of 1211 are bore code 11, giving 11 × 5 = 55 mm bore. The 100 mm outside diameter and 21 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1211K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1211. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 55 mm bore?",
        "a": "The 12xx is the light section: 100×21 mm with a 22.5 mm radial section at 55 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1211K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2211",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 25,
    "seal_type": "open",
    "dynamic_load_kN": 26.7,
    "static_load_kN": 9.9,
    "fatigue_load_limit_kN": 0.72,
    "limiting_speed_rpm": 6000,
    "speed_oil_rpm": 7100,
    "weight_g": 807,
    "manufacturer_designation": "2211S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2211S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2211 carries bore code 11 = 55 mm. Outside diameter 100 mm and width 25 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 55 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2211 with C3 for those conditions.",
      "The 22xx wide-section at 55 mm bore adds load capacity through increased 25 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1211.",
      "The open 2211 has no lubricant retention: grease escapes and contaminants migrate straight into the 55×100×25 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2211 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 2211."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2211 self-aligning ball bearing?",
        "a": "A 2211 self-aligning ball bearing has a 55 mm bore, 100 mm outer diameter and 25 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2211 bore code work?",
        "a": "The last two digits of 2211 are bore code 11, giving 11 × 5 = 55 mm bore. The 100 mm outside diameter and 25 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2211?",
        "a": "A bare 2211 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 55 mm bore?",
        "a": "The 22xx is the wide light section: 100×25 mm with a 22.5 mm radial section at 55 mm bore, wider than a 1211 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2211-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2211-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2211-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2211-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2211K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 25,
    "seal_type": "open",
    "dynamic_load_kN": 26.7,
    "static_load_kN": 9.9,
    "fatigue_load_limit_kN": 0.72,
    "limiting_speed_rpm": 6000,
    "speed_oil_rpm": 7100,
    "weight_g": 807,
    "manufacturer_designation": "2211SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2211SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2211 carries bore code 11 = 55 mm. Outside diameter 100 mm and width 25 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2211. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 55 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2211 with C3 for those conditions.",
      "The 22xx wide-section at 55 mm bore adds load capacity through increased 25 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1211.",
      "Tapered-bore 2211K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 55 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2211K self-aligning ball bearing?",
        "a": "A 2211K self-aligning ball bearing has a 55 mm bore, 100 mm outer diameter and 25 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2211."
      },
      {
        "q": "How does the 2211 bore code work?",
        "a": "The last two digits of 2211 are bore code 11, giving 11 × 5 = 55 mm bore. The 100 mm outside diameter and 25 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2211K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2211. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 55 mm bore?",
        "a": "The 22xx is the wide light section: 100×25 mm with a 22.5 mm radial section at 55 mm bore, wider than a 1211 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2211K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1311",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "seal_type": "open",
    "dynamic_load_kN": 51.5,
    "static_load_kN": 17.9,
    "fatigue_load_limit_kN": 0.4,
    "limiting_speed_rpm": 5000,
    "speed_oil_rpm": 6300,
    "weight_g": 1600,
    "manufacturer_designation": "1311S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1311S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1311 carries bore code 11 = 55 mm. Outside diameter 120 mm and width 29 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 55 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1311 with C3 for those conditions.",
      "The 13xx medium section at 55 mm bore gains rating through a larger 120 mm OD and 29 mm width; verify the housing accepts the larger envelope before substituting for a 1211.",
      "The open 1311 has no lubricant retention: grease escapes and contaminants migrate straight into the 55×120×29 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1311 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 29 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1311 self-aligning ball bearing?",
        "a": "A 1311 self-aligning ball bearing has a 55 mm bore, 120 mm outer diameter and 29 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1311 bore code work?",
        "a": "The last two digits of 1311 are bore code 11, giving 11 × 5 = 55 mm bore. The 120 mm outside diameter and 29 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1311?",
        "a": "A bare 1311 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 55 mm bore?",
        "a": "The 13xx is the medium section: 120×29 mm, 32.5 mm radial section at 55 mm bore, carrying more load than a 1211 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1311-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1311-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1311K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "seal_type": "open",
    "dynamic_load_kN": 51.5,
    "static_load_kN": 17.9,
    "fatigue_load_limit_kN": 0.4,
    "limiting_speed_rpm": 5000,
    "speed_oil_rpm": 6300,
    "weight_g": 1600,
    "manufacturer_designation": "1311SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1311SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1311 carries bore code 11 = 55 mm. Outside diameter 120 mm and width 29 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1311. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 55 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1311 with C3 for those conditions.",
      "The 13xx medium section at 55 mm bore gains rating through a larger 120 mm OD and 29 mm width; verify the housing accepts the larger envelope before substituting for a 1211.",
      "Tapered-bore 1311K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 55 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1311K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1311K self-aligning ball bearing?",
        "a": "A 1311K self-aligning ball bearing has a 55 mm bore, 120 mm outer diameter and 29 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1311."
      },
      {
        "q": "How does the 1311 bore code work?",
        "a": "The last two digits of 1311 are bore code 11, giving 11 × 5 = 55 mm bore. The 120 mm outside diameter and 29 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1311K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1311. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 55 mm bore?",
        "a": "The 13xx is the medium section: 120×29 mm, 32.5 mm radial section at 55 mm bore, carrying more load than a 1211 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1311K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2311",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 43,
    "seal_type": "open",
    "dynamic_load_kN": 76.5,
    "static_load_kN": 24,
    "fatigue_load_limit_kN": 1,
    "limiting_speed_rpm": 4800,
    "speed_oil_rpm": 6000,
    "weight_g": 2080,
    "manufacturer_designation": "2311S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2311S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2311 carries bore code 11 = 55 mm. Outside diameter 120 mm and width 43 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 55 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2311 with C3 for those conditions.",
      "The 23xx heavy wide-section at 55 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2311 has no lubricant retention: grease escapes and contaminants migrate straight into the 55×120×43 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2311 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2311."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2311 self-aligning ball bearing?",
        "a": "A 2311 self-aligning ball bearing has a 55 mm bore, 120 mm outer diameter and 43 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2311 bore code work?",
        "a": "The last two digits of 2311 are bore code 11, giving 11 × 5 = 55 mm bore. The 120 mm outside diameter and 43 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2311?",
        "a": "A bare 2311 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 55 mm bore?",
        "a": "The 23xx is the wide heavy section: 120×43 mm, 32.5 mm radial section at 55 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2311-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2311K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 43,
    "seal_type": "open",
    "dynamic_load_kN": 76.5,
    "static_load_kN": 24,
    "fatigue_load_limit_kN": 1,
    "limiting_speed_rpm": 4800,
    "speed_oil_rpm": 6000,
    "weight_g": 2080,
    "manufacturer_designation": "2311SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2311SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2311 carries bore code 11 = 55 mm. Outside diameter 120 mm and width 43 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2311. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 55 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2311 with C3 for those conditions.",
      "The 23xx heavy wide-section at 55 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2311K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 55 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2311-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2311K self-aligning ball bearing?",
        "a": "A 2311K self-aligning ball bearing has a 55 mm bore, 120 mm outer diameter and 43 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2311."
      },
      {
        "q": "How does the 2311 bore code work?",
        "a": "The last two digits of 2311 are bore code 11, giving 11 × 5 = 55 mm bore. The 120 mm outside diameter and 43 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2311K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2311. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 55 mm bore?",
        "a": "The 23xx is the wide heavy section: 120×43 mm, 32.5 mm radial section at 55 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2311K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1212",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "seal_type": "open",
    "dynamic_load_kN": 30.5,
    "static_load_kN": 11.5,
    "fatigue_load_limit_kN": 0.46,
    "limiting_speed_rpm": 5300,
    "speed_oil_rpm": 6300,
    "weight_g": 910,
    "manufacturer_designation": "1212S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1212S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1212 carries bore code 12 = 60 mm. Outside diameter 110 mm and width 22 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 60 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1212 with C3 for those conditions.",
      "The 12xx light section at 60 mm bore uses a smaller 110 mm OD than a 1312; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1212 has no lubricant retention: grease escapes and contaminants migrate straight into the 60×110×22 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1212 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 22 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1212 self-aligning ball bearing?",
        "a": "A 1212 self-aligning ball bearing has a 60 mm bore, 110 mm outer diameter and 22 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1212 bore code work?",
        "a": "The last two digits of 1212 are bore code 12, giving 12 × 5 = 60 mm bore. The 110 mm outside diameter and 22 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1212?",
        "a": "A bare 1212 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 60 mm bore?",
        "a": "The 12xx is the light section: 110×22 mm with a 25.0 mm radial section at 60 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1212-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1212-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1212K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "seal_type": "open",
    "dynamic_load_kN": 30.5,
    "static_load_kN": 11.5,
    "fatigue_load_limit_kN": 0.46,
    "limiting_speed_rpm": 5300,
    "speed_oil_rpm": 6300,
    "weight_g": 910,
    "manufacturer_designation": "1212SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1212SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1212 carries bore code 12 = 60 mm. Outside diameter 110 mm and width 22 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1212. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 60 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1212 with C3 for those conditions.",
      "The 12xx light section at 60 mm bore uses a smaller 110 mm OD than a 1312; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1212K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 60 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1212K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1212K self-aligning ball bearing?",
        "a": "A 1212K self-aligning ball bearing has a 60 mm bore, 110 mm outer diameter and 22 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1212."
      },
      {
        "q": "How does the 1212 bore code work?",
        "a": "The last two digits of 1212 are bore code 12, giving 12 × 5 = 60 mm bore. The 110 mm outside diameter and 22 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1212K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1212. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 60 mm bore?",
        "a": "The 12xx is the light section: 110×22 mm with a 25.0 mm radial section at 60 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1212K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2212",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 28,
    "seal_type": "open",
    "dynamic_load_kN": 34,
    "static_load_kN": 12.6,
    "fatigue_load_limit_kN": 0.84,
    "limiting_speed_rpm": 5300,
    "speed_oil_rpm": 6300,
    "weight_g": 1100,
    "manufacturer_designation": "2212S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2212S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2212 carries bore code 12 = 60 mm. Outside diameter 110 mm and width 28 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 60 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2212 with C3 for those conditions.",
      "The 22xx wide-section at 60 mm bore adds load capacity through increased 28 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1212.",
      "The open 2212 has no lubricant retention: grease escapes and contaminants migrate straight into the 60×110×28 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2212 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2212."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2212 self-aligning ball bearing?",
        "a": "A 2212 self-aligning ball bearing has a 60 mm bore, 110 mm outer diameter and 28 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2212 bore code work?",
        "a": "The last two digits of 2212 are bore code 12, giving 12 × 5 = 60 mm bore. The 110 mm outside diameter and 28 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2212?",
        "a": "A bare 2212 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 60 mm bore?",
        "a": "The 22xx is the wide light section: 110×28 mm with a 25.0 mm radial section at 60 mm bore, wider than a 1212 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2212-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2212-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope per ISO 15; seal variant differs (OPEN vs 2RS) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2212-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2212-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2212K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 28,
    "seal_type": "open",
    "dynamic_load_kN": 34,
    "static_load_kN": 12.6,
    "fatigue_load_limit_kN": 0.84,
    "limiting_speed_rpm": 5300,
    "speed_oil_rpm": 6300,
    "weight_g": 1100,
    "manufacturer_designation": "2212SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2212SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2212 carries bore code 12 = 60 mm. Outside diameter 110 mm and width 28 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2212. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 60 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2212 with C3 for those conditions.",
      "The 22xx wide-section at 60 mm bore adds load capacity through increased 28 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1212.",
      "Tapered-bore 2212K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 60 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2212-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2212K self-aligning ball bearing?",
        "a": "A 2212K self-aligning ball bearing has a 60 mm bore, 110 mm outer diameter and 28 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2212."
      },
      {
        "q": "How does the 2212 bore code work?",
        "a": "The last two digits of 2212 are bore code 12, giving 12 × 5 = 60 mm bore. The 110 mm outside diameter and 28 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2212K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2212. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 60 mm bore?",
        "a": "The 22xx is the wide light section: 110×28 mm with a 25.0 mm radial section at 60 mm bore, wider than a 1212 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2212K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1312",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "seal_type": "open",
    "dynamic_load_kN": 57.5,
    "static_load_kN": 20.8,
    "fatigue_load_limit_kN": 0.51,
    "limiting_speed_rpm": 4500,
    "speed_oil_rpm": 5600,
    "weight_g": 2000,
    "manufacturer_designation": "1312S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1312S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1312 carries bore code 12 = 60 mm. Outside diameter 130 mm and width 31 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 60 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1312 with C3 for those conditions.",
      "The 13xx medium section at 60 mm bore gains rating through a larger 130 mm OD and 31 mm width; verify the housing accepts the larger envelope before substituting for a 1212.",
      "The open 1312 has no lubricant retention: grease escapes and contaminants migrate straight into the 60×130×31 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1312 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1312."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1312 self-aligning ball bearing?",
        "a": "A 1312 self-aligning ball bearing has a 60 mm bore, 130 mm outer diameter and 31 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1312 bore code work?",
        "a": "The last two digits of 1312 are bore code 12, giving 12 × 5 = 60 mm bore. The 130 mm outside diameter and 31 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1312?",
        "a": "A bare 1312 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 60 mm bore?",
        "a": "The 13xx is the medium section: 130×31 mm, 35.0 mm radial section at 60 mm bore, carrying more load than a 1212 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1312-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1312-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1312K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "seal_type": "open",
    "dynamic_load_kN": 57.5,
    "static_load_kN": 20.8,
    "fatigue_load_limit_kN": 0.51,
    "limiting_speed_rpm": 4500,
    "speed_oil_rpm": 5600,
    "weight_g": 2000,
    "manufacturer_designation": "1312SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1312SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1312 carries bore code 12 = 60 mm. Outside diameter 130 mm and width 31 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1312. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 60 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1312 with C3 for those conditions.",
      "The 13xx medium section at 60 mm bore gains rating through a larger 130 mm OD and 31 mm width; verify the housing accepts the larger envelope before substituting for a 1212.",
      "Tapered-bore 1312K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 60 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1312K self-aligning ball bearing?",
        "a": "A 1312K self-aligning ball bearing has a 60 mm bore, 130 mm outer diameter and 31 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1312."
      },
      {
        "q": "How does the 1312 bore code work?",
        "a": "The last two digits of 1312 are bore code 12, giving 12 × 5 = 60 mm bore. The 130 mm outside diameter and 31 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1312K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1312. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 60 mm bore?",
        "a": "The 13xx is the medium section: 130×31 mm, 35.0 mm radial section at 60 mm bore, carrying more load than a 1212 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1312K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2312",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 46,
    "seal_type": "open",
    "dynamic_load_kN": 88.5,
    "static_load_kN": 28.3,
    "fatigue_load_limit_kN": 1.2,
    "limiting_speed_rpm": 4300,
    "speed_oil_rpm": 5300,
    "weight_g": 2580,
    "manufacturer_designation": "2312S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2312S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2312 carries bore code 12 = 60 mm. Outside diameter 130 mm and width 46 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 60 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2312 with C3 for those conditions.",
      "The 23xx heavy wide-section at 60 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2312 has no lubricant retention: grease escapes and contaminants migrate straight into the 60×130×46 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2312 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2312 self-aligning ball bearing?",
        "a": "A 2312 self-aligning ball bearing has a 60 mm bore, 130 mm outer diameter and 46 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2312 bore code work?",
        "a": "The last two digits of 2312 are bore code 12, giving 12 × 5 = 60 mm bore. The 130 mm outside diameter and 46 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2312?",
        "a": "A bare 2312 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 60 mm bore?",
        "a": "The 23xx is the wide heavy section: 130×46 mm, 35.0 mm radial section at 60 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2312-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2312K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 46,
    "seal_type": "open",
    "dynamic_load_kN": 88.5,
    "static_load_kN": 28.3,
    "fatigue_load_limit_kN": 1.2,
    "limiting_speed_rpm": 4300,
    "speed_oil_rpm": 5300,
    "weight_g": 2580,
    "manufacturer_designation": "2312SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2312SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2312 carries bore code 12 = 60 mm. Outside diameter 130 mm and width 46 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2312. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 60 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2312 with C3 for those conditions.",
      "The 23xx heavy wide-section at 60 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2312K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 60 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "A 60 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2312K self-aligning ball bearing?",
        "a": "A 2312K self-aligning ball bearing has a 60 mm bore, 130 mm outer diameter and 46 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2312."
      },
      {
        "q": "How does the 2312 bore code work?",
        "a": "The last two digits of 2312 are bore code 12, giving 12 × 5 = 60 mm bore. The 130 mm outside diameter and 46 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2312K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2312. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 60 mm bore?",
        "a": "The 23xx is the wide heavy section: 130×46 mm, 35.0 mm radial section at 60 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2312K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1213",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "seal_type": "open",
    "dynamic_load_kN": 31,
    "static_load_kN": 12.5,
    "fatigue_load_limit_kN": 0.5,
    "limiting_speed_rpm": 4800,
    "speed_oil_rpm": 6000,
    "weight_g": 1160,
    "manufacturer_designation": "1213S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1213S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1213 carries bore code 13 = 65 mm. Outside diameter 120 mm and width 23 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 65 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1213 with C3 for those conditions.",
      "The 12xx light section at 65 mm bore uses a smaller 120 mm OD than a 1313; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1213 has no lubricant retention: grease escapes and contaminants migrate straight into the 65×120×23 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1213 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1213."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1213 self-aligning ball bearing?",
        "a": "A 1213 self-aligning ball bearing has a 65 mm bore, 120 mm outer diameter and 23 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1213 bore code work?",
        "a": "The last two digits of 1213 are bore code 13, giving 13 × 5 = 65 mm bore. The 120 mm outside diameter and 23 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1213?",
        "a": "A bare 1213 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 65 mm bore?",
        "a": "The 12xx is the light section: 120×23 mm with a 27.5 mm radial section at 65 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1213-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1213-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "1213K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "seal_type": "open",
    "dynamic_load_kN": 31,
    "static_load_kN": 12.5,
    "fatigue_load_limit_kN": 0.5,
    "limiting_speed_rpm": 4800,
    "speed_oil_rpm": 6000,
    "weight_g": 1160,
    "manufacturer_designation": "1213SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1213SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1213 carries bore code 13 = 65 mm. Outside diameter 120 mm and width 23 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1213. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 65 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1213 with C3 for those conditions.",
      "The 12xx light section at 65 mm bore uses a smaller 120 mm OD than a 1313; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1213K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 65 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1213K self-aligning ball bearing?",
        "a": "A 1213K self-aligning ball bearing has a 65 mm bore, 120 mm outer diameter and 23 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1213."
      },
      {
        "q": "How does the 1213 bore code work?",
        "a": "The last two digits of 1213 are bore code 13, giving 13 × 5 = 65 mm bore. The 120 mm outside diameter and 23 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1213K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1213. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 65 mm bore?",
        "a": "The 12xx is the light section: 120×23 mm with a 27.5 mm radial section at 65 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1213K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2213",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 31,
    "seal_type": "open",
    "dynamic_load_kN": 43.5,
    "static_load_kN": 16.4,
    "fatigue_load_limit_kN": 0.92,
    "limiting_speed_rpm": 4800,
    "speed_oil_rpm": 6000,
    "weight_g": 1500,
    "manufacturer_designation": "2213S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2213S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2213 carries bore code 13 = 65 mm. Outside diameter 120 mm and width 31 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 65 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2213 with C3 for those conditions.",
      "The 22xx wide-section at 65 mm bore adds load capacity through increased 31 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1213.",
      "The open 2213 has no lubricant retention: grease escapes and contaminants migrate straight into the 65×120×31 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2213 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2213 self-aligning ball bearing?",
        "a": "A 2213 self-aligning ball bearing has a 65 mm bore, 120 mm outer diameter and 31 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2213 bore code work?",
        "a": "The last two digits of 2213 are bore code 13, giving 13 × 5 = 65 mm bore. The 120 mm outside diameter and 31 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2213?",
        "a": "A bare 2213 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 65 mm bore?",
        "a": "The 22xx is the wide light section: 120×31 mm with a 27.5 mm radial section at 65 mm bore, wider than a 1213 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2213-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2213-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2213-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2213-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2213K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 31,
    "seal_type": "open",
    "dynamic_load_kN": 43.5,
    "static_load_kN": 16.4,
    "fatigue_load_limit_kN": 0.92,
    "limiting_speed_rpm": 4800,
    "speed_oil_rpm": 6000,
    "weight_g": 1500,
    "manufacturer_designation": "2213SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2213SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2213 carries bore code 13 = 65 mm. Outside diameter 120 mm and width 31 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2213. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 65 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2213 with C3 for those conditions.",
      "The 22xx wide-section at 65 mm bore adds load capacity through increased 31 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1213.",
      "Tapered-bore 2213K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 65 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "A 65 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2213K self-aligning ball bearing?",
        "a": "A 2213K self-aligning ball bearing has a 65 mm bore, 120 mm outer diameter and 31 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2213."
      },
      {
        "q": "How does the 2213 bore code work?",
        "a": "The last two digits of 2213 are bore code 13, giving 13 × 5 = 65 mm bore. The 120 mm outside diameter and 31 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2213K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2213. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 65 mm bore?",
        "a": "The 22xx is the wide light section: 120×31 mm with a 27.5 mm radial section at 65 mm bore, wider than a 1213 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2213K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1313",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "seal_type": "open",
    "dynamic_load_kN": 62.5,
    "static_load_kN": 22.9,
    "fatigue_load_limit_kN": 0.67,
    "limiting_speed_rpm": 4300,
    "speed_oil_rpm": 5300,
    "weight_g": 2470,
    "manufacturer_designation": "1313S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1313S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1313 carries bore code 13 = 65 mm. Outside diameter 140 mm and width 33 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 65 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1313 with C3 for those conditions.",
      "The 13xx medium section at 65 mm bore gains rating through a larger 140 mm OD and 33 mm width; verify the housing accepts the larger envelope before substituting for a 1213.",
      "The open 1313 has no lubricant retention: grease escapes and contaminants migrate straight into the 65×140×33 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1313 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1313."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1313 self-aligning ball bearing?",
        "a": "A 1313 self-aligning ball bearing has a 65 mm bore, 140 mm outer diameter and 33 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1313 bore code work?",
        "a": "The last two digits of 1313 are bore code 13, giving 13 × 5 = 65 mm bore. The 140 mm outside diameter and 33 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1313?",
        "a": "A bare 1313 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 65 mm bore?",
        "a": "The 13xx is the medium section: 140×33 mm, 37.5 mm radial section at 65 mm bore, carrying more load than a 1213 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1313-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1313-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "1313K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "seal_type": "open",
    "dynamic_load_kN": 62.5,
    "static_load_kN": 22.9,
    "fatigue_load_limit_kN": 0.67,
    "limiting_speed_rpm": 4300,
    "speed_oil_rpm": 5300,
    "weight_g": 2470,
    "manufacturer_designation": "1313SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1313SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1313 carries bore code 13 = 65 mm. Outside diameter 140 mm and width 33 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1313. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 65 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1313 with C3 for those conditions.",
      "The 13xx medium section at 65 mm bore gains rating through a larger 140 mm OD and 33 mm width; verify the housing accepts the larger envelope before substituting for a 1213.",
      "Tapered-bore 1313K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 65 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1313-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1313K self-aligning ball bearing?",
        "a": "A 1313K self-aligning ball bearing has a 65 mm bore, 140 mm outer diameter and 33 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1313."
      },
      {
        "q": "How does the 1313 bore code work?",
        "a": "The last two digits of 1313 are bore code 13, giving 13 × 5 = 65 mm bore. The 140 mm outside diameter and 33 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1313K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1313. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 65 mm bore?",
        "a": "The 13xx is the medium section: 140×33 mm, 37.5 mm radial section at 65 mm bore, carrying more load than a 1213 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1313K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2313",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 48,
    "seal_type": "open",
    "dynamic_load_kN": 97,
    "static_load_kN": 32.5,
    "fatigue_load_limit_kN": 1.4,
    "limiting_speed_rpm": 3800,
    "speed_oil_rpm": 4800,
    "weight_g": 3200,
    "manufacturer_designation": "2313S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2313S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2313 carries bore code 13 = 65 mm. Outside diameter 140 mm and width 48 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 65 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2313 with C3 for those conditions.",
      "The 23xx heavy wide-section at 65 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2313 has no lubricant retention: grease escapes and contaminants migrate straight into the 65×140×48 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2313 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2313-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2313 self-aligning ball bearing?",
        "a": "A 2313 self-aligning ball bearing has a 65 mm bore, 140 mm outer diameter and 48 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2313 bore code work?",
        "a": "The last two digits of 2313 are bore code 13, giving 13 × 5 = 65 mm bore. The 140 mm outside diameter and 48 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2313?",
        "a": "A bare 2313 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 65 mm bore?",
        "a": "The 23xx is the wide heavy section: 140×48 mm, 37.5 mm radial section at 65 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2313-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2313K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 48,
    "seal_type": "open",
    "dynamic_load_kN": 97,
    "static_load_kN": 32.5,
    "fatigue_load_limit_kN": 1.4,
    "limiting_speed_rpm": 3800,
    "speed_oil_rpm": 4800,
    "weight_g": 3200,
    "manufacturer_designation": "2313SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2313SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2313 carries bore code 13 = 65 mm. Outside diameter 140 mm and width 48 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2313. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 65 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2313 with C3 for those conditions.",
      "The 23xx heavy wide-section at 65 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2313K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 65 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Shaft and housing fillets must clear the bearing chamfer so the 48 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2313K self-aligning ball bearing?",
        "a": "A 2313K self-aligning ball bearing has a 65 mm bore, 140 mm outer diameter and 48 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2313."
      },
      {
        "q": "How does the 2313 bore code work?",
        "a": "The last two digits of 2313 are bore code 13, giving 13 × 5 = 65 mm bore. The 140 mm outside diameter and 48 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2313K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2313. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 65 mm bore?",
        "a": "The 23xx is the wide heavy section: 140×48 mm, 37.5 mm radial section at 65 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2313K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1214",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "seal_type": "open",
    "dynamic_load_kN": 35,
    "static_load_kN": 13.8,
    "fatigue_load_limit_kN": 0.55,
    "limiting_speed_rpm": 4800,
    "speed_oil_rpm": 5600,
    "weight_g": 1300,
    "manufacturer_designation": "1214S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1214S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1214 carries bore code 14 = 70 mm. Outside diameter 125 mm and width 24 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 70 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1214 with C3 for those conditions.",
      "The 12xx light section at 70 mm bore uses a smaller 125 mm OD than a 1314; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1214 has no lubricant retention: grease escapes and contaminants migrate straight into the 70×125×24 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1214 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1214."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1214 self-aligning ball bearing?",
        "a": "A 1214 self-aligning ball bearing has a 70 mm bore, 125 mm outer diameter and 24 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1214 bore code work?",
        "a": "The last two digits of 1214 are bore code 14, giving 14 × 5 = 70 mm bore. The 125 mm outside diameter and 24 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1214?",
        "a": "A bare 1214 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 70 mm bore?",
        "a": "The 12xx is the light section: 125×24 mm with a 27.5 mm radial section at 70 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1214-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2214",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 31,
    "seal_type": "open",
    "dynamic_load_kN": 44,
    "static_load_kN": 17.1,
    "fatigue_load_limit_kN": 1.1,
    "limiting_speed_rpm": 4500,
    "speed_oil_rpm": 5600,
    "weight_g": 1550,
    "manufacturer_designation": "2214S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2214S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2214 carries bore code 14 = 70 mm. Outside diameter 125 mm and width 31 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 70 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2214 with C3 for those conditions.",
      "The 22xx wide-section at 70 mm bore adds load capacity through increased 31 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1214.",
      "The open 2214 has no lubricant retention: grease escapes and contaminants migrate straight into the 70×125×31 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2214 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2214-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2214 self-aligning ball bearing?",
        "a": "A 2214 self-aligning ball bearing has a 70 mm bore, 125 mm outer diameter and 31 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2214 bore code work?",
        "a": "The last two digits of 2214 are bore code 14, giving 14 × 5 = 70 mm bore. The 125 mm outside diameter and 31 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2214?",
        "a": "A bare 2214 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 70 mm bore?",
        "a": "The 22xx is the wide light section: 125×31 mm with a 27.5 mm radial section at 70 mm bore, wider than a 1214 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2214-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×31 mm envelope per ISO 15; seal variant (OPEN vs 2RS) and load ratings differ — confirm sealing and rating before substituting."
      }
    ]
  },
  {
    "sku": "1314",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "seal_type": "open",
    "dynamic_load_kN": 75,
    "static_load_kN": 27.7,
    "fatigue_load_limit_kN": 0.69,
    "limiting_speed_rpm": 4000,
    "speed_oil_rpm": 5000,
    "weight_g": 3030,
    "manufacturer_designation": "1314S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1314S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1314 carries bore code 14 = 70 mm. Outside diameter 150 mm and width 35 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 70 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1314 with C3 for those conditions.",
      "The 13xx medium section at 70 mm bore gains rating through a larger 150 mm OD and 35 mm width; verify the housing accepts the larger envelope before substituting for a 1214.",
      "The open 1314 has no lubricant retention: grease escapes and contaminants migrate straight into the 70×150×35 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1314 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1314 self-aligning ball bearing?",
        "a": "A 1314 self-aligning ball bearing has a 70 mm bore, 150 mm outer diameter and 35 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1314 bore code work?",
        "a": "The last two digits of 1314 are bore code 14, giving 14 × 5 = 70 mm bore. The 150 mm outside diameter and 35 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1314?",
        "a": "A bare 1314 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 70 mm bore?",
        "a": "The 13xx is the medium section: 150×35 mm, 40.0 mm radial section at 70 mm bore, carrying more load than a 1214 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1314",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2314",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 51,
    "seal_type": "open",
    "dynamic_load_kN": 111,
    "static_load_kN": 37.5,
    "fatigue_load_limit_kN": 1.6,
    "limiting_speed_rpm": 3600,
    "speed_oil_rpm": 4500,
    "weight_g": 3900,
    "manufacturer_designation": "2314S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2314S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2314 carries bore code 14 = 70 mm. Outside diameter 150 mm and width 51 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 70 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2314 with C3 for those conditions.",
      "The 23xx heavy wide-section at 70 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2314 has no lubricant retention: grease escapes and contaminants migrate straight into the 70×150×51 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2314 units.",
      "A 70 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2314 self-aligning ball bearing?",
        "a": "A 2314 self-aligning ball bearing has a 70 mm bore, 150 mm outer diameter and 51 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2314 bore code work?",
        "a": "The last two digits of 2314 are bore code 14, giving 14 × 5 = 70 mm bore. The 150 mm outside diameter and 51 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2314?",
        "a": "A bare 2314 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 70 mm bore?",
        "a": "The 23xx is the wide heavy section: 150×51 mm, 40.0 mm radial section at 70 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2314",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1215",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "seal_type": "open",
    "dynamic_load_kN": 39,
    "static_load_kN": 15.7,
    "fatigue_load_limit_kN": 0.63,
    "limiting_speed_rpm": 4300,
    "speed_oil_rpm": 5300,
    "weight_g": 1360,
    "manufacturer_designation": "1215S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1215S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1215 carries bore code 15 = 75 mm. Outside diameter 130 mm and width 25 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 75 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1215 with C3 for those conditions.",
      "The 12xx light section at 75 mm bore uses a smaller 130 mm OD than a 1315; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1215 has no lubricant retention: grease escapes and contaminants migrate straight into the 75×130×25 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1215 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1215 self-aligning ball bearing?",
        "a": "A 1215 self-aligning ball bearing has a 75 mm bore, 130 mm outer diameter and 25 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1215 bore code work?",
        "a": "The last two digits of 1215 are bore code 15, giving 15 × 5 = 75 mm bore. The 130 mm outside diameter and 25 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1215?",
        "a": "A bare 1215 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 75 mm bore?",
        "a": "The 12xx is the light section: 130×25 mm with a 27.5 mm radial section at 75 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1215-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1215K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "seal_type": "open",
    "dynamic_load_kN": 39,
    "static_load_kN": 15.7,
    "fatigue_load_limit_kN": 0.63,
    "limiting_speed_rpm": 4300,
    "speed_oil_rpm": 5300,
    "weight_g": 1360,
    "manufacturer_designation": "1215SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1215SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1215 carries bore code 15 = 75 mm. Outside diameter 130 mm and width 25 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1215. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 75 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1215 with C3 for those conditions.",
      "The 12xx light section at 75 mm bore uses a smaller 130 mm OD than a 1315; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1215K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 75 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "A 75 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1215K self-aligning ball bearing?",
        "a": "A 1215K self-aligning ball bearing has a 75 mm bore, 130 mm outer diameter and 25 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1215."
      },
      {
        "q": "How does the 1215 bore code work?",
        "a": "The last two digits of 1215 are bore code 15, giving 15 × 5 = 75 mm bore. The 130 mm outside diameter and 25 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1215K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1215. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 75 mm bore?",
        "a": "The 12xx is the light section: 130×25 mm with a 27.5 mm radial section at 75 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1215K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2215",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 31,
    "seal_type": "open",
    "dynamic_load_kN": 44.5,
    "static_load_kN": 17.8,
    "fatigue_load_limit_kN": 1.2,
    "limiting_speed_rpm": 4300,
    "speed_oil_rpm": 5300,
    "weight_g": 1600,
    "manufacturer_designation": "2215S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2215S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2215 carries bore code 15 = 75 mm. Outside diameter 130 mm and width 31 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 75 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2215 with C3 for those conditions.",
      "The 22xx wide-section at 75 mm bore adds load capacity through increased 31 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1215.",
      "The open 2215 has no lubricant retention: grease escapes and contaminants migrate straight into the 75×130×31 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2215 units.",
      "A 75 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2215 self-aligning ball bearing?",
        "a": "A 2215 self-aligning ball bearing has a 75 mm bore, 130 mm outer diameter and 31 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2215 bore code work?",
        "a": "The last two digits of 2215 are bore code 15, giving 15 × 5 = 75 mm bore. The 130 mm outside diameter and 31 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2215?",
        "a": "A bare 2215 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 75 mm bore?",
        "a": "The 22xx is the wide light section: 130×31 mm with a 27.5 mm radial section at 75 mm bore, wider than a 1215 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2215-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2215-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2215K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 31,
    "seal_type": "open",
    "dynamic_load_kN": 44.5,
    "static_load_kN": 17.8,
    "fatigue_load_limit_kN": 1.2,
    "limiting_speed_rpm": 4300,
    "speed_oil_rpm": 5300,
    "weight_g": 1600,
    "manufacturer_designation": "2215SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2215SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2215 carries bore code 15 = 75 mm. Outside diameter 130 mm and width 31 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2215. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 75 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2215 with C3 for those conditions.",
      "The 22xx wide-section at 75 mm bore adds load capacity through increased 31 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1215.",
      "Tapered-bore 2215K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 75 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 2215K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2215K self-aligning ball bearing?",
        "a": "A 2215K self-aligning ball bearing has a 75 mm bore, 130 mm outer diameter and 31 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2215."
      },
      {
        "q": "How does the 2215 bore code work?",
        "a": "The last two digits of 2215 are bore code 15, giving 15 × 5 = 75 mm bore. The 130 mm outside diameter and 31 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2215K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2215. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 75 mm bore?",
        "a": "The 22xx is the wide light section: 130×31 mm with a 27.5 mm radial section at 75 mm bore, wider than a 1215 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2215K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1315",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "seal_type": "open",
    "dynamic_load_kN": 80,
    "static_load_kN": 30,
    "fatigue_load_limit_kN": 0.72,
    "limiting_speed_rpm": 3800,
    "speed_oil_rpm": 4500,
    "weight_g": 3630,
    "manufacturer_designation": "1315S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1315S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1315 carries bore code 15 = 75 mm. Outside diameter 160 mm and width 37 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 75 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1315 with C3 for those conditions.",
      "The 13xx medium section at 75 mm bore gains rating through a larger 160 mm OD and 37 mm width; verify the housing accepts the larger envelope before substituting for a 1215.",
      "The open 1315 has no lubricant retention: grease escapes and contaminants migrate straight into the 75×160×37 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1315 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1315-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1315 self-aligning ball bearing?",
        "a": "A 1315 self-aligning ball bearing has a 75 mm bore, 160 mm outer diameter and 37 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1315 bore code work?",
        "a": "The last two digits of 1315 are bore code 15, giving 15 × 5 = 75 mm bore. The 160 mm outside diameter and 37 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1315?",
        "a": "A bare 1315 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 75 mm bore?",
        "a": "The 13xx is the medium section: 160×37 mm, 42.5 mm radial section at 75 mm bore, carrying more load than a 1215 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1315-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1315K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "seal_type": "open",
    "dynamic_load_kN": 80,
    "static_load_kN": 30,
    "fatigue_load_limit_kN": 0.72,
    "limiting_speed_rpm": 3800,
    "speed_oil_rpm": 4500,
    "weight_g": 3630,
    "manufacturer_designation": "1315SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1315SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1315 carries bore code 15 = 75 mm. Outside diameter 160 mm and width 37 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1315. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial electric motor shafts",
      "pump and compressor drive shafts",
      "gearbox and speed reducer shafts",
      "conveyor and material handling drives"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 75 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 1315 with C3 for those conditions.",
      "The 13xx medium section at 75 mm bore gains rating through a larger 160 mm OD and 37 mm width; verify the housing accepts the larger envelope before substituting for a 1215.",
      "Tapered-bore 1315K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 75 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Shaft and housing fillets must clear the bearing chamfer so the 37 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1315K self-aligning ball bearing?",
        "a": "A 1315K self-aligning ball bearing has a 75 mm bore, 160 mm outer diameter and 37 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1315."
      },
      {
        "q": "How does the 1315 bore code work?",
        "a": "The last two digits of 1315 are bore code 15, giving 15 × 5 = 75 mm bore. The 160 mm outside diameter and 37 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1315K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1315. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 75 mm bore?",
        "a": "The 13xx is the medium section: 160×37 mm, 42.5 mm radial section at 75 mm bore, carrying more load than a 1215 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1315K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2315",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 55,
    "seal_type": "open",
    "dynamic_load_kN": 125,
    "static_load_kN": 43,
    "fatigue_load_limit_kN": 1.8,
    "limiting_speed_rpm": 3400,
    "speed_oil_rpm": 4300,
    "weight_g": 4780,
    "manufacturer_designation": "2315S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2315S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2315 carries bore code 15 = 75 mm. Outside diameter 160 mm and width 55 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "conveyor and material handling drives",
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 75 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2315 with C3 for those conditions.",
      "The 23xx heavy wide-section at 75 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2315 has no lubricant retention: grease escapes and contaminants migrate straight into the 75×160×55 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2315 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 55 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2315 self-aligning ball bearing?",
        "a": "A 2315 self-aligning ball bearing has a 75 mm bore, 160 mm outer diameter and 55 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2315 bore code work?",
        "a": "The last two digits of 2315 are bore code 15, giving 15 × 5 = 75 mm bore. The 160 mm outside diameter and 55 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2315?",
        "a": "A bare 2315 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 75 mm bore?",
        "a": "The 23xx is the wide heavy section: 160×55 mm, 42.5 mm radial section at 75 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2315-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2315K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 55,
    "seal_type": "open",
    "dynamic_load_kN": 125,
    "static_load_kN": 43,
    "fatigue_load_limit_kN": 1.8,
    "limiting_speed_rpm": 3400,
    "speed_oil_rpm": 4300,
    "weight_g": 4780,
    "manufacturer_designation": "2315SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2315SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2315 carries bore code 15 = 75 mm. Outside diameter 160 mm and width 55 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2315. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "textile and printing machine spindles",
      "paper mill and processing equipment shafts",
      "industrial electric motor shafts",
      "pump and compressor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Temperature rise and interference fits consume internal clearance on this 75 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2315 with C3 for those conditions.",
      "The 23xx heavy wide-section at 75 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2315K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 75 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2315K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2315K self-aligning ball bearing?",
        "a": "A 2315K self-aligning ball bearing has a 75 mm bore, 160 mm outer diameter and 55 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2315."
      },
      {
        "q": "How does the 2315 bore code work?",
        "a": "The last two digits of 2315 are bore code 15, giving 15 × 5 = 75 mm bore. The 160 mm outside diameter and 55 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2315K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2315. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 75 mm bore?",
        "a": "The 23xx is the wide heavy section: 160×55 mm, 42.5 mm radial section at 75 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2315K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1216",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "seal_type": "open",
    "dynamic_load_kN": 40,
    "static_load_kN": 17,
    "fatigue_load_limit_kN": 0.68,
    "limiting_speed_rpm": 4000,
    "speed_oil_rpm": 5000,
    "weight_g": 1680,
    "manufacturer_designation": "1216S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1216S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1216 carries bore code 16 = 80 mm. Outside diameter 140 mm and width 26 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Mount this 80 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 80 mm bore uses a smaller 140 mm OD than a 1316; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1216 has no lubricant retention: grease escapes and contaminants migrate straight into the 80×140×26 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1216 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1216-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1216 self-aligning ball bearing?",
        "a": "A 1216 self-aligning ball bearing has a 80 mm bore, 140 mm outer diameter and 26 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1216 bore code work?",
        "a": "The last two digits of 1216 are bore code 16, giving 16 × 5 = 80 mm bore. The 140 mm outside diameter and 26 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1216?",
        "a": "A bare 1216 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 80 mm bore?",
        "a": "The 12xx is the light section: 140×26 mm with a 30.0 mm radial section at 80 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1216-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1216K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "seal_type": "open",
    "dynamic_load_kN": 40,
    "static_load_kN": 17,
    "fatigue_load_limit_kN": 0.68,
    "limiting_speed_rpm": 4000,
    "speed_oil_rpm": 5000,
    "weight_g": 1680,
    "manufacturer_designation": "1216SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1216SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1216 carries bore code 16 = 80 mm. Outside diameter 140 mm and width 26 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1216. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Mount this 80 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 80 mm bore uses a smaller 140 mm OD than a 1316; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1216K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 80 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Shaft and housing fillets must clear the bearing chamfer so the 26 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1216K self-aligning ball bearing?",
        "a": "A 1216K self-aligning ball bearing has a 80 mm bore, 140 mm outer diameter and 26 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1216."
      },
      {
        "q": "How does the 1216 bore code work?",
        "a": "The last two digits of 1216 are bore code 16, giving 16 × 5 = 80 mm bore. The 140 mm outside diameter and 26 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1216K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1216. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 80 mm bore?",
        "a": "The 12xx is the light section: 140×26 mm with a 30.0 mm radial section at 80 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1216K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2216",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 33,
    "seal_type": "open",
    "dynamic_load_kN": 49,
    "static_load_kN": 19.9,
    "fatigue_load_limit_kN": 1.3,
    "limiting_speed_rpm": 4000,
    "speed_oil_rpm": 5000,
    "weight_g": 2020,
    "manufacturer_designation": "2216S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2216S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2216 carries bore code 16 = 80 mm. Outside diameter 140 mm and width 33 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Mount this 80 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 80 mm bore adds load capacity through increased 33 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1216.",
      "The open 2216 has no lubricant retention: grease escapes and contaminants migrate straight into the 80×140×33 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2216 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 33 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2216 self-aligning ball bearing?",
        "a": "A 2216 self-aligning ball bearing has a 80 mm bore, 140 mm outer diameter and 33 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2216 bore code work?",
        "a": "The last two digits of 2216 are bore code 16, giving 16 × 5 = 80 mm bore. The 140 mm outside diameter and 33 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2216?",
        "a": "A bare 2216 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 80 mm bore?",
        "a": "The 22xx is the wide light section: 140×33 mm with a 30.0 mm radial section at 80 mm bore, wider than a 1216 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2216-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2216-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ]
  },
  {
    "sku": "2216K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 33,
    "seal_type": "open",
    "dynamic_load_kN": 49,
    "static_load_kN": 19.9,
    "fatigue_load_limit_kN": 1.3,
    "limiting_speed_rpm": 4000,
    "speed_oil_rpm": 5000,
    "weight_g": 2020,
    "manufacturer_designation": "2216SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2216SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2216 carries bore code 16 = 80 mm. Outside diameter 140 mm and width 33 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2216. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Mount this 80 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 80 mm bore adds load capacity through increased 33 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1216.",
      "Tapered-bore 2216K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 80 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2216K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2216K self-aligning ball bearing?",
        "a": "A 2216K self-aligning ball bearing has a 80 mm bore, 140 mm outer diameter and 33 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2216."
      },
      {
        "q": "How does the 2216 bore code work?",
        "a": "The last two digits of 2216 are bore code 16, giving 16 × 5 = 80 mm bore. The 140 mm outside diameter and 33 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2216K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2216. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 80 mm bore?",
        "a": "The 22xx is the wide light section: 140×33 mm with a 30.0 mm radial section at 80 mm bore, wider than a 1216 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2216K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1316",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "seal_type": "open",
    "dynamic_load_kN": 89,
    "static_load_kN": 33,
    "fatigue_load_limit_kN": 0.8,
    "limiting_speed_rpm": 3600,
    "speed_oil_rpm": 4300,
    "weight_g": 4240,
    "manufacturer_designation": "1316S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1316S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1316 carries bore code 16 = 80 mm. Outside diameter 170 mm and width 39 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Mount this 80 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 80 mm bore gains rating through a larger 170 mm OD and 39 mm width; verify the housing accepts the larger envelope before substituting for a 1216.",
      "The open 1316 has no lubricant retention: grease escapes and contaminants migrate straight into the 80×170×39 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1316 units.",
      "A 80 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1316 self-aligning ball bearing?",
        "a": "A 1316 self-aligning ball bearing has a 80 mm bore, 170 mm outer diameter and 39 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1316 bore code work?",
        "a": "The last two digits of 1316 are bore code 16, giving 16 × 5 = 80 mm bore. The 170 mm outside diameter and 39 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1316?",
        "a": "A bare 1316 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 80 mm bore?",
        "a": "The 13xx is the medium section: 170×39 mm, 45.0 mm radial section at 80 mm bore, carrying more load than a 1216 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1316-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1316K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "seal_type": "open",
    "dynamic_load_kN": 89,
    "static_load_kN": 33,
    "fatigue_load_limit_kN": 0.8,
    "limiting_speed_rpm": 3600,
    "speed_oil_rpm": 4300,
    "weight_g": 4240,
    "manufacturer_designation": "1316SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1316SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1316 carries bore code 16 = 80 mm. Outside diameter 170 mm and width 39 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1316. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Mount this 80 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 80 mm bore gains rating through a larger 170 mm OD and 39 mm width; verify the housing accepts the larger envelope before substituting for a 1216.",
      "Tapered-bore 1316K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 80 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1316K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1316K self-aligning ball bearing?",
        "a": "A 1316K self-aligning ball bearing has a 80 mm bore, 170 mm outer diameter and 39 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1316."
      },
      {
        "q": "How does the 1316 bore code work?",
        "a": "The last two digits of 1316 are bore code 16, giving 16 × 5 = 80 mm bore. The 170 mm outside diameter and 39 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1316K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1316. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 80 mm bore?",
        "a": "The 13xx is the medium section: 170×39 mm, 45.0 mm radial section at 80 mm bore, carrying more load than a 1216 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1316K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2316",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 58,
    "seal_type": "open",
    "dynamic_load_kN": 130,
    "static_load_kN": 45,
    "fatigue_load_limit_kN": 1.9,
    "limiting_speed_rpm": 3200,
    "speed_oil_rpm": 4000,
    "weight_g": 5630,
    "manufacturer_designation": "2316S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2316S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2316 carries bore code 16 = 80 mm. Outside diameter 170 mm and width 58 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Mount this 80 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 23xx heavy wide-section at 80 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2316 has no lubricant retention: grease escapes and contaminants migrate straight into the 80×170×58 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2316 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 2316."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2316 self-aligning ball bearing?",
        "a": "A 2316 self-aligning ball bearing has a 80 mm bore, 170 mm outer diameter and 58 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2316 bore code work?",
        "a": "The last two digits of 2316 are bore code 16, giving 16 × 5 = 80 mm bore. The 170 mm outside diameter and 58 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2316?",
        "a": "A bare 2316 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 80 mm bore?",
        "a": "The 23xx is the wide heavy section: 170×58 mm, 45.0 mm radial section at 80 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2316-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2316K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 58,
    "seal_type": "open",
    "dynamic_load_kN": 130,
    "static_load_kN": 45,
    "fatigue_load_limit_kN": 1.9,
    "limiting_speed_rpm": 3200,
    "speed_oil_rpm": 4000,
    "weight_g": 5630,
    "manufacturer_designation": "2316SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2316SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2316 carries bore code 16 = 80 mm. Outside diameter 170 mm and width 58 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2316. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Mount this 80 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 23xx heavy wide-section at 80 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2316K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 80 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2316K self-aligning ball bearing?",
        "a": "A 2316K self-aligning ball bearing has a 80 mm bore, 170 mm outer diameter and 58 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2316."
      },
      {
        "q": "How does the 2316 bore code work?",
        "a": "The last two digits of 2316 are bore code 16, giving 16 × 5 = 80 mm bore. The 170 mm outside diameter and 58 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2316K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2316. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 80 mm bore?",
        "a": "The 23xx is the wide heavy section: 170×58 mm, 45.0 mm radial section at 80 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2316K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1217",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "seal_type": "open",
    "dynamic_load_kN": 49.5,
    "static_load_kN": 20.8,
    "fatigue_load_limit_kN": 0.83,
    "limiting_speed_rpm": 3800,
    "speed_oil_rpm": 4500,
    "weight_g": 2100,
    "manufacturer_designation": "1217S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1217S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1217 carries bore code 17 = 85 mm. Outside diameter 150 mm and width 28 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 85 mm bore uses a smaller 150 mm OD than a 1317; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1217 has no lubricant retention: grease escapes and contaminants migrate straight into the 85×150×28 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1217 units.",
      "A 85 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1217 self-aligning ball bearing?",
        "a": "A 1217 self-aligning ball bearing has a 85 mm bore, 150 mm outer diameter and 28 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1217 bore code work?",
        "a": "The last two digits of 1217 are bore code 17, giving 17 × 5 = 85 mm bore. The 150 mm outside diameter and 28 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1217?",
        "a": "A bare 1217 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 85 mm bore?",
        "a": "The 12xx is the light section: 150×28 mm with a 32.5 mm radial section at 85 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1217-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1217K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "seal_type": "open",
    "dynamic_load_kN": 49.5,
    "static_load_kN": 20.8,
    "fatigue_load_limit_kN": 0.83,
    "limiting_speed_rpm": 3800,
    "speed_oil_rpm": 4500,
    "weight_g": 2100,
    "manufacturer_designation": "1217SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1217SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1217 carries bore code 17 = 85 mm. Outside diameter 150 mm and width 28 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1217. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 85 mm bore uses a smaller 150 mm OD than a 1317; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1217K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 85 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1217K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1217K self-aligning ball bearing?",
        "a": "A 1217K self-aligning ball bearing has a 85 mm bore, 150 mm outer diameter and 28 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1217."
      },
      {
        "q": "How does the 1217 bore code work?",
        "a": "The last two digits of 1217 are bore code 17, giving 17 × 5 = 85 mm bore. The 150 mm outside diameter and 28 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1217K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1217. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 85 mm bore?",
        "a": "The 12xx is the light section: 150×28 mm with a 32.5 mm radial section at 85 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1217K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2217",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 36,
    "seal_type": "open",
    "dynamic_load_kN": 58.5,
    "static_load_kN": 23.6,
    "fatigue_load_limit_kN": 1.5,
    "limiting_speed_rpm": 3800,
    "speed_oil_rpm": 4800,
    "weight_g": 2560,
    "manufacturer_designation": "2217S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2217S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2217 carries bore code 17 = 85 mm. Outside diameter 150 mm and width 36 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 85 mm bore adds load capacity through increased 36 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1217.",
      "The open 2217 has no lubricant retention: grease escapes and contaminants migrate straight into the 85×150×36 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2217 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 2217."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2217 self-aligning ball bearing?",
        "a": "A 2217 self-aligning ball bearing has a 85 mm bore, 150 mm outer diameter and 36 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2217 bore code work?",
        "a": "The last two digits of 2217 are bore code 17, giving 17 × 5 = 85 mm bore. The 150 mm outside diameter and 36 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2217?",
        "a": "A bare 2217 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 85 mm bore?",
        "a": "The 22xx is the wide light section: 150×36 mm with a 32.5 mm radial section at 85 mm bore, wider than a 1217 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2217-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2217K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 36,
    "seal_type": "open",
    "dynamic_load_kN": 58.5,
    "static_load_kN": 23.6,
    "fatigue_load_limit_kN": 1.5,
    "limiting_speed_rpm": 3800,
    "speed_oil_rpm": 4800,
    "weight_g": 2560,
    "manufacturer_designation": "2217SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2217SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2217 carries bore code 17 = 85 mm. Outside diameter 150 mm and width 36 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2217. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 85 mm bore adds load capacity through increased 36 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1217.",
      "Tapered-bore 2217K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 85 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2217K self-aligning ball bearing?",
        "a": "A 2217K self-aligning ball bearing has a 85 mm bore, 150 mm outer diameter and 36 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2217."
      },
      {
        "q": "How does the 2217 bore code work?",
        "a": "The last two digits of 2217 are bore code 17, giving 17 × 5 = 85 mm bore. The 150 mm outside diameter and 36 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2217K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2217. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 85 mm bore?",
        "a": "The 22xx is the wide light section: 150×36 mm with a 32.5 mm radial section at 85 mm bore, wider than a 1217 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2217K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1317",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "seal_type": "open",
    "dynamic_load_kN": 98.5,
    "static_load_kN": 38,
    "fatigue_load_limit_kN": 0.95,
    "limiting_speed_rpm": 3400,
    "speed_oil_rpm": 4000,
    "weight_g": 5030,
    "manufacturer_designation": "1317S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1317S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1317 carries bore code 17 = 85 mm. Outside diameter 180 mm and width 41 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 85 mm bore gains rating through a larger 180 mm OD and 41 mm width; verify the housing accepts the larger envelope before substituting for a 1217.",
      "The open 1317 has no lubricant retention: grease escapes and contaminants migrate straight into the 85×180×41 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1317 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 41 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1317 self-aligning ball bearing?",
        "a": "A 1317 self-aligning ball bearing has a 85 mm bore, 180 mm outer diameter and 41 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1317 bore code work?",
        "a": "The last two digits of 1317 are bore code 17, giving 17 × 5 = 85 mm bore. The 180 mm outside diameter and 41 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1317?",
        "a": "A bare 1317 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 85 mm bore?",
        "a": "The 13xx is the medium section: 180×41 mm, 47.5 mm radial section at 85 mm bore, carrying more load than a 1217 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1317-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1317K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "seal_type": "open",
    "dynamic_load_kN": 98.5,
    "static_load_kN": 38,
    "fatigue_load_limit_kN": 0.95,
    "limiting_speed_rpm": 3400,
    "speed_oil_rpm": 4000,
    "weight_g": 5030,
    "manufacturer_designation": "1317SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1317SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1317 carries bore code 17 = 85 mm. Outside diameter 180 mm and width 41 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1317. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 85 mm bore gains rating through a larger 180 mm OD and 41 mm width; verify the housing accepts the larger envelope before substituting for a 1217.",
      "Tapered-bore 1317K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 85 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1317K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1317K self-aligning ball bearing?",
        "a": "A 1317K self-aligning ball bearing has a 85 mm bore, 180 mm outer diameter and 41 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1317."
      },
      {
        "q": "How does the 1317 bore code work?",
        "a": "The last two digits of 1317 are bore code 17, giving 17 × 5 = 85 mm bore. The 180 mm outside diameter and 41 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1317K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1317. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 85 mm bore?",
        "a": "The 13xx is the medium section: 180×41 mm, 47.5 mm radial section at 85 mm bore, carrying more load than a 1217 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1317K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2317",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 60,
    "seal_type": "open",
    "dynamic_load_kN": 142,
    "static_load_kN": 51.5,
    "fatigue_load_limit_kN": 2.1,
    "limiting_speed_rpm": 3000,
    "speed_oil_rpm": 3800,
    "weight_g": 6560,
    "manufacturer_designation": "2317S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2317S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2317 carries bore code 17 = 85 mm. Outside diameter 180 mm and width 60 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 23xx heavy wide-section at 85 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2317 has no lubricant retention: grease escapes and contaminants migrate straight into the 85×180×60 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2317 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2317."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2317 self-aligning ball bearing?",
        "a": "A 2317 self-aligning ball bearing has a 85 mm bore, 180 mm outer diameter and 60 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2317 bore code work?",
        "a": "The last two digits of 2317 are bore code 17, giving 17 × 5 = 85 mm bore. The 180 mm outside diameter and 60 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2317?",
        "a": "A bare 2317 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 85 mm bore?",
        "a": "The 23xx is the wide heavy section: 180×60 mm, 47.5 mm radial section at 85 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2317-KM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2317-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2317K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 60,
    "seal_type": "open",
    "dynamic_load_kN": 142,
    "static_load_kN": 51.5,
    "fatigue_load_limit_kN": 2.1,
    "limiting_speed_rpm": 3000,
    "speed_oil_rpm": 3800,
    "weight_g": 6560,
    "manufacturer_designation": "2317SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2317SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2317 carries bore code 17 = 85 mm. Outside diameter 180 mm and width 60 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2317. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 23xx heavy wide-section at 85 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2317K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 85 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2317-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2317K self-aligning ball bearing?",
        "a": "A 2317K self-aligning ball bearing has a 85 mm bore, 180 mm outer diameter and 60 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2317."
      },
      {
        "q": "How does the 2317 bore code work?",
        "a": "The last two digits of 2317 are bore code 17, giving 17 × 5 = 85 mm bore. The 180 mm outside diameter and 60 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2317K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2317. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 85 mm bore?",
        "a": "The 23xx is the wide heavy section: 180×60 mm, 47.5 mm radial section at 85 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2317K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1218",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 30,
    "seal_type": "open",
    "dynamic_load_kN": 57.5,
    "static_load_kN": 23.5,
    "fatigue_load_limit_kN": 0.94,
    "limiting_speed_rpm": 3600,
    "speed_oil_rpm": 4300,
    "weight_g": 2560,
    "manufacturer_designation": "1218S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1218S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1218 carries bore code 18 = 90 mm. Outside diameter 160 mm and width 30 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Mount this 90 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 90 mm bore uses a smaller 160 mm OD than a 1318; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1218 has no lubricant retention: grease escapes and contaminants migrate straight into the 90×160×30 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1218 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 30 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1218 self-aligning ball bearing?",
        "a": "A 1218 self-aligning ball bearing has a 90 mm bore, 160 mm outer diameter and 30 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1218 bore code work?",
        "a": "The last two digits of 1218 are bore code 18, giving 18 × 5 = 90 mm bore. The 160 mm outside diameter and 30 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1218?",
        "a": "A bare 1218 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 90 mm bore?",
        "a": "The 12xx is the light section: 160×30 mm with a 35.0 mm radial section at 90 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1218-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1218K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 30,
    "seal_type": "open",
    "dynamic_load_kN": 57.5,
    "static_load_kN": 23.5,
    "fatigue_load_limit_kN": 0.94,
    "limiting_speed_rpm": 3600,
    "speed_oil_rpm": 4300,
    "weight_g": 2560,
    "manufacturer_designation": "1218SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1218SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1218 carries bore code 18 = 90 mm. Outside diameter 160 mm and width 30 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1218. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Mount this 90 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 90 mm bore uses a smaller 160 mm OD than a 1318; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1218K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 90 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1218K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1218K self-aligning ball bearing?",
        "a": "A 1218K self-aligning ball bearing has a 90 mm bore, 160 mm outer diameter and 30 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1218."
      },
      {
        "q": "How does the 1218 bore code work?",
        "a": "The last two digits of 1218 are bore code 18, giving 18 × 5 = 90 mm bore. The 160 mm outside diameter and 30 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1218K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1218. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 90 mm bore?",
        "a": "The 12xx is the light section: 160×30 mm with a 35.0 mm radial section at 90 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1218K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2218",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 40,
    "seal_type": "open",
    "dynamic_load_kN": 70.5,
    "static_load_kN": 28.7,
    "fatigue_load_limit_kN": 1.8,
    "limiting_speed_rpm": 3600,
    "speed_oil_rpm": 4300,
    "weight_g": 3220,
    "manufacturer_designation": "2218S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2218S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2218 carries bore code 18 = 90 mm. Outside diameter 160 mm and width 40 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Mount this 90 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 90 mm bore adds load capacity through increased 40 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1218.",
      "The open 2218 has no lubricant retention: grease escapes and contaminants migrate straight into the 90×160×40 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2218 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2218."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2218 self-aligning ball bearing?",
        "a": "A 2218 self-aligning ball bearing has a 90 mm bore, 160 mm outer diameter and 40 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2218 bore code work?",
        "a": "The last two digits of 2218 are bore code 18, giving 18 × 5 = 90 mm bore. The 160 mm outside diameter and 40 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2218?",
        "a": "A bare 2218 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 90 mm bore?",
        "a": "The 22xx is the wide light section: 160×40 mm with a 35.0 mm radial section at 90 mm bore, wider than a 1218 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2218-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2218K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 40,
    "seal_type": "open",
    "dynamic_load_kN": 70.5,
    "static_load_kN": 28.7,
    "fatigue_load_limit_kN": 1.8,
    "limiting_speed_rpm": 3600,
    "speed_oil_rpm": 4300,
    "weight_g": 3220,
    "manufacturer_designation": "2218SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2218SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2218 carries bore code 18 = 90 mm. Outside diameter 160 mm and width 40 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2218. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Mount this 90 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 90 mm bore adds load capacity through increased 40 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1218.",
      "Tapered-bore 2218K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 90 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2218-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2218K self-aligning ball bearing?",
        "a": "A 2218K self-aligning ball bearing has a 90 mm bore, 160 mm outer diameter and 40 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2218."
      },
      {
        "q": "How does the 2218 bore code work?",
        "a": "The last two digits of 2218 are bore code 18, giving 18 × 5 = 90 mm bore. The 160 mm outside diameter and 40 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2218K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2218. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 90 mm bore?",
        "a": "The 22xx is the wide light section: 160×40 mm with a 35.0 mm radial section at 90 mm bore, wider than a 1218 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2218K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1318",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "seal_type": "open",
    "dynamic_load_kN": 117,
    "static_load_kN": 44.5,
    "fatigue_load_limit_kN": 1.2,
    "limiting_speed_rpm": 3200,
    "speed_oil_rpm": 3800,
    "weight_g": 5830,
    "manufacturer_designation": "1318S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1318S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1318 carries bore code 18 = 90 mm. Outside diameter 190 mm and width 43 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Mount this 90 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 90 mm bore gains rating through a larger 190 mm OD and 43 mm width; verify the housing accepts the larger envelope before substituting for a 1218.",
      "The open 1318 has no lubricant retention: grease escapes and contaminants migrate straight into the 90×190×43 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1318 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1318."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1318 self-aligning ball bearing?",
        "a": "A 1318 self-aligning ball bearing has a 90 mm bore, 190 mm outer diameter and 43 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1318 bore code work?",
        "a": "The last two digits of 1318 are bore code 18, giving 18 × 5 = 90 mm bore. The 190 mm outside diameter and 43 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1318?",
        "a": "A bare 1318 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 90 mm bore?",
        "a": "The 13xx is the medium section: 190×43 mm, 50.0 mm radial section at 90 mm bore, carrying more load than a 1218 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1318-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1318K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "seal_type": "open",
    "dynamic_load_kN": 117,
    "static_load_kN": 44.5,
    "fatigue_load_limit_kN": 1.2,
    "limiting_speed_rpm": 3200,
    "speed_oil_rpm": 3800,
    "weight_g": 5830,
    "manufacturer_designation": "1318SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1318SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1318 carries bore code 18 = 90 mm. Outside diameter 190 mm and width 43 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1318. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Mount this 90 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 90 mm bore gains rating through a larger 190 mm OD and 43 mm width; verify the housing accepts the larger envelope before substituting for a 1218.",
      "Tapered-bore 1318K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 90 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1318K self-aligning ball bearing?",
        "a": "A 1318K self-aligning ball bearing has a 90 mm bore, 190 mm outer diameter and 43 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1318."
      },
      {
        "q": "How does the 1318 bore code work?",
        "a": "The last two digits of 1318 are bore code 18, giving 18 × 5 = 90 mm bore. The 190 mm outside diameter and 43 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1318K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1318. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 90 mm bore?",
        "a": "The 13xx is the medium section: 190×43 mm, 50.0 mm radial section at 90 mm bore, carrying more load than a 1218 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1318K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2318",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 64,
    "seal_type": "open",
    "dynamic_load_kN": 154,
    "static_load_kN": 57.5,
    "fatigue_load_limit_kN": 2.4,
    "limiting_speed_rpm": 2800,
    "speed_oil_rpm": 3600,
    "weight_g": 7750,
    "manufacturer_designation": "2318S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2318S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2318 carries bore code 18 = 90 mm. Outside diameter 190 mm and width 64 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Mount this 90 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 23xx heavy wide-section at 90 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2318 has no lubricant retention: grease escapes and contaminants migrate straight into the 90×190×64 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2318 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2318 self-aligning ball bearing?",
        "a": "A 2318 self-aligning ball bearing has a 90 mm bore, 190 mm outer diameter and 64 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2318 bore code work?",
        "a": "The last two digits of 2318 are bore code 18, giving 18 × 5 = 90 mm bore. The 190 mm outside diameter and 64 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2318?",
        "a": "A bare 2318 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 90 mm bore?",
        "a": "The 23xx is the wide heavy section: 190×64 mm, 50.0 mm radial section at 90 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2318-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2318K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 64,
    "seal_type": "open",
    "dynamic_load_kN": 154,
    "static_load_kN": 57.5,
    "fatigue_load_limit_kN": 2.4,
    "limiting_speed_rpm": 2800,
    "speed_oil_rpm": 3600,
    "weight_g": 7750,
    "manufacturer_designation": "2318SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2318SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2318 carries bore code 18 = 90 mm. Outside diameter 190 mm and width 64 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2318. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Mount this 90 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 23xx heavy wide-section at 90 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2318K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 90 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "A 90 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2318K self-aligning ball bearing?",
        "a": "A 2318K self-aligning ball bearing has a 90 mm bore, 190 mm outer diameter and 64 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2318."
      },
      {
        "q": "How does the 2318 bore code work?",
        "a": "The last two digits of 2318 are bore code 18, giving 18 × 5 = 90 mm bore. The 190 mm outside diameter and 64 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2318K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2318. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 90 mm bore?",
        "a": "The 23xx is the wide heavy section: 190×64 mm, 50.0 mm radial section at 90 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2318K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1219",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "seal_type": "open",
    "dynamic_load_kN": 64,
    "static_load_kN": 27.1,
    "fatigue_load_limit_kN": 1.1,
    "limiting_speed_rpm": 3400,
    "speed_oil_rpm": 4000,
    "weight_g": 3120,
    "manufacturer_designation": "1219S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1219S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1219 carries bore code 19 = 95 mm. Outside diameter 170 mm and width 32 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Mount this 95 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 95 mm bore uses a smaller 170 mm OD than a 1319; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1219 has no lubricant retention: grease escapes and contaminants migrate straight into the 95×170×32 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1219 units.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1219."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1219 self-aligning ball bearing?",
        "a": "A 1219 self-aligning ball bearing has a 95 mm bore, 170 mm outer diameter and 32 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1219 bore code work?",
        "a": "The last two digits of 1219 are bore code 19, giving 19 × 5 = 95 mm bore. The 170 mm outside diameter and 32 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1219?",
        "a": "A bare 1219 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 95 mm bore?",
        "a": "The 12xx is the light section: 170×32 mm with a 37.5 mm radial section at 95 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1219-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1219K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "seal_type": "open",
    "dynamic_load_kN": 64,
    "static_load_kN": 27.1,
    "fatigue_load_limit_kN": 1.1,
    "limiting_speed_rpm": 3400,
    "speed_oil_rpm": 4000,
    "weight_g": 3120,
    "manufacturer_designation": "1219SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1219SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1219 carries bore code 19 = 95 mm. Outside diameter 170 mm and width 32 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1219. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Mount this 95 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 95 mm bore uses a smaller 170 mm OD than a 1319; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1219K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 95 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1219K self-aligning ball bearing?",
        "a": "A 1219K self-aligning ball bearing has a 95 mm bore, 170 mm outer diameter and 32 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1219."
      },
      {
        "q": "How does the 1219 bore code work?",
        "a": "The last two digits of 1219 are bore code 19, giving 19 × 5 = 95 mm bore. The 170 mm outside diameter and 32 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1219K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1219. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 95 mm bore?",
        "a": "The 12xx is the light section: 170×32 mm with a 37.5 mm radial section at 95 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1219K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2219",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 43,
    "seal_type": "open",
    "dynamic_load_kN": 84,
    "static_load_kN": 34.5,
    "fatigue_load_limit_kN": 2,
    "limiting_speed_rpm": 3400,
    "speed_oil_rpm": 4000,
    "weight_g": 3960,
    "manufacturer_designation": "2219S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2219S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2219 carries bore code 19 = 95 mm. Outside diameter 170 mm and width 43 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Mount this 95 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 95 mm bore adds load capacity through increased 43 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1219.",
      "The open 2219 has no lubricant retention: grease escapes and contaminants migrate straight into the 95×170×43 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2219 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2219 self-aligning ball bearing?",
        "a": "A 2219 self-aligning ball bearing has a 95 mm bore, 170 mm outer diameter and 43 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2219 bore code work?",
        "a": "The last two digits of 2219 are bore code 19, giving 19 × 5 = 95 mm bore. The 170 mm outside diameter and 43 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2219?",
        "a": "A bare 2219 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 95 mm bore?",
        "a": "The 22xx is the wide light section: 170×43 mm with a 37.5 mm radial section at 95 mm bore, wider than a 1219 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2219-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2219K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 43,
    "seal_type": "open",
    "dynamic_load_kN": 84,
    "static_load_kN": 34.5,
    "fatigue_load_limit_kN": 2,
    "limiting_speed_rpm": 3400,
    "speed_oil_rpm": 4000,
    "weight_g": 3960,
    "manufacturer_designation": "2219SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2219SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2219 carries bore code 19 = 95 mm. Outside diameter 170 mm and width 43 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2219. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Mount this 95 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 95 mm bore adds load capacity through increased 43 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1219.",
      "Tapered-bore 2219K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 95 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "A 95 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2219K self-aligning ball bearing?",
        "a": "A 2219K self-aligning ball bearing has a 95 mm bore, 170 mm outer diameter and 43 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2219."
      },
      {
        "q": "How does the 2219 bore code work?",
        "a": "The last two digits of 2219 are bore code 19, giving 19 × 5 = 95 mm bore. The 170 mm outside diameter and 43 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2219K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2219. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 95 mm bore?",
        "a": "The 22xx is the wide light section: 170×43 mm with a 37.5 mm radial section at 95 mm bore, wider than a 1219 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2219K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1319",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "seal_type": "open",
    "dynamic_load_kN": 129,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 1.4,
    "limiting_speed_rpm": 3000,
    "speed_oil_rpm": 3600,
    "weight_g": 6790,
    "manufacturer_designation": "1319S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1319S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1319 carries bore code 19 = 95 mm. Outside diameter 200 mm and width 45 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Mount this 95 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 95 mm bore gains rating through a larger 200 mm OD and 45 mm width; verify the housing accepts the larger envelope before substituting for a 1219.",
      "The open 1319 has no lubricant retention: grease escapes and contaminants migrate straight into the 95×200×45 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1319 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1319."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1319 self-aligning ball bearing?",
        "a": "A 1319 self-aligning ball bearing has a 95 mm bore, 200 mm outer diameter and 45 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1319 bore code work?",
        "a": "The last two digits of 1319 are bore code 19, giving 19 × 5 = 95 mm bore. The 200 mm outside diameter and 45 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1319?",
        "a": "A bare 1319 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 95 mm bore?",
        "a": "The 13xx is the medium section: 200×45 mm, 52.5 mm radial section at 95 mm bore, carrying more load than a 1219 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1319-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1319K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "seal_type": "open",
    "dynamic_load_kN": 129,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 1.4,
    "limiting_speed_rpm": 3000,
    "speed_oil_rpm": 3600,
    "weight_g": 6790,
    "manufacturer_designation": "1319SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1319SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1319 carries bore code 19 = 95 mm. Outside diameter 200 mm and width 45 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1319. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Mount this 95 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 95 mm bore gains rating through a larger 200 mm OD and 45 mm width; verify the housing accepts the larger envelope before substituting for a 1219.",
      "Tapered-bore 1319K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 95 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1319-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1319K self-aligning ball bearing?",
        "a": "A 1319K self-aligning ball bearing has a 95 mm bore, 200 mm outer diameter and 45 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1319."
      },
      {
        "q": "How does the 1319 bore code work?",
        "a": "The last two digits of 1319 are bore code 19, giving 19 × 5 = 95 mm bore. The 200 mm outside diameter and 45 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1319K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1319. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 95 mm bore?",
        "a": "The 13xx is the medium section: 200×45 mm, 52.5 mm radial section at 95 mm bore, carrying more load than a 1219 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1319K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2319",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 67,
    "seal_type": "open",
    "dynamic_load_kN": 161,
    "static_load_kN": 64.5,
    "fatigue_load_limit_kN": 2.7,
    "limiting_speed_rpm": 2800,
    "speed_oil_rpm": 3400,
    "weight_g": 8970,
    "manufacturer_designation": "2319S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2319S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2319 carries bore code 19 = 95 mm. Outside diameter 200 mm and width 67 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Mount this 95 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 23xx heavy wide-section at 95 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2319 has no lubricant retention: grease escapes and contaminants migrate straight into the 95×200×67 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2319 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2319-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2319 self-aligning ball bearing?",
        "a": "A 2319 self-aligning ball bearing has a 95 mm bore, 200 mm outer diameter and 67 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2319 bore code work?",
        "a": "The last two digits of 2319 are bore code 19, giving 19 × 5 = 95 mm bore. The 200 mm outside diameter and 67 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2319?",
        "a": "A bare 2319 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 95 mm bore?",
        "a": "The 23xx is the wide heavy section: 200×67 mm, 52.5 mm radial section at 95 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2319-KM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2319-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2319K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 67,
    "seal_type": "open",
    "dynamic_load_kN": 161,
    "static_load_kN": 64.5,
    "fatigue_load_limit_kN": 2.7,
    "limiting_speed_rpm": 2800,
    "speed_oil_rpm": 3400,
    "weight_g": 8970,
    "manufacturer_designation": "2319SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2319SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2319 carries bore code 19 = 95 mm. Outside diameter 200 mm and width 67 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2319. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Mount this 95 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 23xx heavy wide-section at 95 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2319K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 95 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Shaft and housing fillets must clear the bearing chamfer so the 67 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2319K self-aligning ball bearing?",
        "a": "A 2319K self-aligning ball bearing has a 95 mm bore, 200 mm outer diameter and 67 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2319."
      },
      {
        "q": "How does the 2319 bore code work?",
        "a": "The last two digits of 2319 are bore code 19, giving 19 × 5 = 95 mm bore. The 200 mm outside diameter and 67 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2319K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2319. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 95 mm bore?",
        "a": "The 23xx is the wide heavy section: 200×67 mm, 52.5 mm radial section at 95 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2319K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1220",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 34,
    "seal_type": "open",
    "dynamic_load_kN": 69.5,
    "static_load_kN": 29.7,
    "fatigue_load_limit_kN": 1.2,
    "limiting_speed_rpm": 3200,
    "speed_oil_rpm": 3800,
    "weight_g": 3740,
    "manufacturer_designation": "1220S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1220S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1220 carries bore code 20 = 100 mm. Outside diameter 180 mm and width 34 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Mount this 100 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 100 mm bore uses a smaller 180 mm OD than a 1320; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1220 has no lubricant retention: grease escapes and contaminants migrate straight into the 100×180×34 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1220 units.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 1220."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1220 self-aligning ball bearing?",
        "a": "A 1220 self-aligning ball bearing has a 100 mm bore, 180 mm outer diameter and 34 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1220 bore code work?",
        "a": "The last two digits of 1220 are bore code 20, giving 20 × 5 = 100 mm bore. The 180 mm outside diameter and 34 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1220?",
        "a": "A bare 1220 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 100 mm bore?",
        "a": "The 12xx is the light section: 180×34 mm with a 40.0 mm radial section at 100 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1220-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1220K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 34,
    "seal_type": "open",
    "dynamic_load_kN": 69.5,
    "static_load_kN": 29.7,
    "fatigue_load_limit_kN": 1.2,
    "limiting_speed_rpm": 3200,
    "speed_oil_rpm": 3800,
    "weight_g": 3740,
    "manufacturer_designation": "1220SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1220SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1220 carries bore code 20 = 100 mm. Outside diameter 180 mm and width 34 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1220. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Mount this 100 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 100 mm bore uses a smaller 180 mm OD than a 1320; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1220K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 100 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1220-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1220K self-aligning ball bearing?",
        "a": "A 1220K self-aligning ball bearing has a 100 mm bore, 180 mm outer diameter and 34 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1220."
      },
      {
        "q": "How does the 1220 bore code work?",
        "a": "The last two digits of 1220 are bore code 20, giving 20 × 5 = 100 mm bore. The 180 mm outside diameter and 34 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1220K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1220. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 100 mm bore?",
        "a": "The 12xx is the light section: 180×34 mm with a 40.0 mm radial section at 100 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1220K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2220",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 46,
    "seal_type": "open",
    "dynamic_load_kN": 94.5,
    "static_load_kN": 38.5,
    "fatigue_load_limit_kN": 2.3,
    "limiting_speed_rpm": 3200,
    "speed_oil_rpm": 3800,
    "weight_g": 4710,
    "manufacturer_designation": "2220S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2220S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2220 carries bore code 20 = 100 mm. Outside diameter 180 mm and width 46 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Mount this 100 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 100 mm bore adds load capacity through increased 46 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1220.",
      "The open 2220 has no lubricant retention: grease escapes and contaminants migrate straight into the 100×180×46 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2220 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 2220-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2220 self-aligning ball bearing?",
        "a": "A 2220 self-aligning ball bearing has a 100 mm bore, 180 mm outer diameter and 46 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2220 bore code work?",
        "a": "The last two digits of 2220 are bore code 20, giving 20 × 5 = 100 mm bore. The 180 mm outside diameter and 46 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2220?",
        "a": "A bare 2220 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 100 mm bore?",
        "a": "The 22xx is the wide light section: 180×46 mm with a 40.0 mm radial section at 100 mm bore, wider than a 1220 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2220-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2220K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 46,
    "seal_type": "open",
    "dynamic_load_kN": 94.5,
    "static_load_kN": 38.5,
    "fatigue_load_limit_kN": 2.3,
    "limiting_speed_rpm": 3200,
    "speed_oil_rpm": 3800,
    "weight_g": 4710,
    "manufacturer_designation": "2220SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2220SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2220 carries bore code 20 = 100 mm. Outside diameter 180 mm and width 46 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2220. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Mount this 100 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 100 mm bore adds load capacity through increased 46 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1220.",
      "Tapered-bore 2220K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 100 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Shaft and housing fillets must clear the bearing chamfer so the 46 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2220K self-aligning ball bearing?",
        "a": "A 2220K self-aligning ball bearing has a 100 mm bore, 180 mm outer diameter and 46 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2220."
      },
      {
        "q": "How does the 2220 bore code work?",
        "a": "The last two digits of 2220 are bore code 20, giving 20 × 5 = 100 mm bore. The 180 mm outside diameter and 46 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2220K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2220. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 100 mm bore?",
        "a": "The 22xx is the wide light section: 180×46 mm with a 40.0 mm radial section at 100 mm bore, wider than a 1220 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2220K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1320",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "seal_type": "open",
    "dynamic_load_kN": 140,
    "static_load_kN": 57.5,
    "fatigue_load_limit_kN": 1.6,
    "limiting_speed_rpm": 2800,
    "speed_oil_rpm": 3400,
    "weight_g": 8400,
    "manufacturer_designation": "1320S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1320S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1320 carries bore code 20 = 100 mm. Outside diameter 215 mm and width 47 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Mount this 100 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 100 mm bore gains rating through a larger 215 mm OD and 47 mm width; verify the housing accepts the larger envelope before substituting for a 1220.",
      "The open 1320 has no lubricant retention: grease escapes and contaminants migrate straight into the 100×215×47 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1320 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1320 self-aligning ball bearing?",
        "a": "A 1320 self-aligning ball bearing has a 100 mm bore, 215 mm outer diameter and 47 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1320 bore code work?",
        "a": "The last two digits of 1320 are bore code 20, giving 20 × 5 = 100 mm bore. The 215 mm outside diameter and 47 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1320?",
        "a": "A bare 1320 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 100 mm bore?",
        "a": "The 13xx is the medium section: 215×47 mm, 57.5 mm radial section at 100 mm bore, carrying more load than a 1220 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1320-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1320K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "seal_type": "open",
    "dynamic_load_kN": 140,
    "static_load_kN": 57.5,
    "fatigue_load_limit_kN": 1.6,
    "limiting_speed_rpm": 2800,
    "speed_oil_rpm": 3400,
    "weight_g": 8400,
    "manufacturer_designation": "1320SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1320SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1320 carries bore code 20 = 100 mm. Outside diameter 215 mm and width 47 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1320. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Mount this 100 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 100 mm bore gains rating through a larger 215 mm OD and 47 mm width; verify the housing accepts the larger envelope before substituting for a 1220.",
      "Tapered-bore 1320K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 100 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "A 100 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1320K self-aligning ball bearing?",
        "a": "A 1320K self-aligning ball bearing has a 100 mm bore, 215 mm outer diameter and 47 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1320."
      },
      {
        "q": "How does the 1320 bore code work?",
        "a": "The last two digits of 1320 are bore code 20, giving 20 × 5 = 100 mm bore. The 215 mm outside diameter and 47 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1320K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1320. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 100 mm bore?",
        "a": "The 13xx is the medium section: 215×47 mm, 57.5 mm radial section at 100 mm bore, carrying more load than a 1220 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1320K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2320",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 73,
    "seal_type": "open",
    "dynamic_load_kN": 187,
    "static_load_kN": 79,
    "fatigue_load_limit_kN": 3.3,
    "limiting_speed_rpm": 2400,
    "speed_oil_rpm": 3200,
    "weight_g": 11500,
    "manufacturer_designation": "2320S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2320S"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2320 carries bore code 20 = 100 mm. Outside diameter 215 mm and width 73 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Mount this 100 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 23xx heavy wide-section at 100 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "The open 2320 has no lubricant retention: grease escapes and contaminants migrate straight into the 100×215×73 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2320 units.",
      "A 100 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2320 self-aligning ball bearing?",
        "a": "A 2320 self-aligning ball bearing has a 100 mm bore, 215 mm outer diameter and 73 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2320 bore code work?",
        "a": "The last two digits of 2320 are bore code 20, giving 20 × 5 = 100 mm bore. The 215 mm outside diameter and 73 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2320?",
        "a": "A bare 2320 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 100 mm bore?",
        "a": "The 23xx is the wide heavy section: 215×73 mm, 57.5 mm radial section at 100 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2320-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2320K",
    "brand": "NTN",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 73,
    "seal_type": "open",
    "dynamic_load_kN": 187,
    "static_load_kN": 79,
    "fatigue_load_limit_kN": 3.3,
    "limiting_speed_rpm": 2400,
    "speed_oil_rpm": 3200,
    "weight_g": 11500,
    "manufacturer_designation": "2320SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2320SK"
    ],
    "naming_rule_text": "In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2320 carries bore code 20 = 100 mm. Outside diameter 215 mm and width 73 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2320. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Mount this 100 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 23xx heavy wide-section at 100 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.",
      "Tapered-bore 2320K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 100 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 2320K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2320K self-aligning ball bearing?",
        "a": "A 2320K self-aligning ball bearing has a 100 mm bore, 215 mm outer diameter and 73 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2320."
      },
      {
        "q": "How does the 2320 bore code work?",
        "a": "The last two digits of 2320 are bore code 20, giving 20 × 5 = 100 mm bore. The 215 mm outside diameter and 73 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2320K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2320. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2300 compare with other self-aligning series at the same 100 mm bore?",
        "a": "The 23xx is the wide heavy section: 215×73 mm, 57.5 mm radial section at 100 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2320K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1221",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 105,
    "D_mm": 190,
    "B_mm": 36,
    "seal_type": "open",
    "dynamic_load_kN": 75,
    "static_load_kN": 32.5,
    "fatigue_load_limit_kN": 1.3,
    "limiting_speed_rpm": 3000,
    "speed_oil_rpm": 3600,
    "weight_g": 4430,
    "manufacturer_designation": "1221S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1221S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1221 carries bore code 21 = 105 mm. Outside diameter 190 mm and width 36 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Mount this 105 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 105 mm bore uses a smaller 190 mm OD than a 1321; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1221 has no lubricant retention: grease escapes and contaminants migrate straight into the 105×190×36 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1221 units.",
      "Do not use a self-aligning ball bearing where high radial rigidity is required — the sphered outer raceway allows more radial movement than a deep-groove or cylindrical roller bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1221 self-aligning ball bearing?",
        "a": "A 1221 self-aligning ball bearing has a 105 mm bore, 190 mm outer diameter and 36 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1221 bore code work?",
        "a": "The last two digits of 1221 are bore code 21, giving 21 × 5 = 105 mm bore. The 190 mm outside diameter and 36 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1221?",
        "a": "A bare 1221 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 105 mm bore?",
        "a": "The 12xx is the light section: 190×36 mm with a 42.5 mm radial section at 105 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1221",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2221",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 105,
    "D_mm": 190,
    "B_mm": 50,
    "seal_type": "open",
    "dynamic_load_kN": 109,
    "static_load_kN": 45,
    "fatigue_load_limit_kN": 2.6,
    "limiting_speed_rpm": 3000,
    "speed_oil_rpm": 3600,
    "weight_g": 5730,
    "manufacturer_designation": "2221S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2221S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2221 carries bore code 21 = 105 mm. Outside diameter 190 mm and width 50 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Mount this 105 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 105 mm bore adds load capacity through increased 50 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1221.",
      "The open 2221 has no lubricant retention: grease escapes and contaminants migrate straight into the 105×190×50 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2221 units.",
      "A 105 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2221 self-aligning ball bearing?",
        "a": "A 2221 self-aligning ball bearing has a 105 mm bore, 190 mm outer diameter and 50 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2221 bore code work?",
        "a": "The last two digits of 2221 are bore code 21, giving 21 × 5 = 105 mm bore. The 190 mm outside diameter and 50 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2221?",
        "a": "A bare 2221 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 105 mm bore?",
        "a": "The 22xx is the wide light section: 190×50 mm with a 42.5 mm radial section at 105 mm bore, wider than a 1221 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2221",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1321",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 105,
    "D_mm": 225,
    "B_mm": 49,
    "seal_type": "open",
    "dynamic_load_kN": 154,
    "static_load_kN": 64.5,
    "fatigue_load_limit_kN": 1.8,
    "limiting_speed_rpm": 2600,
    "speed_oil_rpm": 3200,
    "weight_g": 9580,
    "manufacturer_designation": "1321S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1321S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1321 carries bore code 21 = 105 mm. Outside diameter 225 mm and width 49 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Mount this 105 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 105 mm bore gains rating through a larger 225 mm OD and 49 mm width; verify the housing accepts the larger envelope before substituting for a 1221.",
      "The open 1321 has no lubricant retention: grease escapes and contaminants migrate straight into the 105×225×49 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1321 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1321-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1321 self-aligning ball bearing?",
        "a": "A 1321 self-aligning ball bearing has a 105 mm bore, 225 mm outer diameter and 49 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1321 bore code work?",
        "a": "The last two digits of 1321 are bore code 21, giving 21 × 5 = 105 mm bore. The 225 mm outside diameter and 49 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1321?",
        "a": "A bare 1321 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 105 mm bore?",
        "a": "The 13xx is the medium section: 225×49 mm, 60.0 mm radial section at 105 mm bore, carrying more load than a 1221 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1321",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1222",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 38,
    "seal_type": "open",
    "dynamic_load_kN": 87,
    "static_load_kN": 38.5,
    "fatigue_load_limit_kN": 1.5,
    "limiting_speed_rpm": 2800,
    "speed_oil_rpm": 3400,
    "weight_g": 5210,
    "manufacturer_designation": "1222S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1222S"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1222 carries bore code 22 = 110 mm. Outside diameter 200 mm and width 38 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "fretting corrosion on a loose shaft seat"
    ],
    "pitfalls": [
      "Mount this 110 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 110 mm bore uses a smaller 200 mm OD than a 1322; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "The open 1222 has no lubricant retention: grease escapes and contaminants migrate straight into the 110×200×38 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1222 units.",
      "Suffixes stack in a defined order — clearance follows the bore code, e.g. 1222-C3. No clearance suffix means normal CN clearance."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1222 self-aligning ball bearing?",
        "a": "A 1222 self-aligning ball bearing has a 110 mm bore, 200 mm outer diameter and 38 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1222 bore code work?",
        "a": "The last two digits of 1222 are bore code 22, giving 22 × 5 = 110 mm bore. The 200 mm outside diameter and 38 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1222?",
        "a": "A bare 1222 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 110 mm bore?",
        "a": "The 12xx is the light section: 200×38 mm with a 45.0 mm radial section at 110 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1222-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1222K",
    "brand": "NTN",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 38,
    "seal_type": "open",
    "dynamic_load_kN": 87,
    "static_load_kN": 38.5,
    "fatigue_load_limit_kN": 1.5,
    "limiting_speed_rpm": 2800,
    "speed_oil_rpm": 3400,
    "weight_g": 5210,
    "manufacturer_designation": "1222SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1222SK"
    ],
    "naming_rule_text": "In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1222 carries bore code 22 = 110 mm. Outside diameter 200 mm and width 38 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1222. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "cage wear or fracture from sustained vibration or shock loading",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Mount this 110 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 12xx light section at 110 mm bore uses a smaller 200 mm OD than a 1322; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.",
      "Tapered-bore 1222K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 110 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Shaft and housing fillets must clear the bearing chamfer so the 38 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1222K self-aligning ball bearing?",
        "a": "A 1222K self-aligning ball bearing has a 110 mm bore, 200 mm outer diameter and 38 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1222."
      },
      {
        "q": "How does the 1222 bore code work?",
        "a": "The last two digits of 1222 are bore code 22, giving 22 × 5 = 110 mm bore. The 200 mm outside diameter and 38 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1222K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1222. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1200 compare with other self-aligning series at the same 110 mm bore?",
        "a": "The 12xx is the light section: 200×38 mm with a 45.0 mm radial section at 110 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1222K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "2222",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 53,
    "seal_type": "open",
    "dynamic_load_kN": 122,
    "static_load_kN": 51.5,
    "fatigue_load_limit_kN": 2.9,
    "limiting_speed_rpm": 2800,
    "speed_oil_rpm": 3400,
    "weight_g": 6750,
    "manufacturer_designation": "2222S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2222S"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2222 carries bore code 22 = 110 mm. Outside diameter 200 mm and width 53 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "cage wear or fracture from sustained vibration or shock loading"
    ],
    "pitfalls": [
      "Mount this 110 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 110 mm bore adds load capacity through increased 53 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1222.",
      "The open 2222 has no lubricant retention: grease escapes and contaminants migrate straight into the 110×200×53 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 2200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2222 units.",
      "Shaft and housing fillets must clear the bearing chamfer so the 53 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2222 self-aligning ball bearing?",
        "a": "A 2222 self-aligning ball bearing has a 110 mm bore, 200 mm outer diameter and 53 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 2222 bore code work?",
        "a": "The last two digits of 2222 are bore code 22, giving 22 × 5 = 110 mm bore. The 200 mm outside diameter and 53 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 2222?",
        "a": "A bare 2222 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 110 mm bore?",
        "a": "The 22xx is the wide light section: 200×53 mm with a 45.0 mm radial section at 110 mm bore, wider than a 1222 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2222-K",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "2222K",
    "brand": "NTN",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 53,
    "seal_type": "open",
    "dynamic_load_kN": 122,
    "static_load_kN": 51.5,
    "fatigue_load_limit_kN": 2.9,
    "limiting_speed_rpm": 2800,
    "speed_oil_rpm": 3400,
    "weight_g": 6750,
    "manufacturer_designation": "2222SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "2222SK"
    ],
    "naming_rule_text": "In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2222 carries bore code 22 = 110 mm. Outside diameter 200 mm and width 53 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2222. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts",
      "pulp, paper and steel mill machinery",
      "heavy industrial drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Mount this 110 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 22xx wide-section at 110 mm bore adds load capacity through increased 53 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1222.",
      "Tapered-bore 2222K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 110 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2222K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 2222K self-aligning ball bearing?",
        "a": "A 2222K self-aligning ball bearing has a 110 mm bore, 200 mm outer diameter and 53 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2222."
      },
      {
        "q": "How does the 2222 bore code work?",
        "a": "The last two digits of 2222 are bore code 22, giving 22 × 5 = 110 mm bore. The 200 mm outside diameter and 53 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 2222K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2222. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 2200 compare with other self-aligning series at the same 110 mm bore?",
        "a": "The 22xx is the wide light section: 200×53 mm with a 45.0 mm radial section at 110 mm bore, wider than a 1222 for higher load capacity at the cost of speed."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "2222K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "1322",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "seal_type": "open",
    "dynamic_load_kN": 161,
    "static_load_kN": 72.5,
    "fatigue_load_limit_kN": 2.1,
    "limiting_speed_rpm": 2400,
    "speed_oil_rpm": 3000,
    "weight_g": 11500,
    "manufacturer_designation": "1322S",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1322S"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1322 carries bore code 22 = 110 mm. Outside diameter 240 mm and width 50 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "heavy industrial drive shafts",
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "fretting corrosion on a loose shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Mount this 110 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 110 mm bore gains rating through a larger 240 mm OD and 50 mm width; verify the housing accepts the larger envelope before substituting for a 1222.",
      "The open 1322 has no lubricant retention: grease escapes and contaminants migrate straight into the 110×240×50 mm raceway, so specify a sealed arrangement for dusty or washdown duty.",
      "Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1322 units.",
      "A 110 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1322 self-aligning ball bearing?",
        "a": "A 1322 self-aligning ball bearing has a 110 mm bore, 240 mm outer diameter and 50 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting."
      },
      {
        "q": "How does the 1322 bore code work?",
        "a": "The last two digits of 1322 are bore code 22, giving 22 × 5 = 110 mm bore. The 240 mm outside diameter and 50 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the open suffix mean on 1322?",
        "a": "A bare 1322 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 110 mm bore?",
        "a": "The 13xx is the medium section: 240×50 mm, 65.0 mm radial section at 110 mm bore, carrying more load than a 1222 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1322-KM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1322-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ]
  },
  {
    "sku": "1322K",
    "brand": "NTN",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "seal_type": "open",
    "dynamic_load_kN": 161,
    "static_load_kN": 72.5,
    "fatigue_load_limit_kN": 2.1,
    "limiting_speed_rpm": 2400,
    "speed_oil_rpm": 3000,
    "weight_g": 11500,
    "manufacturer_designation": "1322SK",
    "standard": "ISO 15",
    "source_ref": "https://www.ntnglobal.com/",
    "catalog_ver": "CAT. No. 2203-3/E 2024",
    "extracted_at": "2026-09-25",
    "aliases": [
      "1322SK"
    ],
    "naming_rule_text": "In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1322 carries bore code 22 = 110 mm. Outside diameter 240 mm and width 50 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1322. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.",
    "applications": [
      "large gearbox and reducer shafts",
      "industrial fan and blower rotors",
      "hoist, winch and crane drums",
      "heavy conveyor drive shafts"
    ],
    "failure_modes": [
      "contamination wear from dust and dirt ingress through the open arrangement",
      "lubricant starvation when no regreasing interval is maintained",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and stress concentration from excessive misalignment beyond the allowable angle"
    ],
    "pitfalls": [
      "Mount this 110 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.",
      "The 13xx medium section at 110 mm bore gains rating through a larger 240 mm OD and 50 mm width; verify the housing accepts the larger envelope before substituting for a 1222.",
      "Tapered-bore 1322K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 110 mm shaft before ordering.",
      "The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.",
      "The self-aligning feature compensates for static misalignment and shaft deflection, not for poor initial alignment — always align shaft and housing as accurately as possible before fitting 1322K."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 1322K self-aligning ball bearing?",
        "a": "A 1322K self-aligning ball bearing has a 110 mm bore, 240 mm outer diameter and 50 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1322."
      },
      {
        "q": "How does the 1322 bore code work?",
        "a": "The last two digits of 1322 are bore code 22, giving 22 × 5 = 110 mm bore. The 240 mm outside diameter and 50 mm width follow the ISO 15 diameter series, not the bore code alone."
      },
      {
        "q": "What does the K suffix mean on 1322K?",
        "a": "The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1322. Adapter sleeves are sold separately and must match the bore code."
      },
      {
        "q": "How does the 1300 compare with other self-aligning series at the same 110 mm bore?",
        "a": "The 13xx is the medium section: 240×50 mm, 65.0 mm radial section at 110 mm bore, carrying more load than a 1222 but needing a larger housing bore."
      }
    ],
    "confidence_score": 0.7,
    "status": "published",
    "last_verified": "2026-09-25",
    "cross_ref": [
      {
        "equiv_sku": "1322K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ]
  },
  {
    "sku": "135-TN9",
    "brand": "SKF",
    "manufacturer_designation": "135 TN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 5,
    "D_mm": 19,
    "B_mm": 6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 2.51,
    "static_load_kN": 0.48,
    "fatigue_load_limit_kN": 0.025,
    "reference_speed_rpm": 63000,
    "limiting_speed_rpm": 45000,
    "max_rpm": 45000,
    "weight_g": 9,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the final digit of 135 is the bore in millimetres: 135 TN9 fits a 5 mm shaft (direct miniature spelling). Envelope 5×19×6 mm (0.197×0.748×0.236 in) with a 7.0 mm radial section height, C 2.51 kN, C0 0.48 kN and Pu 0.025 kN. The open 135 TN9 carries no shields or seals and relies on application lubrication and external sealing. The TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 5 mm shaft. Reference (thermal) speed 63000 r/min, limiting speed 45000 r/min, catalogue mass 9 g.",
    "applications": [
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 135-TN9 (C 2.51 kN, C0 0.48 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 135-TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The TN9 suffix on 135-TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 45000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 135-TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.025 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 5 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 135-TN9?",
        "a": "SKF 135 TN9 measures 5 mm bore × 19 mm OD × 6 mm width (0.197 × 0.748 × 0.236 in), mass about 9 g. It is open, with no shields or seals."
      },
      {
        "q": "How do I read the 135 designation?",
        "a": "Miniature self-aligning bearings print the bore as the final digit, so 135 is a 5 mm bearing; the leading digits give the section family."
      },
      {
        "q": "Can 135-TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 135-TN9?",
        "a": "With a rotating inner ring use roughly j5/k5 on the shaft and H7 in the 19 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "135",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "135-TN9",
      "135 TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "126-TN9",
    "brand": "SKF",
    "manufacturer_designation": "126 TN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 6,
    "D_mm": 19,
    "B_mm": 6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 2.51,
    "static_load_kN": 0.48,
    "fatigue_load_limit_kN": 0.025,
    "reference_speed_rpm": 70000,
    "limiting_speed_rpm": 45000,
    "max_rpm": 45000,
    "weight_g": 9,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the final digit of 126 is the bore in millimetres: 126 TN9 fits a 6 mm shaft (direct miniature spelling). Envelope 6×19×6 mm (0.236×0.748×0.236 in) with a 6.5 mm radial section height, C 2.51 kN, C0 0.48 kN and Pu 0.025 kN. The open 126 TN9 carries no shields or seals and relies on application lubrication and external sealing. The TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 6 mm shaft. Reference (thermal) speed 70000 r/min, limiting speed 45000 r/min, catalogue mass 9 g.",
    "applications": [
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 126-TN9 (C 2.51 kN, C0 0.48 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The fatigue load limit is 0.025 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The TN9 suffix on 126-TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 45000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 126-TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.025 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 6 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 126-TN9?",
        "a": "SKF 126 TN9 measures 6 mm bore × 19 mm OD × 6 mm width (0.236 × 0.748 × 0.236 in), mass about 9 g. It is open, with no shields or seals."
      },
      {
        "q": "How do I read the 126 designation?",
        "a": "Miniature self-aligning bearings print the bore as the final digit, so 126 is a 6 mm bearing; the leading digits give the section family."
      },
      {
        "q": "What is the speed rating of 126-TN9?",
        "a": "SKF lists a 70000 r/min thermal reference speed and a 45000 r/min mechanical limiting speed for 126 TN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 126-TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 126-TN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "126",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "126-TN9",
      "126 TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "127-TN9",
    "brand": "SKF",
    "manufacturer_designation": "127 TN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 7,
    "D_mm": 22,
    "B_mm": 7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 2.65,
    "static_load_kN": 0.56,
    "fatigue_load_limit_kN": 0.029,
    "reference_speed_rpm": 63000,
    "limiting_speed_rpm": 40000,
    "max_rpm": 40000,
    "weight_g": 14,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the final digit of 127 is the bore in millimetres: 127 TN9 fits a 7 mm shaft (direct miniature spelling). Envelope 7×22×7 mm (0.276×0.866×0.276 in) with a 7.5 mm radial section height, C 2.65 kN, C0 0.56 kN and Pu 0.029 kN. The open 127 TN9 carries no shields or seals and relies on application lubrication and external sealing. The TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 7 mm shaft. Reference (thermal) speed 63000 r/min, limiting speed 40000 r/min, catalogue mass 14 g.",
    "applications": [
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 7 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Assign interference to the rotating ring: on a 7 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The TN9 suffix on 127-TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 40000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 127-TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 7 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 127-TN9 (C 2.65 kN, C0 0.56 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 127-TN9?",
        "a": "SKF 127 TN9 measures 7 mm bore × 22 mm OD × 7 mm width (0.276 × 0.866 × 0.276 in), mass about 14 g. It is open, with no shields or seals."
      },
      {
        "q": "How do I read the 127 designation?",
        "a": "Miniature self-aligning bearings print the bore as the final digit, so 127 is a 7 mm bearing; the leading digits give the section family."
      },
      {
        "q": "Which fits should I use for 127-TN9?",
        "a": "With a rotating inner ring use roughly j5/k5 on the shaft and H7 in the 22 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 127-TN9?",
        "a": "Catalogue mass is 14 g for 127 TN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "127",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "127-TN9",
      "127 TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "108-TN9",
    "brand": "SKF",
    "manufacturer_designation": "108 TN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 8,
    "D_mm": 22,
    "B_mm": 7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 2.65,
    "static_load_kN": 0.56,
    "fatigue_load_limit_kN": 0.029,
    "reference_speed_rpm": 60000,
    "limiting_speed_rpm": 40000,
    "max_rpm": 40000,
    "weight_g": 14,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 10xx series is a self-aligning ball bearing family. the final digit of 108 is the bore in millimetres: 108 TN9 fits a 8 mm shaft (direct miniature spelling). Envelope 8×22×7 mm (0.315×0.866×0.276 in) with a 7.0 mm radial section height, C 2.65 kN, C0 0.56 kN and Pu 0.029 kN. The open 108 TN9 carries no shields or seals and relies on application lubrication and external sealing. The TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 8 mm shaft. Reference (thermal) speed 60000 r/min, limiting speed 40000 r/min, catalogue mass 14 g.",
    "applications": [
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 108-TN9 (C 2.65 kN, C0 0.56 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 108-TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The TN9 suffix on 108-TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 40000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 108-TN9 chamfer so the 7 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 108-TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 8 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 108-TN9?",
        "a": "SKF 108 TN9 measures 8 mm bore × 22 mm OD × 7 mm width (0.315 × 0.866 × 0.276 in), mass about 14 g. It is open, with no shields or seals."
      },
      {
        "q": "How do I read the 108 designation?",
        "a": "Miniature self-aligning bearings print the bore as the final digit, so 108 is a 8 mm bearing; the leading digits give the section family."
      },
      {
        "q": "What is the speed rating of 108-TN9?",
        "a": "SKF lists a 60000 r/min thermal reference speed and a 40000 r/min mechanical limiting speed for 108 TN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 108-TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 108-TN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "108",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "108-TN9",
      "108 TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "129-TN9",
    "brand": "SKF",
    "manufacturer_designation": "129 TN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 9,
    "D_mm": 26,
    "B_mm": 8,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 3.9,
    "static_load_kN": 0.82,
    "fatigue_load_limit_kN": 0.043,
    "reference_speed_rpm": 60000,
    "limiting_speed_rpm": 38000,
    "max_rpm": 38000,
    "weight_g": 22,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the final digit of 129 is the bore in millimetres: 129 TN9 fits a 9 mm shaft (direct miniature spelling). Envelope 9×26×8 mm (0.354×1.024×0.315 in) with a 8.5 mm radial section height, C 3.9 kN, C0 0.82 kN and Pu 0.043 kN. The open 129 TN9 carries no shields or seals and relies on application lubrication and external sealing. The TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 9 mm shaft. Reference (thermal) speed 60000 r/min, limiting speed 38000 r/min, catalogue mass 22 g.",
    "applications": [
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 129-TN9 chamfer so the 8 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Mount 129-TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The TN9 suffix on 129-TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 38000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 129-TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 129-TN9 chamfer so the 8 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 129-TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 129-TN9?",
        "a": "SKF 129 TN9 measures 9 mm bore × 26 mm OD × 8 mm width (0.354 × 1.024 × 0.315 in), mass about 22 g. It is open, with no shields or seals."
      },
      {
        "q": "How do I read the 129 designation?",
        "a": "Miniature self-aligning bearings print the bore as the final digit, so 129 is a 9 mm bearing; the leading digits give the section family."
      },
      {
        "q": "Which fits should I use for 129-TN9?",
        "a": "With a rotating inner ring use roughly j5/k5 on the shaft and H7 in the 26 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 129-TN9?",
        "a": "Catalogue mass is 22 g for 129 TN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "129",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "129-TN9",
      "129 TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1200-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1200 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 5.53,
    "static_load_kN": 1.18,
    "fatigue_load_limit_kN": 0.061,
    "reference_speed_rpm": 56000,
    "limiting_speed_rpm": 36000,
    "max_rpm": 36000,
    "weight_g": 34,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). bore code 00 follows the 10/12/15/17 mm exception table, so 1200 fits a 10 mm shaft. Envelope 10×30×9 mm (0.394×1.181×0.354 in) with a 10.0 mm radial section height, C 5.53 kN, C0 1.18 kN and Pu 0.061 kN. The open 1200 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 10 mm shaft. Reference (thermal) speed 56000 r/min, limiting speed 36000 r/min, catalogue mass 34 g.",
    "applications": [
      "fan and blower shafts",
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 1200-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Fillet radii must clear the 1200-ETN9 chamfer so the 9 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The ETN9 suffix on 1200-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 36000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 1200-ETN9 (C 5.53 kN, C0 1.18 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1200-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.061 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1200-ETN9?",
        "a": "SKF 1200 ETN9 measures 10 mm bore × 30 mm OD × 9 mm width (0.394 × 1.181 × 0.354 in), mass about 34 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1200 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 1200 fits a 10 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "What load can 1200-ETN9 take?",
        "a": "Catalogue values for 1200 ETN9: dynamic C 5.53 kN, static C0 1.18 kN, fatigue limit Pu 0.061 kN. Use C in life calculation and C0 for static checks at 10 mm bore."
      },
      {
        "q": "What is the speed rating of 1200-ETN9?",
        "a": "SKF lists a 56000 r/min thermal reference speed and a 36000 r/min mechanical limiting speed for 1200 ETN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1200",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1200-ETN9",
      "1200 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2200-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2200 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 5.53,
    "static_load_kN": 1.18,
    "fatigue_load_limit_kN": 0.06,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 48,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). bore code 00 follows the 10/12/15/17 mm exception table, so 2200 fits a 10 mm shaft. Envelope 10×30×14 mm (0.394×1.181×0.551 in) with a 10.0 mm radial section height, C 5.53 kN, C0 1.18 kN and Pu 0.06 kN. SKF spells the sealed execution 2200 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 10 mm shaft. Limiting speed 17000 r/min, catalogue mass 48 g.",
    "applications": [
      "fan and blower shafts",
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 10 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Fillet radii must clear the 2200-E-2RS1TN9 chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Do not wash 2200-E-2RS1TN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "The E-2RS1TN9 suffix on 2200-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 17000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2200-E-2RS1TN9 chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2200-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2200-E-2RS1TN9?",
        "a": "SKF 2200 E-2RS1TN9 measures 10 mm bore × 30 mm OD × 14 mm width (0.394 × 1.181 × 0.551 in), mass about 48 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2200 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 2200 fits a 10 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "Which fits should I use for 2200-E-2RS1TN9?",
        "a": "With a rotating inner ring use roughly j5/k5 on the shaft and H7 in the 30 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2200-E-2RS1TN9?",
        "a": "Catalogue mass is 48 g for 2200 E-2RS1TN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2200",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 10×30×14 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2200-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 10×30×14 mm envelope, but catalogue C/C0 differ between executions (5.53/1.18 kN vs 8.06/1.73 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2200-E-2RS1TN9",
      "2200 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2200-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2200 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 8.06,
    "static_load_kN": 1.73,
    "fatigue_load_limit_kN": 0.09,
    "reference_speed_rpm": 50000,
    "limiting_speed_rpm": 34000,
    "max_rpm": 34000,
    "weight_g": 47,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). bore code 00 follows the 10/12/15/17 mm exception table, so 2200 fits a 10 mm shaft. Envelope 10×30×14 mm (0.394×1.181×0.551 in) with a 10.0 mm radial section height, C 8.06 kN, C0 1.73 kN and Pu 0.09 kN. The open 2200 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 10 mm shaft. Reference (thermal) speed 50000 r/min, limiting speed 34000 r/min, catalogue mass 47 g.",
    "applications": [
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2200-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2200-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The ETN9 suffix on 2200-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 34000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2200-ETN9 chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2200-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 10 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2200-ETN9?",
        "a": "SKF 2200 ETN9 measures 10 mm bore × 30 mm OD × 14 mm width (0.394 × 1.181 × 0.551 in), mass about 47 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2200 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 2200 fits a 10 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "What is the speed rating of 2200-ETN9?",
        "a": "SKF lists a 50000 r/min thermal reference speed and a 34000 r/min mechanical limiting speed for 2200 ETN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 2200-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2200-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2200",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2200-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 10×30×14 mm envelope, but catalogue C/C0 differ between executions (8.06/1.73 kN vs 5.53/1.18 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2200-ETN9",
      "2200 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1201-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1201 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 10,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 6.24,
    "static_load_kN": 1.43,
    "fatigue_load_limit_kN": 0.072,
    "reference_speed_rpm": 50000,
    "limiting_speed_rpm": 32000,
    "max_rpm": 32000,
    "weight_g": 40,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). bore code 01 follows the 10/12/15/17 mm exception table, so 1201 fits a 12 mm shaft. Envelope 12×32×10 mm (0.472×1.26×0.394 in) with a 10.0 mm radial section height, C 6.24 kN, C0 1.43 kN and Pu 0.072 kN. The open 1201 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 12 mm shaft. Reference (thermal) speed 50000 r/min, limiting speed 32000 r/min, catalogue mass 40 g.",
    "applications": [
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 1201-ETN9 (C 6.24 kN, C0 1.43 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1201-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The ETN9 suffix on 1201-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 32000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 1201-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.072 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 12 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1201-ETN9?",
        "a": "SKF 1201 ETN9 measures 12 mm bore × 32 mm OD × 10 mm width (0.472 × 1.26 × 0.394 in), mass about 40 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1201 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 1201 fits a 12 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "What is the speed rating of 1201-ETN9?",
        "a": "SKF lists a 50000 r/min thermal reference speed and a 32000 r/min mechanical limiting speed for 1201 ETN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1201-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1201-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1201",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 12×32×10 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1201-ETN9",
      "1201 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2201-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2201 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 6.24,
    "static_load_kN": 1.43,
    "fatigue_load_limit_kN": 0.08,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "weight_g": 53,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). bore code 01 follows the 10/12/15/17 mm exception table, so 2201 fits a 12 mm shaft. Envelope 12×32×14 mm (0.472×1.26×0.551 in) with a 10.0 mm radial section height, C 6.24 kN, C0 1.43 kN and Pu 0.08 kN. SKF spells the sealed execution 2201 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 12 mm shaft. Limiting speed 16000 r/min, catalogue mass 53 g.",
    "applications": [
      "textile spindles and looms",
      "fan and blower shafts",
      "woodworking machine spindles",
      "light gearbox layshafts"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2201-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The spherical outer raceway lets 2201-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The 2RS1 contact seals on 2201-E-2RS1TN9 add drag and cap speed at 16000 r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "The E-2RS1TN9 suffix on 2201-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 16000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 2201-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2201-E-2RS1TN9 chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2201-E-2RS1TN9?",
        "a": "SKF 2201 E-2RS1TN9 measures 12 mm bore × 32 mm OD × 14 mm width (0.472 × 1.26 × 0.551 in), mass about 53 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2201 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 2201 fits a 12 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "Can 2201-E-2RS1TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2201-E-2RS1TN9?",
        "a": "With a rotating inner ring use roughly j5/k5 on the shaft and H7 in the 32 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2201",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 12×32×14 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2201-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 12×32×14 mm envelope, but catalogue C/C0 differ between executions (6.24/1.43 kN vs 8.52/1.9 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2201-E-2RS1TN9",
      "2201 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2201-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2201 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 8.52,
    "static_load_kN": 1.9,
    "fatigue_load_limit_kN": 0.098,
    "reference_speed_rpm": 45000,
    "limiting_speed_rpm": 30000,
    "max_rpm": 30000,
    "weight_g": 53,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). bore code 01 follows the 10/12/15/17 mm exception table, so 2201 fits a 12 mm shaft. Envelope 12×32×14 mm (0.472×1.26×0.551 in) with a 10.0 mm radial section height, C 8.52 kN, C0 1.9 kN and Pu 0.098 kN. The open 2201 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 12 mm shaft. Reference (thermal) speed 45000 r/min, limiting speed 30000 r/min, catalogue mass 53 g.",
    "applications": [
      "fan and blower shafts",
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2201-ETN9 chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Fillet radii must clear the 2201-ETN9 chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The ETN9 suffix on 2201-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 30000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 2201-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2201-ETN9 chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2201-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2201-ETN9?",
        "a": "SKF 2201 ETN9 measures 12 mm bore × 32 mm OD × 14 mm width (0.472 × 1.26 × 0.551 in), mass about 53 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2201 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 2201 fits a 12 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "What load can 2201-ETN9 take?",
        "a": "Catalogue values for 2201 ETN9: dynamic C 8.52 kN, static C0 1.9 kN, fatigue limit Pu 0.098 kN. Use C in life calculation and C0 for static checks at 12 mm bore."
      },
      {
        "q": "What is the speed rating of 2201-ETN9?",
        "a": "SKF lists a 45000 r/min thermal reference speed and a 30000 r/min mechanical limiting speed for 2201 ETN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2201",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2201-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 12×32×14 mm envelope, but catalogue C/C0 differ between executions (8.52/1.9 kN vs 6.24/1.43 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2201-ETN9",
      "2201 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1301-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1301 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 12,
    "D_mm": 37,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 9.36,
    "static_load_kN": 2.16,
    "fatigue_load_limit_kN": 0.12,
    "reference_speed_rpm": 40000,
    "limiting_speed_rpm": 28000,
    "max_rpm": 28000,
    "weight_g": 67,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). bore code 01 follows the 10/12/15/17 mm exception table, so 1301 fits a 12 mm shaft. Envelope 12×37×12 mm (0.472×1.457×0.472 in) with a 12.5 mm radial section height, C 9.36 kN, C0 2.16 kN and Pu 0.12 kN. The open 1301 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 12 mm shaft. Reference (thermal) speed 40000 r/min, limiting speed 28000 r/min, catalogue mass 67 g.",
    "applications": [
      "fan and blower shafts",
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 1301-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Fillet radii must clear the 1301-ETN9 chamfer so the 12 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The ETN9 suffix on 1301-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 28000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 1301-ETN9 (C 9.36 kN, C0 2.16 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1301-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.12 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1301-ETN9?",
        "a": "SKF 1301 ETN9 measures 12 mm bore × 37 mm OD × 12 mm width (0.472 × 1.457 × 0.472 in), mass about 67 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1301 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 1301 fits a 12 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "Which fits should I use for 1301-ETN9?",
        "a": "With a rotating inner ring use roughly j5/k5 on the shaft and H7 in the 37 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 1301-ETN9?",
        "a": "Catalogue mass is 67 g for 1301 ETN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1301",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1301-ETN9",
      "1301 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1202-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1202 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 7.41,
    "static_load_kN": 1.76,
    "fatigue_load_limit_kN": 0.09,
    "reference_speed_rpm": 45000,
    "limiting_speed_rpm": 28000,
    "max_rpm": 28000,
    "weight_g": 49,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). bore code 02 follows the 10/12/15/17 mm exception table, so 1202 fits a 15 mm shaft. Envelope 15×35×11 mm (0.591×1.378×0.433 in) with a 10.0 mm radial section height, C 7.41 kN, C0 1.76 kN and Pu 0.09 kN. The open 1202 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 15 mm shaft. Reference (thermal) speed 45000 r/min, limiting speed 28000 r/min, catalogue mass 49 g.",
    "applications": [
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 15 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Assign interference to the rotating ring: on a 15 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The ETN9 suffix on 1202-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 28000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1202-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 15 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 1202-ETN9 (C 7.41 kN, C0 1.76 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1202-ETN9?",
        "a": "SKF 1202 ETN9 measures 15 mm bore × 35 mm OD × 11 mm width (0.591 × 1.378 × 0.433 in), mass about 49 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1202 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 1202 fits a 15 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "How much misalignment can 1202-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1202-ETN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 1202-ETN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1202",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1202-ETN9",
      "1202 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2202-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2202 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 7.41,
    "static_load_kN": 1.76,
    "fatigue_load_limit_kN": 0.09,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 58,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). bore code 02 follows the 10/12/15/17 mm exception table, so 2202 fits a 15 mm shaft. Envelope 15×35×14 mm (0.591×1.378×0.551 in) with a 10.0 mm radial section height, C 7.41 kN, C0 1.76 kN and Pu 0.09 kN. SKF spells the sealed execution 2202 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 15 mm shaft. Limiting speed 14000 r/min, catalogue mass 58 g.",
    "applications": [
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 2202-E-2RS1TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Assign interference to the rotating ring: on a 15 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2202-E-2RS1TN9 to avoid seal-lip binding.",
      "The E-2RS1TN9 suffix on 2202-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 14000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 15 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 2202-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2202-E-2RS1TN9?",
        "a": "SKF 2202 E-2RS1TN9 measures 15 mm bore × 35 mm OD × 14 mm width (0.591 × 1.378 × 0.551 in), mass about 58 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2202 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 2202 fits a 15 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "How much misalignment can 2202-E-2RS1TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2202-E-2RS1TN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2202-E-2RS1TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2202",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×35×14 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2202-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×14 mm envelope, but catalogue C/C0 differ between executions (7.41/1.76 kN vs 8.71/2.04 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2202-E-2RS1TN9",
      "2202 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2202-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2202 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 8.71,
    "static_load_kN": 2.04,
    "fatigue_load_limit_kN": 0.11,
    "reference_speed_rpm": 38000,
    "limiting_speed_rpm": 26000,
    "max_rpm": 26000,
    "weight_g": 60,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). bore code 02 follows the 10/12/15/17 mm exception table, so 2202 fits a 15 mm shaft. Envelope 15×35×14 mm (0.591×1.378×0.551 in) with a 10.0 mm radial section height, C 8.71 kN, C0 2.04 kN and Pu 0.11 kN. The open 2202 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 15 mm shaft. Reference (thermal) speed 38000 r/min, limiting speed 26000 r/min, catalogue mass 60 g.",
    "applications": [
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.11 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Catalogue ratings for 2202-ETN9 (C 8.71 kN, C0 2.04 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The ETN9 suffix on 2202-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 26000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 15 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 2202-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2202-ETN9 chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2202-ETN9?",
        "a": "SKF 2202 ETN9 measures 15 mm bore × 35 mm OD × 14 mm width (0.591 × 1.378 × 0.551 in), mass about 60 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2202 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 2202 fits a 15 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "What is the speed rating of 2202-ETN9?",
        "a": "SKF lists a 38000 r/min thermal reference speed and a 26000 r/min mechanical limiting speed for 2202 ETN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 2202-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2202-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2202",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×35×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2202-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×14 mm envelope, but catalogue C/C0 differ between executions (8.71/2.04 kN vs 7.41/1.76 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2202-ETN9",
      "2202 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1302-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1302 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 13,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 10.8,
    "static_load_kN": 2.6,
    "fatigue_load_limit_kN": 0.14,
    "reference_speed_rpm": 34000,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "weight_g": 94,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). bore code 02 follows the 10/12/15/17 mm exception table, so 1302 fits a 15 mm shaft. Envelope 15×42×13 mm (0.591×1.654×0.512 in) with a 13.5 mm radial section height, C 10.8 kN, C0 2.6 kN and Pu 0.14 kN. The open 1302 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 15 mm shaft. Reference (thermal) speed 34000 r/min, limiting speed 24000 r/min, catalogue mass 94 g.",
    "applications": [
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1302-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Catalogue ratings for 1302-ETN9 (C 10.8 kN, C0 2.6 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The ETN9 suffix on 1302-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 24000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 15 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 1302-ETN9 (C 10.8 kN, C0 2.6 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1302-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1302-ETN9?",
        "a": "SKF 1302 ETN9 measures 15 mm bore × 42 mm OD × 13 mm width (0.591 × 1.654 × 0.512 in), mass about 94 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1302 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 1302 fits a 15 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "What is the speed rating of 1302-ETN9?",
        "a": "SKF lists a 34000 r/min thermal reference speed and a 24000 r/min mechanical limiting speed for 1302 ETN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1302-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1302-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1302",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×42×13 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1302-ETN9",
      "1302 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2302-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2302 E-2RS1TN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 10.8,
    "static_load_kN": 2.6,
    "fatigue_load_limit_kN": 0.14,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). bore code 02 follows the 10/12/15/17 mm exception table, so 2302 fits a 15 mm shaft. Envelope 15×42×17 mm (0.591×1.654×0.669 in) with a 13.5 mm radial section height, C 10.8 kN, C0 2.6 kN and Pu 0.14 kN. SKF spells the sealed execution 2302 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 15 mm shaft. Limiting speed 12000 r/min, catalogue mass 110 g.",
    "applications": [
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.14 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2302-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The 2RS1 contact seals on 2302-E-2RS1TN9 add drag and cap speed at 12000 r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "The E-2RS1TN9 suffix on 2302-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 12000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.14 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 15 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2302-E-2RS1TN9?",
        "a": "SKF 2302 E-2RS1TN9 measures 15 mm bore × 42 mm OD × 17 mm width (0.591 × 1.654 × 0.669 in), mass about 110 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2302 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 2302 fits a 15 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "Can 2302-E-2RS1TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2302-E-2RS1TN9?",
        "a": "With a rotating inner ring use roughly j5/k5 on the shaft and H7 in the 42 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2302",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×42×17 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2302-E-2RS1TN9",
      "2302 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1203-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1203 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 8.84,
    "static_load_kN": 2.2,
    "fatigue_load_limit_kN": 0.12,
    "reference_speed_rpm": 38000,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "weight_g": 73,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). bore code 03 follows the 10/12/15/17 mm exception table, so 1203 fits a 17 mm shaft. Envelope 17×40×12 mm (0.669×1.575×0.472 in) with a 11.5 mm radial section height, C 8.84 kN, C0 2.2 kN and Pu 0.12 kN. The open 1203 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 17 mm shaft. Reference (thermal) speed 38000 r/min, limiting speed 24000 r/min, catalogue mass 73 g.",
    "applications": [
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1203-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Catalogue ratings for 1203-ETN9 (C 8.84 kN, C0 2.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The ETN9 suffix on 1203-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 24000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 17 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 1203-ETN9 (C 8.84 kN, C0 2.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1203-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1203-ETN9?",
        "a": "SKF 1203 ETN9 measures 17 mm bore × 40 mm OD × 12 mm width (0.669 × 1.575 × 0.472 in), mass about 73 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1203 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 1203 fits a 17 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "What is the speed rating of 1203-ETN9?",
        "a": "SKF lists a 38000 r/min thermal reference speed and a 24000 r/min mechanical limiting speed for 1203 ETN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1203-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1203-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1203",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1203-ETN9",
      "1203 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2203-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2203 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 8.84,
    "static_load_kN": 2.2,
    "fatigue_load_limit_kN": 0.12,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 89,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). bore code 03 follows the 10/12/15/17 mm exception table, so 2203 fits a 17 mm shaft. Envelope 17×40×16 mm (0.669×1.575×0.63 in) with a 11.5 mm radial section height, C 8.84 kN, C0 2.2 kN and Pu 0.12 kN. SKF spells the sealed execution 2203 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 17 mm shaft. Limiting speed 12000 r/min, catalogue mass 89 g.",
    "applications": [
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.12 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2203-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The 2RS1 contact seals on 2203-E-2RS1TN9 add drag and cap speed at 12000 r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "The E-2RS1TN9 suffix on 2203-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 12000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.12 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 17 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2203-E-2RS1TN9?",
        "a": "SKF 2203 E-2RS1TN9 measures 17 mm bore × 40 mm OD × 16 mm width (0.669 × 1.575 × 0.63 in), mass about 89 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2203 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 2203 fits a 17 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "Can 2203-E-2RS1TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2203-E-2RS1TN9?",
        "a": "With a rotating inner ring use roughly j5/k5 on the shaft and H7 in the 40 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2203",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×40×16 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2203-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×16 mm envelope, but catalogue C/C0 differ between executions (8.84/2.2 kN vs 10.6/2.55 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2203-E-2RS1TN9",
      "2203 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2203-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2203 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 10.6,
    "static_load_kN": 2.55,
    "fatigue_load_limit_kN": 0.14,
    "reference_speed_rpm": 34000,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "weight_g": 88,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). bore code 03 follows the 10/12/15/17 mm exception table, so 2203 fits a 17 mm shaft. Envelope 17×40×16 mm (0.669×1.575×0.63 in) with a 11.5 mm radial section height, C 10.6 kN, C0 2.55 kN and Pu 0.14 kN. The open 2203 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 17 mm shaft. Reference (thermal) speed 34000 r/min, limiting speed 24000 r/min, catalogue mass 88 g.",
    "applications": [
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 17 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Assign interference to the rotating ring: on a 17 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The ETN9 suffix on 2203-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 24000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.14 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 17 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 2203-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2203-ETN9?",
        "a": "SKF 2203 ETN9 measures 17 mm bore × 40 mm OD × 16 mm width (0.669 × 1.575 × 0.63 in), mass about 88 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2203 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 2203 fits a 17 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "How much misalignment can 2203-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2203-ETN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2203-ETN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2203",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2203-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×16 mm envelope, but catalogue C/C0 differ between executions (10.6/2.55 kN vs 8.84/2.2 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2203-ETN9",
      "2203 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1303-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1303 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 3.4,
    "fatigue_load_limit_kN": 0.18,
    "reference_speed_rpm": 28000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 120,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). bore code 03 follows the 10/12/15/17 mm exception table, so 1303 fits a 17 mm shaft. Envelope 17×47×14 mm (0.669×1.85×0.551 in) with a 15.0 mm radial section height, C 12.7 kN, C0 3.4 kN and Pu 0.18 kN. The open 1303 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 17 mm shaft. Reference (thermal) speed 28000 r/min, limiting speed 20000 r/min, catalogue mass 120 g.",
    "applications": [
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 17 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Assign interference to the rotating ring: on a 17 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The ETN9 suffix on 1303-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 20000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1303-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 17 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 1303-ETN9 (C 12.7 kN, C0 3.4 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1303-ETN9?",
        "a": "SKF 1303 ETN9 measures 17 mm bore × 47 mm OD × 14 mm width (0.669 × 1.85 × 0.551 in), mass about 120 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1303 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 1303 fits a 17 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "How much misalignment can 1303-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1303-ETN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 1303-ETN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1303",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1303-ETN9",
      "1303 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2303-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2303 E-2RS1TN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 3.4,
    "fatigue_load_limit_kN": 0.18,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). bore code 03 follows the 10/12/15/17 mm exception table, so 2303 fits a 17 mm shaft. Envelope 17×47×19 mm (0.669×1.85×0.748 in) with a 15.0 mm radial section height, C 12.7 kN, C0 3.4 kN and Pu 0.18 kN. SKF spells the sealed execution 2303 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 17 mm shaft. Limiting speed 11000 r/min, catalogue mass 160 g.",
    "applications": [
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 2303-E-2RS1TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Assign interference to the rotating ring: on a 17 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2303-E-2RS1TN9 to avoid seal-lip binding.",
      "The E-2RS1TN9 suffix on 2303-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 11000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 17 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 2303-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2303-E-2RS1TN9?",
        "a": "SKF 2303 E-2RS1TN9 measures 17 mm bore × 47 mm OD × 19 mm width (0.669 × 1.85 × 0.748 in), mass about 160 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2303 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 2303 fits a 17 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "How much misalignment can 2303-E-2RS1TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2303-E-2RS1TN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2303-E-2RS1TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2303",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×47×19 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2303-M",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×19 mm envelope, but catalogue C/C0 differ between executions (12.7/3.4 kN vs 14.3/3.55 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2303-E-2RS1TN9",
      "2303 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2303-M",
    "brand": "SKF",
    "manufacturer_designation": "2303 M",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 3.55,
    "fatigue_load_limit_kN": 0.19,
    "reference_speed_rpm": 30000,
    "limiting_speed_rpm": 22000,
    "max_rpm": 22000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). bore code 03 follows the 10/12/15/17 mm exception table, so 2303 fits a 17 mm shaft. Envelope 17×47×19 mm (0.669×1.85×0.748 in) with a 15.0 mm radial section height, C 14.3 kN, C0 3.55 kN and Pu 0.19 kN. The open 2303 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution. The bore is cylindrical (straight), for a press-fit on a 17 mm shaft. Reference (thermal) speed 30000 r/min, limiting speed 22000 r/min, catalogue mass 180 g.",
    "applications": [
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts",
      "woodworking machine spindles"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2303-M chamfer so the 19 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "At 17 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The M suffix on 2303-M denotes a machined brass cage: the choice for high speeds, marginal lubrication and shock/vibration duty, and temperature-tolerant where polymer cages are not.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2303-M (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 17 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2303-M (C 14.3 kN, C0 3.55 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2303-M?",
        "a": "SKF 2303 M measures 17 mm bore × 47 mm OD × 19 mm width (0.669 × 1.85 × 0.748 in), mass about 180 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2303 work?",
        "a": "Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 2303 fits a 17 mm shaft. Code × 5 starts at code 04."
      },
      {
        "q": "What load can 2303-M take?",
        "a": "Catalogue values for 2303 M: dynamic C 14.3 kN, static C0 3.55 kN, fatigue limit Pu 0.19 kN. Use C in life calculation and C0 for static checks at 17 mm bore."
      },
      {
        "q": "What is the speed rating of 2303-M?",
        "a": "SKF lists a 30000 r/min thermal reference speed and a 22000 r/min mechanical limiting speed for 2303 M; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2303",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2303-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×19 mm envelope, but catalogue C/C0 differ between executions (14.3/3.55 kN vs 12.7/3.4 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2303-M",
      "2303 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1204-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1204 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 3.4,
    "fatigue_load_limit_kN": 0.18,
    "reference_speed_rpm": 32000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 120,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1204 carries code 04 = 20 mm (code × 5). Envelope 20×47×14 mm (0.787×1.85×0.551 in) with a 13.5 mm radial section height, C 12.7 kN, C0 3.4 kN and Pu 0.18 kN. The open 1204 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 20 mm shaft. Reference (thermal) speed 32000 r/min, limiting speed 20000 r/min, catalogue mass 120 g.",
    "applications": [
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 1204-ETN9 chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Mount 1204-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The ETN9 suffix on 1204-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 20000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 1204-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 1204-ETN9 chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1204-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1204-ETN9?",
        "a": "SKF 1204 ETN9 measures 20 mm bore × 47 mm OD × 14 mm width (0.787 × 1.85 × 0.551 in), mass about 120 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1204 work?",
        "a": "The final two digits of 1204 are bore code 04, multiplied by 5 to give 20 mm."
      },
      {
        "q": "What load can 1204-ETN9 take?",
        "a": "Catalogue values for 1204 ETN9: dynamic C 12.7 kN, static C0 3.4 kN, fatigue limit Pu 0.18 kN. Use C in life calculation and C0 for static checks at 20 mm bore."
      },
      {
        "q": "What is the speed rating of 1204-ETN9?",
        "a": "SKF lists a 32000 r/min thermal reference speed and a 20000 r/min mechanical limiting speed for 1204 ETN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1204",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1204-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 1204 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11204-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 11204 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1204-ETN9",
      "1204 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1204-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1204 EKTN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 3.4,
    "fatigue_load_limit_kN": 0.18,
    "reference_speed_rpm": 32000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 120,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1204 carries code 04 = 20 mm (code × 5). Envelope 20×47×14 mm (0.787×1.85×0.551 in) with a 13.5 mm radial section height, C 12.7 kN, C0 3.4 kN and Pu 0.18 kN. The open 1204 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 32000 r/min, limiting speed 20000 r/min, catalogue mass 120 g.",
    "applications": [
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1204-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1204-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The EKTN9 suffix on 1204-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 20000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.18 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 20 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1204-EKTN9?",
        "a": "SKF 1204 EKTN9 measures 20 mm bore × 47 mm OD × 14 mm width (0.787 × 1.85 × 0.551 in), mass about 120 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1204 work?",
        "a": "The final two digits of 1204 are bore code 04, multiplied by 5 to give 20 mm."
      },
      {
        "q": "Can 1204-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 1204-EKTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 47 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1204",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1204-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 1204 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11204-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 11204 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1204-EKTN9",
      "1204 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2204-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2204 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 3.4,
    "fatigue_load_limit_kN": 0.18,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2204 carries code 04 = 20 mm (code × 5). Envelope 20×47×18 mm (0.787×1.85×0.709 in) with a 13.5 mm radial section height, C 12.7 kN, C0 3.4 kN and Pu 0.18 kN. SKF spells the sealed execution 2204 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 20 mm shaft. Limiting speed 10000 r/min, catalogue mass 140 g.",
    "applications": [
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 20 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Mount 2204-E-2RS1TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Do not wash 2204-E-2RS1TN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "The E-2RS1TN9 suffix on 2204-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 10000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 2204-E-2RS1TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.18 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2204-E-2RS1TN9?",
        "a": "SKF 2204 E-2RS1TN9 measures 20 mm bore × 47 mm OD × 18 mm width (0.787 × 1.85 × 0.709 in), mass about 140 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2204 work?",
        "a": "The final two digits of 2204 are bore code 04, multiplied by 5 to give 20 mm."
      },
      {
        "q": "Which fits should I use for 2204-E-2RS1TN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 47 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2204-E-2RS1TN9?",
        "a": "Catalogue mass is 140 g for 2204 E-2RS1TN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2204",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×47×18 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2204-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×18 mm envelope, but catalogue C/C0 differ between executions (12.7/3.4 kN vs 16.8/4.15 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2204-E-2RS1TN9",
      "2204 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2204-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2204 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 16.8,
    "static_load_kN": 4.15,
    "fatigue_load_limit_kN": 0.22,
    "reference_speed_rpm": 28000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2204 carries code 04 = 20 mm (code × 5). Envelope 20×47×18 mm (0.787×1.85×0.709 in) with a 13.5 mm radial section height, C 16.8 kN, C0 4.15 kN and Pu 0.22 kN. The open 2204 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 20 mm shaft. Reference (thermal) speed 28000 r/min, limiting speed 20000 r/min, catalogue mass 140 g.",
    "applications": [
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 2204-ETN9 (C 16.8 kN, C0 4.15 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The fatigue load limit is 0.22 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The ETN9 suffix on 2204-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 20000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 2204-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.22 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 20 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2204-ETN9?",
        "a": "SKF 2204 ETN9 measures 20 mm bore × 47 mm OD × 18 mm width (0.787 × 1.85 × 0.709 in), mass about 140 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2204 work?",
        "a": "The final two digits of 2204 are bore code 04, multiplied by 5 to give 20 mm."
      },
      {
        "q": "Can 2204-ETN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2204-ETN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 47 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2204",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×47×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2204-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×18 mm envelope, but catalogue C/C0 differ between executions (16.8/4.15 kN vs 12.7/3.4 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2204-ETN9",
      "2204 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1304-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1304 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 4,
    "fatigue_load_limit_kN": 0.21,
    "reference_speed_rpm": 26000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1304 carries code 04 = 20 mm (code × 5). Envelope 20×52×15 mm (0.787×2.047×0.591 in) with a 16.0 mm radial section height, C 14.3 kN, C0 4 kN and Pu 0.21 kN. The open 1304 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 20 mm shaft. Reference (thermal) speed 26000 r/min, limiting speed 18000 r/min, catalogue mass 160 g.",
    "applications": [
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 1304-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The fatigue load limit is 0.21 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The ETN9 suffix on 1304-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 18000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 1304-ETN9 chamfer so the 15 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1304-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 20 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1304-ETN9?",
        "a": "SKF 1304 ETN9 measures 20 mm bore × 52 mm OD × 15 mm width (0.787 × 2.047 × 0.591 in), mass about 160 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1304 work?",
        "a": "The final two digits of 1304 are bore code 04, multiplied by 5 to give 20 mm."
      },
      {
        "q": "How heavy is 1304-ETN9?",
        "a": "Catalogue mass is 160 g for 1304 ETN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 1304-ETN9 take?",
        "a": "Catalogue values for 1304 ETN9: dynamic C 14.3 kN, static C0 4 kN, fatigue limit Pu 0.21 kN. Use C in life calculation and C0 for static checks at 20 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1304",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1304-ETN9",
      "1304 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2304-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2304 E-2RS1TN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 4,
    "fatigue_load_limit_kN": 0.21,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 210,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2304 carries code 04 = 20 mm (code × 5). Envelope 20×52×21 mm (0.787×2.047×0.827 in) with a 16.0 mm radial section height, C 14.3 kN, C0 4 kN and Pu 0.21 kN. SKF spells the sealed execution 2304 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 20 mm shaft. Limiting speed 9000 r/min, catalogue mass 210 g.",
    "applications": [
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 2304-E-2RS1TN9 (C 14.3 kN, C0 4 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Catalogue ratings for 2304-E-2RS1TN9 (C 14.3 kN, C0 4 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Do not wash 2304-E-2RS1TN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "The E-2RS1TN9 suffix on 2304-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 2304-E-2RS1TN9 (C 14.3 kN, C0 4 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 2304-E-2RS1TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2304-E-2RS1TN9?",
        "a": "SKF 2304 E-2RS1TN9 measures 20 mm bore × 52 mm OD × 21 mm width (0.787 × 2.047 × 0.827 in), mass about 210 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2304 work?",
        "a": "The final two digits of 2304 are bore code 04, multiplied by 5 to give 20 mm."
      },
      {
        "q": "What is the speed rating of 2304-E-2RS1TN9?",
        "a": "SKF publishes only the 9000 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      },
      {
        "q": "How much misalignment can 2304-E-2RS1TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2304-E-2RS1TN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2304",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×52×21 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2304-TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×21 mm envelope, but catalogue C/C0 differ between executions (14.3/4 kN vs 18.2/4.75 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2304-E-2RS1TN9",
      "2304 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2304-TN9",
    "brand": "SKF",
    "manufacturer_designation": "2304 TN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 18.2,
    "static_load_kN": 4.75,
    "fatigue_load_limit_kN": 0.24,
    "reference_speed_rpm": 26000,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "weight_g": 220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2304 carries code 04 = 20 mm (code × 5). Envelope 20×52×21 mm (0.787×2.047×0.827 in) with a 16.0 mm radial section height, C 18.2 kN, C0 4.75 kN and Pu 0.24 kN. The open 2304 TN9 carries no shields or seals and relies on application lubrication and external sealing. The TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 20 mm shaft. Reference (thermal) speed 26000 r/min, limiting speed 19000 r/min, catalogue mass 220 g.",
    "applications": [
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.24 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The fatigue load limit is 0.24 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The TN9 suffix on 2304-TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 19000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2304-TN9 chamfer so the 21 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2304-TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 20 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2304-TN9?",
        "a": "SKF 2304 TN9 measures 20 mm bore × 52 mm OD × 21 mm width (0.787 × 2.047 × 0.827 in), mass about 220 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2304 work?",
        "a": "The final two digits of 2304 are bore code 04, multiplied by 5 to give 20 mm."
      },
      {
        "q": "How heavy is 2304-TN9?",
        "a": "Catalogue mass is 220 g for 2304 TN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2304-TN9 take?",
        "a": "Catalogue values for 2304 TN9: dynamic C 18.2 kN, static C0 4.75 kN, fatigue limit Pu 0.24 kN. Use C in life calculation and C0 for static checks at 20 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2304",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2304-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×21 mm envelope, but catalogue C/C0 differ between executions (18.2/4.75 kN vs 14.3/4 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2304-TN9",
      "2304 TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1205-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1205 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 4,
    "fatigue_load_limit_kN": 0.21,
    "reference_speed_rpm": 28000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1205 carries code 05 = 25 mm (code × 5). Envelope 25×52×15 mm (0.984×2.047×0.591 in) with a 13.5 mm radial section height, C 14.3 kN, C0 4 kN and Pu 0.21 kN. The open 1205 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 25 mm shaft. Reference (thermal) speed 28000 r/min, limiting speed 18000 r/min, catalogue mass 140 g.",
    "applications": [
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 1205-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The fatigue load limit is 0.21 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The ETN9 suffix on 1205-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 18000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 1205-ETN9 chamfer so the 15 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1205-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 25 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1205-ETN9?",
        "a": "SKF 1205 ETN9 measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 140 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1205 work?",
        "a": "The final two digits of 1205 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "What is the speed rating of 1205-ETN9?",
        "a": "SKF lists a 28000 r/min thermal reference speed and a 18000 r/min mechanical limiting speed for 1205 ETN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1205-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1205-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1205",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1205-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 1205 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11205-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 11205 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1205-ETN9",
      "1205 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1205-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1205 EKTN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 4,
    "fatigue_load_limit_kN": 0.21,
    "reference_speed_rpm": 28000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1205 carries code 05 = 25 mm (code × 5). Envelope 25×52×15 mm (0.984×2.047×0.591 in) with a 13.5 mm radial section height, C 14.3 kN, C0 4 kN and Pu 0.21 kN. The open 1205 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 28000 r/min, limiting speed 18000 r/min, catalogue mass 140 g.",
    "applications": [
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts",
      "woodworking machine spindles"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 1205-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "At 25 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The EKTN9 suffix on 1205-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 18000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 25 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 1205-EKTN9 (C 14.3 kN, C0 4 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1205-EKTN9?",
        "a": "SKF 1205 EKTN9 measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 140 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1205 work?",
        "a": "The final two digits of 1205 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "What load can 1205-EKTN9 take?",
        "a": "Catalogue values for 1205 EKTN9: dynamic C 14.3 kN, static C0 4 kN, fatigue limit Pu 0.21 kN. Use C in life calculation and C0 for static checks at 25 mm bore."
      },
      {
        "q": "What is the speed rating of 1205-EKTN9?",
        "a": "SKF lists a 28000 r/min thermal reference speed and a 18000 r/min mechanical limiting speed for 1205 EKTN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1205",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1205-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 1205 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11205-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 11205 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1205-EKTN9",
      "1205 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2205-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2205 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 4,
    "fatigue_load_limit_kN": 0.21,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2205 carries code 05 = 25 mm (code × 5). Envelope 25×52×18 mm (0.984×2.047×0.709 in) with a 13.5 mm radial section height, C 14.3 kN, C0 4 kN and Pu 0.21 kN. SKF spells the sealed execution 2205 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 25 mm shaft. Limiting speed 9000 r/min, catalogue mass 160 g.",
    "applications": [
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 2205-E-2RS1TN9 (C 14.3 kN, C0 4 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Catalogue ratings for 2205-E-2RS1TN9 (C 14.3 kN, C0 4 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2205-E-2RS1TN9 to avoid seal-lip binding.",
      "The E-2RS1TN9 suffix on 2205-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 2205-E-2RS1TN9 (C 14.3 kN, C0 4 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 2205-E-2RS1TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2205-E-2RS1TN9?",
        "a": "SKF 2205 E-2RS1TN9 measures 25 mm bore × 52 mm OD × 18 mm width (0.984 × 2.047 × 0.709 in), mass about 160 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2205 work?",
        "a": "The final two digits of 2205 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "How heavy is 2205-E-2RS1TN9?",
        "a": "Catalogue mass is 160 g for 2205 E-2RS1TN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2205-E-2RS1TN9 take?",
        "a": "Catalogue values for 2205 E-2RS1TN9: dynamic C 14.3 kN, static C0 4 kN, fatigue limit Pu 0.21 kN. Use C in life calculation and C0 for static checks at 25 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2205",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2205-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×18 mm envelope with catalogue ratings within 10 %; 2205 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2205-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope, but catalogue C/C0 differ between executions (14.3/4 kN vs 16.8/4.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2205-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope, but catalogue C/C0 differ between executions (14.3/4 kN vs 16.8/4.4 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2205-E-2RS1TN9",
      "2205 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2205-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2205 E-2RS1KTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 4,
    "fatigue_load_limit_kN": 0.21,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2205 carries code 05 = 25 mm (code × 5). Envelope 25×52×18 mm (0.984×2.047×0.709 in) with a 13.5 mm radial section height, C 14.3 kN, C0 4 kN and Pu 0.21 kN. SKF spells the sealed execution 2205 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 9000 r/min, catalogue mass 160 g.",
    "applications": [
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2205-E-2RS1KTN9 chamfer so the 18 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Mount 2205-E-2RS1KTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Do not wash 2205-E-2RS1KTN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "On a sleeve-mounted 2205-E-2RS1KTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The E-2RS1KTN9 suffix on 2205-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.21 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2205-E-2RS1KTN9?",
        "a": "SKF 2205 E-2RS1KTN9 measures 25 mm bore × 52 mm OD × 18 mm width (0.984 × 2.047 × 0.709 in), mass about 160 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2205 work?",
        "a": "The final two digits of 2205 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "Which fits should I use for 2205-E-2RS1KTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 52 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2205-E-2RS1KTN9?",
        "a": "Catalogue mass is 160 g for 2205 E-2RS1KTN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2205",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2205-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×18 mm envelope with catalogue ratings within 10 %; 2205 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2205-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope, but catalogue C/C0 differ between executions (14.3/4 kN vs 16.8/4.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2205-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope, but catalogue C/C0 differ between executions (14.3/4 kN vs 16.8/4.4 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2205-E-2RS1KTN9",
      "2205 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2205-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2205 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 16.8,
    "static_load_kN": 4.4,
    "fatigue_load_limit_kN": 0.23,
    "reference_speed_rpm": 26000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2205 carries code 05 = 25 mm (code × 5). Envelope 25×52×18 mm (0.984×2.047×0.709 in) with a 13.5 mm radial section height, C 16.8 kN, C0 4.4 kN and Pu 0.23 kN. The open 2205 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 25 mm shaft. Reference (thermal) speed 26000 r/min, limiting speed 18000 r/min, catalogue mass 160 g.",
    "applications": [
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 2205-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Mount 2205-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The ETN9 suffix on 2205-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 18000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 2205-ETN9 (C 16.8 kN, C0 4.4 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 2205-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.23 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2205-ETN9?",
        "a": "SKF 2205 ETN9 measures 25 mm bore × 52 mm OD × 18 mm width (0.984 × 2.047 × 0.709 in), mass about 160 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2205 work?",
        "a": "The final two digits of 2205 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "What load can 2205-ETN9 take?",
        "a": "Catalogue values for 2205 ETN9: dynamic C 16.8 kN, static C0 4.4 kN, fatigue limit Pu 0.23 kN. Use C in life calculation and C0 for static checks at 25 mm bore."
      },
      {
        "q": "What is the speed rating of 2205-ETN9?",
        "a": "SKF lists a 26000 r/min thermal reference speed and a 18000 r/min mechanical limiting speed for 2205 ETN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2205",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2205-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope, but catalogue C/C0 differ between executions (16.8/4.4 kN vs 14.3/4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2205-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope, but catalogue C/C0 differ between executions (16.8/4.4 kN vs 14.3/4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2205-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×18 mm envelope with catalogue ratings within 10 %; 2205 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2205-ETN9",
      "2205 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2205-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2205 EKTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 16.8,
    "static_load_kN": 4.4,
    "fatigue_load_limit_kN": 0.23,
    "reference_speed_rpm": 26000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2205 carries code 05 = 25 mm (code × 5). Envelope 25×52×18 mm (0.984×2.047×0.709 in) with a 13.5 mm radial section height, C 16.8 kN, C0 4.4 kN and Pu 0.23 kN. The open 2205 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 26000 r/min, limiting speed 18000 r/min, catalogue mass 160 g.",
    "applications": [
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.23 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2205-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "On a sleeve-mounted 2205-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 2205-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 18000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2205-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 25 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2205-EKTN9?",
        "a": "SKF 2205 EKTN9 measures 25 mm bore × 52 mm OD × 18 mm width (0.984 × 2.047 × 0.709 in), mass about 160 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2205 work?",
        "a": "The final two digits of 2205 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "What is the speed rating of 2205-EKTN9?",
        "a": "SKF lists a 26000 r/min thermal reference speed and a 18000 r/min mechanical limiting speed for 2205 EKTN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 2205-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2205-EKTN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2205",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2205-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope, but catalogue C/C0 differ between executions (16.8/4.4 kN vs 14.3/4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2205-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×18 mm envelope, but catalogue C/C0 differ between executions (16.8/4.4 kN vs 14.3/4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2205-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×18 mm envelope with catalogue ratings within 10 %; 2205 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2205-EKTN9",
      "2205 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1305-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1305 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19,
    "static_load_kN": 5.4,
    "fatigue_load_limit_kN": 0.28,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 260,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1305 carries code 05 = 25 mm (code × 5). Envelope 25×62×17 mm (0.984×2.441×0.669 in) with a 18.5 mm radial section height, C 19 kN, C0 5.4 kN and Pu 0.28 kN. The open 1305 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 25 mm shaft. Reference (thermal) speed 22000 r/min, limiting speed 15000 r/min, catalogue mass 260 g.",
    "applications": [
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 1305-ETN9 chamfer so the 17 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Mount 1305-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The ETN9 suffix on 1305-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 15000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 1305-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 1305-ETN9 chamfer so the 17 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1305-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1305-ETN9?",
        "a": "SKF 1305 ETN9 measures 25 mm bore × 62 mm OD × 17 mm width (0.984 × 2.441 × 0.669 in), mass about 260 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1305 work?",
        "a": "The final two digits of 1305 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "What load can 1305-ETN9 take?",
        "a": "Catalogue values for 1305 ETN9: dynamic C 19 kN, static C0 5.4 kN, fatigue limit Pu 0.28 kN. Use C in life calculation and C0 for static checks at 25 mm bore."
      },
      {
        "q": "What is the speed rating of 1305-ETN9?",
        "a": "SKF lists a 22000 r/min thermal reference speed and a 15000 r/min mechanical limiting speed for 1305 ETN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1305",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1305-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 1305 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1305-ETN9",
      "1305 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1305-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1305 EKTN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19,
    "static_load_kN": 5.4,
    "fatigue_load_limit_kN": 0.28,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 260,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1305 carries code 05 = 25 mm (code × 5). Envelope 25×62×17 mm (0.984×2.441×0.669 in) with a 18.5 mm radial section height, C 19 kN, C0 5.4 kN and Pu 0.28 kN. The open 1305 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 22000 r/min, limiting speed 15000 r/min, catalogue mass 260 g.",
    "applications": [
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1305-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1305-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "On a sleeve-mounted 1305-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 1305-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 15000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.28 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 25 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1305-EKTN9?",
        "a": "SKF 1305 EKTN9 measures 25 mm bore × 62 mm OD × 17 mm width (0.984 × 2.441 × 0.669 in), mass about 260 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1305 work?",
        "a": "The final two digits of 1305 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "What is the speed rating of 1305-EKTN9?",
        "a": "SKF lists a 22000 r/min thermal reference speed and a 15000 r/min mechanical limiting speed for 1305 EKTN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1305-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1305-EKTN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1305",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1305-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 1305 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1305-EKTN9",
      "1305 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2305-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2305 E-2RS1TN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19,
    "static_load_kN": 5.4,
    "fatigue_load_limit_kN": 0.28,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2305 carries code 05 = 25 mm (code × 5). Envelope 25×62×24 mm (0.984×2.441×0.945 in) with a 18.5 mm radial section height, C 19 kN, C0 5.4 kN and Pu 0.28 kN. SKF spells the sealed execution 2305 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 25 mm shaft. Limiting speed 7500 r/min, catalogue mass 340 g.",
    "applications": [
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 25 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Mount 2305-E-2RS1TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Do not wash 2305-E-2RS1TN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "The E-2RS1TN9 suffix on 2305-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 2305-E-2RS1TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.28 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2305-E-2RS1TN9?",
        "a": "SKF 2305 E-2RS1TN9 measures 25 mm bore × 62 mm OD × 24 mm width (0.984 × 2.441 × 0.945 in), mass about 340 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2305 work?",
        "a": "The final two digits of 2305 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "Which fits should I use for 2305-E-2RS1TN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 62 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2305-E-2RS1TN9?",
        "a": "Catalogue mass is 340 g for 2305 E-2RS1TN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2305",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×62×24 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2305-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×24 mm envelope with catalogue ratings within 10 %; 2305 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2305-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×24 mm envelope, but catalogue C/C0 differ between executions (19/5.4 kN vs 27/7.1 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2305-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×24 mm envelope, but catalogue C/C0 differ between executions (19/5.4 kN vs 27/7.1 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2305-E-2RS1TN9",
      "2305 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2305-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2305 E-2RS1KTN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19,
    "static_load_kN": 5.4,
    "fatigue_load_limit_kN": 0.28,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2305 carries code 05 = 25 mm (code × 5). Envelope 25×62×24 mm (0.984×2.441×0.945 in) with a 18.5 mm radial section height, C 19 kN, C0 5.4 kN and Pu 0.28 kN. SKF spells the sealed execution 2305 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 7500 r/min, catalogue mass 340 g.",
    "applications": [
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors",
      "small electric motors"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 2305-E-2RS1KTN9 (C 19 kN, C0 5.4 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2305-E-2RS1KTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The 2RS1 contact seals on 2305-E-2RS1KTN9 add drag and cap speed at 7500 r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The E-2RS1KTN9 suffix on 2305-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 25 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2305-E-2RS1KTN9?",
        "a": "SKF 2305 E-2RS1KTN9 measures 25 mm bore × 62 mm OD × 24 mm width (0.984 × 2.441 × 0.945 in), mass about 340 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2305 work?",
        "a": "The final two digits of 2305 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "Can 2305-E-2RS1KTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2305-E-2RS1KTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 62 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2305",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×62×24 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2305-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×24 mm envelope with catalogue ratings within 10 %; 2305 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2305-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×24 mm envelope, but catalogue C/C0 differ between executions (19/5.4 kN vs 27/7.1 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2305-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×24 mm envelope, but catalogue C/C0 differ between executions (19/5.4 kN vs 27/7.1 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2305-E-2RS1KTN9",
      "2305 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2305-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2305 ETN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 27,
    "static_load_kN": 7.1,
    "fatigue_load_limit_kN": 0.37,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "weight_g": 340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2305 carries code 05 = 25 mm (code × 5). Envelope 25×62×24 mm (0.984×2.441×0.945 in) with a 18.5 mm radial section height, C 27 kN, C0 7.1 kN and Pu 0.37 kN. The open 2305 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 25 mm shaft. Reference (thermal) speed 22000 r/min, limiting speed 16000 r/min, catalogue mass 340 g.",
    "applications": [
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 2305-ETN9 (C 27 kN, C0 7.1 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The fatigue load limit is 0.37 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The ETN9 suffix on 2305-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 16000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 2305-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.37 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 25 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2305-ETN9?",
        "a": "SKF 2305 ETN9 measures 25 mm bore × 62 mm OD × 24 mm width (0.984 × 2.441 × 0.945 in), mass about 340 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2305 work?",
        "a": "The final two digits of 2305 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "How heavy is 2305-ETN9?",
        "a": "Catalogue mass is 340 g for 2305 ETN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2305-ETN9 take?",
        "a": "Catalogue values for 2305 ETN9: dynamic C 27 kN, static C0 7.1 kN, fatigue limit Pu 0.37 kN. Use C in life calculation and C0 for static checks at 25 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2305",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2305-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×24 mm envelope, but catalogue C/C0 differ between executions (27/7.1 kN vs 19/5.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2305-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×24 mm envelope, but catalogue C/C0 differ between executions (27/7.1 kN vs 19/5.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2305-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×24 mm envelope with catalogue ratings within 10 %; 2305 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2305-ETN9",
      "2305 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2305-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2305 EKTN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 27,
    "static_load_kN": 7.1,
    "fatigue_load_limit_kN": 0.37,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "weight_g": 340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2305 carries code 05 = 25 mm (code × 5). Envelope 25×62×24 mm (0.984×2.441×0.945 in) with a 18.5 mm radial section height, C 27 kN, C0 7.1 kN and Pu 0.37 kN. The open 2305 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 22000 r/min, limiting speed 16000 r/min, catalogue mass 340 g.",
    "applications": [
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts",
      "woodworking machine spindles"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2305-EKTN9 chamfer so the 24 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "At 25 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The K suffix means a 1:12 tapered bore: 2305-EKTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The EKTN9 suffix on 2305-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 16000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 25 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 2305-EKTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2305-EKTN9?",
        "a": "SKF 2305 EKTN9 measures 25 mm bore × 62 mm OD × 24 mm width (0.984 × 2.441 × 0.945 in), mass about 340 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2305 work?",
        "a": "The final two digits of 2305 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "How much misalignment can 2305-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2305-EKTN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2305-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2305",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2305-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×24 mm envelope, but catalogue C/C0 differ between executions (27/7.1 kN vs 19/5.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2305-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×24 mm envelope, but catalogue C/C0 differ between executions (27/7.1 kN vs 19/5.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2305-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×24 mm envelope with catalogue ratings within 10 %; 2305 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2305-EKTN9",
      "2305 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1206-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1206 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 15.6,
    "static_load_kN": 4.65,
    "fatigue_load_limit_kN": 0.24,
    "reference_speed_rpm": 24000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1206 carries code 06 = 30 mm (code × 5). Envelope 30×62×16 mm (1.181×2.441×0.63 in) with a 16.0 mm radial section height, C 15.6 kN, C0 4.65 kN and Pu 0.24 kN. The open 1206 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 30 mm shaft. Reference (thermal) speed 24000 r/min, limiting speed 15000 r/min, catalogue mass 220 g.",
    "applications": [
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts",
      "woodworking machine spindles"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 30 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "At 30 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The ETN9 suffix on 1206-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 15000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.24 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 30 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 1206-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1206-ETN9?",
        "a": "SKF 1206 ETN9 measures 30 mm bore × 62 mm OD × 16 mm width (1.181 × 2.441 × 0.63 in), mass about 220 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1206 work?",
        "a": "The final two digits of 1206 are bore code 06, multiplied by 5 to give 30 mm."
      },
      {
        "q": "What load can 1206-ETN9 take?",
        "a": "Catalogue values for 1206 ETN9: dynamic C 15.6 kN, static C0 4.65 kN, fatigue limit Pu 0.24 kN. Use C in life calculation and C0 for static checks at 30 mm bore."
      },
      {
        "q": "What is the speed rating of 1206-ETN9?",
        "a": "SKF lists a 24000 r/min thermal reference speed and a 15000 r/min mechanical limiting speed for 1206 ETN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1206",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1206-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 1206 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11206-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 11206 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1206-ETN9",
      "1206 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1206-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1206 EKTN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 15.6,
    "static_load_kN": 4.65,
    "fatigue_load_limit_kN": 0.24,
    "reference_speed_rpm": 24000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1206 carries code 06 = 30 mm (code × 5). Envelope 30×62×16 mm (1.181×2.441×0.63 in) with a 16.0 mm radial section height, C 15.6 kN, C0 4.65 kN and Pu 0.24 kN. The open 1206 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 24000 r/min, limiting speed 15000 r/min, catalogue mass 220 g.",
    "applications": [
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 1206-EKTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Catalogue ratings for 1206-EKTN9 (C 15.6 kN, C0 4.65 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The K suffix means a 1:12 tapered bore: 1206-EKTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The EKTN9 suffix on 1206-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 15000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 1206-EKTN9 (C 15.6 kN, C0 4.65 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1206-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1206-EKTN9?",
        "a": "SKF 1206 EKTN9 measures 30 mm bore × 62 mm OD × 16 mm width (1.181 × 2.441 × 0.63 in), mass about 220 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1206 work?",
        "a": "The final two digits of 1206 are bore code 06, multiplied by 5 to give 30 mm."
      },
      {
        "q": "How heavy is 1206-EKTN9?",
        "a": "Catalogue mass is 220 g for 1206 EKTN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 1206-EKTN9 take?",
        "a": "Catalogue values for 1206 EKTN9: dynamic C 15.6 kN, static C0 4.65 kN, fatigue limit Pu 0.24 kN. Use C in life calculation and C0 for static checks at 30 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1206",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1206-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 1206 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11206-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 11206 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1206-EKTN9",
      "1206 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2206-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2206 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 15.6,
    "static_load_kN": 4.65,
    "fatigue_load_limit_kN": 0.24,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 260,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2206 carries code 06 = 30 mm (code × 5). Envelope 30×62×20 mm (1.181×2.441×0.787 in) with a 16.0 mm radial section height, C 15.6 kN, C0 4.65 kN and Pu 0.24 kN. SKF spells the sealed execution 2206 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 30 mm shaft. Limiting speed 7500 r/min, catalogue mass 260 g.",
    "applications": [
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts",
      "woodworking machine spindles"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2206-E-2RS1TN9 chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "At 30 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2206-E-2RS1TN9 to avoid seal-lip binding.",
      "The E-2RS1TN9 suffix on 2206-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 30 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2206-E-2RS1TN9 (C 15.6 kN, C0 4.65 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2206-E-2RS1TN9?",
        "a": "SKF 2206 E-2RS1TN9 measures 30 mm bore × 62 mm OD × 20 mm width (1.181 × 2.441 × 0.787 in), mass about 260 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2206 work?",
        "a": "The final two digits of 2206 are bore code 06, multiplied by 5 to give 30 mm."
      },
      {
        "q": "How much misalignment can 2206-E-2RS1TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2206-E-2RS1TN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2206-E-2RS1TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2206",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2206-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×20 mm envelope with catalogue ratings within 10 %; 2206 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2206-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope, but catalogue C/C0 differ between executions (15.6/4.65 kN vs 23.8/6.7 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2206-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope, but catalogue C/C0 differ between executions (15.6/4.65 kN vs 23.8/6.7 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2206-E-2RS1TN9",
      "2206 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2206-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2206 E-2RS1KTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 15.6,
    "static_load_kN": 4.65,
    "fatigue_load_limit_kN": 0.24,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 260,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2206 carries code 06 = 30 mm (code × 5). Envelope 30×62×20 mm (1.181×2.441×0.787 in) with a 16.0 mm radial section height, C 15.6 kN, C0 4.65 kN and Pu 0.24 kN. SKF spells the sealed execution 2206 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 7500 r/min, catalogue mass 260 g.",
    "applications": [
      "food-processing conveyors",
      "small electric motors",
      "conveyor idler rollers",
      "agricultural machinery shafts"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2206-E-2RS1KTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Catalogue ratings for 2206-E-2RS1KTN9 (C 15.6 kN, C0 4.65 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The 2RS1 contact seals on 2206-E-2RS1KTN9 add drag and cap speed at 7500 r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The E-2RS1KTN9 suffix on 2206-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2206-E-2RS1KTN9 chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2206-E-2RS1KTN9?",
        "a": "SKF 2206 E-2RS1KTN9 measures 30 mm bore × 62 mm OD × 20 mm width (1.181 × 2.441 × 0.787 in), mass about 260 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2206 work?",
        "a": "The final two digits of 2206 are bore code 06, multiplied by 5 to give 30 mm."
      },
      {
        "q": "Can 2206-E-2RS1KTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2206-E-2RS1KTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 62 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2206",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2206-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×20 mm envelope with catalogue ratings within 10 %; 2206 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2206-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope, but catalogue C/C0 differ between executions (15.6/4.65 kN vs 23.8/6.7 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2206-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope, but catalogue C/C0 differ between executions (15.6/4.65 kN vs 23.8/6.7 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2206-E-2RS1KTN9",
      "2206 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2206-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2206 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 23.8,
    "static_load_kN": 6.7,
    "fatigue_load_limit_kN": 0.35,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 260,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2206 carries code 06 = 30 mm (code × 5). Envelope 30×62×20 mm (1.181×2.441×0.787 in) with a 16.0 mm radial section height, C 23.8 kN, C0 6.7 kN and Pu 0.35 kN. The open 2206 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 30 mm shaft. Reference (thermal) speed 22000 r/min, limiting speed 15000 r/min, catalogue mass 260 g.",
    "applications": [
      "textile spindles and looms",
      "fan and blower shafts",
      "woodworking machine spindles",
      "light gearbox layshafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2206-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The spherical outer raceway lets 2206-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The ETN9 suffix on 2206-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 15000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 30 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2206-ETN9 (C 23.8 kN, C0 6.7 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 2206-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2206-ETN9?",
        "a": "SKF 2206 ETN9 measures 30 mm bore × 62 mm OD × 20 mm width (1.181 × 2.441 × 0.787 in), mass about 260 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2206 work?",
        "a": "The final two digits of 2206 are bore code 06, multiplied by 5 to give 30 mm."
      },
      {
        "q": "What is the speed rating of 2206-ETN9?",
        "a": "SKF lists a 22000 r/min thermal reference speed and a 15000 r/min mechanical limiting speed for 2206 ETN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 2206-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2206-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2206",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2206-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope, but catalogue C/C0 differ between executions (23.8/6.7 kN vs 15.6/4.65 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2206-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope, but catalogue C/C0 differ between executions (23.8/6.7 kN vs 15.6/4.65 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2206-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×20 mm envelope with catalogue ratings within 10 %; 2206 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2206-ETN9",
      "2206 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2206-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2206 EKTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 23.8,
    "static_load_kN": 6.7,
    "fatigue_load_limit_kN": 0.35,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 260,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2206 carries code 06 = 30 mm (code × 5). Envelope 30×62×20 mm (1.181×2.441×0.787 in) with a 16.0 mm radial section height, C 23.8 kN, C0 6.7 kN and Pu 0.35 kN. The open 2206 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 22000 r/min, limiting speed 15000 r/min, catalogue mass 260 g.",
    "applications": [
      "fan and blower shafts",
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 30 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Fillet radii must clear the 2206-EKTN9 chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The EKTN9 suffix on 2206-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 15000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 2206-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.35 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2206-EKTN9?",
        "a": "SKF 2206 EKTN9 measures 30 mm bore × 62 mm OD × 20 mm width (1.181 × 2.441 × 0.787 in), mass about 260 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2206 work?",
        "a": "The final two digits of 2206 are bore code 06, multiplied by 5 to give 30 mm."
      },
      {
        "q": "What load can 2206-EKTN9 take?",
        "a": "Catalogue values for 2206 EKTN9: dynamic C 23.8 kN, static C0 6.7 kN, fatigue limit Pu 0.35 kN. Use C in life calculation and C0 for static checks at 30 mm bore."
      },
      {
        "q": "What is the speed rating of 2206-EKTN9?",
        "a": "SKF lists a 22000 r/min thermal reference speed and a 15000 r/min mechanical limiting speed for 2206 EKTN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2206",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2206-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope, but catalogue C/C0 differ between executions (23.8/6.7 kN vs 15.6/4.65 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2206-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×20 mm envelope, but catalogue C/C0 differ between executions (23.8/6.7 kN vs 15.6/4.65 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2206-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×20 mm envelope with catalogue ratings within 10 %; 2206 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2206-EKTN9",
      "2206 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1306-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1306 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.5,
    "static_load_kN": 6.8,
    "fatigue_load_limit_kN": 0.36,
    "reference_speed_rpm": 19000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 390,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1306 carries code 06 = 30 mm (code × 5). Envelope 30×72×19 mm (1.181×2.835×0.748 in) with a 21.0 mm radial section height, C 22.5 kN, C0 6.8 kN and Pu 0.36 kN. The open 1306 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 30 mm shaft. Reference (thermal) speed 19000 r/min, limiting speed 13000 r/min, catalogue mass 390 g.",
    "applications": [
      "textile spindles and looms",
      "fan and blower shafts",
      "woodworking machine spindles",
      "light gearbox layshafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.36 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The spherical outer raceway lets 1306-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The ETN9 suffix on 1306-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 13000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 30 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 1306-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 1306-ETN9 chamfer so the 19 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1306-ETN9?",
        "a": "SKF 1306 ETN9 measures 30 mm bore × 72 mm OD × 19 mm width (1.181 × 2.835 × 0.748 in), mass about 390 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1306 work?",
        "a": "The final two digits of 1306 are bore code 06, multiplied by 5 to give 30 mm."
      },
      {
        "q": "How heavy is 1306-ETN9?",
        "a": "Catalogue mass is 390 g for 1306 ETN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 1306-ETN9 take?",
        "a": "Catalogue values for 1306 ETN9: dynamic C 22.5 kN, static C0 6.8 kN, fatigue limit Pu 0.36 kN. Use C in life calculation and C0 for static checks at 30 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1306",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1306-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 1306 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1306-ETN9",
      "1306 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1306-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1306 EKTN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.5,
    "static_load_kN": 6.8,
    "fatigue_load_limit_kN": 0.36,
    "reference_speed_rpm": 19000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 390,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1306 carries code 06 = 30 mm (code × 5). Envelope 30×72×19 mm (1.181×2.835×0.748 in) with a 21.0 mm radial section height, C 22.5 kN, C0 6.8 kN and Pu 0.36 kN. The open 1306 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 19000 r/min, limiting speed 13000 r/min, catalogue mass 390 g.",
    "applications": [
      "fan and blower shafts",
      "woodworking machine spindles",
      "light gearbox layshafts",
      "food-processing conveyors"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 30 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the 1306-EKTN9 chamfer so the 19 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The K suffix means a 1:12 tapered bore: 1306-EKTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The EKTN9 suffix on 1306-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 13000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 1306-EKTN9 chamfer so the 19 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1306-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1306-EKTN9?",
        "a": "SKF 1306 EKTN9 measures 30 mm bore × 72 mm OD × 19 mm width (1.181 × 2.835 × 0.748 in), mass about 390 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1306 work?",
        "a": "The final two digits of 1306 are bore code 06, multiplied by 5 to give 30 mm."
      },
      {
        "q": "How much misalignment can 1306-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1306-EKTN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 1306-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1306",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1306-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 1306 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1306-EKTN9",
      "1306 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2306-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2306 E-2RS1TN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.5,
    "static_load_kN": 6.8,
    "fatigue_load_limit_kN": 0.36,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 510,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2306 carries code 06 = 30 mm (code × 5). Envelope 30×72×27 mm (1.181×2.835×1.063 in) with a 21.0 mm radial section height, C 22.5 kN, C0 6.8 kN and Pu 0.36 kN. SKF spells the sealed execution 2306 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 30 mm shaft. Limiting speed 6700 r/min, catalogue mass 510 g.",
    "applications": [
      "conveyor idler rollers",
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2306-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The fatigue load limit is 0.36 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2306-E-2RS1TN9 to avoid seal-lip binding.",
      "The E-2RS1TN9 suffix on 2306-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6700 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2306-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 30 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2306-E-2RS1TN9?",
        "a": "SKF 2306 E-2RS1TN9 measures 30 mm bore × 72 mm OD × 27 mm width (1.181 × 2.835 × 1.063 in), mass about 510 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2306 work?",
        "a": "The final two digits of 2306 are bore code 06, multiplied by 5 to give 30 mm."
      },
      {
        "q": "How heavy is 2306-E-2RS1TN9?",
        "a": "Catalogue mass is 510 g for 2306 E-2RS1TN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2306-E-2RS1TN9 take?",
        "a": "Catalogue values for 2306 E-2RS1TN9: dynamic C 22.5 kN, static C0 6.8 kN, fatigue limit Pu 0.36 kN. Use C in life calculation and C0 for static checks at 30 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2306",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×72×27 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2306-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×27 mm envelope with catalogue ratings within 10 %; 2306 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2306-K",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×27 mm envelope, but catalogue C/C0 differ between executions (22.5/6.8 kN vs 31.2/8.8 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2306-E-2RS1TN9",
      "2306 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2306-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2306 E-2RS1KTN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.5,
    "static_load_kN": 6.8,
    "fatigue_load_limit_kN": 0.36,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 510,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2306 carries code 06 = 30 mm (code × 5). Envelope 30×72×27 mm (1.181×2.835×1.063 in) with a 21.0 mm radial section height, C 22.5 kN, C0 6.8 kN and Pu 0.36 kN. SKF spells the sealed execution 2306 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 6700 r/min, catalogue mass 510 g.",
    "applications": [
      "agricultural machinery shafts",
      "textile spindles and looms",
      "fan and blower shafts",
      "woodworking machine spindles"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 30 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "At 30 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The 2RS1 contact seals on 2306-E-2RS1KTN9 add drag and cap speed at 6700 r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The E-2RS1KTN9 suffix on 2306-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6700 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 2306-E-2RS1KTN9 (C 22.5 kN, C0 6.8 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2306-E-2RS1KTN9?",
        "a": "SKF 2306 E-2RS1KTN9 measures 30 mm bore × 72 mm OD × 27 mm width (1.181 × 2.835 × 1.063 in), mass about 510 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2306 work?",
        "a": "The final two digits of 2306 are bore code 06, multiplied by 5 to give 30 mm."
      },
      {
        "q": "What load can 2306-E-2RS1KTN9 take?",
        "a": "Catalogue values for 2306 E-2RS1KTN9: dynamic C 22.5 kN, static C0 6.8 kN, fatigue limit Pu 0.36 kN. Use C in life calculation and C0 for static checks at 30 mm bore."
      },
      {
        "q": "What is the speed rating of 2306-E-2RS1KTN9?",
        "a": "SKF publishes only the 6700 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2306",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×72×27 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2306-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×27 mm envelope with catalogue ratings within 10 %; 2306 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2306-K",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×27 mm envelope, but catalogue C/C0 differ between executions (22.5/6.8 kN vs 31.2/8.8 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2306-E-2RS1KTN9",
      "2306 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2306-K",
    "brand": "SKF",
    "manufacturer_designation": "2306 K",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 31.2,
    "static_load_kN": 8.8,
    "fatigue_load_limit_kN": 0.45,
    "reference_speed_rpm": 18000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2306 carries code 06 = 30 mm (code × 5). Envelope 30×72×27 mm (1.181×2.835×1.063 in) with a 21.0 mm radial section height, C 31.2 kN, C0 8.8 kN and Pu 0.45 kN. The open 2306 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 18000 r/min, limiting speed 13000 r/min, catalogue mass 500 g.",
    "applications": [
      "textile spindles and looms",
      "fan and blower shafts",
      "woodworking machine spindles",
      "light gearbox layshafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2306-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The spherical outer raceway lets 2306-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "On a sleeve-mounted 2306-K, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The  suffix on 2306-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 13000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 2306-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2306-K chamfer so the 27 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2306-K?",
        "a": "SKF 2306 K measures 30 mm bore × 72 mm OD × 27 mm width (1.181 × 2.835 × 1.063 in), mass about 500 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2306 work?",
        "a": "The final two digits of 2306 are bore code 06, multiplied by 5 to give 30 mm."
      },
      {
        "q": "What is the speed rating of 2306-K?",
        "a": "SKF lists a 18000 r/min thermal reference speed and a 13000 r/min mechanical limiting speed for 2306 K; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 2306-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2306-K allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2306",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2306-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×27 mm envelope, but catalogue C/C0 differ between executions (31.2/8.8 kN vs 22.5/6.8 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2306-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×27 mm envelope, but catalogue C/C0 differ between executions (31.2/8.8 kN vs 22.5/6.8 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2306-K",
      "2306 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1207-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1207 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19,
    "static_load_kN": 6,
    "fatigue_load_limit_kN": 0.31,
    "reference_speed_rpm": 20000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 320,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1207 carries code 07 = 35 mm (code × 5). Envelope 35×72×17 mm (1.378×2.835×0.669 in) with a 18.5 mm radial section height, C 19 kN, C0 6 kN and Pu 0.31 kN. The open 1207 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 35 mm shaft. Reference (thermal) speed 20000 r/min, limiting speed 13000 r/min, catalogue mass 320 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.31 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The spherical outer raceway lets 1207-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The ETN9 suffix on 1207-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 13000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 35 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 1207-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 1207-ETN9 chamfer so the 17 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1207-ETN9?",
        "a": "SKF 1207 ETN9 measures 35 mm bore × 72 mm OD × 17 mm width (1.378 × 2.835 × 0.669 in), mass about 320 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1207 work?",
        "a": "The final two digits of 1207 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "How heavy is 1207-ETN9?",
        "a": "Catalogue mass is 320 g for 1207 ETN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 1207-ETN9 take?",
        "a": "Catalogue values for 1207 ETN9: dynamic C 19 kN, static C0 6 kN, fatigue limit Pu 0.31 kN. Use C in life calculation and C0 for static checks at 35 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1207",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1207-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 1207 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11207-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 11207 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1207-ETN9",
      "1207 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1207-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1207 EKTN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19,
    "static_load_kN": 6,
    "fatigue_load_limit_kN": 0.31,
    "reference_speed_rpm": 20000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 320,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1207 carries code 07 = 35 mm (code × 5). Envelope 35×72×17 mm (1.378×2.835×0.669 in) with a 18.5 mm radial section height, C 19 kN, C0 6 kN and Pu 0.31 kN. The open 1207 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 20000 r/min, limiting speed 13000 r/min, catalogue mass 320 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 35 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the 1207-EKTN9 chamfer so the 17 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "On a sleeve-mounted 1207-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 1207-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 13000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 1207-EKTN9 chamfer so the 17 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1207-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1207-EKTN9?",
        "a": "SKF 1207 EKTN9 measures 35 mm bore × 72 mm OD × 17 mm width (1.378 × 2.835 × 0.669 in), mass about 320 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1207 work?",
        "a": "The final two digits of 1207 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "Which fits should I use for 1207-EKTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 72 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 1207-EKTN9?",
        "a": "Catalogue mass is 320 g for 1207 EKTN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1207",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1207-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 1207 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11207-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 11207 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1207-EKTN9",
      "1207 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2207-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2207 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19,
    "static_load_kN": 6,
    "fatigue_load_limit_kN": 0.31,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 410,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2207 carries code 07 = 35 mm (code × 5). Envelope 35×72×23 mm (1.378×2.835×0.906 in) with a 18.5 mm radial section height, C 19 kN, C0 6 kN and Pu 0.31 kN. SKF spells the sealed execution 2207 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 35 mm shaft. Limiting speed 6300 r/min, catalogue mass 410 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2207-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The fatigue load limit is 0.31 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2207-E-2RS1TN9 to avoid seal-lip binding.",
      "The E-2RS1TN9 suffix on 2207-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2207-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 35 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2207-E-2RS1TN9?",
        "a": "SKF 2207 E-2RS1TN9 measures 35 mm bore × 72 mm OD × 23 mm width (1.378 × 2.835 × 0.906 in), mass about 410 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2207 work?",
        "a": "The final two digits of 2207 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "How heavy is 2207-E-2RS1TN9?",
        "a": "Catalogue mass is 410 g for 2207 E-2RS1TN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2207-E-2RS1TN9 take?",
        "a": "Catalogue values for 2207 E-2RS1TN9: dynamic C 19 kN, static C0 6 kN, fatigue limit Pu 0.31 kN. Use C in life calculation and C0 for static checks at 35 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2207",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2207-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×23 mm envelope with catalogue ratings within 10 %; 2207 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2207-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope, but catalogue C/C0 differ between executions (19/6 kN vs 30.2/8.8 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2207-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope, but catalogue C/C0 differ between executions (19/6 kN vs 30.2/8.8 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2207-E-2RS1TN9",
      "2207 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2207-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2207 E-2RS1KTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19,
    "static_load_kN": 6,
    "fatigue_load_limit_kN": 0.31,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 410,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2207 carries code 07 = 35 mm (code × 5). Envelope 35×72×23 mm (1.378×2.835×0.906 in) with a 18.5 mm radial section height, C 19 kN, C0 6 kN and Pu 0.31 kN. SKF spells the sealed execution 2207 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 6300 r/min, catalogue mass 410 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 35 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "At 35 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The 2RS1 contact seals on 2207-E-2RS1KTN9 add drag and cap speed at 6300 r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The E-2RS1KTN9 suffix on 2207-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 2207-E-2RS1KTN9 (C 19 kN, C0 6 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2207-E-2RS1KTN9?",
        "a": "SKF 2207 E-2RS1KTN9 measures 35 mm bore × 72 mm OD × 23 mm width (1.378 × 2.835 × 0.906 in), mass about 410 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2207 work?",
        "a": "The final two digits of 2207 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "What load can 2207-E-2RS1KTN9 take?",
        "a": "Catalogue values for 2207 E-2RS1KTN9: dynamic C 19 kN, static C0 6 kN, fatigue limit Pu 0.31 kN. Use C in life calculation and C0 for static checks at 35 mm bore."
      },
      {
        "q": "What is the speed rating of 2207-E-2RS1KTN9?",
        "a": "SKF publishes only the 6300 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2207",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2207-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×23 mm envelope with catalogue ratings within 10 %; 2207 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2207-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope, but catalogue C/C0 differ between executions (19/6 kN vs 30.2/8.8 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2207-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope, but catalogue C/C0 differ between executions (19/6 kN vs 30.2/8.8 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2207-E-2RS1KTN9",
      "2207 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2207-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2207 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 30.2,
    "static_load_kN": 8.8,
    "fatigue_load_limit_kN": 0.455,
    "reference_speed_rpm": 18000,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2207 carries code 07 = 35 mm (code × 5). Envelope 35×72×23 mm (1.378×2.835×0.906 in) with a 18.5 mm radial section height, C 30.2 kN, C0 8.8 kN and Pu 0.455 kN. The open 2207 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 35 mm shaft. Reference (thermal) speed 18000 r/min, limiting speed 12000 r/min, catalogue mass 400 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 35 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "At 35 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The ETN9 suffix on 2207-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 12000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2207-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 35 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2207-ETN9 (C 30.2 kN, C0 8.8 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2207-ETN9?",
        "a": "SKF 2207 ETN9 measures 35 mm bore × 72 mm OD × 23 mm width (1.378 × 2.835 × 0.906 in), mass about 400 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2207 work?",
        "a": "The final two digits of 2207 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "What load can 2207-ETN9 take?",
        "a": "Catalogue values for 2207 ETN9: dynamic C 30.2 kN, static C0 8.8 kN, fatigue limit Pu 0.455 kN. Use C in life calculation and C0 for static checks at 35 mm bore."
      },
      {
        "q": "What is the speed rating of 2207-ETN9?",
        "a": "SKF lists a 18000 r/min thermal reference speed and a 12000 r/min mechanical limiting speed for 2207 ETN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2207",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2207-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope, but catalogue C/C0 differ between executions (30.2/8.8 kN vs 19/6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2207-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope, but catalogue C/C0 differ between executions (30.2/8.8 kN vs 19/6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2207-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×23 mm envelope with catalogue ratings within 10 %; 2207 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2207-ETN9",
      "2207 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2207-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2207 EKTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 30.2,
    "static_load_kN": 8.8,
    "fatigue_load_limit_kN": 0.455,
    "reference_speed_rpm": 18000,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2207 carries code 07 = 35 mm (code × 5). Envelope 35×72×23 mm (1.378×2.835×0.906 in) with a 18.5 mm radial section height, C 30.2 kN, C0 8.8 kN and Pu 0.455 kN. The open 2207 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 18000 r/min, limiting speed 12000 r/min, catalogue mass 400 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 2207-EKTN9 (C 30.2 kN, C0 8.8 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Catalogue ratings for 2207-EKTN9 (C 30.2 kN, C0 8.8 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "On a sleeve-mounted 2207-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 2207-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 12000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 2207-EKTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2207-EKTN9 chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2207-EKTN9?",
        "a": "SKF 2207 EKTN9 measures 35 mm bore × 72 mm OD × 23 mm width (1.378 × 2.835 × 0.906 in), mass about 400 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2207 work?",
        "a": "The final two digits of 2207 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "What is the speed rating of 2207-EKTN9?",
        "a": "SKF lists a 18000 r/min thermal reference speed and a 12000 r/min mechanical limiting speed for 2207 EKTN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 2207-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2207-EKTN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2207",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2207-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope, but catalogue C/C0 differ between executions (30.2/8.8 kN vs 19/6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2207-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×23 mm envelope, but catalogue C/C0 differ between executions (30.2/8.8 kN vs 19/6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2207-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×23 mm envelope with catalogue ratings within 10 %; 2207 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2207-EKTN9",
      "2207 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1307-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1307 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 8.5,
    "fatigue_load_limit_kN": 0.43,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 510,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1307 carries code 07 = 35 mm (code × 5). Envelope 35×80×21 mm (1.378×3.15×0.827 in) with a 22.5 mm radial section height, C 26.5 kN, C0 8.5 kN and Pu 0.43 kN. The open 1307 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 35 mm shaft. Reference (thermal) speed 16000 r/min, limiting speed 11000 r/min, catalogue mass 510 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 35 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "At 35 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The ETN9 suffix on 1307-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 11000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.43 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 35 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 1307-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1307-ETN9?",
        "a": "SKF 1307 ETN9 measures 35 mm bore × 80 mm OD × 21 mm width (1.378 × 3.15 × 0.827 in), mass about 510 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1307 work?",
        "a": "The final two digits of 1307 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "What load can 1307-ETN9 take?",
        "a": "Catalogue values for 1307 ETN9: dynamic C 26.5 kN, static C0 8.5 kN, fatigue limit Pu 0.43 kN. Use C in life calculation and C0 for static checks at 35 mm bore."
      },
      {
        "q": "What is the speed rating of 1307-ETN9?",
        "a": "SKF lists a 16000 r/min thermal reference speed and a 11000 r/min mechanical limiting speed for 1307 ETN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1307",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1307-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 1307 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1307-ETN9",
      "1307 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1307-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1307 EKTN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 8.5,
    "fatigue_load_limit_kN": 0.43,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 510,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1307 carries code 07 = 35 mm (code × 5). Envelope 35×80×21 mm (1.378×3.15×0.827 in) with a 22.5 mm radial section height, C 26.5 kN, C0 8.5 kN and Pu 0.43 kN. The open 1307 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 16000 r/min, limiting speed 11000 r/min, catalogue mass 510 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 1307-EKTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Catalogue ratings for 1307-EKTN9 (C 26.5 kN, C0 8.5 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "On a sleeve-mounted 1307-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 1307-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 11000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 1307-EKTN9 (C 26.5 kN, C0 8.5 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1307-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1307-EKTN9?",
        "a": "SKF 1307 EKTN9 measures 35 mm bore × 80 mm OD × 21 mm width (1.378 × 3.15 × 0.827 in), mass about 510 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1307 work?",
        "a": "The final two digits of 1307 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "What is the speed rating of 1307-EKTN9?",
        "a": "SKF lists a 16000 r/min thermal reference speed and a 11000 r/min mechanical limiting speed for 1307 EKTN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1307-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1307-EKTN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1307",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1307-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 1307 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1307-EKTN9",
      "1307 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2307-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2307 E-2RS1TN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 8.5,
    "fatigue_load_limit_kN": 0.43,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2307 carries code 07 = 35 mm (code × 5). Envelope 35×80×31 mm (1.378×3.15×1.22 in) with a 22.5 mm radial section height, C 26.5 kN, C0 8.5 kN and Pu 0.43 kN. SKF spells the sealed execution 2307 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 35 mm shaft. Limiting speed 5600 r/min, catalogue mass 700 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2307-E-2RS1TN9 chamfer so the 31 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "At 35 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Do not wash 2307-E-2RS1TN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "The E-2RS1TN9 suffix on 2307-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5600 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 35 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2307-E-2RS1TN9 (C 26.5 kN, C0 8.5 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2307-E-2RS1TN9?",
        "a": "SKF 2307 E-2RS1TN9 measures 35 mm bore × 80 mm OD × 31 mm width (1.378 × 3.15 × 1.22 in), mass about 700 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2307 work?",
        "a": "The final two digits of 2307 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "Which fits should I use for 2307-E-2RS1TN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 80 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2307-E-2RS1TN9?",
        "a": "Catalogue mass is 700 g for 2307 E-2RS1TN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2307",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×80×31 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2307-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×31 mm envelope with catalogue ratings within 10 %; 2307 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2307-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×31 mm envelope, but catalogue C/C0 differ between executions (26.5/8.5 kN vs 39.7/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2307-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×31 mm envelope, but catalogue C/C0 differ between executions (26.5/8.5 kN vs 39.7/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2307-E-2RS1TN9",
      "2307 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2307-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2307 E-2RS1KTN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 8.5,
    "fatigue_load_limit_kN": 0.43,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2307 carries code 07 = 35 mm (code × 5). Envelope 35×80×31 mm (1.378×3.15×1.22 in) with a 22.5 mm radial section height, C 26.5 kN, C0 8.5 kN and Pu 0.43 kN. SKF spells the sealed execution 2307 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 5600 r/min, catalogue mass 700 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2307-E-2RS1KTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Catalogue ratings for 2307-E-2RS1KTN9 (C 26.5 kN, C0 8.5 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Do not wash 2307-E-2RS1KTN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "On a sleeve-mounted 2307-E-2RS1KTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The E-2RS1KTN9 suffix on 2307-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5600 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2307-E-2RS1KTN9 chamfer so the 31 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2307-E-2RS1KTN9?",
        "a": "SKF 2307 E-2RS1KTN9 measures 35 mm bore × 80 mm OD × 31 mm width (1.378 × 3.15 × 1.22 in), mass about 700 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2307 work?",
        "a": "The final two digits of 2307 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "What is the speed rating of 2307-E-2RS1KTN9?",
        "a": "SKF publishes only the 5600 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      },
      {
        "q": "How much misalignment can 2307-E-2RS1KTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2307-E-2RS1KTN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2307",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×80×31 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2307-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×31 mm envelope with catalogue ratings within 10 %; 2307 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2307-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×31 mm envelope, but catalogue C/C0 differ between executions (26.5/8.5 kN vs 39.7/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2307-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×31 mm envelope, but catalogue C/C0 differ between executions (26.5/8.5 kN vs 39.7/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2307-E-2RS1KTN9",
      "2307 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2307-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2307 ETN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 39.7,
    "static_load_kN": 11.2,
    "fatigue_load_limit_kN": 0.59,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 680,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2307 carries code 07 = 35 mm (code × 5). Envelope 35×80×31 mm (1.378×3.15×1.22 in) with a 22.5 mm radial section height, C 39.7 kN, C0 11.2 kN and Pu 0.59 kN. The open 2307 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 35 mm shaft. Reference (thermal) speed 16000 r/min, limiting speed 12000 r/min, catalogue mass 680 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2307-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The spherical outer raceway lets 2307-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The ETN9 suffix on 2307-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 12000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 35 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2307-ETN9 (C 39.7 kN, C0 11.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 2307-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2307-ETN9?",
        "a": "SKF 2307 ETN9 measures 35 mm bore × 80 mm OD × 31 mm width (1.378 × 3.15 × 1.22 in), mass about 680 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2307 work?",
        "a": "The final two digits of 2307 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "What is the speed rating of 2307-ETN9?",
        "a": "SKF lists a 16000 r/min thermal reference speed and a 12000 r/min mechanical limiting speed for 2307 ETN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 2307-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2307-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2307",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2307-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×31 mm envelope, but catalogue C/C0 differ between executions (39.7/11.2 kN vs 26.5/8.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2307-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×31 mm envelope, but catalogue C/C0 differ between executions (39.7/11.2 kN vs 26.5/8.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2307-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×31 mm envelope with catalogue ratings within 10 %; 2307 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2307-ETN9",
      "2307 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2307-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2307 EKTN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 39.7,
    "static_load_kN": 11.2,
    "fatigue_load_limit_kN": 0.59,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 680,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2307 carries code 07 = 35 mm (code × 5). Envelope 35×80×31 mm (1.378×3.15×1.22 in) with a 22.5 mm radial section height, C 39.7 kN, C0 11.2 kN and Pu 0.59 kN. The open 2307 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 16000 r/min, limiting speed 12000 r/min, catalogue mass 680 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 35 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Fillet radii must clear the 2307-EKTN9 chamfer so the 31 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The K suffix means a 1:12 tapered bore: 2307-EKTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The EKTN9 suffix on 2307-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 12000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 2307-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.59 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2307-EKTN9?",
        "a": "SKF 2307 EKTN9 measures 35 mm bore × 80 mm OD × 31 mm width (1.378 × 3.15 × 1.22 in), mass about 680 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2307 work?",
        "a": "The final two digits of 2307 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "How much misalignment can 2307-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2307-EKTN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2307-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2307",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2307-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×31 mm envelope, but catalogue C/C0 differ between executions (39.7/11.2 kN vs 26.5/8.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2307-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×31 mm envelope, but catalogue C/C0 differ between executions (39.7/11.2 kN vs 26.5/8.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2307-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×31 mm envelope with catalogue ratings within 10 %; 2307 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2307-EKTN9",
      "2307 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1208-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1208 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19.9,
    "static_load_kN": 6.95,
    "fatigue_load_limit_kN": 0.36,
    "reference_speed_rpm": 18000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1208 carries code 08 = 40 mm (code × 5). Envelope 40×80×18 mm (1.575×3.15×0.709 in) with a 20.0 mm radial section height, C 19.9 kN, C0 6.95 kN and Pu 0.36 kN. The open 1208 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 40 mm shaft. Reference (thermal) speed 18000 r/min, limiting speed 11000 r/min, catalogue mass 420 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 1208-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Fillet radii must clear the 1208-ETN9 chamfer so the 18 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The ETN9 suffix on 1208-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 11000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 1208-ETN9 (C 19.9 kN, C0 6.95 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1208-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.36 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1208-ETN9?",
        "a": "SKF 1208 ETN9 measures 40 mm bore × 80 mm OD × 18 mm width (1.575 × 3.15 × 0.709 in), mass about 420 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1208 work?",
        "a": "The final two digits of 1208 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "Which fits should I use for 1208-ETN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 80 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 1208-ETN9?",
        "a": "Catalogue mass is 420 g for 1208 ETN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1208",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1208-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 1208 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11208-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 11208 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1208-ETN9",
      "1208 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1208-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1208 EKTN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19.9,
    "static_load_kN": 6.95,
    "fatigue_load_limit_kN": 0.36,
    "reference_speed_rpm": 18000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1208 carries code 08 = 40 mm (code × 5). Envelope 40×80×18 mm (1.575×3.15×0.709 in) with a 20.0 mm radial section height, C 19.9 kN, C0 6.95 kN and Pu 0.36 kN. The open 1208 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 18000 r/min, limiting speed 11000 r/min, catalogue mass 420 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.36 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The fatigue load limit is 0.36 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The K suffix means a 1:12 tapered bore: 1208-EKTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The EKTN9 suffix on 1208-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 11000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1208-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 40 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1208-EKTN9?",
        "a": "SKF 1208 EKTN9 measures 40 mm bore × 80 mm OD × 18 mm width (1.575 × 3.15 × 0.709 in), mass about 420 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1208 work?",
        "a": "The final two digits of 1208 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "How heavy is 1208-EKTN9?",
        "a": "Catalogue mass is 420 g for 1208 EKTN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 1208-EKTN9 take?",
        "a": "Catalogue values for 1208 EKTN9: dynamic C 19.9 kN, static C0 6.95 kN, fatigue limit Pu 0.36 kN. Use C in life calculation and C0 for static checks at 40 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1208",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1208-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 1208 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11208-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 11208 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1208-EKTN9",
      "1208 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2208-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2208 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19.9,
    "static_load_kN": 6.95,
    "fatigue_load_limit_kN": 0.36,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2208 carries code 08 = 40 mm (code × 5). Envelope 40×80×23 mm (1.575×3.15×0.906 in) with a 20.0 mm radial section height, C 19.9 kN, C0 6.95 kN and Pu 0.36 kN. SKF spells the sealed execution 2208 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 40 mm shaft. Limiting speed 5600 r/min, catalogue mass 500 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 40 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Fillet radii must clear the 2208-E-2RS1TN9 chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2208-E-2RS1TN9 to avoid seal-lip binding.",
      "The E-2RS1TN9 suffix on 2208-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5600 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2208-E-2RS1TN9 chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2208-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2208-E-2RS1TN9?",
        "a": "SKF 2208 E-2RS1TN9 measures 40 mm bore × 80 mm OD × 23 mm width (1.575 × 3.15 × 0.906 in), mass about 500 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2208 work?",
        "a": "The final two digits of 2208 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "How much misalignment can 2208-E-2RS1TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2208-E-2RS1TN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2208-E-2RS1TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2208",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2208-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×23 mm envelope with catalogue ratings within 10 %; 2208 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2208-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope, but catalogue C/C0 differ between executions (19.9/6.95 kN vs 31.9/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2208-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope, but catalogue C/C0 differ between executions (19.9/6.95 kN vs 31.9/10 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2208-E-2RS1TN9",
      "2208 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2208-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2208 E-2RS1KTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19.9,
    "static_load_kN": 6.95,
    "fatigue_load_limit_kN": 0.36,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2208 carries code 08 = 40 mm (code × 5). Envelope 40×80×23 mm (1.575×3.15×0.906 in) with a 20.0 mm radial section height, C 19.9 kN, C0 6.95 kN and Pu 0.36 kN. SKF spells the sealed execution 2208 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 5600 r/min, catalogue mass 500 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2208-E-2RS1KTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The fatigue load limit is 0.36 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Do not wash 2208-E-2RS1KTN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "On a sleeve-mounted 2208-E-2RS1KTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The E-2RS1KTN9 suffix on 2208-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5600 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 40 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2208-E-2RS1KTN9?",
        "a": "SKF 2208 E-2RS1KTN9 measures 40 mm bore × 80 mm OD × 23 mm width (1.575 × 3.15 × 0.906 in), mass about 500 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2208 work?",
        "a": "The final two digits of 2208 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "What is the speed rating of 2208-E-2RS1KTN9?",
        "a": "SKF publishes only the 5600 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      },
      {
        "q": "How much misalignment can 2208-E-2RS1KTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2208-E-2RS1KTN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2208",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2208-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×23 mm envelope with catalogue ratings within 10 %; 2208 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2208-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope, but catalogue C/C0 differ between executions (19.9/6.95 kN vs 31.9/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2208-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope, but catalogue C/C0 differ between executions (19.9/6.95 kN vs 31.9/10 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2208-E-2RS1KTN9",
      "2208 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2208-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2208 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 31.9,
    "static_load_kN": 10,
    "fatigue_load_limit_kN": 0.51,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 510,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2208 carries code 08 = 40 mm (code × 5). Envelope 40×80×23 mm (1.575×3.15×0.906 in) with a 20.0 mm radial section height, C 31.9 kN, C0 10 kN and Pu 0.51 kN. The open 2208 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 40 mm shaft. Reference (thermal) speed 16000 r/min, limiting speed 11000 r/min, catalogue mass 510 g.",
    "applications": [
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2208-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2208-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The ETN9 suffix on 2208-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 11000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2208-ETN9 chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2208-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 40 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2208-ETN9?",
        "a": "SKF 2208 ETN9 measures 40 mm bore × 80 mm OD × 23 mm width (1.575 × 3.15 × 0.906 in), mass about 510 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2208 work?",
        "a": "The final two digits of 2208 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "How heavy is 2208-ETN9?",
        "a": "Catalogue mass is 510 g for 2208 ETN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2208-ETN9 take?",
        "a": "Catalogue values for 2208 ETN9: dynamic C 31.9 kN, static C0 10 kN, fatigue limit Pu 0.51 kN. Use C in life calculation and C0 for static checks at 40 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2208",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2208-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope, but catalogue C/C0 differ between executions (31.9/10 kN vs 19.9/6.95 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2208-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope, but catalogue C/C0 differ between executions (31.9/10 kN vs 19.9/6.95 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2208-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×23 mm envelope with catalogue ratings within 10 %; 2208 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2208-ETN9",
      "2208 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2208-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2208 EKTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 31.9,
    "static_load_kN": 10,
    "fatigue_load_limit_kN": 0.51,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 510,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2208 carries code 08 = 40 mm (code × 5). Envelope 40×80×23 mm (1.575×3.15×0.906 in) with a 20.0 mm radial section height, C 31.9 kN, C0 10 kN and Pu 0.51 kN. The open 2208 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 16000 r/min, limiting speed 11000 r/min, catalogue mass 510 g.",
    "applications": [
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 2208-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Assign interference to the rotating ring: on a 40 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The K suffix means a 1:12 tapered bore: 2208-EKTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The EKTN9 suffix on 2208-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 11000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 40 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2208-EKTN9 (C 31.9 kN, C0 10 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2208-EKTN9?",
        "a": "SKF 2208 EKTN9 measures 40 mm bore × 80 mm OD × 23 mm width (1.575 × 3.15 × 0.906 in), mass about 510 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2208 work?",
        "a": "The final two digits of 2208 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "How much misalignment can 2208-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2208-EKTN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2208-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2208",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2208-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope, but catalogue C/C0 differ between executions (31.9/10 kN vs 19.9/6.95 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2208-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×23 mm envelope, but catalogue C/C0 differ between executions (31.9/10 kN vs 19.9/6.95 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2208-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×23 mm envelope with catalogue ratings within 10 %; 2208 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2208-EKTN9",
      "2208 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1308-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1308 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 33.8,
    "static_load_kN": 11.2,
    "fatigue_load_limit_kN": 0.57,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 680,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1308 carries code 08 = 40 mm (code × 5). Envelope 40×90×23 mm (1.575×3.543×0.906 in) with a 25.0 mm radial section height, C 33.8 kN, C0 11.2 kN and Pu 0.57 kN. The open 1308 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 40 mm shaft. Reference (thermal) speed 14000 r/min, limiting speed 9500 r/min, catalogue mass 680 g.",
    "applications": [
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 1308-ETN9 (C 33.8 kN, C0 11.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1308-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The ETN9 suffix on 1308-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 1308-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.57 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 40 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1308-ETN9?",
        "a": "SKF 1308 ETN9 measures 40 mm bore × 90 mm OD × 23 mm width (1.575 × 3.543 × 0.906 in), mass about 680 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1308 work?",
        "a": "The final two digits of 1308 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "Can 1308-ETN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 1308-ETN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 90 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1308",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1308-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 1308 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1308-ETN9",
      "1308 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1308-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1308 EKTN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 33.8,
    "static_load_kN": 11.2,
    "fatigue_load_limit_kN": 0.57,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 680,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1308 carries code 08 = 40 mm (code × 5). Envelope 40×90×23 mm (1.575×3.543×0.906 in) with a 25.0 mm radial section height, C 33.8 kN, C0 11.2 kN and Pu 0.57 kN. The open 1308 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 14000 r/min, limiting speed 9500 r/min, catalogue mass 680 g.",
    "applications": [
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 1308-EKTN9 chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring: on a 40 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The K suffix means a 1:12 tapered bore: 1308-EKTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The EKTN9 suffix on 1308-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 40 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 1308-EKTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1308-EKTN9?",
        "a": "SKF 1308 EKTN9 measures 40 mm bore × 90 mm OD × 23 mm width (1.575 × 3.543 × 0.906 in), mass about 680 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1308 work?",
        "a": "The final two digits of 1308 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "How much misalignment can 1308-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1308-EKTN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 1308-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1308",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1308-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 1308 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1308-EKTN9",
      "1308 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2308-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2308 E-2RS1TN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 33.8,
    "static_load_kN": 11.2,
    "fatigue_load_limit_kN": 0.57,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 960,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2308 carries code 08 = 40 mm (code × 5). Envelope 40×90×33 mm (1.575×3.543×1.299 in) with a 25.0 mm radial section height, C 33.8 kN, C0 11.2 kN and Pu 0.57 kN. SKF spells the sealed execution 2308 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 40 mm shaft. Limiting speed 5000 r/min, catalogue mass 960 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2308-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The spherical outer raceway lets 2308-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Do not wash 2308-E-2RS1TN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "The E-2RS1TN9 suffix on 2308-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 2308-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2308-E-2RS1TN9 chamfer so the 33 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2308-E-2RS1TN9?",
        "a": "SKF 2308 E-2RS1TN9 measures 40 mm bore × 90 mm OD × 33 mm width (1.575 × 3.543 × 1.299 in), mass about 960 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2308 work?",
        "a": "The final two digits of 2308 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "What is the speed rating of 2308-E-2RS1TN9?",
        "a": "SKF publishes only the 5000 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      },
      {
        "q": "How much misalignment can 2308-E-2RS1TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2308-E-2RS1TN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2308",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2308-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×33 mm envelope with catalogue ratings within 10 %; 2308 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2308-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope, but catalogue C/C0 differ between executions (33.8/11.2 kN vs 54/16 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2308-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope, but catalogue C/C0 differ between executions (33.8/11.2 kN vs 54/16 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2308-E-2RS1TN9",
      "2308 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2308-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2308 E-2RS1KTN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 33.8,
    "static_load_kN": 11.2,
    "fatigue_load_limit_kN": 0.57,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 960,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2308 carries code 08 = 40 mm (code × 5). Envelope 40×90×33 mm (1.575×3.543×1.299 in) with a 25.0 mm radial section height, C 33.8 kN, C0 11.2 kN and Pu 0.57 kN. SKF spells the sealed execution 2308 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 5000 r/min, catalogue mass 960 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 2308-E-2RS1KTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Fillet radii must clear the 2308-E-2RS1KTN9 chamfer so the 33 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Do not wash 2308-E-2RS1KTN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "On a sleeve-mounted 2308-E-2RS1KTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The E-2RS1KTN9 suffix on 2308-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2308-E-2RS1KTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2308-E-2RS1KTN9?",
        "a": "SKF 2308 E-2RS1KTN9 measures 40 mm bore × 90 mm OD × 33 mm width (1.575 × 3.543 × 1.299 in), mass about 960 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2308 work?",
        "a": "The final two digits of 2308 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "Which fits should I use for 2308-E-2RS1KTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 90 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2308-E-2RS1KTN9?",
        "a": "Catalogue mass is 960 g for 2308 E-2RS1KTN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2308",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2308-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×33 mm envelope with catalogue ratings within 10 %; 2308 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2308-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope, but catalogue C/C0 differ between executions (33.8/11.2 kN vs 54/16 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2308-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope, but catalogue C/C0 differ between executions (33.8/11.2 kN vs 54/16 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2308-E-2RS1KTN9",
      "2308 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2308-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2308 ETN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 54,
    "static_load_kN": 16,
    "fatigue_load_limit_kN": 0.82,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 930,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2308 carries code 08 = 40 mm (code × 5). Envelope 40×90×33 mm (1.575×3.543×1.299 in) with a 25.0 mm radial section height, C 54 kN, C0 16 kN and Pu 0.82 kN. The open 2308 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 40 mm shaft. Reference (thermal) speed 14000 r/min, limiting speed 10000 r/min, catalogue mass 930 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2308-ETN9 chamfer so the 33 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Fillet radii must clear the 2308-ETN9 chamfer so the 33 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The ETN9 suffix on 2308-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 10000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 2308-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2308-ETN9 chamfer so the 33 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2308-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2308-ETN9?",
        "a": "SKF 2308 ETN9 measures 40 mm bore × 90 mm OD × 33 mm width (1.575 × 3.543 × 1.299 in), mass about 930 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2308 work?",
        "a": "The final two digits of 2308 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "What load can 2308-ETN9 take?",
        "a": "Catalogue values for 2308 ETN9: dynamic C 54 kN, static C0 16 kN, fatigue limit Pu 0.82 kN. Use C in life calculation and C0 for static checks at 40 mm bore."
      },
      {
        "q": "What is the speed rating of 2308-ETN9?",
        "a": "SKF lists a 14000 r/min thermal reference speed and a 10000 r/min mechanical limiting speed for 2308 ETN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2308",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2308-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope, but catalogue C/C0 differ between executions (54/16 kN vs 33.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2308-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope, but catalogue C/C0 differ between executions (54/16 kN vs 33.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2308-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×33 mm envelope with catalogue ratings within 10 %; 2308 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2308-ETN9",
      "2308 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2308-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2308 EKTN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 54,
    "static_load_kN": 16,
    "fatigue_load_limit_kN": 0.82,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 930,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2308 carries code 08 = 40 mm (code × 5). Envelope 40×90×33 mm (1.575×3.543×1.299 in) with a 25.0 mm radial section height, C 54 kN, C0 16 kN and Pu 0.82 kN. The open 2308 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 14000 r/min, limiting speed 10000 r/min, catalogue mass 930 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2308-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The fatigue load limit is 0.82 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The K suffix means a 1:12 tapered bore: 2308-EKTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The EKTN9 suffix on 2308-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 10000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.82 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 40 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2308-EKTN9?",
        "a": "SKF 2308 EKTN9 measures 40 mm bore × 90 mm OD × 33 mm width (1.575 × 3.543 × 1.299 in), mass about 930 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2308 work?",
        "a": "The final two digits of 2308 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "How heavy is 2308-EKTN9?",
        "a": "Catalogue mass is 930 g for 2308 EKTN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2308-EKTN9 take?",
        "a": "Catalogue values for 2308 EKTN9: dynamic C 54 kN, static C0 16 kN, fatigue limit Pu 0.82 kN. Use C in life calculation and C0 for static checks at 40 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2308",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2308-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope, but catalogue C/C0 differ between executions (54/16 kN vs 33.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2308-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×33 mm envelope, but catalogue C/C0 differ between executions (54/16 kN vs 33.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2308-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×33 mm envelope with catalogue ratings within 10 %; 2308 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2308-EKTN9",
      "2308 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1209-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1209 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.9,
    "static_load_kN": 7.8,
    "fatigue_load_limit_kN": 0.4,
    "reference_speed_rpm": 17000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 470,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1209 carries code 09 = 45 mm (code × 5). Envelope 45×85×19 mm (1.772×3.346×0.748 in) with a 20.0 mm radial section height, C 22.9 kN, C0 7.8 kN and Pu 0.4 kN. The open 1209 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 45 mm shaft. Reference (thermal) speed 17000 r/min, limiting speed 11000 r/min, catalogue mass 470 g.",
    "applications": [
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 1209-ETN9 (C 22.9 kN, C0 7.8 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1209-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The ETN9 suffix on 1209-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 11000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 1209-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.4 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 45 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1209-ETN9?",
        "a": "SKF 1209 ETN9 measures 45 mm bore × 85 mm OD × 19 mm width (1.772 × 3.346 × 0.748 in), mass about 470 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1209 work?",
        "a": "The final two digits of 1209 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "What is the speed rating of 1209-ETN9?",
        "a": "SKF lists a 17000 r/min thermal reference speed and a 11000 r/min mechanical limiting speed for 1209 ETN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1209-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1209-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1209",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1209-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 1209 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11209-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 11209 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1209-ETN9",
      "1209 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1209-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1209 EKTN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.9,
    "static_load_kN": 7.8,
    "fatigue_load_limit_kN": 0.4,
    "reference_speed_rpm": 17000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 470,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1209 carries code 09 = 45 mm (code × 5). Envelope 45×85×19 mm (1.772×3.346×0.748 in) with a 20.0 mm radial section height, C 22.9 kN, C0 7.8 kN and Pu 0.4 kN. The open 1209 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 17000 r/min, limiting speed 11000 r/min, catalogue mass 470 g.",
    "applications": [
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 1209-EKTN9 chamfer so the 19 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring: on a 45 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The K suffix means a 1:12 tapered bore: 1209-EKTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The EKTN9 suffix on 1209-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 11000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 45 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 1209-EKTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1209-EKTN9?",
        "a": "SKF 1209 EKTN9 measures 45 mm bore × 85 mm OD × 19 mm width (1.772 × 3.346 × 0.748 in), mass about 470 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1209 work?",
        "a": "The final two digits of 1209 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "How much misalignment can 1209-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1209-EKTN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 1209-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1209",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1209-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 1209 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11209-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 11209 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1209-EKTN9",
      "1209 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2209-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2209 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.9,
    "static_load_kN": 7.8,
    "fatigue_load_limit_kN": 0.4,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 530,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2209 carries code 09 = 45 mm (code × 5). Envelope 45×85×23 mm (1.772×3.346×0.906 in) with a 20.0 mm radial section height, C 22.9 kN, C0 7.8 kN and Pu 0.4 kN. SKF spells the sealed execution 2209 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 45 mm shaft. Limiting speed 5300 r/min, catalogue mass 530 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2209-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The spherical outer raceway lets 2209-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The 2RS1 contact seals on 2209-E-2RS1TN9 add drag and cap speed at 5300 r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "The E-2RS1TN9 suffix on 2209-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 2209-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2209-E-2RS1TN9 chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2209-E-2RS1TN9?",
        "a": "SKF 2209 E-2RS1TN9 measures 45 mm bore × 85 mm OD × 23 mm width (1.772 × 3.346 × 0.906 in), mass about 530 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2209 work?",
        "a": "The final two digits of 2209 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "Can 2209-E-2RS1TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2209-E-2RS1TN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 85 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2209",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2209-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×23 mm envelope with catalogue ratings within 10 %; 2209 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2209-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope, but catalogue C/C0 differ between executions (22.9/7.8 kN vs 32.5/10.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2209-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope, but catalogue C/C0 differ between executions (22.9/7.8 kN vs 32.5/10.6 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2209-E-2RS1TN9",
      "2209 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2209-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2209 E-2RS1KTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.9,
    "static_load_kN": 7.8,
    "fatigue_load_limit_kN": 0.4,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 530,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2209 carries code 09 = 45 mm (code × 5). Envelope 45×85×23 mm (1.772×3.346×0.906 in) with a 20.0 mm radial section height, C 22.9 kN, C0 7.8 kN and Pu 0.4 kN. SKF spells the sealed execution 2209 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 5300 r/min, catalogue mass 530 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 2209-E-2RS1KTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Fillet radii must clear the 2209-E-2RS1KTN9 chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Do not wash 2209-E-2RS1KTN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "On a sleeve-mounted 2209-E-2RS1KTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The E-2RS1KTN9 suffix on 2209-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2209-E-2RS1KTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2209-E-2RS1KTN9?",
        "a": "SKF 2209 E-2RS1KTN9 measures 45 mm bore × 85 mm OD × 23 mm width (1.772 × 3.346 × 0.906 in), mass about 530 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2209 work?",
        "a": "The final two digits of 2209 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "Which fits should I use for 2209-E-2RS1KTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 85 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2209-E-2RS1KTN9?",
        "a": "Catalogue mass is 530 g for 2209 E-2RS1KTN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2209",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2209-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×23 mm envelope with catalogue ratings within 10 %; 2209 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2209-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope, but catalogue C/C0 differ between executions (22.9/7.8 kN vs 32.5/10.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2209-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope, but catalogue C/C0 differ between executions (22.9/7.8 kN vs 32.5/10.6 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2209-E-2RS1KTN9",
      "2209 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2209-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2209 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 32.5,
    "static_load_kN": 10.6,
    "fatigue_load_limit_kN": 0.54,
    "reference_speed_rpm": 15000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2209 carries code 09 = 45 mm (code × 5). Envelope 45×85×23 mm (1.772×3.346×0.906 in) with a 20.0 mm radial section height, C 32.5 kN, C0 10.6 kN and Pu 0.54 kN. The open 2209 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 45 mm shaft. Reference (thermal) speed 15000 r/min, limiting speed 10000 r/min, catalogue mass 550 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2209-ETN9 chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Fillet radii must clear the 2209-ETN9 chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The ETN9 suffix on 2209-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 10000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 2209-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2209-ETN9 chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2209-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2209-ETN9?",
        "a": "SKF 2209 ETN9 measures 45 mm bore × 85 mm OD × 23 mm width (1.772 × 3.346 × 0.906 in), mass about 550 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2209 work?",
        "a": "The final two digits of 2209 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "Which fits should I use for 2209-ETN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 85 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2209-ETN9?",
        "a": "Catalogue mass is 550 g for 2209 ETN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2209",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2209-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope, but catalogue C/C0 differ between executions (32.5/10.6 kN vs 22.9/7.8 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2209-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope, but catalogue C/C0 differ between executions (32.5/10.6 kN vs 22.9/7.8 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2209-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×23 mm envelope with catalogue ratings within 10 %; 2209 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2209-ETN9",
      "2209 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2209-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2209 EKTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 32.5,
    "static_load_kN": 10.6,
    "fatigue_load_limit_kN": 0.54,
    "reference_speed_rpm": 15000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2209 carries code 09 = 45 mm (code × 5). Envelope 45×85×23 mm (1.772×3.346×0.906 in) with a 20.0 mm radial section height, C 32.5 kN, C0 10.6 kN and Pu 0.54 kN. The open 2209 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 15000 r/min, limiting speed 10000 r/min, catalogue mass 550 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2209-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The fatigue load limit is 0.54 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The EKTN9 suffix on 2209-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 10000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.54 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 45 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2209-EKTN9?",
        "a": "SKF 2209 EKTN9 measures 45 mm bore × 85 mm OD × 23 mm width (1.772 × 3.346 × 0.906 in), mass about 550 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2209 work?",
        "a": "The final two digits of 2209 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "Can 2209-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2209-EKTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 85 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2209",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2209-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope, but catalogue C/C0 differ between executions (32.5/10.6 kN vs 22.9/7.8 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2209-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×23 mm envelope, but catalogue C/C0 differ between executions (32.5/10.6 kN vs 22.9/7.8 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2209-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×23 mm envelope with catalogue ratings within 10 %; 2209 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2209-EKTN9",
      "2209 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1309-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1309 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 39,
    "static_load_kN": 13.4,
    "fatigue_load_limit_kN": 0.7,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 960,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1309 carries code 09 = 45 mm (code × 5). Envelope 45×100×25 mm (1.772×3.937×0.984 in) with a 27.5 mm radial section height, C 39 kN, C0 13.4 kN and Pu 0.7 kN. The open 1309 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 45 mm shaft. Reference (thermal) speed 12000 r/min, limiting speed 8500 r/min, catalogue mass 960 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 1309-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Fillet radii must clear the 1309-ETN9 chamfer so the 25 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The ETN9 suffix on 1309-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 1309-ETN9 (C 39 kN, C0 13.4 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1309-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.7 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1309-ETN9?",
        "a": "SKF 1309 ETN9 measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 960 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1309 work?",
        "a": "The final two digits of 1309 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "How much misalignment can 1309-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1309-ETN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 1309-ETN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1309",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1309-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 1309 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1309-ETN9",
      "1309 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1309-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1309 EKTN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 39,
    "static_load_kN": 13.4,
    "fatigue_load_limit_kN": 0.7,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 960,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1309 carries code 09 = 45 mm (code × 5). Envelope 45×100×25 mm (1.772×3.937×0.984 in) with a 27.5 mm radial section height, C 39 kN, C0 13.4 kN and Pu 0.7 kN. The open 1309 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 12000 r/min, limiting speed 8500 r/min, catalogue mass 960 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.7 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The fatigue load limit is 0.7 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The K suffix means a 1:12 tapered bore: 1309-EKTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The EKTN9 suffix on 1309-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1309-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 45 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1309-EKTN9?",
        "a": "SKF 1309 EKTN9 measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 960 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1309 work?",
        "a": "The final two digits of 1309 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "How heavy is 1309-EKTN9?",
        "a": "Catalogue mass is 960 g for 1309 EKTN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 1309-EKTN9 take?",
        "a": "Catalogue values for 1309 EKTN9: dynamic C 39 kN, static C0 13.4 kN, fatigue limit Pu 0.7 kN. Use C in life calculation and C0 for static checks at 45 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1309",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1309-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 1309 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1309-EKTN9",
      "1309 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2309-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2309 E-2RS1TN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 39,
    "static_load_kN": 13.4,
    "fatigue_load_limit_kN": 0.7,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 1300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2309 carries code 09 = 45 mm (code × 5). Envelope 45×100×36 mm (1.772×3.937×1.417 in) with a 27.5 mm radial section height, C 39 kN, C0 13.4 kN and Pu 0.7 kN. SKF spells the sealed execution 2309 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 45 mm shaft. Limiting speed 4500 r/min, catalogue mass 1300 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 45 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Fillet radii must clear the 2309-E-2RS1TN9 chamfer so the 36 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Do not wash 2309-E-2RS1TN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "The E-2RS1TN9 suffix on 2309-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2309-E-2RS1TN9 chamfer so the 36 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2309-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2309-E-2RS1TN9?",
        "a": "SKF 2309 E-2RS1TN9 measures 45 mm bore × 100 mm OD × 36 mm width (1.772 × 3.937 × 1.417 in), mass about 1300 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2309 work?",
        "a": "The final two digits of 2309 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "Which fits should I use for 2309-E-2RS1TN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 100 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2309-E-2RS1TN9?",
        "a": "Catalogue mass is 1300 g for 2309 E-2RS1TN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2309",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2309-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×36 mm envelope with catalogue ratings within 10 %; 2309 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2309-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope, but catalogue C/C0 differ between executions (39/13.4 kN vs 63.7/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2309-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope, but catalogue C/C0 differ between executions (39/13.4 kN vs 63.7/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2309-E-2RS1TN9",
      "2309 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2309-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2309 E-2RS1KTN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 39,
    "static_load_kN": 13.4,
    "fatigue_load_limit_kN": 0.7,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 1300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2309 carries code 09 = 45 mm (code × 5). Envelope 45×100×36 mm (1.772×3.937×1.417 in) with a 27.5 mm radial section height, C 39 kN, C0 13.4 kN and Pu 0.7 kN. SKF spells the sealed execution 2309 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 4500 r/min, catalogue mass 1300 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2309-E-2RS1KTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The fatigue load limit is 0.7 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The 2RS1 contact seals on 2309-E-2RS1KTN9 add drag and cap speed at 4500 r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The E-2RS1KTN9 suffix on 2309-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 45 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2309-E-2RS1KTN9?",
        "a": "SKF 2309 E-2RS1KTN9 measures 45 mm bore × 100 mm OD × 36 mm width (1.772 × 3.937 × 1.417 in), mass about 1300 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2309 work?",
        "a": "The final two digits of 2309 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "Can 2309-E-2RS1KTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2309-E-2RS1KTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 100 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2309",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2309-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×36 mm envelope with catalogue ratings within 10 %; 2309 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2309-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope, but catalogue C/C0 differ between executions (39/13.4 kN vs 63.7/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2309-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope, but catalogue C/C0 differ between executions (39/13.4 kN vs 63.7/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2309-E-2RS1KTN9",
      "2309 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2309-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2309 ETN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 63.7,
    "static_load_kN": 19.3,
    "fatigue_load_limit_kN": 1,
    "reference_speed_rpm": 13000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 1250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2309 carries code 09 = 45 mm (code × 5). Envelope 45×100×36 mm (1.772×3.937×1.417 in) with a 27.5 mm radial section height, C 63.7 kN, C0 19.3 kN and Pu 1 kN. The open 2309 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 45 mm shaft. Reference (thermal) speed 13000 r/min, limiting speed 9000 r/min, catalogue mass 1250 g.",
    "applications": [
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2309-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2309-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The ETN9 suffix on 2309-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2309-ETN9 chamfer so the 36 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2309-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 45 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2309-ETN9?",
        "a": "SKF 2309 ETN9 measures 45 mm bore × 100 mm OD × 36 mm width (1.772 × 3.937 × 1.417 in), mass about 1250 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2309 work?",
        "a": "The final two digits of 2309 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "What is the speed rating of 2309-ETN9?",
        "a": "SKF lists a 13000 r/min thermal reference speed and a 9000 r/min mechanical limiting speed for 2309 ETN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 2309-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2309-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2309",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2309-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope, but catalogue C/C0 differ between executions (63.7/19.3 kN vs 39/13.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2309-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope, but catalogue C/C0 differ between executions (63.7/19.3 kN vs 39/13.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2309-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×36 mm envelope with catalogue ratings within 10 %; 2309 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2309-ETN9",
      "2309 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2309-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2309 EKTN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 63.7,
    "static_load_kN": 19.3,
    "fatigue_load_limit_kN": 1,
    "reference_speed_rpm": 13000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 1250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2309 carries code 09 = 45 mm (code × 5). Envelope 45×100×36 mm (1.772×3.937×1.417 in) with a 27.5 mm radial section height, C 63.7 kN, C0 19.3 kN and Pu 1 kN. The open 2309 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 13000 r/min, limiting speed 9000 r/min, catalogue mass 1250 g.",
    "applications": [
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 2309-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Assign interference to the rotating ring: on a 45 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The K suffix means a 1:12 tapered bore: 2309-EKTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The EKTN9 suffix on 2309-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 45 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2309-EKTN9 (C 63.7 kN, C0 19.3 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2309-EKTN9?",
        "a": "SKF 2309 EKTN9 measures 45 mm bore × 100 mm OD × 36 mm width (1.772 × 3.937 × 1.417 in), mass about 1250 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2309 work?",
        "a": "The final two digits of 2309 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "How much misalignment can 2309-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2309-EKTN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2309-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2309",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2309-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope, but catalogue C/C0 differ between executions (63.7/19.3 kN vs 39/13.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2309-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×36 mm envelope, but catalogue C/C0 differ between executions (63.7/19.3 kN vs 39/13.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2309-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×36 mm envelope with catalogue ratings within 10 %; 2309 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2309-EKTN9",
      "2309 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1210-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1210 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 9.15,
    "fatigue_load_limit_kN": 0.48,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 530,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1210 carries code 10 = 50 mm (code × 5). Envelope 50×90×20 mm (1.969×3.543×0.787 in) with a 20.0 mm radial section height, C 26.5 kN, C0 9.15 kN and Pu 0.48 kN. The open 1210 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 50 mm shaft. Reference (thermal) speed 16000 r/min, limiting speed 10000 r/min, catalogue mass 530 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1210-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Catalogue ratings for 1210-ETN9 (C 26.5 kN, C0 9.15 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The ETN9 suffix on 1210-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 10000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 1210-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 1210-ETN9 chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1210-ETN9?",
        "a": "SKF 1210 ETN9 measures 50 mm bore × 90 mm OD × 20 mm width (1.969 × 3.543 × 0.787 in), mass about 530 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1210 work?",
        "a": "The final two digits of 1210 are bore code 10, multiplied by 5 to give 50 mm."
      },
      {
        "q": "Can 1210-ETN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 1210-ETN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 90 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1210",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1210-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 1210 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11210-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 11210 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1210-ETN9",
      "1210 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1210-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1210 EKTN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 9.15,
    "fatigue_load_limit_kN": 0.48,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 530,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1210 carries code 10 = 50 mm (code × 5). Envelope 50×90×20 mm (1.969×3.543×0.787 in) with a 20.0 mm radial section height, C 26.5 kN, C0 9.15 kN and Pu 0.48 kN. The open 1210 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 16000 r/min, limiting speed 10000 r/min, catalogue mass 530 g.",
    "applications": [
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Mount 1210-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The EKTN9 suffix on 1210-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 10000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 1210-EKTN9 chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1210-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1210-EKTN9?",
        "a": "SKF 1210 EKTN9 measures 50 mm bore × 90 mm OD × 20 mm width (1.969 × 3.543 × 0.787 in), mass about 530 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1210 work?",
        "a": "The final two digits of 1210 are bore code 10, multiplied by 5 to give 50 mm."
      },
      {
        "q": "What load can 1210-EKTN9 take?",
        "a": "Catalogue values for 1210 EKTN9: dynamic C 26.5 kN, static C0 9.15 kN, fatigue limit Pu 0.48 kN. Use C in life calculation and C0 for static checks at 50 mm bore."
      },
      {
        "q": "What is the speed rating of 1210-EKTN9?",
        "a": "SKF lists a 16000 r/min thermal reference speed and a 10000 r/min mechanical limiting speed for 1210 EKTN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1210",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1210-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 1210 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11210-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 11210 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1210-EKTN9",
      "1210 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2210-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2210 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.9,
    "static_load_kN": 8.15,
    "fatigue_load_limit_kN": 0.42,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2210 carries code 10 = 50 mm (code × 5). Envelope 50×90×23 mm (1.969×3.543×0.906 in) with a 20.0 mm radial section height, C 22.9 kN, C0 8.15 kN and Pu 0.42 kN. SKF spells the sealed execution 2210 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 50 mm shaft. Limiting speed 4800 r/min, catalogue mass 570 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2210-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The fatigue load limit is 0.42 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The 2RS1 contact seals on 2210-E-2RS1TN9 add drag and cap speed at 4800 r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "The E-2RS1TN9 suffix on 2210-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4800 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.42 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2210-E-2RS1TN9?",
        "a": "SKF 2210 E-2RS1TN9 measures 50 mm bore × 90 mm OD × 23 mm width (1.969 × 3.543 × 0.906 in), mass about 570 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2210 work?",
        "a": "The final two digits of 2210 are bore code 10, multiplied by 5 to give 50 mm."
      },
      {
        "q": "Can 2210-E-2RS1TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2210-E-2RS1TN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 90 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2210",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2210-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×23 mm envelope with catalogue ratings within 10 %; 2210 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2210-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope, but catalogue C/C0 differ between executions (22.9/8.15 kN vs 33.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2210-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope, but catalogue C/C0 differ between executions (22.9/8.15 kN vs 33.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2210-E-2RS1TN9",
      "2210 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2210-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2210 E-2RS1KTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.9,
    "static_load_kN": 8.15,
    "fatigue_load_limit_kN": 0.42,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2210 carries code 10 = 50 mm (code × 5). Envelope 50×90×23 mm (1.969×3.543×0.906 in) with a 20.0 mm radial section height, C 22.9 kN, C0 8.15 kN and Pu 0.42 kN. SKF spells the sealed execution 2210 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 4800 r/min, catalogue mass 570 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2210-E-2RS1KTN9 to avoid seal-lip binding.",
      "The K suffix means a 1:12 tapered bore: 2210-E-2RS1KTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The E-2RS1KTN9 suffix on 2210-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4800 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 2210-E-2RS1KTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2210-E-2RS1KTN9?",
        "a": "SKF 2210 E-2RS1KTN9 measures 50 mm bore × 90 mm OD × 23 mm width (1.969 × 3.543 × 0.906 in), mass about 570 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2210 work?",
        "a": "The final two digits of 2210 are bore code 10, multiplied by 5 to give 50 mm."
      },
      {
        "q": "How much misalignment can 2210-E-2RS1KTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2210-E-2RS1KTN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2210-E-2RS1KTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2210",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2210-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×23 mm envelope with catalogue ratings within 10 %; 2210 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2210-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope, but catalogue C/C0 differ between executions (22.9/8.15 kN vs 33.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2210-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope, but catalogue C/C0 differ between executions (22.9/8.15 kN vs 33.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2210-E-2RS1KTN9",
      "2210 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2210-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2210 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 33.8,
    "static_load_kN": 11.2,
    "fatigue_load_limit_kN": 0.57,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2210 carries code 10 = 50 mm (code × 5). Envelope 50×90×23 mm (1.969×3.543×0.906 in) with a 20.0 mm radial section height, C 33.8 kN, C0 11.2 kN and Pu 0.57 kN. The open 2210 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 50 mm shaft. Reference (thermal) speed 14000 r/min, limiting speed 9500 r/min, catalogue mass 600 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 50 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The ETN9 suffix on 2210-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.57 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 2210-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2210-ETN9?",
        "a": "SKF 2210 ETN9 measures 50 mm bore × 90 mm OD × 23 mm width (1.969 × 3.543 × 0.906 in), mass about 600 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2210 work?",
        "a": "The final two digits of 2210 are bore code 10, multiplied by 5 to give 50 mm."
      },
      {
        "q": "How much misalignment can 2210-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2210-ETN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2210-ETN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2210",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2210-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope, but catalogue C/C0 differ between executions (33.8/11.2 kN vs 22.9/8.15 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2210-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope, but catalogue C/C0 differ between executions (33.8/11.2 kN vs 22.9/8.15 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2210-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×23 mm envelope with catalogue ratings within 10 %; 2210 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2210-ETN9",
      "2210 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2210-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2210 EKTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 33.8,
    "static_load_kN": 11.2,
    "fatigue_load_limit_kN": 0.57,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2210 carries code 10 = 50 mm (code × 5). Envelope 50×90×23 mm (1.969×3.543×0.906 in) with a 20.0 mm radial section height, C 33.8 kN, C0 11.2 kN and Pu 0.57 kN. The open 2210 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 14000 r/min, limiting speed 9500 r/min, catalogue mass 600 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 2210-EKTN9 (C 33.8 kN, C0 11.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Catalogue ratings for 2210-EKTN9 (C 33.8 kN, C0 11.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The EKTN9 suffix on 2210-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 2210-EKTN9 (C 33.8 kN, C0 11.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 2210-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2210-EKTN9?",
        "a": "SKF 2210 EKTN9 measures 50 mm bore × 90 mm OD × 23 mm width (1.969 × 3.543 × 0.906 in), mass about 600 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2210 work?",
        "a": "The final two digits of 2210 are bore code 10, multiplied by 5 to give 50 mm."
      },
      {
        "q": "Can 2210-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2210-EKTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 90 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2210",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2210-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope, but catalogue C/C0 differ between executions (33.8/11.2 kN vs 22.9/8.15 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2210-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×23 mm envelope, but catalogue C/C0 differ between executions (33.8/11.2 kN vs 22.9/8.15 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2210-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×23 mm envelope with catalogue ratings within 10 %; 2210 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2210-EKTN9",
      "2210 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1310-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1310 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 43.6,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.72,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1310 carries code 10 = 50 mm (code × 5). Envelope 50×110×27 mm (1.969×4.331×1.063 in) with a 30.0 mm radial section height, C 43.6 kN, C0 14 kN and Pu 0.72 kN. The open 1310 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 50 mm shaft. Reference (thermal) speed 12000 r/min, limiting speed 8000 r/min, catalogue mass 1200 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The ETN9 suffix on 1310-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1310-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 50 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 1310-ETN9 (C 43.6 kN, C0 14 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1310-ETN9?",
        "a": "SKF 1310 ETN9 measures 50 mm bore × 110 mm OD × 27 mm width (1.969 × 4.331 × 1.063 in), mass about 1200 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1310 work?",
        "a": "The final two digits of 1310 are bore code 10, multiplied by 5 to give 50 mm."
      },
      {
        "q": "How much misalignment can 1310-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1310-ETN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 1310-ETN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1310",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1310-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 1310 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1310-ETN9",
      "1310 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1310-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1310 EKTN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 43.6,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.72,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1310 carries code 10 = 50 mm (code × 5). Envelope 50×110×27 mm (1.969×4.331×1.063 in) with a 30.0 mm radial section height, C 43.6 kN, C0 14 kN and Pu 0.72 kN. The open 1310 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 12000 r/min, limiting speed 8000 r/min, catalogue mass 1200 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 1310-EKTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Catalogue ratings for 1310-EKTN9 (C 43.6 kN, C0 14 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "On a sleeve-mounted 1310-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 1310-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 1310-EKTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 1310-EKTN9 chamfer so the 27 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1310-EKTN9?",
        "a": "SKF 1310 EKTN9 measures 50 mm bore × 110 mm OD × 27 mm width (1.969 × 4.331 × 1.063 in), mass about 1200 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1310 work?",
        "a": "The final two digits of 1310 are bore code 10, multiplied by 5 to give 50 mm."
      },
      {
        "q": "What is the speed rating of 1310-EKTN9?",
        "a": "SKF lists a 12000 r/min thermal reference speed and a 8000 r/min mechanical limiting speed for 1310 EKTN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1310-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1310-EKTN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1310",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1310-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 1310 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1310-EKTN9",
      "1310 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2310-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2310 E-2RS1TN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 43.6,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.72,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 1650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2310 carries code 10 = 50 mm (code × 5). Envelope 50×110×40 mm (1.969×4.331×1.575 in) with a 30.0 mm radial section height, C 43.6 kN, C0 14 kN and Pu 0.72 kN. SKF spells the sealed execution 2310 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 50 mm shaft. Limiting speed 4000 r/min, catalogue mass 1650 g.",
    "applications": [
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 2310-E-2RS1TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Assign interference to the rotating ring: on a 50 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The 2RS1 contact seals on 2310-E-2RS1TN9 add drag and cap speed at 4000 r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "The E-2RS1TN9 suffix on 2310-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 50 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2310-E-2RS1TN9 (C 43.6 kN, C0 14 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2310-E-2RS1TN9?",
        "a": "SKF 2310 E-2RS1TN9 measures 50 mm bore × 110 mm OD × 40 mm width (1.969 × 4.331 × 1.575 in), mass about 1650 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2310 work?",
        "a": "The final two digits of 2310 are bore code 10, multiplied by 5 to give 50 mm."
      },
      {
        "q": "What load can 2310-E-2RS1TN9 take?",
        "a": "Catalogue values for 2310 E-2RS1TN9: dynamic C 43.6 kN, static C0 14 kN, fatigue limit Pu 0.72 kN. Use C in life calculation and C0 for static checks at 50 mm bore."
      },
      {
        "q": "What is the speed rating of 2310-E-2RS1TN9?",
        "a": "SKF publishes only the 4000 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2310",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×110×40 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2310-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×40 mm envelope with catalogue ratings within 10 %; 2310 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2310-K",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×40 mm envelope, but catalogue C/C0 differ between executions (43.6/14 kN vs 63.7/20 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2310-E-2RS1TN9",
      "2310 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2310-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2310 E-2RS1KTN9",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 43.6,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.72,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 1650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2310 carries code 10 = 50 mm (code × 5). Envelope 50×110×40 mm (1.969×4.331×1.575 in) with a 30.0 mm radial section height, C 43.6 kN, C0 14 kN and Pu 0.72 kN. SKF spells the sealed execution 2310 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 4000 r/min, catalogue mass 1650 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.72 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The spherical outer raceway lets 2310-E-2RS1KTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2310-E-2RS1KTN9 to avoid seal-lip binding.",
      "The K suffix means a 1:12 tapered bore: 2310-E-2RS1KTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The E-2RS1KTN9 suffix on 2310-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2310-E-2RS1KTN9 chamfer so the 40 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2310-E-2RS1KTN9?",
        "a": "SKF 2310 E-2RS1KTN9 measures 50 mm bore × 110 mm OD × 40 mm width (1.969 × 4.331 × 1.575 in), mass about 1650 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2310 work?",
        "a": "The final two digits of 2310 are bore code 10, multiplied by 5 to give 50 mm."
      },
      {
        "q": "How heavy is 2310-E-2RS1KTN9?",
        "a": "Catalogue mass is 1650 g for 2310 E-2RS1KTN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2310-E-2RS1KTN9 take?",
        "a": "Catalogue values for 2310 E-2RS1KTN9: dynamic C 43.6 kN, static C0 14 kN, fatigue limit Pu 0.72 kN. Use C in life calculation and C0 for static checks at 50 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2310",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×110×40 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2310-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×40 mm envelope with catalogue ratings within 10 %; 2310 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2310-K",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×40 mm envelope, but catalogue C/C0 differ between executions (43.6/14 kN vs 63.7/20 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2310-E-2RS1KTN9",
      "2310 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2310-K",
    "brand": "SKF",
    "manufacturer_designation": "2310 K",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 63.7,
    "static_load_kN": 20,
    "fatigue_load_limit_kN": 1.04,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 1650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2310 carries code 10 = 50 mm (code × 5). Envelope 50×110×40 mm (1.969×4.331×1.575 in) with a 30.0 mm radial section height, C 63.7 kN, C0 20 kN and Pu 1.04 kN. The open 2310 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 14000 r/min, limiting speed 9500 r/min, catalogue mass 1650 g.",
    "applications": [
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 50 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Mount 2310-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The  suffix on 2310-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2310-K chamfer so the 40 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2310-K (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2310-K?",
        "a": "SKF 2310 K measures 50 mm bore × 110 mm OD × 40 mm width (1.969 × 4.331 × 1.575 in), mass about 1650 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2310 work?",
        "a": "The final two digits of 2310 are bore code 10, multiplied by 5 to give 50 mm."
      },
      {
        "q": "What load can 2310-K take?",
        "a": "Catalogue values for 2310 K: dynamic C 63.7 kN, static C0 20 kN, fatigue limit Pu 1.04 kN. Use C in life calculation and C0 for static checks at 50 mm bore."
      },
      {
        "q": "What is the speed rating of 2310-K?",
        "a": "SKF lists a 14000 r/min thermal reference speed and a 9500 r/min mechanical limiting speed for 2310 K; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2310",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2310-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×40 mm envelope, but catalogue C/C0 differ between executions (63.7/20 kN vs 43.6/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2310-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×40 mm envelope, but catalogue C/C0 differ between executions (63.7/20 kN vs 43.6/14 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2310-K",
      "2310 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1211-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1211 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 27.6,
    "static_load_kN": 10.6,
    "fatigue_load_limit_kN": 0.54,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 710,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1211 carries code 11 = 55 mm (code × 5). Envelope 55×100×21 mm (2.165×3.937×0.827 in) with a 22.5 mm radial section height, C 27.6 kN, C0 10.6 kN and Pu 0.54 kN. The open 1211 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 55 mm shaft. Reference (thermal) speed 14000 r/min, limiting speed 9000 r/min, catalogue mass 710 g.",
    "applications": [
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 55 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Assign interference to the rotating ring: on a 55 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The ETN9 suffix on 1211-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.54 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 55 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 1211-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1211-ETN9?",
        "a": "SKF 1211 ETN9 measures 55 mm bore × 100 mm OD × 21 mm width (2.165 × 3.937 × 0.827 in), mass about 710 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1211 work?",
        "a": "The final two digits of 1211 are bore code 11, multiplied by 5 to give 55 mm."
      },
      {
        "q": "What load can 1211-ETN9 take?",
        "a": "Catalogue values for 1211 ETN9: dynamic C 27.6 kN, static C0 10.6 kN, fatigue limit Pu 0.54 kN. Use C in life calculation and C0 for static checks at 55 mm bore."
      },
      {
        "q": "What is the speed rating of 1211-ETN9?",
        "a": "SKF lists a 14000 r/min thermal reference speed and a 9000 r/min mechanical limiting speed for 1211 ETN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1211",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1211-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 1211 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1211-ETN9",
      "1211 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1211-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1211 EKTN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 27.6,
    "static_load_kN": 10.6,
    "fatigue_load_limit_kN": 0.54,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 710,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1211 carries code 11 = 55 mm (code × 5). Envelope 55×100×21 mm (2.165×3.937×0.827 in) with a 22.5 mm radial section height, C 27.6 kN, C0 10.6 kN and Pu 0.54 kN. The open 1211 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 14000 r/min, limiting speed 9000 r/min, catalogue mass 710 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 1211-EKTN9 (C 27.6 kN, C0 10.6 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The spherical outer raceway lets 1211-EKTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The EKTN9 suffix on 1211-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 1211-EKTN9 (C 27.6 kN, C0 10.6 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1211-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1211-EKTN9?",
        "a": "SKF 1211 EKTN9 measures 55 mm bore × 100 mm OD × 21 mm width (2.165 × 3.937 × 0.827 in), mass about 710 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1211 work?",
        "a": "The final two digits of 1211 are bore code 11, multiplied by 5 to give 55 mm."
      },
      {
        "q": "Can 1211-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 1211-EKTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 100 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1211",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1211-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 1211 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1211-EKTN9",
      "1211 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2211-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2211 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 27.6,
    "static_load_kN": 10.6,
    "fatigue_load_limit_kN": 0.54,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 790,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2211 carries code 11 = 55 mm (code × 5). Envelope 55×100×25 mm (2.165×3.937×0.984 in) with a 22.5 mm radial section height, C 27.6 kN, C0 10.6 kN and Pu 0.54 kN. SKF spells the sealed execution 2211 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 55 mm shaft. Limiting speed 4300 r/min, catalogue mass 790 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2211-E-2RS1TN9 chamfer so the 25 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "At 55 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2211-E-2RS1TN9 to avoid seal-lip binding.",
      "The E-2RS1TN9 suffix on 2211-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 55 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 2211-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2211-E-2RS1TN9?",
        "a": "SKF 2211 E-2RS1TN9 measures 55 mm bore × 100 mm OD × 25 mm width (2.165 × 3.937 × 0.984 in), mass about 790 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2211 work?",
        "a": "The final two digits of 2211 are bore code 11, multiplied by 5 to give 55 mm."
      },
      {
        "q": "How much misalignment can 2211-E-2RS1TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2211-E-2RS1TN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2211-E-2RS1TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2211",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2211-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×25 mm envelope with catalogue ratings within 10 %; 2211 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2211-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope, but catalogue C/C0 differ between executions (27.6/10.6 kN vs 39/13.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2211-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope, but catalogue C/C0 differ between executions (27.6/10.6 kN vs 39/13.4 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2211-E-2RS1TN9",
      "2211 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2211-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2211 E-2RS1KTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 27.6,
    "static_load_kN": 10.6,
    "fatigue_load_limit_kN": 0.54,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 790,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2211 carries code 11 = 55 mm (code × 5). Envelope 55×100×25 mm (2.165×3.937×0.984 in) with a 22.5 mm radial section height, C 27.6 kN, C0 10.6 kN and Pu 0.54 kN. SKF spells the sealed execution 2211 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 4300 r/min, catalogue mass 790 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2211-E-2RS1KTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Catalogue ratings for 2211-E-2RS1KTN9 (C 27.6 kN, C0 10.6 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2211-E-2RS1KTN9 to avoid seal-lip binding.",
      "The K suffix means a 1:12 tapered bore: 2211-E-2RS1KTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The E-2RS1KTN9 suffix on 2211-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 2211-E-2RS1KTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2211-E-2RS1KTN9?",
        "a": "SKF 2211 E-2RS1KTN9 measures 55 mm bore × 100 mm OD × 25 mm width (2.165 × 3.937 × 0.984 in), mass about 790 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2211 work?",
        "a": "The final two digits of 2211 are bore code 11, multiplied by 5 to give 55 mm."
      },
      {
        "q": "How heavy is 2211-E-2RS1KTN9?",
        "a": "Catalogue mass is 790 g for 2211 E-2RS1KTN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2211-E-2RS1KTN9 take?",
        "a": "Catalogue values for 2211 E-2RS1KTN9: dynamic C 27.6 kN, static C0 10.6 kN, fatigue limit Pu 0.54 kN. Use C in life calculation and C0 for static checks at 55 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2211",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2211-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×25 mm envelope with catalogue ratings within 10 %; 2211 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2211-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope, but catalogue C/C0 differ between executions (27.6/10.6 kN vs 39/13.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2211-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope, but catalogue C/C0 differ between executions (27.6/10.6 kN vs 39/13.4 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2211-E-2RS1KTN9",
      "2211 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2211-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2211 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 39,
    "static_load_kN": 13.4,
    "fatigue_load_limit_kN": 0.7,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 810,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2211 carries code 11 = 55 mm (code × 5). Envelope 55×100×25 mm (2.165×3.937×0.984 in) with a 22.5 mm radial section height, C 39 kN, C0 13.4 kN and Pu 0.7 kN. The open 2211 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 55 mm shaft. Reference (thermal) speed 12000 r/min, limiting speed 8500 r/min, catalogue mass 810 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2211-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The spherical outer raceway lets 2211-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The ETN9 suffix on 2211-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 55 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 2211-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2211-ETN9 chamfer so the 25 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2211-ETN9?",
        "a": "SKF 2211 ETN9 measures 55 mm bore × 100 mm OD × 25 mm width (2.165 × 3.937 × 0.984 in), mass about 810 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2211 work?",
        "a": "The final two digits of 2211 are bore code 11, multiplied by 5 to give 55 mm."
      },
      {
        "q": "What is the speed rating of 2211-ETN9?",
        "a": "SKF lists a 12000 r/min thermal reference speed and a 8500 r/min mechanical limiting speed for 2211 ETN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 2211-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2211-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2211",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2211-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope, but catalogue C/C0 differ between executions (39/13.4 kN vs 27.6/10.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2211-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope, but catalogue C/C0 differ between executions (39/13.4 kN vs 27.6/10.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2211-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×25 mm envelope with catalogue ratings within 10 %; 2211 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2211-ETN9",
      "2211 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2211-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2211 EKTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 39,
    "static_load_kN": 13.4,
    "fatigue_load_limit_kN": 0.7,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 810,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2211 carries code 11 = 55 mm (code × 5). Envelope 55×100×25 mm (2.165×3.937×0.984 in) with a 22.5 mm radial section height, C 39 kN, C0 13.4 kN and Pu 0.7 kN. The open 2211 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 12000 r/min, limiting speed 8500 r/min, catalogue mass 810 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 55 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Fillet radii must clear the 2211-EKTN9 chamfer so the 25 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "On a sleeve-mounted 2211-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 2211-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2211-EKTN9 chamfer so the 25 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2211-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2211-EKTN9?",
        "a": "SKF 2211 EKTN9 measures 55 mm bore × 100 mm OD × 25 mm width (2.165 × 3.937 × 0.984 in), mass about 810 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2211 work?",
        "a": "The final two digits of 2211 are bore code 11, multiplied by 5 to give 55 mm."
      },
      {
        "q": "Which fits should I use for 2211-EKTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 100 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2211-EKTN9?",
        "a": "Catalogue mass is 810 g for 2211 EKTN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2211",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2211-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope, but catalogue C/C0 differ between executions (39/13.4 kN vs 27.6/10.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2211-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×25 mm envelope, but catalogue C/C0 differ between executions (39/13.4 kN vs 27.6/10.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2211-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×25 mm envelope with catalogue ratings within 10 %; 2211 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2211-EKTN9",
      "2211 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1311-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1311 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 50.7,
    "static_load_kN": 18,
    "fatigue_load_limit_kN": 0.92,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 1600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1311 carries code 11 = 55 mm (code × 5). Envelope 55×120×29 mm (2.165×4.724×1.142 in) with a 32.5 mm radial section height, C 50.7 kN, C0 18 kN and Pu 0.92 kN. The open 1311 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 55 mm shaft. Reference (thermal) speed 11000 r/min, limiting speed 7500 r/min, catalogue mass 1600 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.92 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The spherical outer raceway lets 1311-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The ETN9 suffix on 1311-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 55 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 1311-ETN9 (C 50.7 kN, C0 18 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1311-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1311-ETN9?",
        "a": "SKF 1311 ETN9 measures 55 mm bore × 120 mm OD × 29 mm width (2.165 × 4.724 × 1.142 in), mass about 1600 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1311 work?",
        "a": "The final two digits of 1311 are bore code 11, multiplied by 5 to give 55 mm."
      },
      {
        "q": "What is the speed rating of 1311-ETN9?",
        "a": "SKF lists a 11000 r/min thermal reference speed and a 7500 r/min mechanical limiting speed for 1311 ETN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1311-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1311-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1311",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1311-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 1311 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1311-ETN9",
      "1311 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1311-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1311 EKTN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 50.7,
    "static_load_kN": 18,
    "fatigue_load_limit_kN": 0.92,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 1600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1311 carries code 11 = 55 mm (code × 5). Envelope 55×120×29 mm (2.165×4.724×1.142 in) with a 32.5 mm radial section height, C 50.7 kN, C0 18 kN and Pu 0.92 kN. The open 1311 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 11000 r/min, limiting speed 7500 r/min, catalogue mass 1600 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 55 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the 1311-EKTN9 chamfer so the 29 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "On a sleeve-mounted 1311-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 1311-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 1311-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.92 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1311-EKTN9?",
        "a": "SKF 1311 EKTN9 measures 55 mm bore × 120 mm OD × 29 mm width (2.165 × 4.724 × 1.142 in), mass about 1600 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1311 work?",
        "a": "The final two digits of 1311 are bore code 11, multiplied by 5 to give 55 mm."
      },
      {
        "q": "Which fits should I use for 1311-EKTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 120 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 1311-EKTN9?",
        "a": "Catalogue mass is 1600 g for 1311 EKTN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1311",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1311-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 1311 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1311-EKTN9",
      "1311 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2311-K",
    "brand": "SKF",
    "manufacturer_designation": "2311 K",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 76.1,
    "static_load_kN": 24,
    "fatigue_load_limit_kN": 1.25,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 2100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2311 carries code 11 = 55 mm (code × 5). Envelope 55×120×43 mm (2.165×4.724×1.693 in) with a 32.5 mm radial section height, C 76.1 kN, C0 24 kN and Pu 1.25 kN. The open 2311 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 11000 r/min, limiting speed 7500 r/min, catalogue mass 2100 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 2311-K (C 76.1 kN, C0 24 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Catalogue ratings for 2311-K (C 76.1 kN, C0 24 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The K suffix means a 1:12 tapered bore: 2311-K is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The  suffix on 2311-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 2311-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2311-K chamfer so the 43 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2311-K?",
        "a": "SKF 2311 K measures 55 mm bore × 120 mm OD × 43 mm width (2.165 × 4.724 × 1.693 in), mass about 2100 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2311 work?",
        "a": "The final two digits of 2311 are bore code 11, multiplied by 5 to give 55 mm."
      },
      {
        "q": "How heavy is 2311-K?",
        "a": "Catalogue mass is 2100 g for 2311 K; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2311-K take?",
        "a": "Catalogue values for 2311 K: dynamic C 76.1 kN, static C0 24 kN, fatigue limit Pu 1.25 kN. Use C in life calculation and C0 for static checks at 55 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2311",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2311-K",
      "2311 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1212-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1212 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 31.2,
    "static_load_kN": 12.2,
    "fatigue_load_limit_kN": 0.62,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1212 carries code 12 = 60 mm (code × 5). Envelope 60×110×22 mm (2.362×4.331×0.866 in) with a 25.0 mm radial section height, C 31.2 kN, C0 12.2 kN and Pu 0.62 kN. The open 1212 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 60 mm shaft. Reference (thermal) speed 12000 r/min, limiting speed 8500 r/min, catalogue mass 900 g.",
    "applications": [
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 1212-ETN9 (C 31.2 kN, C0 12.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1212-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The ETN9 suffix on 1212-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 1212-ETN9 chamfer so the 22 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1212-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 60 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1212-ETN9?",
        "a": "SKF 1212 ETN9 measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 900 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1212 work?",
        "a": "The final two digits of 1212 are bore code 12, multiplied by 5 to give 60 mm."
      },
      {
        "q": "How heavy is 1212-ETN9?",
        "a": "Catalogue mass is 900 g for 1212 ETN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 1212-ETN9 take?",
        "a": "Catalogue values for 1212 ETN9: dynamic C 31.2 kN, static C0 12.2 kN, fatigue limit Pu 0.62 kN. Use C in life calculation and C0 for static checks at 60 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1212",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1212-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 1212 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11212-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 11212 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1212-ETN9",
      "1212 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1212-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1212 EKTN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 31.2,
    "static_load_kN": 12.2,
    "fatigue_load_limit_kN": 0.62,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1212 carries code 12 = 60 mm (code × 5). Envelope 60×110×22 mm (2.362×4.331×0.866 in) with a 25.0 mm radial section height, C 31.2 kN, C0 12.2 kN and Pu 0.62 kN. The open 1212 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 12000 r/min, limiting speed 8500 r/min, catalogue mass 900 g.",
    "applications": [
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 1212-EKTN9 chamfer so the 22 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring: on a 60 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The EKTN9 suffix on 1212-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 60 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 1212-EKTN9 (C 31.2 kN, C0 12.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1212-EKTN9?",
        "a": "SKF 1212 EKTN9 measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 900 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1212 work?",
        "a": "The final two digits of 1212 are bore code 12, multiplied by 5 to give 60 mm."
      },
      {
        "q": "What load can 1212-EKTN9 take?",
        "a": "Catalogue values for 1212 EKTN9: dynamic C 31.2 kN, static C0 12.2 kN, fatigue limit Pu 0.62 kN. Use C in life calculation and C0 for static checks at 60 mm bore."
      },
      {
        "q": "What is the speed rating of 1212-EKTN9?",
        "a": "SKF lists a 12000 r/min thermal reference speed and a 8500 r/min mechanical limiting speed for 1212 EKTN9; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1212",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1212-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 1212 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "11212-TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 11212 TN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1212-EKTN9",
      "1212 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2212-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2212 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 31.2,
    "static_load_kN": 12.2,
    "fatigue_load_limit_kN": 0.62,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 1050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2212 carries code 12 = 60 mm (code × 5). Envelope 60×110×28 mm (2.362×4.331×1.102 in) with a 25.0 mm radial section height, C 31.2 kN, C0 12.2 kN and Pu 0.62 kN. SKF spells the sealed execution 2212 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 60 mm shaft. Limiting speed 3800 r/min, catalogue mass 1050 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 2212-E-2RS1TN9 (C 31.2 kN, C0 12.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Catalogue ratings for 2212-E-2RS1TN9 (C 31.2 kN, C0 12.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2212-E-2RS1TN9 to avoid seal-lip binding.",
      "The E-2RS1TN9 suffix on 2212-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 3800 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 2212-E-2RS1TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2212-E-2RS1TN9 chamfer so the 28 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2212-E-2RS1TN9?",
        "a": "SKF 2212 E-2RS1TN9 measures 60 mm bore × 110 mm OD × 28 mm width (2.362 × 4.331 × 1.102 in), mass about 1050 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2212 work?",
        "a": "The final two digits of 2212 are bore code 12, multiplied by 5 to give 60 mm."
      },
      {
        "q": "How heavy is 2212-E-2RS1TN9?",
        "a": "Catalogue mass is 1050 g for 2212 E-2RS1TN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2212-E-2RS1TN9 take?",
        "a": "Catalogue values for 2212 E-2RS1TN9: dynamic C 31.2 kN, static C0 12.2 kN, fatigue limit Pu 0.62 kN. Use C in life calculation and C0 for static checks at 60 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2212",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2212-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×28 mm envelope with catalogue ratings within 10 %; 2212 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2212-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope, but catalogue C/C0 differ between executions (31.2/12.2 kN vs 48.8/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2212-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope, but catalogue C/C0 differ between executions (31.2/12.2 kN vs 48.8/17 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2212-E-2RS1TN9",
      "2212 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2212-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2212 E-2RS1KTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 31.2,
    "static_load_kN": 12.2,
    "fatigue_load_limit_kN": 0.62,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 1050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2212 carries code 12 = 60 mm (code × 5). Envelope 60×110×28 mm (2.362×4.331×1.102 in) with a 25.0 mm radial section height, C 31.2 kN, C0 12.2 kN and Pu 0.62 kN. SKF spells the sealed execution 2212 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 3800 r/min, catalogue mass 1050 g.",
    "applications": [
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2212-E-2RS1KTN9 chamfer so the 28 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Mount 2212-E-2RS1KTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2212-E-2RS1KTN9 to avoid seal-lip binding.",
      "The K suffix means a 1:12 tapered bore: 2212-E-2RS1KTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The E-2RS1KTN9 suffix on 2212-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 3800 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2212-E-2RS1KTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2212-E-2RS1KTN9?",
        "a": "SKF 2212 E-2RS1KTN9 measures 60 mm bore × 110 mm OD × 28 mm width (2.362 × 4.331 × 1.102 in), mass about 1050 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2212 work?",
        "a": "The final two digits of 2212 are bore code 12, multiplied by 5 to give 60 mm."
      },
      {
        "q": "How much misalignment can 2212-E-2RS1KTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2212-E-2RS1KTN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2212-E-2RS1KTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2212",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "2212-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×28 mm envelope with catalogue ratings within 10 %; 2212 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2212-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope, but catalogue C/C0 differ between executions (31.2/12.2 kN vs 48.8/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2212-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope, but catalogue C/C0 differ between executions (31.2/12.2 kN vs 48.8/17 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2212-E-2RS1KTN9",
      "2212 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2212-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2212 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 48.8,
    "static_load_kN": 17,
    "fatigue_load_limit_kN": 0.88,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2212 carries code 12 = 60 mm (code × 5). Envelope 60×110×28 mm (2.362×4.331×1.102 in) with a 25.0 mm radial section height, C 48.8 kN, C0 17 kN and Pu 0.88 kN. The open 2212 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 60 mm shaft. Reference (thermal) speed 11000 r/min, limiting speed 8000 r/min, catalogue mass 1100 g.",
    "applications": [
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 2212-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Mount 2212-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The ETN9 suffix on 2212-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 2212-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 2212-ETN9 chamfer so the 28 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2212-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2212-ETN9?",
        "a": "SKF 2212 ETN9 measures 60 mm bore × 110 mm OD × 28 mm width (2.362 × 4.331 × 1.102 in), mass about 1100 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2212 work?",
        "a": "The final two digits of 2212 are bore code 12, multiplied by 5 to give 60 mm."
      },
      {
        "q": "Which fits should I use for 2212-ETN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 110 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2212-ETN9?",
        "a": "Catalogue mass is 1100 g for 2212 ETN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2212",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2212-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope, but catalogue C/C0 differ between executions (48.8/17 kN vs 31.2/12.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2212-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope, but catalogue C/C0 differ between executions (48.8/17 kN vs 31.2/12.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2212-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×28 mm envelope with catalogue ratings within 10 %; 2212 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2212-ETN9",
      "2212 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2212-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2212 EKTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 48.8,
    "static_load_kN": 17,
    "fatigue_load_limit_kN": 0.88,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2212 carries code 12 = 60 mm (code × 5). Envelope 60×110×28 mm (2.362×4.331×1.102 in) with a 25.0 mm radial section height, C 48.8 kN, C0 17 kN and Pu 0.88 kN. The open 2212 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 11000 r/min, limiting speed 8000 r/min, catalogue mass 1100 g.",
    "applications": [
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.88 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2212-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "On a sleeve-mounted 2212-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 2212-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.88 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 60 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2212-EKTN9?",
        "a": "SKF 2212 EKTN9 measures 60 mm bore × 110 mm OD × 28 mm width (2.362 × 4.331 × 1.102 in), mass about 1100 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2212 work?",
        "a": "The final two digits of 2212 are bore code 12, multiplied by 5 to give 60 mm."
      },
      {
        "q": "What is the speed rating of 2212-EKTN9?",
        "a": "SKF lists a 11000 r/min thermal reference speed and a 8000 r/min mechanical limiting speed for 2212 EKTN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 2212-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2212-EKTN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2212",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2212-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope, but catalogue C/C0 differ between executions (48.8/17 kN vs 31.2/12.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2212-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×28 mm envelope, but catalogue C/C0 differ between executions (48.8/17 kN vs 31.2/12.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2212-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×28 mm envelope with catalogue ratings within 10 %; 2212 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2212-EKTN9",
      "2212 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1312-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1312 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 58.5,
    "static_load_kN": 22,
    "fatigue_load_limit_kN": 1.12,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1312 carries code 12 = 60 mm (code × 5). Envelope 60×130×31 mm (2.362×5.118×1.22 in) with a 35.0 mm radial section height, C 58.5 kN, C0 22 kN and Pu 1.12 kN. The open 1312 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 60 mm shaft. Reference (thermal) speed 9000 r/min, limiting speed 6300 r/min, catalogue mass 1950 g.",
    "applications": [
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 1312-ETN9 chamfer so the 31 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Mount 1312-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The ETN9 suffix on 1312-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 1312-ETN9 (C 58.5 kN, C0 22 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1312-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 1.12 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1312-ETN9?",
        "a": "SKF 1312 ETN9 measures 60 mm bore × 130 mm OD × 31 mm width (2.362 × 5.118 × 1.22 in), mass about 1950 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1312 work?",
        "a": "The final two digits of 1312 are bore code 12, multiplied by 5 to give 60 mm."
      },
      {
        "q": "How much misalignment can 1312-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1312-ETN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 1312-ETN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1312",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1312-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 1312 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1312-ETN9",
      "1312 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1312-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1312 EKTN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 58.5,
    "static_load_kN": 22,
    "fatigue_load_limit_kN": 1.12,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1312 carries code 12 = 60 mm (code × 5). Envelope 60×130×31 mm (2.362×5.118×1.22 in) with a 35.0 mm radial section height, C 58.5 kN, C0 22 kN and Pu 1.12 kN. The open 1312 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 9000 r/min, limiting speed 6300 r/min, catalogue mass 1950 g.",
    "applications": [
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1312-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1312-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "On a sleeve-mounted 1312-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 1312-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1312-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 60 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1312-EKTN9?",
        "a": "SKF 1312 EKTN9 measures 60 mm bore × 130 mm OD × 31 mm width (2.362 × 5.118 × 1.22 in), mass about 1950 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1312 work?",
        "a": "The final two digits of 1312 are bore code 12, multiplied by 5 to give 60 mm."
      },
      {
        "q": "What is the speed rating of 1312-EKTN9?",
        "a": "SKF lists a 9000 r/min thermal reference speed and a 6300 r/min mechanical limiting speed for 1312 EKTN9; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1312-EKTN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1312-EKTN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1312",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1312-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 1312 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1312-EKTN9",
      "1312 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2312-K",
    "brand": "SKF",
    "manufacturer_designation": "2312 K",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 87.1,
    "static_load_kN": 28.5,
    "fatigue_load_limit_kN": 1.46,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 2600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2312 carries code 12 = 60 mm (code × 5). Envelope 60×130×46 mm (2.362×5.118×1.811 in) with a 35.0 mm radial section height, C 87.1 kN, C0 28.5 kN and Pu 1.46 kN. The open 2312 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 9500 r/min, limiting speed 7000 r/min, catalogue mass 2600 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2312-K chamfer so the 46 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "At 60 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The K suffix means a 1:12 tapered bore: 2312-K is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The  suffix on 2312-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 60 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 2312-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2312-K?",
        "a": "SKF 2312 K measures 60 mm bore × 130 mm OD × 46 mm width (2.362 × 5.118 × 1.811 in), mass about 2600 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2312 work?",
        "a": "The final two digits of 2312 are bore code 12, multiplied by 5 to give 60 mm."
      },
      {
        "q": "How much misalignment can 2312-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2312-K allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2312-K take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2312",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2312-K",
      "2312 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1213-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1213 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 35.1,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.72,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 1150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1213 carries code 13 = 65 mm (code × 5). Envelope 65×120×23 mm (2.559×4.724×0.906 in) with a 27.5 mm radial section height, C 35.1 kN, C0 14 kN and Pu 0.72 kN. The open 1213 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 65 mm shaft. Reference (thermal) speed 11000 r/min, limiting speed 7000 r/min, catalogue mass 1150 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 1213-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Fillet radii must clear the 1213-ETN9 chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The ETN9 suffix on 1213-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 1213-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 1213-ETN9 chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1213-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1213-ETN9?",
        "a": "SKF 1213 ETN9 measures 65 mm bore × 120 mm OD × 23 mm width (2.559 × 4.724 × 0.906 in), mass about 1150 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1213 work?",
        "a": "The final two digits of 1213 are bore code 13, multiplied by 5 to give 65 mm."
      },
      {
        "q": "Which fits should I use for 1213-ETN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 120 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 1213-ETN9?",
        "a": "Catalogue mass is 1150 g for 1213 ETN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1213",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1213-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 1213 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1213-ETN9",
      "1213 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1213-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1213 EKTN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 35.1,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.72,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 1150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1213 carries code 13 = 65 mm (code × 5). Envelope 65×120×23 mm (2.559×4.724×0.906 in) with a 27.5 mm radial section height, C 35.1 kN, C0 14 kN and Pu 0.72 kN. The open 1213 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 11000 r/min, limiting speed 7000 r/min, catalogue mass 1150 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.72 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The fatigue load limit is 0.72 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The EKTN9 suffix on 1213-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.72 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 65 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1213-EKTN9?",
        "a": "SKF 1213 EKTN9 measures 65 mm bore × 120 mm OD × 23 mm width (2.559 × 4.724 × 0.906 in), mass about 1150 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1213 work?",
        "a": "The final two digits of 1213 are bore code 13, multiplied by 5 to give 65 mm."
      },
      {
        "q": "Can 1213-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 1213-EKTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 120 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1213",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1213-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 1213 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1213-EKTN9",
      "1213 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2213-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2213 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 35.1,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.72,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 1400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2213 carries code 13 = 65 mm (code × 5). Envelope 65×120×31 mm (2.559×4.724×1.22 in) with a 27.5 mm radial section height, C 35.1 kN, C0 14 kN and Pu 0.72 kN. SKF spells the sealed execution 2213 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 65 mm shaft. Limiting speed 3600 r/min, catalogue mass 1400 g.",
    "applications": [
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives"
    ],
    "failure_modes": [
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 65 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Mount 2213-E-2RS1TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Do not wash 2213-E-2RS1TN9 with solvent — the lifetime grease fill is sealed in, and solvent destroys the grease without a way to repack it.",
      "The E-2RS1TN9 suffix on 2213-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 3600 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2213-E-2RS1TN9 chamfer so the 31 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2213-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2213-E-2RS1TN9?",
        "a": "SKF 2213 E-2RS1TN9 measures 65 mm bore × 120 mm OD × 31 mm width (2.559 × 4.724 × 1.22 in), mass about 1400 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2213 work?",
        "a": "The final two digits of 2213 are bore code 13, multiplied by 5 to give 65 mm."
      },
      {
        "q": "Which fits should I use for 2213-E-2RS1TN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 120 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2213-E-2RS1TN9?",
        "a": "Catalogue mass is 1400 g for 2213 E-2RS1TN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2213",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2213-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×31 mm envelope with catalogue ratings within 10 %; 2213 E-2RS1KTN9 is the glass-fibre PA66 cage, two contact elastomer seals, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2213-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope, but catalogue C/C0 differ between executions (35.1/14 kN vs 57.2/20 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2213-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope, but catalogue C/C0 differ between executions (35.1/14 kN vs 57.2/20 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2213-E-2RS1TN9",
      "2213 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2213-E-2RS1KTN9",
    "brand": "SKF",
    "manufacturer_designation": "2213 E-2RS1KTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 35.1,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.72,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 1400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2213 carries code 13 = 65 mm (code × 5). Envelope 65×120×31 mm (2.559×4.724×1.22 in) with a 27.5 mm radial section height, C 35.1 kN, C0 14 kN and Pu 0.72 kN. SKF spells the sealed execution 2213 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 3600 r/min, catalogue mass 1400 g.",
    "applications": [
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture passing a worn seal lip in dirty or wet duty",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 2213-E-2RS1KTN9 (C 35.1 kN, C0 14 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2213-E-2RS1KTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2213-E-2RS1KTN9 to avoid seal-lip binding.",
      "The K suffix means a 1:12 tapered bore: 2213-E-2RS1KTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The E-2RS1KTN9 suffix on 2213-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 3600 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 65 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2213-E-2RS1KTN9?",
        "a": "SKF 2213 E-2RS1KTN9 measures 65 mm bore × 120 mm OD × 31 mm width (2.559 × 4.724 × 1.22 in), mass about 1400 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2213 work?",
        "a": "The final two digits of 2213 are bore code 13, multiplied by 5 to give 65 mm."
      },
      {
        "q": "How heavy is 2213-E-2RS1KTN9?",
        "a": "Catalogue mass is 1400 g for 2213 E-2RS1KTN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2213-E-2RS1KTN9 take?",
        "a": "Catalogue values for 2213 E-2RS1KTN9: dynamic C 35.1 kN, static C0 14 kN, fatigue limit Pu 0.72 kN. Use C in life calculation and C0 for static checks at 65 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2213",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "2213-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×31 mm envelope with catalogue ratings within 10 %; 2213 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "2213-ETN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope, but catalogue C/C0 differ between executions (35.1/14 kN vs 57.2/20 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2213-EKTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope, but catalogue C/C0 differ between executions (35.1/14 kN vs 57.2/20 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2213-E-2RS1KTN9",
      "2213 E-2RS1KTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2213-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2213 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 57.2,
    "static_load_kN": 20,
    "fatigue_load_limit_kN": 1.02,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2213 carries code 13 = 65 mm (code × 5). Envelope 65×120×31 mm (2.559×4.724×1.22 in) with a 27.5 mm radial section height, C 57.2 kN, C0 20 kN and Pu 1.02 kN. The open 2213 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 65 mm shaft. Reference (thermal) speed 10000 r/min, limiting speed 7000 r/min, catalogue mass 1450 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 2213-ETN9 (C 57.2 kN, C0 20 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The fatigue load limit is 1.02 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The ETN9 suffix on 2213-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2213-ETN9 chamfer so the 31 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2213-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 65 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2213-ETN9?",
        "a": "SKF 2213 ETN9 measures 65 mm bore × 120 mm OD × 31 mm width (2.559 × 4.724 × 1.22 in), mass about 1450 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2213 work?",
        "a": "The final two digits of 2213 are bore code 13, multiplied by 5 to give 65 mm."
      },
      {
        "q": "Can 2213-ETN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2213-ETN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 120 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2213",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2213-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope, but catalogue C/C0 differ between executions (57.2/20 kN vs 35.1/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2213-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope, but catalogue C/C0 differ between executions (57.2/20 kN vs 35.1/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2213-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×31 mm envelope with catalogue ratings within 10 %; 2213 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2213-ETN9",
      "2213 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2213-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2213 EKTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 57.2,
    "static_load_kN": 20,
    "fatigue_load_limit_kN": 1.02,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2213 carries code 13 = 65 mm (code × 5). Envelope 65×120×31 mm (2.559×4.724×1.22 in) with a 27.5 mm radial section height, C 57.2 kN, C0 20 kN and Pu 1.02 kN. The open 2213 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 10000 r/min, limiting speed 7000 r/min, catalogue mass 1450 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2213-EKTN9 chamfer so the 31 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "At 65 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "On a sleeve-mounted 2213-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 2213-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 65 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2213-EKTN9 (C 57.2 kN, C0 20 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2213-EKTN9?",
        "a": "SKF 2213 EKTN9 measures 65 mm bore × 120 mm OD × 31 mm width (2.559 × 4.724 × 1.22 in), mass about 1450 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2213 work?",
        "a": "The final two digits of 2213 are bore code 13, multiplied by 5 to give 65 mm."
      },
      {
        "q": "Which fits should I use for 2213-EKTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 120 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2213-EKTN9?",
        "a": "Catalogue mass is 1450 g for 2213 EKTN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2213",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2213-E-2RS1TN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope, but catalogue C/C0 differ between executions (57.2/20 kN vs 35.1/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2213-E-2RS1KTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×31 mm envelope, but catalogue C/C0 differ between executions (57.2/20 kN vs 35.1/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "2213-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×31 mm envelope with catalogue ratings within 10 %; 2213 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2213-EKTN9",
      "2213 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1313-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1313 ETN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 65,
    "static_load_kN": 25.5,
    "fatigue_load_limit_kN": 1.25,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 2450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1313 carries code 13 = 65 mm (code × 5). Envelope 65×140×33 mm (2.559×5.512×1.299 in) with a 37.5 mm radial section height, C 65 kN, C0 25.5 kN and Pu 1.25 kN. The open 1313 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 65 mm shaft. Reference (thermal) speed 8500 r/min, limiting speed 6000 r/min, catalogue mass 2450 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 1313-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The fatigue load limit is 1.25 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The ETN9 suffix on 1313-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 1313-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 1.25 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 65 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1313-ETN9?",
        "a": "SKF 1313 ETN9 measures 65 mm bore × 140 mm OD × 33 mm width (2.559 × 5.512 × 1.299 in), mass about 2450 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1313 work?",
        "a": "The final two digits of 1313 are bore code 13, multiplied by 5 to give 65 mm."
      },
      {
        "q": "How heavy is 1313-ETN9?",
        "a": "Catalogue mass is 2450 g for 1313 ETN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 1313-ETN9 take?",
        "a": "Catalogue values for 1313 ETN9: dynamic C 65 kN, static C0 25.5 kN, fatigue limit Pu 1.25 kN. Use C in life calculation and C0 for static checks at 65 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1313",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1313-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 1313 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1313-ETN9",
      "1313 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1313-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "1313 EKTN9",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 65,
    "static_load_kN": 25.5,
    "fatigue_load_limit_kN": 1.25,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 2450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1313 carries code 13 = 65 mm (code × 5). Envelope 65×140×33 mm (2.559×5.512×1.299 in) with a 37.5 mm radial section height, C 65 kN, C0 25.5 kN and Pu 1.25 kN. The open 1313 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 8500 r/min, limiting speed 6000 r/min, catalogue mass 2450 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 1313-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "At 65 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "On a sleeve-mounted 1313-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 1313-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 65 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 1313-EKTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1313-EKTN9?",
        "a": "SKF 1313 EKTN9 measures 65 mm bore × 140 mm OD × 33 mm width (2.559 × 5.512 × 1.299 in), mass about 2450 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1313 work?",
        "a": "The final two digits of 1313 are bore code 13, multiplied by 5 to give 65 mm."
      },
      {
        "q": "Which fits should I use for 1313-EKTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 140 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 1313-EKTN9?",
        "a": "Catalogue mass is 2450 g for 1313 EKTN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1313",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "1313-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 1313 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1313-EKTN9",
      "1313 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2313-K",
    "brand": "SKF",
    "manufacturer_designation": "2313 K",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 48,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 95.6,
    "static_load_kN": 32.5,
    "fatigue_load_limit_kN": 1.66,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 3250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2313 carries code 13 = 65 mm (code × 5). Envelope 65×140×48 mm (2.559×5.512×1.89 in) with a 37.5 mm radial section height, C 95.6 kN, C0 32.5 kN and Pu 1.66 kN. The open 2313 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 9000 r/min, limiting speed 6300 r/min, catalogue mass 3250 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2313-K (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The fatigue load limit is 1.66 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The K suffix means a 1:12 tapered bore: 2313-K is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The  suffix on 2313-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 1.66 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 65 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2313-K?",
        "a": "SKF 2313 K measures 65 mm bore × 140 mm OD × 48 mm width (2.559 × 5.512 × 1.89 in), mass about 3250 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2313 work?",
        "a": "The final two digits of 2313 are bore code 13, multiplied by 5 to give 65 mm."
      },
      {
        "q": "How heavy is 2313-K?",
        "a": "Catalogue mass is 3250 g for 2313 K; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2313-K take?",
        "a": "Catalogue values for 2313 K: dynamic C 95.6 kN, static C0 32.5 kN, fatigue limit Pu 1.66 kN. Use C in life calculation and C0 for static checks at 65 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2313",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2313-K",
      "2313 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1214-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "1214 ETN9",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 35.8,
    "static_load_kN": 14.6,
    "fatigue_load_limit_kN": 0.75,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 1250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1214 carries code 14 = 70 mm (code × 5). Envelope 70×125×24 mm (2.756×4.921×0.945 in) with a 27.5 mm radial section height, C 35.8 kN, C0 14.6 kN and Pu 0.75 kN. The open 1214 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 70 mm shaft. Reference (thermal) speed 11000 r/min, limiting speed 7000 r/min, catalogue mass 1250 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.75 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The spherical outer raceway lets 1214-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The ETN9 suffix on 1214-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 7000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 70 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 1214-ETN9 (C 35.8 kN, C0 14.6 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1214-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1214-ETN9?",
        "a": "SKF 1214 ETN9 measures 70 mm bore × 125 mm OD × 24 mm width (2.756 × 4.921 × 0.945 in), mass about 1250 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1214 work?",
        "a": "The final two digits of 1214 are bore code 14, multiplied by 5 to give 70 mm."
      },
      {
        "q": "How heavy is 1214-ETN9?",
        "a": "Catalogue mass is 1250 g for 1214 ETN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 1214-ETN9 take?",
        "a": "Catalogue values for 1214 ETN9: dynamic C 35.8 kN, static C0 14.6 kN, fatigue limit Pu 0.75 kN. Use C in life calculation and C0 for static checks at 70 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1214",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1214-ETN9",
      "1214 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2214-E-2RS1TN9",
    "brand": "SKF",
    "manufacturer_designation": "2214 E-2RS1TN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 35.8,
    "static_load_kN": 14.6,
    "fatigue_load_limit_kN": 0.75,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2214 carries code 14 = 70 mm (code × 5). Envelope 70×125×31 mm (2.756×4.921×1.22 in) with a 27.5 mm radial section height, C 35.8 kN, C0 14.6 kN and Pu 0.75 kN. SKF spells the sealed execution 2214 E-2RS1TN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 70 mm shaft. Limiting speed 3400 r/min, catalogue mass 1450 g.",
    "applications": [
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.75 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2214-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The 2RS1 contact seals on 2214-E-2RS1TN9 add drag and cap speed at 3400 r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "The E-2RS1TN9 suffix on 2214-E-2RS1TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 3400 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2214-E-2RS1TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 70 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2214-E-2RS1TN9?",
        "a": "SKF 2214 E-2RS1TN9 measures 70 mm bore × 125 mm OD × 31 mm width (2.756 × 4.921 × 1.22 in), mass about 1450 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How does the bore code in 2214 work?",
        "a": "The final two digits of 2214 are bore code 14, multiplied by 5 to give 70 mm."
      },
      {
        "q": "Can 2214-E-2RS1TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2214-E-2RS1TN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 125 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2214",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 70×125×31 mm envelope per ISO 15; seal variant (2RS vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2214-E-2RS1TN9",
      "2214 E-2RS1TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1215-K",
    "brand": "SKF",
    "manufacturer_designation": "1215 K",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 39,
    "static_load_kN": 15.6,
    "fatigue_load_limit_kN": 0.8,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 1350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1215 carries code 15 = 75 mm (code × 5). Envelope 75×130×25 mm (2.953×5.118×0.984 in) with a 27.5 mm radial section height, C 39 kN, C0 15.6 kN and Pu 0.8 kN. The open 1215 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 10000 r/min, limiting speed 6700 r/min, catalogue mass 1350 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 1215-K (C 39 kN, C0 15.6 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The spherical outer raceway lets 1215-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "On a sleeve-mounted 1215-K, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The  suffix on 1215-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6700 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 1215-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 1215-K chamfer so the 25 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1215-K?",
        "a": "SKF 1215 K measures 75 mm bore × 130 mm OD × 25 mm width (2.953 × 5.118 × 0.984 in), mass about 1350 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1215 work?",
        "a": "The final two digits of 1215 are bore code 15, multiplied by 5 to give 75 mm."
      },
      {
        "q": "What is the speed rating of 1215-K?",
        "a": "SKF lists a 10000 r/min thermal reference speed and a 6700 r/min mechanical limiting speed for 1215 K; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1215-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1215-K allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1215",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1215-K",
      "1215 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2215-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2215 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 58.5,
    "static_load_kN": 22,
    "fatigue_load_limit_kN": 1.12,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2215 carries code 15 = 75 mm (code × 5). Envelope 75×130×31 mm (2.953×5.118×1.22 in) with a 27.5 mm radial section height, C 58.5 kN, C0 22 kN and Pu 1.12 kN. The open 2215 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 75 mm shaft. Reference (thermal) speed 9000 r/min, limiting speed 6300 r/min, catalogue mass 1600 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 1.12 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Catalogue ratings for 2215-ETN9 (C 58.5 kN, C0 22 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The ETN9 suffix on 2215-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 75 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2215-ETN9 (C 58.5 kN, C0 22 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 2215-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2215-ETN9?",
        "a": "SKF 2215 ETN9 measures 75 mm bore × 130 mm OD × 31 mm width (2.953 × 5.118 × 1.22 in), mass about 1600 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2215 work?",
        "a": "The final two digits of 2215 are bore code 15, multiplied by 5 to give 75 mm."
      },
      {
        "q": "How heavy is 2215-ETN9?",
        "a": "Catalogue mass is 1600 g for 2215 ETN9; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2215-ETN9 take?",
        "a": "Catalogue values for 2215 ETN9: dynamic C 58.5 kN, static C0 22 kN, fatigue limit Pu 1.12 kN. Use C in life calculation and C0 for static checks at 75 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2215",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×130×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2215-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×31 mm envelope with catalogue ratings within 10 %; 2215 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2215-ETN9",
      "2215 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2215-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2215 EKTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 58.5,
    "static_load_kN": 22,
    "fatigue_load_limit_kN": 1.12,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2215 carries code 15 = 75 mm (code × 5). Envelope 75×130×31 mm (2.953×5.118×1.22 in) with a 27.5 mm radial section height, C 58.5 kN, C0 22 kN and Pu 1.12 kN. The open 2215 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 9000 r/min, limiting speed 6300 r/min, catalogue mass 1600 g.",
    "applications": [
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 75 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Mount 2215-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "On a sleeve-mounted 2215-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The EKTN9 suffix on 2215-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 2215-EKTN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 1.12 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2215-EKTN9?",
        "a": "SKF 2215 EKTN9 measures 75 mm bore × 130 mm OD × 31 mm width (2.953 × 5.118 × 1.22 in), mass about 1600 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2215 work?",
        "a": "The final two digits of 2215 are bore code 15, multiplied by 5 to give 75 mm."
      },
      {
        "q": "Which fits should I use for 2215-EKTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 130 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2215-EKTN9?",
        "a": "Catalogue mass is 1600 g for 2215 EKTN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2215",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×130×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2215-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×31 mm envelope with catalogue ratings within 10 %; 2215 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2215-EKTN9",
      "2215 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1315-K",
    "brand": "SKF",
    "manufacturer_designation": "1315 K",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 79.3,
    "static_load_kN": 30,
    "fatigue_load_limit_kN": 1.43,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 3550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1315 carries code 15 = 75 mm (code × 5). Envelope 75×160×37 mm (2.953×6.299×1.457 in) with a 42.5 mm radial section height, C 79.3 kN, C0 30 kN and Pu 1.43 kN. The open 1315 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 8000 r/min, limiting speed 5600 r/min, catalogue mass 3550 g.",
    "applications": [
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 75 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Mount 1315-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The  suffix on 1315-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5600 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 1315-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 1.43 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1315-K?",
        "a": "SKF 1315 K measures 75 mm bore × 160 mm OD × 37 mm width (2.953 × 6.299 × 1.457 in), mass about 3550 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1315 work?",
        "a": "The final two digits of 1315 are bore code 15, multiplied by 5 to give 75 mm."
      },
      {
        "q": "What load can 1315-K take?",
        "a": "Catalogue values for 1315 K: dynamic C 79.3 kN, static C0 30 kN, fatigue limit Pu 1.43 kN. Use C in life calculation and C0 for static checks at 75 mm bore."
      },
      {
        "q": "What is the speed rating of 1315-K?",
        "a": "SKF lists a 8000 r/min thermal reference speed and a 5600 r/min mechanical limiting speed for 1315 K; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1315",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1315-K",
      "1315 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2315-K",
    "brand": "SKF",
    "manufacturer_designation": "2315 K",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 124,
    "static_load_kN": 43,
    "fatigue_load_limit_kN": 2.04,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 4700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2315 carries code 15 = 75 mm (code × 5). Envelope 75×160×55 mm (2.953×6.299×2.165 in) with a 42.5 mm radial section height, C 124 kN, C0 43 kN and Pu 2.04 kN. The open 2315 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 7500 r/min, limiting speed 5600 r/min, catalogue mass 4700 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2315-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The spherical outer raceway lets 2315-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "On a sleeve-mounted 2315-K, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The  suffix on 2315-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5600 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 2315-K (C 124 kN, C0 43 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 2315-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2315-K?",
        "a": "SKF 2315 K measures 75 mm bore × 160 mm OD × 55 mm width (2.953 × 6.299 × 2.165 in), mass about 4700 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2315 work?",
        "a": "The final two digits of 2315 are bore code 15, multiplied by 5 to give 75 mm."
      },
      {
        "q": "What is the speed rating of 2315-K?",
        "a": "SKF lists a 7500 r/min thermal reference speed and a 5600 r/min mechanical limiting speed for 2315 K; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 2315-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2315-K allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2315",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2315-K",
      "2315 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1216-K",
    "brand": "SKF",
    "manufacturer_designation": "1216 K",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 39.7,
    "static_load_kN": 17,
    "fatigue_load_limit_kN": 0.83,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 1650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1216 carries code 16 = 80 mm (code × 5). Envelope 80×140×26 mm (3.15×5.512×1.024 in) with a 30.0 mm radial section height, C 39.7 kN, C0 17 kN and Pu 0.83 kN. The open 1216 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 9500 r/min, limiting speed 6000 r/min, catalogue mass 1650 g.",
    "applications": [
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 1216-K chamfer so the 26 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring: on a 80 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "On a sleeve-mounted 1216-K, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The  suffix on 1216-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 80 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 1216-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1216-K?",
        "a": "SKF 1216 K measures 80 mm bore × 140 mm OD × 26 mm width (3.15 × 5.512 × 1.024 in), mass about 1650 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1216 work?",
        "a": "The final two digits of 1216 are bore code 16, multiplied by 5 to give 80 mm."
      },
      {
        "q": "Which fits should I use for 1216-K?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 140 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 1216-K?",
        "a": "Catalogue mass is 1650 g for 1216 K; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1216",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1216-K",
      "1216 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2216-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "2216 ETN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 65,
    "static_load_kN": 25.5,
    "fatigue_load_limit_kN": 1.25,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 2000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2216 carries code 16 = 80 mm (code × 5). Envelope 80×140×33 mm (3.15×5.512×1.299 in) with a 30.0 mm radial section height, C 65 kN, C0 25.5 kN and Pu 1.25 kN. The open 2216 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 80 mm shaft. Reference (thermal) speed 8500 r/min, limiting speed 6000 r/min, catalogue mass 2000 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2216-ETN9 chamfer so the 33 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Fillet radii must clear the 2216-ETN9 chamfer so the 33 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The ETN9 suffix on 2216-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 2216-ETN9 (C 65 kN, C0 25.5 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 2216-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 1.25 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2216-ETN9?",
        "a": "SKF 2216 ETN9 measures 80 mm bore × 140 mm OD × 33 mm width (3.15 × 5.512 × 1.299 in), mass about 2000 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2216 work?",
        "a": "The final two digits of 2216 are bore code 16, multiplied by 5 to give 80 mm."
      },
      {
        "q": "How much misalignment can 2216-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2216-ETN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2216-ETN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2216",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2216-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×33 mm envelope with catalogue ratings within 10 %; 2216 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2216-ETN9",
      "2216 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2216-EKTN9",
    "brand": "SKF",
    "manufacturer_designation": "2216 EKTN9",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 65,
    "static_load_kN": 25.5,
    "fatigue_load_limit_kN": 1.25,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 2000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2216 carries code 16 = 80 mm (code × 5). Envelope 80×140×33 mm (3.15×5.512×1.299 in) with a 30.0 mm radial section height, C 65 kN, C0 25.5 kN and Pu 1.25 kN. The open 2216 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 8500 r/min, limiting speed 6000 r/min, catalogue mass 2000 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2216-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The fatigue load limit is 1.25 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The EKTN9 suffix on 2216-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2216-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 80 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2216-EKTN9?",
        "a": "SKF 2216 EKTN9 measures 80 mm bore × 140 mm OD × 33 mm width (3.15 × 5.512 × 1.299 in), mass about 2000 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2216 work?",
        "a": "The final two digits of 2216 are bore code 16, multiplied by 5 to give 80 mm."
      },
      {
        "q": "Can 2216-EKTN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2216-EKTN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 140 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2216",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "2216-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×33 mm envelope with catalogue ratings within 10 %; 2216 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2216-EKTN9",
      "2216 EKTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1316-K",
    "brand": "SKF",
    "manufacturer_designation": "1316 K",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 88.4,
    "static_load_kN": 33.5,
    "fatigue_load_limit_kN": 1.5,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 4200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1316 carries code 16 = 80 mm (code × 5). Envelope 80×170×39 mm (3.15×6.693×1.535 in) with a 45.0 mm radial section height, C 88.4 kN, C0 33.5 kN and Pu 1.5 kN. The open 1316 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 7500 r/min, limiting speed 5300 r/min, catalogue mass 4200 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 1.5 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The fatigue load limit is 1.5 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "On a sleeve-mounted 1316-K, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The  suffix on 1316-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1316-K (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 80 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1316-K?",
        "a": "SKF 1316 K measures 80 mm bore × 170 mm OD × 39 mm width (3.15 × 6.693 × 1.535 in), mass about 4200 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1316 work?",
        "a": "The final two digits of 1316 are bore code 16, multiplied by 5 to give 80 mm."
      },
      {
        "q": "What is the speed rating of 1316-K?",
        "a": "SKF lists a 7500 r/min thermal reference speed and a 5300 r/min mechanical limiting speed for 1316 K; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1316-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1316-K allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1316",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1316-K",
      "1316 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2316-K",
    "brand": "SKF",
    "manufacturer_designation": "2316 K",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 58,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 135,
    "static_load_kN": 49,
    "fatigue_load_limit_kN": 2.24,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 6100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2316 carries code 16 = 80 mm (code × 5). Envelope 80×170×58 mm (3.15×6.693×2.283 in) with a 45.0 mm radial section height, C 135 kN, C0 49 kN and Pu 2.24 kN. The open 2316 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 7000 r/min, limiting speed 5300 r/min, catalogue mass 6100 g.",
    "applications": [
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 2316-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Assign interference to the rotating ring: on a 80 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The K suffix means a 1:12 tapered bore: 2316-K is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The  suffix on 2316-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 80 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2316-K (C 135 kN, C0 49 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2316-K?",
        "a": "SKF 2316 K measures 80 mm bore × 170 mm OD × 58 mm width (3.15 × 6.693 × 2.283 in), mass about 6100 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2316 work?",
        "a": "The final two digits of 2316 are bore code 16, multiplied by 5 to give 80 mm."
      },
      {
        "q": "How much misalignment can 2316-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2316-K allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2316-K take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2316",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2316-K",
      "2316 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1217-K",
    "brand": "SKF",
    "manufacturer_designation": "1217 K",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 48.8,
    "static_load_kN": 20.8,
    "fatigue_load_limit_kN": 0.98,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 2050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1217 carries code 17 = 85 mm (code × 5). Envelope 85×150×28 mm (3.346×5.906×1.102 in) with a 32.5 mm radial section height, C 48.8 kN, C0 20.8 kN and Pu 0.98 kN. The open 1217 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 9000 r/min, limiting speed 5600 r/min, catalogue mass 2050 g.",
    "applications": [
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1217-K (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1217-K (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "On a sleeve-mounted 1217-K, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The  suffix on 1217-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5600 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.98 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 85 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1217-K?",
        "a": "SKF 1217 K measures 85 mm bore × 150 mm OD × 28 mm width (3.346 × 5.906 × 1.102 in), mass about 2050 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1217 work?",
        "a": "The final two digits of 1217 are bore code 17, multiplied by 5 to give 85 mm."
      },
      {
        "q": "What is the speed rating of 1217-K?",
        "a": "SKF lists a 9000 r/min thermal reference speed and a 5600 r/min mechanical limiting speed for 1217 K; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1217-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1217-K allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1217",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1217-K",
      "1217 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2217-K",
    "brand": "SKF",
    "manufacturer_designation": "2217 K",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 58.5,
    "static_load_kN": 23.6,
    "fatigue_load_limit_kN": 1.12,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 2500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2217 carries code 17 = 85 mm (code × 5). Envelope 85×150×36 mm (3.346×5.906×1.417 in) with a 32.5 mm radial section height, C 58.5 kN, C0 23.6 kN and Pu 1.12 kN. The open 2217 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 8000 r/min, limiting speed 5600 r/min, catalogue mass 2500 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2217-K chamfer so the 36 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "At 85 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "On a sleeve-mounted 2217-K, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The  suffix on 2217-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5600 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 85 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 2217-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2217-K?",
        "a": "SKF 2217 K measures 85 mm bore × 150 mm OD × 36 mm width (3.346 × 5.906 × 1.417 in), mass about 2500 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2217 work?",
        "a": "The final two digits of 2217 are bore code 17, multiplied by 5 to give 85 mm."
      },
      {
        "q": "Which fits should I use for 2217-K?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 150 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2217-K?",
        "a": "Catalogue mass is 2500 g for 2217 K; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2217",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2217-K",
      "2217 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1317-K",
    "brand": "SKF",
    "manufacturer_designation": "1317 K",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 97.5,
    "static_load_kN": 38,
    "fatigue_load_limit_kN": 1.7,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 5000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1317 carries code 17 = 85 mm (code × 5). Envelope 85×180×41 mm (3.346×7.087×1.614 in) with a 47.5 mm radial section height, C 97.5 kN, C0 38 kN and Pu 1.7 kN. The open 1317 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 7000 r/min, limiting speed 4800 r/min, catalogue mass 5000 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 1317-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "At 85 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The  suffix on 1317-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4800 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 85 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 1317-K (C 97.5 kN, C0 38 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1317-K?",
        "a": "SKF 1317 K measures 85 mm bore × 180 mm OD × 41 mm width (3.346 × 7.087 × 1.614 in), mass about 5000 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1317 work?",
        "a": "The final two digits of 1317 are bore code 17, multiplied by 5 to give 85 mm."
      },
      {
        "q": "What load can 1317-K take?",
        "a": "Catalogue values for 1317 K: dynamic C 97.5 kN, static C0 38 kN, fatigue limit Pu 1.7 kN. Use C in life calculation and C0 for static checks at 85 mm bore."
      },
      {
        "q": "What is the speed rating of 1317-K?",
        "a": "SKF lists a 7000 r/min thermal reference speed and a 4800 r/min mechanical limiting speed for 1317 K; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1317",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1317-K",
      "1317 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2317-M",
    "brand": "SKF",
    "manufacturer_designation": "2317 M",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 60,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 140,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 2.28,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 7050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2317 carries code 17 = 85 mm (code × 5). Envelope 85×180×60 mm (3.346×7.087×2.362 in) with a 47.5 mm radial section height, C 140 kN, C0 51 kN and Pu 2.28 kN. The open 2317 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution. The bore is cylindrical (straight), for a press-fit on a 85 mm shaft. Reference (thermal) speed 6700 r/min, limiting speed 4800 r/min, catalogue mass 7050 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2317-M tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The spherical outer raceway lets 2317-M tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The M suffix on 2317-M denotes a machined brass cage: the choice for high speeds, marginal lubrication and shock/vibration duty, and temperature-tolerant where polymer cages are not.",
      "Assign interference to the rotating ring: on a 85 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2317-M (C 140 kN, C0 51 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 2317-M by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2317-M?",
        "a": "SKF 2317 M measures 85 mm bore × 180 mm OD × 60 mm width (3.346 × 7.087 × 2.362 in), mass about 7050 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2317 work?",
        "a": "The final two digits of 2317 are bore code 17, multiplied by 5 to give 85 mm."
      },
      {
        "q": "What is the speed rating of 2317-M?",
        "a": "SKF lists a 6700 r/min thermal reference speed and a 4800 r/min mechanical limiting speed for 2317 M; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 2317-M tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2317-M allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2317",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2317-KM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×60 mm envelope with catalogue ratings within 10 %; 2317 KM is the machined brass cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2317-M",
      "2317 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2317-KM",
    "brand": "SKF",
    "manufacturer_designation": "2317 KM",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 60,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 140,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 2.28,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 7050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2317 carries code 17 = 85 mm (code × 5). Envelope 85×180×60 mm (3.346×7.087×2.362 in) with a 47.5 mm radial section height, C 140 kN, C0 51 kN and Pu 2.28 kN. The open 2317 KM carries no shields or seals and relies on application lubrication and external sealing. The KM suffix identifies the machined brass cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 6700 r/min, limiting speed 4800 r/min, catalogue mass 7050 g.",
    "applications": [
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 2317-KM by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Mount 2317-KM by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The K suffix means a 1:12 tapered bore: 2317-KM is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The KM suffix on 2317-KM denotes a machined brass cage: the choice for high speeds, marginal lubrication and shock/vibration duty, and temperature-tolerant where polymer cages are not.",
      "Fillet radii must clear the 2317-KM chamfer so the 60 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2317-KM (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2317-KM?",
        "a": "SKF 2317 KM measures 85 mm bore × 180 mm OD × 60 mm width (3.346 × 7.087 × 2.362 in), mass about 7050 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2317 work?",
        "a": "The final two digits of 2317 are bore code 17, multiplied by 5 to give 85 mm."
      },
      {
        "q": "How much misalignment can 2317-KM tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2317-KM allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2317-KM take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2317",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2317-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×60 mm envelope with catalogue ratings within 10 %; 2317 M is the machined brass cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2317-KM",
      "2317 KM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1218-K",
    "brand": "SKF",
    "manufacturer_designation": "1218 K",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 30,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 57.2,
    "static_load_kN": 23.6,
    "fatigue_load_limit_kN": 1.08,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 2500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1218 carries code 18 = 90 mm (code × 5). Envelope 90×160×30 mm (3.543×6.299×1.181 in) with a 35.0 mm radial section height, C 57.2 kN, C0 23.6 kN and Pu 1.08 kN. The open 1218 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 8500 r/min, limiting speed 5300 r/min, catalogue mass 2500 g.",
    "applications": [
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 90 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Mount 1218-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The K suffix means a 1:12 tapered bore: 1218-K is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The  suffix on 1218-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 1218-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 1.08 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1218-K?",
        "a": "SKF 1218 K measures 90 mm bore × 160 mm OD × 30 mm width (3.543 × 6.299 × 1.181 in), mass about 2500 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1218 work?",
        "a": "The final two digits of 1218 are bore code 18, multiplied by 5 to give 90 mm."
      },
      {
        "q": "How much misalignment can 1218-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1218-K allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 1218-K take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1218",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1218-K",
      "1218 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2218-K",
    "brand": "SKF",
    "manufacturer_designation": "2218 K",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 70.2,
    "static_load_kN": 28.5,
    "fatigue_load_limit_kN": 1.32,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 3400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2218 carries code 18 = 90 mm (code × 5). Envelope 90×160×40 mm (3.543×6.299×1.575 in) with a 35.0 mm radial section height, C 70.2 kN, C0 28.5 kN and Pu 1.32 kN. The open 2218 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 7500 r/min, limiting speed 5300 r/min, catalogue mass 3400 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2218-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The spherical outer raceway lets 2218-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The K suffix means a 1:12 tapered bore: 2218-K is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The  suffix on 2218-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 2218-K (C 70.2 kN, C0 28.5 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 2218-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2218-K?",
        "a": "SKF 2218 K measures 90 mm bore × 160 mm OD × 40 mm width (3.543 × 6.299 × 1.575 in), mass about 3400 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2218 work?",
        "a": "The final two digits of 2218 are bore code 18, multiplied by 5 to give 90 mm."
      },
      {
        "q": "How heavy is 2218-K?",
        "a": "Catalogue mass is 3400 g for 2218 K; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2218-K take?",
        "a": "Catalogue values for 2218 K: dynamic C 70.2 kN, static C0 28.5 kN, fatigue limit Pu 1.32 kN. Use C in life calculation and C0 for static checks at 90 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2218",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2218-K",
      "2218 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1318-K",
    "brand": "SKF",
    "manufacturer_designation": "1318 K",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 117,
    "static_load_kN": 44,
    "fatigue_load_limit_kN": 1.93,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 5800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1318 carries code 18 = 90 mm (code × 5). Envelope 90×190×43 mm (3.543×7.48×1.693 in) with a 50.0 mm radial section height, C 117 kN, C0 44 kN and Pu 1.93 kN. The open 1318 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 6700 r/min, limiting speed 4500 r/min, catalogue mass 5800 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 1318-K (C 117 kN, C0 44 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The spherical outer raceway lets 1318-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The K suffix means a 1:12 tapered bore: 1318-K is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The  suffix on 1318-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 1318-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 1318-K chamfer so the 43 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1318-K?",
        "a": "SKF 1318 K measures 90 mm bore × 190 mm OD × 43 mm width (3.543 × 7.48 × 1.693 in), mass about 5800 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1318 work?",
        "a": "The final two digits of 1318 are bore code 18, multiplied by 5 to give 90 mm."
      },
      {
        "q": "How heavy is 1318-K?",
        "a": "Catalogue mass is 5800 g for 1318 K; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 1318-K take?",
        "a": "Catalogue values for 1318 K: dynamic C 117 kN, static C0 44 kN, fatigue limit Pu 1.93 kN. Use C in life calculation and C0 for static checks at 90 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1318",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1318-K",
      "1318 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2318-K",
    "brand": "SKF",
    "manufacturer_designation": "2318 K",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 64,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 151,
    "static_load_kN": 57,
    "fatigue_load_limit_kN": 2.5,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 8450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2318 carries code 18 = 90 mm (code × 5). Envelope 90×190×64 mm (3.543×7.48×2.52 in) with a 50.0 mm radial section height, C 151 kN, C0 57 kN and Pu 2.5 kN. The open 2318 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 6300 r/min, limiting speed 4500 r/min, catalogue mass 8450 g.",
    "applications": [
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 90 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Mount 2318-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The  suffix on 2318-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2318-K chamfer so the 64 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2318-K (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2318-K?",
        "a": "SKF 2318 K measures 90 mm bore × 190 mm OD × 64 mm width (3.543 × 7.48 × 2.52 in), mass about 8450 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2318 work?",
        "a": "The final two digits of 2318 are bore code 18, multiplied by 5 to give 90 mm."
      },
      {
        "q": "What load can 2318-K take?",
        "a": "Catalogue values for 2318 K: dynamic C 151 kN, static C0 57 kN, fatigue limit Pu 2.5 kN. Use C in life calculation and C0 for static checks at 90 mm bore."
      },
      {
        "q": "What is the speed rating of 2318-K?",
        "a": "SKF lists a 6300 r/min thermal reference speed and a 4500 r/min mechanical limiting speed for 2318 K; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2318",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2318-K",
      "2318 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1219-K",
    "brand": "SKF",
    "manufacturer_designation": "1219 K",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 63.7,
    "static_load_kN": 27,
    "fatigue_load_limit_kN": 1.2,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 3100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1219 carries code 19 = 95 mm (code × 5). Envelope 95×170×32 mm (3.74×6.693×1.26 in) with a 37.5 mm radial section height, C 63.7 kN, C0 27 kN and Pu 1.2 kN. The open 1219 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 8000 r/min, limiting speed 5000 r/min, catalogue mass 3100 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 1219-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Catalogue ratings for 1219-K (C 63.7 kN, C0 27 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "On a sleeve-mounted 1219-K, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The  suffix on 1219-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 1219-K (C 63.7 kN, C0 27 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1219-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1219-K?",
        "a": "SKF 1219 K measures 95 mm bore × 170 mm OD × 32 mm width (3.74 × 6.693 × 1.26 in), mass about 3100 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1219 work?",
        "a": "The final two digits of 1219 are bore code 19, multiplied by 5 to give 95 mm."
      },
      {
        "q": "What is the speed rating of 1219-K?",
        "a": "SKF lists a 8000 r/min thermal reference speed and a 5000 r/min mechanical limiting speed for 1219 K; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1219-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1219-K allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1219",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1219-K",
      "1219 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2219-K",
    "brand": "SKF",
    "manufacturer_designation": "2219 K",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 83.2,
    "static_load_kN": 34.5,
    "fatigue_load_limit_kN": 1.53,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 4100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2219 carries code 19 = 95 mm (code × 5). Envelope 95×170×43 mm (3.74×6.693×1.693 in) with a 37.5 mm radial section height, C 83.2 kN, C0 34.5 kN and Pu 1.53 kN. The open 2219 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 7000 r/min, limiting speed 5000 r/min, catalogue mass 4100 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 95 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Fillet radii must clear the 2219-K chamfer so the 43 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The K suffix means a 1:12 tapered bore: 2219-K is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The  suffix on 2219-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 2219-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 1.53 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2219-K?",
        "a": "SKF 2219 K measures 95 mm bore × 170 mm OD × 43 mm width (3.74 × 6.693 × 1.693 in), mass about 4100 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2219 work?",
        "a": "The final two digits of 2219 are bore code 19, multiplied by 5 to give 95 mm."
      },
      {
        "q": "How much misalignment can 2219-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2219-K allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2219-K take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2219",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2219-K",
      "2219 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1319-K",
    "brand": "SKF",
    "manufacturer_designation": "1319 K",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 133,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 2.16,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 6700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1319 carries code 19 = 95 mm (code × 5). Envelope 95×200×45 mm (3.74×7.874×1.772 in) with a 52.5 mm radial section height, C 133 kN, C0 51 kN and Pu 2.16 kN. The open 1319 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 6300 r/min, limiting speed 4300 r/min, catalogue mass 6700 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 95 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the 1319-K chamfer so the 45 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "On a sleeve-mounted 1319-K, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The  suffix on 1319-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 1319-K chamfer so the 45 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1319-K (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1319-K?",
        "a": "SKF 1319 K measures 95 mm bore × 200 mm OD × 45 mm width (3.74 × 7.874 × 1.772 in), mass about 6700 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1319 work?",
        "a": "The final two digits of 1319 are bore code 19, multiplied by 5 to give 95 mm."
      },
      {
        "q": "Which fits should I use for 1319-K?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 200 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 1319-K?",
        "a": "Catalogue mass is 6700 g for 1319 K; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1319",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1319-K",
      "1319 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2319-M",
    "brand": "SKF",
    "manufacturer_designation": "2319 M",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 67,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 165,
    "static_load_kN": 64,
    "fatigue_load_limit_kN": 2.75,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 9800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2319 carries code 19 = 95 mm (code × 5). Envelope 95×200×67 mm (3.74×7.874×2.638 in) with a 52.5 mm radial section height, C 165 kN, C0 64 kN and Pu 2.75 kN. The open 2319 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution. The bore is cylindrical (straight), for a press-fit on a 95 mm shaft. Reference (thermal) speed 6000 r/min, limiting speed 4500 r/min, catalogue mass 9800 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2319-M (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The fatigue load limit is 2.75 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The M suffix on 2319-M denotes a machined brass cage: the choice for high speeds, marginal lubrication and shock/vibration duty, and temperature-tolerant where polymer cages are not.",
      "Mount 2319-M by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 2.75 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 95 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2319-M?",
        "a": "SKF 2319 M measures 95 mm bore × 200 mm OD × 67 mm width (3.74 × 7.874 × 2.638 in), mass about 9800 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2319 work?",
        "a": "The final two digits of 2319 are bore code 19, multiplied by 5 to give 95 mm."
      },
      {
        "q": "Can 2319-M take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 2319-M?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 200 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2319",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2319-KM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×67 mm envelope with catalogue ratings within 10 %; 2319 KM is the machined brass cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2319-M",
      "2319 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2319-KM",
    "brand": "SKF",
    "manufacturer_designation": "2319 KM",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 67,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 165,
    "static_load_kN": 64,
    "fatigue_load_limit_kN": 2.75,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 9800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2319 carries code 19 = 95 mm (code × 5). Envelope 95×200×67 mm (3.74×7.874×2.638 in) with a 52.5 mm radial section height, C 165 kN, C0 64 kN and Pu 2.75 kN. The open 2319 KM carries no shields or seals and relies on application lubrication and external sealing. The KM suffix identifies the machined brass cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 6000 r/min, limiting speed 4500 r/min, catalogue mass 9800 g.",
    "applications": [
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 95 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Assign interference to the rotating ring: on a 95 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The KM suffix on 2319-KM denotes a machined brass cage: the choice for high speeds, marginal lubrication and shock/vibration duty, and temperature-tolerant where polymer cages are not.",
      "Assign interference to the rotating ring: on a 95 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 2319-KM (C 165 kN, C0 64 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2319-KM?",
        "a": "SKF 2319 KM measures 95 mm bore × 200 mm OD × 67 mm width (3.74 × 7.874 × 2.638 in), mass about 9800 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2319 work?",
        "a": "The final two digits of 2319 are bore code 19, multiplied by 5 to give 95 mm."
      },
      {
        "q": "What load can 2319-KM take?",
        "a": "Catalogue values for 2319 KM: dynamic C 165 kN, static C0 64 kN, fatigue limit Pu 2.75 kN. Use C in life calculation and C0 for static checks at 95 mm bore."
      },
      {
        "q": "What is the speed rating of 2319-KM?",
        "a": "SKF lists a 6000 r/min thermal reference speed and a 4500 r/min mechanical limiting speed for 2319 KM; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2319",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "2319-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×67 mm envelope with catalogue ratings within 10 %; 2319 M is the machined brass cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2319-KM",
      "2319 KM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1220-K",
    "brand": "SKF",
    "manufacturer_designation": "1220 K",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 68.9,
    "static_load_kN": 30,
    "fatigue_load_limit_kN": 1.29,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 3700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1220 carries code 20 = 100 mm (code × 5). Envelope 100×180×34 mm (3.937×7.087×1.339 in) with a 40.0 mm radial section height, C 68.9 kN, C0 30 kN and Pu 1.29 kN. The open 1220 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 7500 r/min, limiting speed 4800 r/min, catalogue mass 3700 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 1220-K (C 68.9 kN, C0 30 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Catalogue ratings for 1220-K (C 68.9 kN, C0 30 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "On a sleeve-mounted 1220-K, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The  suffix on 1220-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4800 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 1220-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 1220-K chamfer so the 34 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1220-K?",
        "a": "SKF 1220 K measures 100 mm bore × 180 mm OD × 34 mm width (3.937 × 7.087 × 1.339 in), mass about 3700 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1220 work?",
        "a": "The final two digits of 1220 are bore code 20, multiplied by 5 to give 100 mm."
      },
      {
        "q": "What is the speed rating of 1220-K?",
        "a": "SKF lists a 7500 r/min thermal reference speed and a 4800 r/min mechanical limiting speed for 1220 K; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1220-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1220-K allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1220",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1220-K",
      "1220 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2220-K",
    "brand": "SKF",
    "manufacturer_designation": "2220 K",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 97.5,
    "static_load_kN": 40.5,
    "fatigue_load_limit_kN": 1.76,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 5000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2220 carries code 20 = 100 mm (code × 5). Envelope 100×180×46 mm (3.937×7.087×1.811 in) with a 40.0 mm radial section height, C 97.5 kN, C0 40.5 kN and Pu 1.76 kN. The open 2220 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 6700 r/min, limiting speed 4800 r/min, catalogue mass 5000 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 100 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the 2220-K chamfer so the 46 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "On a sleeve-mounted 2220-K, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The  suffix on 2220-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4800 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 2220-K chamfer so the 46 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2220-K (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2220-K?",
        "a": "SKF 2220 K measures 100 mm bore × 180 mm OD × 46 mm width (3.937 × 7.087 × 1.811 in), mass about 5000 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2220 work?",
        "a": "The final two digits of 2220 are bore code 20, multiplied by 5 to give 100 mm."
      },
      {
        "q": "Which fits should I use for 2220-K?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 180 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 2220-K?",
        "a": "Catalogue mass is 5000 g for 2220 K; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2220",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2220-K",
      "2220 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1320-K",
    "brand": "SKF",
    "manufacturer_designation": "1320 K",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 143,
    "static_load_kN": 57,
    "fatigue_load_limit_kN": 2.36,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 8300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1320 carries code 20 = 100 mm (code × 5). Envelope 100×215×47 mm (3.937×8.465×1.85 in) with a 57.5 mm radial section height, C 143 kN, C0 57 kN and Pu 2.36 kN. The open 1320 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 6000 r/min, limiting speed 4000 r/min, catalogue mass 8300 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 100 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Fillet radii must clear the 1320-K chamfer so the 47 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The  suffix on 1320-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 1320-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 2.36 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1320-K?",
        "a": "SKF 1320 K measures 100 mm bore × 215 mm OD × 47 mm width (3.937 × 8.465 × 1.85 in), mass about 8300 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1320 work?",
        "a": "The final two digits of 1320 are bore code 20, multiplied by 5 to give 100 mm."
      },
      {
        "q": "What load can 1320-K take?",
        "a": "Catalogue values for 1320 K: dynamic C 143 kN, static C0 57 kN, fatigue limit Pu 2.36 kN. Use C in life calculation and C0 for static checks at 100 mm bore."
      },
      {
        "q": "What is the speed rating of 1320-K?",
        "a": "SKF lists a 6000 r/min thermal reference speed and a 4000 r/min mechanical limiting speed for 1320 K; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1320",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1320-K",
      "1320 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2320-K",
    "brand": "SKF",
    "manufacturer_designation": "2320 K",
    "series": "2300-series",
    "type": "self_aligning_ball",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 73,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 190,
    "static_load_kN": 80,
    "fatigue_load_limit_kN": 3.25,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 12500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 23xx series is the wide medium-section self-aligning ball bearing (ISO dimension series 23). the last two digits encode the bore: 2320 carries code 20 = 100 mm (code × 5). Envelope 100×215×73 mm (3.937×8.465×2.874 in) with a 57.5 mm radial section height, C 190 kN, C0 80 kN and Pu 3.25 kN. The open 2320 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 5600 r/min, limiting speed 4000 r/min, catalogue mass 12500 g.",
    "applications": [
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts",
      "agricultural gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 2320-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Catalogue ratings for 2320-K (C 190 kN, C0 80 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The K suffix means a 1:12 tapered bore: 2320-K is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The  suffix on 2320-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 2320-K (C 190 kN, C0 80 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 2320-K by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2320-K?",
        "a": "SKF 2320 K measures 100 mm bore × 215 mm OD × 73 mm width (3.937 × 8.465 × 2.874 in), mass about 12500 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2320 work?",
        "a": "The final two digits of 2320 are bore code 20, multiplied by 5 to give 100 mm."
      },
      {
        "q": "How heavy is 2320-K?",
        "a": "Catalogue mass is 12500 g for 2320 K; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 2320-K take?",
        "a": "Catalogue values for 2320 K: dynamic C 190 kN, static C0 80 kN, fatigue limit Pu 3.25 kN. Use C in life calculation and C0 for static checks at 100 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2320",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2320-K",
      "2320 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1222-K",
    "brand": "SKF",
    "manufacturer_designation": "1222 K",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 88.4,
    "static_load_kN": 39,
    "fatigue_load_limit_kN": 1.6,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 5150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1222 carries code 22 = 110 mm (code × 5). Envelope 110×200×38 mm (4.331×7.874×1.496 in) with a 45.0 mm radial section height, C 88.4 kN, C0 39 kN and Pu 1.6 kN. The open 1222 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 6700 r/min, limiting speed 4300 r/min, catalogue mass 5150 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1222-K (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The fatigue load limit is 1.6 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "On a sleeve-mounted 1222-K, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The  suffix on 1222-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 1.6 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 110 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1222-K?",
        "a": "SKF 1222 K measures 110 mm bore × 200 mm OD × 38 mm width (4.331 × 7.874 × 1.496 in), mass about 5150 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1222 work?",
        "a": "The final two digits of 1222 are bore code 22, multiplied by 5 to give 110 mm."
      },
      {
        "q": "What is the speed rating of 1222-K?",
        "a": "SKF lists a 6700 r/min thermal reference speed and a 4300 r/min mechanical limiting speed for 1222 K; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1222-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1222-K allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1222",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1222-K",
      "1222 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "2222-K",
    "brand": "SKF",
    "manufacturer_designation": "2222 K",
    "series": "2200-series",
    "type": "self_aligning_ball",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 53,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 124,
    "static_load_kN": 52,
    "fatigue_load_limit_kN": 2.12,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 7100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2222 carries code 22 = 110 mm (code × 5). Envelope 110×200×53 mm (4.331×7.874×2.087 in) with a 45.0 mm radial section height, C 124 kN, C0 52 kN and Pu 2.12 kN. The open 2222 K carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 6000 r/min, limiting speed 4300 r/min, catalogue mass 7100 g.",
    "applications": [
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "false brinelling from vibration while the shaft stands idle",
      "fretting corrosion on a creeping shaft or housing seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the 2222-K chamfer so the 53 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring: on a 110 mm rotating shaft use a m6 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The K suffix means a 1:12 tapered bore: 2222-K is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.",
      "The  suffix on 2222-K denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 110 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 2222-K tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 2222-K?",
        "a": "SKF 2222 K measures 110 mm bore × 200 mm OD × 53 mm width (4.331 × 7.874 × 2.087 in), mass about 7100 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 2222 work?",
        "a": "The final two digits of 2222 are bore code 22, multiplied by 5 to give 110 mm."
      },
      {
        "q": "How much misalignment can 2222-K tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2222-K allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 2222-K take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "2222",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "2222-K",
      "2222 K"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1322-M",
    "brand": "SKF",
    "manufacturer_designation": "1322 M",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 163,
    "static_load_kN": 72,
    "fatigue_load_limit_kN": 2.75,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 12000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1322 carries code 22 = 110 mm (code × 5). Envelope 110×240×50 mm (4.331×9.449×1.969 in) with a 65.0 mm radial section height, C 163 kN, C0 72 kN and Pu 2.75 kN. The open 1322 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution. The bore is cylindrical (straight), for a press-fit on a 110 mm shaft. Reference (thermal) speed 5300 r/min, limiting speed 3600 r/min, catalogue mass 12000 g.",
    "applications": [
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment",
      "material-handling equipment"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 110 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Fillet radii must clear the 1322-M chamfer so the 50 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The M suffix on 1322-M denotes a machined brass cage: the choice for high speeds, marginal lubrication and shock/vibration duty, and temperature-tolerant where polymer cages are not.",
      "Catalogue ratings for 1322-M (C 163 kN, C0 72 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1322-M by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 2.75 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1322-M?",
        "a": "SKF 1322 M measures 110 mm bore × 240 mm OD × 50 mm width (4.331 × 9.449 × 1.969 in), mass about 12000 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1322 work?",
        "a": "The final two digits of 1322 are bore code 22, multiplied by 5 to give 110 mm."
      },
      {
        "q": "What load can 1322-M take?",
        "a": "Catalogue values for 1322 M: dynamic C 163 kN, static C0 72 kN, fatigue limit Pu 2.75 kN. Use C in life calculation and C0 for static checks at 110 mm bore."
      },
      {
        "q": "What is the speed rating of 1322-M?",
        "a": "SKF lists a 5300 r/min thermal reference speed and a 3600 r/min mechanical limiting speed for 1322 M; real limits also depend on lubrication and fits."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1322",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1322-KM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 1322 KM is the machined brass cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1322-M",
      "1322 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1322-KM",
    "brand": "SKF",
    "manufacturer_designation": "1322 KM",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 163,
    "static_load_kN": 72,
    "fatigue_load_limit_kN": 2.75,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 12000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 1322 carries code 22 = 110 mm (code × 5). Envelope 110×240×50 mm (4.331×9.449×1.969 in) with a 65.0 mm radial section height, C 163 kN, C0 72 kN and Pu 2.75 kN. The open 1322 KM carries no shields or seals and relies on application lubrication and external sealing. The KM suffix identifies the machined brass cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 5300 r/min, limiting speed 3600 r/min, catalogue mass 12000 g.",
    "applications": [
      "conveyor drum and pulley shafts",
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 1322-KM (C 163 kN, C0 72 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The fatigue load limit is 2.75 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The KM suffix on 1322-KM denotes a machined brass cage: the choice for high speeds, marginal lubrication and shock/vibration duty, and temperature-tolerant where polymer cages are not.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1322-KM (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 110 mm rotating shaft use a m6 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1322-KM?",
        "a": "SKF 1322 KM measures 110 mm bore × 240 mm OD × 50 mm width (4.331 × 9.449 × 1.969 in), mass about 12000 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1322 work?",
        "a": "The final two digits of 1322 are bore code 22, multiplied by 5 to give 110 mm."
      },
      {
        "q": "Can 1322-KM take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 1322-KM?",
        "a": "With a rotating inner ring use roughly m6 on the shaft and H7 in the 240 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1322",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "1322-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 1322 M is the machined brass cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1322-KM",
      "1322 KM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1224-M",
    "brand": "SKF",
    "manufacturer_designation": "1224 M",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 120,
    "D_mm": 215,
    "B_mm": 42,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 119,
    "static_load_kN": 53,
    "fatigue_load_limit_kN": 2.12,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 6750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1224 carries code 24 = 120 mm (code × 5). Envelope 120×215×42 mm (4.724×8.465×1.654 in) with a 47.5 mm radial section height, C 119 kN, C0 53 kN and Pu 2.12 kN. The open 1224 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution. The bore is cylindrical (straight), for a press-fit on a 120 mm shaft. Reference (thermal) speed 6300 r/min, limiting speed 4000 r/min, catalogue mass 6750 g.",
    "applications": [
      "crusher feeders",
      "large industrial gearboxes",
      "material-handling winches",
      "large conveyor drives"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 2.12 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1224-M (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The M suffix on 1224-M denotes a machined brass cage: the choice for high speeds, marginal lubrication and shock/vibration duty, and temperature-tolerant where polymer cages are not.",
      "Fillet radii must clear the 1224-M chamfer so the 42 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1224-M (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 120 mm rotating shaft use a m6 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1224-M?",
        "a": "SKF 1224 M measures 120 mm bore × 215 mm OD × 42 mm width (4.724 × 8.465 × 1.654 in), mass about 6750 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1224 work?",
        "a": "The final two digits of 1224 are bore code 24, multiplied by 5 to give 120 mm."
      },
      {
        "q": "What is the speed rating of 1224-M?",
        "a": "SKF lists a 6300 r/min thermal reference speed and a 4000 r/min mechanical limiting speed for 1224 M; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 1224-M tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1224-M allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1224-KM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 120×215×42 mm envelope with catalogue ratings within 10 %; 1224 KM is the machined brass cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1224-M",
      "1224 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1224-KM",
    "brand": "SKF",
    "manufacturer_designation": "1224 KM",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 120,
    "D_mm": 215,
    "B_mm": 42,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 119,
    "static_load_kN": 53,
    "fatigue_load_limit_kN": 2.12,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 6750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1224 carries code 24 = 120 mm (code × 5). Envelope 120×215×42 mm (4.724×8.465×1.654 in) with a 47.5 mm radial section height, C 119 kN, C0 53 kN and Pu 2.12 kN. The open 1224 KM carries no shields or seals and relies on application lubrication and external sealing. The KM suffix identifies the machined brass cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 6300 r/min, limiting speed 4000 r/min, catalogue mass 6750 g.",
    "applications": [
      "mill and kiln auxiliary drives",
      "paper-machine rolls",
      "marine deck machinery",
      "crusher feeders"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 120 mm rotating shaft use a m6 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "At 120 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "On a sleeve-mounted 1224-KM, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The KM suffix on 1224-KM denotes a machined brass cage: the choice for high speeds, marginal lubrication and shock/vibration duty, and temperature-tolerant where polymer cages are not.",
      "At 120 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 1224-KM tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1224-KM?",
        "a": "SKF 1224 KM measures 120 mm bore × 215 mm OD × 42 mm width (4.724 × 8.465 × 1.654 in), mass about 6750 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1224 work?",
        "a": "The final two digits of 1224 are bore code 24, multiplied by 5 to give 120 mm."
      },
      {
        "q": "Which fits should I use for 1224-KM?",
        "a": "With a rotating inner ring use roughly m6 on the shaft and H7 in the 215 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 1224-KM?",
        "a": "Catalogue mass is 6750 g for 1224 KM; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1224-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 120×215×42 mm envelope with catalogue ratings within 10 %; 1224 M is the machined brass cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1224-KM",
      "1224 KM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1226-M",
    "brand": "SKF",
    "manufacturer_designation": "1226 M",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 130,
    "D_mm": 230,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 127,
    "static_load_kN": 58.5,
    "fatigue_load_limit_kN": 2.24,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 8300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1226 carries code 26 = 130 mm (code × 5). Envelope 130×230×46 mm (5.118×9.055×1.811 in) with a 50.0 mm radial section height, C 127 kN, C0 58.5 kN and Pu 2.24 kN. The open 1226 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution. The bore is cylindrical (straight), for a press-fit on a 130 mm shaft. Reference (thermal) speed 5600 r/min, limiting speed 3600 r/min, catalogue mass 8300 g.",
    "applications": [
      "paper-machine rolls",
      "marine deck machinery",
      "crusher feeders",
      "large industrial gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 1226-M tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The spherical outer raceway lets 1226-M tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The M suffix on 1226-M denotes a machined brass cage: the choice for high speeds, marginal lubrication and shock/vibration duty, and temperature-tolerant where polymer cages are not.",
      "Assign interference to the rotating ring: on a 130 mm rotating shaft use a m6 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 1226-M (C 127 kN, C0 58.5 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 1226-M by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1226-M?",
        "a": "SKF 1226 M measures 130 mm bore × 230 mm OD × 46 mm width (5.118 × 9.055 × 1.811 in), mass about 8300 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1226 work?",
        "a": "The final two digits of 1226 are bore code 26, multiplied by 5 to give 130 mm."
      },
      {
        "q": "How heavy is 1226-M?",
        "a": "Catalogue mass is 8300 g for 1226 M; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 1226-M take?",
        "a": "Catalogue values for 1226 M: dynamic C 127 kN, static C0 58.5 kN, fatigue limit Pu 2.24 kN. Use C in life calculation and C0 for static checks at 130 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1226-KM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 130×230×46 mm envelope with catalogue ratings within 10 %; 1226 KM is the machined brass cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1226-M",
      "1226 M"
    ],
    "locale_variants": {}
  },
  {
    "sku": "1226-KM",
    "brand": "SKF",
    "manufacturer_designation": "1226 KM",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 130,
    "D_mm": 230,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 127,
    "static_load_kN": 58.5,
    "fatigue_load_limit_kN": 2.24,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 8300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1226 carries code 26 = 130 mm (code × 5). Envelope 130×230×46 mm (5.118×9.055×1.811 in) with a 50.0 mm radial section height, C 127 kN, C0 58.5 kN and Pu 2.24 kN. The open 1226 KM carries no shields or seals and relies on application lubrication and external sealing. The KM suffix identifies the machined brass cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 5600 r/min, limiting speed 3600 r/min, catalogue mass 8300 g.",
    "applications": [
      "large conveyor drives",
      "heavy fan and blower shafts",
      "mill and kiln auxiliary drives",
      "paper-machine rolls"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 1226-KM by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Mount 1226-KM by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "On a sleeve-mounted 1226-KM, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.",
      "The KM suffix on 1226-KM denotes a machined brass cage: the choice for high speeds, marginal lubrication and shock/vibration duty, and temperature-tolerant where polymer cages are not.",
      "Fillet radii must clear the 1226-KM chamfer so the 46 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1226-KM (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 1226-KM?",
        "a": "SKF 1226 KM measures 130 mm bore × 230 mm OD × 46 mm width (5.118 × 9.055 × 1.811 in), mass about 8300 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 1226 work?",
        "a": "The final two digits of 1226 are bore code 26, multiplied by 5 to give 130 mm."
      },
      {
        "q": "Which fits should I use for 1226-KM?",
        "a": "With a rotating inner ring use roughly m6 on the shaft and H7 in the 230 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 1226-KM?",
        "a": "Catalogue mass is 8300 g for 1226 KM; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1226-M",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 130×230×46 mm envelope with catalogue ratings within 10 %; 1226 M is the machined brass cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "1226-KM",
      "1226 KM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "13030",
    "brand": "SKF",
    "manufacturer_designation": "13030",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 150,
    "D_mm": 225,
    "B_mm": 56,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 57.2,
    "static_load_kN": 23.6,
    "fatigue_load_limit_kN": 0.88,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 7500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 13030 carries code 30 = 150 mm (code × 5). Envelope 150×225×56 mm (5.906×8.858×2.205 in) with a 37.5 mm radial section height, C 57.2 kN, C0 23.6 kN and Pu 0.88 kN. The open 13030 carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 150 mm shaft. Reference (thermal) speed 5600 r/min, limiting speed 3400 r/min, catalogue mass 7500 g.",
    "applications": [
      "crusher feeders",
      "large industrial gearboxes",
      "material-handling winches",
      "large conveyor drives"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 13030 (C 57.2 kN, C0 23.6 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 13030 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The  suffix on 13030 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 3400 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 13030 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.88 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 150 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 13030?",
        "a": "SKF 13030 measures 150 mm bore × 225 mm OD × 56 mm width (5.906 × 8.858 × 2.205 in), mass about 7500 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 13030 work?",
        "a": "The final two digits of 13030 are bore code 30, multiplied by 5 to give 150 mm."
      },
      {
        "q": "How heavy is 13030?",
        "a": "Catalogue mass is 7500 g for 13030; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can 13030 take?",
        "a": "Catalogue values for 13030: dynamic C 57.2 kN, static C0 23.6 kN, fatigue limit Pu 0.88 kN. Use C in life calculation and C0 for static checks at 150 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "13030",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "13030",
      "13030"
    ],
    "locale_variants": {}
  },
  {
    "sku": "13036",
    "brand": "SKF",
    "manufacturer_designation": "13036",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 180,
    "D_mm": 280,
    "B_mm": 74,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 95.6,
    "static_load_kN": 40,
    "fatigue_load_limit_kN": 1.34,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 16000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 13036 carries code 36 = 180 mm (code × 5). Envelope 180×280×74 mm (7.087×11.024×2.913 in) with a 50.0 mm radial section height, C 95.6 kN, C0 40 kN and Pu 1.34 kN. The open 13036 carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 180 mm shaft. Reference (thermal) speed 4500 r/min, limiting speed 2800 r/min, catalogue mass 16000 g.",
    "applications": [
      "paper-machine rolls",
      "marine deck machinery",
      "crusher feeders",
      "large industrial gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 13036 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The spherical outer raceway lets 13036 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The  suffix on 13036 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 2800 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 180 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets 13036 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 13036 chamfer so the 74 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 13036?",
        "a": "SKF 13036 measures 180 mm bore × 280 mm OD × 74 mm width (7.087 × 11.024 × 2.913 in), mass about 16000 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 13036 work?",
        "a": "The final two digits of 13036 are bore code 36, multiplied by 5 to give 180 mm."
      },
      {
        "q": "What is the speed rating of 13036?",
        "a": "SKF lists a 4500 r/min thermal reference speed and a 2800 r/min mechanical limiting speed for 13036; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 13036 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 13036 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "13036",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "13036",
      "13036"
    ],
    "locale_variants": {}
  },
  {
    "sku": "13940",
    "brand": "SKF",
    "manufacturer_designation": "13940",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 200,
    "D_mm": 280,
    "B_mm": 60,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 60.5,
    "static_load_kN": 29,
    "fatigue_load_limit_kN": 0.97,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 10500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 13940 carries code 40 = 200 mm (code × 5). Envelope 200×280×60 mm (7.874×11.024×2.362 in) with a 40.0 mm radial section height, C 60.5 kN, C0 29 kN and Pu 0.97 kN. The open 13940 carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 200 mm shaft. Reference (thermal) speed 4300 r/min, limiting speed 2600 r/min, catalogue mass 10500 g.",
    "applications": [
      "crusher feeders",
      "large industrial gearboxes",
      "material-handling winches",
      "large conveyor drives"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 13940 (C 60.5 kN, C0 29 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 13940 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The  suffix on 13940 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 2600 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 13940 chamfer so the 60 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 13940 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 200 mm rotating shaft use a m6 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 13940?",
        "a": "SKF 13940 measures 200 mm bore × 280 mm OD × 60 mm width (7.874 × 11.024 × 2.362 in), mass about 10500 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 13940 work?",
        "a": "The final two digits of 13940 are bore code 40, multiplied by 5 to give 200 mm."
      },
      {
        "q": "What is the speed rating of 13940?",
        "a": "SKF lists a 4300 r/min thermal reference speed and a 2600 r/min mechanical limiting speed for 13940; real limits also depend on lubrication and fits."
      },
      {
        "q": "How much misalignment can 13940 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 13940 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "13940",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "13940",
      "13940"
    ],
    "locale_variants": {}
  },
  {
    "sku": "13944",
    "brand": "SKF",
    "manufacturer_designation": "13944",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 220,
    "D_mm": 300,
    "B_mm": 60,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 60.5,
    "static_load_kN": 30.5,
    "fatigue_load_limit_kN": 0.97,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 11000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 13944 carries code 44 = 220 mm (code × 5). Envelope 220×300×60 mm (8.661×11.811×2.362 in) with a 40.0 mm radial section height, C 60.5 kN, C0 30.5 kN and Pu 0.97 kN. The open 13944 carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 220 mm shaft. Reference (thermal) speed 3800 r/min, limiting speed 2400 r/min, catalogue mass 11000 g.",
    "applications": [
      "heavy fan and blower shafts",
      "mill and kiln auxiliary drives",
      "paper-machine rolls",
      "marine deck machinery"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 13944 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The fatigue load limit is 0.97 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The  suffix on 13944 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 2400 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 13944 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.97 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 220 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 13944?",
        "a": "SKF 13944 measures 220 mm bore × 300 mm OD × 60 mm width (8.661 × 11.811 × 2.362 in), mass about 11000 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 13944 work?",
        "a": "The final two digits of 13944 are bore code 44, multiplied by 5 to give 220 mm."
      },
      {
        "q": "Can 13944 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 13944?",
        "a": "With a rotating inner ring use roughly m6 on the shaft and H7 in the 300 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "13944",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "13944",
      "13944"
    ],
    "locale_variants": {}
  },
  {
    "sku": "13948",
    "brand": "SKF",
    "manufacturer_designation": "13948",
    "series": "1300-series",
    "type": "self_aligning_ball",
    "d_mm": 240,
    "D_mm": 320,
    "B_mm": 60,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 60.5,
    "static_load_kN": 32,
    "fatigue_load_limit_kN": 0.98,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 11500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). the last two digits encode the bore: 13948 carries code 48 = 240 mm (code × 5). Envelope 240×320×60 mm (9.449×12.598×2.362 in) with a 40.0 mm radial section height, C 60.5 kN, C0 32 kN and Pu 0.98 kN. The open 13948 carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 240 mm shaft. Reference (thermal) speed 3800 r/min, limiting speed 2200 r/min, catalogue mass 11500 g.",
    "applications": [
      "crusher feeders",
      "large industrial gearboxes",
      "material-handling winches",
      "large conveyor drives"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for 13948 (C 60.5 kN, C0 32 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 13948 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The  suffix on 13948 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 2200 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 13948 chamfer so the 60 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 13948 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Assign interference to the rotating ring: on a 240 mm rotating shaft use a m6 seat with an H7 housing; reverse the logic if the outer ring rotates."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 13948?",
        "a": "SKF 13948 measures 240 mm bore × 320 mm OD × 60 mm width (9.449 × 12.598 × 2.362 in), mass about 11500 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 13948 work?",
        "a": "The final two digits of 13948 are bore code 48, multiplied by 5 to give 240 mm."
      },
      {
        "q": "Can 13948 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for 13948?",
        "a": "With a rotating inner ring use roughly m6 on the shaft and H7 in the 320 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "13948",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "13948",
      "13948"
    ],
    "locale_variants": {}
  },
  {
    "sku": "E-2RS1KTN9-H",
    "brand": "SKF",
    "manufacturer_designation": "E-2RS1KTN9 H",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 52,
    "D_mm": 18,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "weight_g": 2205000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The Exx series is a self-aligning ball bearing family. the final digit of E is the bore in millimetres: E-2RS1KTN9 H fits a 52 mm shaft (direct miniature spelling). Envelope 52×18×31 mm (2.047×0.709×1.22 in) with a -17.0 mm radial section height, C undefined kN, C0 undefined kN and Pu undefined kN. SKF spells the sealed execution E-2RS1KTN9 H (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore, here supplied with the 305 E adapter sleeve for mounting on a cylindrical 52 mm shaft. Limiting speed undefined r/min, catalogue mass 2205000 g.",
    "applications": [
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery",
      "pump shafts with mild misalignment"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "raceway smearing under marginal lubrication at start-up",
      "electrical pitting in VFD-driven motors without shaft grounding"
    ],
    "pitfalls": [
      "Catalogue ratings for E-2RS1KTN9-H (C undefined kN, C0 undefined kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The spherical outer raceway lets E-2RS1KTN9-H tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The 2RS1 contact seals on E-2RS1KTN9-H add drag and cap speed at undefined r/min; no thermal reference speed is published because seal and grease life govern, not the bearing steel.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The  suffix on E-2RS1KTN9-H denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the undefined r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount E-2RS1KTN9-H by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of E-2RS1KTN9-H?",
        "a": "SKF E-2RS1KTN9 H measures 52 mm bore × 18 mm OD × 31 mm width (2.047 × 0.709 × 1.22 in), mass about 2205000 g. It has two contact rubber seals (2RS1) and a lifetime grease fill."
      },
      {
        "q": "How do I read the E designation?",
        "a": "Miniature self-aligning bearings print the bore as the final digit, so E is a 52 mm bearing; the leading digits give the section family."
      },
      {
        "q": "Can E-2RS1KTN9-H take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      },
      {
        "q": "Which fits should I use for E-2RS1KTN9-H?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 18 mm housing; reverse the interference if the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "E",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "E-2RS1KTN9-H",
      "E-2RS1KTN9 H"
    ],
    "locale_variants": {}
  },
  {
    "sku": "EKTN9-H",
    "brand": "SKF",
    "manufacturer_designation": "EKTN9 H",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 52,
    "D_mm": 18,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "weight_g": 2205000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The EKxx series is a self-aligning ball bearing family. the last two digits encode the bore: EKTN9 carries code NaN = 52 mm (code × 5). Envelope 52×18×32 mm (2.047×0.709×1.26 in) with a -17.0 mm radial section height, C undefined kN, C0 undefined kN and Pu undefined kN. The open EKTN9 H carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore, here supplied with the 305 adapter sleeve for mounting on a cylindrical 52 mm shaft. Limiting speed undefined r/min, catalogue mass 2205000 g.",
    "applications": [
      "pump shafts with mild misalignment",
      "material-handling equipment",
      "industrial electric motors",
      "conveyor drum and pulley shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 52 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Assign interference to the rotating ring: on a 52 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "The K suffix means a 1:12 tapered bore: EKTN9-H is not a drop-in for the straight-bore version — it needs a tapered shaft or an 305 adapter sleeve.",
      "The  suffix on EKTN9-H denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the undefined r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 52 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets EKTN9-H tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of EKTN9-H?",
        "a": "SKF EKTN9 H measures 52 mm bore × 18 mm OD × 32 mm width (2.047 × 0.709 × 1.26 in), mass about 2205000 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in EKTN9 work?",
        "a": "The final two digits of EKTN9 are bore code NaN, multiplied by 5 to give 52 mm."
      },
      {
        "q": "How much misalignment can EKTN9-H tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like EKTN9-H allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can EKTN9-H take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "EKTN9",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "EKTN9-H",
      "EKTN9 H"
    ],
    "locale_variants": {}
  },
  {
    "sku": "K-H",
    "brand": "SKF",
    "manufacturer_designation": "K H",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 72,
    "D_mm": 27,
    "B_mm": 41,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "weight_g": 2306000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The Kxx series is a self-aligning ball bearing family. the final digit of K is the bore in millimetres: K H fits a 72 mm shaft (direct miniature spelling). Envelope 72×27×41 mm (2.835×1.063×1.614 in) with a -22.5 mm radial section height, C undefined kN, C0 undefined kN and Pu undefined kN. The open K H carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore, here supplied with the 2306 adapter sleeve for mounting on a cylindrical 72 mm shaft. Limiting speed undefined r/min, catalogue mass 2306000 g.",
    "applications": [
      "agricultural gearboxes",
      "textile machinery drives",
      "industrial fans and blowers",
      "woodworking machinery"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 72 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "At 72 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.",
      "The  suffix on K-H denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the undefined r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "At 72 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "The spherical outer raceway lets K-H tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of K-H?",
        "a": "SKF K H measures 72 mm bore × 27 mm OD × 41 mm width (2.835 × 1.063 × 1.614 in), mass about 2306000 g. It is open, with no shields or seals."
      },
      {
        "q": "How do I read the K designation?",
        "a": "Miniature self-aligning bearings print the bore as the final digit, so K is a 72 mm bearing; the leading digits give the section family."
      },
      {
        "q": "What load can K-H take?",
        "a": "Catalogue values for K H: dynamic C undefined kN, static C0 undefined kN, fatigue limit Pu undefined kN. Use C in life calculation and C0 for static checks at 72 mm bore."
      },
      {
        "q": "What is the speed rating of K-H?",
        "a": "SKF publishes only the undefined r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "K",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "K-H",
      "K H"
    ],
    "locale_variants": {}
  },
  {
    "sku": "KM-H",
    "brand": "SKF",
    "manufacturer_designation": "KM H",
    "series": "1200-series",
    "type": "self_aligning_ball",
    "d_mm": 240,
    "D_mm": 50,
    "B_mm": 154,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 1322000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The KMxx series is a self-aligning ball bearing family. the final digit of KM is the bore in millimetres: KM H fits a 240 mm shaft (direct miniature spelling). Envelope 240×50×154 mm (9.449×1.969×6.063 in) with a -95.0 mm radial section height, C undefined kN, C0 undefined kN and Pu undefined kN. The open KM H carries no shields or seals and relies on application lubrication and external sealing. The  suffix identifies the machined brass cage execution. The K suffix marks a 1:12 tapered bore, here supplied with the 322 adapter sleeve for mounting on a cylindrical 240 mm shaft. Limiting speed undefined r/min, catalogue mass 1322000 g.",
    "applications": [
      "paper-machine rolls",
      "marine deck machinery",
      "crusher feeders",
      "large industrial gearboxes"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder",
      "incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets KM-H tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The spherical outer raceway lets KM-H tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The K suffix means a 1:12 tapered bore: KM-H is not a drop-in for the straight-bore version — it needs a tapered shaft or an 322 adapter sleeve.",
      "The  suffix on KM-H denotes a machined brass cage: the choice for high speeds, marginal lubrication and shock/vibration duty, and temperature-tolerant where polymer cages are not.",
      "Catalogue ratings for KM-H (C undefined kN, C0 undefined kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount KM-H by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of KM-H?",
        "a": "SKF KM H measures 240 mm bore × 50 mm OD × 154 mm width (9.449 × 1.969 × 6.063 in), mass about 1322000 g. It is open, with no shields or seals."
      },
      {
        "q": "How do I read the KM designation?",
        "a": "Miniature self-aligning bearings print the bore as the final digit, so KM is a 240 mm bearing; the leading digits give the section family."
      },
      {
        "q": "How heavy is KM-H?",
        "a": "Catalogue mass is 1322000 g for KM H; seal and cage executions of the same envelope differ by a few grams."
      },
      {
        "q": "What load can KM-H take?",
        "a": "Catalogue values for KM H: dynamic C undefined kN, static C0 undefined kN, fatigue limit Pu undefined kN. Use C in life calculation and C0 for static checks at 240 mm bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "KM",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "KM-H",
      "KM H"
    ],
    "locale_variants": {}
  },
  {
    "sku": "11204-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "11204 ETN9",
    "series": "11200-series",
    "type": "self_aligning_ball",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 3.4,
    "fatigue_load_limit_kN": 0.18,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 112xx series is SKF's extended-inner-ring self-aligning ball bearing: the inner ring is wider than the outer, giving a longer shaft seat for locating-bearing duty. the last two digits encode the bore: 11204 carries code 04 = 20 mm (code × 5). Envelope 20×47×14 mm (0.787×1.85×0.551 in) with a 13.5 mm radial section height, C 12.7 kN, C0 3.4 kN and Pu 0.18 kN. The open 11204 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 20 mm shaft. Limiting speed 9000 r/min, catalogue mass 180 g.",
    "applications": [
      "woodworking machine cutter shafts",
      "locating-bearing positions on long shafts",
      "conveyor pulleys needing a wide inner-ring seat",
      "shafts with a single locating bearing against a shoulder"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "the extended inner ring acting as a thrust collar: never use it to carry axial load — locate with a shaft shoulder or locknut instead",
      "uneven loading of the two ball rows if the extended ring is not seated square on the shaft",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.18 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The fatigue load limit is 0.18 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The 112xx extended inner ring of 11204-ETN9 gives a wider shaft seat but the same 20×47×14 mm envelope as a 12xx of the same bore — the outer ring is interchangeable, the inner is not.",
      "The ETN9 suffix on 11204-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 9000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.18 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 20 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 11204-ETN9?",
        "a": "SKF 11204 ETN9 measures 20 mm bore × 47 mm OD × 14 mm width (0.787 × 1.85 × 0.551 in), mass about 180 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 11204 work?",
        "a": "The final two digits of 11204 are bore code 04, multiplied by 5 to give 20 mm."
      },
      {
        "q": "What is the speed rating of 11204-ETN9?",
        "a": "SKF publishes only the 9000 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      },
      {
        "q": "How much misalignment can 11204-ETN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 11204-ETN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1204-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 1204 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "1204-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 1204 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "11204-ETN9",
      "11204 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "11205-ETN9",
    "brand": "SKF",
    "manufacturer_designation": "11205 ETN9",
    "series": "11200-series",
    "type": "self_aligning_ball",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 4,
    "fatigue_load_limit_kN": 0.21,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 112xx series is SKF's extended-inner-ring self-aligning ball bearing: the inner ring is wider than the outer, giving a longer shaft seat for locating-bearing duty. the last two digits encode the bore: 11205 carries code 05 = 25 mm (code × 5). Envelope 25×52×15 mm (0.984×2.047×0.591 in) with a 13.5 mm radial section height, C 14.3 kN, C0 4 kN and Pu 0.21 kN. The open 11205 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 25 mm shaft. Limiting speed 8000 r/min, catalogue mass 220 g.",
    "applications": [
      "shafts with a single locating bearing against a shoulder",
      "agricultural machinery driven shafts",
      "fan shafts with thermal expansion take-up",
      "woodworking machine cutter shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "uneven loading of the two ball rows if the extended ring is not seated square on the shaft",
      "the extended inner ring acting as a thrust collar: never use it to carry axial load — locate with a shaft shoulder or locknut instead",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded",
      "brinelling from static overload or hammer blows during mounting"
    ],
    "pitfalls": [
      "At 25 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Mount 11205-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The extended inner ring is not a thrust collar — it cannot carry axial load; use a locknut or shaft shoulder for thrust location.",
      "The ETN9 suffix on 11205-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Mount 11205-ETN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "The fatigue load limit is 0.21 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 11205-ETN9?",
        "a": "SKF 11205 ETN9 measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 220 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 11205 work?",
        "a": "The final two digits of 11205 are bore code 05, multiplied by 5 to give 25 mm."
      },
      {
        "q": "What load can 11205-ETN9 take?",
        "a": "Catalogue values for 11205 ETN9: dynamic C 14.3 kN, static C0 4 kN, fatigue limit Pu 0.21 kN. Use C in life calculation and C0 for static checks at 25 mm bore."
      },
      {
        "q": "What is the speed rating of 11205-ETN9?",
        "a": "SKF publishes only the 8000 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1205-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 1205 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "1205-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 1205 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "11205-ETN9",
      "11205 ETN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "11206-TN9",
    "brand": "SKF",
    "manufacturer_designation": "11206 TN9",
    "series": "11200-series",
    "type": "self_aligning_ball",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 15.6,
    "static_load_kN": 4.65,
    "fatigue_load_limit_kN": 0.24,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 112xx series is SKF's extended-inner-ring self-aligning ball bearing: the inner ring is wider than the outer, giving a longer shaft seat for locating-bearing duty. the last two digits encode the bore: 11206 carries code 06 = 30 mm (code × 5). Envelope 30×62×16 mm (1.181×2.441×0.63 in) with a 16.0 mm radial section height, C 15.6 kN, C0 4.65 kN and Pu 0.24 kN. The open 11206 TN9 carries no shields or seals and relies on application lubrication and external sealing. The TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 30 mm shaft. Limiting speed 6700 r/min, catalogue mass 350 g.",
    "applications": [
      "shafts with a single locating bearing against a shoulder",
      "agricultural machinery driven shafts",
      "fan shafts with thermal expansion take-up",
      "woodworking machine cutter shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "uneven loading of the two ball rows if the extended ring is not seated square on the shaft",
      "the extended inner ring acting as a thrust collar: never use it to carry axial load — locate with a shaft shoulder or locknut instead",
      "electrical pitting in VFD-driven motors without shaft grounding",
      "excessive misalignment loading one ball row heavily and spalling it early"
    ],
    "pitfalls": [
      "Mount 11206-TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways.",
      "Fillet radii must clear the 11206-TN9 chamfer so the 16 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The 112xx extended inner ring of 11206-TN9 gives a wider shaft seat but the same 30×62×16 mm envelope as a 12xx of the same bore — the outer ring is interchangeable, the inner is not.",
      "The TN9 suffix on 11206-TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 6700 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Fillet radii must clear the 11206-TN9 chamfer so the 16 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 11206-TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 11206-TN9?",
        "a": "SKF 11206 TN9 measures 30 mm bore × 62 mm OD × 16 mm width (1.181 × 2.441 × 0.63 in), mass about 350 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 11206 work?",
        "a": "The final two digits of 11206 are bore code 06, multiplied by 5 to give 30 mm."
      },
      {
        "q": "Which fits should I use for 11206-TN9?",
        "a": "With a rotating inner ring use roughly k5 on the shaft and H7 in the 62 mm housing; reverse the interference if the outer ring rotates."
      },
      {
        "q": "How heavy is 11206-TN9?",
        "a": "Catalogue mass is 350 g for 11206 TN9; seal and cage executions of the same envelope differ by a few grams."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1206-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 1206 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "1206-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 1206 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "11206-TN9",
      "11206 TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "11207-TN9",
    "brand": "SKF",
    "manufacturer_designation": "11207 TN9",
    "series": "11200-series",
    "type": "self_aligning_ball",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19,
    "static_load_kN": 6,
    "fatigue_load_limit_kN": 0.305,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 540,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 112xx series is SKF's extended-inner-ring self-aligning ball bearing: the inner ring is wider than the outer, giving a longer shaft seat for locating-bearing duty. the last two digits encode the bore: 11207 carries code 07 = 35 mm (code × 5). Envelope 35×72×17 mm (1.378×2.835×0.669 in) with a 18.5 mm radial section height, C 19 kN, C0 6 kN and Pu 0.305 kN. The open 11207 TN9 carries no shields or seals and relies on application lubrication and external sealing. The TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 35 mm shaft. Limiting speed 5600 r/min, catalogue mass 540 g.",
    "applications": [
      "woodworking machine cutter shafts",
      "locating-bearing positions on long shafts",
      "conveyor pulleys needing a wide inner-ring seat",
      "shafts with a single locating bearing against a shoulder"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "the extended inner ring acting as a thrust collar: never use it to carry axial load — locate with a shaft shoulder or locknut instead",
      "uneven loading of the two ball rows if the extended ring is not seated square on the shaft",
      "fretting corrosion on a creeping shaft or housing seat",
      "cage damage from running beyond the limiting speed"
    ],
    "pitfalls": [
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 11207-TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "Catalogue ratings for 11207-TN9 (C 19 kN, C0 6 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The 112xx extended inner ring of 11207-TN9 gives a wider shaft seat but the same 35×72×17 mm envelope as a 12xx of the same bore — the outer ring is interchangeable, the inner is not.",
      "The TN9 suffix on 11207-TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5600 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Catalogue ratings for 11207-TN9 (C 19 kN, C0 6 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "Mount 11207-TN9 by heating the inner ring (max 120 °C) on a cylindrical bore — driving it home through the outer ring or balls brinells the raceways."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 11207-TN9?",
        "a": "SKF 11207 TN9 measures 35 mm bore × 72 mm OD × 17 mm width (1.378 × 2.835 × 0.669 in), mass about 540 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 11207 work?",
        "a": "The final two digits of 11207 are bore code 07, multiplied by 5 to give 35 mm."
      },
      {
        "q": "What is the speed rating of 11207-TN9?",
        "a": "SKF publishes only the 5600 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      },
      {
        "q": "How much misalignment can 11207-TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 11207-TN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1207-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 1207 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "1207-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 1207 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "11207-TN9",
      "11207 TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "11208-TN9",
    "brand": "SKF",
    "manufacturer_designation": "11208 TN9",
    "series": "11200-series",
    "type": "self_aligning_ball",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19,
    "static_load_kN": 6.55,
    "fatigue_load_limit_kN": 0.335,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 720,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 112xx series is SKF's extended-inner-ring self-aligning ball bearing: the inner ring is wider than the outer, giving a longer shaft seat for locating-bearing duty. the last two digits encode the bore: 11208 carries code 08 = 40 mm (code × 5). Envelope 40×80×18 mm (1.575×3.15×0.709 in) with a 20.0 mm radial section height, C 19 kN, C0 6.55 kN and Pu 0.335 kN. The open 11208 TN9 carries no shields or seals and relies on application lubrication and external sealing. The TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 40 mm shaft. Limiting speed 5000 r/min, catalogue mass 720 g.",
    "applications": [
      "locating-bearing positions on long shafts",
      "conveyor pulleys needing a wide inner-ring seat",
      "shafts with a single locating bearing against a shoulder",
      "agricultural machinery driven shafts"
    ],
    "failure_modes": [
      "lubricant starvation where no regreasing interval is maintained",
      "contamination wear when the open arrangement is used without adequate external sealing",
      "uneven loading of the two ball rows if the extended ring is not seated square on the shaft",
      "the extended inner ring acting as a thrust collar: never use it to carry axial load — locate with a shaft shoulder or locknut instead",
      "cage damage from running beyond the limiting speed",
      "raceway smearing under marginal lubrication at start-up"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring: on a 40 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "At 40 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.",
      "Use 11208-TN9 as a locating bearing: the extended inner ring sits against a shaft shoulder, while the non-locating bearing floats to take up thermal expansion.",
      "The TN9 suffix on 11208-TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 5000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "Assign interference to the rotating ring: on a 40 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.",
      "Catalogue ratings for 11208-TN9 (C 19 kN, C0 6.55 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 11208-TN9?",
        "a": "SKF 11208 TN9 measures 40 mm bore × 80 mm OD × 18 mm width (1.575 × 3.15 × 0.709 in), mass about 720 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 11208 work?",
        "a": "The final two digits of 11208 are bore code 08, multiplied by 5 to give 40 mm."
      },
      {
        "q": "How much misalignment can 11208-TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 11208-TN9 allow less (about 1°) because the seal lip binds first."
      },
      {
        "q": "Can 11208-TN9 take axial load?",
        "a": "A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1208-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 1208 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "1208-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 1208 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "11208-TN9",
      "11208 TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "11209-TN9",
    "brand": "SKF",
    "manufacturer_designation": "11209 TN9",
    "series": "11200-series",
    "type": "self_aligning_ball",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.9,
    "static_load_kN": 7.8,
    "fatigue_load_limit_kN": 0.4,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 770,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 112xx series is SKF's extended-inner-ring self-aligning ball bearing: the inner ring is wider than the outer, giving a longer shaft seat for locating-bearing duty. the last two digits encode the bore: 11209 carries code 09 = 45 mm (code × 5). Envelope 45×85×19 mm (1.772×3.346×0.748 in) with a 20.0 mm radial section height, C 22.9 kN, C0 7.8 kN and Pu 0.4 kN. The open 11209 TN9 carries no shields or seals and relies on application lubrication and external sealing. The TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 45 mm shaft. Limiting speed 4500 r/min, catalogue mass 770 g.",
    "applications": [
      "agricultural machinery driven shafts",
      "fan shafts with thermal expansion take-up",
      "woodworking machine cutter shafts",
      "locating-bearing positions on long shafts"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "the extended inner ring acting as a thrust collar: never use it to carry axial load — locate with a shaft shoulder or locknut instead",
      "uneven loading of the two ball rows if the extended ring is not seated square on the shaft",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 11209-TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 11209-TN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.",
      "The 112xx extended inner ring of 11209-TN9 gives a wider shaft seat but the same 45×85×19 mm envelope as a 12xx of the same bore — the outer ring is interchangeable, the inner is not.",
      "The TN9 suffix on 11209-TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.4 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 45 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 11209-TN9?",
        "a": "SKF 11209 TN9 measures 45 mm bore × 85 mm OD × 19 mm width (1.772 × 3.346 × 0.748 in), mass about 770 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 11209 work?",
        "a": "The final two digits of 11209 are bore code 09, multiplied by 5 to give 45 mm."
      },
      {
        "q": "What is the speed rating of 11209-TN9?",
        "a": "SKF publishes only the 4500 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      },
      {
        "q": "How much misalignment can 11209-TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 11209-TN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1209-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 1209 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "1209-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 1209 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "11209-TN9",
      "11209 TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "11210-TN9",
    "brand": "SKF",
    "manufacturer_designation": "11210 TN9",
    "series": "11200-series",
    "type": "self_aligning_ball",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 9.15,
    "fatigue_load_limit_kN": 0.475,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 112xx series is SKF's extended-inner-ring self-aligning ball bearing: the inner ring is wider than the outer, giving a longer shaft seat for locating-bearing duty. the last two digits encode the bore: 11210 carries code 10 = 50 mm (code × 5). Envelope 50×90×20 mm (1.969×3.543×0.787 in) with a 20.0 mm radial section height, C 26.5 kN, C0 9.15 kN and Pu 0.475 kN. The open 11210 TN9 carries no shields or seals and relies on application lubrication and external sealing. The TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 50 mm shaft. Limiting speed 4300 r/min, catalogue mass 850 g.",
    "applications": [
      "woodworking machine cutter shafts",
      "locating-bearing positions on long shafts",
      "conveyor pulleys needing a wide inner-ring seat",
      "shafts with a single locating bearing against a shoulder"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "the extended inner ring acting as a thrust collar: never use it to carry axial load — locate with a shaft shoulder or locknut instead",
      "uneven loading of the two ball rows if the extended ring is not seated square on the shaft",
      "excessive misalignment loading one ball row heavily and spalling it early",
      "rolling-contact fatigue spalling once the catalogue L10 life is exceeded"
    ],
    "pitfalls": [
      "The fatigue load limit is 0.475 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "Catalogue ratings for 11210-TN9 (C 26.5 kN, C0 9.15 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.",
      "The 112xx extended inner ring of 11210-TN9 gives a wider shaft seat but the same 50×90×20 mm envelope as a 12xx of the same bore — the outer ring is interchangeable, the inner is not.",
      "The TN9 suffix on 11210-TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4300 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The spherical outer raceway lets 11210-TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "Fillet radii must clear the 11210-TN9 chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 11210-TN9?",
        "a": "SKF 11210 TN9 measures 50 mm bore × 90 mm OD × 20 mm width (1.969 × 3.543 × 0.787 in), mass about 850 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 11210 work?",
        "a": "The final two digits of 11210 are bore code 10, multiplied by 5 to give 50 mm."
      },
      {
        "q": "What is the speed rating of 11210-TN9?",
        "a": "SKF publishes only the 4300 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      },
      {
        "q": "How much misalignment can 11210-TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 11210-TN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1210-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 1210 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "1210-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 1210 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "11210-TN9",
      "11210 TN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "11212-TN9",
    "brand": "SKF",
    "manufacturer_designation": "11212 TN9",
    "series": "11200-series",
    "type": "self_aligning_ball",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 31.2,
    "static_load_kN": 12.2,
    "fatigue_load_limit_kN": 0.62,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 1150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The 112xx series is SKF's extended-inner-ring self-aligning ball bearing: the inner ring is wider than the outer, giving a longer shaft seat for locating-bearing duty. the last two digits encode the bore: 11212 carries code 12 = 60 mm (code × 5). Envelope 60×110×22 mm (2.362×4.331×0.866 in) with a 25.0 mm radial section height, C 31.2 kN, C0 12.2 kN and Pu 0.62 kN. The open 11212 TN9 carries no shields or seals and relies on application lubrication and external sealing. The TN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 60 mm shaft. Limiting speed 3400 r/min, catalogue mass 1150 g.",
    "applications": [
      "woodworking machine cutter shafts",
      "locating-bearing positions on long shafts",
      "conveyor pulleys needing a wide inner-ring seat",
      "shafts with a single locating bearing against a shoulder"
    ],
    "failure_modes": [
      "contamination wear when the open arrangement is used without adequate external sealing",
      "lubricant starvation where no regreasing interval is maintained",
      "the extended inner ring acting as a thrust collar: never use it to carry axial load — locate with a shaft shoulder or locknut instead",
      "uneven loading of the two ball rows if the extended ring is not seated square on the shaft",
      "brinelling from static overload or hammer blows during mounting",
      "false brinelling from vibration while the shaft stands idle"
    ],
    "pitfalls": [
      "The spherical outer raceway lets 11212-TN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.",
      "The fatigue load limit is 0.62 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "The 112xx extended inner ring of 11212-TN9 gives a wider shaft seat but the same 60×110×22 mm envelope as a 12xx of the same bore — the outer ring is interchangeable, the inner is not.",
      "The TN9 suffix on 11212-TN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 3400 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.",
      "The fatigue load limit is 0.62 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.",
      "At 60 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast."
    ],
    "faq": [
      {
        "q": "What are the dimensions of 11212-TN9?",
        "a": "SKF 11212 TN9 measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 1150 g. It is open, with no shields or seals."
      },
      {
        "q": "How does the bore code in 11212 work?",
        "a": "The final two digits of 11212 are bore code 12, multiplied by 5 to give 60 mm."
      },
      {
        "q": "What is the speed rating of 11212-TN9?",
        "a": "SKF publishes only the 3400 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern."
      },
      {
        "q": "How much misalignment can 11212-TN9 tolerate?",
        "a": "Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 11212-TN9 allow less (about 1°) because the seal lip binds first."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "1212-ETN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 1212 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      },
      {
        "equiv_sku": "1212-EKTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 1212 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "11212-TN9",
      "11212 TN9"
    ],
    "locale_variants": {}
  }
]
